manual tableros multimarca
DESCRIPTION
linea Alfa Romero datos de como solucionar varios inconvenientes de los tablerosTRANSCRIPT
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 1
Model 145/146 old version
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 2
Model 145/146 new version Model 156 Model 164 Delco Model 147
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 3
Model 166 Model 166/56 Model Spider & GTV Model 156 after 12/2001 < Update Juli 03
Model 145/146 old version
Remove the cluster and open it.
Look for the 68 pin prozessor by Magneti-Marelli.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 4
Connect the cables as shown in the picture.
Select the menu ALFA 145 - old. The Tacho Universal displays the old
value
Enter the new value. Verify the new value with OK.
Connect pin 57 (red cable) of the processor back to the circuit board.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 5
Model 145/146 new version
Use the Peugeot 406 cable:
The blue cable comes from the 4 cables that belong together, the green from the 2 data cables that belong together. The green marked pins have to be connected together. Hochlten=Lift pin Blaues Kabel=Blue cable Grn-Data Kabel=Green DATA-Cable - Verbinden=connect
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 6
Model 156
Use the Alfa 156 cable:
Blau=blue Grn=green
Schwarz=black Rot=red
1. Remove the cluster and open it.
2. Connect the black probe to the marked test-point.
3. Connect the cables as shown in the picture.
4. Select the menu ALFA 156. Tacho Universal displays the old value.
5. Enter the new value. Verify the new value with OK. Note: If the handheld stays very long at MOMENT when writing (over 2 minutes) please restart. Remove the programming plug from the handheld. Go to the Alfa 156 menue. Put the plug in the handheld and press as fast as possible OK. When the handheld has read the old value, remove the programming plug again. Enter the new value, put the plug back in and press immediately OK`.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 7
Troubleshooting TIP: Some times the 156 have problems with the electrical loading, try these steps to program it: 1. Dont connect the plug to the Tach 2. Go to the menu 156 3. connect the plug now 4. choose immediately 156 5. after reading disconnect the plug for 30 seconds, type in the new value 6. connect the plug and choose immediately writing you can try to connect the components of the cluster to Ground to eliminate the electrical loading
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 8
Model 156 after 12/2001
Use the Scorpio-cable:
Remove the cluster and open it.
Connect the marked points
Connect the cables as shown in the picture.
Select the menu ALFA 156. 2002-
The Tacho Universal displays the old value.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 9
Verbinden=connect Blau=blue Gelb=yellow Rot=red Schwarz=black
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 10
Model 164 Delco Use the Scorpio-cable:
Pin 1&2 brcken=connect Pin1&2 hochlten und blau=lift pin and blue cable Gelb=yellow Grne Wanne=green socket
Remove the cluster and open it.
Remove the complete circuit board. (somewhere on the board you can see the manufacturer. If it is Magneti Marelli you have to send us the instrument).
Connect the cables as shown in the picture
Join pin 1 + 2 at the processor with a screwdriver
Select the menu ALFA 164 Delco
The Tacho Universal shows you the old value. If it is not correct, you may
also have to lift the pin for the yellow cable.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 11
Model 166
Blu=blue Verde=green
1. Remove the cluster and open it.
2. Connect the cables as shown in the picture
3. Select the menu ALFA 166
4. The Tacho Universal displays the old value
5. Enter the new value.
6. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 12
Model 166/
Use this board and Clip :
Remove the cluster and open it.
Look for the 8 pin Chip 93C56.
Look for the silver crystal near the chip and join its contacts
Connect the clip to Port 1.
Put the clip on the Chip 93C56 (RED on Pin 1).
Select the menu Alfa-166 clip 56
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 13
Model 147
Use this board and Clip :
Remove the cluster and open it.
Look for the 8 pin Chip 93C86.
Look for the silver crystal near the chip and join its contacts
Connect the clip to Port 0.
Put the clip on the Chip 93C86 (RED on Pin 1).
Select the menu Alfa-147
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 14
Model Spider & GTV
Use the Spider/GTV- plug:
Processors marked 68HC705B16 cant be programmed with the Tacho Universal!!
Clean the processor
Disconnect pin 22 of the ZC422 187 CFN processor. Lift pin 10 of the IC HCT14A . Put the GTV plug onto the processor. Watch the pin 1 mark! Connect the power supply (red= +, black= -). Join the GTV plug to the Tacho Universal. Connect the Tacho Universal with the power supply. The old value is not displayed (????????). Enter the new value. When the Tacho Universal displays Reset press the red button on the
plug for less than 1 second.
After programming join pin 22 + 23 Re-connect pin 10.
-
Tacho Universal www.efichip.com
Tacho Universal Alfa Romeo page 15
Pin 10 hochlten=lift pin 10 - Pin 22 unterbrechen=disconnect Pin 22
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 1
Model A2, VDO Model A3 / S3 VDO up to Model 2000 Model A3 / S3 UKNSI Model A3 / S3 VDO after Model 2000 Cluster-plug Model A3 / S3 VDO after Model 2000 Clip Model VDO 2000 + 2001Diagnosis Model A3 / S3 Magneti Marelli after Model 2000 Model Magneti Marelli 2001Diagnosis Model A4 / S4 VDO up to Model 2000 Model A4 / S4 UK NSI Model A4 / S4 VDO after Model 2000 Cluster-plug Model A4 / S4 VDO after Model 2000 Clip Model A4 / S4 Magneti Marelli after Model 2000, Model A4 Bosch after Model 2001 Clip Model A4 Bosch after Model 2001 Soldering Model A4 Bosch Model 2000 up to 2001Diagnosis Audi A4 Bosch crypted after 09/01 Soldering Model Audi A4 Bosch crypted after 09/01 Clip Model A6 / S6, old Model C4, before 1997 Model A6 / S6 VDO, new Model up to Model 2000 Model A6 / S6 UK NSI Model A6 / S6 VDO after Model 2000 Cluster-plug Model A6 / S6 VDO after Model 2000 Clip Model A6 / S6 Magneti Marelli after Model 2000 Model A6,A3,A2 VDO after 06/2001 Model A8 / S8 up to ~ 1/1999 Model A8 / S8 after ~ 2/1999 Model TT up to Model 2000 Model TT after Model 2000
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 2
Model A2, VDO
Use this board and clip
Remove the cluster and open it.
Look for the 8 pin Chip 93C86.
Look for the silver chrystal and join its contacts.
Connect the clip to Port 0.
Put the clip on the Chip 93C86 (RED on Pin 1)
Select the menu Audi-A2 07.01- Clip
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 3
Model A3 / S3 VDO up to Model 2000
Diagnostic programming Use the OBD II -plug:
The diagnostic port is in the middle console of the car.
Turn ignition on.
Connect the Tacho Universal to the OBD II plug and the diagnostic port.
Select the menu AUDI-A3-VDO-Diagnosis
The Tacho Universal shows you the old value.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 4
Model A3 / S3 UKNSI
Use this board and clip:
Remove the cluster and open it.
Look for the silver chrystal and join its contacts.
Look for the 8 pin Chip 93C56 (not the chip 93C46!)
Connect the clip to Port 1.
Put the clip on the Chip 93C56 (RED on Pin 1).
Select the menu Audi-A3-UK NSI-Clip.
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 5
Model A3 / S3 VDO after Model 2000 Cluster-plug To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model.
Use this Cluster-plug:
Remove the cluster.
Connect the blue and the green plug to the instrument.
Select the menu Audi-A3-A3 2000-Diagnosis 2000.
The Tacho Universal shows you the old value.
Enter the new value.
Verify the new value with OK.
Note: If the displayed value is not correct, you can continue programming, most time it works anyway You cannot destroy anything. If you cannot change the value this way, you have to program by clip.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 6
Model A3 / S3 VDO after Model 2000 Clip To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model.
Use this board and clip:
1. Remove the cluster and open it.
2. Look for the 8 pin Chip 93C86.
3. Look for the silver chrystal and join its contacts.
4. Connect the clip to Port 0.
5. Put the clip on the Chip 93C86 (RED on Pin 1).
6. Select the menu Audi-A3-A3 2000- Clip 2000.
7. The Tacho Universal shows you the old value.
8. Select the menu Adjust KM.
9. Enter the new value.
10. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 7
Model A3 / S3 Magneti Marelli after Model 2000 To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model.
Use this Cluster-plug:
1. Remove the cluster and open it.
2. Connect the blue and the green plug to the instrument.
3. Also connect the black and the red cables like shown in the picture.
4. IMPORTANT: You must not move the black and the red contact when
beginning to read until you are ready with programming. A good contact is absolutely necessary.!!!
5. Select the menu Audi-A3-A3 2000-Magneti Marelli.
6. The Tacho Universal shows you the old value.
7. Enter the new value.
8. Verify the new value with OK.
Note: If the handheld shows you out of range the contact was bad or the database may be corrupted. For security reasons you cannot program the instrument at this moment. Normally it will be possible to program again after driving about 100 km.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 8
Model A4 / S4 VDO up to Model 2000
Diagnostic programming
Use the OBD II-plug:
The diagnostic port is in the back of the car in the ashtray.
Note: There are different instrument versions. To find the right one, you have to try which one gives you the right value when reading. Reading will not corrupt the database. But only program with the version that gives you the correct value!
Turn ignition on.
Connect the Tacho Universal to the OBD II plug and the diagnostic port.
Select the menu Audi-A4-VDO old- Diagnosis o or Audi-A4-VDO old MFA-Diagnosis o or Audi-A4-VDO new-Diagnosis
The Tacho Universal shows you with one of these programs the old value.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 9
Model A4 / S4 UK NSI
Use this board and clip:
Note: There are different instrument versions. To find the right one, you have to try which one gives you the right value when reading. Reading will not corrupt the database. But only program with the version that gives you the correct value!
Remove the cluster and open it.
Look for the silver chrystal and join its contacts.
Look for the 8 pin Chip 93C56 (not the chip 93C46!)
Connect the clip to Port 1.
Put the clip on the Chip 93C56 (RED on Pin 1).
Select the menu Audi-A4-UK NSI-UK NSI old
o or Audi A4-UK NSI- UK NSI new o or Audi A4-UK NSI-UK 2 Eeproms
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 10
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 11
Model A4 / S4 VDO after Model 2000 Cluster-plug To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model.
Use this Cluster-plug:
Remove the cluster. Connect the blue and the green plug to the instrument. Select the menu Audi-A4-A4 2000-Diagnosis 2000 The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK.
Note: If the displayed value is not correct, you can continue programming, most time it works anyway You cannot destroy anything. If you cannot change the value this way, you have to program by clip.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 12
Model A4 / S4 VDO after Model 2000 Clip To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model. Use this board and clip:
Remove the cluster and open it. Look for the 8 pin Chip 93C86.
Look for the silver chrystal and join its contacts.
Connect the clip to Port 0.
Put the clip on the Chip 93C86 (RED on Pin 1).
Select the menu Audi-A4-A4 2000- Clip 2000 The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 13
Model A4 / S4 Magneti Marelli after Model 2000 To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model. Use this Cluster-plug:
Remove the cluster and open it. Connect the blue and the green plug to the instrument. Also connect the black and the red cables like shown in the picture. IMPORTANT: You must not move the black and the red contact when
beginning to read until you are ready with programming. A good contact is absolutely necessary.
Select the menu Audi-A4-A4 2000-Magneti Marelli The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK. Note: If the handheld shows you out of range the contact was bad or the database may be corrupted. For security reasons you cannot program the instrument at this moment. Normally it will be possible to program again after driving about 100 km.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 14
Model A6 / S6, old Model C4, before 1997
Use those two plugs and connect them:
The diagnostic port is in the fuse box in the motorroom Turn ignition on. Connect the Tacho Universal with both plugs to the diagnostic port. Select the menu AUDI A6 A6 old - Diagnosis. The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK. Note: If you cannot read the old value or or nothing changes when programming, let the engine run. Maybe you have to try several times, also try different values, it will work.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 15
Model A6 / S6 VDO, new Model up to Model 2000
Diagnostic programming
Use the OBD II-plug
The diagnostic port near your left knee when you sit on the drivers seat. Turn ignition on. Connect the Tacho Universal to the OBD II plug and the diagnostic port Select the menu AUDI-A6-A6 new-Diagnosis The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 16
Model A6 / S6 UK NSI
Use this board and clip:
Remove the cluster and open it. Look for the silver chrystal and join its contacts. Look for the 8 pin Chip 93C56 (not the chip 93C46!). Connect the clip to Port 1. Put the clip on the Chip 93C56 (RED on Pin 1). Select the menu Audi-A6-UK NSI-Clip The Tacho Universal shows you the old value. Select the menu Adjust KM. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 17
Model A6 / S6 VDO after Model 2000 Cluster-plug To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model
Use this Cluster-plug:
Remove the cluster. Connect the blue and the green plug to the instrument. Select the menu Audi-A6-A6 2000-Diagnosis 2000 The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK.
Note: If the displayed value is not correct, you can continue programming, most time it works anyway You cannot destroy anything. If you cannot change the value this way, you have to program by clip.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 18
Model A6 / S6 VDO after Model 2000 Clip To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model
Use this board and clip:
1. Remove the cluster and open it.
2. Look for the 8 pin Chip 93C86.
3. Look for the silver chrystal and join its contacts.
4. Connect the clip to Port 0.
5. Put the clip on the den Chip 93C86 (RED on Pin 1).
6. Select the menu Audi-A6-A6 2000- Clip 2000
7. The Tacho Universal shows you the old value.
8. Select the menu Adjust KM.
9. Enter the new value.
10. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 19
Model A6 / S6 Magneti Marelli after Model 2000 To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model
Use this Cluster-plug:
Remove the cluster and open it. Connect the blue and the green plug to the instrument. Also connect the black and the red cables like shown in the picture. IMPORTANT: You must not move the black and the red contact when
beginning to read until you are ready with programming. A good contact is absolutely necessary.
Select the menu Audi-A6-A6 2000-Magneti Marelli The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK. Note: If the handheld shows you out of range the contact was bad or the database may be corrupted. For security reasons you cannot program the instrument at this moment. Normally it will be possible to program again after driving about 100 km.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 20
Model A6,A3,A2 VDO after 06/2001
Remove the cluster Connect the VAG-blue plug to the instrument Write down the original km-value Open the cluster, join the silver chrystal contacts, use Port 93CX6 Audi->A6(A3,A2)->A6 2002 VDO->VDO2002 R+W read and store. The Tacho Universal does not show you the old value. Remove the bridge at the silver chrystal, assemble the cluster and
clock it with the VAG-blue plug 40km (connect 100-300Hz on the blue cable of the VAG-blue plug)
Dont clock faster than 260 km/h. Power off, Power on and write down the second Km value. Open the cluster, join the silver chrystal contacts, use Port 93CX6 Audi->A6(A3,A2)->A6 2002 VDO->VDO2002 R+W read and store. The Tacho Universal does not show you the old value. Choose Audi->A6(A3,A2)->A6 2002 VDO->VDO2002 R+W and
choose the 2 datasets and type in the values. If the 2 datasets are correct the Tacho Universal will ask for the new
value. Write the now produced third dataset with the new value back on
the eeprom with VDO2002 R+W->Complete write (join the silver chrystal contacts again).
Ready
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 21
Model A8 / S8 up to ~ 1/1999
Diagnostic programming
Use the OBD II-plug:
The diagnostic port is under the ashtray. There is an old and a new version. The old version was built before 10/1996. If the program
shows you with the old version a wrong value, try the new version.( ???? is ok for the value then).
Turn ignition on. Connect the Tacho Universal to the OBD II plug and the diagnostic port. Select the menu Audi-A8-A8 old-Diagnosis
or Audi-A8-A8 new Diagnosis (different from year) The Tacho Universal shows you the old value. (for A8 new the value ????? is ok) Enter the new value. Verify the new value with OK. Note: If the new value is not displayed after programming, try this: Turn ignition off. Pull out the fuse for the odometer for a few seconds. (fuse Nr. 8 or 9 in the black line) Now the new value should be displayed
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 22
Model A8 / S8 after ~ 2/1999
Use this board and clip:
1. Remove the cluster and open it.
2. Look for the 8 pin Chip 24C17.
3. Connect the clip to Port 3.
4. Put the clip on Chip 24C17 (RED on Pin1).
5. Select the menu Audi A8 A8 24C17 V1
6. The Tacho Universal shows you the old value. (if not select the menu AUDI- A8-A8 24C17 V2).
7. Select the menu Adjust KM.
8. Enter the new value.
9. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 23
Model TT up to Model 2000
Diagnostic programming
Use the OBD II-plug:
The diagnostic port near your left knee when you sit on the drivers seat. Turn ignition on. Connect the Tacho Universal to the OBD II plug and the diagnostic port. Select the menu AUDI-Audi TT-TT Diagnosis Enter the new value. Verify the new value with OK. For some models you have to enter the old value on demand. Note: If you cannot change the value, the cluster is model 2000.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 24
Model TT after Model 2000
Use this Cluster-plug:
Remove the cluster and open it. Connect the blue and the green plug to the instrument. Also connect the black and the red cables like shown in the picture.
IMPORTANT: You must not move the black and the red contact when beginning to read until you are ready with programming. A good contact is absolutely necessary.
Select the menu Audi-Audi TT-TT 2000 The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK. Note: If the handheld shows you out of range the contact was bad or the database may be corrupted. For security reasons you cannot program the instrument at this moment. Normally it will be possible to program again after driving about 100 km.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 25
Model A4 Bosch after Model 2001 Clip
Use this board and clip:
Remove the cluster and open it.
Remove the needles
Look for the 8 pin Chip 24C08.
Connect the clip to Port 3.
Put the clip on the Chip 24C08 (RED on Pin 1).
Select the menu Audi-A4-A4 A4 24C08
The Tacho Universal shows you the old value. Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 26
Model A4 Bosch after Model 2001 Soldering
Use this board and clip SW 13
Remove the cluster and open it. Connect the cables as shown in the picture.
Connect the clip to Port 3.
Select the menu Audi-A4-A4 A4 24C08
The Tacho Universal shows you the old value. Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 27
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 28
Model A4 Bosch Model 2000 up to 2001Diagnosis
Use the OBD II-plug
The diagnostic port near your left knee when you sit on the drivers seat. Turn ignition on. Connect the Tacho Universal to the OBD II plug and the diagnostic port Select the menu AUDI-A4-2000-A4 Bosch Diag You have to type the start-address for the code-searcher: 0000 Now the Tacho Universal is searching for the code, it can take a while, the
progress is shown in %. If the Tacho Universal finds the code The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK.
Turn ignition off. Pull out the fuse for the odometer for a few seconds. Fuse Nr 15. Now the new value should be displayed
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 29
Model Magneti Marelli 2001Diagnosis
Use the OBD II-plug
The diagnostic port near your left knee when you sit on the drivers seat. Turn ignition on. Connect the Tacho Universal to the OBD II plug and the diagnostic port Select the menu AUDI-A3-A4-or-A6 2000-MagMar 07.2001- The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 30
Model VDO 2000 + 2001Diagnosis
Use the OBD II-plug
The diagnostic port near your left knee when you sit on the drivers seat. Turn ignition on. Connect the Tacho Universalto the OBD II plug and the diagnostic port Select the menu AUDI-A3-A4-orA6 2000-Diagnosis-2000 Obd The Tacho Universal shows you the old value. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 31
Audi A4 Bosch crypted after 09/01 Soldering
Use this board and clip SW 13
Audi A4 Bosch Crypted
Write down the original value.
Remove the cluster and open it.
Connect the cables as shown in the picture.
Connect the clip to Port 3.
Select the menu Audi-A4-Motometer Bosch 9/01
The Tacho Universal shows 0 km. Select the menu store.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
Enter now the old value and verify with OK.
The Tacho Universal shows the value that can be programed now
If this value is too high or too low, load the stored dataset and try again.
Select the menu Adjust KM.
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 32
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 33
-
Tacho Universal www.efichip.com
Tacho Universal Audi page 34
Model Audi A4 Bosch crypted after 09/01 Clip
Use this board and clip:
Write down the original value
Remove the cluster and open it.
Remove the needles Audi A4 Bosch crypted Look for the 8 pin Chip 24C08. Connect the clip to Port 3. Select the menu Audi-A4-Motometer Bosch 9/01 The Tacho Universal shows 0 km. Select the menu Store. Select the menu Adjust KM. Enter the new value. Verify the new value with OK. Enter now the old value and verify with OK. The Tacho Universal shows the value that can be programed now If this value is too high or too low, load the stored dataset and try again. Select the menu Adjust KM
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 1
Modell 3 series E36 up to Software 23 Modell 3 series E36 Software 24 Modell 3 series E36 Compact up to Software 7 Modell 3 series E36 Compact Software 20-23 Modell Z3 Roadster up to Software 7 Modell Z3 Roadster Sw 9 up to Sw 11 Modell Z8 Modell 3 series E46 up to Software 16 Modell 5 series E34 after 3/1989 Modell 5 series E39 low (instrument with 1 button) up to Software 16 Modell 5 series E39 high + IKE (Instrument with 2 buttons), up to ~ 11/1997 Modell 5 series E39 high - IKE after ~ 11/1997, Hardware 4,5,6, up to Software 12 Modell 5 series E39 high IKE (Instrument with 2 buttons) Software 13 Modell 5 series E39 high IKE (Instrument with 2 buttons) Software 13 Modell X5, high (Instrument with 2 buttons) IKE Software 13 Modell 5er/7er E39 low SW 9/10/11 Diagnosis Modell 7 series E32 after 3/1989 Modell 7 series E38 high + IKE (Instrument with 2 buttons), up to ~ 11/1997 Modell 7 series E38 high -, after ~ 11/1997, Hardware 4,5,6,bis Software 12 Modell 7 series E38 high IKE (Instrument with 2 buttons) Software 13 Modell 8er E31 Modell X5, high (Instrument with 2 buttons) IKE Software 13 All Models with M35080 Chip Method 1: new cluster Method 2: new Chip Programming EWS /LightModule(LKM) and keys 35080 Erase for the following clusters Modell Z3 SW 9 /10 Diagnosis < Update Juli 03 BMW Service
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 2
Modell 3 series E36 up to Software 23
Diagnostic programming
Use the BMW Diagnostic plug with the connector old:
The diagnostic port is in the motorroom under a round cap.
Turn ignition on.
Connect the Tacho Universal to the BMW diagnostic plug and the diagnostic port.
Select the menu BMW-3 series E36-Diagnosis
The Tacho Universal shows you the old value.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 3
Modell 3 series E36 Software 24
Remove the cluster.
Open it (pull the two parts of it away from each other).
On front of the board you can see the 8pin chip 93C46 or B58323. Remove the paint on it to get access to pin 1+2
Put the board back in the car and connect it with the plugs.
Connect pin 1+2 on the chip with a little screw-driver.
Turn ignition on and disconnect pin 1+2 after 1 second.
The display now shows , EEP 1 or Code N1. Connect the Tacho Universal to the BMW diagnostic plug and the diagnostic port.
Select the menu BMW-3 series E36-Diagnosis
The Tacho Universal shows you the old value.
Enter the new value.
Verify the new value with OK.
Turn ignition off.
Disconnect the board from the car. If you connect it again, the new value will be
displayed.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 4
Modell 3 series E36 Compact up to Software 7
Use this cluster-plug:
Remove the cluster.
Connect the plug with the blue port and put the 3 pin plug in the 4 pin
port left down on the instrument. Put this plug in as it is easy. If it is hart to position, it is upside down!
Select the menu BMW Z3/COMPACT Diagnosis The Tacho Universal does not show you the old value. Enter the new value. Verify the new value with OK.
If the Tacho Universal shows: remove plug, the programming was correct.
Otherwise control the position of the 3pin plug and try again.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 5
Modell 3 series E36 Compact Software 20-23
Use this cluster-plug:
Remove the cluster.
Connect the cluster plug with the white and blue port and the TachoUniversal
Select the menu BMW-3 series E36-Diagnosis
The Tacho Universal shows you the old value.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 6
Modell Z3 Roadster up to Software 7
Use this cluster-plug:
Remove the cluster. Connect the plug with the blue port and put the 3 pin plug in the 4 pin
port left down on the instrument. Put this plug in as it is easy. If it is hart to position, it is upside down!
Select the menu BMW Z3/COMPACT Diagnosis
The Tacho Universal does not show you the old value.
Enter the new value. Verify the new value with OK.
If the Tacho Universal shows: remove plug, the programming was correct.
Otherwise control the position of the 3pin plug and try again
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 7
Modell Z3 Roadster up to Software 7
Use this board and clip:
Remove the cluster. Remove the rear plastic cover. Look for the 8 pin Chip 93C46 Remove this chip from the board. Connect the clip to Port 1. Select the menu BMW-Z3/Compact -Innen The Tacho Universal shows you a wrong value Enter the new value. Verify the new value with OK. Take the code plug out. Put the code plug on port 1. The pins of the code plug are marked on the
bottom in the plastic. Pin 1 of the code plug must be positioned on pin 1 of the board.
Select the menu BMW-Z3/Compact-Aussen . The Tacho Universal shows you the old value. Select the menu Adjust KM. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 8
Modell Z3 Roadster Sw 9 up to Sw 11
Use this board and clip:
Remove the cluster. Remove the rear plastic cover. Look for the 8 pin Chip 93C56 Remove this chip from the board. Connect the clip to Port 1. Select the menu BMW-Z3/Compact SW 9-SW 11 -Innen The Tacho Universal shows you a wrong value Enter the new value. Verify the new value with OK. Take the code plug out. Put the code plug on port 1. The pins of the code plug are marked on the
bottom in the plastic. Pin 1 of the code plug must be positioned on pin 1 of the board.
Select the menu BMW-Z3/Compact-SW 9-SW 11-Aussen . The Tacho Universal shows you the old value. Select the menu Adjust KM. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 9
Modell Z8
Use this board and clip:
Remove the cluster. Remove the rear plastic cover.
Look for the 8 pin Chip 93C56
Connect the clip to Port 1.
Select the menu BMW-Z8
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 10
Modell 3 series E46 up to Software 16
Use this board and clip:
Remove the cluster. Remove the rear plastic cover. Take out the pins (clock and day-km) from the front . Remove all needles (against the clockwise direction) Clip off the display carefully. Now you can take off the circuit board. Look for the 8pin Chip B58 608 (=93C66) Look for the silver crystal near the chip and join its contacts Connect the clip to Port 2. Put the clip on the Chip B58 608 (RED on Pin 1). Select the menu BMW-3 series E46-Clip The Tacho Universal shows you the old value. If the value is not correct, try
Port 1 and Port 0. Select the menu Adjust KM. Enter the new value. Verify the new value with OK. Now select the menu BMW-3 series E46-Service The Tacho Universal may read a wrong value, if the car already has to be
serviced. Ignore it. Select the menu Adjust KM. Enter the new value that the service display is supposed to show. Verify the new value with OK. Assemble the cluster and watch for the correct standing of the needles
(when power is on the cluster they are moving up a bit)!
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 11
Modell 5 series E34 after 3/1989
Board for brown and blue Code-plug: Board for green Code-plug:
Remove the cluster. Look on the rear for a small plastic cover. Under it you can see a brown,
blue or green code plug. You have to break this cover to get the code plug out.
Take the code plug out. Put the brown or blue code plug on port 1. The pins of the code plug are
marked on the bottom in the plastic. Pin 1 of the code plug must be positioned on pin 1 of the board.
If the code plug is green, put it on the board BMW grn. There you can also see the shape of the code plug Put the plug carefully on the socket.
Select the menu BMW-5er/7er-blue o or BMW-5er/7er-brown o or BMW 5er/7er-green
The Tacho Universal shows you the old value. Select the menu Adjust KM. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 12
Modell 5 series E39 low (instrument with 1 button) up to Software 16
Diagnostic programming.
Use the BMW Diagnostic plug with the connector new:
The diagnostic port is in the motorroom under a round cap.
Turn ignition on.
Connect the Tacho Universal to the BMW diagnostic plug and the diagnostic port.
Select the menu Tacho Universal
BMW-5er/7er-E39 low- Diagnosis (up to Software 14) or BMW-5er/7er-E39 low- Diagnosis SW 15 (for Software 15) or BMW-5er/7er-E39 low- Diagnosis SW 16 (for Software 16)
The Tacho Universal does not show you the old value.
Enter the new value.
Verify the new value with OK.
If the value does not change, try again with the connector old.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 13
Modell 5 series E39 high + IKE (Instrument with 2 buttons), up to ~ 11/1997
Diagnostic programming.
Use the BMW Diagnostic plug with the connector new:
The diagnostic port is in the motorroom under a round cap.
Turn ignition on.
Connect the Tacho Universal to the BMW diagnostic plug and the
diagnostic port.
Select the menu BMW-5er/7er- E38/E38 high +IKE
The Tacho Universal does not show you the old value.
Enter the new value.
Verify the new value with OK.
If the value does not change, try again with the connector old.- If it still does not change, it may be a high IKE instrument. (2 Buttons, after ~ 11/1997).
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 14
Modell 5 series E39 high - IKE after ~ 11/1997, Hardware4,5,6 up to Software 12
Use this cluster-plug
Remove the cluster.
Connect the cluster plug with the white and blue port and the Tachouniversal. Ensure that the red point on each plug faces pin 1 on the instruments port.
Select the menu BMW-5er/7er-E38/E39 high IKE
The Tacho Universal shows you the hard- and softwareversion of the
instrument.
Enter the new value.
Verify the new value with OK.
The Tacho Universal asks after a while OK or UNDO
If you take a sharpe look at the display now, you can see the new value. If it is good, press OK, if not, you can undo everything with STOP
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 15
Modell 5 series E39 high IKE (Instrument with 2 buttons) Software 13
Use this board and cable:
Remove the cluster. Turn the cross-shaped plastic pins on the back in a not disturbing
position. Take the front away and remove all the Torx-screws. Remove the board with solving the lockings in the 3 plug-ports. Look for the points on the board you can see on the picture. Remove the
red paint that covers the contacts. Connect the cables as shown in the picture. Look for the silver crystal and join its contacts. Connect the clip to Port 2. Select the menu BMW-5er/7er-E38/39 high IKE-Clip SW13 The Tacho Universal shows you the old value. The Tacho Universal shows
you the old value, if it is wrong, go to Show. If the database is ok, you may continue. If not check the cables.
Select the menu Adjust KM. Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 16
Modell 7 series E32 after 3/1989
Brown and blue Code-plug: Board for green Code-plug:
Remove the cluster. Look on the rear for a small plastic cover. Under it you can see a brown,
blue or green code plug. You have to break this cover to get the code plug out.
Take the code plug out. Put the brown or blue code plug on port 1. The pins of the code plug are
marked on the bottom in the plastic. Pin 1 of the code plug must be positioned on pin 1 of the board.
If the code plug is green, put it on the board BMW green. There you can also see the shape of the code plug. Put the plug carefully on the socket.
Select the menu BMW-5er/7er-blue o or BMW-5er/7er-brown o or BMW 5er/7er-green
The Tacho Universal shows you the old value. Select the menu Adjust KM. Enter the new value. Verify the new value with OK.
Code-plug -brown
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 17
Modell 5 series E39 high IKE (Instrument with 2 buttons) Software 13
Use this board and cable:
Remove the cluster. Turn the cross-shaped plastic pins on the back in a not disturbing position.
Take the front away and remove all the Torx-screws.
Remove the board with solving the lockings in the 3 plug-ports.
Look for the points on the board you can see on the picture. Remove the red
paint that covers the contacts.
Connect the cables as shown in the picture.
Look for the silver crystal and join its contacts.
Connect the clip to Port 2.
Select the menu Tacho Universal : BMW-5er/7er-E38/39 high IKE-Clip SW13
The Tacho Universal shows you the old value. The Tacho Universal shows you the old value, if it is wrong, go to Show. If the database is ok, you may continue. If not check the cables.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 18
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 19
Modell 7 series E38 high + IKE (Instrument with 2 buttons), up to ~ 11/1997 Diagnostic programming.
Use the BMW Diagnostic plug with the connector new: The diagnostic port is in the motorroom under a round cap. Turn ignition on. Connect the Tacho Universal to the BMW diagnostic plug and the diagnostic
port. Select the menu Tacho Universal: BMW-5er/7er- E38/E38 high +IKE The Tacho Universal does not show you the old value. Enter the new value. Verify the new value with OK.
If the value does not change, try again with the connector old.- If it still does not change, it may be a high IKE instrument. (2 Buttons, after ~ 11/1997).
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 20
Modell 7 series E38 high -, after ~ 11/1997, Hardware 4,5,6,bis Software 12
Use this cluster-plug:
Remove the cluster.
Connect the cluster plug with the white and blue port and the TachoUniversal. Ensure that the red point on each plug faces pin 1 on the instruments port.
Select the menu BMW-5er/7er-E38/E39 high IKE
The Tacho Universal shows you the hard- and softwareversion of the
instrument.
Enter the new value.
Verify the new value with OK.
The Tacho Universal asks after a while OK or UNDO
If you take a sharpe look at the display now, you can see the new value. If it is good, press OK, if not, you can undo everything with STOP
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 21
Modell 7 series E38 high IKE (Instrument with 2 buttons) Software 13
Use this board and cable:
Remove the cluster. Turn the cross-shaped plastic pins on the back in a not disturbing
position.
Take the front away and remove all the Torx-screws.
Remove the board with solving the lockings in the 3 plug-ports.
Look for the points on the board you can see on the picture. Remove the red paint that covers the contacts.
Connect the cables as shown in the picture.
Look for the silver crystal and join its contacts.
Connect the clip to Port 2.
Select the menu BMW-5er/7er-E38/39 high IKE-Clip SW13
The Tacho Universal shows you the old value. The Tacho Universal shows
you the old value, if it is wrong, go to Show. If the database is ok, you may continue. If not check the cables.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 22
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 23
Modell 8er E31
Diagnostic programming.
Use the BMW Diagnostic plug with the connector old:
The diagnostic port is in the motorroom under a round cap.
Turn ignition on. Connect the Tacho Universal to the BMW diagnostic plug and the
diagnostic port.
Select the menu BMW-8er-Diagnosis
The Tacho Universal does not show you the old value.
Enter the new value.
Verify the new value with OK. . If the new value is not displayed, try to program again with open doors, open windows or any combination of it. If it still does not work, remove all plugs from the instrument. Close and lock the car for about 2 minutes. Open it, turn ignition on and program again. Put the instrument back in. Now it should be ok. If even this does not work, continue like this:
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 24
Use this board and clip:
Remove the cover under the steering wheel.
Take out the EKM-modul (looks like a video cassette).
Look for the 8 pin chip 93C56.
Put the clip on the chip 93C56 (RED on Pin 1).
Connect the clip to Port 2.
Select the menu BMW-8er-Clip
The Tacho Universal shows you the old value.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 25
Modell X5, high (Instrument with 2 buttons) IKE Software 13
Use this board and cable:
Remove the cluster. Turn the cross-shaped plastic pins on the back in a not disturbing
position.
Take the front away and remove all the Torx-screws.
Remove the board with solving the lockings in the 3 plug-ports.
Look for the points on the board you can see on the picture. Remove the red paint that covers the contacts.
Connect the cables as shown in the picture.
Look for the silver crystal and join its contacts.
Connect the clip to Port 2.
Select the menu Tacho Universal: BMW-5er/7er-E38/39 high IKE-Clip
SW13
The Tacho Universal shows you the old value. The Tacho Universal shows you the old value, if it is wrong, go to Show. If the database is ok, you may continue. If not check the cables.
Select the menu Adjust KM.
Enter the new value.
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 26
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 27
All Models with a M35080 Chip
Use this Board and the special clip: M35080
This chip is used in all E46, E38, E39 and X5 after Model 2001. The model 2001 you recognize by the new OBD II-socket in the car interior, instead of the BMW-typical round socket in the motorroom. This chip can be placed only upward, not downward. So there are two possibilities to set the wanted value:
You can buy a new cluster (with a new chip inside), if you put this cluster in a car he will get the original KM. This cluster will be counted from 0 to the wanted value. This happens about the plug 912
The original Chip M35080 will be replaced through a new one.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 28
Method 1: new cluster This proceeding is also for the other models, the program from the E46 is always used! Use the 912 plug:
Connect the cables with the original cluster as described in the plan:
Select the menu BMW-3 series E46- 35080- Tacho-->Tacho Universal The Tacho Universal stored the original Dataset, confirm with a key. Connect the new cluster as described in the plan Select the menu BMW-3 series E46-35080- Tacho--> Tacho universal. Now you see a list of stored datasets. Load the newest one. Now the cluster is new coded. Select the menu BMW-3 series E46-35080- Clock
Type in the new value. The KM are now counting upward, this can take a while. Please supervise the actual value.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 29
Grn: green - Gelb: yellow - Schwarz: black - Weiss: white
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 30
Methode 2: new chip
Use the M35080 board and clip:
Connect the clip to Port M35080. Put the clip on the original removed M35080 (RED on Pin 1). Select the menu BMW-3 series E46-35080-Clip The Tacho Universal shows you the old value. Store the dataset. Set the clip on the new 35080 Chip. Select the menu Load. Choose the newest dataset and write it with complete Writing on the new chip,
this can take a while. The Error-Message Data unequal you can ignore Select the menu Adjust KM. Enter the new value. Verify the new value with OK. Put the new chip back on the board.
Important: Do not programm values less than 300km!!!
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 31
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 32
E38/39 High after Sw14 E39 Low after Sw17 1. The marked spring is mobile on the axle and very sensitively. 2. Lock the axle between the spring and the circuit board. You can do it
very strong, the axle is very stable. 3. Use a sheet of paper to save the cluster-foil for scratches. Then you
can remove the needles. 4. The economy-needle can be removed with the special remover. You
have to remove the cover first.
E38/39 High after Sw14 E39 Low after Sw17 1. The Eeprom M35080 is on the rear side of the board. Remove this chip. Put the clip on the original removed M35080 (RED on Pin 1). Select the menu BMW-3 series E46-35080-Clip The Tacho Universal shows you the old value. Store the dataset. Set the clip on the new 35080 Chip. Select the menu Load. Choose the newest dataset and write it with complete Writing on the new chip, this can take a while. The Error-Message Data unequal you can ignore Select the menu Adjust KM. Enter the new value. Verify the new value with OK. Put the new chip back on the board and store the original chip. 2. After the programming set the pointer in the right position, this is 1 mm
behind the stopper. Test that the pointers are going to the 0-position. Never program less than 300 km
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 33
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 34
Modell 5er/7er E39 Low SW 9/10/11 Diagnosis
Remove the cluster.
Connect the Plug with the black and the white socket at the cluster.
Select the menu BMW 5er/7er E39 Low Diagnosis
The Tacho Universal does not show you the old value.
Enter the new value.
Verify the new value with OK.
Grn: green - Gelb: yellow - Schwarz: black - Weiss: white
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 35
Programming EWS /Light-Module(LKM) and keys
m LKM 3 series LKM 5 series
EWS
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 36
Remove first the EWS (ignition lock) (driver floor space behind the cover), then the LKM (front seat passenger side on the A-column) and then the cluster. First erase the EWS, then the keys, program the LKM and then the instrument. Put the modules back in the car: First the EWS, then the LKM and the cluster. REMEMBER to check for the RED pin of the EWS.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 37
Hochlten & Gelb: lift pin & yellow cable Hochlten & Blau: lift pin & blue cable
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 38
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 39
Hochlten & Gelb: lift pin & yellow cable Hochlten & Blau: lift pin & blue cable
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 40
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 41
Kurz auf Masse wenn Auslesen nicht mglich: Put it on Minus if you get no value Hochlten & Gelb: lift pin & yellow cable - Hochlten & Blau: lift pin & blue cable
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 42
If you cant read out the value, connect a 1KOhm resistor to the brown marked point, choose V3 and before you press OK hold the resistor on Minus(-)
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 43
If you get no value connect the blue (blau) and the yellow (gelb) cable directly to the lifted pins of the processor (like the E46LKM)
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 44
If you get no value, connect the marked point with a 1,5KOhm resistor before the reading shortly to the ring of the the power supply of the Tacho Universal (screw 3,5mm on the right side) Gelb DATA: yellow DATA - Blau DATA: blue DATA
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 45
35080 Erase for the following clusters
Use this board and cable BMW sw13
1. Remove the cluster. 2. Remove the rear plastic cover 3. Connect the Sw13 Kabel as described in the picture. 4. Connect the cable BMW Sw13 on Port M35080 5. Select the menu 3 series E46/35080 Clip 6. The Tacho Universal shows you the old value. 7. Select the menu store OK
350080 Erase 1. Select the menu 3 series E46/35080 /35080->0 2. Please wait until OK is on the Tacho Universal
35080 program on new value
1. Select the menu 3 series E46/35080 Clip 2. Select the menu Load. 3. Choose the newest dataset and write it with complete Writing on the
new chip, this can take a while 4. The Error-Message Data unequal you can ignore 5. Select the menu Adjust KM. 6. Enter the new value. 7. Verify the new value with OK.
Ready
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 46
read the dataset with M35080 and store it set the M35080 to 0 Write the stored dataset with complete writing back Program the km with Adjust KM
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 47
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 48
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 49
BMW Service
BMW old models with the round Diagnosticport
rcksetzen For all BMW`s with the BMW Diagnosticport (not OBD-II) 1. Take a stell wire. 2. Turn ignition on, dont start the engine. 3. Connect the contacts with the wire, wait (3 or 12 seconds) then disconnect the wire. Hint: The time must be exactly, otherwise no success, try again. Reset-Contacts: 19 and 7 To reset the LED for Oilservice ~ 3 seconds connect. To reset the LED for inspection ~ 12 seconds connect.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 50
BMW new models with OBD Diagnostic-port
Turn ignition off press left button and hold - ignition on position 1 Hold the left button till 5 seconds after Test 1 then Oilservice or Inspection is displayed. Press again the left button to reset the service, if you press not long enough, the brake fluid interval will be displayed, you can press left to reset it.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 51
Modell Z3 SW 9 /10 Diagnosis
Remove the cluster. Connect the cable 912 with the cluster ports as described in the picture
Select the menu BMW Z3/COMPACT/SW 9 Diagnosis
The Tacho Universal shows ?????? value
Enter the new value. Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 52
-
Tacho Universal www.efichip.com
Tacho Universal BMW page 53
Modell Z4
Use the M35080 clip and this board:
-
Tacho Universal www.efichip.com
Tacho Universal Cadillac page1
Cadillac
Modell Seville STS
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 1
Model Voyager up to Model 1998 Model Voyager after Model 1999 Model Grand Cherokee up to 5/1999 Model Stratus up to Model 1998 Model Stratus after Model 1999
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 2
Model Jeep Cherokee Model Jeep Wrangler Model PT Cruiser Model PT Cruiser 2002 Model Voyager 2002 Model Grand Cherokee 2002 Model Neon Model Cherokee 2002 Model Cherokee 2003 < Update Juli 03 All Chrysler Models SRI-Memory Model Voyager up to Model 1998
Chrysler-Diagnostic-plug:
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 3
The diagnostic port is near your left knee when you sit on the drivers seat.
Turn ignition on.
Connect the Tacho Universal to Chrysler diagnostic plug and the
diagnostic port. Use the connector CCD
Select the menu Chrysler-Chrysler Diagnose.
The Tacho Universal shows you the old value. A deviation of 1000 km is normal.
Enter the new value
Verify the new value with OK.
Note: If the new value is not displayed, you have to disconnect the battery for about 2 minutes.Important: Radiocode! (last page in the manual)
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 4
Model Voyager 2002
Use the 912-Plug
Remove the Bodycontroller.
Connect the cables as shown in the picture
Select the menu Chrysler-Voyager 912
The Tacho Universal shows you the old value.
Enter the new value
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 5
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 6
Model Voyager after Model 1999 Chrysler-Diagnostic-plug: Diagnostic-plug
The diagnostic port is near your left knee when you sit on the drivers seat.
Turn ignition on.
Connect the Tacho Universal to Chrysler diagnostic plug and the
diagnostic port. Use the connector CCD
Select the menu Chrysler-Chrysler99 Diagnose.
The Tacho Universal shows you the old value. A deviation of 1000 km is normal.
Enter the new value
Verify the new value with OK.
Note: If the new value is not displayed, you have to disconnect the battery for about 2 minutes. Important: Radiocode (last page in the manual)
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 7
Model Grand Cherokee up to 5/1999
Chrysler-Diagnostic-plug: Diagnostic-plug
1. The diagnostic port is near your left knee when you sit on the drivers seat.
2. Turn ignition on.
3. Connect the Tacho Universal to Chrysler diagnostic plug and the
diagnostic port. Use the connector CCD
4. Select the menu Chrysler-Chrysler Diagnose.
5. The Tacho Universal shows you the old value. A deviation of 1000 km is normal.
6. Enter the new value
7. Verify the new value with OK.
Note: If the new value is not displayed, you have to disconnect the battery for about 2 minutes.Important: Radiocode (last page in the manual)
-
Tacho Universa www.efichip.com
Tacho Universal Chrysler page 8
Model Stratus up to Model 1998 Chrysler-Diagnostic-plug: Diagnostic-plug
The diagnostic port is near your left knee when you sit on the drivers seat.
Turn ignition on.
Connect the Tacho Universal to Chrysler diagnostic plug and the
diagnostic port. Use the connector CCD
Select the menu Chrysler-Chrysler Diagnose.
The Tacho Universal shows you the old value. A deviation of 1000 km is normal.
Enter the new value
Verify the new value with OK.
Note: If the new value is not displayed, you have to disconnect the battery for about 2 minutes.Important: Radiocode (last page in the manual)
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 9
Model Stratus after Model 1999 Chrysler-Diagnostic-plug: Diagnostic-plug
The diagnostic port is near your left knee when you sit on the drivers seat.
Turn ignition on.
Connect the Tacho Universal to Chrysler diagnostic plug and the
diagnostic port. Use the connector CCD
Select the menu Chrysler-Chrysler99 Diagnose.
The Tacho Universal shows you the old value. A deviation of 1000 km is normal.
Enter the new value
Verify the new value with OK.
Note: If the new value is not displayed, you have to disconnect the battery for about 2 minutes.Important: Radiocode (last page in the manual)
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 10
Model Jeep Cherokee
Use this board and plug:
Remove the cluster and open it.
Connect the clip to Port 2.
Put the clip on the Chip 93C56 (rot auf Pin 1).
Select the menu Chrysler-Jeep Cherokee
The Tacho Universal shows you the old value. If the value is not correct, try Port 1 and Port 0.
Select the menu Adjust KM
Enter the new value
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 11
Model Jeep Wrangler
Use this board and plug:
Remove the cluster and open it.
Connect the clip to Port 2.
Put the clip on the Chip 93C56 (rot auf Pin 1).
Select the menu Chrysler-Jeep Wrangler
The Tacho Universal shows you the old value. If the value is not correct, try Port 1 and Port 0.
Select the menu Adjust KM
Enter the new value
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 12
Model PT Cruiser
Remove the cluster and open it.
Remove the motors with the needles from behind with the soldering iron.
Connect the cables as shown in the picture
Select the menu Chrysler-PT Cruiser
The Tacho Universal shows you the old value.
Enter the new value
Verify the new value with OK.
Use the Scorpio-Plug:
Hochlten=Lift pin Schwarz=black Gelb=yellow Blau=blue Rot=red
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 13
Model PT Cruiser 2002
Use the 912-Plug
Remove the cluster and open it.
Remove the motors with the needles from behind with the soldering iron.
Connect the cables as shown in the picture
Select the menu Chrysler-PT Cruiser 912
The Tacho Universal shows you the old value.
Enter the new value
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 14
change the silver crystal to a 4 Mhz Type Rot=red Schwarz=black
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 15
Model Grand Cherokee 2002
Use the 912-Plug
Remove the cluster and open it.
Connect the cables as shown in the picture
Select the menu Chrysler-Grand Cherokee 912
The Tacho Universal shows you the old value.
Enter the new value
Verify the new value with OK.
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 16
change the silver Cut the tracks here and to a 4 Mhz type connect after programming
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 17
All Chrysler Models SRI-Memory Chrysler-Diagnostic-plug: Diagnostic-plug
1. The diagnostic port is near your left knee when you sit on the drivers seat.
2. Turn ignition on.
3. Connect the Tacho Universal to Chrysler diagnostic plug and the
diagnostic port. Use the connector SRI.
4. Select the menu Chrysler-Chrysler SRI
5. The Tacho Universal shows you the old value, it can also be stored in miles. Then you have to convert the miles.
6. Enter the new value
7. Verify the new value with OK.
Note: You dont need to program the memory, if the Tacho Universal reads 000000 as old value!
-
Tacho Universal www.efichip.com
Tacho Universal Chrysler page 18
Model Neon
Use the S