mosa 4600b sip line user manual v6 english - … · 7.3.1 configure mosa 3700 as client ... sip...

MOSA 4600B SIP Line

User Manual

Edition 6.0

Update：2005/08/29

DCC NO. 9171003506

MOSA 4600B SIP Line user manual

1

Table of Contents

1. Safety Instructions.................................................................................................................. 7

2. Features ................................................................................................................................... 8

3. Package Contents ................................................................................................................... 9

4. Introduction ........................................................................................................................... 10 4.1 Panel............................................................................................................................... 10

4.1.1 Front Panel.............................................................................................................. 10 4.1.2 Rear Panel .............................................................................................................. 10

4.2 LED indicator ..................................................................................................................11 4.3 Connector ...................................................................................................................... 12

5. Basic Configuration .............................................................................................................. 13 5.1 Console Configuration.................................................................................................. 13

6. Configuration of Functions .................................................................................................. 14 6.1 General configuration ................................................................................................... 14

6.1.1 Configuration of IP................................................................................................... 14 6.2 Basic parameter configuration .................................................................................... 16

6.2.1 Configure My Phone Number.................................................................................. 17 6.2.2 Registration of NETMOSA and/or NETMOSA Plus................................................. 18

6.3 Basic Structure.............................................................................................................. 19 6.3.1 Client Mode ............................................................................................................. 19 6.3.2 Server Mode............................................................................................................ 20

7. Configuration and Operation of Server Mode .................................................................... 21 7.1 What is Server Mode..................................................................................................... 21 7.2 Configuration of Server Mode...................................................................................... 21

7.2.1 Use STUN Server.................................................................................................... 21 7.2.2 Configure NAT WAN IP and Disable STUN Server ................................................. 22 7.2.3 Configuration of one step dialing DID mode............................................................ 25 7.2.4 Other Necessary Configuration ............................................................................... 26

7.3 How to register for Client ............................................................................................. 29 7.3.1 Configure MOSA 3700 as Client ............................................................................. 29 7.3.2 Configure Other SIP Device as Client ..................................................................... 30

7.4 The Application of Server Mode................................................................................... 33 7.4.1 SIP Extension Map (for Server and Client mode).................................................... 34 7.4.2 Dialing Method ........................................................................................................ 36

7.5 Use Video Call ............................................................................................................... 37 7.5.1 Configuration of MOSA 4600B ................................................................................ 37 7.5.2 Configuration of SIP Client Device .......................................................................... 38 7.5.3 Make Video call ....................................................................................................... 42

8. SIP Network Configuration (Client Mode)........................................................................... 44 8.1 System Configuration ................................................................................................... 44

8.1.1 Select Channel and SIP Entity ................................................................................ 44

2

8.1.2 Configure SIP Proxy and Registrar Server.............................................................. 45 8.1.3 Select Codec Type and Priority ............................................................................... 45 8.1.4 Configure SIP Number ............................................................................................ 46 8.1.5 SIP Outbound Authentication .................................................................................. 46 8.1.6 Configure STUN Server setting or WAN IP ............................................................. 47 8.1.7 Check the registration status of SIP entity............................................................... 48 8.1.8 Contact Address ...................................................................................................... 48 8.1.9 SIP Call Forward ..................................................................................................... 49

8.2 From VODNET to SIP .................................................................................................... 50 8.3 From SIP to VODNET .................................................................................................... 51

8.3.1 Two Step Dialing...................................................................................................... 51 8.3.2 One step dialing DID Mode ..................................................................................... 53

8.4 From VODNET to Different SIP .................................................................................... 54 8.5 Incoming Call from Different SIP Environment .......................................................... 55 8.6 Penetrate Different SIP Environment .......................................................................... 56

8.6.1 From MOSA 4600B SIP Line to MOSA 4600C SIP Trunk ....................................... 57 8.6.2 From MOSA 4600C SIP Trunk to MOSA 4600B SIP Line ....................................... 58

9. SIP Authentication for Incoming Call .................................................................................. 60 9.1 SIP Inbound authentication (for Client and Server mode) ........................................ 60 9.2 Caller ID authentication (for Server Mode only) ......................................................... 61 9.3 PIN code authentication (for Server Mode only) ........................................................ 62

10. VODNET Network Configuration ......................................................................................... 65 10.1 Numbering Plan............................................................................................................. 65

10.1.1 Frequently Used Dialing Example ........................................................................... 66 10.1.2 Exception Dialing Example...................................................................................... 67

10.2 Prefix Map ...................................................................................................................... 68 10.3 VODNET Call Forward................................................................................................... 69

10.3.1 Forward to VODNET ............................................................................................... 70 10.3.2 Configuration of remote MOSA 4600 ...................................................................... 71

10.4 SIP Seize Remote Trunk at VODNET side ................................................................... 72 10.5 Abbreviated Dial ............................................................................................................ 74 10.6 Softkey ........................................................................................................................... 74 10.7 Abbr. Dial Combined with Softkey............................................................................... 75 10.8 MOSA Phone Book........................................................................................................ 76

11. Description of Web Parameter............................................................................................. 78 11.1 Basic\System Config..................................................................................................... 78 11.2 Basic\ABBR. Dial........................................................................................................... 80 11.3 IP Setting........................................................................................................................ 81 11.4 Advanced-MOSA\General............................................................................................. 86 11.5 Advanced-MOSA\Numbering Plan............................................................................... 87 11.6 Advanced-MOSA\PKS................................................................................................... 91 11.7 Advanced-MOSA\Prefix Map ........................................................................................ 92 11.8 Advanced-SIP\Common................................................................................................ 94 11.9 Advanced-SIP\Inbound Auth (Server Mode Only) ...................................................... 98 11.10 Advanced-SIP\Registrar (Server Mode Only) ........................................................... 100 11.11 WAN IP (Client Mode Only)......................................................................................... 101 11.12 Advanced-SIP\Diagnosis ............................................................................................ 102


3

11.13 Channel\Summary....................................................................................................... 103 11.14 Channel\Configuration................................................................................................ 103 11.15 Phone Book ................................................................................................................. 109 11.16 Access Code.................................................................................................................110 11.17 File Transfer\Download................................................................................................113 11.18 File Transfer\Upload.....................................................................................................114 11.19 License Upgrade ..........................................................................................................115

12. Use Private IP Behind NAT..................................................................................................117

13. File Management ..................................................................................................................118 13.1 File Type ........................................................................................................................118 13.2 Download and Modify MEM file...................................................................................118 13.3 Software Upgrade........................................................................................................ 120

13.3.1 Software update via WEB...................................................................................... 120 13.3.2 Software update via FTP ....................................................................................... 121

14. Management by System Console ...................................................................................... 124

15. Specification........................................................................................................................ 125

4

Change History: Software Version 1.06.4

Note: Firmware 1.06 (or above) is for small form model. Standard form model is suspended and no upgrade is available.

Add function: RFC2833 Payload Type is changeable

Change type is not required in normal condition. This function selects suitable RFC2833 Payload Type automatically.

Add PSTN dial in authentication in Client Mode

Add PSTN (mobile phone) dial in Caller ID authentication. This is the special application of mobile extension and not used in normal condition. Please refer to 11.4 Advanced-MOSA\General

Add gain control Gain (volume) control for each channel is available. Please refer to 11.14 Channel\Configuration

Add Progress Tone in Client Mode.

Please refer to 11.4 Advanced-MOSA\General

Update Channel Acccount Name

Default value: Channel 1 = Channel No.: 10 = Extension Number: 1010 = Extension Account: Ext10 Please refer to 7.4.1 SIP Extension Map (for Server and Client mode)

Change History: Software Version 1.06.3 Note: Firmware 1.06 (or above) is for small form model. Standard form model is suspended and no upgrade is

available. Modification: Change default value of Realm

The default Realm of SIP Inbound Authentication is changed from blank to MAC Address. Please refer to 11.9 Advanced-SIP\Inbound Auth (Server Mode Only)

Modification: Change default value of No Answer Forward Time

The default No Answer Forward Time is changed from 50 to 20 seconds. Please refer to 11.4 Advanced-MOSA\General

Add Access Code rule for Caller ID

Add Office Code Exception, Toll Call Exception and Leading Digits of Local Calls field in Access Code Web page for Caller ID control. Please refer to 11.16 Access Code

Add Progress Tone type

Add Progress Tone type: Confirm Tone. Please refer to 11.4 Advanced-MOSA\General

Change History: Software Version 1.06.2 Note: Firmware 1.06 (or above) is for small form model. Standard form model is suspended and no upgrade is

available. Add new button [Register-All] and [DeRegister-All]

In Client Mode, click button to Register-All or DeRegister-All SIP Entities. Please refer to 11.8 Advanced-SIP\Common

Add new security for Web management

Only PC with specified IP or in the same subnet can manage this machine if this function is applied. Please refer to 11.3 IP Setting

Add license upgrade in Web

Use the Key number that purchase from our company, available ports can be increased by upgrade from management web. Please refer to 11.19 License Upgrade

Add Progress Tone function for outbound call.

Can play ring back tone to Calling side before called side at PSTN answers the call. Please refer to 11.4 Advanced-MOSA\General.

Modification: Default Public Address is

Each Entity can has its own Entity number and does not share together. Please refer to 11.8 Advanced-SIP\Common


5

changed From this version, Web file (*.WEB) is divided into Server Mode and Client Mode.

To simplify installation procedure, we delete some parameter that is rare used or OK with default value in web page, and Web file (*.WEB) is also divided into Server Mode and Client Mode. Administrator can upload different web file (*.WEB) to use Server Mode or Client Mode function according to your requirement. If you find the management web of this manual is different from yours, it might be different mode at your machine.

Change History: Software Version 1.06.0 Note: Firmware 1.06 (or above) is for small form factor model. Standard form factor model is suspended and

no upgrade is available. Add Prefix Type: Conf Used in Prefix Number that connects to FONEMOSA 4496. Please refer to 10.2 Prefix

Map Add voice and video Codec

Add voice Codec iLBC and several video Codecs for communication. Please refer to 7.5 Use Video Call

Add max concurrent video call control

Avoid too much bandwidth consumption. Please refer to 11.5 Advanced-MOSA\Numbering Plan

Add Min. Expires Time of SIP registration

Avoid overload of this machine when the same SIP phone repeat request connection status in short period of time. Please refer to 11.10 Advanced-SIP\Registrar

Add video control for each channel

Video call can be enable/disable for each channel. Please refer to 11.14 Channel\Configuration

Add DDNS service This machine can use external DDNS server for IP redirection. Please refer to (Note: For Firmware 1.06.2 or above, DDNS function should be configured on Router that this machine connects to. So this function is removed)

Add network Diagnosis function

For debug purpose. Please refer to 11.12 Advanced-SIP\Diagnosis

# dialing behavior is changed in Conversation State.

For function update. Please refer to 10.1.2 Exception Dialing Example

Change History: Software Version 1.05.0 Support LAN and WAN registration at the same time

SIP device in LAN and WAN can register to this machine at the same time

Built-in G.729 Greeting 8

Greeting music to inform user that use Consult Transfer

Authentication must be the consistent

SIP URI and SIP Inbound Authentication must be the consistent. It reduce complexity of installation

Time sync for SIP device

The system provide GMT time to SIP devices when they do registration

Integrated with FONEMOSA 4489 (Group Ring Server)

It has the ability that personal first extension (Softphone) and second extension (extension on desk) can ring at the same time.

Support pickup function of specified extension.

Function to pick up selected extension. If there is more than one extension is ringing, you can pick up selected extension.

Add function that "X" is equal to the phone number of the

Use "X" to replace the phone number of the machine itself. It reduces the procedure that input again on different field. If the phone number of the machine itself is changed, other field with "X" needs not to change again.

6

machine itself. Add VODNET number as the phone number of itself

If field of phone number is blank and the machine is able to connect Internet, then system input VODNET number automatically.

Change History: Software Version 1.04.0 Enhance Call ID display function

Caller ID from called side is converted to Prefix Number that is easy to identify and call back

Each channel can be assigned to different Pickup group

Many channels version (36, 90 channels) is released, so each channel can assign different group to prevent that pickup group is too large.

Default permission of Outbound Transit becomes International

Easier to configure and test this machine. If strict permission is required, administrator can adjust it manually.

Add new function that upload or download file from Web Page

In addition to FTP download, upload, new features that download and upload file via Web Page is added. It is easier to manage and maintain.

Modify error description

This machine does not support PPPoE IP connection. Original description is removed. Also, modify and add some description in this manual.

Change History: Software Version 1.03.0 Change partial default value

Caller ID become Enable，DID control become Enable and all Channels join SIP Entity 1

Add new function that change Region ID from Web page

Able to change Region ID from Web. It is not necessary to use Console.

Change History: Software Version 1.03.0 First version is released

First version is released


7

1. Safety Instructions

1. Do not attempt to service the product yourself. Any servicing of this product should be referred to qualified service personal.

2. To avoid electric shock, do not put your finger, pin, wire, or any other metal objects into vents and gaps.

3. To avoid accidental fire or electric shock, do not twist power cord or place it under heavy objects.

4. The product should be connected to a power supply of the type described in the operating instructions or as marked on the product.

5. To avoid hazard to children, dispose of the product’s plastic packaging carefully.

6. Please read all the instructions of this manual before using this product, otherwise, it may damage this machine. To simplify installation procedure, this machine is pre-configured most of setting. User should read Quick Installation Guide or Installation Guide of Mobile Office for installation procedure first. Adjust configuration according to this manual if you have advanced requirement.

Warning

8

2. Features SIP VoIP Network is a public VoIP phone structure. Different organization builds different SIP Proxy to provide services. VODNET IP-PBX network is able to provide more powerful and complete calls service than SIP VoIP Network. VODNET IP-PBX network is construct with a series of VODTEL VoIP products and its value-added service.

♦ MOSA 4600B SIP Line is able to register to other SIP Proxy and act as a client (SIP device) of a proxy to provide telephone services, furthermore, it can be configured as a SIP Proxy for other SIP device to register to.

♦ When MOSA 4600B SIP Line acts as a client SIP device, MOSA / FONEMOSA IP-PBX products in VODNET can connect many MOSA 4600B SIP Line to different SIP environment and then bridge the telephone services between VODNET and SIP VoIP network.

♦ By using both MOSA 4600B SIP Line Server and MOSA 4600C SIP Trunk Server, the SIP devices SIP Phone, Softphone) in different environment (means using different SIP proxy) can make call to each other.

♦ MOSA 4600B SIP Line is able to integrate VODNET and many SIP environments. Phone in different environments can make calls to each other as extensions.

♦ When MOSA 4600B SIP Line is configured as Server Mode, other SIP device can register to MOSA 4600B SIP Line as a client. SIP device that register to SIP Line successfully can make call to VODNET or other SIP device (SIP Phone, Soft Phone, SIP gateway). The extension of VODNET can make call to SIP device as other extension.

♦ Use SIP client device that support video function, communication face by face come true and it make communication more real and interesting.

By the integration of MOSA 4600B SIP Line, SIP device (SIP phone, Softphone) is able to use the service of VODNET IP-PBX as below:

♦ Complete IP-PBX function as MOSA 4600 series products

♦ Automatic Call Distribution (ACD, by using ACD Server)

♦ Call Park function (by using Parking Server)

♦ Personal Number function (by using Forward Server)

♦ Bridge to other SIP environment (by using MOSA 4600C SIP Trunk Server with virtual FXO to connect to other environment)

♦ Invite call meeting (by using PBX Conference Bridge)

♦ Conference call center (by using Conference Bridge)

♦ Multiple IP call broadcast (by using Broadcast Server)

♦ Machine with global IP locating function (by using NETMOSA+)

♦ One Ext. No. with many phones (desk phone-set and SIP extension) ringing (Group Ring Server)


9

3. Package Contents

Includes:

The MOSA 4600B SIP Line X 1

Power Core X 1

LAN Cable X 1

Manual / Tools CD-ROM X 1

Rubber footer X 1

10

4. Introduction 4.1 Panel

4.1.1 Front Panel Standard form factor model (production is suspend)

Small form factor model

4.1.2 Rear Panel Standard form factor model (production is suspend)

There is a button on the rear panel of this server for special maintenance. Please don’t push this button under normal operation.

Small form factor model


11

4.2 LED indicator Label Description

PWR ON Power supply is normal

ALRAM (ALM)

ON Errors detected when auto HW diagnostics running

ON Able to access to TIME SERVER

Flash The system tries to access TIME SERVER every 30 minutes. If Time Server is not reachable, the LED is flashing until the system is able to access Time Server

TIME SRVR

OFF System has not yet access to Time Server.

ON All SIP Entity of this MOSA SIP Line is registered to other Proxy Server successfully. When Server Mode is configured, this LED keeps ON

Flash Only partial SIP Entity of this MOSA SIP Line is registered to other Proxy Server successfully.

Registered (REG)

OFF All SIP Entity of this MOSA SIP Line is registered to other Proxy Server failed

ON System is connected to VODNET

Flash Both NETMOSA and NETMOSA Plus are configured, but only one server is registered. NETMOSA

OFF Not registered to NETMOSA

ON The system is linked to STUN Server STUN

OFF System never communicates with STUN Server.

ON Transmission Rate is 100Mbps 100Mbps (Small model has LED only) OFF Transmission Rate is 10Mbps

ON Network Linked Up

FLASH Sending/Receiving data packets Link/ACT (Small model has LED only)

OFF Network connection is fail

12

4.3 Connector Connector Label Description

To WAN (MDI-X) (For

standard model only) RJ-45 MDI-X connector, connect to WAN (Wide area network)

To LAN (MDI) (For

standard model only) RJ-45 MDI connector, connect to LAN

RJ-45

1, 2, 3, 4, 5 (For small

model only) Auto MDI and MDI-X for connection to LAN

RJ-45 CONSOLE Connect to system console


13

5. Basic Configuration 5.1 Console Configuration After connect the PC with this server via RS-232 Console cable, power on the PC and configure the PC parameters as following:

Speed: 9600

Data Bits: 8

Parity Check: None

Stop Bit: 1

Flow Control: None

If Console cable is not available, run Telnet in PC for connection is OK.

14

6. Configuration of Functions 6.1 General configuration

(1) Connect the Console Terminal to MOSA 4600B SIP Line Console port by RS-232<-->RJ-45 cable.

(2) Configure the parameter of Console Terminal. Please refer to Section 5.1 Console Configuration.

(3) Enter a fixed IP address for System Console (or use the default IP address 192.168.0.2)，Apply warm-start to restart the system. Please refer to 6.1.1 Configuration of IP.

(4) Connect PC to the network port labeled “To WAN” by LAN cable. The Indicator of LNK/ACT will be ON if the connection is working normally.

(5) Set IP address of PC to the same section as IP address of this bridge. For example, the default IP address of this bridge is 192.168.0.2, and then you may set 192.168.0.3 as the IP address of PC. (Re-start PC may be required).

(6) Start IE browser and input the IP address of this machine, and then press Enter.

(7) The window for USER ID and PASSWORD will be prompted. Enter “WEB” (all capital letter) as USER ID and the password. If password is not configured, keep it blank, press ENTER key. Now you are on the Home page of the Web Management page.

(8) On the Web Management Page, set the Country Code, Area Code, Phone Number, NETMOSA IP Address, UDP port and other features. Please refer to Section 6.2.1 Configure My Phone Number。

(9) If you like to use DHCP services, you may set the parameters via Web Management Page or via Console terminal and restart the system. Please be attention, new dynamic IP address will be applied after restarting. It causes the problem to enter the original Web Management Page. You have to check the new IP address via Console terminal and enter the Web Management page with this new IP address.

(10) When all setting is finished, connect the machine to Internet. The system will be in operation after the indicator of TIME SRVR turns ON.

6.1.1 Configuration of IP An IP Address is required for MOSA 4600B SIP Line series product. How to get the IP address depends on the network environment for which the FONEMOSA 4484 will be connected. Please refer to the following table and the network configuration to define the IP address information you need before system configuration. If fixed IP address will be used, you have to apply your Internet Service Provider (ISP) to get an available IP address. It is not recommended for DHCP IP. In the following table, please find the information required under different network configuration.


15

IP Network Configuration Information Required Public IP address IP address

Subnet mask Default Gateway Notes: Usually the IP address is assigned by ISP to avoid the conflict with the other equipments.

Fixed IP Address

Private IP address IP address Subnet mask Default Gateway Notes: An IP Sharing device is required for private IP address. In the IP Sharing device, IP address of this bridge has to be set as a virtual Server

DHCP Please contact your MIS people. It is not recommended

You may perform the IP setting via System Console or Telnet, and then enter the Web Management page to perform the other settings.

Configuration of IP Address via System Console

Configuration via System Console: or by Telnet, Start Run Telnet 192.168.0.2 in Windows

(In this example, we use fixed IP IP will be 10.13.6.21 Subnet mask is 255.255.255.0 Default Gateway is10.13.6.130)

SIP Line (12) >enable SIP Line (12) #configure Enter configuration commands, one per line. End with CNTL/Z SIP Line (12) (config)#ip state user SIP Line (12) (config)#ip address 10.13.6.21 255.255.255.0 System needs to restart SIP Line (12) (config)#ip default-gateway 10.13.6.130 SIP Line (12) (config)#exit SIP Line (12) #restart This command resets the system. System will restart operation code agent. Reset system, [Y]es or [N]o? Yes

16

Modify IP Configuration via Web Management Page.

Web folder: IP SETTING

6.2 Basic parameter configuration Please start browser and input the IP address previous set for this machine. Press Enter to show the window below. Please input the account name as “WEB” (must be in capitals) and the password, blank or previous set for the web. Press the OK button to enter the home page.


17

Basic parameter is the setting to run the basic function of this machine. Basic parameter includes: Item

Description

Country Code Country Code, such as 1 (USA)

Area Code Area Code of Telecom area, e.g. 2 for Taipei Notes: Area Code 2 for Taipei; 7 for Kaohsiung; 21 for Shanghai; 10 for Beijing

Phone Number Phone Number of FONEMOSA 4484, e.g. 82261111. You can make an IP call via another FONEMOSA by dialing this number.

IP address of Netmosa or Netmosa+

If your VoIP environment use Netmosa or Netmosa+, You need to setup the IP address of Netmosa or Netmosa+

Port of Netmosa or Netmosa+

If your VoIP environment use Netmosa or Netmosa+, You need to setup the Port number of Netmosa or Netmosa+

6.2.1 Configure My Phone Number Country Code, Area Code and Phone Number can be configured at Web Folder: Basic\System Config

Select Region ID of your country and click Modify button to take effect. (Don't Change if your country is not listed in the options)

Web Folder：Basic\System Config

Configure the phone number of this machine. Number can be the same as company PSTN number. If you keep the Phone Number field blank and the machine is connected to Internet, then system input VODNET number automatically.

Please Warm-Restart the machine when configuration is done.


18

System Restart -> Warm Restart -> Click Apply

6.2.2 Registration of NETMOSA and/or NETMOSA Plus For this series of product, system is joined to NETMOSA group automatically if the Serial number of NETMOSA or NETMOSA Plus (Also called NETMOSA +) are defined. Joins NETMOSA+ can make VODNET call easily.

Refer the following figure of “NETMOSA IP Setting”, which is part of page IP Setting. Configuration is done when product is shipped. You can contact with distributor if data is missed.

Please Warm-Restart the system when the setting is done. Web Folder：IP Setting

6.2.2.1 View the registered NETMOSA and/or NETMOSA+ ID via web After successfully setting the Serial Number of NETMOSA and NETMOSA + in this machine, then go to the page BASIC to check if system is successfully joined in NETMOSA. Input NETMOSA ID and press Register button if necessary. The phone number will be displayed as the following figure that is part of page BASIC.

You can also check the LED at front panel to know the registration status of NETMOSA or NETMOSA+



19

6.3 Basic Structure

6.3.1 Client Mode

Note：Application Service Devices including NETMOSA，Forwarding Server，CDR Server，Parking Server，ACD Server...and so on.

MOSA 3704B

Soft Phone SIP IP Phone

SIP Gateway

SIP Proxy Server

SIP Device

SIP Network

MOSA 4600B SIP Line Server

MOSA 4600

Application

Service Device

VODNET Network

FONEMOSA 4400 Plus

Internet PSTN

T1/E1

Trunking Gateway

Virtual FXS

Virtual FXS

20

6.3.2 Server Mode

Soft Phone SIP IP Phone

MOSA 3704B

SIP Gateway SIP Device

SIP Network

MOSA 4600

VODNET Network

FONEMOSA 4400 Plus

Internet PSTN

Application Service Device

T1/E1Trunking Gateway

MOSA 4600B SIP Line

Virtual FXS

Virtual FXS


21

7. Configuration and Operation of Server Mode

7.1 What is Server Mode Server Mode means MOSA 4600B SIP Line act as SIP Proxy itself. SIP devices that do not have SIP Proxy to register to, can register to MOSA 4600B SIP Line Server directly. No needs to buy expensive SIP Proxy.

The related configuration for MOSA 4600B SIP Line Server to be a Proxy Server

♦ Configure IP address

♦ Enable this machine as SIP Registrar (Proxy)

♦ Configure related setting of Registrar Server

♦ Configure STUN Server, DID related setting

♦ Input authentication information to this machine individually for other SIP device that will register to this machine. (open account)

♦ Create Prefix Map (extension number)

7.2 Configuration of Server Mode

7.2.1 Use STUN Server Note: Don't use STUN Server is suggested. Firmware 1.06.2 or above does not have this Web page.

Configuration of STUN Server

To make MOSA 4600B SIP Line to working smoothly under NAT device, STUN Server can be used in this case, however, STUN Server may be controled by others or there is no STUN Server at all. So don't use STUN Server might be suggested. If you use STUN Server, NAT WAN IP is provided by STUN Server, so please configure NAT WAN IP of MOSA 4600B to 0.0.0.0 (Disable)

To configure STUN Server, please refer to

Web Folder：Advanced-SIP\STUN

22

Structure:

7.2.2 Configure NAT WAN IP and Disable STUN Server NAT WAN IP needs to configure according to different environment and STUN Server has to be disabled.

Note: Firmware 1.06.2 or above has built-in Media Relay function and configuration of NAT WAN IP is not required and system does not has such Web page.

Web Folder：Advanced-SIP\STUN

7.2.2.1 Environment 1: User inside compnay only (LAN) Configure NAT WAN IP to 0.0.0.0, because SIP devices have not to penerate NAT device to Internet.


IP of this machine

WAN IP mode of this machine

Network side of SIP devices

Input NAT WAN IP Note

Private None LAN 0.0.0.0 (default) Don’t change

NAT Device (IPSharing Device

SIP Line

MOSA 3700

Internet WAN

LAN

SIP Phone

NAT WAN IP: 0.0.0.0 (Disable)

NAT Device (IP Sharing DeviceSIP Line

Internet LAN

STUN Server


SIP Phone

Configure Server Port to map SIP Line (behind NAT)

SIP Line (behind NAT)

SIP Phone


23

Web Folder: Advanced-SIP / STUN, default value is 0.0.0.0

7.2.2.2 Environment 2: User in Internet and 4600B use Public Static IP MOSA 4600B SIP Line is installed with Internet connection and NAT WAN IP is not required. Configure it to 0.0.0.0


IP of this machine




Public Static WAN 0.0.0.0 (default) Don’t change

Web Folder: Advanced-SIP / STUN, Default Value is 0.0.0.0

7.2.2.3 Environment 3: User in LAN or Internet, and 4600B use Private Static IP of NAT with Fixed Public IP

MOSA 4600B that is installed behind NAT has to know the IP address that NAT device connect to Internet. So the NAT WAN IP address needs to configure to the fixed public IP address that ISP provides. Open Server Port: 5060/2000/10000~10719 of NAT device to map SIP Line inside NAT device (For the procedure to configure Server Port, please refer to

NAT Device (IP Sharing Device

SIP Line

Internet WAN

LAN


SIP Phone

SIP Phone

MOSA 3700

Fixed Public IP

24


IP of this machine




Private Static LAN + WAN WAN IP

Web Folder: Advanced-SIP / STUN

7.2.2.4 Environment 4: User in LAN or Internet, and 4600B use Private Static IP of NAT with Dynamic Public IP

Open Server Port: 5060/2000/10000~10719 of NAT device to map SIP Line inside NAT device (For the procedure to configure Server Port, please refer to

By this way, work with Router that supports DDNS (Dynamic DNS, please refer to Router's user manual) or VDNS Server (this service depends on your distributor, please contact distributor) is suggested, otherwise, when dynamic IP is changed, SIP phone (Softphone) is unable to register MOSA 4600B, unless configure new IP address for SIP Phone (Softphone)

♦ For DDNS Router (NAT device), it can supports dynamic IP change for DNS. Please refer to its manual and also apply Dynamic DNS Service.

♦ For VDNS Server, Softphone or MOSA 3700 can configure its DNS IP address to the IP address of VDNS Server. VDNS server helps Softphone or MOSA 3700 to find the IP address of MOSA 4600B SIP Line or the IP address of NAT device that MOSA 4600B use.

For the configuration of Softphone and MOSA 3700, please refer to 7.3 How to register for Client



InternetWAN

LAN

NAT WAN IP: (Fix Public IP that ISP Provides

SIP Phone

Configure Server Port to map SIP Line

SIP Line (behind NAT) MOSA 3700

SIP Phone


25

IP of this machine




Private Dynamic LAN + WAN 255.255.255.255 Work with DDNS or VDNS is

recommended.

Web Folder：Advanced-SIP / STUN

7.2.3 Configuration of one step dialing DID mode ♦ Configuration of DID mode

SIP device can make one step dialing call to VODNET or other SIP phone by DID mode. In real application, please make sure that two steps dialing is OK before applying DID mode.

MOSA 3700, SIP Phone, Softphone is like the extension of VODNET. All digits dialed after hook off the extension, is sent to MOSA SIP Line. MOSA SIP Line receives the digits and dial out the number the same as the number which extension dial.

When SIP device make one step dialing to MOSA 4600B SIP Line, MOSA 4600B SIP Line will analyze the number that SIP device dial and create the route to VODNET directly. When this mode is enabled, all digits dialed from SIP device is transferred to MOSA 4600B SIP Line

Configuration:

1. Enable the DID (Direct Inward Dial) mode. The first few digits transferred from SIP Proxy can be deducted. For example, incoming call is 12345671021 and Prefix Length is configured to 7, then 1021 is dialed for two-steps dialing. How many digits can be deducted can be configured at web page. The digits left is dialed from MOSA 4600B SIP Line to device of VODNET or SIP. Please Enable this function and configure Prefix Length to 0

Web Folder：Advanced-SIP\Common (Default values and change is not required)

InternetWAN

NAT WAN IP: 255.255.255.255

MOSA 3700

Dynamic Public IP


LAN SIP Phone SIP Line

(behind NAT)

SIP Phone

Configure Server Port to map SIP Line

26

7.2.4 Other Necessary Configuration Please make sure to configure the other setting in this section.

7.2.4.1 Configure IP Address Please refer to 6.1 General configuration

7.2.4.2 Disable Outbound Proxy and Registrar When MOSA 4600B SIP Line acts as server itself, it is not necessary to register other SIP Proxy. The Outbound Proxy and Registrar function used at Client side need to disable, because Server Mode needs not those function

(Note: In order not to confuse Serve Mode and Client Mode, Firmware 1.06.2 or above is divided into Server Mode and Client Mode. For Server Mode version, there is no such setting and system also does not show it).


7.2.4.3 Enable this machine as SIP Registrar Web Folder：Advanced-SIP\Registrar (Default values and change is not required)

7.2.4.4 Activate NAT Traversal function Show the function as the figure below


27

For some NAT device, it disconnects the connection of IP device (SIP Phone, MOSA 3700) if they fail to send any packet in a period of time. When these device send packet again via NAT device again, the mapping port No. is changed and it causes the connection fail. If NAT Traversal function is activated, MOSA 4600B SIP Line send packet every 50 seconds to where the packet come from and it can make sure the port mapping inside and outside NAT device intact.

This function helps the SIP Phone or SIP Gateway (MOSA 3700) that use Private IP behind NAT and there are no STUN server supported, to penetrate NAT to register MOSA 4600B SIP Line. When SIP phone or SIP gateway react the packet sent from MOSA 4600B SIP Line, it keeps the IP/Port mapping intact inside and outside NAT. It keeps the connection alive.

ON：Send Option Packet every 50 seconds to where the packet come from. OFF：Don't send Option Packet to where the packet come from. Default: ON。

Web Folder：Advanced-SIP\Registrar (Default values and change is not required)

7.2.4.5 Configure Expires Time When the SIP devices that register to this machine expires the duration configure here without registering again, this machine disconnect the connection automatically.

Web Folder：Advanced-SIP\Registrar (Default values and change is not required)

7.2.4.6 Create SIP Entity, configure Public Address and enable Caller ID authentication.

For the reason that SIP device is able to make call to MOSA 4600B SIP Line, MOSA 4600B SIP Line need to create SIP Entity number for SIP device to make call. Unlike Client Mode, when MOSA 4600B SIP Line acts as client, SIP Entity number is specified by other SIP Proxy and you can not change it as you want. However, acting as Server Mode, Entity number can be specified by yourself.

(Note: In order not to confuse Serve Mode and Client Mode, Firmware 1.06.2 or above is divided into Server Mode and Client Mode. For Server Mode version, there is no such setting (default is OK) and system also does not show it).


SIP Line MOSA 3700

Internet LAN

Send Option Packet every 50 second

SIP Phone STUN Server React packet to keep IP/Port mapping intact

28


Public Address of MOSA 4600B SIP Line should be "machine contact name"@"machine IP", for example: [email protected]

Change of Default Value 1234501~1234590 (elder version: 1234567) is not required. SIP client can make call between extension without make call to SIP Entity of this machine first. This Entity number is two steps dialing for some SIP Phone that can not make direct call directly.

7.2.4.7 Configure Extension No. of SIP device Channel for SIP device need authentication by Caller ID and Caller ID need to configure at virtual channel

Web Folder：Channel\Configuration

Select Channel

SIP extension number is the number that configure in SIP URI field. When Caller ID is enabled, SIP device has to use the same account name in order to make call to this channel. It can be digits or characters, such as 889900 or Lester1021. There are pre-configured accounts Ext10~Ext99 at each port (default value of small form model) and use default value is OK.


29

7.3 How to register for Client When configuration of Server Mode at MOSA 4600B SIP Line is done. Clients also need to do some configuration in order to register MOSA 4600B SIP Line. Client can be SIP Phone, SIP Softphone, SIP gateway…and so on.

7.3.1 Configure MOSA 3700 as Client ♦ Configure DNS (Please ignore this section if client register to MOSA 4600B by IP address)

If the SIP Proxy Server uses Domain Name for the registration of client, such as SIP.vodtel.com.tw (including Domain Name of DDNS or VDNS), then client has to specify the IP Address of DNS Server. The DNS Server can resolve the IP address that MOSA 4600B use or the IP address of the NAT device that MOSA 4600B use. Use the DNS IP address that ISP provided is suggested. These DNS Server can resolve domain name, such as www.yahoo.com

For example, configure Primary Address of DNS Server as: 139.175.55.244

MOSA 3700 Web Folder：ADVANCED\IP SETTING

♦ Configure IP address, Subnet and Default Gateway of MOSA 3700 and connect it to IP network. For detail, please refer to user manual of MOSA 3700.

♦ Configure Outbound Proxy and Registrar

Input the IP address of MOSA 4600B SIP Line (such as 10.13.6.21) or Domain Name (such as SIP.vodtel.com.tw)

Web Folder of MOSA 3700：ADVANCED\SIP COMMON

♦ Configure SIP Entity and Public Address


Configure an Entity and use 889900 as account (SIP number). This number is the SIP number of MOSA 3700 for MOSA 4600B SIP Line. There are pre-configured account Ext10~Ext99 at each port (default value of small form model) and use default value Ext10~Ext99 to do registration is OK. Try to make a successful call first.

30

Restart the system to take effect the configuration.

♦ Check registration status from MOSA 3700

Check MOSA 3700 to see if it registers to MOSA 4600B SIP Line successfully.


♦ Check registration status from MOSA 4600B SIP Line

Registration of each SIP device can be checked at MOSA 4600B SIP Line. It includes the registration status of MOSA 3700.

Web Folder of MOSA 4600B SIP Line：Advanced-SIP\Registrar

7.3.2 Configure Other SIP Device as Client VODTEL list some most used models and describe its configuration and operation in detail. Please refer to several documents that are released by VODTEL: Quick Installation and


31

operation for XX SIP Phone to register MOSA4600B SIP LINE (XX presents Brand and Model name)

Please go to VICA Zone Web of VODTEL to download. Permission control is applied on the web and only the distributor of VODTEL can download it.

http://61.222.217.2/disty/modules/mydownloads/singlefile.php?cid=92&lid=408 (Chinese)

http://61.222.217.2/disty/modules/mydownloads/singlefile.php?cid=92&lid=410 (English)

We illustrate the example by TTN's Softphone. The software can be downloaded from http://www.gogotalk.net.tw/ (If the address is changed, please find it in the related field inside the web)

Please refer to the description of that web page for how to install the software. Here we just tell you what parameters need to be modified according to the example of this chapter.

♦ Configure DNS IP Address of PC (Please ignore this section if client register to MOSA 4600B by IP address)

Depending on your network structure, configure DNS IP Address of PC as "Obtain DNS server address automatically" or " Use the following DNS server addrsses" (fixed DNS IP address and also input IP address of DNS). Make sure that the DNS IP address or the DNS IP got automatically can resolve the IP address that MOSA 4600B use or the IP address of the NAT device that MOSA 4600B use.

Notes: For Windows 2000, XP and 2003, 2 (or more) sets of DNS can be inputted. For Windows 95, 98 and ME, only one sets of DNS is acceptable.

32

♦ Input IP address or Server name of MOSA 4600B SIP Line and the port number it uses.

Input IP: 10.13.6.21 at Proxy Server1 and Out-bound Proxy 1 field. If you have two MOSA 4600B SIP Line, you can input the IP address of 2nd MOSA 4600B SIP Line at Proxy Server2 field. Use default Port Number 5060. If MOSA 4600B SIP Line does not use 5060, please configure it to the same number as MOSA 4600B SIP Line.

For Softphne that use DDNS or VDNS, input Domain Name of MOSA 4600B in Proxy Server1 and Out-bound Proxy 1, such as SIP.vodtel.com.tw. As for the Domain Name, it depends on the DDNS service the you applied or setting on VDNS Server (please contact distributor)

♦ Input 889900 to My Number and User ID field

It is easier to manage the system if My Number and User ID are configured the same. Please input the same number 889900 that is configured in MOSA 4600B Web Folder: Channel\Configuration, SIP URI field in Virtual Device. (There are pre-configured account Ext10~Ext99 at each port (default value of small form model) and use default value Ext10~Ext99 to do registration is OK.)

♦ Check Registration Status

Close the software and restart the software. The registration status become Registered from Registering. Means the registration is successful.


33

♦ Check registration status from MOSA 4600B SIP Line

Registration of each SIP device can be checked at MOSA 4600B SIP Line. It includes the registration status of Softphone.

Web Folder of MOSA 4600B SIP Line：Advanced-SIP\Registrar

7.4 The Application of Server Mode MOSA 4600B SIP Line acts SIP Proxy itself. SIP Phone, SIP Softphone and SIP gateway can register to MOSA 4600B SIP Line directly to have conversation with VODNET and to use the service of VODNET Application Figure

MOSA/FONEMOSA (MOSA 4600) machine is installed in company for the extensions of

MOSA SIP Line

MOSA 4600 MOSA 3700

VODNET SIP

81-3-3665100 (VODNET)1234567 (SIP Entity 1) 1011 886-2-82263368

Channel 1 map to SIP Entity 1(Ext. 10)

SIP Phone (Notebook)

1010

34

colleagues. Or connect MOSA 4600 to PBX of company. Sales that usually go abroad or out of office can take Notebook PC that had already install SIP Softphone and it is registered to MOSA 4600B SIP Line. Sales can make phone call to the extension of company from anywhere if network is available and no extra phone bill occur.

If sale is out off office but his notebook is on-line with him, user of extension of company can make extension call to the notebook of sale.

7.4.1 SIP Extension Map (for Server and Client mode) MOSA 4600B can be configured for many dialing behavior and access code. For easy configuration, the system is pre-configured many default value. If you use default value, the system has the extension number below for making calls. See the explanation.


Channel:

Extension Number: Channel Number

Extension Number = 10+ Channel Number

It has Prefix Extension No. 10, because default value has a set of Prefix Number (default value: 10) and its Phone No. is the number of MOSA 4600B itself (Full Number, shown in Web Folder: BASIC\System Config, My Phone Number field, default value is VODNET No. if this machine is connected to Internet), then dialing between SIP extensions is possible.

Web Folder：Advanced-MOSA\Prefix Map

Then it has the Channel Number mapping table as below. Extension No. is the real number you dial.


35

Channel Number mapping table

Channel Ext. Ext. Channel Ext. Ext. Channel Ext. Ext.

Channel No. No. Acc.

ChannelNo. No. Acc.

ChannelNo. No. Acc.

1 10 1010 Ext10 31 40 1040 Ext40 61 70 1070 Ext70

2 11 1011 Ext11 32 41 1041 Ext41 62 71 1071 Ext71

3 12 1012 Ext12 33 42 1042 Ext42 63 72 1072 Ext72

4 13 1013 Ext13 34 43 1043 Ext43 64 73 1073 Ext73

5 14 1014 Ext14 35 44 1044 Ext44 65 74 1074 Ext74

6 15 1015 Ext15 36 45 1045 Ext45 66 75 1075 Ext75

7 16 1016 Ext16 37 46 1046 Ext46 67 76 1076 Ext76

8 17 1017 Ext17 38 47 1047 Ext47 68 77 1077 Ext77

9 18 1018 Ext18 39 48 1048 Ext48 69 78 1078 Ext78

10 19 1019 Ext19 40 49 1049 Ext49 70 79 1079 Ext79

11 20 1020 Ext20 41 50 1050 Ext50 71 80 1080 Ext80

12 21 1021 Ext21 42 51 1051 Ext51 72 81 1081 Ext81

13 22 1022 Ext22 43 52 1052 Ext52 73 82 1082 Ext82

14 23 1023 Ext23 44 53 1053 Ext53 74 83 1083 Ext83

15 24 1024 Ext24 45 54 1054 Ext54 75 84 1084 Ext84

16 25 1025 Ext25 46 55 1055 Ext55 76 85 1085 Ext85

17 26 1026 Ext26 47 56 1056 Ext56 77 86 1086 Ext86

18 27 1027 Ext27 48 57 1057 Ext57 78 87 1087 Ext87

19 28 1028 Ext28 49 58 1058 Ext58 79 88 1088 Ext88

20 29 1029 Ext29 50 59 1059 Ext59 80 89 1089 Ext89

21 30 1030 Ext30 51 60 1060 Ext60 81 90 1090 Ext90

22 31 1031 Ext31 52 61 1061 Ext61 82 91 1091 Ext91

23 32 1032 Ext32 53 62 1062 Ext62 83 92 1092 Ext92

24 33 1033 Ext33 54 63 1063 Ext63 84 93 1093 Ext93

25 34 1034 Ext34 55 64 1064 Ext64 85 94 1094 Ext94

26 35 1035 Ext35 56 65 1065 Ext65 86 95 1095 Ext95

27 36 1036 Ext36 57 66 1066 Ext66 87 96 1086 Ext86

28 37 1037 Ext37 58 67 1067 Ext67 88 97 1097 Ext97

29 38 1038 Ext38 59 68 1068 Ext68 89 98 1098 Ext98

30 39 1039 Ext39 60 69 1069 Ext69 90 99 1099 Ext99

36

7.4.2 Dialing Method ♦ From SIP to VODNET

Two Steps Dialing

User of SIP Phone (Softphone) dials 1234567 (SIP number of MOSA 4600B. For Firmware 1.06.2 or above, default is 1234501~1234590 that maps Entity 1 ~ Entity 90) and hear the dial tone from MOSA 4600B SIP Line, and then user can dial call to VODNET or SIP Extension. The behavior is the same as making call in VODNET

Example：

1. **002-8862-82263368-11# (Complete No. dialing, 002 is international access code, 886-2-82263368-11 is country code + area code + Machine No. + extension No.)

2. **200-6666-11# (IP Call dialing method，by VODNET No.＋extension No.)

3. *7-200-6666-11# (VODNET dialing method，by VODNET No.＋extension No.)

4. 88 (Prefix dialing，Prefix need to configure in advance. For Prefix Number, please refer to...)

Note: Some Softphone softwaremay not support two steps dialing after the connection is built. Only DID mode with one step dialing is available.

One Step Dialing

If DID mode is enabled, and the Prefix Length of DID is 0, one step dialing is OK

Example：

1. **002-8862-82263368# (Complete No. dialing)

2. **200-6666-11# (IP Call dialing method，by VODNET No.＋extension No.)

3. *7-200-6666-11# (VODNET dialing method，by VODNET No.＋extension No.)

4. 88 (Prefix dialing，Prefix need to configure in advance)

♦ From VODNET to SIP

VODNET user dial "# + number of MOSA 4600B SIP Line + Channel number" to connect SIP Phone. Extension number is configured to connect SIP device.

Example：

1. #002-81-3-3665100-10# (Complete No. dialing, 002 is international access code, 81-3-3665100-10 is country code + area code + number of MOSA SIP Line＋Channel number)

2. 8801 (Prefix dialing，Prefix is configured: 8801= 81-3-3665100-10，connect Channel 1 of MOSA 4600B SIP Line)

♦ From SIP to SIP (Dialing between two extension)

Two Step Dialing


37

User of SIP Phone (Softphone) dials 1234567 (SIP number of MOSA 4600B. For Firmware 1.06.2 or above, default is 1234501~1234590 that maps Entity 1 ~ Entity 90) and hear the dial tone from MOSA 4600B SIP Line, and then user can dial call to other SIP device

Example：

1. Then dial 1011 to other SIP device (SIP device that register to Channel 1 of MOSA 4600B SIP Line. Dialing by Prefix Number. Prefix No. 10 has to be configured as MOSA 4600B its own number (My Phone Number), 11 is Channel number)

Note: Some Softphone software may not support two steps dialing after the connection is built. Only DID mode with one step dialing is available.

One Step Dialing

If DID mode is enabled, and the Prefix Length of DID is 0, one step dialing is OK

Example：

1. Dial 1011 to other SIP device (SIP device that register to Channel 1 of MOSA 4600B SIP Line. Dialing by Prefix Number. Prefix No. 10 has to be configured as MOSA 4600B its own number (My Phone Number), 11 is Channelnumber)

7.5 Use Video Call SIP client device can make video call via this machine. In addition to voice, user also can see each other.

We use eyeBeam SIP Phone as example. The information of this software can be seen at

http://www.xten.com/

Software can be installed in PC. If SIP Video Phone is used, then PC is required. For the SIP client devices model that can use video phone, please contact with distributor.

For the detail configuration and usage of eyebeam, please refer to eyeBeam user manual that can be downloaded at

http://www.xten.com/docs/eyeBeam1.11UserGuide.pdf

7.5.1 Configuration of MOSA 4600B Please refer from Section 7.1 to 7.2 to finish the configuration of MOSA 4600B and make it is ready for eyebeam to do registration

To avoid free registration of SIP Client, configure SIP inbound authentication to control the permission. For this registration, please refer to 9.1 SIP Inbound authentication (for Client and Server mode)

Specify Realm and it can be customized by yourself

Web Folder：Advanced-SIP\Inbount Auth

38

Specify the Username and Password of SIP inbound authentication

This example use Entity 1, Username: 1020 (or Ext19), Password: 1234

Web Folder：Advanced-SIP\Inbount Auth

Note: Username: 1020 (or Ext19)has to be the same as SIP URI (in this example, we use Channel 10 and factory default value SIP URI 1020 or Ext19 is pre-configured). For this kind of authentication, please refer to 9.2 Caller ID authentication (for Server Mode only)


Create another account information in MOSA 4600B

To make calls, at least two accounts are required.

For example: Username: 1021 (or Ext20). Password: 2234.

Enable specified channel that is able to use Video call

Enable Video Control option at that channel.


Select Codec for Video call and the priority of these codecs

Codec that is not selected will not used in priority sequence. For eyeBeam, adjustment is not required.

7.5.2 Configuration of SIP Client Device Install eyeBeam

Run eyeBeam installation program. Skip detection of MIC and Earphone first. System shows the


39

screen below and configures it according to procedure below:

Enter Account Information Get a set of SIP account, Password and IP address of Proxy Server from system administrator. In this example, we use SIP Account【1020】, Password【1234】, Proxy Server IP【192.168.46.89】 and Control port of Proxy Server is【5060】

SStteepp 11： Enter

【eyeBeam】

Software

SStteepp 22： Click【Right mouse

button】Click

【Settings…】field.

SStteepp 66： Click【Register with domain】and

【Use as Outbound Proxy】

SStteepp 44： EyeBeam can register to several accounts at the same time. When【Enable this SIP account】is ticked, means the account is enabled

SStteepp 55： ♦ Input【1020】in Display Name. It is the

name shown at Server ♦ Input【1020】in User name. It is the

account from admin ♦ Input【1234】in Password. It is the

password from admin ♦ Input【1020】in Authorization user

name. It should be the same as User name

♦ Input 【Domain name or IP】and【portnumber】of MOSA 4600 Plus

SStteepp 77： Click【Apply】

SStteepp 33： Click【Server】

40

Setting of Environment：

Confirm the registration status to MOSA 4600 Plus:

SStteepp 22：

Tick【Enable acoustic

echo cancellation】。

SStteepp 33：

Tick【Enable VAD】。

SStteepp 11：

Clcik【Headset】tab


41

Configure video setting

Configure the setting of Video at the setting page.

Before the configuration below, install the PC Camera in advance, including the installation of driver. Please refer to the user manual of PC Camera

Configure Codec

No Codec adjustment is required if you use eyeBeam. If you use other brand of SIP Phone, please adjust it if required.

SStteepp 11：

Slect【General】in video

tab

SStteepp 22：

Select PC cam you want

to use

SStteepp 33：

Select the specification

of video.

SStteepp 44：

Click OK

42

Use the same eyeBeam at another PC and configure it according to steps above to register MOSA 4600B

When the procedure above is done, you should be able to make calls. Generally speaking, if audio driver is installed successfully on the PC, MIC and Earphone should be OK to use. If you are not sure, verify it with eyeBeam. Here is the method. Follow the procedures of system. If you don't have USB Phone, test Headset only is OK.

7.5.3 Make Video call To make video call, you should make normal voice call first. Start to transmit video later when voice conversation starts.


43

1. User (A) of 1020 dial 1021, 1021 is ringing. User (B) of 1021 answers the call.

A presses 1020 + , 1021 is ringing. B presses to answer the call. Conversation starts.

2. A and B click Video tab and Start to transmit Video.

3. Video is started. They can see each other.

A sees B sees

4. Click to close conversation

44

8. SIP Network Configuration (Client Mode)

When this machine is configured as Client Mode, it means both MOSA 4600B SIP Line and other SIP device are all register to the same other SIP Proxy Server.

Configuration procedure:

1. Select a Channel and join it to specified SIP Entity.

2. Configure data for SIP Proxy and Register server

3. Select the priority of Codec Type

4. Configure the phone number of SIP Entity.

5. Setup the certification data of SIP outbound call. This function is available only if the SIP Service Provider provides this service.

6. Configure data to connect STUN Server. Configure the data only if this gateway uses virtual IP (behind NAT)

7. Verify the SIP registration status.

8.1 System Configuration

8.1.1 Select Channel and SIP Entity Web Folder：CHANNEL\CONFIGURATION

Restart is required when configuration is done.

Select the channels that need to configure and join it to SIP Entity.


45

8.1.2 Configure SIP Proxy and Registrar Server Web Folder：Advance-SIP\Common

Outbound Proxy will redirect the SIP call to correct route and Registrar Server is for SIP phone number registration. Please ask this information from SIP Service Provider.

8.1.3 Select Codec Type and Priority WEB Folder：Advanced-SIP\Common

Select different kinds of Codec Type to communicate with other SIP gateway. Different kinds of Codec Type mean different kinds of voice compress standard. Codec Type that is not selected will not communicate with other machine.

You can select different kind of Codec Priority. Selected Codec Type can have different priority. Codec Type with higher priority will communicate with other machine first. If the highest priority codec is not supported on the other machine, the system will try the second priority Codec Type.

Note: There are 5 fix Codec Type in Codec Priority, however, the Codec type that is not selected will be ignored. (PCMU means G.711 u Law, PCMA means G.711 A Law)

For the example below: The selected Codec Type are G.729AB，G.723.1，PCMA and the Priority are G.723.1，G.729AB，PCMA

46

8.1.4 Configure SIP Number SIP Service Provider provides you the SIP phone number. Input this number to the field of Public Address Setting.

The Format of general SIP number looks like E-Mail Address, for example: [email protected]

Web Folder: Advanced-SIP \ Common

Select the SIP Entity you want to configure, enable it and input the SIP number. After input the related data, click Apply and Warm-Restart the machine.

Hint: All ports can share the same one SIP account (number) to register to the same SIP Proxy. Each port use individual SIP account (number) to register to the same SIP Proxy is also OK. However, each port to register to different SIP Proxy server is not possible.

8.1.5 SIP Outbound Authentication If the SIP number needs to be verified by SIP Service Provider, please input the data here. If the information of Default Account is configured at last section, system creates default Outbound Authentication automatically.

Note: There is no such Web page at Firmware 1.06.2 or above. Use default value is OK.

Web Folder: Advanced-SIP \ Outbound Auth

Select the Entity that you want to configure and input the data of Realm (generally, the same as

Show "Registered" if successful


47

Proxy Server), and then input Username and Password. Click Apply button to take effect these setting. If the related Realm information is not inputted, this machine will use default value to replace it and list it at top of web page.

8.1.6 Configure STUN Server setting or WAN IP When MOSA 4600B is connected behind NAT or Firewall Router and use virtual IP Address, please activate this function and configure the setting of STUN Server. If Proxy Server supports NAT traversal function, STUN Server is required. Please ask the information from SIP Service Provider.

Configure to use the support of STUN server is not a good configuration. For Firmware 1.06.2 or above, it is removed. Please configure NAT WAN IP instead.

We Folder: Advanced-SIP\WAN IP. For the configuration of NAT WAN IP, it is the same as Server Mode. Please refer to 7.2.2 Configure NAT WAN IP and Disable STUN Server

Elder version: Web Folder: Advanced-SIP\STUN

48

8.1.7 Check the registration status of SIP entity Check Web Folder：Advanced-SIP\Common

If the field shows “REGISTERED”, the machine is registered successfully. If other words are shown, the registration is not successful.

If it is not successful, please check to see if all settings are correct. Please contact SIP Service Provider for problem.

8.1.8 Contact Address The main function is to dial a phone call to other machine directly without passing through the Proxy. Machine at two sides need to use fix IP.

Web Folder：Advanced-SIP\Common


49

For some Proxy, the Contact Address Setting needs to be the same as Public Address below. So please configure it the same to prevent any failure connection occur if it route to Proxy.

For example, if Public Address is [email protected], then configure Contact Address to 414911

Configuration:

For example, the SIP Entity 1 of MOSA 4600B SIP Line needs not receive incoming call via Proxy. The IP address of this machine is 210.62.111.12 and the No. of SIP Entity 1 you want to configure is 234.

Then you can input 234 in Contact Address Setting of Entity 1

MOSA 4600B SIP Line Web folder：Advanced-SIP\Common

The SIP device that need to make call to MOSA 4600B SIP Line has to configure Contact Name as 234 and IP Address as 210.62.111.12 in Phone Book.

The dialing method of SIP device (use MOSA 3700 as example) that make call to MOSA 4600B SIP Line:

Pick up SIP device and then dial #234# to reach MOSA 4600B SIP Line, and then you can dial to VODNET.

8.1.9 SIP Call Forward It provides the function that the incoming SIP call can be forward to specified SIP Number. When SIP device 414910 make call to 414911, the call is forward to 414912, owing to the call forward function from Entity 1: 414911 to Entity 2: 414912 is configured on MOSA 4600B SIP Line

Note: To simplify installation, this function is removed for Firmware 1.06.2 or above, owing to rare use in practical case.

Forward Address has to be complete SIP address, such as 414912@fwd,pulver.com

Type of SIP Call Forward

None：Disable call forward

All：All incoming call is forwarded

Busy：Incoming call is forwarded to specified SIP number when line is busy

No Answer：No answer the call till 30 seconds, the call is forwarded to specified SIP number.

SIP Line Entity 1: 414911 MOSA 3700

VODNET SIP

SIP Phone 414910

414912

50


8.2 From VODNET to SIP Concept: Via MOSA SIP Line, MOSA 4600 at VODNET side can consider SIP device (such as MOSA 3700) in SIP environment as extensions. User of MOSA 4600 is able to dial the extension of MOSA SIP Line to talk with user of SIP device.

User at MOSA 4600 side dial 002-81-3-3665100-17# (002 is international access code), then the call route is built to SIP device 73796 directly. That SIP device rings. Configure Prefix 81-3-3665100-17 as 8816 at MOSA 4600 side, then SIP device 73796 rings when MOSA 4600 side dial 8816.

Configuration:

MOSA 4600 side (for detail, please refer to MOSA 4600 user manual)：

1. Configure IP address, My Phone Number: 886-2-82263368 and register it to NETMOSA+.

2. Create Phonebook Entry. Number 81-3-3665100 to point to MOSA 4600B SIP Line

3. Create Prefix number to simplify dialing. For example, create prefix number 8816 = 81-3-3665100-17

MOSA 4600B SIP Line：

1. Configure IP address. My Phone Number: 81-3-3665100 and register to NETMOSA+

2. Configure SIP Entity (such as Entity 1). For example, the number which SIP ISP provides: 73797 and register to SIP Proxy successfully. For the other configuration about SIP, they are all located at Web Folder:\Advanced-SIP. For detail, please refer to chapter 8 SIP Network Configuration (Client Mode) and Sections of Web Folder: Advanced-SIP\ of this manual.

3. For example, map Channel 8 to a SIP Entity number.

Web Folder: Channel\Configuration

Select Channel 8 and click Select button, and Extension Number will show 17 automatically.

SIP Line

MOSA 4600 MOSA 3700

VODNET SIP

81-3-3665100 (VODNET)73797 (SIP Entity 1)

73796 886-2-82263368

Channel 8 maps to SIP Entity 1(Ext. 17)

SIP Proxy (fwd.pulver.com)


51

Configure SIP number for channel. Incoming call from VODNET to this Channel will route to SIP phone directly. For example: [email protected] (73796 is SIP number, fwd.pulver.com is the location of SIP Proxy)


SIP devices (MOSA 3700)：

♦ Please refer to its user manual and configure it to register fwd.pulver.com by account 73797 that other SIP device can make call 73796 to reach this SIP device

Dialing Method

♦ User at FXS port of MOSA 4600 dials

8816, then this call route to 73796 in SIP environment

♦ Transit-in call from PSTN to SIP

Dial 82263368 from PSTN and Auto Attendant answer the call. Then dial 8816, this call route to 73796 in SIP environment.

♦ Extension 8815 of MOSA 4600 FXS port is configured "Forward To" to 81-3-3665100-17 No matter the call is dial from PSTN and then dial extension number or it is dialed from other extension to 8815. This call is forwarded and then this call route to 73796 in SIP environment

8.3 From SIP to VODNET Figure：Example of connection is shown below, can dial from SIP to VODNET

8.3.1 Two Step Dialing Concept: After SIP device (such as MOSA 3700) in SIP environment dial to MOSA SIP Line, it looks the same as any extension in VODNET picks up handset. Then user can dial to other device in VODNET by any dialing behavior of MOSA 4600 series.

As the example above, SIP device 73795 dials to SIP Line server will hear second dial tone. By dialing behavior of VODNET, user can use all phone call service of VODNET

Configuration:

SIP Line

MOSA 4600 MOSA 3700

VODNET SIP


73796 886-2-82263368

Channel 8, 9 maps to SIP Entity 1

SIP Proxy

SIP Device

73795

52


1. Configure IP address, My Phone Number: 886-2-82263368 and register it to NETMOSA+. It makes other MOSA machine and MOSA 4600B SIP Line are able to make call to this MOSA 4600.

MOSA 4600B SIP Line side：

1. Configure IP. My Phone Number: 81-3-3665100 and register to NETMOSA+


3. Configure Channel 8, 9 two (or more) channel. There are 2 (or more) SIP phone that can dial to 73797 at the same time


Select Channel 8 and click Select button. Extension Number will show 17 automatically.

Join this Channel to SIP Entity 1


Then select Channel 9 and repeat previous two steps.

4. Configure Prefix and it makes SIP phone is able to do one step or two steps dialing to VODNET. For example: Prefix 88 = 886-2-82263368-11

Web Folder: Advanced-MOSA\Prefix


♦ Please configure it according to its user manual and make it able to dial SIP call to 73797


53

Dialing Method

♦ If SIP user dial 73797 only, he/she will hear second dial tone. (MOSA 4600B SIP Line seize free channel, such as Channel 8. If there is second incoming 73797 SIP call, system will seize Channel 9.) Then user can dial VODNET number, such as 88.

8.3.2 One step dialing DID Mode Concept: MOSA 3700 (SIP device) can act as an extension of VODNET, any digits dialed after

pick up handset will be transferred to MOSA SIP Line. The dialing behavior of MOSA SIP Line after it receives the digit, is the same as pick up extension and dial number. (Using this function, SIP Proxy for registration of SIP device must support DID mode)

As the example figure above, make one step dialing from SIP Device 73795 to SIP Line Server. SIP Line server can analyze the number that SIP device 73795 dials and create route to VODNET side directly.

Configuration:

Channel 8, 9 of MOSA 4600B SIP Line all joins to SIP Entity 1. SIP user dial Prefix and call route is built to the extension of MOSA 4600 (MOSA 4600B SIP Line had create Prefix to point to the extension of MOSA 4600), and then that extension rings.

The configuration is the same as two steps dialing and only need to configure more on DID mode.

1. Please contact with SIP ISP to enable and configure the DID mode of SIP Proxy. When this mode is enabled, all digits that SIP device dial is transferred to MOSA 4600B SIP Line.

2. Configure Prefix Length of DID mode. The first few digits transferred from SIP Proxy can be deducted. How many digits will be deducted can be configured at Web page. The digits left will dial from MOSA 4600B SIP Line to VODNET

Web Folder：Advanced\SIP

Dialing Method

♦ SIP Proxy had applied DID mode and configure it that all number which SIP device dial are all transferred to MOSA 4600 SIP Line, then MOSA 4600B SIP Line use Prefix Length 5 (see configuration below). SIP user dial 7379788 (Configure Prefix 88 = 886-2-82263368-11 at MOSA 4600B SIP Line in advance. 886-2-82263368 is the full number of MOSA 4600), then call route is built to extension 11 of MOSA 4600. Extension 11 rings.

Configure DID Prefix Length at Web Folder：Advanced\SIP

54

8.4 From VODNET to Different SIP Concept: Many MOSA 4600B SIP Line can connect to the same VODNET environment to create call route to different SIP environment. By this way, Machine extension in VODNET can consider SIP phone in different SIP ISP as extension. No matter where SIP phone user is located, if SIP phone is connected to IP network, user in VODNET can dial extension number to SIP Phone.

Configuration:



2. Create Phonebook Entry. Number 81-3-3665100 to point to SIP Line Server (1), 81-3-3665200 to point to SIP Line Server (2)

3. Create Prefix number to simplify dialing. For example, create prefix number 8816 = 81-3-3665100-17, Prefix：8818 = 81-3-3665200-17

MOSA 4600B SIP Line Server side：

1. Configure IP. My Phone Number of SIP Line Server (1): 81-3-3665100, My Phone Number of SIP Line Server (2): 81-3-3665200 and register to NETMOSA+

2. Configure SIP Entity (such as Entity 1). For example, the number which SIP ISP provides: SIP Line Server (1)：73797, SIP Line Server (2)：66132. and register to SIP Proxy successfully. For the other configuration about SIP, they are all located at Web Folder:\Advanced-SIP. For detail, please refer to chapter 8 SIP Network Configuration (Client Mode) and Sections of Web Folder: Advanced-SIP\ of this manual.

3. Map Channel 8 to SIP Entity


Select Channel 8 and click Select button. Extension Number will show 17 automatically.

MOSA 4600

VODNET

886-2-82263368

SIP Line Server(1)

SIP


73796

Channel 8 maps to SIP Entity 1


SIP Device

SIP Line Server(2)

SIP


66133

Channel 8 maps to SIP Entity 1

SIP Proxy (61.222.217.80)

SIP Device


55

Configure SIP number for channel. Incoming call from VODNET to this Channel will route to SIP phone directly. For example: SIP Line Server (1)：[email protected] (73796 is SIP number, fwd.pulver.com is the location of SIP Proxy) and SIP Line Server (2)：[email protected] (66133 is SIP number, 61.222.217.80 is the IP address of SIP Proxy)


SIP Line Server (1)

SIP Line Server (2)


1. Please refer to its user manual and configure it that other SIP device can make call 73796 (from SIP user using fwd.pulver.com SIP proxy), 66133 (from SIP user using 61.222.217.80 SIP proxy) to reach these SIP device

Dialing Method

1. User at FXS port of MOSA 4600

Dials 8816, then this call route to 73796 in SIP environment (by using fwd.pulver.com SIP proxy). Dials 8818, then this call route to 66133 in SIP environment (by using 61.222.217.80 SIP proxy)

2. Transit-in call from PSTN to SIP

Dial 82263368 from PSTN and Auto Attendant answer the call. Then dial 8816 or 8818 to user of different SIP environment.

3. Extension 8815 of MOSA 4600 FXS port is configured "Forward To" to 8816

No matter the call is dial from PSTN and then dial extension number or it is dialed from other extension to 8815. This call is forwarded to 8816 and then this call route to 73796 in SIP environment. The same rule can be applied to different SIP environment.

8.5 Incoming Call from Different SIP Environment Concept: Many MOSA 4600B SIP Line can connect to the same VODNET environment to create call route to different SIP environment. By this way, SIP user in different SIP ISP can make call to VODNET and consider Machine in VODNET as extension, or make Outbound call to PSTN. No matter where SIP phone user is located, if SIP phone is connected to IP network, SIP user can make call to the extension of VODNET.

56

Configuration:

Please refer to section 8.3 From SIP to VODNET, and configure two MOSA 4600B SIP Line

Dialing Method

Both SIP Line Server (1) and SIP Line Server (2) can use the same Prefix No, then no matter where the SIP user dial from, the extension number which users dial is the same.

For detail, please refer to 8.3 From SIP to VODNET.

8.6 Penetrate Different SIP Environment Concept: A MOSA 4600B SIP Line and a MOSA 4600C SIP Trunk can connect to the same VODNET environment to build call route for different SIP environment. SIP users in different environment can talk to each other directly via the support of MOSA 4600B SIP Line and MOSA 4600C SIP Trunk. SIP user just make two steps dialing to reach other SIP user at different SIP environment.

MOSA 4600

VODNET

886-2-82263368

SIP Line Server (1)

SIP


73796



SIP Device

73795

SIP Line Server (2)

SIP


66133


SIP Proxy (61.222.217.80)

SIP Device

66131

SIP Device

SIP Device


57

8.6.1 From MOSA 4600B SIP Line to MOSA 4600C SIP Trunk

Configuration:

MOSA 4600B SIP Line side (For detail, please refer to related sections of this manual)：


2. Create Phonebook entry, number 81-3-3665200 and point to MOSA 4600C SIP Trunk


MOSA 4600C SIP Trunk side (For detail, please refer to MOSA 4600C SIP Trunk user manual)：

1. Configure IP address, My Phone Number: 81-3-3665200, and register it to NETMOSA+.

2. Configure SIP Entity (such as Entity 1). For example, the number which SIP ISP provides: 66132 and register to SIP Proxy successfully. For the other configuration about SIP, they are all located at Web Folder: ADVANCED\SIP COMMON. For detail, please refer to MOSA 4600C SIP Trunk user manual.

3. Configure Outbound Transit for MOSA 4600B SIP Line to make outbound call to SIP via this MOSA 4600C SIP Trunk.

Configuration Procedure：

MOSA 4600C SIP Trunk Web Folder：BASIC\OUTBOUND TRANSIT

1) Input MAC address and Phone Number of MOSA 4600B SIP Line

2) Open Trunk Call Allowed function and Click Apply

MOSA 4600

VODNET

886-2-82263368

SIP Line ServerSIP

81-3-3665100 (VODNET)73797 (SIP Entity 1) Create Prefix: 7816 to 81-3-3665200

73796



SIP Device 73795

SIP Trunk ServerSIP

81-3-3665200 (VODNET)66132 (SIP Entity 1) Create Prefix: 9816 to 81-3-3665100

66133

SIP Proxy (61.222.217.80)

SIP Device

66131

SIP Device

SIP Device

58

Calling side SIP device (MOSA 3700)：

1. Please refer to its user manual and make this SIP device (No. 73796 or 73795) is able to make call to 73797

Dialing Method

♦ SIP device (number 73796 or 73795) of fwd.pulver.com Proxy dial 73797 and hear second dial tone, and then dial #66133## (Country Code 81, Area Code 3 is the same, no need to dial) to reach 66133 SIP device of other SIP environment (SIP Proxy: 61.222.217.80), or

♦ SIP device (number 73796 or 73795) of fwd.pulver.com Proxy dial 73797 and hear second dial tone, and then dial *9-81-3# (assume *9 is the Access Code of Seize Remote Trunk and it can be configured at ADVANCED\NUMBERING PLAN. 81 is Country Code, 3 is Area Code) to seize dial tone of MOSA SIP Trunk (SIP environment by SIP Proxy: 61.222.217.80), then dial 66133 to make call.

8.6.2 From MOSA 4600C SIP Trunk to MOSA 4600B SIP Line Please refer to connection figure above 8.6.1


59

From MOSA 4600B SIP Line to MOSA 4600C SIP Trunk

Configuration:

MOSA 4600C SIP Trunk side (Please refer to related chapter of that manual)： 1. Configure IP address, My Phone Number: 81-3-3665200 and register it to NETMOSA+. 2. Configure SIP Entity (such as Entity 1). For example, the number which SIP ISP provides:

66132 and register to SIP Proxy successfully. For the other configuration about SIP, they are all located at Web Folder: ADVANCED\SIP COMMON. For detail, please refer to MOSA 4600C SIP Trunk user manual.

3. Create Phonebook entry, number 81-3-3665100 to point to SIP Line Server. 4. Create Prefix to simplify dialing. For example, create Prefix: 9816 to point to 81-3-3665100

MOSA 4600B SIP Line side (For detail, please refer to related section of this manual)：



3. Map Channel to SIP Entity. Configure Channel 8 (Extension 17) to SIP Entity number 73796. Please refer to 8.2 From VODNET to SIP.

Calling side SIP device (MOSA 3700)： 2. Please refer to its user manual and make this SIP device (No. 66133 or 66131) is able to

make call to 66132

Dialing Method

1. SIP device (number 66133 or 66131) of 61.222.217.80 Proxy dial 66132 and hear second dial tone, and then dial #PIN code#9816-17# to reach 73796 SIP device of other SIP environment (SIP Proxy: fwd.pulver.com). For the configuration of PIN code, please refer to user manual of MOSA SIP Trunk.

60

9. SIP Authentication for Incoming Call For security reason, the incoming SIP calls may have to pass the authentication (can be disable) for VODNET call. The authentication is described below.

9.1 SIP Inbound authentication (for Client and Server mode)

Note: To simplify configuration, Firmware 1.06.2 or above does not provide this kinds of authentication in Client mode, owing to rare use in practical case. Generally speaking, Client does not request authentication from other side. Mis-configure the setting cause connection fail.

By this authentication, input information of Realm, Username, and Password in Web Folder: Advanced-SIP\Inbound Auth of MOSA 4600B SIP Line. When SIP device make call to MOSA 4600B SIP Line, MOSA 4600B SIP Line request authentication from SIP device. SIP device send information of Realm, Username, Password for authentication. If authentication is OK, dial tone is heard and make VODNET call is available. If authentication is fail, busy tone is heard.

By this authentication, it has to input Realm, Username and Password in SIP device (such as MOSA 3700, Softphone)

For the example below: Input Realm, Username and Password into MOSA 4600B SIP Line

Web Folder of MOSA 4600B SIP Line: Advanced-SIP\Inbound Auth

Input Realm: vodtel, select such as Entity 2, Username: 3400, Password: 3375 (Note: all incoming call can use the same Entity, such as Entity 1. For Username, we suggest you to use default extension number, such as 1011~1099. For extension number, please refer to ...

Attention: For Firmware 1.05 or above, if you activate this authentication, Username of SIP Inbound authentication must be consistent with the SIP URI. In other words, SIP URI number is also used as Username of SIP Inbound authentication. For the description of SIP URI, please refer to next section.


61

If other SIP device such as MOSA 3700 or SIP phone that dial Public Address of Entity 2 has to pass the authentication of MOSA 4600B SIP Line, then the same information, Realm: vodtel, Username: 3400, Password: 3375 has to be entered in the Outbound Authentication of MOSA 3700 (SIP client device)

The Web Folder of MOSA 3700：Advanced-SIP\Outbound Auth

When this user of MOSA 3700 make call to MOSA 4600B SIP Line Entity 2, it provides the same authentication data of MOSA 4600B SIP Line SIP Entity 2, then user hear dial tone and he/she can dial VODNET number or SIP Extension next. When other MOSA 3700 or SIP Phone that have different Realm, Username, Password makes call to MOSA 4600B SIP Line, busy tone is heard.

Please refer to 11.9 Advanced-SIP\Inbound Auth for the method of configuration

9.2 Caller ID authentication (for Server Mode only) Note: To simplify configuration, Firmware 1.06.2 or above does not provide this kinds of authentication, owing to rare use in practical case. Generally speaking, Caller ID is the same as the Username of SIP Inbound authentication, so use SIP Inbound authentication is OK.

By this authentication, SIP device (such as MOSA 3700, Softphone) has to send Caller ID spontaneous. Generally speaking, Caller ID is SIP number (SIP Entity number) and it is provided by SIP Proxy (MOSA 4600B SIP Line) owner and it is configured in SIP URI in Virtual Device field. MOSA 4600B SIP Line can verify the Caller ID sent from SIP device.

For this authentication, function can be Enabled or Disabled for each SIP Entity. Use SIP Entity 1 as example. Select SIP Entity 1 first.


Then, activate Caller ID function of that Entity.


MOSA 4600B SIP Line can join different Channel into the same SIP Entity. So configures the

62

Channels that need Caller ID authentication to join Entity, such as Entity 1.



And then, input Caller ID for authentication in individual Channel. For the example below, use 412260, then the caller ID authentication for that channel is 412260 and the channel join SIP Entity 1 of this machine. System had been pre-configured 1010~1099 number (SIP URI) for authentication and you can use it without change.

Attention: For Firmware 1.05 or above, if you activate this authentication, SIP URI (Caller ID) must be consistent with the Username of SIP Inbound authentication. In other words, SIP URI number is also used as Username of SIP Inbound authentication. For the description of SIP Inbound authentication, please refer to previous section.


After above configuration, the incoming call to that Channel must come from SIP phone 412260 (Caller ID). If Caller ID of the incoming call is not 412260, then busy tone is heard, because only 412260 can make call to this Channel.

9.3 PIN code authentication (for Server Mode only) Note: To simplify configuration, Firmware 1.06.2 or above does not provide this kinds of authentication in Client mode, owing to rare use in practical case. Mis-configure the setting cause connection fail.

By this authentication, user of SIP device has to dial extra PIN Code+# for authentication after he/she make call to MOSA 4600B SIP Line. If authentication is successful, second dial tone is heard. If PIN Code dialed is not correct or no PIN Code dialed, busy tone is heard.

For this authentication, function can be Enabled or Disabled for each SIP Entity. Use SIP Entity 1 as example. Select SIP Entity 1 first.



63

Then, activate PIN Code authentication of that Entity.


And then, input PIN Code for individual Entity. The same Entity can have many PIN Code for authentication. For the example below, Entity 1 have two PIN Code, 3746 and 3321.

Web Folder：Advanced-SIP\PIN Code

After the configuration above, SIP device that intent to make call to SIP Entity 1 can make call to MOSA 4600B SIP Line and then dial

PIN Code + # + the No. of MOSA machine + # or

PIN Code + # + Prefix No.

PIN Code + # + SIP 分機號碼

Since two steps dialing is applied, so make sure to disable DID mode in advance



65

10. VODNET Network Configuration If your MOSA 4600B apply to the calls between SIP devices only, you can skip this chapter.

If the MOSA IP-PBX (used in VODNET and it connects to your desktop phoneset) communicates with SIP device via this MOSA 4600B, you can configure it according to this chapter.

10.1 Numbering Plan The numbering plan for this product is to define the access code for each kind of services and the

manner of dialing. These codes will be applied often, therefore the code should be simple, easy to

remember, and unique. The prefix of equipment should be put into consideration to prevent the

conflict. For the prefix of equipment, please refer to 10.2 Prefix Map.

The access code consists any combination of 0 ~ 9, * , and # ; and The first character can not be 0. If an access code is defined, you can define another access code by this code followed

by one extra character, only one character is allowed. For example, “*2” is defined as Abbr. Dial Access Code, then “*21” or “*22” may be defined as another access code.

Code can not be used if that has been defined as a prefix in Prefix Map Table. Also pay attention to the combination of Access Code + Dialing Plan. For example: Dial

(*2) + Index (00) can not be the same as other Access Code

The correct defined access codes are listed for your reference:

Use the access code as the example below simplify the configuration and it match the example described in this manual. However, for different environment, the factory default value may not exactly the same as the table below.

Item Access Code

IP Calls Only

IP Calls **

Trunk Group 1 Access 9

Phoneset Programming *0

Abbr. Dial *2

Call Pick Up *7

Call Pick Up with Extension *4

Netmosa Plus Call *3

Seize Remote Trunk *9

Seize Specific Trunk (Class) *8

66

Call Retrieve *1

10.1.1 Frequently Used Dialing Example In a similar environment as below and MOSA 4600B is configured as Server Mode, a series of dialing behavior can be achieved by configuration of Dialing Plan and other setting.

♦ Dialing between extensions

1011, 1012, 2011, 2012 dialing extension number directly

Example：User of extension 1011 dial 2012. Extension 2012 rings

♦ Call Pick-Up

If all devices are configured on the same Subnet, extension 1011, 1012, 2011, 2012 can pick up each other’s extensions.

Example：Press *7 to pick up other ringing extension.

♦ Seize trunk

Extension 1011, 1012, 2011, 2012 is able to seize trunk and make PSTN call

Example：Dial 9 and hear second dial tone, and then dial PSTN number

♦ Incoming call from PSTN

Dial extension 1011, 1012, 2011, 2012 to reach different extension for PSTN incoming call.

Example：For incoming PSTN call, Auto Attendant answer the call, and then calling side dials 1011. Softphone extension 1011 rings

♦ Dial VODNET No.

Extension 1011, 1012, 2011, 2012 dial VODNET number.

Example：Dial *3 + VODNET number

MOSA SIP LineVODNET

SIP

PSTN

SIP Phone 1012

Soft Phone 1011

MOSA 4600

2011 2012

FONEMOSA 4496


67

10.1.2 Exception Dialing Example Because the SIP phone or Soft Phone is bridged by MOSA SIP Line to VODNET, the dialing method may change for some special code, such as *, #, and Flash. The explanation is shown as below.

♦ Send DTMF after the route is built

For the call dial from SIP to VODNET, when the route to VODNET is created and user has to send DTMF by phone again.

Button on phone set Action Real DTMF sent

0~9 Dial 0~9 0~9

* Dial * *

## Dial # twice #

# Owing to different SIP devices, some may not send # when dial #. Try to dial ## to replace

Any digits+#. If the duration between this # and previous digits is shorter then 4 second. This # is consider as DTMF #. If it is larger then 4 second, this # is consider as Flash

Dial # (Flash) and then dial "Trunk Access Code", such as 9

Transmit Flash at remote FXO port

Transmit Flash at remote FXO port

♦ Call transfer

User in VODNET side please press Flash + Extension No.

Example：Incoming call to extension 2011, user of 2011 press Flash+1012 and then the call is transfer to 1012, 1012 rings.

User in SIP side please dial # + Extension No.

Example：Incoming call to extension 1011, user of 1011 press #+2011 and then the call is transfer to 2011, 2011 rings.

♦ 4 sides conference call

When FONEMOSA 4496 (PBX Conference Bridge) is used and chairman invite others to join conference.

Chairman in VODNET side press Flash + Prefix Number of FONEMOSA 4496 (such as 4496) + #

Example: Flash+4496+#

Chairman in SIP side press # + Prefix Number of FONEMOSA 4496 (such as 4496)

Example: # + 4496

68

When Chairman needs to invite more people to join the conference

Chairman in VODNET side press # and hear confirmation tone. Hook on in 3 seconds (chairman had leave conference) and hook off again. And then invite other by dialing other's number

Chairman in SIP side press * * and hear confirmation tone. Hook on in 3 seconds (chairman had leave conference) and hook off again. And then invite other by dialing other's number

(Note: For Firmware 1.06 or above, the Prefix type to FONEMOSA 4496 can be configured as Conf, then hook oo phoneset is not required.

Different SIP Phones may have different kinds of dialing behavior. VODTEL list some most used models and describe its configuration and operation in detail. Please refer to several documents that are released by VODTEL: Quick Installation and operation for XX SIP Phone to register MOSA4600B SIP LINE (XX presents Brand and Model name)

10.2 Prefix Map For this machine, you can define a prefix number for each MOSA\FONEMOSA of the machine itself in the Prefix Map Table. Then you can connect to the equipment by dialing the prefix number defined for that equipment. It look like extension number when user make call. When other MOSA/FONEMOSA make calls to this machine, the system converts original Caller ID to prefix number according to Prefix Map. It is easier to identify and to call back.

There are three fields in the Prefix Map Table:

1. Prefix number

The prefix ID for other equipment, maximum length is 6 characters.

2. Phone Number

The phone number of MOSA\FONEMOSA series or MOSA 4600B SIP Line itself. The NETMOSA / NETMOSA +ID may be entered in this field. It is the mapping of Prefix number to the equipment. Version Firmare 1.05 or above allows to use "x" to represent the phone number of the machine itself. (For example: x = phone number itself, x11= phone-number-itself+11). By this way, once user change the Country Code, Area Code or My Phone Number of the machine itself, the related "x" in Prefix Map keeps consistent with the changed new phone number.

3. Type : There are iPBX, Phone and Conf

iPBX is selected for MOSA 4600 series or FONEMOSA 4400/4400 Plus series Phone is selected for others MOSA 4500 or FONEMOSA 4200.

If iPBX is defined in Type, system will start to create the call path after dialing prefix number plus 2 digits extension number (prefix number + Ext No), or prefix number plus “0” (prefix number + 0). Actually, the corresponding telephone number of other equipment defined in the Prefix Map Table is sent out. In the later case, “0” will be treated as the access code for Operator if Operator is defined in the system, otherwise the “0” after the Prefix number will be ignored.


69

If Phone is defined in Type, system will start to create the call route after dialing the Prefix number.

If Conf is defined in Type, it is suitable to connect with FONEMOSA 4496

10.2.1.1 Restrictions in Prefix Map Table Prefix Map Table is part of Numbering Plan, any confliction and duplication are not allowed. Please take care some restrictions. Avoid from defining the prefix number starting with digit “0”. In the definition of tradition

telephone numbering plan, “0” is defined as the starting digit for accessing long distance call or international oversea call.

The maximum length of Prefix code is 6 characters. In principle, you can’t define a new prefix number starting with the number that has been defined previously. For example, “33” is defined as a prefix number, then any numbers starting with “33”, like “330”, “3312”, can not be defined as a prefix number. Of course, “31”, “32”, or “34” are OK. Another example, “555” is defined previously, then “5551” or “55522” can not be defined as a prefix number, but “551” or “552” or “553” …etc. is OK.

Attention: When MOSA 4600B is configured as Server Mode (acts as SIP Proxy itself), it has to configure a set of Prefix Number (default value: 10) and its Phone No. is the number of MOSA 4600B itself (Full Number, shown in Web Folder: BASIC\System Config, My Phone Number field, default is VODNET number if the machine is conneced to Internet), then dialing between SIP extensions is possible.

Firmware 1.05 or above has a pre-configured Prefix No. 10 in Prefix Map and user can skip this step

10.3 VODNET Call Forward The feature of Call Forward is to predefine a destination on the channel, then all calls to this channel will be forwarded to the destination automatically.

Calls from VODNET to SIP device can be forward to destination in VODNET as below.

The extension line of another MOSA 4600 Plus, MOSA 4600 or FONEMOSA 4400 series at remote side

The FXS port of another FONEMOSA 4200/4300 at remote side

The FXS port of another MOSA 4500 at remote side through NETMOSA

The public line (PSTN) through the machine at remote side (Off-net Forward)

Calls from SIP to MOSA 4600B SIP Line can be forward to destination in SIP environment as below.

The FXS port of another SIP device in the same SIP environment at remote side, such as MOSA 3700. (For call forward of SIP device, please refer to 8.1.9 SIP Call Forward)

70

10.3.1 Forward to VODNET MOSA 4600(1) makes call to MOSA SIP Line 81-3-3665100 (Dial 8801, MOSA 4600(1) use Prefix No., configure 8801=81-3-3665100-10, and this call will reach Channel 1 of MOSA SIP Line: Extension 10. Channel 1 of MOSA SIP Line is configured Call Forward to 886-2-82263391), and then this call is Forwarded to 886-2-82263391.

There are 3 parameter needs to configure for calls to VODNET：

Parameter Description Control Forward-Disable : Disable Forward Feature

Forward-All Calls : Forward all calls Forward-Busy : Forward only if this line is busy Forward-Busy-Slave : Forward only if this line is busy. And if the forwarded line is also busy and Forward-Busy-Slave is defined, this call will be forwarded to next destination as configured. NoAnswer-Forward: When there is no answer for this line, the call forward to the specified destination Busy/NoAnswer-Forward: When there is no answer or line busy for this channel, the call forward to the specified destination

Forward To Phone number of the remote equipment (such as MOSA 4600) or NETMOSA/NETMOSA+ ID that will be forwarded to. The phone number must be a full number including country code and area code. For example: 886282263391(886 is the country code of Taiwan, 2 is area code and 82263391 is the machine number). If Offnet To is configured to PSTN, the call will offnet to PSTN by the machine configured here.

Offnet to The telephone number of PSTN or mobile phone that the call will be forwarded to. The telephone number is entered from the viewpoint of transfer machine (the remote equipment that the phone number had entered in the field of “Forward To”). For example, the local machine is located in Shanghai. The MOSA that will forward your call is located at Taipei, phone No. 82263391 and you want to make a PSTN mobile phone call to Taipei No. 0930911556, so you configured 0930911556 as "Offnet to" No. here.


MOSA SIP Line

VODNET SIP

81-3-3665100 886-2-82263368

MOSA 4600(1)

MOSA 4600(2) 886-2-82263391


71

For normal Forward To FXS channel of remote MOSA 4600, it only needs to configure Control and Forward to parameter. If outbound call to PSTN from remote MOSA 4600 is required, then it also needs to configure Offnet To parameter.

Attention: Please make sure that the IP call (FXS to FXS) between the two parties is OK before configuring Call Forward function. To make a successful IP call, you can configure Phone book or join VODNET and dial VODNET number

10.3.2 Configuration of remote MOSA 4600 If the call is forwarded from local MOSA 4600B SIP Line to the FXS channel of remote MOSA 4600, no configuration is required on remote MOSA 4600.

If the call has to offnet forward to PSTN via remote MOSA 4600, then it needs to configure the No. to PSTN on Permitted Phone Number for Offnet Forward page at remote MOSA 4600 Configuration of remote MOSA 4600，Web Folder：BASIC\OFFNET FORWARD (If remote site is MOSA 4600 Plus, Web Folder: 1.System Config.\1.7.Offnet Forward)

Note: The number configured at Offnet To is the real number dial to PSTN. In this case, we wants it offnet to PSTN mobile phone, so we configure it to mobile phone only. Complete number is not required.

Example

72

This machine, MOSA 4600B SIP Line is located at Shanghai. Forward To machine is located at Taipei 886-2-82263391. The extension that will offnet net to PSTN mobile phone 0930911556 in Taipei：

Parameter MOSA 4600B SIP Line Local side

(At Shanghai)

Remote MOSA 4600

(886-2-82263391) (At Taipei)

Control Enable -

Forward to： 886282263391 -

Offnet to： 0930911556 -

Permitted Phone Number for Offnet forward - 0930911556

10.4 SIP Seize Remote Trunk at VODNET side

Dialing Method: SIP device make call to MOSA 4600B SIP Line and hear second dial tone, and then dial <#>+<Seize Remote Trunk Access Code> + <Country Code> + <Area code>+<#> or PIN Code+<#>+<Seize Remote Trunk Access Code> + <Country Code> + <Area code>+<#> For example:

IP ShanghaiSIP Line

FXS

FXO

MOSA 4600

CO

… Dial PIN# *9 8621#

Country Code: 86

Area Code: 21

SIP Network


73

There is one MOSA 4600 in Shanghai (8621). At Shanghai side, MOSA 4600 is configured as giving the permission for Taipei to place the Outbound Transit Call. The Trunk Call Allowed is set to TRUE for Country Code= 86 and Area Code=21. At Taipei side, Seize Remote Trunk Access Code is configured as “ *9 “. Under such configuration, Taipei can place a call to Shanghai PSTN line through the MOSA 4600 in Shanghai, and also can seize the remote trunk of MOSA 4600 in Shanghai by dialing “ *9 8621# “.

Configuration of Local MOSA SIP Line： Define the Access Code of Seize Remote Trunk, from Web Management Page, folder：Advanced-MOSA \ Numbering Plan

Configuration on the Remote Side：

Allow remote MOSA 4600 (MOSA/FONEMOSA machine) to give the permission for MOSA 4600B SIP Line to make Outbound Transit Call. Input MAC address, Phone Number of MOSA 4600B SIP Line and the Route type through this MOSA 4600, and set Trunk Call Allowed to TRUE and set the field Allow Remote Access of Trunk Group to TRUE

Remote MOSA 4600 Web Folder：BASIC\OUTBOUND TRANSIT (If remote site is MOSA 4600 Plus, Web Folder: 1.System Config.\1.5.Outbound Permission)

Web Folder：Advanced \ Trunk Group (No configuration is required if remote site is MOSA 4600 Plus)

74

10.5 Abbreviated Dial The feature of Abbreviated Dial is to provide a simple and short dialing behavior to send out the complex and long telephone number instead of dialing the full telephone number. There are 100 entries for Abbreviated Dial. The Abbreviated Dial Index is for SIP device to make call to MOSA SIP Line and hear second dial tone and then dial

< Abbr. Dial Access code > + <Abbr. Dial Index (00 ~ 99) >

Web Folder: Basic\ABBR Dial

0 ~ 9 , * , and # may be used to define the Abbr. Dial Index in Abbr. Dial Table. The number defined in the table is the actual digits to be dialed out for making a phone call. For example, if you would like to dial “ 9 “ then the call of telephone number “ 0921888666 ” will be made, and then you should configure the telephone number in the Abbr. Dial Table as “ 90921888666 “. Another example, if you would like to make an IP call **82263368#, then you can configure the telephone number as “ **82263368# “ in Abbr. Dial. Please configure Abbr. Dial Access Code in advance, please refer to 11.2 Basic\ABBR. Dial

10.6 Softkey The function of Softkey can be configured on each channel. The Trigger mode of Softkey may be defined. The Softkey may consists digits 0 ~ 9 , * , and # . Combine with the function of Softkey and Abbr. Dial you may have varied applications.

For configuration, please refer to：11.14 Channel\Configuration

I. Example 1 : Hot Line

User’s Activities : User off-hooks the phone, number “ #0921555666# “ is sent out automatically.


75

Configuration :

Field Value Entered Soft key String #0921555666# Trigger Mode Auto Trigger Digits Blank Append Trigger Digits Not Append

Example 1：(Hot Line) User’s behavior : Make call from SIP device to MOSA SIP Line, then MOSA SIP Line make call to #0921555666# automatically.

Configuration：

Field Value Entered

Soft key String #0921555666# Trigger Mode Auto Trigger Digits Blank Append Trigger Digits Not Append

10.7 Abbr. Dial Combined with Softkey Combine Abbr. Dial and Softkey can have varied and convenient application. Example 1：

Activities of User’s expectation：

User off-hooks the phone and dial “ 0 “ , system will send out “#00286135556666# “

User off-hooks the phone and dial “ 1 “ , system will send out “#0921666888# “

User off-hooks the phone and dial “ * “ , system will send out “#6688# “

User off-hooks the phone and dial “ # “ , system will send out “#668812# “

Configuration：

Abbr. Dial Access Code : Web Management Page folder “ADVANCED”, select “NUNMBERING PLAN” page

Field Value Entered

Abbr. Dial Access Code 5

Abbr. Dial Configuration : Web Management Page folder “BASIC”, select “ABBR. DIAL” page

76

Field Value Entered Index 10 #00286135556666# Index 11 #0921666888# Index 20 #6688# Index 21 #668812#

Softkey : Web Management Page folder “CHANNEL”, select “CONFIGURATION” page

Field Value Entered Soft key String 51 Trigger Mode Key Press Trigger Digits 1234567890*# Append Trigger Digits Append

Explanation of how system works：

User dials “ 0 “ , Softkey is triggered and “ 510 “ is sent out. This number meets the definition of Abbr. Dial Access Code “ 5 “ , followed by Abbr. Dial Index “ 10 “, therefore the actual number dialed out is #00286135556666#

User dials “ 1 “ , Softkey is triggered and “ 511 “ is sent out. This number meets the definition of Abbr. Dial Access Code “ 5 “ , followed by Abbr. Dial Index “ 11 “, therefore the actual number dialed out is #0921666888#

User dials “ * “ , Softkey is triggered and system converts “ * “ to “ 10” , therefore “ 520 “ is sent out (Please refer the figure below). This number meets the definition of Abbr. Dial Access Code “ 5 “ , followed by Abbr. Dial Index “ 20 “, therefore the actual number dialed out is #6688#

User dials “ # “ , Softkey is triggered and system converts “ # “ to “ 11” , therefore “ 521 “ is sent out (Please refer the figure below). This number meets the definition of Abbr. Dial Access Code “ 5 “ , followed by Abbr. Dial Index “ 21 “, therefore the actual number dialed out is #668812#

10.8 MOSA Phone Book If the IP address of a frequently used remote FONEMOSA/MOSA is a Static IP address, you may store the telephone number and the IP Address of this equipment into the Static Phone Book. It is not necessary to get the IP address of the other party through IP learning or joining to NETMOSA to get the IP Address of the other party. You should remember that MOSA 4600 will search the telephone number and IP Address from the Phone Book first. If any IP address is changed and the data in the Phone Book are not updated, MOSA 4600 will still take the wrong IP address from the Phone Book and try to create the path. Of course, the call will fail.

If the Private IP Address is used internally, but the global IP Address used is static IP Address, not DHCP, this line may be included in the Pone Book. The public IP Address and the virtual port of IP Sharing are stored as corresponding data.

５１＋１０

５２０

* = 10５１

＋１１

５２１

# = 11


77

In certain case, only input Phone Number and set IP/Port as 0.0.0.0/0 is possible. For example: If the trunking gateway that makes Outbound-Transit call for MOSA 4600B to PSTN uses dynamic IP, it increases the transfer speed of route information when the Phone No. of trunking gateway is configured in Phone Book in advance if the dynamic IP of trunking gateway changed.

For Web configuration, please refer to：11.15 Phone Book

10.8.1.1 Add a Telephone Number In the page of Web Management Page folder “PHONEBOOK”, under “Add Entry” :

(1) Phone Number : Enter full telephone number including Country Code and Area Code, E.g. 886282268888

(2) IP/Control Port : Enter the Static Global IP address and UDP port number. In certain case above, input 0.0.0.0/0

(3) Click button Apply

10.8.1.2 Delete a Telephone Number In the page of Web Management Page folder “PHONEBOOK”, under “Delete Entry”, enter the telephone number to be deleted in the field of “Phone Number” and click button Apply.

If you like to delete all static telephone number, please set “Delete All Static” to “Yes” and click button Apply.

10.8.1.3 Search the IP Address of a Telephone Number You may search the IP address of a telephone number. The telephone number may be stored either in static Phone Book or dynamic Phone Book ( through IP learning), hence you may find out the corresponding IP address and UDP port number used when he telephone is placed. In general, if the IP phone is failed, please search the IP address corresponding to the phone number, then check the IP address of the other party to see if it is correct. You may also search the phone number by entering NETMOSA ID.

In the page of Web Management Page folder “PHONEBOOK”, under “IP Search”, enter the phone number, which IP you like to search, in the field of “Phone Number” and click Apply. Two sets of IP address and UDP port will be displayed

IP1/Port : IP Address of Public IP and UDP port

IP2/Port : IP Address of Private IP and UDP port ( for IP Sharing). If private IP address is not used, the same data as IP1/Port will be displayed.

78

11. Description of Web Parameter Management Web of Firmware 1.06.2 is divided into Server Mode and Client Mode and its Web content are different. Please contact distributor to get free Firmware. Use different firmware can has different mode. Description of this manual is based on Firmware 1.06.3. To simplify installation procedure, some management Web page or Parameter only exists on elder version and it is removed in this version.

11.1 Basic\System Config

In the Mode of the table below, S: means Server Mode only, C: Client Mode only, Blank: share function.


79

Group Field Description Default Value Mode Region ID Display the Region ID. You can select different

country and click Modify button to change. (Don't change if your country is not listed in the options)

00 (Taiwan)

Software Version Display the Software Version (Display Only)

BootRom Version Display the BOOT ROM version (Display Only)

Hardware Version Display the Hardware Version (Display Only)

Capacity Show the max available call (Display Only) 12/36/90 Ports, depends on model

Up-Time Display the elapse time since last start

(Display Only)

Information

MAC Address Display the MAC address of HW equipment

(Display Only)

Time Source Select the method to synchronize the system date and time AutoSync：Synchronize automatically Manual：Entered manually

AutoSync

Date Enter the date manually, valid only if “Manual” is selected in Time Source, In format yyyy/mm/dd

Blank

Time Enter the time manually, valid only if “Manual” is selected in Time Source, in format hh:mm:ss

Blank

Time Zone Select the time zone which the system is located

Time Configuration

DayLight Saving Select if daylight saving applied ON：daylight saving applied OFF：daylight saving not applied

Off

Call Control Define UDP port number for packet transmission . The number is between the range of 0 – 65535. (It is activated after system re-started)

2000

Pickup Section Define the port number for Pickup Section. If you would like to pick up the call of another MOSA 4600, the Subnet Mask and Pickup Section of both sides must be same.

2999 C

UDP Port Configuration

RTP Base

Define UDP port number for voice packet transmission. The port number must be even and between the range of 0 – 65534. (It is activated after system re-started)

10000

Country Code Enter Country Code of the location where the system is. (e.g. 86 for China; 1 for America)

(Country Code by Region ID is displayed)

My Phone Number

Area Code Enter Area Code of the location where the system is. (e.g. 21 for Shanghai; 2 for Taipei)

Blank

80

Group Field Description Default Value Mode Phone Number Enter the PSTN telephone number connected Blank

Netmosa ID Netmosa ID is displayed if register to Netmosa; ”OK” is displayed if register to Netmosa PLUS

Blank

Netmosa Password Enter Password to register to Netmosa PLUS if the password is requested from Netmosa PLUS

Blank

Netmosa+ ID Netmosa+ ID is displayed if register to Netmosa+; Click Register button to register ”OK” is displayed if register to Netmosa PLUS

Blank

Netmosa+ Password

Enter Password to register to Netmosa PLUS if the password is requested from Netmosa PLUS

Blank

My ID

Netmosa ID Netmosa ID is displayed if register to Netmosa; ”OK” is displayed if register to Netmosa

Blank

System Restart

Restart Mode Select which Mode for this machine to re-start None：Don't restart system Cold Restart：Cold restart system Warm Restart：Warm restart system

None

11.2 Basic\ABBR. Dial


81

Group Field Description Default Value

Total Entries Total entries can be configured 100

Entry List Entry list for Abbr. Dial, consists: Page: Enter the page number to be displayed, page number from 1 to 5 Index: Display Abbr. Dial Index Abbr. Dial Number: Display the actual number to be dialed to make a call

Blank

Abbr. Dial Configuration

Update Entry Configure the content of Abbr. Dial. 20 entries each page: Index: Enter the index to be configured Abbr. Dial Number: Enter the digits to be dialed, maximum 27 digits

Blank

11.3 IP Setting This Management Web is divided into Server Mode and Client Mode and its Web content is different. Please contact distributor to get free Firmware. Use different firmware can has different mode.

Server Mode:

82

Client Mode:


83


84

Group Field Descriptions Default Value Mode

IP State The type of IP Address get: Manual：User enters the assigned static IP addressAuto(DHCP)：Dynamic IP address from DHCP server

Manual

Current Setting Display the current setting (current using) IP information, including IP Address, Subnet Mask and Default Gateway. (Display only)

192.168.0.2 255.255.255.0 192.168.0.1

IP Settings

Change To Enter the information to be updated to, including : 1. IP Address 2. Subnet Mask 3. Default Gateway (IP State must be at state “Manual”) After you had filled out these parameters, click button “Apply” to activate the updated value and the system must be restarted. (Warm Start)

Primary Address

IP Address of Primary DNS server. The default value is configured in advance, depending on the region of shipment. 168.95.1.1 is default for Taiwan region.

168.95.1.1 DNS Server

Secondary Address

IP Address of Secondary DNS server. Blank

Serial NumberSerial Number of Netmosa+. Default value is pre-configured. If you don't have this number, please contact with distributor. This number is required for making VODNET call

2010095953-504

03

1798363110-495

84

Netmosa+ IP Setting：

(Restart is required)

Priority The priority of the Serial Numbe above (Read Only) 1/2 IP Address Enter Netmosa IP address if register to Netmosa. Blank Netmosa IP

Setting：

(Restart is required)

Port Enter Netmosa Control Port Blank

Route Manager Setting

FONEMOSA 4498 is a Route Manager and it can manage the route of MOSA/FONEMOSA Series Machine to PSTN Sync (button): Click this button to request the related information of FONEMOSA 4498

C

Manager(1) IP/Port

The IP Address and Port Number of the first FONEMOSA 4498

0.0.0.0 /0 C

Netmosa+ ID The Netmosa+ ID of the first FONEMOSA 4498 Blank C Security Key The Security Key of the first FONEMOSA 4498 Blank C

Route Manager Setting

Manager(2) IP/Port

The IP Address and Port Number of the second FONEMOSA 4498

0.0.0.0 /0 C


85

Group Field Descriptions Default Value Mode Netmosa+ ID The Netmosa+ ID of the second FONEMOSA 4498 Blank C

Security Key The Security Key of the second FONEMOSA 4498 Blank C Collect Route Info

From Select the source of Route Info. Options: Gateway in Phone Book：Phone Book in this Machine Route Manager：Assigned by Route Manager Both：From the sources above

Gateway in Phone Book

C

Route Input the Route Number you want to inquire. Click Show button to display the result. Cost：Shows the Cost. The lowest cost will be used first. IP/Port：Shows the IP Address and Port Number of the machine of this route. Derived：When there are two route with the same cost, the route with lower Derived value will be used.

C Show Route

Show (button) Show available Route

Management Host

IP Address To work with Web management User Name, it can configure the IP Address that can manage this machine.

For example:

2. Configure to 0.0.0.0, any PC that input Web management User Name "WEB" can manage this machine.

3. Configure to 10.13.6.31, PC with IP: 10.13.6.31 that input Web management User Name "WEB" can manage this machine.

4. Configure 0.0.0.0 and change Web management User Name to "(Local)". PCs at the same IP subnet that input User Name "(Local)" can manage this machine.

5. Configure 10.13.6.31 and change Web management User Name to "(Local)". PCs at the same IP subnet or use IP: 10.13.6.31 that input User Name "(Local)" can manage this machine.

0.0.0.0

User Name USER name of Web Management Page WEB Password Password to enter the Web Management Page Blank

WEB Password

Password Confirm

Re-enter the Password for reconfirmation Blank

86

11.4 Advanced-MOSA\General This Management Web is divided into Server Mode and Client Mode and its Web content is different. Please contact distributor to get free Firmware. Use different firmware can has different mode.

Server Mode:

Client Mode:


87


Group Field Descriptions Default Value Mode Dial Ending Time

Dial Ending Time

Generally “ # ” is the last character of the number, and that means “end of dialing”. If no “ # ” is dialed, system will wait until dial ending time out. If “0” is set, it means to disable this function

3 sec

No Answer Forward Time

time When no one answers the incoming call of channels for a period of time configured here, the call is forward to specified destination.

25 sec

Slave Device Slave ID Define a MOSA 4600B SIP Line as the backup machine. This machine will find the backup MOSA 4600B SIP Line if all lines are busy. The phone number of the backup machine has to be full number, i.e. Country Code + Area Code + Telephone Number and the related connection information is registered at PhoneBook or Netmosa/Netmosa+.

Blank S

Outbound Call Progress Tone

Control When user make outbound to PSTN call, calling side might not hear the ring back tone from called side immediately. This function generates progress tone to calling side before called side machine generate ring back tone. This tone comfort calling side to wait patiently until call route is built. Disable: Don't send Progress Tone (silent) Ring Back Tone: Send ring back tone continually Confirm Tone: Send short confirm tone then silent. If music ring back tone is enabled, calling side can hear clear music.

Disable

Offnet Dial-In Authentication

Control Receive caller ID from PSTN incoming call for authentication. This is the special application of mobile extension. When it is enabled, the caller ID of PSTN incoming call (mobile phone) has to be the same as the setting in "Offnet To:" number in Web Folder: Channel/Configuration, otherwise, the incoming call is rejected. Enable/Disable

Disable C

11.5 Advanced-MOSA\Numbering Plan This Management Web is divided into Server Mode and Client Mode and its Web content is different. Please contact distributor to get free Firmware. Use different firmware can has different mode.

88

Server Mode:

Client Mode:


89


Group Field Description Default Value Mode

IP Calls only Able to make IP call only and it can not route to PSTN

IP Calls Access Code to Make IP Call ** Local Trunk Access Access Code to Fetch trunk from trunk

group 1 9

Phone set Programming Access Code to start configuration of this machine via Phone set

*0

Abbr. Dial Access Code for Abbreviated dialing *2

Call Pick Up Access Code to Pick up calls in same section

*7

Access Code

Call Pick Up with Extension

Access Code to pick up specified extension.When there is many extension ringing, press *3+Ext. No. Such as *3 888 (888 is ext. no.) That extension number is picked up by you.

*4

90

Group Field Description Default Value Mode Netmosa Plus Call Access Code to Make IP call via Netmosa

Plus ＊3

Seize Remote Trunk Access Code to Seize the Trunk group of the remote machine, but you has to obtain the permission previously. That means, in the seized side, the information of the otherside is defined in the list of Outbound Transit, the Trunk Call Allowed is set to True, and Trunk Group is set to Enable. Dialing Method : <Seize Remote Trunk Access Code> + <Country Code> +<Area Code>+<#>。 For example, there is a system in Taipei, and a system in Shanghai. You may dial the access code of “Seize Remote Trunk”, e.g. *9 8621# , from the extension line in Taipei to seize the trunk of Shanghai

*9

Seize Specific Trunk (Class)

Access Code to Seize the Specific Trunk of the remote machine, but you have to obtain the permission previously. That means, in the seized side, the information of the otherside is defined in the list of Outbound Transit, the Trunk Call Allowed is set to True, and Trunk Group is set to Enable. Dialing Method : <Seize Specific Trunk Access Code> + <Prefix> +<Class ID>+<#>.

*8

Call Retrieve When this machine is connected with Parking Server and the call is parking on the server, dial this access code to retrieve the call

*1

Assign Operator to Assign an extension line as the Operator. If operator is not assigned in this machine, set to N/A.

N/A S Other Setting

Maximum number of IP Calls

The maximum number of IP Call can be made at the same time. The default value is the number of extension line. It is recommended to plan it depending on the bandwidth. The concurrent call of Channel 90 model (SIP-90) is 40 (dialing between 2 extensions is consider as 2 calls)

9/12/36/40,

depend on

model.


91

Group Field Description Default Value Mode Maximum Concurrent Video Calls

The max video call can be made at the same time. Set this value too high affects the quality of calls.

4 S

IP Call Priority Configure the phone number searching priority for outbound call. Please refer to related chapter of PhoneBook, Outbound, NetmosaPlus 1.

PhoneBook-Outbound-NetmosaPlus：

The system search phone number according to this sequence.

2. PhoneBook-NetmosaPlus-Outbound：

Change to different sequence

PhoneBook-Ne

tmosaPlus-Out

bound

S

11.6 Advanced-MOSA\PKS

92

Group Field Description Default

Global IP Address Configure Global IP address of Parking Server

0.0.0.0

Port Configure the Port number of that Global IP address for Parking Server

0

Private IP Address Configure Private IP Address of Parking Server

0.0.0.0 IP Setting

Port Configure the Port number of that Private IP address for Parking Server

If Private IP is used, both Global and Private need to configure, otherwise, configure Global IP is enough

0

Security Setting

Key The Security Key to connect Parking Server. It needs to restart the system for the Security Key to take effect.

0

11.7 Advanced-MOSA\Prefix Map


Maximum The maximum number of equipment can be entered.

600

Entered The number of equipment has been entered 0

Prefix Map (Display Only)

Max Prefix Length The maximum length of Prefix number 6


93

Group Field Description Default Value Add/Modify Entry Add/Modify a Prefix number

Prefix : Enter the Prefix number for other equipment, maximum length is 6 Phone Number : Enter the phone number of MOSA 4600 or FONEMOSA that prefix is assigned to. This field may be the NETMOSA ID. Input English alphabet "x" means the number of the machine itself. If "x11", means phone-no-itself+11. That means the prefix number (phone number) is the equipment that you assigned to. If that machine make call to this machine, the system converts original Caller ID to prefix number according to Prefix Map here. It is easier to identify and to call back. Type : Type ( Phone/iPBX/Conf ) indicates this prefix number is assigned to (1) MOSA 4500 or FONEMOSA 4200 (Phone), (2)MOSA 4600, FONEMOSA 4400 series products (iPBX) or (3)FONEMOSA 4496 Conference Bridge (Conf). If the type is iPBX, system will start to create the call path after dialing prefix number plus 2 digit extension number (prefix ID + Ext No), or prefix number plus “0” (prefix ID + 0). Actually, the corresponding telephone number of equipment defined in the Prefix Map Table is sent out. In the later case, “0” will be treated as the access code for Operator if operator is defined in the system, otherwise the “0” after the Prefix number will be ignored. If the type is phone, system will start to create the call path after dialing the Prefix ID number. If the type is Conf, it is suitable to connect to FONEMOSA 4496 Conference Bridge

Blank

Delete Entry Delete the Prefix number Blank

Delete All Entry Delete all Prefix number No Prefix Enter the Prefix to be searched Blank Phone Number Display the phone number of equipment

defined by the searched prefix Blank

Phone Number Search

Type Display the type of equipment defined by the searched prefix.

Blank

94

11.8 Advanced-SIP\Common This Management Web is divided into Server Mode and Client Mode and its Web content is different. Please contact distributor to get free Firmware. Use different firmware can has different mode.

Server Mode:

Client Mode:


95


96

Group Field Description Default Mode Port The control port number of SIP protocol. 5060 C Port and Header

Header Form

Select ‘Standard’ or ‘Compact’ to be the header format of SIP packet. When Compact is selected, the header will be shorter and it saves bandwidth. Other SIP device also need to support this function, otherwise, the call is fail.

Standard C

Domain Name

Domain name or IP address of proxy. Blank

Disable

C Outbound Proxy Setting

Port Control port number of SIP protocol. 5060 C Registrar Setting Domain

Name Domain name or IP address of proxy that you want to register.

Empty

Disable

C

Out-band DTMF Control Enable/Disable Enable: When the other SIP device also supports this function. Disable: Disable this function.

Disable C

Incoming Call Screening

Screening Disable: Accept all incoming SIP call Enable: This machine only accepts incoming call through SIP Proxy.

Disable C

Control DID function can pass the number that SIP user dial from Phone-set directly. By this way, SIP user can dial to the extension of MOSA product without two steps dialing. For Client Mode: This function is available if SIP Proxy support. Certain range of phone number need to specify for SIP Proxy to send to destination directly. For Server Mode, DID mode is activated when it is enabled.

Enable C Direct Inward Dialing

Prefix Length

Specify the Prefix Length of the number that SIP user dial from Phone-set. Digits after Prefix can be identify by MOSA 4600B SIP Line for call transit to Extension or certain machine (by using prefix number). For example: User dial 8226123. If you specify this field to 4, then this machine will delete first 4 digits 8226 and use extra 123 to compare with the Prefix Table, then dial the real phone number according the table.

0 C

Release Call by Checking RTP

Check RTP packet to see if the line is still alive. If the setting is configured to 5 mins, then the system checks it every 5 minutes. If RTP packet is not found, the line is disconnected.

5 mins C Check Alive

OPTIONS Enable or Disable this checking procedure Disable C


97

Group Field Description Default Mode Register Expires expires When this machine is configured as Client Mode, it

registers to SIP Proxy before timeout value configured here repeatedly. It keeps the registration status with SIP Proxy, because SIP Proxy may terminate connection when this machine is idle.

3600 C

G.729AB: Mark the selection to Enable this Codec Enable

G.723.1: Mark the selection to Enable thisCodec Enable

PCMU: Mark the selection to Enable this Codec (G.711 u Law)

Enable

PCMA: Mark the selection to Enable this Codec (G.711 A Law)

Enable

Codec Type

iLBC: Mark the selection to Enable this Codec Enable

Codecs Selection

Codec Priority

You can select the codec priority for your requirement. Not selected items at the table above will not be used.

G729-G723-iLBC-PCMU-PCMA

Register-All (button)

Click this button to let all SIP Entities to register to SIP Proxy Server

C SIP Entity Control

DeRegister-All (button)

Click this button to let all SIP Entities to quit registration from SIP Proxy Server

C

H.264: Mark the selection to Enable this Codec Enable S


Codec Type


Video Codecs Selection

Codec Priority

You can select the codec priority for your requirement. Not selected items at the table above will not be used.

H.263- H.264 H.261

S

SIP Entity Select an entity and click Select button to display follow items’ setting of SIP entity section. Select: Select Button

1

Entity Control

Select Enable/Disable the Entity Enable

SIP Entity

Register Status

Show the register status, if it shows Registered means successful. (Read only) Register: Register Button De-Register: Cancel Register Button

Blank C

98

Group Field Description Default Mode Address Enter SIP phone number of this Entity. The phone

number general assigned by SIP service provider. 1234501~1234590, to map Entity 1 ~ Entity 90 (Elder: 1234567)

C Public Address Setting

Default Account

Account information to register SIP Proxy Username: Possibly the same as your SIP phone

number. Password: Password for registration Confirm Password: Confirm again

C

Name Enter Contact Address. This function is for direct call between two machines without proxy. It is better that this Name is the same as Public Address.

1234501~1234590, to map Entity 1 ~ Entity 90(Elder: 1234567)

C Contact Address Setting

Current Setting

Display current setting of Contact Address

01 C

Channel Show the all channels Depend on model

S SIP Entity Members

Entity Show " * " means this channel had joined SIP Entity. - S

11.9 Advanced-SIP\Inbound Auth (Server Mode Only)

This Web page applys to Server Mode only and no such page for Client Mode.


99

Group Field Description Default Realm Enter domain name or IP address of this

machine MAC Address

Maximum Maximum number of entries allowed

(Read Only) 20

Entered Number of entries of authentication entered.

(Read Only) 0

Display the entries (Read Only) Entries List Entity: Which entity that you select. Username: Username of authentication. Password: Password of authentication.

Empty

Update Entry Enter entries of authentication Entity: Which entity that you select. Username: Username of authentication. Password: Password of authentication. Confirm Password: Enter password again for confirmation.

Empty

SIP Inbound Authentication

Delete Entry Delete entries of authentication Entity: Which entity that you want to delete.Username: Username of authentication.

Empty

100

11.10 Advanced-SIP\Registrar (Server Mode Only) This Web page applys to Server Mode only and no such page for Client Mode.

Group Item Description Default Value NAT Traversal Keep mapping Whether or not to send Option Packet to NAT

device to avoid line disconnection. ON/OFF

ON

Max. Expires Time

Expires (sec) When the SIP device that register to this machine fail to response any packets for a period of time configured here, this machine disconnect the connection. (Min. 30 sec.)

3600

Min. Expires Time

Expires (sec) How min time does SIP device send packet to confirm registration to this machine. The registration time of SIP device should be longer then this time, otherwise, the machine respond error message to the same one SIP device with repeat request.

30

Current No (Public Address):

Shows the volume of registered SIP devices. (Counted by Public Address)

(Read Only) Registered List

Current No (Contact Address):

Shows the volume of registered SIP devices. (Counted by Contact Address)

(Read Only)


101

Group Item Description Default Value Contacts List: Lists the registered SIP device. It

contains User: SIP phone number Contact URL: Public Address used by SIP device Expires (sec): Time-out durationControl: DeRegister button. Clickthis button to suspend registration of that SIP device.

(Read Only)

11.11 WAN IP (Client Mode Only) This Web page apply to Client Mode only and no such page for Server Mode.

102

Group Item Description Default Value

NAT WAN IP Address Input NAT WAN IP helps this machine to penetrate NAT without using STUN Server. When you use this function, the port number inside and outside NAT device must be consistent.

If NAT device use dynamic IP (PPPoE), you can input 255.255.255.255, the system will seize WAN IP of NAT device. If you use dynamic IP, works with VDNS may be recommended; otherwise, registration is fail if IP is changed.

Attention: The RTP port number (usually 10000) and Signaling port number (usually 5060) inside and outside NAT device must be consistent. And, Configure Server Port to this machine is also required

255.255.255.255

NAT WAN Active IP

Address Current used NAT WAN IP Read only

11.12 Advanced-SIP\Diagnosis

If there is any condition of network problem, you can refer to this page for related information. Click Clear to clean the data on this page.


103

11.13 Channel\Summary

Group Item Description Default Value

Channel Show the Channel number. (Read Only) 1~90, depends on model

Status Show the status of Channel

Enable: Channel is usable

Disable: Channel is closed

(Read Only) Enable

Start-Time Show the start time if the line is busy.

(Read Only) -

Duration Show the duration of this call. Click Refresh of browser to show the latest duration.

(Read Only) 0

SIP-ID The SIP number used for incoming call from SIP device or outgoing call from MOSA 4600B SIP Line.

(Read Only) -

MOSA-IP/PORT The IP address and port number of MOSA machine used for this channel.

(Read Only) -

11.14 Channel\Configuration This Management Web is divided into Server Mode and Client Mode and its Web content is different. Please contact distributor to get free Firmware. Use different firmware can has different mode.

104

Server Mode:


105

Client Mode:


Group Field Description Default Value Mode Channel Select the port number to be configured 1 Extension Number

The extension number that is defined to this selected port

10

106

Group Field Description Default Value Mode Port State Activate or shut down all functions of selected

port Enable : Activate all functions to selected port Disable : Shut down all functions to selected port

Enable

Current State Display the current status (Display only) Enable : Selected port is enable Disable : Selected port is disable

Enable

Information

Do Not Disturb When this function is activated, only outgoing call of this channel is available. Any incoming call is busy with busy tone. Enable: function is activated. Disable: function is disabled.

Disable

Control Enable or disable the function “Call Forward” Forward-Disable: Disable the function. Forward-All Calls: Forward all calls. Forward-Busy: When the channel is busy, the calls will be forwarded. Forward-Busy-Slave: When the channel is busy the calls will be forwarded. If the destination is also busy, and it is also configured as Forward-Busy-Slave. The call will continue forwarding to the next. NoAnswer-Forward: When there is no answer for this channel, the call forward to the specified destination. Busy/NoAnswer-Forward: When there is no answer or line busy for this channel, the call forward to the specified destination.

Disable Call Forward

Forward to (Gateway Phone Number)

Forward the call to the Machine or NETMOSA telephone number you specified. The entered telephone number must contain full telephone number, including country code, and area code.If the "Offnet to" number is also configured, the call will offnet to PSTN via the machine that the phone number is configured as "Forward to" here.

Blank


107

Group Field Description Default Value Mode Offnet to

(Offnet Phone number)

Forward the IP call that is coming (or forwarding) from other machine to PSTN. The Offnet to number here is for the call offnet to PSTN. For example, the local machine is located in Taipei. The MOSA that will forward your call is located at Shanghai, phone No. 21-6445-1111 (this No.+ country code is configured as "Forward to" No. 86-21-6445-1111) and you want to make a PSTN mobile phone call to Shanghai No. 1360567888, so you configured 1360567888 as "Offnet to" No here. And the “Permitted Phone Number for Offnet Forward” of FONEMOSA in Shanghai should be configured to “1360567888”.

Blank

Barring Class

ID Enter the Barring class for selected port 0 (Disable)

Outbound Transit Control

Privilege Define the privilege for Outbound Transit call Disable : Outbound Transit call is not allowed Local : Outbound Transit call to local call only Toll : Outbound Transit call to mobile phone and Toll call International : Outbound Transit call to international call The local call, toll call, or international call is judged from the point of the My Phone Number defined in this machine.

International

Join Operator Group

Yes/No Define whether to join into Operator Group or not.Yes : join into Operator Group to behave as Operator No : Don't join.

Yes S

My Pick Up Group

Group ID Select the Pick UP Group that this channel joins. One channel can join one Pick Up Group only. The Channel with the same Pick Up Group can pick up each other's call. OP: Operator's group can pick up 1~9: Select other Pick Up Group.

OP S

Pickupped By Others

Control Define whether the call will be picked up by others True : Allowed to be picked up False : Not allowed to be picked up

True S

Soft Key Soft Key String Define the characters string of softkey. When the softkey is triggered, the string of softkey will be dialed. The maximum length of string is 22 digits.

**

108

Group Field Description Default Value Mode Trigger Mode Choose the Trigger mode to trigger the softkey :

Key Press : If the digits dialed matches with any one of the digits defined in Trigger Digits, the softkey is triggered and the number defined in softkey string will be dialed. Auto : For FXS, it is triggered when phone-set in hook off status. For FXO, it is triggered when line is ringing.

Key Press

Trigger Digits Define the trigger digits to trigger the softkey e.g. define trigger digits as 123. softkey will be triggered if 1 or 2 or 3 is dialed.

#

Append Trigger Digit

Define if the trigger digit will be appended to the softkey sting as the last digit when dial out Not Append : Not appended Append : Trigger digit is Append.

Not Append

FXO Output: dB / Input: dBAdjust volume of FXO channel. It is adjustable at Input and output sideOutput: dB / Input: dB

0 Voice Gain Tuning

FXS Adjust volume of FXS channel. It is adjustable at Input and output sideOutput: dB / Input: dB

Attention: When you adjust this configuration, the volume of the whole system needs to be under consideration. Keep it balance for gain upward or downward, otherwise, poor voice quality happens when gain is increased too much or voice is too quiet when gain is decreased too much.

0

Virtual Device

SIP URI The mapping of this channel to SIP Entity number. In Server mode, input example such as 8801. In Client mode, input SIP account such as SIP ACCOUNT@Porxy Server, example: [email protected], [email protected] (The Public Address or Contact Address of SIP Extension)

1010~1099, depends on model

2833 In Use Show the status of 2833 DTMF No Join SIP Entity Select a SIP Entity for this Channel to join to.

SIP Information

Video Control Configure this channel to join Video call? Enable: Able to make video call Disable: Not able to make video call

Disable


109

11.15 Phone Book

Group Field Description Default Value Phone Number Search the IP address of the frequently used

equipment by telephone number. The full phone number including Country Code + Area Code + Telephone Number should be entered

Blank

IP1/Port Display IP Address of Public IP (Display Only)

IP Search

IP2/Port Display IP Address of Private IP (Display Only) Phone Number Add or modify the telephone number (including

Country Code and Area Code) in Phone Book Blank Add Entry

IP/Control Port Add or modify the IP Address or UDP Blank Delete Entry Phone Number Delete telephone number (including Country code

and Area Code) from Phone book Blank

Delete All Static Entries

Delete all static entries from the Phone Book or notYes : Yes, delete all No : No

No

Maximum The maximum number of telephone number can be entered

(Display Only) 256

Entered The number of telephone number had been entered

(Display Only) 0

Entered List List of telephone number entered (Display Only) Blank

110

11.16 Access Code


111

Group Field Description Default Value International Access Code

Outgoing Call Carrier Selection Access Code

Code for an international call dialed from system, and only one code can be entered

002

All the Access Codes could be Dialed

System has to know all possible access code for making an international call, in order to check if the call is an international call. In some countries there are several access codes for making international call. All those access codes have to be entered, in case some access code can not be recognized. e.g. in Taiwan, 002/005/006/009/012/019 are the access code for international call.

Maximum The maximum number of the access code for international call (Display only)

10

Entered The number of the access code had been entered (Display only)

6

Entries List Display the list of possible access code entered for international call (Display only)

002，019，005，006，

007，009

Add Entries Add the possible access code, four entries can be entered in one time

Blank

Delete Entries Delete the access code from the list, four entries can be entered in one time

Blank

Outgoing Call Carrier Selection Access Code

Code for a Toll call dialed from system, and only one code can be entered

0

All the Access Codes Could be Dialed

System has to know all possible access code for making a toll call, in order to check if the call is a toll call. In some countries there are several access codes for making toll call. All those access codes have to be entered, in case some access code can not be recognized. e.g. in Taiwan 0/1805/1806/1807 are the access code for toll call.

Maximum The maximum number of the access code for toll call (Display only)

Entered The number of the access code had been entered (Display only)

1

Long Distance Access Code

Entries List Display the list of possible access code entered for toll call (Display only)

0

112

Group Field Description Default Value Add Entries Add the possible access code, four entries

can be entered in one time Blank

Delete Entries Delete the access code from the list, four entries can be entered in one time

Blank

In some countries, the conflict exists in the numbering of Area Code. For instance, Area Code 4 is assigned to area-A, and 47 is assigned to area-B with the same starting digit. Therefore when a call is from area-A to area-B, the dial number will be the access code for toll call “0”, then Area Code “47” and phone number. Those kinds of conflict make MOSA 4600B confused. In such cases, any exceptions must be stored in the system to avoid from any misunderstanding. For instance, MOSA 4600B is installed in area-A with Area code 4, then any Area Codes starting with 4 (47 for area-B, 49 for area-C..) but different areas to area-A are exceptions. All exceptions must be known by system.

Capacity Maximum exceptions about Area Code can be entered (Display only)

5

Quantity The number of exception had been entered (Display only)

0

Code List Display the list of exceptions entered (Display only)

Blank

Add Entries Add the exceptional Access Code, four entries can be entered in one time

Office Code Exception

Delete Entries Delete the exceptional Access Code from the list, four entries can be entered in one time

In some countries, several area codes are applied in a big range. The calls between different area codes are treated as local calls; no access code for toll is required; the tariff is also based on the local call. Those area codes must be entered in Toll Code Exception otherwise MOSA 4600B will treat those calls as toll call

Maximum Maximum exceptions can be entered

(Display only)

10

Entered The number of exception had been entered

(Display only)

0

Entries List Display the list of exceptions entered

(Display only)

Blank

Add Entries Add the exceptional Code, four entries can be entered in one time

Blank

Toll Code Exception

Delete Entries Delete the exceptional Code from the list, four entries can be entered in one time


113

Group Field Description Default Value Leading Digits of Local Calls

Control In some areas, the area code is the must code even it is a local call. Or in some areas, the access code for toll and the area code is the must code whatever it is a local call or toll call. Define here for special control. ♦ None: Disable ♦ Area Code: the Area Code is always the

leading digit when dialing ♦ Access Code + Area Code: the Access

code and Area Code is always the leading digit when dialing

Disable

11.17 File Transfer\Download

Group Field Description Default Value File Download CFG (button) Click this button to download the CFG file of

this machine and it can be saved in HDD of

the computer for backup. For some reason

that you do Factory Reset, this file help your to

restore to original state. CFG file keeps the

related data that is configured by VODTEL or

you.

114

Group Field Description Default Value MEM (button) Click this button to download the MEM file of

this machine and it can be saved in HDD of

the computer for backup. For some reason

that you do Factory Reset, this file help your to

restore to original state. MEM file keeps the

related entries that are input by you. Please

refer to 13.2 Download and Modify MEM file

11.18 File Transfer\Upload

Group Field Description Default Value File Upload Select file: Browse (button): Select the file that will upload

to this machine from Computer. Apply (button): Executes upload. For different kinds of file, system may Restart when upload is done. During Restart period, the Web Pages is not accessible, please wait a moment. If the file uploaded does not take effect immediately, please go to Web Folder: Basic\System Config and do Restart (RUN: Cold-Restart, WEB: Warm Restart) manually. Revert (button): Clear selected file path and file name.

RUNTIME Show the information of RUN file, including Size Date Time


115

Group Field Description Default Value WEBPAGE Show the information of WEB file, including

Size Date Time

11.19 License Upgrade


License Upgrade

Current License Available counts of current License, based on Concurrent Call available.

Depends on model

Box Info To apply License Upgrade (increase available Concurrent Call), please use the Box Info of this machine that shows at this page to submit and purchase License Upgrade Key from VODTEL

Depends on machine. Each one is different.

Apply (button) When Upgrade Key (as below) Authentication (as below) is input, click this button to do License Upgrade

Attention: If you did not purchase License Upgrade Key from VODTEL, don't input any key and try to upgrade, otherwise, machine will be locked with several times of failed upgrade

Upgrade Key Use data of Box Info above to purchase and get License Upgrade Key from VODTEL

Blank

116


Authentication Input Box Info, License Upgrade Key into the License Upgrade Web of VODTEL, and then get Authentication Data

Blank

Result When user click Apply button, System shows the result of License Upgrade (successful, fail, reason)


117

12. Use Private IP Behind NAT The MOSA unit is able to communicate with other MOSA units or SIP Phone under a NAT environment using Private IP addresses on the LAN side of your IP Sharing device.

Concerning about NAT, please refer to the documentation about NAT.

In the table followed, the port number used in MOSA 4600B SIP Line is listed. If the packets for MOSA 4600B SIP Line are blocked by the firewall, open the ports with port number listed in the table in the firewall.

Packet Type Port Number

Control UDP 2000

SIP UDP 5060

RTP voice packet UDP 10000 ~ 10999

FTP firmware upgrade TCP 21

Web Management TCP 80

Telnet TCP 23

If there is several MOSA 4600B in the LAN, the port number used for each machine should be different, such as UDP 2010 UDP 5062 and UDP 11000~ 11999 for another machine. Open each port numbers at firewall the same as above. Make calls between each MOSA 4600B by VODNET number.

Normally every type of server uses the specific port number, e.g. WEB server uses the TCP port 80, and FTP server uses the TCP port 21. The configuration is to set mapping for the specific port number to the internal private IP Address. Therefore IP sharing device will transfer the packet with specific port number to the corresponding private IP Address. For example, if the private IP Address 192.168.1.1 is used in the internal network, it should be mapped to a corresponding port number (TCP port 80 of IP sharing devices <--> TCP port 80 of IP address 192.168.1.1). Hence, any packets to TCP port 80 will be transferred to TCP port 80 of IP Address “192.168.1.1”. In this bridge, UDP port 2000 is used for Call Control. It acts the same as a server. Only the port number is different. So there should has a port mapping on the IP Sharing device. (UDP port 2000 of IP sharing devices <--> UDP port 2000 of IP address 192.168.1.1). If there is more than one MOSA SIP Line under the same NAT, it needs to separate different 2000 and 5060 one by one. For example, if the first machine uses 2000, the second may use 2002…and so on.

118

13. File Management 13.1 File Type The naming convention to the file type of MOSA 4600B SIP Line is listed in the following table:

File Name File Type Description

(SE449712.CFG) (SE449736.CFG) SE449790.CFG

System configuration file File of system configuration

(SE449712.RUN) (SE449736.RUN) SE449790.RUN

Executing file System Software

SE4497.WEB Web file Page for web browser

SE4497.MEM Text File

This file can be downloaded by FTP and open it with Notepad or other text editor. Upload it when the data inside is updated.

It contains Permission List Of Outbound Transit、Static Phone book, Abbr. Dial, Location-Server and Prefix Map.

COLDSTART Cold start

It is a pseudo file. Machine will execute the cold start if this file is deleted via FTP. It is a convenient function if cold start is required after software updated via FTP

WARMSTART Warm start

It is a pseudo file. Machine will execute the warm start if this file is deleted via FTP. It is a convenient function to execute warm start via FTP.

13.2 Download and Modify MEM file MEM file records lots of customized data which user creates from Web. MEM file can be downloaded from Machine by FTP (refer to...) or by WEB (refer to 11.17 File Transfer\Download). Open the file either by Notepad or other word process software, and modify the data; then upload the file to Machine. If there are lots of data need to create or modify, use this way can save lots of time.

You will find a file SE4497.MEM on the screen of FTP, it is data file of Prefix Map table, Permission list of Outbound transit, Abbr. Dial, Location-Server and static phone book.

Please download SE4497.MEM to PC and open it with Notepad. Please refer to the following figure:


119

You are able to edit or add the text file by Windows Notepad software. After it is done, upload it back to machine by FTP, then the data on machine is updated.

Delete Record

Note: The Machine had already kept all of the data before you download the .MEM file. So the data is not removed if you remove records (all or partial) of the .MEM file and upload to machine by FTP again.

If you need to remove any records, you should. Remove record from Web page Add special mark to MEM file. Follow the way below:

Example 1: Delete a Prefix Number record Original MEM data 3000 882994546 0 Add delete mark and remove its number as below 3000! Save the file and upload it to machine again, then the record is removed. Example 2: Delete the whole Phone Book Original MEM data [PHONE-BOOK] 88994326 203.204.89.31 2000 88994381 10.13.6.185 2000 88956381 61.220.13.25 2000 Add delete mark and remove all record of Phone Book as below [PHONE-BOOK]~ Save the file and upload it to machine again, then all records of Phone Book is removed.

120

File Items

Here is the description of each item:

Field 1 Field 2 Field 3 Field 4

PREFIX Prefix Phone Number Type

1：iPBX

0：Phone

N/A

OUTBOUND-TRANSIT MAC Address Phone Number Route Type

1：Local

2：Toll

3：Specified

Trunk Call Allowed

1：True

0：False

PHONE-BOOK Phone Number IP Address Port Number N/A

ABBR-DIAL Abbreviated Number (index)

Full Number (Abbr. Dial Number)

N/A N/A

LOCATION-SERVER The first and 2nd lines are the IP of NETMOSA PLUS

The third line is the IP of NETMOSA

The first and 2nd lines are the Port No. of NETMOSA PLUS

The third line is the Port No. of NETMOSA

N/A N/A

Remarks for Update Software of File Type MEM

After the configuration is finished, please make a backup file for CFG file. It is in case that if the data is lost, you may upload the backup file of CFG file to machine. If you upload the previous backup file of CFG file to machine after the MEM file is uploaded, the MEM file will be ineffective because the backup file overwrites the Prefix Map table. You have to re-upload the updated MEM file to machine to get the correct data.

Generally speaking, CFG and MEM file should keep consistent. MEM file can create (modify or delete) lots of data without using WEB interface. When it is done and upload to this machine, please download CFG file for backup. When system data is damaged, you can restore to original setting with CFG file.

13.3 Software Upgrade

13.3.1 Software update via WEB Software upgrade can be done via FTP or Web. Upgrade by Web is easier. To upgrade system via


121

Web, please refer to 11.18 File Transfer\Upload

13.3.2 Software update via FTP 13.3.2.1 The preparation before updating FIRMWARE

1. Power on this machine

2. Get Windows based PC ready

3. LAN cable is well connected (for FTP)

4. Configure IP address, Subnet and Default Gateway for PC and this machine

5. Back up CFG and MEM file by FTP (for how to use FTP, refer to the FTP paragraph below)

6. Get the file of update “GW FIRMWARE” ready

13.3.2.2 Software Update by FTP for File Type RUN and WEB 1. Execute FTP Client Software, e.g. CuteFTP

Enter IP Address, User Name (default is FTP), Password (the password of FTP and Console is same, and the default is blank), and the Port Number to 21

2. Click button Connect to get connection between Machine and FTP Client. The files of Machine will be displayed on the window if the connection is successful.

122

3. Select the file with extension of .RUN and click button Upload and then Overwrite. Then select .WEB file and Upload/Overwrite as the same way. (Please notice that the file name must be same as the file name in the Machine).

4. After the file is overwritten (you may check if the time of the file is updated), Machine has to run Cold Start to store the configure file, then the updating is effective.

5. Check if the uploading is successful, you enter the Web Management Page to examine the version of software.

Check Version here! This manual is for 1.06.4


123

13.3.2.3 Use system console to do factory reset (Skip these steps if system work well)

Configuration by system console：or by Telnet, Start Run Telnet 192.168.0.2 in Windows

Type command below

SIP Line (12) >enable

SIP Line (12) #configure

Enter configuration commands, one per line. End with CNTL/Z

SIP Line (12) # delete nvram keep_ip

This command resets the system with factory defaults.

All system parameters will revert to their default factory settings. All static

and dynamic addresses will be removed.

Reset system with factory defaults, [Y]es or [N]o? Yes

13.3.2.4 Restore CFG, MEM file After the software is updated OK, upload original .CFG and .MEM file back to machine by FTP or Web page to restore original setting, then the system is ready to work.

124

14. Management by System Console When these commands below are executed, it may have sub-level command. Type "?" any time and press Enter to see the instruction for help.

User Exec commands： Enable Turn on privileged commands Exit Exit from the EXEC Help Description of the interactive help system Show Show running system information

show：

dns Show the IP address of domain name server ethernet FastEthernet port status and configuration history Display the session command history Ip Display IP configuration running-config Show current operating configuration version System hardware and software status

Privileged Mode：

configure Enter configuration mode delete Reset configuration disable Turn off privileged commands exit Exit from the EXEC help Description of the interactive help system ping Send echo request to destination reload Halt and perform cold start restart Halt and perform warm start show Show running system information

Global Mode：

Dbflush DataBase flush Dns Set the IP address of domain name server End Exit from configure mode to privileged mode Exit Exit from configure mode Help Description of the interactive help system Ip Global IP configuration subcommands Manager Enable/Disable the specific management

function, including Enable/Disable management of FTP, Telnet and Web.

No Negate a command or set its defaults Password Modify password of enable command regional_id Set regional id service_port Set service port number terminate Force channel clear down


125

15. Specification Capacity

Divided by the SIP extensions available, they are three models with 12/36/90 extensions (Standard form model, is suspended now). All of them are stackable and it can be stacked up to 600 machines (total 90x600=54000 extensions) in a single system.

Processing Power, able to support SIP registration of both Internet and LAN user

Extensions Busy Hour Call Attempt Traffic (Erlang)

12 1372 1

36 1248 1

90 1248 0.4

For small form model (currently sold), there is only one model wth 90 SIP ports and 9 concurrent call. Dialing between extensions is considered as 2 concurrent calls. Upgrade with charge is available and please contact with distributor.

Support Standard Protocol

RFC-3261

RFC-2833

RFC-2543

Support Audio Codec G.729A/B G.723.1 PCMU (G.711μLaw) PCMA (G.711 A Law) iLBC

(Codec priority is changeable)

Support Video Codec H.261 H.263 H.264

(Codec priority is changeable)

Network interface

Ethernet port x 2 (Small size model: 5 ports)

126

10BASE-T/100BASE-TX Auto-negotiation

RJ-45 Connectors

Management

Management Tools: Web browser, VT-100 console, Telnet

IP Address: Static IP address（Public or Private IP）

Firmware update: FTP, Web

Other specification

Power: External adapter

Voltage: 100 VAC ～ 240 VAC，Frequency：50/60 Hz

Power Consumption: 10 W

Dimension: 172 mm x 35 mm x 176 mm (Standard Form model, is suspended now) 129 mm x 23 mm x 80 mm (Small form model, currently sold)

Working Environment: Operating Temperature: 0° to 50° C， Storage Temperature:-10° to 70° C

MOSA SIP PBX Function (Need to Work with Other VODTEL Machine) Auto Attendant (DISA)

Network Operator Group

Call Transfer

Call Forward (Network forward / PSTN Offnet forward)

Barring Class

Call Pick Up Group

Call Pick Up with Extension

PSTN-IP-PSTN transit call

Auto Routing Control / Least Cost Routing

Line Group

Trunk Group

Trunk Class

Automatic Trunk Selection

Specific Trunk Selection


127

Abbreviation Dialing

Call Hold Music

CDR (Call Detail Record) for Billing

Call Park

Call Hold

Secretarial Intercept function

Conference call

Vodeo call

VoIP Broadcast Call

DND (do not disturb)

Dialer

Mobile extension

Works with traditional IP-PBX

Stackable and Networking function

DCC NO. 9171003506

mosa 4600b sip line user manual v6 english - … · 7.3.1 configure mosa 3700 as client ... sip...

Documents