instruction guide 6792 - tractorseats.com · instruction guide 6792 installation support phone...

INSTRUCTION GUIDE 6792

INSTALLATION SUPPORT

Phone 1-800-328-1752 / Web Site www.tractorseats.com

1. Remove old seat and suspension.

2. Cut out 4 1/2” of the cab metal from the left side of the existing seat well cavity. (Use of a Sawzall is recommended.)

3. Place the SWEK into the opening from the bottom side and fasten with sheet metal screws. Use a 5/32” drill bit for the holes.

4. Proceed with installation page 2.

John Deere 30 Series Seat Well Extension Kit for tractors with 7 1/2” wide seat well

page 1

SWEK PN : 6052

Installation Instructions to Replace a JD Deluxe Seat Suspension with a 402 Uni Pro Seat and Mechanical Suspension in an Early 30 Series Row CropTractor with Sound-Gard Cab




1. For models with the slanted front section on the seat well, bolt the PED JD W43A plate to the bottom of the PED JD W43 with two 5/16” x 3/4” carriage bolts and flange nuts. For models with the square front, use the W43B plate.

PED JD W43 PN:6051

W43A

5/16 - 18 X 3/4 CARRIGE BOLT

5/16 - 18 FLANGE NUT

W43B

page 2





1. Bolt the slide rails to the suspension with four 8mm x 12mm bolts. The slide rail lever must be assembled on the left side of the seat and suspension.

Note: Use Slide Rails PN:6048 that were shipped with. Remove and discard slide rails attached to seat bottom.

8mm x 12mm Bolts

page 3

Installation Instructions to Replace a JD Deluxe Seat Suspension with a 402 Uni Pro Seat and Mechanical Suspension in an Early 30 Series Row Crop Tractor with Sound-Gard Cab




1. Bolt the 6080 SAP to the slide rails with four 5/16” x 3/4” flat head socket cap screws, and 5/16” jam nuts. Place three washers in between the slide rails and SAP 6080, one on each bolt. Two on the right slide rail and one on the rear hole of the left slide rail to allow the SAP 6080 to sit level. Use the holes so the SAP 6080 is offset to the right.

5/16” X 3/4” FLAT HEAD SOCKET CAP SCREWS

5/16-18 JAM NUT 5/16 FLAT WASHERS

page 4

Installation Instructions to Replace a JD Deluxe Seat Suspen-sion with a 402 Uni Pro Seat and Mechanical Suspension in an Early 30 Series Row CropTractor with Sound-Gard Cab

SAP 6080





5/16-18 x 3/4 HEX HEAD BOLTS

5/16-18 LOCK NUTS

SPACERS

1. Bolt the suspension to the W43 pedestal with four 5/16” x 3/4” bolts, small spacer bushings and lock nuts. The small spacer bushings go in between the W43 pedestal and the suspension. You will have to unhook the rubber boot from the bottom of the suspension to get inside and fasten the nuts. It will help to raise the suspension up to create some space to get inside the suspension.

PED JD W43 PN:6051

page 5




1. Mount the PED W43 to the back of the cab with the original bolts.

2. Use the two holes on the W43A or W43B plate (which ever one is installed) as a guide and drill through the cab platform. Secure which ever plate is installed to the cab deck with two 5/16” x 3/4” bolts and flange nuts.

5/16x 18 x 3/4 Hex Bolt

5/16 x 18 Flange Nut

page 6


PED W43





5/16-18 x 5/8 Socket Head Cap Screw

5/16 Lock Washer

5/16-18 Jam Nut

1. Install the Grammer Swivel. This can be installed two different ways. The lock lever can be installed to the front or rear left of the seat. If you plan on locking the swivel to move freely it is recommended to install the lever to the rear left. When the lever is installed to the front left and locked out, it can hit the tractor seat platform when driving on rough terrain (depending on where the seat is located fore and aft).

2. Place the swivel onto the SAP 6080. If you are installing the swivel lock lever to the front left the square part of the swivel will go against the SAP 6080. For the lock lever to the rear left, place the rectangular side of the swivel against the SAP 6080. The swivel should be centered side to side and the front edge should be close to flush with the SAP 6080. Locate the four mounting holes and break the plastic knockouts from the swivel. Fasten the swivel down using four 5/16” x 5/8” socket head cap screws, lock washers, and jam nuts. The lock washer goes on the screw first, then through the swivel and SAP 6080 with the jam nut on the bottom.

page 7A

OPTIONAL SWIVEL INSTALLATION (If no swivel continue to page 8.)





5/16-18x5/8 Socket Head Cap Screws

5/16-18x1 Flat Head Socket Cap Screws

5/16-18 Flange Nuts

Flat Bar Spacer

page 7B

1. Install the seat. Remove the seat cushion by removing the two screws from the bottom front of the seat. Place the seat onto the swivel. NOTE: If the swivel was installed with the lock lever to the front left, you will have to place the 5/16” x 1 1/8” flat bar that came with the swivel onto the rear channel of the swivel plate. Center the seat so that two front holes and two rear holes line up. Remove the plastic knockouts from the swivel where the seat holes line up. NOTE: If the lock lever on the swivel is on the front left, the rear seat holes will line up with the holes on the flat bar. Fasten the seat down using two 5/16” x 5/8” socket head screws and flange nuts on the front. If the swivel lock lever was installed to the front left, use two 5/16” x 1” flat head socket cap screws and flange nuts on the rear two holes. If the swivel lock lever was installed to the rear left, use another two 5/16” x 5/8” socket head cap screwsand flange nuts. Tighten all hardware.

2. Reinstall the seat cushion.





5/16-18x5/8 Socket Head Cap Screws

5/16-18x1 Flat Head Socket Cap Screws

5/16-18 Flange Nuts

page 8

1. Remove the seat cushion by removing the two screws from the bottom front of the seat Remove the slide rails that are attached to the seatbottom.

2. Place the seat onto the SAP 6080. Use two 5/16-18x1 Flat Head Socket Cap Screws and Flange Nuts in the front and two 5/16-18x5/8 Socket Head Cap Screws and Flange Nuts in the rear

3. Reinstall the seat cushion.

SAP 6080

instruction guide 6792 - tractorseats.com · instruction guide 6792 installation support phone...

Documents