m.calculo tapa 1406-03-500gl

Upload: percyalexander

Post on 02-Jun-2018

216 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/11/2019 M.calculo Tapa 1406-03-500GL

    1/1

    2

    3

    4

    6

    7

    8 Dimensions:9 37.441 951 mm Do [in]- Dimetro exterior de la tapa

    10 18.720 475.5 mm L [in]- Radio interior curva (nota 1)

    11 1.969 50 mm IKR [in]- radio interior menor (nota 2)

    12 0.118 3 mm tb [in]- espesor despues de conformado

    13 0.118 3 mm tf [in]- espesor antes de conformado (nota 3)

    14 0.039 1 mm Corr [in]- factor de corrosion

    15 1.772 45 mm Skirt [in]- longitud pestaa

    16 Condicio nes del Mater ia l:

    17 A-36 Material

    18 16,600 S [psi]- Esfuerzo

    19 0.85 E - Eficiencia long. Tapa

    20 25.0 P [psi]- Presin interior21 Calculo Propiedades:22 nota 1: Radio sugerido L por UG-32(j) 37.44 Peso Aprox. Tapa basado en Acero, lbs = 90.2223 nota 2: Radio sugerido IKR por UG-32(j) 2.246 Volumen Aprox. Tapa incluyendo pestaa, cuft = 7.8124 nota 3: Espesor sugerido antes conformado 0.0861

    25 Variables:

    26 nt [in]= tf-Corr ~~thickness with corrosion allowance removed 0.118-0.039 = 0.079

    27 D [in]= Do-2*nt ~~ID with corrosion allowance removed 37.441-2*0.079 = 37.283

    28 L/r = L/IKR 18.72/1.969 = 9.510

    29 M = 0.25*(3+sqrt(L/IKR)) 0.25*(3+SQRT(18.72/1.969)) = 1.521

    30 Ro [in]= L+tb 18.72+0.118 = 18.839

    31 Espesor Requer ido:App. 1-4(a), App. 1-4(d)

    32

    App1-4(f) = tf/L 0.118/18.72 = 0.00633 App1-4(f)Calc =

    34 App. 1-4(f) Calculation Not Required

    35 T.req [in]=

    36 0.065

    37 Verif. Esp.T req = Treq= 25 = Acceptable

    42 App. 1-4(f) calculation is not included on this sheet

    43 Nozzles may be subject to a smaller required thickness depending on location in the head.

    44 Only the knuckle required thickness is calculated on this sheet

    45 Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UG-37(a)(1)46 The UG-16(b) minimum thickness requirement has not been taken into consideration here. Fecha: jun-1447 This sheet cannot be used to check for allowable exterior pressure loads. Revisado por: Roberto A anca48 Use the Weld Efficiency program to calculate E

    49 This sheet is for educational use only - use at your own risk.

    50

    51

    52

    53

    if(AND(0.0005=