Thank you for your purchase of Ikelite equipment. Please read thisinstruction manual completely before attempting to operate or divewith this product. Please refer to the back page of this manual toregister your Ikelite product.

Port Lock

IKELITE

SLR-DC Housingi n s t r u c t i o n m a n u a l6871.07 Canon EOS 7D

2

Table of ContentsSpecifications ..............................................................P. 3Package Contents ........................................................P. 4Preparation ..................................................................P. 4Attach External “Tray with Handles” to Housing ............P. 4Parts of the Housing - Front/Side View ..........................P. 5Parts of the Housing - Back View ..................................P. 6Initial Camera Setup........................................................P. 7Opening the Housing ......................................................P. 7Housing Conversion Circuitry..........................................P. 8Setting the Conversion Circuitry Strobe ID Switch..........P. 8Using the Conversion Circuitry........................................P. 9Using Non-Ikelite or Ikelite Non-DS Strobes ..................P. 9DS50 and DS125 Strobe Compatibility ..........................P. 10Attaching the Flash Connection for External Strobes ....P. 10Attach Camera to Housing Tray ......................................P. 11Installing Camera in Housing ..........................................P. 11Closing the Housing ........................................................P. 12Final Check ....................................................................P. 12Attaching a Cync Cord to the Housing............................P. 13Turn Camera On..............................................................P. 13Zoom Clamp & Gear Sleeve Installation ........................P. 14Manual Focusing ............................................................P. 18Installing the Port ............................................................P. 19

Lens Ports ......................................................................P. 20Attaching an Ikelite Strobe Arm to the Housing Handle..P. 21

Table of Contents - continuedUsage ............................................................................P. 22Pre-Dive Your System ....................................................P. 22Lubricants ........................................................................P. 22Troubleshooting ........................................................P. 23Recommended Accessories ....................................P. 25Accessory Mounting Points ............................................P. 25EV-Controller Use............................................................P. 25Maintenance..................................................................P. 26Storing the Housing ........................................................P. 29Spare Parts ..................................................................P. 29Photo Tips ....................................................................P. 29Technical Support ........................................................P. 30Limited Warranty ........................................................P. 31Returning Products for Service ................................P. 31Product Registration ..................................................Back Cover

3

SpecificationsControls ..................All important camera functions are accessible. Controls not provided for Diopter Adjustment and Flash Button.Width ......................9.5in (240mm) including controlsHeight ....................6.7in (170mm) including controlsDepth ......................6.5in (165mm) including controlsWeight ....................5.5lb (2.5kg) without tray & handlesBuoyancy ................Neutral in freshwater; Dependant on lens & portBuilt-in Flash ..........NoStrobe Connection ..Ikelite digital TTL electrical bulkheadTray Mounting ........12-24 thread with 3in spacing (76mm)

- SLR-DC Housing- Envelope containing tray installation hardware, maintenance kit, and extra control end tips.

Package Contents- Aluminum Tray & Dual Handles - Silicone Lubricant- Standard Zoom Clamp & Sleeve Set- #5509.28 Large Diameter Zoom Clamp & Sleeve Set

This product has been water pressure tested at the factory and is depthrated to 200 ft. (60m). Thoroughly inspect and immerse the emptyhousing completely in water before installing a camera. If any foggingoccurs or droplets of water enter the housing, do not install a camera.Clean the housing main o-ring and retest to make sure that it iswatertight. Refer to the Troubleshooting section, page 23.We suggest that you read this instruction booklet thoroughly before useto have a full understanding of where each camera control is located,and what function each control provides. Please read your cameramanual thoroughly to have a full understanding of each camera function.If you are new to underwater photography, be sure to read the PhotoTips section. Due to the power required to operate the camera and LCD screen starteach dive with a fully charged camera battery.

Preparation

4

Attach External “Tray with Handles” to HousingUse hardware and instructionslocated in the clear Ikelite pouchto attach the “Tray with Handles”to your Ikelite housing.

Port Lock

IKELITE

5

Port Lock

IKELITE

Parts of the Housing - Front ViewQuick ReleaseStrobe Arm Mount

Handle

PortOpening

Gear SleeveDrive Gear

ShutterRelease

Multi-function Button

Main Dial

LidSnap

Side View

GearSleeve

OptionalPort

Port O-ring

Main HousingO-ring

Camera Tray

Camera MountingBolt

AF-ON

Shutter Release

Port Lock

Lid Snap

6

5

67

10

8

11

12

17

14

18

1

2

4

3

9

1315

16

Back View

Zoom

LensRelease/DOF

AF-ON

Aluminum Tray

QuickReleaseButton

Viewfinder Port

10. AE Lock11. AF Point12. Start/Stop13. External Strobe Connecter & Cap14. Set Button15. Quick Control Dial16. Quick Control Switch17. Flash Mode “-” Compensation18. Flash Mode “+” Compensation

Mode DialMeter Mode/WBAF Drive ModeISO

LCD Light Button

Shutter Release

1. Power Switch2. Quick Control Button3. RAW + Jpeg4. Menu5. Picture Style6. Info7. Playback8. Erase 9. Live View

- Housing controls are NOT provided for the Multi-Controller and Flash “pop-up” Button.

7

Initial Camera Setup- Insert a fully charged battery.- Insert a SD or SDHC memory card.- Set the mode dial to “M” manual.- Set shutter speed to 1/60th second or 1/125th second for fast

moving subjects.- Set aperture to F8 for general photography or F22 for macro

photography (close-ups).- Set Quality to highest jpeg setting “L” or RAW.- Set ISO to 100.- Set White balance to “Auto AWB.”- Set Metering Mode to “Center-weighted average.”- If using auto-focus in “Live-View”, use “Quick-Mode. Auto-focus will not

be as good in “Live-View” mode. - Disable “Auto Lighting Optimizer.”- Set AF mode to “One-Shot AF.”- Disable “Red-eye reduction.” - Set “Auto power off” to 8 minutes.- Set Image review to 4 seconds.

Opening the HousingLid Snaps have a Lock. To open,push Lid Snap Lock forward and lift asshown. Keep pressure on the LidSnap so it does not fly open quickly.

Lid Snaps have a lot of spring tensiononce they go over center, so have afirm grip on the Lid Snap. Lid Snapsmay be opened one at a time.

Lift

Push Forward

Lid Snap Lock

8

Setting the Conversion Circuitry Strobe ID Switch

Housing Conversion CircuitryThis housing contains Ikelite designed Conversion Circuitry. Onceattached, turn the strobe on first before turning on the camera.When used with Ikelite DS Strobes the Conversion Circuitry providesreal Nikon iTTL flash exposure with over and underexposurecompensation from +1 1/3 to - 1 1/3 f-stops in 1/3 stop increments.The Conversion Circuitry also offers Manual exposure control with 3 1/2f-stops of underexposure control in 1/2 stop increments.The Conversion Circuitry is powered by the Ikelite DS Strobe whenconnected to the housing with the 4103.51 single or 4103.52 dual synccord. When using two strobes with the dual sync cord, the primarystrobe connected to the cord without the red band, must be turned on topower the Conversion Circuitry. Always keep both strobes connected toyour dual sync cord underwater. Do not exchange your secondarystrobe for a dust cap which may not be waterproof.

On the housing back is a switch for setting the DS Strobe ID. Set theswitch to the Model of DS Strobe being used.

When using dual strobes of different models such as a DS51 and aDS161, set the ID switch to DS51 or the smaller strobe.

DS

DS

Set DS Substrobe to TTL Mode

50-51

TIGHTEN HOLDOWN BOLTWITH COIN

OR SCREWDRIVER

160-161125-200

Strobe ID Switch

9

Using Non-Ikelite or Ikelite Non-DS Strobes (Strobe50, 100A, 200, 400) with this Housing

The Conversion Circuitry is automatically disabled when used with aNon-Ikelite or Non-DS Strobe. These Strobes can be used in their manualmode utilizing any power settings provided on the Strobe.

Using the Conversion Circuitry (Set DS Strobe to TTL mode)- Mode and Compensation Buttons

The Conversion Circuitry default is set to TTL. To switch between TTL andManual Modes, depress both Mode Buttons at the same time and keepthem depressed until you see the desired Yellow LED Mode illuminate.

- TTL Mode (indicated when the yellow LED directly below TTL isilluminated). TTL Mode is the default setting. When the DS Strobe ispowered ON, the yellow TTL LED will illuminate. None of the Red LEDswill illuminate. This indicates that no (+) plus or (-) minus compensation isselected. Depress the Mode buttons to select +/- compensation. Note thatthe TTL +/- compensation values are in the yellow bar with the headingTTL.

- Manual Mode (indicated when the yellow LED directly below the M isilluminated). When the Manual Mode is selected, the Red LED directlybelow the F (full power) will illuminate. Note that the Manual minus (-)compensation values are in the black bar with the heading M. Set DSStrobe to TTL mode. This will allow the strobe power to be varied inmanual mode.

Red LEDs (Compensation)

Manual Mode - Yellow LED

TTL Mode - Yellow LED

Mode &Compensation

Buttons

When using an externalstrobe, connect the housinghotshoe connector. Slidethe connector into thehotshoe mount on thecamera from the back ofthe camera as shown. Slidethe connector forward untilit stops. Due to limitedclearance between thecamera hotshoe mount andthe housing back, thehotshoe connector shouldbe attached before thecamera is secured with themounting bolt.

10

DS50 and DS125 Strobe Compatibility- Older DS50 Strobes with Serial Number below 63,850 can NOT be

updated to operate correctly with the latest TTL conversion circuitry.Older DS50 Strobes with Serial Number between 63,850 and 69,999require upgrade of electronics to operate. Cost of update depends onstrobe circuitry. Strobe must be returned to Ikelite for evaluation toprovide an estimate of upgrade cost.

- Older DS125 Strobes with Serial Number below 2,500 can NOT beupdated to operate correctly with the latest TTL conversion circuitry.Older DS125 Strobes with Serial Number between 2,500 and 4,999require upgrade of electronics to operate. Cost of update depends onstrobe circuitry. Strobe must be returned to Ikelite for evaluation toprovide an estimate of upgrade cost.

Attaching the Flash Connection for External Strobes

External Strobe Connector and Waterproof Cap

Housing Back

HotshoeConnector

CANON

7DEOS

Installing Camera in HousingBefore installing the camera, pull out on the controls in the front section ofthe housing. This will allow the camera to slide in easier. Once the camerais installed and the lid snaps have been closed, return the controls to theiroperating position.

Attaching Camera to Housing TrayRemove the back from the housing. The mounting tray for the camera issecured to the housing back. Position the camera and lens on thecamera tray, and then secure it with the mounting bolt which threads intothe camera’s tripod socket.Use a flathead screwdriver (recommended) or coin to tighten theMounting Bolt so the camera bottom is flush against the tray.

Mounting BoltCamera Tray

11

o-ring

housing back

housing back

housing

housing

o-ring

12

Final CheckOnce the housing is closed, check the o-ring seal. Check the gapbetween the housing back and the housing. It should be even all theway around the housing.Look through the clear plastic back at the o-ring. You should see adarkened area where the o-ring is compressed against the housingback. If you do not see an even black compression seal all the wayaround the back, open the lid snaps, reseat the housing back and closethe lid snaps. Visually check the seal again.

Closing the Housing1. Place housing face down in your lap.2. Check to see that there is an o-ring on

the housing back that is clean and in itsproper location.

3. Guide the back onto the housing. Theo-ring should touch the housing all theway around. There shouldbe an even gap all the way aroundbetween the housing and the housingback.

4. Lift the lid snaps so they are extendedand place the lid snap into thecorresponding hook on the housingback.

5. To close the housing, push down on thelid snaps until they snap into place. Lidsnaps on opposite sides ofthe housing should be closedat the same time. Be sure theyare down far enough to engagethe lid snap lock.

even gapall 4 sides

The Housing Bulkhead is designed to accept only an Ikelite 5-pin TTLSync Cord.

1. Lightly lubricate the Sync Cord O-ring. Use ONLY Ikelite lubricant(supplied with housing).

2. Remove Bulkhead Cap from Housing Bulkhead.3. Line up the Sync Cord Pins with the corresponding Bulkhead

receptacles. Gently insert Sync Cord into Bulkhead. DO NOT force thisinstallation. If the Sync Cord does not seat properly inside the Bulkhead,the pins and receptacles are improperly aligned (repeat Step 3).

4. Tighten the Knurled Nut snugly using your Index finer and thumb. DONOT use pliers or other tools to tighten the Knurled Nut.

Always remove theSync Cord from yourHousing when not inuse, and replace theBulkhead Cap.

13

Turn Camera OnTurn the camera on and operate each of the housing controls to get afeel for using the camera in the housing. Take a few test shots on land.You are now ready to shoot underwater photos and video!

Attaching a Sync Cord to the Housing

Caution:Do not remove thewaterproof BulkheadCap unless anexternal sync cord isgoing to be pluggedin. Do not removeBulkhead Cap or SyncCord underwater.

Bulkhead Cap

Sync Cord O-ring

HousingBulkhead

Ikelite TTLSync Cord

Knurled Nut

Preparing to Install Zoom Clamp & Gear Sleeve

Determine the typeof lens being usedon the camera.Type 1 Lenses havea lens opening thatis NOT larger indiameter than thezoom ring. (Fig. 1).

Type 2 Lenses have a lensopening that IS larger in diameter than the zoom ring. (Fig. 2).

Zoom Clamps & Gear Sleeves Included with HousingThere are 2 differentZoom Clamps andGear Sleevesprovided with thehousing. Start withthe suggested ZoomClamp and GearSleeve dependingon the Type oflens being used.See (Fig. A or B)

lensopening

zoomring

bayonetmount

Type 1 lens Type 2 lens(Figure 1) (Figure 2)

Normally used withType 1 lens (Fig.1)

#9059.8 small diameter clamp:For use with #0073 sleeve

+

#0073 sleeve: Use withsmall diameter zoom clamp

#9059.8Figure A

Normally used withType 2 lens (Fig.2)#5509.28 Package

#9059.9 large diameter clamp:For use with #0073.1 sleeve

+

#0073.1 sleeve: Use withlarge diameter zoom clamp

#9059.9Figure B

thick ribs thin ribs

widegroovedextensiontabs

narrowgroovedextensiontabs

14

Installing the Zoom Clamp & Gear Sleeve On the Type 1 Lenses

The Zoom Clamp has springs so it can be expanded to fit over theZoom Ring of the lens - figure C, page 15. Install the Zoom Clamp with the extension tabs toward the rear elementof the lens. After installing the Zoom Clamp and Gear Sleeve - figures D& E, page 16, install the Lens Port and rotate the Zoom Ring on thelens. If the Zoom Ring and Gear Sleeve do not mesh properly, install therubber strips (supplied) to the inside diameter of the Zoom Clamp asshown in figure F, page 16. Two thicknesses of rubber strips are provided. Start by installing thethinnest rubber strips. If the Zoom Clamp still is not tight enough andmeshes improperly with the Gear Sleeve, use the thicker rubber strips.Reinstall the Zoom Clamp, Sleeve. Mesh Gear Sleeve teeth with BlackHousing Drive Gear, figure G, page 18, and then install the Lens Port.After installing the port, pages 19 & 20, rotate the housing Zoom ControlKnob to see that the Gear Sleeve is properly rotating the lens Zoom ring.

15

Figure C

Type 1 lensmountedto camera

zoomring

16

Figure D

Figure E

Align Ribs withZoom Clampgrooved tabs

applyrubber stripsto inside ofclamp

Figure F

Type 1 Lenses - continued

Gear Sleeve Ribs

TOP OF HOUSING

Installing the Zoom Clamp & Gear Sleeve On Type 2 LensesDue to the larger diameter lens opening on Type 2 lenses, the ZoomClamp and Gear Sleeve need to be installed from the rear (bayonet end)of the lens. Use the housing Lens Release Control and remove thecamera lens from the camera body, after the camera and lens havebeen installed in the housing.Place the Gear Sleeve in the housing opening as shown.Install the black Zoom Clamp on the Lens Zoom Ring and lower the lensinto the housing opening. Make sure the Zoom Clamp grooved tabsalign with the Gear Sleeve ribs. If necessary, install rubber strips toexpand the Zoom Clamp so it meshes properly with the Gear Sleeve.Bayonet lens into camera body and align Gear Sleeve teeth with BlackHousing Gear Teeth.

Zoom Clamp

Type 2 lens

Lens Zoom Ring

AlignZoom Clampgroovedtabs withGear SleeveRibs

17

Gear Sleeve

Lens ManualFocus Ring

Manual FocusingIkelite DSLR housings are designed for auto-focus DSLR cameras andlenses. Manual focusing is not recommended. In some cases, if youdesire to manually focus a lens, the zoom clamp must be moved ontothe lens Manual Focus Ring and you must use the housing zoom controlknob to manually focus. This will result in loss of zoom capability.

18

Installing Zoom Clamp/Sleeve on Type 2 Lenses - continuedBefore installing the lens port and checking operation, make sure theteeth on the Gear Sleeve mesh with the teeth on the housing Drive Gear,shown below. When the port is installed, pages 19 & 20, it will lock theGear Sleeve in place. After installing the port, rotate the housing ZoomControl Knob to see that the Gear Sleeve is properly rotating the LensZoom ring.

IKELITE

MeshGear Sleeveteeth withBlackHousingDrive Gear

Figure G

Port LockReleaseButton

Port Lock

Installing the PortThere are four port locks on thefront of the housing, see figureG, page 18. Each port lock hasa Release Button. Lift therelease button and slide eachPort Lock away from the portopening. In the unlockedposition, the Release Button willremain in the up position asshown.

To prepare the port forinstallation, remove the port o-ring and lightly lubricate it. The port sealis a side-to-side seal and requires the o-ring to be lightly lubricated foreasy installation. Put a small amount of lubricant on your fingers and pullthe o-ring through your fingers to lightly lubricate it. Do not stretch theo-ring. Check that the lip of the port where the o-ring fits and the sealingsurface on the housing are clean. Place the port, with o-ring, into thehousing port opening. Press down on the port firmly and evenly until youfeel the port slide into place. Continue to push down on the port andpush each port lock forward until the lock fully engages. It may help toslightly rotate the port as you push in on the port lock. Visually inspecteach port lock and confirm that the Port Lock Release Button is seatedflush against the Port Lock Body. Do not rely on an audible "click" toindicate that the lock is engaged. Check around the perimeter of the port seal to see that the o-ring isproperly sealed and not extruded, figure 2, page 20.It is NOT necessary to tighten housing port locks after installing a port.Port locks are factory adjusted. Slight port movement is normal after portlocks have been closed and port has been secured to the housing.

Port LockReleaseButton

Lift ReleaseButton toUnlock

Pull Back to DisengagePort

Locked Position

19

Installing the Port - continued

To Remove PortTo remove the port, lift up on each Release Button and slide the portlock away from the port.

Port Seal Inside ViewIf the port is installed before the camera isinserted into the housing, look from theinside of the housing at the port seal.Check to see that the o-ring is properlyseated as shown in figure 1 and notextruded as shown in figure 2.

Fig. 1

Fig. 2

Caution:After installing the port, turn the Zoom Control knob on the housing. If theZoom Control is difficult to turn, the gear sleeve may be warped. Ifnecessary, reduce or omit any rubber installed on the Zoom Clamp, figureF, page 16. If the Zoom Clamp is still warped, use of the 5509.28 packagemay be required, see page 14.

Lens PortsA lens port must be secured to the housing before entering the water.Ikelite DSLR housings DO NOT come with a lens port. You must selectthe correct port for each lens you will be using underwater. For completelens port information and compatibility with your Ikelite system, go toikelite.com.

20

21

Attaching an Ikelite Strobe Arm to the Housing HandleTo attach an Ikelite Arm to your Housing Handle, depress thespring-loaded Handle Push Button until it stops. Gently slide thepronged end of the Ikelite Arm into the hole in the top of the Handle asshown.

When the Ikelite Arm is properly seated, the Handle Push Button willreturn to its starting position.

Ikelite Arm

Handle Push Button

Housing Handle

22

Pre-Dive Your SystemIt is recommended that you take the complete system into a swimmingpool before use in open water. This will give you a chance to becomefamiliar with the handling and operation of your housing and strobe(s).

As soon as you enter the water, take a moment and check the housingto see that it is properly sealed. Next, check to see if there are anybubbles on the face of the port. If there are, take your fingers andremove them. If there are bubbles on the lens port they can produce softfocus spots in your photographs.

LubricantsIkelite provides silicone lubricant with the housing. We recommend thatyou use only Ikelite lubricant. Other brands may cause the o-ring toswell and not seal properly.Use only enough Ikelite lubricant to lightly cover control shafts ando-rings. Wipe off any excess lubricant with a clean cloth. Lubricant is nota sealant and is used to reduce friction. Excessive lubricant can collectsand and dirt which may interfere with proper sealing.

Note: Lubricant is not needed on the main housing o-ring to maintain ahousing seal, however, lightly lubricating this o-ring can extend it’s lifeand aid in seeing a good housing seal. Too much lube can attract debrisincreasing the potential for a leak.

CAUTION: Never use spray lubricants as the propellant ingredientcan cause the plastic housing to crack. Use ONLY Ikelite lubricant.

Usage

23

Troubleshooting

Push buttons orcontrols are stickyand hard to operate

- Remove the camera and rinse the closed housing in fresh water. Vigorously press each push button in and out several times to release any trapped saltwater or debris.- Press a sticky push button all the way in and place a small amount of lube on the small end of the push button shaft at it’s base. Release and operate the push button several times to distribute the lube.- If a control is sticky, grab the control knob, pull it out, and then push back in. If still sticky, see the Control Maintenance section - pages 26 & 27.- Return housing to Ikelite for routine maintenance.

Problem Solution

Image is over- orunder-exposed

- Check that the strobe(s) are firing when taking a picture. - When using an external strobe, make sure it is turned on, set properly, and it’s battery is charged.- Check any corded connection points. - Adjust camera shutter speed, aperture, or exposure compensation.- Move closer to or further away from the subject.

Water enters thehousing

- Remove, clean and properly lubricate the main housing and port o-rings.- Look for hairs, dirt, or foreign debris crossing the o-ring seal.- Reassemble the housing without a camera installed and pressure test or take diving.- Return housing to Ikelite for routine maintenance.

24

Camera does nottake a picture

- Install a fully charged battery.- A housing control is engaging a camera function and will not allow the shutter to fire.- There is not enough available light for the camera to properly focus. Add a focusing light or strobe with a built-in focusing light to your system.- Select a center focus point in your camera menu.

Problem Solution

Fogging occurs onthe Lens Port

- Humid air is trapped inside the housing. The camera produces heat and may condense any trapped moisture forming fog on the lens port. Close the housing in an air-conditioned room or vehicle, or in front of an air-conditioner. - The housing should not be in direct sunlight for an extended period of time.- Purchase desiccant packs from a local camera store and place one or two packs in your housing before each day of diving.- If water droplets or moisture is present around the controls or sealing areas, return the housing to Ikelite for evaluation. - Clean the main housing o-ring, port o-ring, and sealing surfaces of the housing.

- Make sure the camera is mounted properly on the camera tray and housing controls are out of the way .

Housing is hard toclose

Pictures are too blueor too green

- Use custom (manual) white balance if available.- Add an external strobe.- Move in closer to your subject when taking a picture.

EV-Controller UseTTL flash control is not available when using an EV-Controller, andtherefore an EV-Controller is not recommended for use with thishousing.Note: The EV-Controller cannot be used as a slave. If hardwired to thehousing, set the EV-Controller to Non pre-flash. The EV-Controller used with Ikelite DS Strobes has two user settings.One setting is for strobe selection, the other is for pre-flash “P” or nonpre-flash “ P .” Most cameras use a pre-flash. This means theEV-Controller should be set to the pre-flash “P” position when used withthis camera as a slave. If a manual mode is used that does not emit apre-flash, set the EV-controller to the non pre-flash “ P ” position.

A full range of accessories are available to support your housing. Pleasevisit ikelite.com to see the most current information about recommendedaccessories for your housing.

25

Recommended Accessories

Accessory Mounting PointsThe top of the SLR-DC housing features a 1/4-20 threaded mountingpoint for the attachment of a focus light, video light or other lightweightaccessories. DO NOT attach heavy items to this mount and always usethe correct length screw to attach a component.

The bottom of the SLR-DC housing tray also features five 1/4-20 threaded mounting points for attachment of a tripod or otheraccessories.

26

Control Maintenance Ikelite controls are designed to provide years of reliable service withminimal maintenance.

- Push button controls require no maintenance other than rinsing in freshwater after saltwater use. If a push button control becomes difficult topush or if it sticks when depressed, soak the housing in luke warm freshwater. After a few minutes, operate the push button. If this does notcorrect the problem, return the housing to Ikelite for maintenance.

- Some of the controls have long shafts. These controls can be pulled out,exposing the shaft, diagram B, page 27. To lubricate the control, gently pull on the knob until the stainless steelshaft is exposed. Lightly lubricate the shaft, then move the shaft in andout several times. This will lubricate the x-ring in the Ikelite control gland.This should be done before using the housing after a prolonged storageperiod, or once a week when the housing is in constant use.

- Some of the controls have a short shaft and cannot be pulled outexposing the shaft for lubrication. In the unlikely event one of thesecontrols sticks or becomes difficult to operate you can remove thecontrol from the housing and lubricate it, or return the housing to Ikelitefor maintenance. To remove the control, diagram A, page 27, loosen theset screw in the knob (allen wrench required); remove the knob. If thereis salt or dirt build-up on the exposed control shaft, clean the shaft.Open the housing and gently slide the control shaft out of the controlgland. Clean and lightly lubricate the shaft, including the end of theshaft. Slide the shaft back into the control gland and gently slide it backand forth a few times without fully removing the shaft from the gland.Replace the knob noting the flat area on the shaft. The set screw in theknob should tighten down against the flat area on the control, so theknob does not turn on the shaft.

Maintenance

27

Housing

Lubricate Shaft

Pull out toexpose shaft

Diagram B

Loosen set screw(allen wrench required)

Tighten set screw downagainst this flat area

when replacing the knob.

HousingGland

Control Shaft

Lubricate end of shaftbefore reinserting intogland

Diagram A

28

Housing MaintenanceYour Ikelite Housing should be given the same care and attention asyour other photographic equipment. In addition to normal maintenance,we recommend your housing be returned to Ikelite (every 2-3 years or50 dives), to be checked and pressure tested.

- Do Not leave the camera and housing in direct sunlight for prolongedperiods. Heat may damage the camera.

- Do Not ship the camera in the housing.- Before using the housing, always check the tightness of the set screw

in each control knob. Check each control gland penetrating the housing to make sure theyare tight. There is a slight chance that either could vibrate loose duringtravel.

- Keep the back and port o-ring clean and lightly lubricated. To lubricate,remove the o-ring from the back. Put a small amount of lkelite lubricanton your fingers. Pull the o-ring through your fingers to apply a lightcoating of lubricant. Only apply enough lubricant to make the o-ring feelslick. Do Not stretch the o-ring. This light coating of lubricant will helpto keep the o-ring from drying out and will help to show a dark sealingline when the housing back is properly sealed.

- Keep the area where the o-ring fits and the sealing surface clean.- Rinse the housing exterior thoroughly in freshwater after each saltwater

use. Depress push buttons several times during rinse. Dry with a softcloth. Dry port to eliminate water spotting.After several uses in saltwater, soak the housing in a mild soap solution,rinse, and dry.

- Although not recommended, if it is necessary to remove a housing pushbutton, Do Not re-use the E-clip. Contact Ikelite for replacement E-clips(part #0319.12).

CAUTION: Never use spray lubricants as the propellant ingredient cancause the plastic housing to crack. Use only Ikelite lubricant.

29

Storing the HousingWhen the housing is going to be stored for a prolonged period it shouldbe soaked in a mild soap solution, rinsed, and dried thoroughly. Removethe back and port from the housing. Remove the back and port o-rings,lightly lubricate them and place them in a plastic ziploc bag. Place theplastic bag inside the housing for storage. Operate the push buttonsperiodically.

t0132.61 ..........Spare Main Housing O-ring

0105 ................Spare Port-to-Housing O-ring

5020 ................Silicone Lubricant in 4 1cc Tubes

5512.69 ............O-ring Kit with Main O-ring, Port O-ring, & 1cc Lubricant

0333.6 ..............Tray Mounting Screw 12-24 x 1/2 in. Stainless

0212.12 ............1/4 in. Shoulder Washer for 12-24 Screw

9104.5 ..............Waterproof Bulkhead Cap

0200.91 ............Body Cap

Photo Tips- The number one rule in underwater photography is to eliminate as much

water between the camera and subject as possible. Get as close as youcan to the subject, then use the zoom. If you are using flash for stillphotos, subjects beyond 6 feet (1.8m) will not have much colorregardless of strobe power.

- Photograph in clear water; do not stir up the sand or silty bottom. Ifbackscatter becomes a problem in the environment you arephotographing, an external flash will help eliminate much of thebackscatter.

Spare Parts

- Many digital cameras have a slight lag time between when you pressthe shutter release button and the camera actually takes the picture.Hold the housing steady a second or two after pressing the shutterrelease button.

- Do not shoot down on subjects as they will quite often blend into thebackground and be difficult to see in the photograph. Shoot subjectsstraight on or shoot up at a slight angle using the blue water as acontrasting background.

- When using daylight or flash, if your camera consistently over orunderexposes the image, you may want to adjust your camera’sexposure compensation settings.

- If you error in exposure, it is better to have the image slightlyunderexposed rather than overexposed. An overexposed image ismissing color information which cannot be adjusted in a photoprocessing program. A slightly underexposed image has colorinformation that can be adjusted.

- It is important to respect all living creatures underwater, includingpeople, marine life, and coral. While we encourage people to get closeto their subjects when taking a photograph, they should not touch, lie on,or in any way disturb the things they find underwater.

30

Ikelite Technical SupportEmail: ikelite@ikelite.comPhone 317.923.4523Fax 317.924.7988

Technical SupportPlease read the troubleshooting section of this instruction manual beforecontacting Ikelite Technical Support.

Photo Tips - continued

Returning Products for Service (outside the United States)For the separate international customs documentation form that youcomplete to accompany the shipment, please state or designate that theenclosed products were originally manufactured in the USA and arebeing returned to the manufacturer for repair service. Value of theequipment listed for customs purposes should be zero.

Ikelite is most interested in performing any service to ensure that allproducts perform as intended. Evidence of purchase date must beprovided to obtain warranty service.No prior authorization is required. You may return directly to us orthrough your dealer. Please include a brief description of the problem,any relevant email correspondence, and/or instructions on what youwant us to do. Always include name, shipping address, email address,and phone number inside of the package. Send postage paid to:

Ikelite Underwater SystemsAttention: Service Department50 West 33 StreetIndianapolis, IN 46208 USA

No reimbursements for postage paid will be issued.You may also want to insure the package.

Returning Products For Service

31

This Ikelite product is warranted against any manufacturing defects for aperiod of one (1) year from the original date of purchase. Defectiveproducts should be returned to Ikelite postage paid. Ikelite will, at its solediscretion, repair or replace such products, and will return to customerpostage paid. All other claims of any nature are not covered. Except asmentioned above, no other warranty expressed or implied applies to thisIkelite product.

Limited Warranty

Ikelite Underwater Systems50 West 33rd Street

Indianapolis, IN 46208 USA

ikelite.com

Product RegistrationPlease go to ikelite.com to register your Ikelite housing within 15 daysof purchase.

6871.07_Canon_7D_06 -0718