me 6405 student lecture transistor
DESCRIPTION
ME 6405 Student Lecture Transistor. Sung-bum Kang Keun Jae Kim Hongchul Sohn Wenwei Xu October 1, 2009 Georgia Institute of Technology. Contents. 1. Introduction to Transistor (Speaker: Sung-bum Kang). 2. Bipolar Junction Transistor (Speaker: Keun Jae Kim). 3. Field Effect Transistor - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/1.jpg)
ME 6405 Student Lecture
Transistor
Sung-bum Kang
Keun Jae Kim Hongchul Sohn
Wenwei Xu
October 1, 2009
Georgia Institute of Technology
![Page 2: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/2.jpg)
Contents
Introduction to Transistor(Speaker: Sung-bum Kang)
Field Effect Transistor(Speaker: Hongchul Sohn)
Power Transistor(Speaker: Wenwei Xu)
11
33
44
Applications of Transistor(Speaker: Wenwei Xu)55
Bipolar Junction Transistor(Speaker: Keun Jae Kim)22
![Page 3: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/3.jpg)
“Transistor” Part 1
Introduction to Transistor(Speaker: Sung-bum Kang)11
Field Effect Transistor(Speaker: Hongchul Sohn)
Power Transistor(Speaker: Wenwei Xu)
33
44
Applications of Transistor(Speaker: Wenwei Xu)55
Bipolar Junction Transistor(Speaker: Keun Jae Kim)22
![Page 4: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/4.jpg)
Introduction
Question #1: How can we transfer original signal in long distance without loss?
Amplifier and Electronic Switch are needed.
Amplifier: any device that changes, usually increases, the amplitude of a signal. Electronic Switch: switch that the physical opening and closing is achieved by
applying appropriate electrical control signals.
Question #2: How can we control the TV with remote-controller?
Question #3: How can a computer recognize 0(off) and 1(on) for computing?
![Page 5: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/5.jpg)
Introduction
Early 20th century, vacuum tube was used for the amplifier and switch.
ENIAC, the first general-purpose electronic
computer, contains 17,468 vacuum tubes.Vacuum Tube Radio
However, Vacuum Tube is too big, fragile, and energy-consuming.
Transistor solved this problem.
![Page 6: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/6.jpg)
Introduction – Invention of Transistor
Invention In 1947, John Bardeen, Walter Brattain,
and William Schockly, researchers at Bell Lab, invented Transistor.
They found Transistor Effect: “when electrical contacts were applied to a crystal of germanium, the output power was larger than the input.”
In 1956, they were awarded the Nobel Prize in physics.
Transistor is a semiconductor device commonly
used to amplify or switch electronic signals.
John Bardeen, Walter Brattain,
and William Schockly
First model of Transistor, 1947
![Page 7: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/7.jpg)
Introduction – Progress of Transistor
more than 2.9 billion transistors is packed into an area of fingernail
1941, Vacuum Tube
1948, the first (Germanium) TR
1954, Silicon TR
1958, Integrated Circuit
Sep 2009, 22nm silicon wafer
Now?
Edison effect
John Bardeen, Walter Brattain, and William Schockly
At TI Lab, Ease of processing, lower cost, greater power handling, more stable temperature characteristics
Intel CEO Paul Otellini, Sep 23 2009
Individual electronic components were soldered on to printed circuit boards.
IC placed all components in one chip.
![Page 8: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/8.jpg)
Introduction – Underlying Science
Semiconductor is a basic building material of most integrated circuits. is a material that has an electrical resistivity between that of a
conductor and an insulator. has a few charge carriers(holes or free electrons) and may hence
be classified as almost insulator. However, the conductivity increases by adding impurities(doping).
Silicon is used in most commercial
semiconductors
![Page 9: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/9.jpg)
Introduction – Underlying Science
Doping P(positive)-type doping is adding a certain type of atoms to the
semiconductor in order to increase holes. P-type semiconductor, acceptor
N(negative)-type doping is adding some amount of an element with more electrons in order to increase free electrons.
N-type semiconductor, donor
Add Group III(Boron)Add Group V (Phosphorous)
![Page 10: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/10.jpg)
Introduction – Underlying Science
PN Junction is a junction formed by P-type and
N-type semiconductors together in very close contact.
Electrons(+) from n(-) region diffuse to occupy holes(-) in p(+) region.
Thin depletion region forms near junction.
What happens at the junction?
![Page 11: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/11.jpg)
Introduction – Underlying Science
Forward bias -V pumps electrons into the N-region. +V pumps more holes into the P-region. Excess of charge in P and N region will
apply pressure on the depletion region and will make it shrink.
→ current flows
Backward bias -V sucked out electrons from N-region. +V sucked out holes from P-region. The depletion layer widens and it
occupies the entire diode(p-n). → current doesn’t flow
External Energy
![Page 12: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/12.jpg)
Introduction – Types of Transistor
Transistor are categorized by Semiconductor material: germanium, silicon, gallium arsenide, etc.
Structure: BJT, FET, IGFET (MOSFET), IGBT
Polarity: NPN, PNP (BJTs); N-channel, P-channel (FETs)
Maximum power rating: low, medium, high
Maximum operating frequency: low, medium, high
Application: switch, audio, high voltage, etc.
Physical packaging: through hole, surface mount, ball grid array, etc.
Amplification factor Various Types of Transistor:
http://en.wikipedia.org/wiki/Category:Transistor_types
General Purpose Transistors Bipolar Junction Transistor (BJT) Field Effect Transistors (FET) Power Transistors
![Page 13: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/13.jpg)
“Transistor” Part 2
Field Effect Transistor(Speaker: Hongchul Sohn)
Power Transistor(Speaker: Wenwei Xu)
33
44
Applications of Transistor(Speaker: Wenwei Xu)55
Bipolar Junction Transistor(Speaker: Keun Jae Kim)
Introduction to Transistor(Speaker: Sung-bum Kang)11
22
![Page 14: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/14.jpg)
BJT Introduction
PNP
NPN 3 Terminals
Base (B) Collector (C) Emitter (E)
2 Types: NPN, PNP Currents flow in opposite
direction NPN:
BE forward biased BC reverse biased
PNP: BE reverse biased BC forward biased
![Page 15: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/15.jpg)
Georgia Institute of Technology 15
BJT Characteristics
IC is controlled by IB (Current Control) β (beta) is amplification factor for
transistor Typical value of is β 20 ~ 200
iE = iC + iB iC = βiB
VBE = VB – VE
VCE = VC - VE
![Page 16: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/16.jpg)
Operating Regions
BJT Operating Regions
![Page 17: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/17.jpg)
Operating Regions
Operating Region
Parameters Mode
Cut OffVBE < Vcut-in VCE > Vsupply
IB = IC = 0Switch OFF
LinearVBE = Vcut-in
Vsat < VCE < Vsupply
IC = β*IB
Amplification
Saturated
VBE = Vcut-in,VCE < Vsat
IB > IC,max, IC,max > 0
Switch ON
BJT Operating Regions
![Page 18: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/18.jpg)
Georgia Institute of Technology 18
1) Cutoff Region: VBE < Vcut-in, iB = 0 iC = 0, VCE > Vsupply
2) Active / Linear Region: VBE = Vcut-in, iB > 0 iC = βiB, Vsat < VCE < Vsupply
3) Saturation Region: VBE = Vcut-in, iB > iC,max iC,max, VCE < Vsat
Vin
Vsupply
BJT Operating Regions
![Page 19: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/19.jpg)
VSupplyVin
RB
RC
Question: What is the minimum Vin that can use the transistor as an amplifier?
Given:• RB = 10 kΩ• RC = 1 kΩ • β = 100• VSupply = 10 V• Vcut-in = 0.7 V• Vsat = 0.2 V
iB = iC / β = 0.0098/100 = 0.098mA
BJT as Amplifier
Vin - iB*RB – VBE = 0
Vsupply – iC *RC – VCE=0
iC = (Vsupply – VCE) / RC
Set VCE = Vsat = 0.2V
iC = (10 – 0.2) / 1000 = 9.8mA
iC = βiB
Vin = iB*RB + VBE
Set VBE = Vcut-in = 0.7V
Vin = 0.098*(10-3)*10000 + 0.7V
Vin = 1.68V or greater.
![Page 20: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/20.jpg)
From
3rd Exercise
Turns on/off coils digitally
BJT as Switch
![Page 21: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/21.jpg)
44
55
22
33
11 Introduction to Transistor(Speaker: Sung-bum Kang)
Field Effect Transistor(Speaker: Hongchul Sohn)
Power Transistor(Speaker: Wenwei Xu)
Applications of Transistor(Speaker: Wenwei Xu)
Bipolar Junction Transistor(Speaker: Keun Jae Kim)
“Transistor” Part 3
![Page 22: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/22.jpg)
Field-Effect Transistors
Basics Conduction of a “channel” is controlled by electric field effect
Three terminals: gate, source, drain
Voltage-controlled current device
control terminal
current channel
of charge carriers for charge carriers
control voltage
Very little current flows through input (gate) terminals
![Page 23: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/23.jpg)
Field-Effect Transistors
BJT vs. FET What was BJT then?
A current-controlled current device
Comparison
![Page 24: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/24.jpg)
Field-Effect Transistors
Types JFET (Junction FET)
MOSFET (Metal-oxide-semiconductor FET)
MESFET (Metal-semiconductor FET)
HFET (Hetero-structure FET)
MODFET (Modulation doped FET)
IGBT (Insulated-gate bipolar transistor)
Power MOSFETs
FREDFET (Fast reverse or fast recovery epitaxial diode FET)
ISFET (Ion-sensitive FET)
DNAFET
JFET (Junction FET)
MOSFET (Metal-oxide-semiconductor FET)
![Page 25: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/25.jpg)
JFETs
JFETs n-channel
General Properties Advantages: Much higher input resistance, lower noise, easier
fabrication, ability to handle higher currents and powers
Disadvantages: Slower speeds in switching circuits, smaller bandwidth for a given gain in an amplifier
p-channel
![Page 26: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/26.jpg)
n-channel JFET
Characteristics
![Page 27: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/27.jpg)
n-channel JFET
Characteristics Idealized Static
2(1 )GSD DSS
P
vi I
V
![Page 28: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/28.jpg)
n-channel JFET
Characteristics Practical Static
2(1 ) (1 )GS DSD DSS
P A
v vi I
V V
Transfer
![Page 29: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/29.jpg)
MOSFETs
MOSFETs or Insulated-gate FET (IGFET)
n-channel Enhancement
General Properties Input resistance even higher
Used primarily in digital electronic circuits
Provide controlled-source characteristics in amplifier circuits
n-channel Depletion
![Page 30: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/30.jpg)
n-channel Enhancement MOSFET
Characteristics
![Page 31: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/31.jpg)
n-channel Enhancement MOSFET
Characteristics Practical
2( ) (1 )DSD GS T
A
vi K v V
V 2[2( ) ]D GS T DS DSi K v V v v
![Page 32: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/32.jpg)
n-channel Depletion MOSFET
Characteristics Practical
2[2(1 )( ) ( ) ]GS DS DSD DSS
P P P
v v vi I
V V V 2(1 ) (1 )GS DS
D DSSP A
v vi I
V V
![Page 33: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/33.jpg)
Task: Design a n-channel common-source JFET Amplifier
Amplifiers, Switches
Applications
You CAN do it!! Psst! You can read it!!http://www.electronics-tutorials.ws/amplifier/amp_3.html
![Page 34: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/34.jpg)
“Transistor” Part 4
Introduction to Transistor(Speaker: Sung-bum Kang)
Field Effect Transistor(Speaker: Hongchul Sohn)
Power Transistor(Speaker: Wenwei Xu)
11
33
Applications of Transistor(Speaker: Wenwei Xu)
Bipolar Junction Transistor(Speaker: Keun Jae Kim)22
44
55
![Page 35: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/35.jpg)
Power Transistor
Concerned with delivering high power Used in high voltage and high current application
In generalFabrication process different in order to: Dissipate more heat Avoid breakdownLower gain than signal level transistor
![Page 36: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/36.jpg)
Power BJT
Same structure to the signal level BJT The active area is distinctively higher-high current
capacity Thick and low-doped collector region Large heat dissipation--- larger dimensions
![Page 37: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/37.jpg)
Power MOSFET
Same working principles to MOSFET
Designed to handle large power
Low internal voltage drop and high current capacity
High commutation speed and good efficiency at low voltages—high speed switch
![Page 38: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/38.jpg)
Applications of Transistorbuilding blocks for modern electronics
Digital logic circuits Microprocessors, microcontrollers, chips (TTL) Photo-transistors Replaces normal switches, mechanical relays. A/D converter Encoders Multiplexers Power supplies
more…
microprocessorwireless
communicationmotor
headphone, microphone
![Page 39: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/39.jpg)
Applications(cont.)
– Switch for a digital signal: BJT or MOSFET – Switch for a analog signal: JFET – Switch for a power signal: Power MOSFET or BJT – Current controlled-current amplifier: BJT – Voltage controlled-current amplifier: JFET or MOSFET
![Page 40: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/40.jpg)
Small input voltage and large output currentoperated in the cut-off region(open) and saturation region(close)
Example: 2N3904 NPNAssuming LED requires 20-40 mA to provide a bright display and has 2 voltage drop when forwarded biased
Output=0V—offOutput=5V---on, the transistor is in saturation, with base current
(5 0.7 ) /10 0.43BI V V K mA
Collector current (LED current) is limited by collector resistor
mAVVVIC 28100/)2.025(
BJT as switches
![Page 41: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/41.jpg)
BJT as amplifiers
Audio amplifiers, radio frequency amplifiers, regulated power supplies
Low input impedance and high voltage gain
ExampleSpeaker amplifier
BJT series produce higher gain
![Page 42: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/42.jpg)
Applications of FET
Advantages of FET over BJT They are devices controlled by voltage with a very high input
impedance (107 to 1012 ohms) FETs generate a lower noise level than the Bipolar Junction
Transistor (BJT) FETs are more stable than BJT with temperature FETs are easier to manufacture than the BJT, because they require
fewer steps to be built and they allow more integrated devices in the same IC
FETs behave like resistors controlled by voltage for small drain-source voltage values
The high input impedance of FET allows them to withhold loads long enough to allow its usage as storage elements
Power FETs can dissipate higher power and can switch very large currents.
![Page 43: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/43.jpg)
Applications of FET
Amplifiers•Small Signal•Low Distortion•High Gain•Low Noise amplifier•Selectivity•High-Frequency
Switches•Chopper-Type•Analog Gate•Communicator
Protection Diodes•Low-leakage
Current LimitersResistorsMixersOscillators
![Page 44: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/44.jpg)
FET as analog switch-example
When VGS = 0, FET becomes saturated and it behaves like a small resistance(<100 ohm) and, therefore,
VOUT = {RDS/ (RD + RDS (ON))}* Vin
RD>>RDS, VOUT → 0
When a negative voltage equal to VGS (OFF) is applied to the gate, the FET operates in the cut-off region and it acts like a very high resistance usually of some mega ohms. Hence output voltage becomes nearly equal to input voltage.
![Page 45: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/45.jpg)
Contact information(in order of presenting)
Sung-bum Kang [email protected] Keun Jae Kim [email protected] Hongchul Sohn [email protected] Wenwei Xu [email protected]
![Page 46: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/46.jpg)
References www.wikipedia.org www.google.com
“Introduction to Electrical Engineering”, Mulukata S. Sarma, Oxford University Press, 2001, Chap. 7.4~8.4. Fall 2008 Transistors Slides http://www-g.eng.cam.ac.uk/mmg/teaching/linearcircuits/index.html http://en.wikipedia.org/wiki/FET http://en.wikipedia.org/wiki/JFET http://en.wikipedia.org/wiki/MOSFET http://www.slideshare.net/guest3b5d8a/fets “Introduction to Electrical Engineering”, Mulukata S. Sarma, Oxford University Press, 2001, Chap. 7.4~8.4. Fall 2008 Transistors Slides http://www-g.eng.cam.ac.uk/mmg/teaching/linearcircuits/index.html http://en.wikipedia.org/wiki/FET http://en.wikipedia.org/wiki/JFET http://en.wikipedia.org/wiki/MOSFET http://www.slideshare.net/guest3b5d8a/fets
http://www.electronics.dit.ie/staff/ypanarin/Lecture%20Notes/K235-1/2%20Transistor-Thyristor.pdf http://ecee.colorado.edu/~bart/book/book/chapter5/ch5_9.htm http://www.ece.mtu.edu/labs/EElabs/EE3305/Bipolar_Junction_Transistors.pdf http://www.partminer.com/glossaryhtml/bjt.htm http://www.lycos.com/info/bipolar-junction-transistor--applications.html http://jimwarholic.com/uploaded_images/power-supply-768753.jpg http://abbydamico.files.wordpress.com/2008/09/microprocessor-athlon-64.jpg http://www.billfrymire.com/blog/wp-content/uploads/2008/05/wireless-communication-connection-1000.jpg http://www.cybermediatech.com/images/WirelessHeadphone-big.jpg http://www.colorado.edu/physics/phys3330/phys3330_fa09/pdfdocs/AN101FETintro.pdf http://www.circuitstoday.com/fet-applications
![Page 47: ME 6405 Student Lecture Transistor](https://reader035.vdocument.in/reader035/viewer/2022062422/56814073550346895dabf328/html5/thumbnails/47.jpg)
Thank you!