motor 60z02152 - 02[1]cat 3306

4
Desmontagem e Montagem 3306 VEHICULAR ENGINE FOR 966R WHEEL LOADER Cylinder Liners SMCS - 1216-11 ; 1216-12 Remove Cylinder Liners start by: a) remove pistons 1. Check to be sure that all coolant has been removed from the cylinder block. 2. Cover the crankshaft bearing journals before the cylinder liners are removed. TYPICAL EXAMPLE 3. Remove the cylinder liner with tooling (A). Install Cylinder Liners Fechar o SIS Tela anterior produtos: ENGINE - MACHINE Modelo: 3306 ENGINE - MACHINE 58Z Configuração: 966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE Número de Mídia -SENR2410-00 Data de Publicação -01/08/1981 Data de Atualização -11/10/2001 Page 1 of 4 966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE(Z... 29/1/2009 https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Upload: ismael-de-jesus-andrade

Post on 09-Jul-2016

237 views

Category:

Documents


2 download

DESCRIPTION

Motor 60Z02152 - 02[1]CAT 3306

TRANSCRIPT

Page 1: Motor 60Z02152 - 02[1]CAT 3306

Desmontagem e Montagem 3306 VEHICULAR ENGINE FOR 966R WHEEL LOADER

Cylinder Liners

SMCS - 1216-11 ; 1216-12

Remove Cylinder Liners

start by:

a) remove pistons

1. Check to be sure that all coolant has been removed from the cylinder block.

2. Cover the crankshaft bearing journals before the cylinder liners are removed.

TYPICAL EXAMPLE

3. Remove the cylinder liner with tooling (A).

Install Cylinder Liners

Fechar o SIS

Tela anterior

produtos: ENGINE - MACHINE Modelo: 3306 ENGINE - MACHINE 58Z Configuração: 966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE

Número de Mídia -SENR2410-00 Data de Publicação -01/08/1981 Data de Atualização -11/10/2001

Page 1 of 4966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE(Z...

29/1/2009https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Page 2: Motor 60Z02152 - 02[1]CAT 3306

1. Clean the cylinder liners and block.

2. Install the liners in the block without the O-ring seals.

3. Install tooling (A) and two 5/8"-11 NC bolts 41/2 in. long. Tighten the bolts evenly in four steps: 5 lb. ft. (7 N·m), 15 lb. ft. (20 N·m), 25 lb. ft. (35 N·m) and 50 lb. ft. (70 N·m).

4. Check the liner (projection) height with tool group (B) at four locations around the liner. The difference between the four measurments must not be more than .002 in. (0.05 mm).

5. The liner (projection) height must be .0020 to .0056 in. (0.051 to 0.142 mm). The measurement between liners next to each other, must not be more than .002 in. (0.05 mm) difference.

NOTE: If the liner is turned in the bore, it can make a difference in the liner (projection) height.

Page 2 of 4966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE(Z...

29/1/2009https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Page 3: Motor 60Z02152 - 02[1]CAT 3306

6. If the liner (projection) height is not .0020 to .0056 in. (0.051 to .0142 mm), check the thickness of the liner flange (1) and depth of the liner bore (2) in the block (3). The thickness of the liner flange must be .4048 ± .0008 in. (10.282 ± 0.020 mm). The depth of the liner bore in block must be .401 ± .001 in. (10.19 ± 0.03 mm).

NOTE: If the liner bore in the block is worn and the measurement is not correct, the liner bore can be corrected with a cylinder block counterboring tool. See SPECIAL INSTRUCTIONS, FORM FM055228.

7. Put a mark on the liner and block so the liner can be installed in the same position from which it was removed.

Page 3 of 4966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE(Z...

29/1/2009https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Page 4: Motor 60Z02152 - 02[1]CAT 3306

8. Install new seals (4) on the cylinder liners. Put liquid soap on the seals and in the bores in the cylinder block.

TYPICAL EXAMPLE

9. Put clean engine oil on band (5) and install it on the liner as shown. Put clean SAE 30 oil on the liner and install it immediately in the cylinder block with tool group (C).

end by:

a) install pistons

NOTICE

The liners must be installed in the cylinder block immediately after band (5) is installed. Make sure the marks on the liners and the cylinder block are in alignment when the cylinder liners are installed.

Direitos Autorais 1993 - 2009 Caterpillar Inc. Todos os Direitos Reservados. Rede Particular Para Licenciados SIS.

Thu Jan 29 16:11:04 UTC-0300 2009

Page 4 of 4966R WHEEL LOADER 58Z00001-UP (MACHINE) POWERED BY 3306 ENGINE(Z...

29/1/2009https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...