FTI-CDK2 Type 1A - Vehicle Coverage & Preparation Notes

Make Model Year Install I/O ChangesCAN Lights RAP Trunk

Park / Auto

Hey! Read this stuff before you start the installation...

Firmware:Covered vehicles require BLADE-AL(DL)-CH4 firmware, flash module and update the controller firmware before installing.

CAN:In the event that troubleshooting is necessary, CAN connections are in the connector at the WIN (Wireless Ignition Node)

Lights:Type A MUX type parking lights are populated in the supplied 6-pin headlight switch connectoron the harness assembly, properly secure the unused 10-pin connector for safety

RAP:Type F - RAP shutdown handling for all other covered vehicles is at the driver door pin wire, purple wire located in the driver kick panel harness, circuit tests ( - ) negative with door open

Okay, now get to work...

WINWIN

WINWINWINWINWIN

WIN

WINWINWINWINWINWIN

WIN

AA

AAAAA

A

AAAAAA

A

FF

FFFFF

F

FFFFFF

F

CM

-900

CM-900S/900AS

CM7X00

CM7000/7200

CM900AS/900S Jumper

SUPPORT - 1(888) 820-3690, EXT. 203

DL-CH4

ChryslerChrysler

DodgeDodgeDodgeDodgeDodge

Jeep

RAMRAMRAMRAMRAMRAM

VW

300Town & Country

ChallengerChargerGrand CaravanMagnumRAM

Grand Cherokee

C/V15002500350045005500

Routan

2008-102008-10

2008-142008-102008-102008-09

2009

2011-13

20102010-122010-122010-122010-122010-12

2009-10

Type 1Type 1

Type 1Type 1Type 1Type 1Type 1

Type 1

Type 1Type 1Type 1Type 1Type 1Type 1

Type 1

DEREK ZOOLANDER

Est.

2001

CENTER KIDS

WHO CAN’T READ GOOD

AND WHO WANNA LEARN TO DO OTH

ER

ST

UF

F G

OO

D T

OO

IIIIIIIII

III

IIIIII

IIIIII

IIIIII

IIIIII

IIIIII

IIIIII

IIIIIIII

IIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII

for

Cut loop for A/T

Green White/Blue

A B C D E

LED Programming Error CodesModule LED flashing RED during programming

1x - CAN issue2x - Immobilizer (confirm vehicle equipped, press button if not)3x - Immobilizer (confirm vehicle starts by key)4x - No VIN info5x - VIN mismatch (contact support)

12

SUPPORT - 1(888) 820-3690, EXT. 203

FTI-CDK2 Type 1A

Module Programming Procedure

1

2

PWRBLADE

Type AHeadlight Switch

Wireless Ignition Node

6

6

Type F ( - )

Driver kick panel harness

Purple ( - )E

W

AUTO

RE

AR

MW

A

D

E

Type B Parking light connections not required for this installation type. Please ensure that theunused connector is secured for safety

To provide control over vehicle Retained Accessory Power, configure controller POC forsetting #31 (RAP), see note for additional considerations.

Type F RAP control requires a connection to the purple wire originating at the driver doorpin, access is located in the driver kick panel harness

WTS (Wait to start) output from BLADE connector, connect to controller input for proper delayfor diesel vehicles. Properly insulate and secure if not used

E

FTI-CDK2 Type 1A - Installation Notes & Wiring Diagram

Step 1 - Wake BCM by closing then opening driver’s doorStep 2 - Activate IGN, module LED should turn redStep 3 - Wait for LED to begin rapidly flashing blueStep 4 - Remove key and press unlock on OEM key fob, if fob is unavailable/defective, press module button** IF BUTTON PRESS IS REQUIRED, KEYLESS CONTROL MAY REQUIRE ADDITIONAL PARTS OR WIRINGStep 5 - Programming complete when LED turns solid blue

A

D

*Not required

BLADE

CH4

WTS (+)

PRK MUX