Model:CFN-1007

Unpack your fan and check the contents. You should have the following items:

d

e

h

l

i

k

a

b

c

a. Fan blades (3) b. Ceiling mounting bracket c. Canopyd. Ball/downrod assemblye. Coupling cover f. Fan motor assembly

l. Part bag contents 1) Mounting hardware : wood screws (2), flat washers (2), star washers (2), wire nuts (8 ), screws (2) 2) Blade attachment hardware: screws (10 ), fiber washers (10 ) 3) Blade brackets hardware: screws (1)

4) Balance Kit

f

g

g. light plate

h. led light kiti. glass shadej. hand held remote control system

k. receiver with 5 wire nuts

j

MED

HILOW

STOP

2H

4H1H

R/F

LI

Downrod

Canopy

Canopy cover

Set screws

Hitch pin Retaining clip

Coupling cover

Fig 5

Fig 6

5

9

8

9

Fig 8

White (neutral)

White (neutral)

Green or bare copper (ground)

White ("AC IN N")

White ("to motor N")

Ground(green)

Outlet box

Black (hot)

Black ("AC IN L")

Black ("to motor L")

Receiver

Blue (for light)

Blue (for light)

Black (motor)Orange

Red (for forward and reverse L)

Orange (for forward and reverse N)

Red (for forward and reverse L)

(for forward and reverse N)

10

blade

Step 1. Remove 3 preassembled screws andfiber washer from blade bracket, and save it for later use, then insert blade through one ofthe slots from the flywheel. Align holes from blade bracket and blade and secure with just just moved screws and fiber wahser.Tighten each screws.

Step 2. Repeat for the remaining blades.

Step 3. Make sure the blade is straight and tighten each screw.

NOTE: Before starting installation, disconnect

the power by turning off the circuit breaker or

removing the fuse at fuse box.

DO NOT OVERTIGHTEN.

9. INSTALLING THE LED LIGHT KIT

AND LAMP SHADE

Wire connectors

Light plate

LED light kit

Step 3... Raise the glass shade against the LED light kit

and turn clockwise until snug(fig.11).

Glass shade

Screws

Step 1. Loosen the two screws on the mounting ring attached to the motor shaft and "remove" Place the key hole slots on the light plate over the two screws previously loosended on the mounting ring.and save the third screw.then turn the light plate until is locks in place at the narrow section of the key hole slots.Finallytighten both key hole screws and replace the third

screw previously removed and tighten securely.(Fig.11)

Step 2. While holding the LED light kit under the fan

motor, make the wire connections:(Fig. 11)

Blue to Blue. White to White.

Then place the LED light kit onto the light plate by

magnet (Fig. 11)

Fig 11

11. Operation for remote

MED

HILOW

STOP

2H

4H1H

R/F

LI

Installation of transmitter wall

Mount holder with two screws.

1. speed control button of fan: HI. MED AND LOW are speed button.2. LI :ON/OFF the lamp3. STOP :Turn off the ceiling fan.4. Fan timing button: 1H.2H and 4H.5. F/R : Controls the direction of the fan "Forward and Reverse".6. Battery for RF emitter: 12V 23A Bettery foremitter:UM-44 AAARo3 DC 1.5Vx2.7. RF emitter:Renote control distance at 25-30 meters. emitter:Remote control distance within 10 meters.

KINDLY REMINDERS:

Learning code maching mode is useed between emitter and receiver,Turn "ON" the supply power

within 30 seconds and press the emitter's "LI" and "Hi"button for 3 seconds, it can load normally

after hearing the "BEE" which means learning successfully and it can works normally.(PS:Learing

mode is not acepted after turn "ON" the supply power for 30 seconds)

REDTO FAN REVERSE L

TO FAN REVERSE NORANGE

12.TROUBLESHOOTING