manual to update to r-nethandicare.blob.core.windows.net/media/...til-r-net-levo-combi-englis… ·...

Man

To change the Pilot+ control Step 1: Bring the chair into seating ptwo screws (red arrows). Step 2: Bring the chair into standing the main fuse/switch.

ual to change the control from Pilot+ to R-net

to the R-net control you need around 2

position and take off the rear cover plat

position and raise the lift to the top po

2 hours.

te. Untighten the

osition. Switch off

Man

Step 3: Remove the Pilot+ joystick, funtighten the screws (red ar Step 4: Remove the joystick cable, c Step 5: Remove the plugs from the l


first plug out the joystick cable (green arow).

ut the cable tie’s (red arrows).

imit switches on the back.

arrow), then

Man

Step 6: Remove the plugs from the l Step 7: Cut all cable ties (red arrows


imit switch ES20.

s) from the cable harness under the seaat plate.

Man

Step 8: Open the cable conduit and r Step 9: Open the battery cover and sRemove the plate with the lim Step 10: Put the limit switch plate on with the battery-pins. Open t


remove the cable harness.

secure the cover with a cable tie that itmit switches by untighten the 4 screws

the batteries, but take care that they dthe ALM-box by untighten the 2 screws

t stays open. (red arrows).

don’t make contact s (red arrows).

Man

Step 11: Remove all the cables from t Step 12: Remove the cables from the plugs, press on top of the pocable plug. Then remove the


the ALM-box, then remove the whole AL

Power Module, take care with the poweower cable plug to remove it and on the Power Module

LM-box.

er and the motor e side of the motor

Man

Step 13: Remove the jacks from the gframe. Step 13b: If you have light, you also necables. First you need to remThen open the lights and indout all the light cables.


grey limit switches (red arrows) at the f

eed to update this with new cables. Remmove the cable bushing at the front of ticators and unplug the cables. Cut the

front of the basic

move the old he basic frame. cable ties and take

Man

Step 14: Change the grey limit switch Step 15: Mount the bushings of the grbit easier if you remove the b Step 15b: If you have light on the chair

Seat


es on the plate to the new version.

rey limit switches on the front of the babatteries. Then plug in the actuators.

r, mount the light cables on the front

Seat

Back

Seat

Lift

Lift

asic frame. It is a

Back

Lift

Back

Man

Step 16: Screw the ISM and the new P Step 17: Put the plate with the Power Velcro (hook-and-loop fastenconnect the ISM and the Pow


Power Module on the support plate.

Module and the ISM in the basic framener). Then plug in the power and the mwer Module.

M5x20

M5x12

e and mount the otor cables and

Man

Step 18: Connect the grey limit switch Step 19: Plug in the joystick cable andPower Module and ISM.

Backrest (B) jack no. 1

Seat (S) jack no. 2

ES 22/23

Joystick cable


hes to the ISM:

d connect the cables from the other lim

Lift (L) jack no. 3

ES 20

it switches to the

ES 2/3

Man

Step 19b If you have light you also ne Step 20: Mount the blue tilt switch to the limit switch plate and the

Light left

Light right

M3x15


ed to plug in the light cables.

the tilt switch support. And mount the e welded block.

It canswitchin thathe su

Take care that the cable of the tilt switch is facing backwards, otherwise it won’t

work correct.

support between

n be that the tilt h reacts too fast, at case just bend upport a bit more to the top.

Man

Step 21: Put some order to the cablesarrows). Step 22: Put the cable harness into thon the cable conduit. Step 23: Put the cable guard over the


s and tighten them with cable ties to the

e cable conduit and put the cable cond

cable harness and close the cable cond

Shift the c

e motor cables (red

uit cover halfway

duit.

cover to the front

Man

Step 24: Mount the cable harness withplate. Step 25: Mount the plugs of ES20 and

1


h some cable ties (red arrows) to the re

d fix it with cable ties (green arrows).

3

2

ear of the seat

Man

Step 26: Mount the plugs of ES 2/3 anarrows). left side ES 2/3 Step 27: Mount the joystick holder to

1

2


nd ES 22/23 and tighten the cables with

right side

the joystick.

3

4

M5x8

h cable ties (green

ES 22/23

2

1

Man

Step 28: Mount the joystick to the braties (green arrows). Step 29: The chair should work now. Gjoystick cable with a cable tieposition and tighten the cabl

M6x16


acket on the armrest and fix the joystic

Go into the lowest seating position and e to the seat plate (green arrow). Thene to the limit switch cable.

k cable with cable

tighten the go into standing

Man

Step 30: If you have light, you just nethe guiding on the front of thon the left and on the right h Then put the light cables throbulbs. Now you can mount th


eed to finish the mounting of the light che basic frame (red arrow), and throughhand side of the basic frame (green arro

ough the light holders and mount the hhe light covers.

cables. Go through h the two guidings ow).

holders with the

manual to update to r-nethandicare.blob.core.windows.net/media/...til-r-net-levo-combi-englis… ·...

Documents