more inputs - 7
TRANSCRIPT
More inputs - 7More recipient numbers - 10More base stations - 4More timers - 64More functions- DSC panel controls- SMS command shortcuts- Advanced “if-this-then-that” functions- Unit programming access protection- Intuitive message distributionNew I/O expander moduleNew programming software
Send messages to up to 4 base stations
Speed up Contact ID reporting withoutcompromising compatibility.
The internet of things is here.Send commands from one device toanother to perform complex functions.
Available as a panic pack or power packfor load shedding conditions
+ Bases + Packs
+ more
Connect serially to a DSC alarm panelto arm and disarm by SMS command.
SMS Technology
Intuitive unit status screen
+ More inputs and outputs
+ I/O expander module
+ New intuitive software
Relay 2 Relay 1
Serial connection / to I/O expander
Mains fail/restore
TIP (to alarm panel Telco jack)
Input 7
Input 6
Input 5
Input 4
Input 3
Input 2
Input 1
- DC supply & RING
+12V DC supply
AC bypass jumper
CIDjumper
+-
IP1
IP2
IP3
IP4
IP5
IP6
IP7
TIP
AC
TES
T
PWR
GSM
SYS
SIM
2S
IM1
CO
MM
SNC NO CM NC NO CM
PrimarySIM
To SMX
Jumper on = 4/20mAJumper of f = 0 - 10V
IP 8
Sta
tus
IP 9
Aux
Ser
ial
SM
X
NC NO CM NC NO CM NC NO CM
CM NO NC CM NO NC CM NO NC
12V DC
Positive
Input 9
Input 8
Optically isolated
NegativePO
SN
EG
8
A/D
9Relay 8
Relay 5
Relay 7
Relay 4
Relay 6
Relay 3
SIM setup
STEP 1 Disable SIM card PIN/sInsert SIM card/s into any mobile phone and disable the SIM PIN/sbefore installation (see phone instructions).
Primary SIM
Secondary SIM
Mobile operator
Mobile operator
Vodacom
Enter manually
98273649287346 Message center number
Message center number
STEP 3Select operator/s message centreThe network provider's SMS message center number must be set for eachSIM in order to send SMS's.
SIM
2S
IM1
Enable
STEP 2 Single SIM card operation Ensure SIM card is inserted intoprimary SIM card holder (SIM 1).
MACHINE TO MACHINE
Sort different SIM pads
Check SIM positions
Read ConfigurationSave as template Write ConfgurationLoad template
SETUP
Security setup
SMS MESSAGING
General setup
Message recipients
Input SMS messages
Distribute messages
Contact ID
SWITCHING - relays
SMS commands shortcuts
Missed call switching
Switching by timer
SMX to base stations
If-this-then-that
View unit status
Pulse time setup
SIM setup
0-10 V4-20
Status
2closed
1open
ConnectedVodacom Firmware V2.12IMSI 86955103002814200 IMEI 351756051523999
Good
Excellent
Poor
Active SIM - select
11.9V
Supply
Relays
12
1 2 3 4 5 6 7 AC
Inputs - high low
Main menu
Relays
POS NEG 8 9
12V DC Isolated inputs
5open
4closed
3closed
8closed
7open
6closed
Analogue input
A/D
-.-12 mA
I/O expander
SMS Technology
Specifications
GSMFrequency bands Dual band (GSM 900MHz/1800MHz)Output power Class 4 for EGSM900, Class 1 for GSM1800Engine BGS2-E/BGS2-W Cinterion
Power consumptionStandby 1.08Watt (0.09mA @ 12V)Input voltage 9Vdc(min) to 25Vdc(max)
PhysicalDimensions 140mm (without antenna) x 100mm x 30mmMounting 2 x 4.7mm holes on the enclosureWeight 165grams
Input and output specificationsInputs Positive trip +2.7V to +30V Negative trip -0.5V to +0.5VOutputs 10A @ 250Vac max 10A @ 28Vdc max
Input and output connectionsInputs - 9 Hardwired screw terminal inputs (Input 9 shared with CID input) - 1 AC fail screw terminal input - TTL serial communications connector - Engineer test buttonOutputs - 2 Relay screw terminal outputs (CM, NO, NC)
SMS Technology
Contact
www.radiodata.co.za+27 11 452 1471+27 11 452 1503havens.outwit.bets 1st floor, Senet House,157 van Riebeeck Ave, Edenvale.S: 26° 07’ 791E: 28° 08’ 81Postnet Suite 79Private Bag [email protected]+27 82 444 7176Brent [email protected]: brent.andrekaLee-Ann [email protected]: leeann.andreka
WebsiteSwitchboard Fax What3words Physical address
Postal address Sales24hr Technical Standby Managing Director Chief Industry Advisor