lab manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/manual/displacementsensorcd4_30.pdf1...
TRANSCRIPT
![Page 1: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/1.jpg)
1
Lab Manual
OPTEX-FA
LASER DISPLACMENT SENSOR
Laser Head CD4-L30 / Controller CD4A-LN / DBU-120A
Prepared by
Tran Ngoc Dang Khoa
ElectroMechanical Energy Laboratory
May 2016
![Page 2: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/2.jpg)
2
Contents
1. Objectives ................................................................................. 3
2. Instruments ................................................................................ 3
3. System ....................................................................................... 4
4. Overview of DBU-120A .......................................................... 4
5. Procedure .................................................................................. 8
![Page 3: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/3.jpg)
3
1. Objectives
1.1 This manual describes steps to measure vibration using laser displacement
sensor.
1.2 Understand the control parameters of monitoring software LK-Navigator 2,
and learn the techniques to measure vibration even for transparent materials,
at ultrasonic speed, in different unit scales (mm, µm).
2. Instruments
2.1 Laser head CD4-L30
2.2 Power supply 12VDC
![Page 4: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/4.jpg)
4
2.3 Controller CD4A-LN
2.4 Data acquisition system DBU-120A
2.1 Monitor software Measurement
![Page 5: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/5.jpg)
5
3. System
Figure 1: System connection
2.1 Connect system follow figure 1.
Figure 2: DBU-120A connection
![Page 6: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/6.jpg)
6
Output: GND
Output: Voltage
Input from laser head
Input from
power supply
Figure 3: Controller connection
2.2 Measurement is monitored from the computer by Measurement
software.
4. Overview of LK-Navigator 2
4. Procedures
Measurement is a software for configuring parameters and monitoring the DBU-120A
controller. It is used by connecting a computer and the controller to configure parameters
and monitor operating status.
Procedure steps:
1. Setup the instruments as the Figure 1 on page 5.
2. Start Measurement on the computer
![Page 7: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/7.jpg)
7
3. On the interface, click on Setup button
Setup
Channel of
connected
device
![Page 8: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/8.jpg)
8
4. On the set DB condition tab, setup value of parameters:
5. Check all 3 checkboxes on the top left of Set DB condition. And click OK.
6. Click Monitor button to read the weight value from sensor.
In no-load condition, click Balance button to offset the weight to zero.
![Page 9: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/9.jpg)
9
7. Set recording data file: save data file with the file name, and starting number of the
extensions (for multiple data files).
Monitor Balance Double-click
to set upper,
lower limit Sampling
frequency
Number
of data
![Page 10: Lab Manual - 中興大學教職員工網頁web.nchu.edu.tw/~daw/Manual/DisplacementsensorCD4_30.pdf1 Lab Manual OPTEX-FA LASER DISPLACMENT SENSOR Laser Head CD4-L30 / Controller CD4A-LN](https://reader036.vdocument.in/reader036/viewer/2022070108/6041de70e4d1f70e063394ee/html5/thumbnails/10.jpg)
10
8. An example of reading displacement value:
9. REMEMBER to safely remove DBU-120A device after using.