Mounting on 35 mm DIN rail, 4 spacing units wide

Standard input voltage 12V / 24Vpermissible range, lower limit (DC) 8 Vpermissible range, upper limit (DC) 28 VTime of day

Number of digital inputs 8 (shared with digital outputs)Type of digital input Galvanically isolated serializer with interruptInput voltage range 0-28VLogic HIGH voltage >11VLogic LOW voltage <3VMaximum trigger frequency 10 KHzProtection of digital outputs Short-circuit, over-current, over-temperature, ESD, transients.

Number of digital outputs 8 (shared with digital outputs)Type of digital output Galvanically isolated high-side driver (Charge pump NFET)Output voltage range Tied to supply voltage (6.5-32V)Maximum current per output 2.6 AMaximum total current 6.5 AMaximum switching frequency 400 HzProtection of digital outputs Short-circuit, over-current, over-temperature, ESD, transients.

Number of analog inputs 4Type of analog inputs Buffered ADCRange of voltage measurement 0-10VRange of current measurement 0-20mASwitching of voltage / current mode Automatic - in softwareResolution 18BitConversion rate 18bit: 3.75 Hz - 16bit: 15 Hz - 14bit: 60 Hz - 12bit: 240 HzProtection of analog inputs ESD, transients.

Number of analog outputs 2Type of analog outputs Buffered DACRange of output voltage 0-10VRange of output current 0-20mASwitching of voltage / current mode Automatic - in softwareResolution 12BitUpdate rate 20 KHzProtection of analog outputs Short-circuit, over-current, over-temperature, ESD, transients.

Isolation topology Isolated from MCU and analog field sectionDuplex type Half duplexNumber of receivers on bus 32Data rate 1 Mbps

Isolation topology Isolated from digital and analog field sectionNumber of pins 14Voltage level 5VProtocols supported SPI, I2C, UART, 9 GPIO'sProtection of expansion port ESD, transients.

LCD 128x64 pixel FSTN with dimmable backlightPush buttons 3 - push button membrane panel

Protection class IP20Ambient operating temperature 0 - 55 °C

Width 71.5 mmHeight 87 mmDepth 58 mmWeight 150 g

Document updated: 8.03.2015

Installation

Supply voltage

Digital inputs

Dimensions

Analog inputs

Analog Outputs

Digital outputs

Communication portsRS485

Expansion port (direct MCU control)

User Interface

Enviromental

Ind.I/O Datasheet

Industruino Ind.I/O is the Arduino-compatible equivalent of a PLC. The interface board offers 8 channels of 24V I/O, 4 channels of 0-10V/4-20mA 18bit ADC, 2 channels of 0-10V/4-20mA 12bit DAC, isolated RS485 transceiver, isolated power zones.

-dustruino and analog peripherals, the GND line of the analog section should be tied to the GND

*When operating in an electrically noisy environment it is possible to use a seperate power supply for your analog peripherals. This will improve the stability of your analog input/output

analog supply’s GND line.

*The majority of IND.I/O board functions are controlled via i2c, therefore it requires the “Indio” Arduino library which can be found on our website’s support page.

https://industruino.com/page/techcentre

2x CHOUTPUT

EXPANSION PORT14 pin IDC

6.5-32V 8x CHPOWER-IN Digital INPUT/OUTPUT

RS485

D0/R

XD2

/SDA

D7 D4/A

6D1

0/A1

0SC

LK/D

15M

ISO

/D14

D1/T

XD3

/SC

L

D6/A

7D5

/PW

M

ISO

2M

OSI

/D16

+5V

4-20 mA 0-10 V

Analog

4x CHINPUTAnalog

V+ CH1

CH1

CH1

CH2

ISO1

ISO1

CH2

CH3

CH4

CH2

CH3

CH4

CH5

CH6

CH7

CH8

40

1

6.5-32 V

Analogzone

MCUzone

Digitalzone

Ind.I/O Baseboard Pinout

Notes

Date: 02.06.2017

INDUSTRUINO IND.I/O - PRODUCT DATASHEET. JUNE 2017Industruino is an Arduino compatible industrial controller. www.industruino.com