Getting StartedTelVue® ProVue™ SDI and Analog

2Press the Down arrow on the server’s LCD display to access the Menu. If there is more than one network cable attached to the system, then the first menu will ask which device you want to configure. See diagram for the port numbering.

The Up and Down arrows can be used to select which device to configure. Once the appropriate device has been found, press Enter to continue with the configuration process.

Select “yes” by using the Up and Down arrows at the DHCP menu to configure the selected ethernet device automatically.

To specifiy the IP address statically, select “no” at the DHCP menu and press Enter. Then use the Left and Right arrows to select the part of the IP address to modify. Use the Up and Down arrows to adjust its value. An underscore will appear below the part of the IP address that is being modified.

Once a valid IP address has been entered, press Enter to accept.

Configure the subnet mask and default gateway using the above instructions. Press Enter after each address has been configured. Generally, eth0 should be used for control, and eth1 for video. Note that out of the box, eth0 is set to DHCP, and eth1 is set to static IP 1.1.1.1.

Configure Networking

3Press the Down arrow to access the menu. Use the Right arrow button to navigate to the “Configure Input Network Feed” menu, and press Enter.

Use the Up and Down arrow keys to select the source of the input feed (eth0 or eth1).

Select the feed type, then press Enter. The different incoming stream types you can select are: unicast, multicast, or source-specific multicast (SSM).

If unicast was selected, use the Up and Down arrows to select the UDP port. Press Enter. Then use Up and Down arrows to select or deselect RTP mode.

If multicast was selected, specify the multicast address using the same procedure you used in Step 2. Once set, select the port and RTP mode as described under the unicast instructions above.

If SSM was selected, specify the multicast address, then specify the source IP address in the same manner. Once set, select the port and RTP mode as described above.

Configure Incoming Stream

16000 Horizon Way, Suite 500Mount Laurel, NJ 08054800.885.8886www.telvue.com/support

Toll Free: 800-885-8886Email: support@telvue.comSupport Portal: http://www.telvue.com/supportAPIs: http://www.telvue.com/apiTraining Videos: http://www.telvue.com/training

QSG_TC_7_13_V2

1Connect your video and audio outputs per the connection diagrams on the back page.

Connect Video & Audio Outputs

Ethernet [0] Ethernet [1]

4Press the Down arrow to access the menu.

1a.[ProVue Analog start here.] Use the Right arrow button to navigate to the “Set Output Configuration” menu, and press Enter. You will be prompted to choose between Composite, S-Video, Component, or HDMI. Continue to 1b.

1b. [ProVue SDI start here.] Use the Right arrow button to navigate to the “Set Output Format” menu.

2. The next screen will present a list of possible output formats, ranging from SD to HD, and are available in several different resolutions.

3. Scroll through the list using the Up and Down arrow keys until the desired format is found. Press the Enter key to complete the process.

Configure Output FormatTelVue ProVue™ LCD Screen

CANCEL ENTER

U s e D H C P ?y e s

CANCEL ENTER

N e t w o r k C o n f i gI P , S u b n e t , G W

CANCEL ENTER

S e t I P a d d r e s s1 9 2 . 1 6 8 . 1 . 1 2 7

IP ADDRESS ASSIGNMENT

DHCP – Dynamic Host Configuration ProtocolYour appliance will acquire an IP address from a DHCP server. This isn’t ideal for an appliance like your TelVue® server because your server may be assigned a new IP address unexpectedly, and it can be hard to determine what its current IP address is.

Static IPYou set an IP address during configuration and the appliance always uses that IP address. This is the preferred method because you always know what the IP address is. You will need an available IP address on your network, outside the DHCP range. Contact your IT department to get one. TelVue® recommends an IP address in the form 192.168.nnn.nnn, 172.nnn.nnn.nnn., or 10.nnn.nnn.nnn.

DHCP ReservationThe reservation tells your DHCP server to give your appliance the same IP address. This lets you use the simpler DHCP setup for your appliance, while still letting it use the same IP address. Refer to your DHCP server’s documentation to set up a reservation.

Getting StartedTelVue® ProVue™ SDI and Analog

QSG_TP_7_13_V2

What’s Next?We have many resources available to help you further and get you up and running faster! Solutions, documentation, literature, training videos and more are all at your fingertips. Check them out!

http://www.telvue.com/support/

http://www.telvue.com/support/training/

http://www.telvue.com/manual/provue

If you would like to set up an appointment for training please contact the TelVue® Support team at support@telvue.com.

16000 Horizon Way, Suite 500Mount Laurel, NJ 08054800.885.8886www.telvue.com/support

Toll Free: 800-885-8886Email: support@telvue.comSupport Portal: http://www.telvue.com/supportAPIs: http://www.telvue.com/apiTraining Videos: http://www.telvue.com/training

Breakout Cable

HDMI 4:2:2 Input

HDMI 4:2:2 Output

BNC Connector

Genlock

HD-SDI In

HD-SDI Out Deck Control - Not Used

TelVue ProVue™ SDI Video and Audio Output Connectors TelVue ProVue™ Analog Video and Audio Output Connectors

S-Video Connector

For S-Video out, connect the: • S-Video green connector to the breakout cable #4 Y Out green connector • S-Video blue connector to the breakout cable #5 B-Y Out blue connector

Analog VideoOutput - Y Out(For Composite)

Breakout Cable

Analog Video Input Y In

Analog Video Input R-Y In

Digital Audio OutputAES/EBU Out

Analog Video OutputB-Y Out

Analog Video InputB-Y InAnalog Audio Output

Audio Out RightAnalog Video

Output R-Y Out

Analog Audio Input Audio In Right

Analog Audio Output Audio Out Left

Analog Audio InputAudio In Left

14

1215 13

3

9

510

7

8

4