Repair Instructions for

TRAILER ABS – Enhanced Easy Stop

1

SID003FMI001

SAE Fault Code: SID 3 FMI 1

Description: Sensor BU1 – Air gap too large The ABS ECU has detected that the sensor is not producing a large enough signal. Push the sensor in until it touches the tooth wheel. Trailer Sensor Installation

2

SID003FMI002

SAE Fault Code: SID 3 FMI 2

Description: Sensor BU1 – Wheel Speed Difference The ABS ECU has detected a Wheel Speed Difference. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel. Push sensor all the way in until it touches the tooth wheel. Check wheel-end bearing adjustment. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

3

SID003FMI003

SAE Fault Code: SID 3 FMI 3

Description: Sensor BU1 – Shorted to 12 Volts The ABS ECU has detected that the sensor wiring has 12 Volts on it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer ABS Schematic Diagram Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

4

SID003FMI004

SAE Fault Code: SID 3 FMI 4

Description: Sensor BU1 – Shorted to ground The ABS ECU has detected that the sensor wire is shorted to ground. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components Trailer Installation Diagrams

5

SID003FMI005

SAE Fault Code: SID 3 FMI 5

Description: Sensor BU1 – Open circuit The ABS ECU has detected that the sensor wires or the sensor itself has an open in it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

6

SID003FMI006

SAE Fault Code: SID 3 FMI 6

Description: Sensor BU1 – Open or short circuit The ABS ECU has detected that the sensor wire is open or shorted. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

7

SID003FMI007

SAE Fault Code: SID 3 FMI 7

Description: Sensor BU1 – Tone wheel defect The ABS ECU has detected an erratic sensor signal that may be caused by a defective tone wheel. Examine the tone wheel for damaged/missing teeth, or wheel-end bearing adjustment causing run out. Trailer Sensor Installation Trailer Main Components

8

SID003FMI008

SAE Fault Code: SID 3 FMI 8

Description: Sensor BU1 – Wheel slip failure The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

9

SID003FMI009

SAE Fault Code: SID 3 FMI 9

Description: Sensor BU1 – No speed detected The ABS ECU has detected that the sensor is producing no signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

10

SID003FMI010

SAE Fault Code: SID 3 FMI 10

Description: Sensor BU1 – Erratic speed signal The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel or wheel-end bearing adjustment causing run out. Trailer Sensor Installation Trailer Main Components

11

SID003FMI011

SAE Fault Code: SID 3 FMI 11

Description: Sensor BU1 – Chattering The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

12

SID003FMI012

SAE Fault Code: SID 3 FMI 12

Description: Sensor BU1 – Bad Device or Component The ABS ECU has detected an internal error. Check the sensor cable for pinching or cuts and check connectors. If ok, call Meritor WABCO for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

13

SID004FMI001

SAE Fault Code: SID 4 FMI 1

Description: Sensor YE1 – Air gap too large The ABS ECU has detected that the sensor is not producing a large enough signal. Push the sensor in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

14

SID004FMI002

SAE Fault Code: SID 4 FMI 2

Description: Sensor YE1 – Wheel Speed Difference The ABS ECU has detected Wheel Speed Difference. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel, or wheel-end bearing adjustment causing run out. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

15

SID004FMI003

SAE Fault Code: SID 4 FMI 3

Description: Sensor YE1 – Shorted to 12 Volts The ABS ECU has detected that the sensor wiring has 12 Volts on it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

16

SID004FMI004

SAE Fault Code: SID 4 FMI 4

Description: Sensor YE1 – Shorted to ground The ABS ECU has detected that the sensor wire is shorted to ground. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

17

SID004FMI005

SAE Fault Code: SID 4 FMI 5

Description: Sensor YE1 – Open circuit The ABS ECU has detected that the sensor wires or the sensor itself has an open in it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer Main Components

18

SID004FMI006

SAE Fault Code: SID 4 FMI 6

Description: Sensor YE1 – Open or short circuit The ABS ECU has detected that the sensor wire is open or shorted. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

19

SID004FMI007

SAE Fault Code: SID 4 FMI 7

Description: Sensor YE1 – Tone wheel defect The ABS ECU has detected an erratic sensor signal that may be caused by a defective tone wheel. Examine the tone wheel for damaged or missing teeth. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

20

SID004FMI008

SAE Fault Code: SID 4 FMI 8

Description: Sensor YE1 – Wheel slip failure The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

21

SID004FMI009

SAE Fault Code: SID 4 FMI 9

Description: Sensor YE1 – No speed detected The ABS ECU has detected that the sensor is producing no signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

22

SID004FMI010

SAE Fault Code: SID 4 FMI 10

Description: Sensor YE1 – Erratic speed signal The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel, or check wheel-end bearing adjustment causing run out. Trailer Sensor Installation Trailer Main Components

23

SID004FMI011

SAE Fault Code: SID 4 FMI 11

Description: Sensor YE1 – Chattering The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

24

SID004FMI012

SAE Fault Code: SID 4 FMI 12

Description: Sensor YE1 – Bad Device or Component The ABS ECU has detected an internal error. Check the sensor cable for pinching or cuts and check connectors. If ok, call Meritor WABCO for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

25

SID005FMI001

SAE Fault Code: SID 5 FMI 1

Description: Sensor BU2 – Air gap too large The ABS ECU has detected that the sensor is not producing a large enough signal. Push the sensor in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

26

SID005FMI002

SAE Fault Code: SID 5 FMI 2

Description: Sensor BU2 – Wheel Speed Difference The ABS ECU has detected Wheel Speed Difference. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel, or check wheel-end bearing adjustment causing run out. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

27

SID005FMI003

SAE Fault Code: SID 5 FMI 3

Description: Sensor BU2 – Shorted to 12 Volts The ABS ECU has detected that the sensor wiring has 12 Volts on it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

28

SID005FMI004

SAE Fault Code: SID 5 FMI 4

Description: Sensor BU2 – Shorted to ground The ABS ECU has detected that the sensor wire is shorted to ground. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

29

SID005FMI005

SAE Fault Code: SID 5 FMI 5

Description: Sensor BU2 – Open circuit The ABS ECU has detected that the sensor wires or the sensor itself has an open in it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer Main Components

30

SID005FMI006

SAE Fault Code: SID 5 FMI 6

Description: Sensor BU2 – Open or short circuit The ABS ECU has detected that the sensor wire is open or shorted. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

31

SID005FMI007

SAE Fault Code: SID 5 FMI 7

Description: Sensor BU2 – Tone wheel defect The ABS ECU has detected an erratic sensor signal that may be caused by a defective tone wheel. Examine the tone wheel for damaged or missing teeth. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

32

SID005FMI008

SAE Fault Code: SID 5 FMI 8

Description: Sensor BU2 – Wheel slip failure The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

33

SID005FMI009

SAE Fault Code: SID 5 FMI 9

Description: Sensor BU2 – No speed detected The ABS ECU has detected that the sensor is producing no signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

34

SID005FMI010

SAE Fault Code: SID 5 FMI 10

Description: Sensor BU2 – Erratic speed signal The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel, or wheel-end bearing adjustment causing run out. Trailer Sensor Installation Trailer Main Components

35

SID005FMI011

SAE Fault Code: SID 5 FMI 11

Description: Sensor BU2 – Chattering The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

36

SID005FMI012

SAE Fault Code: SID 5 FMI 12

Description: Sensor BU2 – Bad Device or Component The ABS ECU has detected an internal error. Check the sensor cable for pinching or cuts and check connectors. If ok, call Meritor WABCO for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

37

SID005FMI014

SAE Fault Code: SID 5 FMI 14

Description: Sensor BU2 – Sensor not found The ABS ECU has detected an unexpected system. The configuration is not as expected. An external valve or two sensors are not being detected. Connect them or reconfigure the ECU to the new system using the reconfigure option from the Toolbox menu. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

38

SID006FMI001

SAE Fault Code: SID 6 FMI 1

Description: Sensor YE2 – Air gap too large The ABS ECU has detected that the sensor is not producing a large enough signal. Push the sensor in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

39

SID006FMI002

SAE Fault Code: SID 6 FMI 2

Description: Sensor YE2 – Wheel Speed Difference The ABS ECU has detected Wheel Speed Difference. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel, or wheel-end bearing adjustment causing run out. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

40

SID006FMI003

SAE Fault Code: SID 6 FMI 3

Description: Sensor YE2 – Shorted to 12 Volts The ABS ECU has detected that the sensor wiring has 12 Volts on it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

41

SID006FMI004

SAE Fault Code: SID 6 FMI 4

Description: Sensor YE2 – Shorted to ground The ABS ECU has detected that the sensor wire is shorted to ground. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

42

SID006FMI005

SAE Fault Code: SID 6 FMI 5

Description: Sensor YE2 – Open circuit The ABS ECU has detected that the sensor wires or the sensor itself has an open in it. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer Main Components

43

SID006FMI006

SAE Fault Code: SID 6 FMI 6

Description: Sensor YE2– Open or short circuit The ABS ECU has detected that the sensor wire is open or shorted. Check the sensor wiring and connectors for damage. The resistance of the sensor should be between 500 and 2000 ohms. Replace sensor if the resistance reading is out of this range. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

44

SID006FMI007

SAE Fault Code: SID 6 FMI 7

Description: Sensor YE2 – Tone wheel defect The ABS ECU has detected an erratic sensor signal that may be caused by a defective tone wheel. Examine the tone wheel for damaged or missing teeth. Trailer Sensor Installation Trailer ABS Schematic Diagram Trailer Main Components

45

SID006FMI008

SAE Fault Code: SID 6 FMI 8

Description: Sensor YE2 – Wheel slip failure The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Check for damaged teeth on the tooth wheel. Push sensor all the way in until it touches the tooth wheel. Trailer Sensor Installation Trailer Main Components

46

SID006FMI009

SAE Fault Code: SID 6 FMI 9

Description: Sensor YE2 – No speed detected The ABS ECU has detected that the sensor is producing no signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

47

SID006FMI010

SAE Fault Code: SID 6 FMI 10

Description: Sensor YE2 – Erratic speed signal The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel, or wheel-end bearing adjustment causing run out. Trailer Sensor Installation Trailer Main Components

48

SID006FMI011

SAE Fault Code: SID 6 FMI 11

Description: Sensor YE2 – Chattering The ABS ECU has detected that the sensor is producing an erratic signal. Check for loose sensor connectors on the ECU and on the extension cables. Push sensor all the way in until it touches the tooth wheel. Check for damaged teeth on the tooth wheel. Trailer Sensor Installation Trailer Main Components

49

SID006FMI012

SAE Fault Code: SID 6 FMI 12

Description: Sensor YE2 – Bad Device or Component The ABS ECU has detected an internal error. Check the sensor cable for pinching or cuts and check connectors. If ok, call Meritor WABCO for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

50

SID006FMI014

SAE Fault Code: SID 6

FMI 14 Description: Sensor YE2 – Sensor not found The ABS ECU has detected an unexpected system. The configuration is not as expected. An external valve or two sensors are not being detected. Connect them or reconfigure the ECU to the new system using the reconfigure option from the Toolbox menu. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

51

SID007FMI003

SAE Fault Code: SID 7 FMI 3

Description: External Modulator Valve (RED) – short to 12 volts The ABS ECU has detected a short to 12 volts on the RED external modulator valve. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

52

SID007FMI004

SAE Fault Code: SID 7 FMI 4

Description: External Modulator Valve (RED) – short to ground The ABS ECU has detected a short to ground on the RED external modulator valve. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

53

SID007FMI005

SAE Fault Code: SID 7 FMI 5

Description: External Modulator Valve (RED) – Open circuit The ABS ECU has detected an open circuit on the RED external modulator valve. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

54

SID007FMI006

SAE Fault Code: SID 7 FMI 6

Description: External Modulator Valve (RED) – short to ground The ABS ECU has detected a short to ground on the RED external modulator valve. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

55

SID007FMI012

SAE Fault Code: SID 7 FMI 12

Description: External Modulator Valve (RED) – Failure The ABS ECU has detected a failure in the RED valve circuit. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

56

SID007FMI014

SAE Fault Code: SID 7 FMI 14

Description: External Modulator Valve (RED) – not found The ABS ECU has not detected the external red valve. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

57

SID009FMI003

SAE Fault Code: SID 9 FMI 3

Description: Modulator Valve (BLUE) – short to 12 volts The ABS ECU has detected a short to 12 volts on the BLUE modulator valve. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

58

SID009FMI004

SAE Fault Code: SID 9 FMI 4

Description: Modulator Valve (BLUE) – short to ground The ABS ECU has detected a short to ground on the BLUE modulator valve. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

59

SID009FMI005

SAE Fault Code: SID 9 FMI 5

Description: Modulator Valve (BLUE) – Open circuit The ABS ECU has detected an open circuit on the BLUE modulator valve. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

60

SID009FMI006

SAE Fault Code: SID 9 FMI 6

Description: Modulator Valve (BLUE) – short to ground The ABS ECU has detected a short to ground on the BLUE modulator valve. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

61

SID009FMI012

SAE Fault Code: SID 9 FMI 12

Description: Modulator Valve (BLUE) – Failure The ABS ECU has detected a failure in the BLUE valve circuit. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

62

SID010FMI003

SAE Fault Code: SID 10 FMI 3

Description: ECU/Valve (YELLOW) – short to 12 volts The ABS ECU has detected a short to 12 volts on the ECU/Valve assembly. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

63

SID010FMI004

SAE Fault Code: SID 10 FMI 4

Description: ECU/Valve (YELLOW) – short to ground The ABS ECU has detected a short to ground on the ECU/Valve assembly. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

64

SID010FMI005

SAE Fault Code: SID 10 FMI 5

Description: ECU/VALVE (YELLOW) – Open circuit The ABS ECU has detected an open circuit on the ECU/Valve assembly. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

65

SID010FMI006

SAE Fault Code: SID 10 FMI 6

Description: ECU/VALVE ASSEMBLY – short to ground The ABS ECU has detected a short to ground on the ECU/Valve assembly. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

66

SID010FMI012

SAE Fault Code: SID 10 FMI 12

Description: ECU/VALVE ASSEMBLY – Failure The ABS ECU has detected a failure in the ECU/VALVE Assembly. Check the external valve cable and connectors. If cable is ok, call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

67

SID011FMI003

SAE Fault Code: SID 11 FMI 3

Description: Internal solenoid – short to 12 volts The ABS ECU has detected a short to 12 volts on the internal solenoid. Call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

68

SID011FMI004

SAE Fault Code: SID 11 FMI 4

Description: Internal solenoid – short to ground The ABS ECU has detected a short to ground on the internal solenoid. Call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

69

SID011FMI005

SAE Fault Code: SID 11 FMI 5

Description: Internal solenoid – Open circuit The ABS ECU has detected an open circuit on the internal solenoid. Call Meritor WABCO customer support for technical support and return authorization claim number. Trailer Main Components Meritor WABCO Customer Service

70

SID014FMI002

SAE Fault Code: SID 14 FMI 2

Description: Unexpected System Configuration Detected The ABS ECU has detected a system configuration other than what it expected. An external valve or two sensors are not being detected. Connect them or reconfigure the ECU using the reconfigure option from the Toolbox Software menu. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

71

SID014FMI003

SAE Fault Code: SID 14 FMI 3

Description: Power Supply Over Voltage The ABS ECU has detected an over voltage condition on the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

72

SID014FMI004

SAE Fault Code: SID 14 FMI 4

Description: Power Supply Under Voltage The ABS ECU has detected an under voltage condition on the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU.

73

Trailer ABS Schematic Diagram

SID014FMI005

SAE Fault Code: SID 14 FMI 5

Description: Power Supply Low Current Detected The ABS ECU has detected a low current condition from the power supply. Check that all the power and ground connections are solid. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

74

SID014FMI009

SAE Fault Code: SID 14 FMI 9

Description: ECU Valve Assembly Internal Fault The ABS ECU has detected an internal fault in the ECU Valve Assembly. Clear the faults with Toolbox. Turn the ignition off and then back on. If the fault repeats, call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

75

SID014FMI012

SAE Fault Code: SID 14 FMI 12

Description: ECU Valve Assembly Internal Fault The ABS ECU has detected an internal fault in the ECU Valve Assembly. Clear the faults with Toolbox. Turn the ignition off and then back on. If the fault repeats, call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

76

SID015FMI009

SAE Fault Code: SID 15 FMI 9

Description: Electromagnetic Interference Detected The ABS ECU has detected a EMI fault. Call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

77

SID015FMI012

SAE Fault Code: SID 15 FMI 12

Description: ECU Valve Assembly Internal Fault The ABS ECU has detected an internal fault in the ECU Valve Assembly. Clear the faults with Toolbox. Turn the ignition off and then back on. If the fault repeats, call Meritor WABCO customer support for technical support and return authorization claim number. Meritor WABCO Customer Service

78

SID059FMI001

SAE Fault Code: SID 59 FMI 1

Description: ECU Power Supply Low Voltage The ABS ECU has detected a low voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

79

SID059FMI003

SAE Fault Code: SID 59 FMI 3

Description: ECU Power Supply High Voltage The ABS ECU has detected a high voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

80

SID059FMI004

SAE Fault Code: SID 59 FMI 4

Description: ECU Power Supply Low Voltage The ABS ECU has detected a low voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

81

SID059FMI008

SAE Fault Code: SID 59 FMI 8

Description: Intermittent Stop Light Power The ABS ECU has detected a low voltage fault in the power supply on the stop light power line. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

82

SID059FMI009

SAE Fault Code: SID 59 FMI 9

Description: ECU Power Supply Internal Fault The ABS ECU has detected an internal fault in the power supply. Call Meritor WABCO for customer support and a return authorization claim number.

83

Meritor WABCO Customer Service

SID059FMI010

SAE Fault Code: SID 59 FMI 10

Description: ECU Power Supply Intermittent Contact The ABS ECU has detected a low voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

84

SID059FMI012

SAE Fault Code: SID 59 FMI 12

Description: ECU Power Supply Internal Fault The ABS ECU has detected an internal fault in the power supply. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

85

SID059FMI014

SAE Fault Code: SID 59 FMI 14

Description: ECU Power Supply Impedance Failure The ABS ECU has detected an impedance failure in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

86

SID060FMI002

SAE Fault Code: SID 60 FMI 2

Description: Unexpected System Detected The ABS ECU has detected an unexpected system. The configuration is not as expected. An external valve or two sensors are not being detected. Connect them or reconfigure the ECU to the new system using the reconfigure option from the Toolbox menu. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

87

SID061FMI002

SAE Fault Code: SID 61 FMI 2

Description: ECU Calibration Parameter Failure The ABS ECU has detected an error in the parameters inside the ECU memory. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

88

SID061FMI012

SAE Fault Code: SID 61 FMI 12

Description: ECU Calibration Memory Internal Fault The ABS ECU has detected an error in the parameters inside the ECU memory. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

89

SID061FMI014

SAE Fault Code: SID 61 FMI 14

Description: ECU Calibration End of Line Test Invalid The ABS ECU has detected an error in the parameters inside the ECU memory. Call Meritor WABCO for customer support and a return authorization claim number.

90

Meritor WABCO Customer Service

SID062FMI002

SAE Fault Code: SID 62 FMI 2

Description: ECU Internal Fault The ABS ECU has detected an internal fault inside the ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

91

SID062FMI012

SAE Fault Code: SID 62 FMI 12

Description: ECU Internal Fault The ABS ECU has detected an internal fault inside the ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

92

SID062FMI015

SAE Fault Code: SID 62 FMI 15

Description: ECU Internal Fault The ABS ECU has detected an internal fault inside the ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

93

SID219FMI002

SAE Fault Code: SID 219 FMI 2

Description: SAE J2497 Broadcast Breakdown The ABS ECU has detected a problem sending messages on the 12 volt power line (PLC). The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Call Meritor WABCO for customer support and a return authorization claim number. Trailer ABS Schematic Diagram Meritor WABCO Customer Service

94

SID219FMI015

SAE Fault Code: SID 219 FMI 15

Description: SAE J2497 Failure The ABS ECU has detected a problem sending messages on the 12 volt power line (PLC). The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

95

SID250FMI015

SAE Fault Code: SID 250 FMI 15

Description: SAE J1708 Data Bus Failure The ABS ECU has detected a problem sending messages on J1708 communications bus. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

96

SID251FMI001

SAE Fault Code: SID 251 FMI 1

Description: ECU Power Supply Low Voltage The ABS ECU has detected a low voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

97

SID251FMI003

SAE Fault Code: SID 251 FMI 3

Description: ECU Power Supply High Voltage The ABS ECU has detected a high voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

98

SID251FMI004

SAE Fault Code: SID 251 FMI 4

Description: ECU Power Supply Low Voltage The ABS ECU has detected a low voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

99

SID251FMI008

SAE Fault Code: SID 251 FMI 8

Description: Intermittent Stop Light Power The ABS ECU has detected a low voltage fault in the power supply on the stop light power line. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

100

SID251FMI009

SAE Fault Code: SID 251 FMI 9

Description: ECU Power Supply Internal Fault The ABS ECU has detected an internal fault in the power supply. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

101

SID251FMI010

SAE Fault Code: SID 251 FMI 10

Description: ECU Power Supply Intermittent Contact The ABS ECU has detected a low voltage fault in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

102

SID251FMI012

SAE Fault Code: SID 251 FMI 12

Description: ECU Power Supply Internal Fault The ABS ECU has detected an internal fault in the power supply. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

103

SID251FMI014

SAE Fault Code: SID 251 FMI 14

Description: ECU Power Supply Impedance Failure The ABS ECU has detected an impedance failure in the power supply. The battery voltage must be between 9.5 and 14.0 volts at the ABS ECU. Trailer ABS Schematic Diagram

104

SID252FMI002

SAE Fault Code: SID 252 FMI 2

Description: Unexpected System Detected The ABS ECU has detected an unexpected system. The configuration is not as expected. An external valve or two sensors are not being detected. Connect them or reconfigure the ECU to the new system using the reconfigure option from the Toolbox menu. Trailer Sensor Installation Trailer Main Components Trailer Installation Diagrams

105

SID253FMI002

SAE Fault Code: SID 253 FMI 2

Description: ECU Calibration Parameter Failure The ABS ECU has detected an error in the parameters inside the ECU memory. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

106

SID253FMI012

SAE Fault Code: SID 253 FMI 12

Description: ECU Calibration Memory Internal Fault The ABS ECU has detected an error in the parameters inside the ECU memory. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

107

SID253FMI014

SAE Fault Code: SID 253 FMI 14

Description: ECU Calibration End of Line Test Invalid The ABS ECU has detected an error in the parameters inside the ECU memory. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

108

SID254FMI002

SAE Fault Code: SID 254 FMI 2

Description: ECU Internal Fault The ABS ECU has detected an internal fault inside the ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

109

SID254FMI012

SAE Fault Code: SID 254 FMI 12

Description: ECU Internal Fault The ABS ECU has detected an internal fault inside the ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

110

SID254FMI015

SAE Fault Code: SID 254 FMI 15

Description: ECU Internal Fault The ABS ECU has detected an internal fault inside the ECU. Call Meritor WABCO for customer support and a return authorization claim number. Meritor WABCO Customer Service

111

Trailer ABS Schematic Diagram

112

Trailer Main Components

1. ECU Valve Assembly 2. External ABS Modulator Valve (3M Configuration) 1. Exhaust Solenoid 3. Tooth Wheel 2. Inlet Solenoid 4. Wheel Speed Sensor 3. Ground

113

Trailer Sensor Installation

1. Sensor Holder 2. Sensor Clip 3. Sensor Clip Tab 4. Sensor

1. Sensor Cable Installed

114

Meritor WABCO Customer Service

115

Trailer Installation Diagrams

Select appropriate ECU and configuration for diagram

2S/1M Basic: Spring/Air 2S/2M Standard: Sensors Facing Front (side to side control) 2S/2M Standard: Sensors Facing Rear (side to side control) 2S/2M Premium: Sensors Facing Front/Rear (side to side control) 4S/2M Premium: Sensors Facing Front/Rear (side to side control) 4S/2M Premium: Axle Control Sensors Facing Front/Rear 4S/3M Premium: Tri-Axle W/Front Lift Sensors Facing Front/Rear 4S/3M Premium: Tri-Axle Sensors Facing Front/Rear 4S/3M Premium: Four Axle Pull Trailer Sensors Facing Front/Rear

116

2S/1M Basic: Spring/Air

117

2S/2M Standard: Sensors Facing Front

118

2S/2M Standard: Sensors Facing Rear

119

2S/2M Premium: Sensors Facing Front/Rear

120

4S/2M Premium: Sensors Facing Front/Rear

121

4S/2M Premium: Tri-Axle Sensors Facing Front/Rear

122

4S/2M Premium: Axle Control Sensors Facing Front/Rear

123

4S/3M Premium: Tri-Axle W/Front Lift Sensors Facing Front/Rear

124

4S/3M Premium: Tri-Axle Sensors Facing Front/Rear

125

4S/3M Premium: Four Axle Pull Trailer Sensors Facing Front/Rear

126

SAE Fault Code: SID UNK FMI UNK

Description: Unknown SID/FMI

The ABS ECU has reported a System ID and Failure Mode Identifier that is not recognized by this document. Please contact ArvinMeritor’s Customer Service Center

800-535-5560.

127