motors iron
TRANSCRIPT
-
8/8/2019 Motors Iron
1/18
Low VoltageInduction MotorsCatalogue-2009/04 E
TAC-CCAST IRON Frame
Size 71->355
0,18-315 kW
t-telectric.com
-
8/8/2019 Motors Iron
2/18
-
8/8/2019 Motors Iron
3/18
Insulation
Ambiant temperatures / high altitudes
Motors are designed for a maximum ambianti temperature
environment of 40C and a maximum altitude of 1000
meters above sea level. If temperature and/or altitude is
higher, motor should be derated according to tables below.
Ambient temperature, C 30 40 45 50 55 60* 70* 80*
Permitted output, % of rated output 107 100 96,5 93 87 82 65 50
Height above sea level, m 1000 1500 2000 2500 3000 3500 4000
Permitted output, % of rated output 100 96 92 88 84 80 76
Motor wound for 230V 400V 500V 690V
Connected to 50Hz 220V 230V 380V 415V 500V 550V 660V 690V
% of values at 400V 50Hz
Output 100 100 100 100 100 100 100 100
In 182 174 105 98 80 75 61 58
Is/In 90 100 90 106 100 119 90 100
Ts/Tn 90 100 90 106 100 119 90 100
Tmax/Tn 90 100 90 106 100 119 90 100
3
In most cases the standard rated outputs of
motors from T-T Electric are based on the tem-
perature rise for insulation class B. Where the
temperature rise is according to class F, this is
specied in the data tables.
However, all motors are designed with class F
insulation, which permits a higher temperaturerise than class B. The motors, therefore, have a
generous overload margin. If temperature rise
to class F is allowed, the outputs given in the ta-
bles can generally be increased by about 12%.
Temperature limits are according to standards.
The extra thermal margin when using class F
insulation with class B temperature rise makes
the motors more reliable.
C
180
F HB
10
40 40
15
80105
125
155
130
120
40
10
40
Thermal margin
Permissible
temperature rise (K)
Maximum
ambient temperature
Insulation class
Other voltages
Motors wound for a given voltage at 50 Hz can also be
used for other voltage. Recalculation factors for current and
torque are given below, efciency, power factor and speed
remain approximately the same.
Guaranteed values available on request.
*High temperature grease and reduced greasing intervals recommended
-
8/8/2019 Motors Iron
4/18
Motors used at 60 Hz
Motor wounded
or 50 Hz andAt 60Hz
At 60 Hz, percentages o values at 50 Hz
Power Speed Current Is/In Tn Ts/Tn Tmax/Tn
220 V220 100% 120% 98% 83% 83% 70% 85%
255 115 120 100 100 96 95 98
380
380 100 120 98 83 83 70 85
415 110 120 98 95 91 85 93
440 115 120 100 100 96 95 98
460 120 120 100 105 100 100 103
415
415 100 120 98 83 83 70 85
460 110 120 98 95 91 85 94
480 115 120 100 100 96 95 98
500
500 100 120 98 83 83 70 85
550 110 120 98 95 91 85 94575 115 120 100 100 96 95 98
600 120 120 100 105 100 100 103
Bearings and terminal box
Standard bearing type Cable entry
Type Pole D-end N-end mm
71 2,4,6,8 6202 2RS/C3 6202 2RS/C3 2-M25X1,5
80 2,4,6,8 6204 2RS/C3 6204 2RS/C3 2-M25X1,5
90 2,4,6,8 6205 2RS/C3 6205 2RS/C3 2-M25X1,5
100 2,4,6,8 6206 2RS/C3 6206 2RS/C3 2-M25X1,5
112 2,4,6,8 6206 2RS/C3 6206 2RS/C3 2-M32X1,5
132 2,4,6,8 6208 2RSC3 6208 2RS/C3 2-M32X1,5
160 2,4,6,8 6209 2RS/C3 6209 2RS/C3 2-M40X1,5180 2 6211 2RS/C3 6211 2RS/C3 2-M40X1,5
180 4,6,8 6311 2RS/C3 6211 2RS/C3 2-M40X1,5
200 2 6212 2RS/C3 6212 2RS/C3 2-M50X1,5
200 4,6,8 6312 2RS/C3 6212 2RS/C3 2-M50X1,5
225 2 6312/C3 6312/C3 2-M50X1,5
225 4,6,8 6313/C3 6312/C3 2-M50X1,5
250 2 6313/C3 6313/C3 2-M63X1,5
Standard bearing type Cable entry
Type Pole D-end N-end mm
250 4,6,8 6314/C3 6313/C3 2-M63X1,5
280 2 6314/C3 6314/C3 2-M63X1,5
280 4,6,8 6317/C3 6314/C3 2-M63X1,5
315 2 6317/C3 6317/C3 2-M63X1,5
315 4,6,8,10 N319 6319/C3 2-M63X1,5
355 2 6319/C3 6319/C3 2-M63X1,5
355 4,6,8,10 N322 6322/C3 2-M63X1,5
Regreasable bearings available from size 160 (included)
Bearing seals :
radial seal up to frame size 225 (included) - axial seal from
250 to 355 (included)
The motors are normally tted with single-row deep groove
ball bearings as listed in the table below.
Terminal boxes are mounted on top of the motor. Theterminal box of motor sizes 71 to 132 can be turned 4 x
90 and in motor sizes 160 to 355 rotated 2 x 180 degree.
Protection of the standard terminal box is IP55. The motors
are supplied with 2 cable entries as standard according tothe table below.
Motors wounded for a given voltage at 50 Hz can be used
at 60 Hz without modication, considering recalculations
factors here under..
4
-
8/8/2019 Motors Iron
5/18
Motors or EU efciency levels
Output
kW
2 pole
Limit
EFF2/EFF3
2 pole
EFF1/EFF2
4 pole
Limit
EFF2/EFF3
EFF1/EFF2
1,1 76,2 82,8 76,2 83,8
1,5 78,5 84,1 78,5 85
2,2 81 85,6 81 86,4
3 82,6 86,7 82,6 87,4
4 84,2 87,6 84,2 88,3
5,5 85,7 88,6 85,7 89,2
7,5 87 89,5 87 90,111 88,4 90,5 88,4 91
15 89,4 91,3 89,4 91,8
18,5 90 91,8 90 92,2
22 90,5 92,2 90,5 92,6
30 91,4 92,9 91,4 93,2
37 92 93,3 92 93,6
45 92,5 93,7 92,5 93,9
55 93 94 93 94,2
75 93,6 94,6 93,6 94,7
90 93,9 95 93,9 95
EU efciency classes
T-T Electric have a motor range to meet or exceed the minimum efciencies stated in the highest level of the EU agreement of
LV motors.
These efciency levels apply to 2- and 4-pole, three phase squirrel cage induction motors, rated for 400 V, 50 Hz, with S1 duty
class with the output 1.1 to 90 kW which account for the largest volume on the market.
Three phase induction motors, 400 V 50 Hz T-T Electric motor efciency levels
2 pole
Output (kW)
100
95
90
85
80
75
Efficiency(%)
Output (kW)
100
95
90
85
80
75
Efficiency(%)
4 pole
EFF1 EFF1
EFF2 EFF2
EFF3EFF3
5
-
8/8/2019 Motors Iron
6/18
3000 r/min = 2 poles, 400V 50Hz
Output
kw
Type
designation
Speedn
r/min
Efciency
Full
load100%
3/4load
75%
Poweractor
cos
Current TorqueMoment
of inertie
inJ=GD2/4
kgm2
Weight
kg)
Sound
pressurelevel Lp
dB(A)InA
IsIn
TnNm
TsTn
TmaxTn
0,37 TAC-C 71A2 2780 70,0 68,0 0,82 0,9 6,1 1,3 2,2 2,2 0,0003 10 59
0,55 TAC-C 71B2 2785 73,0 72,4 0,82 1,3 6,1 1,9 2,2 2,2 0,00037 11 59
0,75 TAC-C 80A2 2840 75,0 75,5 0,85 1,7 6,1 2,5 2,2 2,2 0,00091 16 60
1,1 TAC-C 80B2 2855 78,0 77,9 0,85 2,4 7,0 3,7 2,2 2,2 0,00107 17 61
1,5 TAC-C 90S2 2850 79,0 79,0 0,87 3,2 7,0 5,0 2,2 2,2 0,00135 21 64
2,2 TAC-C 90L2 2850 81,5 81,8 0,86 4,5 7,0 7,4 2,2 2,2 0,00163 24 64
3 TAC-C 100L2 2860 83,0 83,2 0,88 5,9 7,0 10 2,2 2,2 0,00402 33 68
4 TAC-C 112M2 2900 85,0 84,6 0,90 7,6 7,0 13,2 2,2 2,2 0,00671 42 70
5,5 TAC-C 132SA2 2920 87,5 87,9 0,89 10,2 7,0 18 2,2 2,2 0,01241 58 73
7,5 TAC-C 132SB2 2920 88,5 90,1 0,90 13,6 7,0 24,5 2,2 2,2 0,01491 63 73
11 TAC-C 160MA2 2930 90,0 90,5 0,89 19,8 6,5 35,9 2,5 3,0 0,0436 112 75
15 TAC-C 160MB2 2920 90,0 90,1 0,89 27 6,5 49 2,5 3,2 0,0551 122 75
18,5 TAC-C 160L2 2930 90,5 90,9 0,90 32,8 6,5 60,3 2,5 3,2 0,06549 142 75
22 TAC-C 180M2 2940 90,8 91,0 0,90 38,9 6,5 71,5 2,3 2,8 0,08805 170 78
30 TAC-C 200LA2 2955 91,4 91,1 0,90 52,6 6,5 97 2,2 2,7 0,14821 235 84
37 TAC-C 200LB2 2955 92,2 91,8 0,90 64,4 6,5 120 2,3 2,7 0,16822 254 84
45 TAC-C 225M2 2970 92,6 92,2 0,89 78,8 7,0 145 2,5 2,8 0,29345 328 84
55 TAC-C 250M2 2960 93,4 91,7 0,89 96,5 7,5 178 2,4 3,0 0,3784 390 87
75 TAC-C 280S2 2972 94,0 92,3 0,90 128 7,5 241 2,5 3,3 0,587 504 88
90 TAC-C 280M2 2972 94,3 92,4 0,90 154 7,5 289 2,3 3,2 0,615 560 88
110 TAC-C 315S2 2980 94,0 92,2 0,91 187 7,1 353 1,8 2,2 1,4083 910 91
132 TAC-C 315M2 2980 94,5 93,0 0,91 223 7,1 423 1,8 2,2 1,5584 1010 91
160 TAC-C 315LA2 2979 94,6 93,5 0,92 267 7,2 513 1,8 2,2 1,7256 1070 91
200 TAC-C 315LB2 2978 94,8 94,0 0,92 332 7,2 641 1,8 2,2 1,9405 1120 91
250 TAC-C 355M2 2980 95,4 94,5 0,92 416 7,1 802 2,3 2,8 3,05 1438 92
315 TAC-C 355L2 2980 96,0 95,3 0,92 520 6,9 1011 2,0 2,8 3,6 1726 92
Technical Data H71-355 - 50 Hz
1500 r/min = 4 poles, 400V 50Hz
Output
kw
Type
designation
Speed
nr/min
Efcien-cy Full
load
100%
3/4
load75%
Power
actorcos
Current Torque Momentof inertie
inJ=GD2/4
kgm2
Weight
kg)
Sound
pressure
level Lp
dB(A)
In
A
Is
In
Tn
Nm
Ts
Tn
Tmax
Tn
0,25 TAC-C 71A4 1395 65,5 63,3 0,72 0,8 5,2 1,7 2,1 2,0 0,00053 11 46
0,37 TAC-C 71B4 1395 68,5 69,4 0,75 1,0 5,2 2,5 2,1 2,0 0,00066 11 48
0,55 TAC-C 80A4 1410 73,5 71,4 0,72 1,5 5,2 3,7 2,4 2,0 0,00145 16 49
0,75 TAC-C 80B4 1415 74,5 75,2 0,76 1,9 6,0 5,1 2,4 2,2 0,00174 17 49
1,1 TAC-C 90S4 1400 77,5 77,8 0,78 2,6 6,0 7,5 2,3 2,2 0,00254 21 55
1,5 TAC-C 90L4 1390 78,5 79,2 0,79 3,5 6,0 10,3 2,3 2,2 0,00317 25 55
2,2 TAC-C 100LA4 1430 81,5 82,3 0,81 4,9 a6,0 14,7 2,3 2,2 0,00679 32 56
3 TAC-C 100LB4 1420 82,8 82,5 0,83 6,3 6,5 20,2 2,3 2,2 0,00862 36 56
4 TAC-C 112M4 1430 85,0 84,6 0,82 8,3 6,5 26,7 2,3 2,2 0,01306 45 59
5,5 TAC-C 132S4 1430 86,0 87,1 0,85 10,9 6,5 36,7 2,3 2,2 0,02673 60 62
7,5 TAC-C 132M4 1440 88,5 88,3 0,85 14,4 6,5 49,7 2,3 2,2 0,03432 73 62
11 TAC-C 160M4 1460 89,5 90,0 0,85 20,9 6,5 72,0 2,4 2,8 0,06543 116 69
15 TAC-C 160L4 1460 90,0 90,4 0,86 28,0 6,5 98,1 2,3 2,4 0,09349 137 69
18,5 TAC-C 180M4 1470 91,0 90,9 0,86 34,1 6,5 120 2,3 3,0 0,16049 170 69
22 TAC-C 180L4 1470 92,0 90,0 0,88 39,4 6,5 143 2,4 3,0 0,18046 186 69
30 TAC-C 200L4 1470 92,2 91,8 0,88 53,4 6,5 195 2,2 2,8 0,2819 254 74
37 TAC-C 225S4 1480 92,6 91,2 0,85 67,9 7,0 239 2,2 2,8 0,37 308 76
45 TAC-C 225M4 1480 92,8 91,7 0,87 80,5 7,0 290 2,2 2,8 0,42 335 76
55 TAC-C 250M4 1480 93,4 91,3 0,87 98,5 7,0 355 2,4 3,0 0,78 450 79
75 TAC-C 280S4 1480 94,0 93,9 0,87 133 6,5 484 2,4 2,6 1,1 534 81
90 TAC-C 280M4 1480 94,3 94,6 0,87 159 7,2 581 2,3 2,8 1,35 592 81
110 TAC-C 315S4 1486 94,5 93,5 0,88 192 6,9 707 2,1 2,2 2,8596 930 83
132 TAC-C 315M4 1486 94,8 94,0 0,88 229 6,9 848 2,1 2,2 3,1848 1030 83
160 TAC-C 315LA4 1485 94,9 94,5 0,89 275 6,9 1029 2,1 2,2 3,6765 1050 89
200 TAC-C 315LB4 1485 95,0 94,2 0,89 343 6,9 1286 2,1 2,2 4,2516 1100 89
250 TAC-C 355M4 1490 95,3 94,5 0,90 421 6,9 1594 2,1 2,6 6,77 1546 90
315 TAC-C 355L4 1490 95,6 94,8 0,90 528 7,0 2008 2,1 2,3 8,2 1821 90
6
-
8/8/2019 Motors Iron
7/18
Technical Data H71-355 - 60 Hz
1800 r/min = 4 poles, 460V 60Hz
Output
kw
Type
designation
Speedn
r/min
Efciency
Full
load100%
Poweractor
cos
Current Torque Moment
of inertie
inJ=GD2/4
kgm2
Weight
kg)
Sound
pressurelevel Lp
dB(A)
In
A
Is
In
Tn
Nm
Ts
Tn
Tmax
Tn
0,29 TAC-C 71A4 1670 65,5 0,74 0,8 5,2 1,66 2,1 2,0 0,00053 11 46
0,43 TAC-C 71B4 1670 68,5 0,76 1,1 5,2 2,46 2,1 2,0 0,00066 11 48
0,63 TAC-C 80A4 1690 73,5 0,75 1,5 5,2 3,56 2,4 2,0 0,00145 16 49
0,86 TAC-C 80B4 1680 74,5 0,77 2,0 6,0 4,89 2,4 2,2 0,00174 17 49
1,27 TAC-C 90S4 1680 77,5 0,78 2,8 6,0 7,22 2,3 2,2 0,00254 21 55
1,73 TAC-C 90L4 1670 78,5 0,8 3,6 6,0 9,89 2,3 2,2 0,00317 25 55
2,53 TAC-C 100LA4 1720 81,5 0,82 5,0 6,0 14,05 2,3 2,2 0,00679 32 56
3,45 TAC-C 100LB4 1700 82,8 0,86 6,4 6,5 19,38 2,3 2,2 0,00862 36 56
4,6 TAC-C 112M4 1720 85,0 0,83 8,6 6,5 25,54 2,3 2,2 0,01306 45 59
6,33 TAC-C 132S4 1700 86,0 0,86 11,2 6,5 35,56 2,3 2,2 0,02673 60 62
8,6 TAC-C 132M4 1730 88,5 0,86 14,8 6,5 47,47 2,3 2,2 0,03432 73 62
12,7 TAC-C 160M4 1755 91,0 0,87 21,1 6,5 69,11 2,4 3,8 0,06543 116 69
17,3 TAC-C 160L4 1752 91,6 0,88 28,2 6,5 94,3 2,3 2,4 0,09349 137 69
21,3 TAC-C 180M4 1764 92,8 0,87 34,6 6,5 115,3 2,3 3,0 0,16049 170 69
25,3 TAC-C 180L4 1764 93,1 0,89 40,1 6,5 137 2,4 3,1 0,18046 186 69
34,5 TAC-C 200L4 1765 92,6 0,89 55,0 6,5 186,7 2,2 2,8 0,2819 254 74
42,6 TAC-C 225S4 1770 92,6 0,85 71,0 7,0 229,8 2,2 2,8 0,37 308 76
51,8 TAC-C 225M4 1770 92,8 0,88 83,2 7,0 279,5 2,2 2,8 0,42 335 76
63 TAC-C 250M4 1779 93,8 0,89 99,7 7,0 338,2 2,4 3,0 0,78 450 79
86 TAC-C 280S4 1775 94,0 0,88 136 6,5 462,7 2,4 2,6 1,1 534 81
104 TAC-C 280M4 1775 94,3 0,88 164 7,2 559,5 2,3 2,8 1,35 592 81
127 TAC-C 315S4 1783 95,0 0,89 189 6,9 680,2 2,1 2,2 2,8596 930 83152 TAC-C 315M4 1783 95,1 0,89 222 6,9 814,1 2,1 2,2 3,1848 1030 83
184 TAC-C 315LA4 1782 95,3 0,90 269 6,9 986,1 2,1 2,2 3,6765 1050 89
230 TAC-C 315LB4 1782 95,4 0,90 336 6,9 1232,6 2,1 2,2 4,2516 1100 89
287,5 TAC-C 355M4 1788 95,6 0,91 417 6,9 1538 2,0 2,5 6,77 1546 90
362,5 TAC-C 355L4 1788 95,8 0,91 525 7,0 1939 2,0 2,2 8,2 1821 90
3600 r/min = 2 poles, 460V 60Hz
Output
kw
Type
designation
Speedn
r/min
Efciency
Full
load
100%
Poweractor
cos
Current Torque Moment
of inertie
inJ=GD2/4
kgm2
Weight
kg)
Sound
pressure
level LpdB(A)
In
A
Is
In
Tn
Nm
Ts
Tn
Tmax
Tn
0,43 TAC-C 71A2 3340 70,0 0,83 1,0 6,1 1,2 2,2 2,2 0,0003 10 59
0,63 TAC-C 71B2 3340 73,0 0,84 1,4 6,1 1,8 2,2 2,2 0,00037 11 59
0,86 TAC-C 80A2 3410 75,0 0,88 1,7 6,1 2,4 2,2 2,2 0,00091 16 60
1,27 TAC-C 80B2 3430 78,0 0,88 2,4 7,0 3,5 2,2 2,2 0,00107 17 61
1,73 TAC-C 90S2 3420 79,0 0,87 3,3 7,0 4,8 2,2 2,2 0,00135 21 64
2,53 TAC-C 90L2 3440 81,5 0,86 4,7 7,0 7,0 2,2 2,2 0,00163 24 64
3,45 TAC-C 100L2 3430 83,0 0,89 6,1 7,0 9,6 2,2 2,2 0,00402 33 68
4,6 TAC-C 112M2 3480 85,0 0,91 7,9 7,0 12,6 2,2 2,2 0,00671 42 70
6,33 TAC-C 132SA2 3510 87,5 0,90 10,6 7,0 17,2 2,2 2,2 0,01241 58 73
8,6 TAC-C 132SB2 3510 88,5 0,91 14,0 7,0 23,4 2,2 2,2 0,01491 63 73
12,7 TAC-C 160MA2 3515 91,5 0,91 20,0 6,5 34,5 2,5 3,0 0,0436 112 75
17,3 TAC-C 160MB2 3517 91,6 0,91 27,2 6,5 47,0 2,5 3,2 0,0551 122 75
21,3 TAC-C 160L2 3520 91,8 0,91 33,5 6,5 57,8 2,5 3,2 0,06549 142 75
25,3 TAC-C 180M2 3528 92,1 0,90 40,1 6,5 68,5 2,3 2,8 0,08805 170 78
34,5 TAC-C 200LA2 3550 91,4 0,91 54,4 6,5 92,8 2,2 2,7 0,14821 235 8442,6 TAC-C 200LB2 3550 91,2 0,91 67,3 6,5 115 2,3 2,7 0,16822 254 84
51,8 TAC-C 225M2 3560 92,2 0,90 81,9 7,0 139 2,5 2,8 0,29345 328 84
63 TAC-C 250M2 3559 93,8 0,91 96,9 7,5 169 2,4 3,0 0,3784 390 87
86 TAC-C 280S2 3565 94,0 0,91 132 7,5 230 2,5 3,3 0,587 504 88
104 TAC-C 280M2 3565 94,3 0,91 159 7,5 279 2,3 3,2 0,615 560 88
127 TAC-C 315S2 3576 94,5 0,92 183 7,1 339 1,8 2,2 1,4083 910 91
152 TAC-C 315M2 3576 95,0 0,92 218 7,1 406 1,8 2,2 1,5584 1010 91
184 TAC-C 315LA2 3575 95,0 0,93 261 7,2 492 1,8 2,2 1,7256 1070 91
230 TAC-C 315LB2 3575 95,2 0,93 326 7,2 614 1,8 2,2 1,9405 1120 91
287,5 TAC-C 355M2 3576 95,7 0,92 412 7,1 769 2,2 2,7 3,05 1438 92
362,5 TAC-C 355L2 3576 96,2 0,92 517 6,9 970 1,9 2,7 3,6 1726 92
7
-
8/8/2019 Motors Iron
8/18
1000 r/min = 6 poles, 400V 50Hz
Output
kw
Type
designation
Speed
nr/min
EfciencyFull
load
100%
3/4
load75%
Power
actorcos
Current Torque Momentof inertie
inJ=GD2/4
kgm2
Weight
kg)
Sound
pressure
level Lp
dB(A)
InA
IsIn
TnNm
TsTn
TmaxTn
0,18 TAC-C 71A6 910 55,0 50,1 0,65 0,7 4,0 1,9 1,8 1,8 0,00056 10 45
0,25 TAC-C 71B6 890 60,0 58,3 0,65 0,9 4,0 2,7 1,8 1,8 0,00074 11 45
0,37 TAC-C 80A6 930 63,0 63,2 0,66 1,3 5,0 3,8 1,9 1,8 0,00159 17 48
0,55 TAC-C 80B6 925 65,0 65,1 0,68 1,8 5,0 5,7 1,9 1,8 0,00196 18 48
0,75 TAC-C 90S6 920 71,0 70,2 0,72 2,1 5,0 7,8 2,0 2,2 0,00292 21 51
1,1 TAC-C 90L6 920 73,0 73,1 0,74 2,9 5,0 11,4 2,0 2,2 0,00379 25 51
1,5 TAC-C 100L6 940 76,0 75,3 0,77 3,8 5,5 15,2 2,0 2,2 0,00999 32 54
2,2 TAC-C 112M6 940 80,0 81,2 0,76 5,2 5,5 22,4 2,0 2,2 0,01559 40 57
3 TAC-C 132S6 960 82,5 83,6 0,78 6,7 6,5 29,8 2,0 2,2 0,03116 55 59
4 TAC-C 132MA6 960 84,0 84,2 0,77 8,9 6,5 39,8 2,0 2,2 0,04074 65 59
5,5 TAC-C 132MB6 960 86,0 85,6 0,79 11,7 6,5 54,7 2,0 2,2 0,05332 75 59
7,5 TAC-C 160M6 970 88,0 85,3 0,78 15,8 6,0 73,8 2,0 2,3 0,09231 119 64
11 TAC-C 160L6 970 88,5 88,6 0,78 23 6,0 108 2,2 2,3 0,1297 140 65
15 TAC-C 180L6 980 89,0 89,1 0,82 29,7 6,0 146 2,3 2,8 0,2418 180 66
18,5 TAC-C 200LA6 980 90,3 90,2 0,82 36,1 6,0 180 2,2 2,8 0,34174 231 67
22 TAC-C 200LB6 980 90,4 90,3 0,83 42,3 6,0 214 2,1 2,8 0,46837 254 6730 TAC-C 225M6 980 90,8 89,2 0,78 61,1 6,6 292 2,2 2,8 0,62691 308 69
37 TAC-C 250M6 980 92,2 92,4 0,88 66,5 6,8 361 2,3 2,8 0,97 382 71
45 TAC-C 280S6 982 92,6 91,3 0,86 82 6,5 438 2,3 2,4 1,25 482 72
55 TAC-C 280M6 982 93,0 91,2 0,87 98,4 7,0 535 2,3 2,5 1,485 532 73
75 TAC-C 315S6 990 93,5 93,2 0,86 135 7,4 724 2,0 2,0 3,1942 920 78
90 TAC-C 315M6 990 93,8 91,9 0,86 162 7,4 868 2,0 2,0 3,723 1010 73
110 TAC-C 315LA6 990 94,3 93,5 0,87 194 6,8 1061 2,0 2,0 4,2564 1060 73
132 TAC-C 315LB6 990 94,5 93,8 0,87 232 6,8 1273 2,0 2,0 5,1577 1120 73
160 TAC-C 355MA6 990 94,7 93,9 0,89 274 6,8 1530 2,1 2,4 7,8 1360 78
200 TAC-C 355MB6 990 94,9 94,0 0,89 342 6,7 1913 2,0 2,3 9,1 1551 78
250 TAC-C 355L6 990 95,1 94,2 0,89 422 6,7 2391 2,0 2,4 11,4 2057 78
Technical Data H71-355 - 50 Hz
750 r/min = 8 poles, 400V 50Hz
Outputkw
Typedesignation
Speed
n
r/min
Efciency
Fullload
100%
3/4
load
75%
Power
actor
cos
Current Torque Moment
of inertie
inJ=GD2/4
kgm2
Weightkg)
Soundpressure
level Lp
dB(A)
In
A
Is
In
Tn
Nm
Ts
Tn
Tmax
Tn
0,18 TAC-C 80A8 700 51,0 50,1 0,6 0,9 3,3 2,46 1,8 1,9 0,00111 16 45
0,25 TAC-C 80B8 700 54,5 53,3 0,6 1,1 3,6 3,41 1,8 1,9 0,00326 17 45
0,37 TAC-C 90S8 700 62,5 62,1 0,61 1,4 4,4 5,05 1,8 1,9 0,00541 21 49
0,55 TAC-C 90L8 700 63,5 63,3 0,61 2,1 4,7 7,5 1,8 2,0 0,00756 24 49
0,75 TAC-C 100LA8 700 70,0 70,1 0,64 2,4 5,0 10,23 1,8 2,0 0,00971 31 56
1,1 TAC-C 100LB8 700 71,5 70,3 0,65 3,5 5,0 15,01 1,8 2,0 0,01186 34 56
1,5 TAC-C 112M8 700 75,0 75,4 0,68 4,3 5,0 20,46 1,8 2,0 0,1559 42 58
2,2 TAC-C 132S8 710 81,0 81,8 0,70 5,6 5,5 29,59 1,8 2,0 0,03625 56 583 TAC-C 132M8 710 81,0 81,4 0,75 7,1 5,5 40,35 1,8 2,0 0,04141 64 59
4 TAC-C 160MA8 720 84,0 84,0 0,73 9,4 5,5 53,06 2,1 2,5 0,0676 105 61
5,5 TAC-C 160MB8 720 85,5 85,6 0,74 12,6 5,5 72,95 2,1 2,5 0,09524 125 61
7,5 TAC-C 160L8 720 86,5 85,8 0,74 16,9 5,5 99,5 2,1 2,5 0,12122 142 61
11 TAC-C 180L8 730 87,7 87,0 0,77 23,5 5,4 143,9 2,0 2,8 0,23645 176 64
15 TAC-C 200L8 730 89,0 89,4 0,76 32,0 5,5 196,2 2,3 2,8 0,37103 235 66
18,5 TAC-C 225S8 740 90,0 89,1 0,75 39,6 5,5 238,8 2,1 2,8 0,53287 290 68
22 TAC-C 225M8 740 90,5 8,16 0,75 46,8 6,0 283,9 2,2 2,8 0,65825 302 68
30 TAC-C 250M8 740 91,3 90,1 0,79 60 6,5 387,2 2,3 2,6 0,975 392 70
37 TAC-C 280S8 740 91,8 91,7 0,79 74,2 6,0 477,5 2,1 2,6 1,25 488 71
45 TAC-C 280M8 740 92,4 91,1 0,79 89,5 6,0 580,7 2,1 2,7 1,485 548 71
55 TAC-C 315S8 740 92,8 91,5 0,82 105 6,9 709,8 1,8 2,0 3,6842 930 68
75 TAC-C 315M8 740 93,0 91,9 0,82 143 7,0 967,9 1,8 2,0 4,9591 1010 71
90 TAC-C 315LA8 740 93,8 93,2 0,82 170 7,1 1161,5 1,8 2,0 5,8205 1070 71
110 TAC-C 315LB8 740 94,0 92,4 0,82 204 6,4 1419,6 1,8 2,0 6,737 1140 71
132 TAC-C 355 MA8 745 93,7 93 0,82 248 6,4 1692,1 1,8 2,0 7,9 2000 78
160 TAC-C 355 MB8 745 94,4 94,1 0,82 299 6,4 2051 1,8 2,0 10,3 2150 78
200 TAC-C 355 L8 745 94,5 93,9 0;83 368 6,4 2563,4 1,8 2,0 12,3 2250 78
8
-
8/8/2019 Motors Iron
9/18
Technical Data H71-355 - 60 Hz
1200 r/min = 6 poles, 460V 60Hz
Outputkw
Typedesignation
Speed
n
r/min
Efciency
Fullload
100%
Power
actor
cos
Current Torque Moment
of inertie
inJ=GD2/4
kgm2
Weightkg)
Soundpressure
level Lp
dB(A)
InA
IsIn
TnNm
TsTn
TmaxTn
0,21 TAC-C 71A6 1090 55,0 0,66 0,8 4,0 1,8 1,8 1,8 0,00056 10 45
0,29 TAC-C 71B6 1070 60,0 0,66 1,0 4,0 2,6 1,8 1,8 0,00074 11 45
0,43 TAC-C 80A6 1101 63,0 0,67 1,3 5,0 3,7 1,9 1,9 0,00159 17 480,63 TAC-C 80B6 1101 65,0 0,68 1,9 5,0 5,5 1,9 1,9 0,00196 18 48
0,86 TAC-C 90S6 1105 71,0 0,73 2,2 5,0 7,4 2,0 2,2 0,00292 21 51
1,27 TAC-C 90L6 1100 73,0 0,75 3,0 5,0 11,0 2,0 2,2 0,00379 25 51
1,73 TAC-C 100L6 1130 76,0 0,77 3,9 5,5 14,6 2,0 2,2 0,00999 32 54
2,53 TAC-C 112M6 1145 80,0 0,77 5,4 5,5 21,1 2,0 2,2 0,01559 40 57
3,45 TAC-C 132S6 1150 82,5 0,79 7,0 6,5 28,7 2,0 2,2 0,03116 55 59
4,6 TAC-C 132MA6 1150 84,0 0,79 9,1 6,5 38,2 2,0 2,2 0,04074 65 59
6,33 TAC-C 132MB6 1150 86,0 0,80 12,1 6,5 52,6 2,0 2,2 0,05332 75 59
8,6 TAC-C 160M6 1167 88,0 0,79 16,2 6,0 70,4 2,0 2,3 0,09231 119 64
12,7 TAC-C 160L6 1166 89,9 0,80 23,2 6,0 104 2,2 2,3 0,1297 140 65
17,3 TAC-C 180L6 1176 91,1 0,83 30,0 6,0 141 2,3 2,8 0,2418 180 66
21,3 TAC-C 200LA6 1175 90,9 0,84 36,6 6,0 173 2,2 2,8 0,34174 231 67
25,3 TAC-C 200LB6 1175 90,0 0,85 43,4 6,0 206 2,1 2,8 0,46837 254 6734,5 TAC-C 225M6 1180 90,9 0,78 63,9 6,6 279 2,2 2,8 0,62691 308 69
42,6 TAC-C 250M6 1179 92,8 0,89 67,8 6,8 345 2,3 2,8 0,97 382 71
51,8 TAC-C 280S6 1175 92,6 0,87 84,4 6,5 421 2,3 2,4 1,25 482 72
63 TAC-C 280M6 1175 93,0 0,88 101 7,0 512 2,3 2,5 1,485 532 73
86 TAC-C 315S6 1188 93,8 0,87 132 7,4 691 2,0 2,0 3,1942 920 78
104 TAC-C 315M6 1188 94,0 0,87 160 7,4 836 2,0 2,0 3,723 1010 73
127 TAC-C 315LA6 1188 94,5 0,88 192 6,8 1021 2,0 2,0 4,2564 1060 73
152 TAC-C 315LB6 1188 95,0 0,88 228 6,8 1222 2,0 2,0 5,1577 1120 73
184 TAC-C 355MA6 1188 94,9 0,90 270 6,8 1481 2,0 2,3 7,8 1360 78
230 TAC-C 355MB6 1188 95,1 0,90 337 6,7 1852 1,9 2,2 9,1 1551 78
287,5 TAC-C 355L6 1188 95,3 0,90 421 6,7 2315 1,9 2,3 11,4 2057 78
900 r/min = 8 poles, 460V 60Hz
Output
kw
Type
designation
Speedn
r/min
Efciency
Full
load100%
Poweractor
cos
Current Torque Moment
of inertie
inJ=GD2/4
kgm2
Weight
kg)
Sound
pressurelevel Lp
dB(A)
In
A
Is
In
Tn
Nm
Ts
Tn
Tmax
Tn
0,21 TAC-C 80A8 820 53,8 0,54 0,9 3,3 2,5 1,8 1,9 0,00111 16 45
0,29 TAC-C 80B8 820 58,6 0,55 1,1 3,6 3,4 1,8 1,9 0,00326 17 45
0,43 TAC-C 90S8 830 61,7 0,56 1,6 4,4 5,0 1,8 1,9 0,00541 21 49
0,63 TAC-C 90L8 830 63,8 0,58 2,1 4,7 7,3 1,8 2,0 0,00756 24 49
0,86 TAC-C 100LA8 840 70,0 0,64 2,5 5,0 9,8 1,8 2,0 0,00971 31 56
1,27 TAC-C 100LB8 840 71,5 0,65 3,6 5,0 14,4 1,8 2,0 0,01186 34 56
1,73 TAC-C 112M8 850 75,0 0,69 4,4 5,0 19,4 1,8 2,0 0,1559 42 58
2,53 TAC-C 132S8 860 81,0 0,71 5,8 5,5 28,1 1,8 2,0 0,03625 56 583,45 TAC-C 132M8 860 81,0 0,77 7,3 5,5 38,3 1,8 2,0 0,04141 64 59
4,6 TAC-C 160MA8 865 88,0 0,76 9,0 5,5 50,8 2,1 2,5 0,0676 105 61
6,33 TAC-C 160MB8 866 85,9 0,76 12,7 5,5 69,8 2,1 2,5 0,09524 125 61
8,6 TAC-C 160L8 865 86,5 0,77 16,9 5,5 94,9 2,1 2,5 0,12122 142 61
12,7 TAC-C 180L8 876 86,0 0,78 24,9 5,4 139 2,0 2,8 0,23645 176 64
17,3 TAC-C 200L8 875 89,0 0,78 32,7 5,5 189 2,3 2,8 0,37103 235 66
21,3 TAC-C 225S8 890 90,0 0,75 41,4 5,5 229 2,1 2,8 0,53287 290 68
25,3 TAC-C 225M8 890 90,5 0,76 48,3 6,0 272 2,2 2,8 0,65825 302 68
34,5 TAC-C 250M8 891 92,1 0,80 61,5 6,5 370 2,3 2,6 0,975 392 70
42,6 TAC-C 280S8 885 91,8 0,80 76,1 6,0 460 2,1 2,6 1,25 488 71
51,8 TAC-C 280M8 885 92,4 0,80 92 6,0 559 2,1 2,7 1,485 548 71
63 TAC-C 315S8 888 93,2 0,83 102 6,9 678 1,8 2,0 3,6842 930 68
86 TAC-C 315M8 888 93,5 0,83 139 7,0 925 1,8 2,0 4,9591 1010 71104 TAC-C 315LA8 888 94,0 0,83 164 7,1 1119 1,8 2,0 5,8205 1070 71
127 TAC-C 315LB8 888 94,5 0,84 201 6,4 1366 1,8 2,0 6,737 1140 71
152 TAC-C 355 MA8 745 94 0,83 245 6,4 1948 1,8 2,0 7,9 2000 78
184 TAC-C 355 MB8 745 94,8 0,83 294 6,4 2359 1,8 2 10,3 2150 78
230 TAC-C 355 L8 745 94,9 0,84 362,1 6,4 2948 1,8 2 12,3 2250 78
9
-
8/8/2019 Motors Iron
10/18
Dimension drawing, H71-355, B3
Type
TAC-CPole A AA AB AC B BB C D E F G GD DB EG
71 2-6 112 24 150 136,5 90 108 45 14 j6 30 5 11 5 M5 12,5
80 2-8 125 35 165 155 100 130 50 19 j6 40 6 15,5 6 M6 16
90S 2-8 140 36 180 169 100 140 56 24 j6 50 8 20 7 M8 19
90L 2-8 140 36 180 169 125 165 56 24 j6 50 8 20 7 M8 19
100L 2-8 160 40 205 195 140 175 63 28 j6 60 8 24 7 M10 22
112M 2-8 190 45 230 217 140 180 70 28 j6 60 8 24 7 M10 22
132S 2-8 216 55 270 260 140 190 89 38 k6 80 10 33 8 M12 28
132M 2-8 216 55 270 260 178 230 89 38 k6 80 10 33 8 M12 28160M 2-8 254 65 320 314 210 260 108 42 k6 110 12 37 8 M16 36
160L 2-8 254 65 320 314 254 305 108 42 k6 110 12 37 8 M16 36
180M 2-4 279 70 355 352 241 315 121 48 k6 110 14 42,5 9 M16 36
180L 4-8 279 70 355 352 279 350 121 48 k6 110 14 42,5 9 M16 36
200L 2-8 318 70 395 395 305 370 133 55 m6 110 16 49 10 M20 39
225S 4-8 356 75 435 442 286 370 149 60 m6 140 18 53 11 M20 39
225M 2 356 75 435 442 311 395 149 55 m6 110 16 49 10 M20 39
225M 4-8 356 75 435 442 311 395 149 60 m6 140 18 53 11 M20 39
250M 2 406 80 490 480 349 445 168 60 m6 140 18 53 11 M20 39
250M 4-8 406 80 490 480 349 445 168 65 m6 140 18 58 11 M20 39
280S 2 457 85 550 535 368 490 190 65 m6 140 18 58 11 M20 39
280S 4-8 457 85 550 535 368 490 190 75 m6 140 20 67,5 12 M20 39
280M 2 457 85 550 535 419 540 190 65 m6 140 18 58 11 M20 39
280M 4-8 457 85 550 535 419 540 190 75 m6 140 20 67,5 12 M20 39
315S 2 508 120 635 620 406 570 216 65 M6 140 18 58 11 M20 42
315S 4-8 508 120 635 620 406 570 216 80 m6 170 22 71 14 M20 42
315M 2 508 120 635 620 457 680 216 65 m6 140 18 58 11 M20 42
315M 4-8 508 120 635 620 457 680 216 80 m6 170 22 71 14 M20 42
315L 2 508 120 635 620 508 680 216 65 m6 140 18 58 11 M20 42
315L 4-8 508 120 635 620 508 680 216 80 m6 170 22 71 14 M20 42
355M 2 610 120 730 710 560 750 254 75 m6 140 20 67.5 12 M20 42
355M 4-6 610 120 730 710 560 750 254 95 m6 170 25 86 16 M24 47
355L 2 610 120 730 710 630 750 254 75 m6 140 20 67.5 12 M20 42
355L 4-6 610 120 730 710 630 750 254 95 m6 170 25 86 16 M24 47
10
-
8/8/2019 Motors Iron
11/18
Dimension drawing, H71-355, B5-B35
Type
TAC-CPole H HA HD K L LD LA M N P S T
71 2-6 71 10 195 7 255 100 10 130 110 160 4-10 3,5
80 2-8 80 12 214 10 295 115 12 165 130 200 4-12 3,5
90S 2-8 90 12 250 10 320 125 12 165 130 200 4-12 3,5
90L 2-8 90 12 250 10 345 125 12 165 130 200 4-12 3,5
100L 2-8 100 14 270 12 385 143 13 215 180 250 4-15 4
112M 2-8 112 15 300 12 400 147 14 215 180 250 4-15 4
132S 2-8 132 18 345 12 470 182 14 265 230 300 4-15 4
132M 2-8 132 18 345 12 510 182 14 265 230 300 4-15 4160M 2-8 160 20 420 15 615 256 15 300 250 350 4-19 5
160L 2-8 160 20 420 15 670 256 15 300 250 350 4-19 5
180M 2-4 180 22 455 15 700 271 15 300 250 350 4-19 5
180L 4-8 180 22 455 15 740 271 15 300 250 350 4-19 5
200L 2-8 200 25 505 19 770 296 17 350 300 400 4-19 5
225S 4-8 225 28 555 19 815 329 20 400 350 450 8-19 5
225M 2 225 28 555 19 820 299 20 400 350 450 8-19 5
225M 4-8 225 28 555 19 845 329 20 400 350 450 8-19 5
250M 2 250 30 615 24 910 347 22 500 450 550 8-19 5
250M 4-8 250 30 615 24 910 347 22 500 450 550 8-19 5
280S 2 280 35 680 24 985 355 22 500 450 550 8-19 5
280S 4-8 280 35 680 24 985 355 22 500 450 550 8-19 5
280M 2 280 35 680 24 1035 355 22 500 450 550 8-19 5
280M 4-8 280 35 680 24 1035 355 22 500 450 550 8-19 5
315S 2 315 45 845 28 1190 397 22 600 550 660 8-24 6
315S 4-8 315 45 845 28 1220 427 22 600 550 660 8-24 6
315M 2 315 45 845 28 1300 397 22 600 550 660 8-24 6
315M 4-8 315 45 845 28 1330 427 22 600 550 660 8-24 6
315L 2 315 45 845 28 1300 397 22 600 550 660 8-24 6
315L 4-8 315 45 845 28 1330 427 22 600 550 660 8-24 6
355M 2 355 52 1010 28 1500 424 25 740 680 800 8-24 6
355M 4-6 355 52 1010 28 1530 454 25 740 680 800 8-24 6
355L 2 355 52 1010 28 1500 424 25 740 680 800 8-24 6
355L 4-6 355 52 1010 28 1530 454 25 740 680 800 8-24 6
11
-
8/8/2019 Motors Iron
12/18
Size P M N S TC105 105 85 70 M6 2,5
C120 120 100 80 M6 3
C140 140 115 95 M8 3
C140 140 115 95 M8 3
C160 160 130 110 M8 3,5
C160 160 130 110 M8 3,5
12
Dimension drawing, B14-B34
Type TAC-
C Pole A AA AB AC B BB C D E F G GD DB EG H HA HD K L LD AD
71 2-6 112 24 150 136,5 90 108 45 14 30 5 11 5 M5 12,5 71 10 195 7 255 100 120
80 2-8 125 35 165 155 100 130 50 19 40 6 15,5 6 M6 16 80 12 220 10 295 115 145
90S 2-8 140 36 180 169 100 140 56 24 50 8 20 7 M8 19 90 12 250 10 320 125 150
90L 2-8 140 36 180 169 125 165 56 24 50 8 20 7 M8 19 90 12 250 10 345 125 150
100L 2-8 160 40 205 195 140 175 63 28 60 8 24 7 M10 22 100 14 270 12 385 143 175
112M 2-8 190 45 230 217 140 180 70 28 60 8 24 7 M10 22 112 15 300 12 400 147 185
-
8/8/2019 Motors Iron
13/18
Power actor cos j
2 - 4 Poles 6 - 8 Poles
1.25 1.00 0.75 0.50 0.25 1.25 1.00 0.75 0.50 0.25xPn xPn xPn xPn xPn xPn xPn xPn xPn xPn
0.92 0.92 0.90 0.84 0.68 0.92 0.92 0.90 0.84 0.680.91 0.91 0.89 0.83 0.66 0.91 0.91 0.89 0.83 0.66
0.90 0.90 0.88 0.82 0.64 0.90 0.90 0.88 0.82 0.64
0.89 0.89 0.87 0.81 0.62 0.89 0.89 0.87 0.81 0.620.88 0.88 0.86 0.80 0.60 0.88 0.88 0.86 0.80 0.600.88 0.87 0.84 0.76 0.58 0.88 0.87 0.84 0.76 0.580.87 0.86 0.82 0.73 0.58 0.87 0.86 0.82 0.73 0.56
0.86 0.85 0.81 0.72 0.54 0.86 0.85 0.81 0.72 0.540.85 0.84 0.80 0.71 0.52 0.85 0.84 0.80 0.71 0.520.84 0.83 0.78 0.70 0.50 0.84 0.83 0.78 0.70 0.500.84 0.82 0.76 0.66 0.46 0.84 0.82 0.76 0.66 0.460.84 0.81 0.74 0.63 0.43 0.84 0.81 0.74 0.63 0.43
0.83 0.80 0.73 0.60 0.40 0.83 0.80 0.73 0.60 0.40
0.82 0.79 0.72 0.59 0.38 0.82 0.79 0.72 0.59 0.38
0.82 0.78 0.71 0.58 0.36 0.82 0.78 0.71 0.58 0.360.81 0.77 0.69 0.55 0.36 0.81 0.77 0.69 0.55 0.360.81 0.76 0.68 0.54 0.34 0.81 0.76 0.68 0.54 0.34
0.80 0.75 0.67 0.53 0.34 0.80 0.75 0.67 0.53 0.340.79 0.74 0.66 0.52 0.32 0.79 0.74 0.66 0.52 0.320.78 0.73 0.65 0.51 0.32 0.78 0.73 0.65 0.51 0.320.78 0.72 0.62 0.48 0.30 0.78 0.72 0.62 0.48 0.300.78 0.71 0.61 0.47 0.30 0.78 0.71 0.61 0.47 0.300.77 0.70 0.60 0.46 0.30 0.77 0.70 0.60 0.46 0.30
Efciency (%)
2 - 4 Poles 6 - 8 Poles
1.25 1.00 0.75 0.50 0.25 1.25 1.00 0.75 0.50 0.25
xPn xPn xPn xPn xPn xPn xPn xPn xPn xPn
97 97 97 96 92 97 97 97 95 92
96 96 96 95 91 96 96 96 94 91
95 95 95 94 90 95 95 95 93 9094 94 94 93 89 94 94 94 92 8993 93 93 92 88 93 93 93 91 8892 92 92 91 87 92 92 92 90 8691 91 91 90 86 91 91 91 89 85
89 90 90 89 85 90 90 90 88 8488 89 89 88 84 89 89 89 87 8387 88 88 87 83 88 88 88 86 8286 87 87 86 82 87 87 87 84 8086 86 86 85 80 86 86 86 83 78
83 85 86 85 79 85 85 85 82 7682 84 85 84 78 84 84 84 81 75
81 83 84 83 76 83 83 84 80 7480 82 83 82 74 81 82 82 78 7279 81 82 81 73 80 81 81 77 70
77 80 81 79 71 79 80 80 76 6876 79 80 78 69 78 79 80 75 6775 78 79 76 67 77 78 78 74 6674 77 78 75 65 76 77 77 73 6473 76 77 74 63 75 76 76 72 64
72 75 76 72 61 74 75 75 71 6271 74 75 71 60 73 74 74 70 6270 73 74 70 59 72 73 73 69 6069 72 73 69 57 70 72 71 67 5868 71 72 68 56 69 71 70 66 5667 70 71 67 54 68 70 69 65 56
13
EfciencyTypical efciency values are given for part load in the table here under.
Power actor valuesTypical power factor values for part load are given in the table above
-
8/8/2019 Motors Iron
14/18
Options Motor size
71 90 112 160 200
80 100 132 180 355
Balancing
Balancing to grade B (IEC60034-14) M M M M M
Bearings and lubrication
Roller bearing at D-en M M
Cold resistant grease M M M M M
Heat resistant grease M M M M M
Regreasable bearings NA NA NA M(160-250) S(280-355)
2RS bearing at both ends S S S S (160-250)
SPM nipples NA NA R M M
Agressive environment
Stainless steel/acid proof bolts M M M M M
Reinforced tropicalisation M M M M M
Terminal box
Terminal box right or left hand side view from D-end P P P P P
Cooling system
Unidirectional fan, clockwise seen from D-end R R R R R
Unidirectional fan, counter clockwise seen from D-end R R R R R
Aluminium fan R R R R R
Cooling method IC418(without fan) R R R R R
Separate motor cooling fan (fan axial, N-end) M M M M M
Drain holes
Modied drain hole position (for specied IM xxxx) M M M M M
Drain holes with plugs M M M M M
Earthing bolt
External earthing bolt M M M M M
Mounting arrangements
IM2101 foot/ange mounted, IEC ange, from IMI1001(B34 from B3) M(71-160) NA(180-355)
IM2001 foot/ange mounted, IEC ange,from IMI1001(B35 from B3) M M M M M
IM3601 ange mounted, IEC ange, from IMI3001(B14 fom B5) M(71-160) NA(180-355)
IM3001 ange mounted, IEC ange, from IMI3601(B5 from B14) M(71-160) NA(180-355)
Paint
Special paint colour, standard grade M M M M M
Stator winding temperature sensors
Bimetal detector, in stator winding M M M M M
PTC-thermister, in stator winding S S S S S
PT100 resistance element, in stator winding M M M M M
Shat & rotor
One or two special shaft extensions, std shaft material R(71-250) P(280-355)
Protection
Protective roof, vertical motor, shaft down M M M M M
IPW55 NA P(90-250) NA(280-355)
Degree of protection IP56 R R R R R
Heating element
Heating element, 200-240V M M M M M
Insulation system
Winding insulation class H R R R R R
Special winding insulation for frequency converter supply R R R R R
14
Options
-
8/8/2019 Motors Iron
15/18
Motor size 71 80 90 100 112 132 160
Stator Material Cast iron HT150GB/T9439
Paint colour Blue, Munsell 8B 4,5/3,25/NCS 4822 B05G
Paint thickness Two-pack 821 Acid Polyurethane Enamel, thickness >60 um
Bearing Material Cast iron HT150 GB/T9439
end Paint colour Blue, Munsell 8B 4,5/3,25/NCS 4822 B05G
shields Paint thickness Two-pack 821 Acid Polyurethane Enamel, thickness >60 um
D-end 2 pole 6202 6204 6205 6206 6206 6208 6309
Bearings 4 to 8 pole 2RSC3 2RSC3 2RSC3 2RSC3 2RSC3 2RSC3 2RSC3
N-end 2 pole 6202 6204 6205 6206 6206 6208 6209
4 to 8 pole 2RSC3 2RSC3 2RSC3 2RSC3 2RSC3 2RSC3 2RSC3
Axially-locked bearings Spring ring As standard, locked at D-end
Lubrication Greased for life
Rating plate Material Stainless steel
Terminal box Frame material Cast iron HT 150 GB/T9439
Cover material Cast iron HT 150 GB/T9439
Connections Cable entries 2-M16X1,5 2-M25X1,5 2-M25X1,5 2-M25X1,5 2-M32X1,5 2-M32X1,5 2-M40X1,5
1-M12x1,5 1-M12x1,5 1-M12x1,5 1-M16x1,5 1-M16x1,5 1-M16x1,5 1-M16x1,5
Terminals 6 terminals for connection
Fan Material Reinforced glass ber
Fan cover Material Steel
Paint colour Blue, Munsell 8B 4,5/3,25/NCS 4822 B05G
Paint thickness Two-pack 821 Acid Polyurethane Enamel, thickness >60 um
Stator winding Material Copper
Insulation insulation class F
Winding protection On request
Rotor winding Material Pressure die-cast aluminium
Balancing method Half key balancing as standard
Key ways Open key way
Enclosure IP 55
Cooling method IC 411
TAC-C cast iron motors basic design
15
-
8/8/2019 Motors Iron
16/18
TAC-C cast iron motors basic design
Motor size 180 200 225 250 280 315 355
Material Cast iron HT 150 GB/T9439 Cast iron HT200 GB/T9439
except vertical-mounted
Paint colour Blue, Munsell 8B 4,5/3,25 NCS 4822 B05G
Paint thickness Two-pack 821 Acid Polyurethane Lacquer
Enamel, thickness > 60 um
End shields Material Cast iron HT 150 GB/T9439 Cast iron HT200 GB/T9439except vertical-mounted
Paint colour Blue, Munsell 8B 4,5/3,25 NCS 4822 B05G
Paint thickness Two-pack 821 Acid Polyurethane Enamel
thickness > 60 um
Bearings D-end 2 pole 6211 2RSC3 6212 2RSC3 6312C3 6313C3 6314C3 6317C3 6319C3
4 to 8 pole 6311 2RSC3 6312 2RSC3 6313C3 6314C3 6317C3 N319 N322
N-end 2 pole 6211 6212 6312C3 6313C3 6314C3 6317C3 6319C3
4 to 8 pole 2RSC3 2RSC3 6312C3 6313C3 6314C3 6319C3 6322C3
Axially-locked Inner bearing cover
bearing As standard Locked at ND-end
Lubrication Greased for life or regreasable Regreasable bearings
Rating Material Stainless steel
Terminal box Frame material Cast iron HT 150 GB/T9439 Cast iron HT200 GB/T9439Cover material Cast iron HT 150 GB/T9439 Cast iron HT200 GB/T9439
Connections Cable entries 2-M40X1,5 2-M50X1,5 2-M50X1,5 2-M63X1,5 2-M63X1,5 2-M63X1,5 2-M63x1,5
1-M16X1,5 1-M16X1,5 1-M20X1,5 1-M20X1,5 1-M20X1,5 2-M20X1,5 1-M20x1,5
Terminals 6 terminals for connection
Fan Material Reinforced glass ber Reinforced glass ber or aluminium
Fan cover Material Steel
Paint colour Blue, Munsell 8B 4,5/3,25 NCS 4822 B05G
Paint thickness Two-pack 821 Acid Polyurethane Lacquer Enamel
thickness > 60 um
Stator Winding Material Copper
Insulation Insulation class F
Winding protection On request 3 PTC thermistors as standard
Rotor winding Material Pressure die-cast aluminium
Balancing method Half key balancing as standard
Key way Open key way
Enclosure IP 55
Cooling method IC 411
T-T Electric reserves the righ to change the design, technical specication and dimensions without prior notice.
16
-
8/8/2019 Motors Iron
17/1817
Mounting arrangements
Name plate
3~ motor TAC-C 90 L2 EFF 2
N 5011018
S1 IP 55Ins. CL F IEC 34-1
V Hz kW r/min A Cos
230 D 50 2,2 2850 7,85 0,86
260 D 60 2,53 3440 8,21 0,85
400Y 50 2,2 2850 4,53 0,85
3~ motor TAC-C 250 M4 EFF 2
N 5011019
S1 IP 55Ins. CL F IEC 34-1
V Hz kW r/min A Cos
400 D 50 5,5 1480 98,5 0,86
460 D 60 5,3 1779 99,70 0,89
690Y 50 5,05 1480 57,10 0,87
(H71 - 355) (H71 - 160) (H71 - 160) (H71 - 160) (H71 - 160) (H71 - 160)
(H71 - 280) (H71 - 355) (H71 - 160) (H71 - 355) (H71 - 160) (H71 - 160)
(H71 - 112) (H71 - 112) (H71 - 112) (H71 - 112) (H71 - 112) (H71 - 112)
Y Y
-
8/8/2019 Motors Iron
18/18
Founded over 100 years ago, T-T Electric is a world-class
supplier of top-quality industrial electric motors and
drives. Pioneers in the industry, we are an experienced
and established manufacturer of a comprehensive and
cost-effective range of highly reliable drive products. They
are used around the world in the toughest of applicationenvironments and in all industrial segments.
Driven by customer demand, T-T Electric is continually
researching product excellence and manufacturing
process perfection. The exible product design ensures
easy adaptations to customer requirements. This, combined
with unequalled short delivery times, make T-T Electric a
reference within industry. Our extensive support services
include diagnostics and maintenance on site as well as full
overhaul in our own repair facilities.
T-T Electric is committed to a working partnership with our
customers. For mutual benet, we focus on complete and
innovative solutions together.
France
T-T Electric
22 rue du 8 mai 1945
F-95340 PERSAN
Tel: +33 (0)1 30 28 62 01
Fax: +33 (0) 1 34 70 21 79
E-mail: info@t-telectric fr
Denmark
T-T Electric
Svendborgvej 83
5260 Odense S
Tel: +45 63 13 06 30
E-mail: [email protected]
UK
T-T Electric
Unit 7A Waterloo Park
Upper Brook Street
STOCKPORT SK1 3BP
Tel: +44 (0) 161 480 0037
Fax:+44 (0) 161 476 4390
E-mail: [email protected]
Germany
T-T Electric
Helgolandstrasse 67
D-70439 Stuttgart
Tel: +49 (0) 711 38 04 410
Fax: +49 (0) 711 38 04 411
E-mail: [email protected]
Sweden
Thrige Electric
Lefersgatan 1
PO Box 1641
S-75146 UppsalaTel: +46 (0) 18 657010
Fax: +46 (0) 18 107478
E-mail: [email protected]
t-telectric.com