mediant msbr - audiocodes...when upgrade is performed from version 6.8 to version 7.2 and the...

Configuration Note

Multi-Service Business Routers Product Series

Mediant MSBR

Upgrading Firmware from Version 6.8 to Version 7.2

Version 7.2 3 Mediant MSBR

Configuration Note Contents

Table of Contents 1 Introduction ......................................................................................................... 7

2 Hardware and Software Requirements .............................................................. 9

2.1 Hardware Requirements ......................................................................................... 9 2.2 Software Requirements .......................................................................................... 9

3 Upgrade Procedure ........................................................................................... 11

3.1 Single Network Mode ........................................................................................... 12

4 Data CLI Changes.............................................................................................. 13

4.1 DSL Operation Mode ............................................................................................ 13 4.2 Command Path Changes ..................................................................................... 13

5 Data CLI Changes Examples ............................................................................ 15

5.1 Version 6.8 Configuration ..................................................................................... 15 5.2 Version 7.2.150 Configuration .............................................................................. 21

6 CLI Voice Changes ............................................................................................ 31

6.1 Simple Voice Configuration Changes Example ..................................................... 31

Configuration Note 4 Document #: LTRT-23304

Upgrading to Version 7.2

This page is intentionally left blank.


Configuration Note Notices

Notice Information contained in this document is believed to be accurate and reliable at the time of printing. However, due to ongoing product improvements and revisions, AudioCodes cannot guarantee accuracy of printed material after the Date Published nor can it accept responsibility for errors or omissions. Updates to this document and other documents as well as software files can be downloaded by registered customers at http://www.audiocodes.com/downloads.

This document is subject to change without notice.

Date Published:May-28-2017

WEEE EU Directive Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product.

Customer Support Customer technical support and services are provided by AudioCodes or by an authorized AudioCodes Service Partner. For more information on how to buy technical support for AudioCodes products and for contact information, please visit our Web site at www.audiocodes.com/support.

Abbreviations and Terminology Each abbreviation, unless widely used, is spelled out in full when first used.

Related Documentation

Document Name

Media Gateway & SBC CLI Reference Guide Ver. 7.2

MSBR Simplifying Network CLI Configuration Note Ver. 7.2

http://www.audiocodes.com/downloads

http://www.audiocodes.com/support



Document Revision Record

LTRT Description

23303 Initial document release for Version 7.2

23304 Added CLI Voice Changes section.

Documentation Feedback AudioCodes continually strives to produce high quality documentation. If you have any comments (suggestions or errors) regarding this document, please fill out the Documentation Feedback form on our Web site at http://www.audiocodes.com/downloads.

http://www.audiocodes.com/downloads


Configuration Note 1. Introduction

1 Introduction This document describes the following important information for MSBR users when upgrading to Version 7.2: CLI Changes: Most of the changes to the CLI affect the Voice configuration. Only a

few of the CLI changes affect the Data configuration. These changes are described in this document.

Old CLI Script: "show running-config" output that has been copied from Version 6.8 can be inserted into 7.2. Also commands copied from Version 6.8 will work if inserted using the full command text string. For Example: "show" will work, and "sh …" will not work.

Autocomplete: Entering CLI commands using autocomplete i.e. using the tab key, will not work for existing Version 6.8 commands whose path has been changed in Version 7.2 (as shown in Section 4.2).

Dual Network Mode: When upgrade is performed from Version 6.8 to Version 7.2 and the existing Version 6.8 platform is configured to work in Dual Network mode, the Dual Network mode configuration remains. New MSBR devices with a clean installation of Version 7.2 are by default configured with a Single Network mode.

In addition to the above, this document also includes instructions on how to upgrade device firmware to Version 7.2 and also includes example configuration output for both Version 6.8 and Version 7.2.


Configuration Note 2. Hardware and Software Requirements

2 Hardware and Software Requirements This chapter describes the hardware and software requirements for running MSBR Version 7.2 firmware.

2.1 Hardware Requirements The following hardware platforms are supported for MSBR Version 7.2: Mediant 500L MSBR Mediant 500 MSBR Mediant 800 MSBR

2.2 Software Requirements The software can be loaded to the MSBR using FTP, TFTP, HTTP or HTTPS. For

best results, it is recommended to use HTTP or HTTPS servers. Upgrade to Version 7.2 needs to be performed from at least Version 6.80.286.002. If

the MSBR version is lower than Version 6.80.286.002, the MSBR first needs to be upgraded to this version.


Configuration Note 3. Upgrade Procedure

3 Upgrade Procedure The upgrade can be performed using the CLI, Web GUI or by using Management Software using CWMP protocol.

To upgrade using the CLI, do one of the following:

Copy firmware from an HTTP server using IP: copy firmware from http://10.199.0.100/MSBR_SIP_F7.20A.140.512.cmp

Copy firmware using an HTTPS server using a DNS name copy firmware from https://someserver/MSBR_SIP_F7.20A.140.512.cmp

To upgrade using the Web:

1. From the Device Actions drop-down list, select Software Upgrade Wizard:

Figure 3-1: Software Upgrade Wizard

2. Choose a file to load and click the Load File button.

Figure 3-2: Load File

3. When the file has finished loading, click the Reset button.

http://10.199.0.100/MSBR_SIP_F7.20A.140.512.cmp

https://someserver/MSBR_SIP_F7.20A.140.512.cmp



Following the upgrade, specific commands will be located in different paths. If management software is used, for example a CWMP server, make sure that you have copied a Version 7.2.150 or later configuration file to the Management server. It is recommended to download the new configuration to the Management Software after the MSBR have been upgraded. It is possible to manually download the configuration from the device using the copy command. For example: copy cli-script to tftp://10.51.13.5/config.cli

This command copies the configuration in the form of a CLI script (this is displayed when the Show Run command is used) to the TFTP server address e.g. 10.51.13.5 to the file config.cli. You can also use a FTP, HTTP, or HTTPS server for this command.

3.1 Single Network Mode After you have upgraded, it is recommended to configure your device for the Single Network mode. In this mode of operation, the Voice application runs on the MSBR as a linked application, and therefore the network configuration is not required to be configured on the Voice part. For more information about switching to Single Network mode, refer to document MSBR Simplifying Network CLI Configuration Note Ver. 7.2.


Configuration Note 4. Data CLI Changes

4 Data CLI Changes This chapter summarizes the changes to the CLI interface for Version 7.2.

4.1 DSL Operation Mode All subcommands from the DSL interface were removed because the DSL operation mode was changed. From this version onwards, users cannot configure the specific DSL operation mode ADSL or VDSL. These operation modes will be automatically selected by the device through sensing the signals on the DSL line.

4.2 Command Path Changes In Version 7.2, the location for specific commands has been changed in the command tree. Example: Binding an application configuration to an interface. Version 6.8:

# configure system (config-system)# bind interface gigabitethernet 0/0 voip

Version 7.2: # configure network (config-network)# bind interface gigabitethernet 0/0 voip

The following table describes the changes in Configuration commands:

Table 4-1: Configuration Command Path Changes

Command Description Command Path

Version 6.8 Version 7.2

bind Binds application to interface.

config-system config-network

interface Configures OSN interface.


hostname Sets product hostname.


nqm Configures Network Quality Monitoring.


tftp-server Internal TFTP server


logging Logging configuration

config-system config-troubleshoot

access-list Network access list.

config-voip config-network

dhcp-server DHCP server configuration.

config-voip (was previously dhcp)

config-network

dns DNS configuration.

config-voip config-network



The following table describes these changes in Show commands:

Table 4-2: Show Commands Changes

Command Description Version 6.8 Path Version 7.2 Path

show version Displays software version.

Show system version Show version

show system date or show system time

Displays current system date or time.

Show system date Or Show system time

show system clock

show system nqm Displays networking information of VoIP applications.

Show system nqm Show nqm


Configuration Note 5. Data CLI Changes Examples

5 Data CLI Changes Examples This chapter shows comparison example running configurations for Version 6.8 and Version 7.2.150.

5.1 Version 6.8 Configuration # Running Configuration ## VoIP Configuration configure voip tls 0 name default tls-version unlimited ciphers-server "RC4:AES128" ciphers-client "RC4:DEFAULT" ocsp-server disable ocsp-port 2560 ocsp-default-response reject exit coders-and-profiles coders-group-0 0 name "g711Alaw64k" p-time 20 activate exit interface network-dev 0 name "vlan 1" activate exit interface network-if 0 ip-address 192.168.0.2 prefix-length 24 gateway 192.168.0.1 name "Voice" primary-dns 192.168.0.1 underlying-dev "vlan 1" activate exit voip-network realm 0 name "MRWAN" ipv4if "WAN" port-range-start 6000 session-leg 256 port-range-end 8550 is-default true activate exit voip-network srd 0 name "SRDWAN" media-realm-name "MRWAN" activate exit voip-network sip-interface 0 interface-name "SIPWAN" network-interface "WAN" activate exit voip-network proxy-set 0 proxy-name ""



activate exit gw hunt-or-trunk-group trunk-group 0 trunk-group-id 1 first-b-channel 1 last-b-channel 1 first-phone-number "1001" module 2 activate exit gw routing ip2tel-routing 0 dst-phone-prefix "*" trunk-group-id 1 src-phone-prefix "*" activate exit gw hunt-or-trunk-group trunk-group-setting 0 trunk-group-id 1 channel-select-mode dst-phone-number activate exit gw digitalgw rp-network-domains 1 name "dsn" activate exit gw digitalgw rp-network-domains 2 name "dod" activate exit gw digitalgw rp-network-domains 3 name "drsn" activate exit gw digitalgw rp-network-domains 5 name "uc" activate exit gw digitalgw rp-network-domains 7 name "cuc" activate exit gw digitalgw digital-gw-parameters answer-detector-cmd 10486144 energy-detector-cmd 587202560 activate exit gw analoggw authentication 0 user-name "1001" password C35/aHw+T31zfQ== obscured activate exit ldap ldap-search-server-method sequentialy activate exit media udp-port-configuration udp-port-spacing 10 activate exit services least-cost-routing routing-rule-groups 0 lcr-default-cost highest-cost activate



exit sip-definition proxy-and-registration authentication-mode per-endpoint enable-proxy use-proxy enable-registration on activate exit sip-definition advanced-settings set ldap-primary-key "telephoneNumber" activate exit tdm pcm-law-select mulaw activate exit voip-network proxy-ip 0 proxy-address "10.4.2.102" activate exit exit ## System Configuration configure system ntp set primary-server "0.0.0.0" activate exit radius set shared-secret "$1$woS2sLC0opqIjoKZng==" activate exit snmp no activate-keep-alive-trap activate exit web wan-http-allow on activate exit hostname "Mediant 500L - MSBR" configuration-version 0 exit configure data radio shutdown interface GigabitEthernet 0/0 ip address dhcp no ip dhcp-client default-route mtu auto desc "WAN Copper" no ipv6 enable speed auto duplex auto no service dhcp ip dns server static napt firewall enable no shutdown exit interface Fiber 0/1 no ip address mtu auto



desc "WAN Fiber" no ipv6 enable no service dhcp ip dns server static no shutdown exit interface dsl 0/2 #DSL configuration is automatic #Termination cpe mode ADSL auto-switch-attempts vdsl 2 vdsl-v43 0 adsl 2 no shutdown exit interface EFM 0/2 #This interface is DISABLED due to physical layer configuration no ip address mtu 1568 desc "WAN DSL" no ipv6 enable no service dhcp ip dns server static no shutdown exit interface FastEthernet 1/1 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface FastEthernet 1/2 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface FastEthernet 1/3 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface FastEthernet 1/4 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface ATM 0/0 encapsulation ethoa-snap pvc 0/35 ubr ip address auto no ip dhcp-client default-route no ipv6 enable ip dns server auto napt firewall enable mtu auto



exit interface VLAN 1 no ip address bridge-group 1 mtu auto desc "LAN switch VLAN 1" no ipv6 enable no service dhcp no link-state monitor no shutdown exit interface BVI 1 ip address 192.168.0.1 255.255.255.0 mtu auto desc "LAN Bridge" no ipv6 enable ip dhcp-server network 192.168.0.3 192.168.0.8 255.255.255.0 ip dhcp-server dns-server 0.0.0.0 ip dhcp-server netbios-name-server 0.0.0.0 ip dhcp-server lease 0 1 0 ip dhcp-server provide-host-name ip dhcp-server ntp-server 0.0.0.0 ip dhcp-server tftp-server 0.0.0.0 ip dhcp-server override-router-address 0.0.0.0 ip dhcp-server next-server 0.0.0.0 service dhcp ip dns server static no napt no firewall enable no shutdown exit interface dot11radio 1 #This interface is DISABLED due to physical layer configuration no ip address bridge-group 1 mtu auto desc "LAN Wireless 802.11n Access Point" no ipv6 enable no service dhcp ssid MSBR broadcast security mode NONE no security mac mode mode ngb channel width 40/20 channel auto power 100 beacon dtim-period 1 beacon period 100 fragment threshold 2346 cts mode none cts type cts burst num 3 burst time 2 rts threshold 2346 wmm shutdown exit interface pppoe 0 firewall enable napt mtu auto



ppp user tim obscured-pass Vhc2aWtpb2lr ppp authentication chap no ppp authentication ms-chap no ppp authentication ms-chap-v2 no ppp authentication pap ppp lcp-echo 6 5 no ppp compression ip address auto no ipv6 address ip dns server auto underlying GigabitEthernet 0/0 network wan no shutdown exit qos match-map input "test" BVI 1 match any set precedence routine exit ip nat translation udp-timeout 120 ip nat translation tcp-timeout 3600 ip nat translation icmp-timeout 6 ip firewall allow-icmp # Note: The following WAN ports are in use by system services, # conflicting rules should not be created: # Ports 80 - 80 --> HTTP # Ports 82 - 82 --> TR069 # Ports 6000 - 8550 --> RealmPortPool::MRWAN # Ports 5060 - 5060 --> SIPUDP#0 # Ports 5060 - 5060 --> SIPLISTENING#0 # Ports 5061 - 5061 --> SIPLISTENING#0 # Note: The following NAT rules are in effect for system services, # conflicting rules should not be created: # RealmPortPool::MRWAN: LAN ports 6000-8550 to WAN IP 10.31.2.101 ports 6000-8550, interface GigabitEthernet 0/0 # SIPUDP#0: LAN ports 5060-5060 to WAN IP 10.31.2.101 ports 5060-5060, interface GigabitEthernet 0/0 # SIPLISTENING#0: LAN ports 5060-5060 to WAN IP 10.31.2.101 ports 5060-5060, interface GigabitEthernet 0/0 # SIPLISTENING#0: LAN ports 5061-5061 to WAN IP 10.31.2.101 ports 5061-5061, interface GigabitEthernet 0/0 ip route 0.0.0.0 0.0.0.0 PPPOE 0 1 ip route 10.4.2.102 255.255.255.255 10.31.0.1 GigabitEthernet 0/0 1 ip domain name home ip domain localhost msbr pm sample-interval minute 5 pm sample-interval seconds 15 exit



5.2 Version 7.2.150 Configuration # Running Configuration M500L ## IP NETWORK configure network tls 0 name default tls-version unlimited ciphers-server "RC4:AES128" ciphers-client "RC4:DEFAULT" ocsp-server disable ocsp-port 2560 dh-key-size 1024 ocsp-default-response reject exit network-dev 0 name "vlan 1" activate exit interface network-if 0 ip-address 192.168.0.2 prefix-length 24 gateway 192.168.0.1 name "Voice" primary-dns 192.168.0.1 underlying-dev "vlan 1" activate exit network-settings single-net-mode disable activate exit # The following line is not activated poe-table 0 port-enable enable no activate exit # The following line is not activated poe-table 1 port-enable enable no activate exit # The following line is not activated poe-table 2 port-enable enable no activate exit # The following line is not activated poe-table 3 port-enable enable no activate exit # The following line is not activated poe-table 4 port-enable enable no activate exit # The following line is not activated poe-table 5



port-enable enable no activate exit # The following line is not activated poe-table 6 port-enable enable no activate exit # The following line is not activated poe-table 7 port-enable enable no activate exit # The following line is not activated poe-table 8 port-enable enable no activate exit # The following line is not activated poe-table 9 port-enable enable no activate exit # The following line is not activated poe-table 10 port-enable enable no activate exit # The following line is not activated poe-table 11 port-enable enable no activate exit exit ## SIGNALING & MEDIA configure voip coders-and-profiles audio-coders-groups 0 coders-group-name "AudioCodersGroups_0" activate exit coders-and-profiles audio-coders 0/0 name g711-alaw p-time 20 rate 64 activate exit gateway trunk-group 0 trunk-group-id 1 first-b-channel 1 last-b-channel 1 first-phone-number "1001" module 2 activate exit realm 0 name "MRWAN" ipv4if "WAN" port-range-start 6000 session-leg 256 is-default enable



activate exit sbc routing sbc-routing-policy 0 name "Default_SBCRoutingPolicy" lcr-default-cost highest-cost activate exit srd 0 name "SRDWAN" activate exit sip-interface 0 interface-name "SIPWAN" network-interface "WAN" media-realm-name "MRWAN" activate exit proxy-set 0 proxy-name "ProxySet_0" gwipv4-sip-int-name "SIPWAN" activate exit ip-group 0 name "Default_IPG" proxy-set-name "ProxySet_0" classify-by-proxy-set disable activate exit gateway trunk-group-setting 0 trunk-group-id 1 channel-select-mode dst-phone-number activate exit gateway routing gw-routing-policy 0 lcr-default-cost highest-cost activate exit gateway routing ip2tel-routing 0 dst-phone-prefix "*" trunk-group-id 1 src-phone-prefix "*" activate exit gateway digital settings answer-detector-cmd 10486144 energy-detector-cmd 587202560 activate exit gateway digital rp-network-domains 1 name "dsn" activate exit gateway digital rp-network-domains 2 name "dod" activate exit gateway digital rp-network-domains 3 name "drsn" activate exit gateway digital rp-network-domains 5 name "uc"



activate exit gateway digital rp-network-domains 7 name "cuc" activate exit gateway analog authentication 0 user-name "1001" password C35/aHw+T31zfQ== obscured activate exit gateway analog authentication 1 user-name "" activate exit gateway analog authentication 2 user-name "" activate exit gateway analog authentication 3 user-name "" activate exit gateway analog authentication 4 user-name "" activate exit gateway analog authentication 5 user-name "" activate exit gateway analog authentication 6 user-name "" activate exit gateway analog authentication 7 user-name "" activate exit media tdm pcm-law-select mulaw activate exit media rtp-rtcp udp-port-spacing 10 activate exit proxy-ip 0/0 proxy-address "10.4.2.102" activate exit sip-definition settings ldap-primary-key "telephoneNumber" activate exit sip-definition proxy-and-registration authentication-mode per-endpoint enable-proxy use-proxy enable-registration on activate exit exit



## ADMINISTRATION configure system ntp primary-server "0.0.0.0" activate exit snmp settings no activate-keep-alive-trap activate exit web wan-http-allow on activate exit hostname M500L configuration-version 0 create-users-table user Admin password 29237978cb53f3b4dfebd1c2c61b454dade6682ee89fe8209935c7b640141aea8b4a3a83682cbc4ce82f89f6d2044ecd obscured public key % status valid privilege sec-admin password-age 0 block-duration 60 session-timeout 15 session-limit 5 cli-session-limit -1 exit user User password e1ea1bdcb596c22c1c8b92aa5a114bf614fed569b5e6454857f5ad8194f36f530ed0adfd864ed68490cc329baa1281be obscured public key % status valid privilege user password-age 0 block-duration 60 session-timeout 15 session-limit 5 cli-session-limit -1 exit exit ## TROUBLESHOOT configure troubleshoot activity-log config-changes off files-loading off device-reset off flash-burning off software-update off unauthorized-access off sensitive-config-changes off login-and-logout off cli-commands-log off action-execute off activate exit



activate exit # DATA ROUTER configure data radio shutdown interface GigabitEthernet 0/0 ip address dhcp no ip dhcp-client default-route mtu auto desc "WAN Copper" no ipv6 enable speed auto duplex auto no service dhcp ip dns server static napt firewall enable no shutdown exit interface Fiber 0/1 no ip address mtu auto desc "WAN Fiber" no ipv6 enable no service dhcp ip dns server static no shutdown exit interface dsl 0/2 #DSL configuration is automatic #Termination cpe no shutdown exit interface EFM 0/2 #This interface is DISABLED due to physical layer configuration no ip address mtu auto desc "WAN DSL" no ipv6 enable no service dhcp ip dns server static no shutdown exit interface FastEthernet 1/1 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface FastEthernet 1/2 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface FastEthernet 1/3 speed auto duplex auto



switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface FastEthernet 1/4 speed auto duplex auto switchport mode trunk switchport trunk native vlan 1 no shutdown exit interface ATM 0/0 encapsulation ethoa-snap pvc 0/35 ubr ip address auto no ip dhcp-client default-route no ipv6 enable ip dns server auto napt firewall enable mtu auto exit interface VLAN 1 no ip address bridge-group 1 mtu auto desc "LAN switch VLAN 1" no ipv6 enable no service dhcp no link-state monitor no shutdown exit interface BVI 1 ip address 192.168.0.1 255.255.255.0 mtu auto desc "LAN Bridge" no ipv6 enable ip dhcp-server network 192.168.0.3 192.168.0.8 255.255.255.0 ip dhcp-server dns-server 0.0.0.0 ip dhcp-server netbios-name-server 0.0.0.0 ip dhcp-server lease 0 1 0 ip dhcp-server provide-host-name ip dhcp-server ntp-server 0.0.0.0 ip dhcp-server tftp-server 0.0.0.0 ip dhcp-server override-router-address 0.0.0.0 ip dhcp-server next-server 0.0.0.0 service dhcp ip dns server static no napt no firewall enable no shutdown exit interface dot11radio 1 #This interface is DISABLED due to physical layer configuration no ip address bridge-group 1 mtu auto desc "LAN Wireless 802.11n Access Point" no ipv6 enable no service dhcp ssid MSBR



broadcast security mode NONE no security mac mode mode ngb channel width 40/20 channel auto power 100 beacon dtim-period 1 beacon period 100 fragment threshold 2346 cts mode none cts type cts burst num 3 burst time 2 rts threshold 2346 wmm shutdown exit interface pppoe 0 firewall enable napt mtu auto ppp user tim obscured-pass Vhc2aWtpb2lr ppp authentication chap no ppp authentication ms-chap no ppp authentication ms-chap-v2 no ppp authentication pap ppp lcp-echo 6 5 no ppp compression ip address auto no ipv6 address ip dns server auto underlying GigabitEthernet 0/0 network wan no shutdown exit qos match-map input "test" BVI 1 match any set precedence routine exit ip nat translation udp-timeout 120 ip nat translation tcp-timeout 3600 ip nat translation icmp-timeout 6 ip firewall allow-icmp # Note: The following WAN ports are in use by system services, # conflicting rules should not be created: # Ports 80 - 80 --> HTTP # Ports 82 - 82 --> TR069 # Ports 6000 - 8559 --> RealmPortPool::MRWAN # Ports 5060 - 5060 --> SIPUDP#0 # Ports 5060 - 5060 --> SIPLISTENING#0 # Ports 5061 - 5061 --> SIPLISTENING#0 # Note: The following NAT rules are in effect for system services, # conflicting rules should not be created: # RealmPortPool::MRWAN: LAN ports 6000-8559 to WAN IP 10.31.2.101 ports 6000-8559, interface GigabitEthernet 0/0 # SIPUDP#0: LAN ports 5060-5060 to WAN IP 10.31.2.101 ports 5060-5060, interface GigabitEthernet 0/0 # SIPLISTENING#0: LAN ports 5060-5060 to WAN IP 10.31.2.101 ports 5060-5060, interface GigabitEthernet 0/0 # SIPLISTENING#0: LAN ports 5061-5061 to WAN IP 10.31.2.101 ports 5061-5061, interface GigabitEthernet 0/0 ip route 0.0.0.0 0.0.0.0 PPPOE 0 1



ip route 10.4.2.102 255.255.255.255 10.31.0.1 GigabitEthernet 0/0 1 ip domain name home ip domain localhost msbr pm sample-interval minute 5 pm sample-interval seconds 15 exit


Configuration Note 6. CLI Voice Changes

6 CLI Voice Changes Most of CLI changes are in the Voice section. To keep the new version backward compatible, the old CLI commands can be pasted to the MSBR. However the TAB key will not complete partially written commands and the '?' wont display the old CLI commands. The following section compares by sections, the changes in the CLI Voice commands. It is also recommended to review the CLI Configuration Guide to learn the new Voice commands.

6.1 Simple Voice Configuration Changes Example In this configuration, the following topology is configured:

Figure 6-1: Configured Topology



In the following table, the left column lists Version 6.8 commands, and the right column lists the equivalent command in Version 7.2. Both configurations achieve the same goal. The table is arranged in the order of the Version 7.2 CLI script, while the Version 6.8 commands is in order as it appears in the output of the "show run" command.

Version 6.8 Version 7.2

configure voip configure network

tls 0 name default tls-version unlimited ciphers-server "RC4:AES128" ciphers-client "RC4:DEFAULT" ocsp-server disable ocsp-port 2560 ocsp-default-response reject exit

tls 0 name default tls-version unlimited ciphers-server "RC4:AES128" ciphers-client "RC4:DEFAULT" ocsp-server disable ocsp-port 2560 dh-key-size 1024 ocsp-default-response reject exit

interface network-dev 0 name "vlan 1" activate exit

network-dev 0 name "vlan 1" activate exit

interface network-if 0 ip-address 192.168.0.2 gateway 192.168.0.1 name "Voice" primary-dns 192.168.0.1 underlying-dev "vlan 1" activate exit

interface network-if 0 ip-address 192.168.0.2 gateway 192.168.0.1 name "Voice" primary-dns 192.168.0.1 underlying-dev "vlan 1" activate exit

configure voip configure voip

coders-and-profiles coders-group-0 0 name "g711Alaw64k" p-time 20 activate exit

coders-and-profiles audio-coders-groups 0 coders-group-name "AudioCodersGroups_0" activate exit coders-and-profiles audio-coders 0/0 name g711-alaw p-time 20 rate 64 activate exit

gateway trunk-group 0 trunk-group-id 1 first-b-channel 1 last-b-channel 1 first-phone-number "2002" module 2 activate exit



voip-network realm 0 name "MRWAN" ipv4if "WAN" port-range-start 6000 session-leg 256 port-range-end 8550 is-default true activate exit

realm 0 name "MRWAN" ipv4if "WAN" port-range-start 6000 session-leg 256 is-default enable activate exit

sbc routing sbc-routing-policy 0 name "Default_SBCRoutingPolicy" lcr-default-cost highest-cost activate exit

voip-network srd 0 name "SRDWAN" media-realm-name "MRWAN" activate exit

srd 0 name "SRDWAN" activate exit

message message-policy 0 name "Malicious Signature DB Protection" max-message-length -1 max-header-length -1 max-body-length -1 max-num-headers -1 max-num-bodies -1 send-rejection policy-drop method-list-type policy-blacklist body-list-type policy-blacklist signature-db-enable enabled activate exit

voip-network sip-interface 0 interface-name "SIPWAN" network-interface "WAN" activate exit

sip-interface 0 interface-name "SIPWAN" network-interface "WAN" media-realm-name "MRWAN" activate exit

voip-network proxy-set 0 proxy-name "" activate exit

proxy-set 0 proxy-name "ProxySet_0" gwipv4-sip-int-name "SIPWAN" activate exit

voip-network proxy-set 0 proxy-name "" activate exit

ip-group 0 name "Default_IPG" proxy-set-name "ProxySet_0" srd-name "SRDWAN" classify-by-proxy-set disable activate exit



gw hunt-or-trunk-group trunk-group 0 trunk-group-id 1 first-b-channel 1 last-b-channel 1 first-phone-number "2002" module 2 activate exit

gateway trunk-group-setting 0 trunk-group-id 1 channel-select-mode dst-phone-number activate exit

gw hunt-or-trunk-group trunk-group-setting 0 trunk-group-id 1 channel-select-mode dst-phone-number activate

gateway routing gw-routing-policy 0 lcr-default-cost highest-cost activate exit

gw routing ip2tel-routing 0 dst-phone-prefix "*" trunk-group-id 1 src-phone-prefix "*" activate exit

gateway routing ip2tel-routing 0 dst-phone-prefix "*" trunk-group-id 1 src-phone-prefix "*" activate exit

gw digitalgw rp-network-domains 1 name "dsn" activate exit gw digitalgw rp-network-domains 2 name "dod" activate exit gw digitalgw rp-network-domains 3 name "drsn" activate exit gw digitalgw rp-network-domains 5 name "uc" activate exit gw digitalgw rp-network-domains 7 name "cuc" activate exit gw digitalgw digital-gw-parameters answer-detector-cmd 10486144 energy-detector-cmd 587202560 activate exit

gateway digital settings answer-detector-cmd 10486144 energy-detector-cmd 587202560 activate exit gateway digital rp-network-domains 1 name "dsn" activate exit gateway digital rp-network-domains 2 name "dod" activate exit gateway digital rp-network-domains 3 name "drsn" activate exit gateway digital rp-network-domains 5 name "uc" activate exit gateway digital rp-network-domains 7 name "cuc" activate exit

gw analoggw authentication 0 user-name "2002" password F2JrfGgpQ2p/cQ== obscured activate exit

gateway analog authentication 0 user-name "2002" password F2JrfGgpQ2p/cQ== obscured activate exit gateway analog authentication 1



user-name "" activate exit gateway analog authentication 2 user-name "" activate exit gateway analog authentication 3 user-name "" activate exit gateway analog authentication 4 user-name "" activate exit gateway analog authentication 5 user-name "" activate exit gateway analog authentication 6 user-name "" activate exit gateway analog authentication 7 user-name "" activate exit

tdm pcm-law-select mulaw activate exit

media tdm pcm-law-select mulaw activate exit

media udp-port-configuration udp-port-spacing 10 activate exit

media rtp-rtcp udp-port-spacing 10 activate exit

voip-network proxy-ip 0 proxy-address "10.4.2.102" activate exit

proxy-ip 0/0 proxy-address "10.4.2.102" activate exit

sbc malicious-signature-database 0 name "SIPVicious" pattern "Header.User-Agent.content prefix 'friendly-scanner'" activate exit sbc malicious-signature-database 1 name "SIPScan" pattern "Header.User-Agent.content prefix 'sip-scan'" activate exit sbc malicious-signature-database 2



name "Smap" pattern "Header.User-Agent.content prefix 'smap'" activate exit sbc malicious-signature-database 3 name "Sipsak" pattern "Header.User-Agent.content prefix 'sipsak'" activate exit sbc malicious-signature-database 4 name "Sipcli" pattern "Header.User-Agent.content prefix 'sipcli'" activate exit sbc malicious-signature-database 5 name "Sivus" pattern "Header.User-Agent.content prefix 'SIVuS'" activate exit sbc malicious-signature-database 6 name "Gulp" pattern "Header.User-Agent.content prefix 'Gulp'" activate exit sbc malicious-signature-database 7 name "Sipv" pattern "Header.User-Agent.content prefix 'sipv'" activate exit sbc malicious-signature-database 8 name "Sundayddr Worm" pattern "Header.User-Agent.content prefix 'sundayddr'" activate exit sbc malicious-signature-database 9 name "VaxIPUserAgent" pattern "Header.User-Agent.content prefix 'VaxIPUserAgent'" activate exit sbc malicious-signature-database 10 name "VaxSIPUserAgent" pattern "Header.User-Agent.content prefix 'VaxSIPUserAgent'" activate exit sbc malicious-signature-database 11 name "SipArmyKnife" pattern "Header.User-Agent.content prefix 'siparmyknife'" activate



exit

ldap ldap-search-server-method sequentialy activate exit

sip-definition settings ldap-primary-key "telephoneNumber" activate exit

sip-definition proxy-and-registration authentication-mode per-endpoint enable-proxy use-proxy enable-registration on activate exit

sip-definition proxy-and-registration authentication-mode per-endpoint enable-proxy use-proxy enable-registration on activate exit

International Headquarters 1 Hayarden Street, Airport City Lod 7019900, Israel Tel: +972-3-976-4000 Fax: +972-3-976-4040 AudioCodes Inc. 27 World’s Fair Drive, Somerset, NJ 08873 Tel: +1-732-469-0880 Fax: +1-732-469-2298 Contact us: www.audiocodes.com/contact Website: www.audiocodes.com ©2017 AudioCodes Ltd. All rights reserved. AudioCodes, AC, HD VoIP, HD VoIP Sounds Better, IPmedia, Mediant, MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice and CloudBond are trademarks or registered trademarks of AudioCodes Limited. All other products or trademarks are property of their respective owners. Product specifications are subject to change without notice. Document #: LTRT-23304

http://www.audiocodes.com/contact

http://www.audiocodes.com/

mediant msbr - audiocodes...when upgrade is performed from version 6.8 to version 7.2 and the...

Documents