nitoprime 25 constructive solutions2.imimg.com/data2/ng/qv/my-3845120/polyurea.pdfnitoprime ® 25...
TRANSCRIPT
Nito
prim
e® 2
5
constructive solutionsNitoprime® 25
Uses
Nitoprime 25 is suitable for priming concrete surfaces priorto the application of any of the Nitoflor SL2000/4000, TS / TFrange of resin based floor toppings, Nitocote range ofprotective coatings or Nitomortar range of epoxy repairmortars.
AdvantagesCan be applied even on damp surfaces
Improves the adhesion of epoxy floor toppings and mortarswith the substrate.
Description
Nitoprime 25 is a two component epoxy based primer withgood penetrating properties for concrete surfaces.
Technical support
Fosroc provides a countrywide technical advisory servicesupported by a team of specialists in the field.
Properties
200C 300C
Pot life 90 mins 30 mins
Application instructions
Surface preparation
Thorough surface preparation is vital. For best results Fosrocrecommends mechanical preparation techniques. (Forexample, mechanical scarifying, grit-blasting, sand blasting).For flooring and tanking works, care must be taken to ensurethat the substrate does not suffer from rising dampness. Ifsuch conditions exist, consult Fosroc.
New concrete floors
Should be at least 28 days old or have a moisturecontent ofless than 5% before proceeding with epoxy application.Laitance and deposits on new concrete floors are bestremoved by light grit blasting, mechanical scabbling orgrinding. On smaller areas thorough etching usingReebaklens may be considered. After etching the floor, itshould be thoroughly washed with clean water and thenallowed to dry.
Old concrete floors
Again, mechanical cleaning methods are stronglyrecommended on old concrete floors, particularly where heavycontamination by oil and grease has occurred or existingcoatings are present. These may well have been absorbedseveral millimeters deep into the concrete. To ensure goodadhesion all contamination should be removed and thesurface thoroughly cleaned of all dust and loose debris. Athorough detergent wash is also recommended followed bythorough cleaning with clean water and mopping it off to a drystate.
Mixing
Add the entire contents of the hardener tin to the base andmix thoroughly for 3 mins. until homogeneous, using a slowspeed drill ( 400 - 500 rpm) fitted with a suitable mixing paddle.
Application
Once mixed the primer should be applied immediately in athin continuous film to the clean prepared surface. Work theprimer into the surface using a stiff brush or roller. Excessapplication and puddling should be avoided. On poroussurfaces Nitoprime 25 will be absorbed very quickly leavingcharacteristic light coloured dry patches. it is recommendedthat a second priming coat be applied to these dry areas.This not only helps to ensure good adhesion but also preventsair release from the porous substrate which may causebubbles in the final epoxy topping later.
For Nitoflor SL2000 / 4000 applications, leave the Nitoprime25 to dry overnight. For Nitoflor TF, Nitomortar and Nitocote,allow the solvent in the Nitoprime 25 to evaporate and becometacky. the relevant datasheets may please be referred to, toensure this.
Limitations
Temperature limitations
Recommended application range is 100C - 400C. Fosrocshall be consulted where application or service is outside therange of 50C to 400C.
Estimating
Packaging and coverage
Nitoprime 25 is available in 1 and 4 litre packs.
Coverage
Approximate coverage rate 5.5 - 6.5 m2/ltr
Epoxy resin based primer for concrete surfaces
Nitoprime® 25
INDIA/0501/D
Important note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request. WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by it.
telephone fax e-mail
++91 80-2334 3188 ++91 80-2334 3178 [email protected]
Fosroc Chemicals (India) Pvt. Ltd.Head Office‘Vishnu Chittam’, No. 10, 2nd FloorSirur Park B Street, SeshadripuramBangalore 560020www.fosroc.com
® Denotes the trademark of Fosroc International Limited
Regional OfficesBangalore Mumbai Delhi Kolkata‘Vishnu Chittam’, No.10, 1stFloor 208/209, Persepolis 109-113, 1st Floor, Vikrant Towers P-569, Lake Terrace Extn.Sirur Park B Street, Seshadripuram Sector 17, Vashi 4, Rajendra Place First FloorBangalore 560 020 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 029Ph:080-2334 3188 Ph:022-2789 6411/12 Ph:011- 45062000-5 Ph: 033 24650917 / 55343188Fax : 080-23368667 Fax: 022 - 2789 6413 Fax: 011- 45062001 Fax: 033-24650891email: [email protected] email:[email protected] email:[email protected] email:[email protected]
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176 Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966 Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339 Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
Storage
Nitoprime 25 has a shelf life of 12 months when stored inunopened containers under normal warehouse conditions.
Precautions
Health & Safety instructions
Nitoprime 25 should not come into contact with skin andeyes or be swallowed. Avoid prolonged inhalation of solventvapours.
Some people are sensitive to epoxy resins, hardeners andsolvents. Gloves, goggles and barrier creams shouldtherefore be used while handling the product. Adequateventilation should be ensured and if working is enclosedareas, suitable breathing apparatus must be used. If theresin comes in contact with skin, it must be removed beforeit hardens with a resin removing cream, followed by washingwith soap and water - solvent should not be used.
Nitoflor Sol should be washed from skin immediately withsoap and water. Should accidental eye contamination occurwith any of the above products, it should be washed well withplenty of water and medical advice should be sought. Ifswallowed medical attention should be sought immediately.Vomiting should not be induced.
Cleaning
All tools and equipments should be cleaned with Nitoflor Solimmediately after use. Spillages should be absorbed withsand or sawdust and disposed off in accordance with localregulations.
Fire
Nitoflor Sol, Nitoprime 25 are flammable. Do not expose tonaked flames or other sources of ignition. Do not smokewhile handling the materials. Containers should be tightlysealed when not in use. In the event of fire, extinguish withCO2 or foam type extinguishers.
removing cream, followed by washing with soap and water -solvent should not be used.
Nitoflor Sol should be washed from skin immediately withsoap and water. Should accidental eye contamination occurwith any of the above products, it should be washed well withplenty of water and medical advice should be sought. Ifswallowed medical attention should be sought immediately.Vomiting should not be induced.
Flash Point
Nitoflor Sol 330CNitoprime 25 250C
Additional Information
In addition, the Nitoflor range of industrial flooring productsinclude concrete hardeners, resin floor coatings, toppingsand screeds designed to meet most requirements of modernindustrial environments. For further information contact thelocal Fosroc office.
Nito
prim
e® 2
5(M
)
constructive solutionsNitoprime® 25(M)
Epoxy resin based primer for concrete surfaces.
Uses
It is suitable for priming concrete surfaces prior to theapplication of any of the Nitoflor SL and TF range of resinbased floor toppings, Nitocote range of protective coatings orNitomortar epoxy repair mortars.
Advantages
Improves the adhesion of epoxy floor toppings and epoxymortars with the substrate.
Description
Nitoprime 25(M) is a two component epoxy based primerwith good penetrating properties for concrete surfaces.
Technical support
Fosroc provides a countrywide technical advisory servicesupported by a team of specialists in the field.
Properties
@ 200C @ 350C
Pot Life 4 hrs. 1 1/2 hrs.
Cure 4-6 hrs. 2-4 hrs.
Time between coats 4-6 hrs. 3-5 hrs.
Initial hardness 24 hrs. 18 hrs.
Full Cure 7 days 5 days
Below 200C, above mentioned times will increase
Application instructions
Surface preparation
Thorough surface preparation is vital. For best results Fosrocrecommends mechanical preparation techniques. (Forexample, mechanical scarifying, grit-blasting, sand blasting).
For flooring and tanking works, care must be taken to ensurethat the substrate does not suffer from rising dampness. Ifsuch conditions exist, consult Fosroc.
New concrete floors
Should be at least 28 days old or have a moisture content ofless than 5% before proceeding with epoxy application.Laitance and deposits on new concrete floors are bestremoved by light grit blasting, mechanical scabbling orgrinding. On smaller areas thorough etching usingReebaklens may be considered. After etching the floor, itshould be thoroughly washed with clean water and thenallowed to dry.
Old concrete floors
Again, mechanical cleaning methods are stronglyrecommended on old concrete floors, particularly where heavycontamination by oil and grease has occurred or existingcoatings are present. These may well have been absorbedseveral millimeters deep into the concrete. To ensure goodadhesion all contamination should be removed and thesurface thoroughly cleaned of all dust and loose debris. Athorough detergent wash is also recommended followed bycleaning with water and mopping it off to a dry state.
Mixing
Add the entire contents of the hardener tin to the base andmix thoroughly for 3 min. until homogeneous, using a slowspeed drill (400 - 500 rpm) fitted with a suitable mixing paddle.
Application
Once mixed the primer should be applied immediately in athin continuous film to the clean prepared surface. Work theprimer into the surface using a stiff brush or roller. Excessapplication and puddling should be avoided. On poroussurfaces Nitoprime 25(M) will be absorbed very quickly leavingcharacteristic coloured dry patches. it is recommended thata second priming coat be applied to these dry areas. Thisnot only helps to ensure good adhesion but also prevents airrelease from the porous substrate which may cause bubblesin the final epoxy topping later.
For Nitoflor SL applications, leave the Nitoprime 25(M) to dryovernight. For Nitoflor TF, Nitomortar and Nitocote, allow thesolvent in the Nitoprime 25(M) to evaporate and become tacky.Please refer to the relevant datasheets to ensure this.
Limitations
Temperature limitations
Recommended application range is 10 0C - 400C. ConsultFosroc where application or service is outside the range of50C to 400C.
Estimating
Packaging and coverage
Nitoprime 25(M) is available in 1, 2.5 & 5 kg packs.
Coverage
Approximate coverage rate
Nitoprime 25(M) 6-8m2/kg
Nitoprime® 25(M)
INDIA/0505/A
Important note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request. WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by it.
telephone fax e-mail
++91 80-2334 3188 ++91 80-2334 3178 [email protected]
Fosroc Chemicals (India) Pvt. Ltd.Head Office‘Vishnu Chittam’, No. 10, 2nd FloorSirur Park B Street, SeshadripuramBangalore 560020www.fosroc.com
® Denotes the trademark of Fosroc International Limited
Regional OfficesBangalore Mumbai Delhi Kolkata‘Vishnu Chittam’, No.10, 1stFloor 208/209, Persepolis 109-113, 1st Floor, Vikrant Towers P-569, Lake Terrace Extn.Sirur Park B Street, Seshadripuram Sector 17, Vashi 4, Rajendra Place First FloorBangalore 560 020 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 029Ph:080-23343188/ 2334 3182/3 Ph:022-2789 6412/14 Ph:011- 45062000 Ph: 033 24650917 / 55343188Fax : 080-23368667 Fax: 022 - 2789 6413 Fax: 011- 45062001 Fax: 033-24650891email: [email protected] email:[email protected] email:[email protected] email:[email protected]
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bhubaneshwar : (0674) 2521176 Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966 Goa : (0832) 2542465 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Hubli : (0836) 09343402597 Indore : (0731) 5049339/5061477 Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
Over vacuum dewatered floors finished with power trowels,after surface preparation, coverage of Nitoprime 25(M)maybe much more than the above value.
Storage
Nitoprime 25(M) has a shelf life of 12 months when storedin unopened containers under normal warehouseconditions.
Precautions
Health & Safety
Nitoprime 25(M) should not come into contact with skin andeyes or be swallowed. Avoid prolonged inhalation of solventvapours.
Some people are sensitive to epoxy resins, hardeners andsolvents. Gloves, goggles and barrier creams shouldtherefore be used while handling the product.
Adequate ventilation should be ensured and if working isenclosed areas, suitable breathing apparatus must be used.If the resin comes in contact with skin, it must be removedbefore it hardens with a resin removing cream, followed bywashing with soap and water - solvent should not be used.
Nitoflor Sol should be washed from skin immediately withsoap and water. Should accidental eye contamination occurwith any of the above products, it should be washed wellwith plenty of water and medical advice should be sought. Ifswallowed medical attention should be sought immediately.Vomiting should not be induced.
Cleaning
All tools and equipments should be cleaned with Nitoflor Solimmediately after use. Spillages should be absorbed withsand or sawdust and disposed off in accordance with localregulations.
Fire
Nitoflor Sol, Nitoprime 25(M) are flammable. Do not exposeto naked flames or other sources of ignition. Do not smokewhile handling the materials. Containers should be tightlysealed when not in use. In the event of fire, extinguish withCO2 or foam type extinguishers.
Flash point
Nitoflor Sol 33 0C
Nitoprime 25(M) 25 0C
Additional Information
In addition, the Nitoflor range of industrial flooring productsinclude concrete hardeners, resin floor coatings, toppingsand screeds designed to meet most requirements of modernindustrial environments. For further information contact thelocal Fosroc office.
Nito
prim
e® 3
3
constructive solutionsNitoprime® 33
High performance primer for the Cemtop range ofcementitious flooring materials
Uses
Nitoprime 33 is the recommended primer for the Cemtoprange of cementitious flooring when applied to concrete andcementitious screeds. The primer film forms and seals thesubstrate to prevent air release which could otherwise causepinholes in the floor topping. In addition it “wets” out thesubstrate, promotes adhesion and prevents desiccation ofthe Cemtop.
Advantages
Excellent adhesion to concrete and cementitious screeds
Excellent water resistance after film formation
Economic, easy to use with no restrictive pot life
Description
Nitoprime 33 is a water-based styrene-acrylate copolymeremulsion, formulated to achieve specific performancecharacteristics. It is supplied as a single component whiteliquid.
Technical Support
Fosroc offers a comprehensive range of high performance,high quality flooring, jointing and repair products for both newand existing floor surfaces. In addition, Fosroc offers atechnical support package to specifiers, end-users andcontractors, as well as on-site technical assistance inlocations all over the world.
Design Criteria
For the majority of applications in both the industrial andcommercial sectors, two coats of primer are recommended.If the floor is extremely porous, a third coat may be necessary.
Typical Properties
Typical values
Specific gravity : 1.02Solids content : 44-46%Drying time at 20°C : 2-4 hoursMaximum time betweencoats at 20°C : 24 hoursMaximum overlay timeat 20°C : 8 hoursMinimum applicationtemperature : 10°C
Specification Clause
The primer for the specified Cemtop cement based floortopping should be Nitoprime 33, a styrene-acrylate copolymeremulsion.
Application Instructions
CemtopThe installation of Cemtop is a specialist activity. The systemmust be applied by a Fosroc recommended contractor whohas been fully trained in the use of the materials, usingequipment supplied or approved by Fosroc.
Installation must not be attempted without reading the CemtopApplication Guide and the relevant product data sheet whichgive full details of the procedures for priming and applicationof the subsequent Cemtop overlay.
Nitoprime 33
The first primer application is carried out after the existingconcrete floor has been prepared and cleaned. Nitoprime 33is diluted in the ratio of 1:5 (primer to clean water by volume).It is applied and worked into the floor by broom. The primershould not be applied by roller or spray.
The second coat of primer should be diluted in the ratio of 1:3(primer to clean water by volume). It should be carried outwhen the first coat is dry. If the floor is porous, it may benecessary to prime a third time at a ratio of 1:3. The primermust be well brushed into the surface. Ponding of the primermust be avoided because this can lead to failure at the bondline.
During application the area must be well ventilated to speedthe drying of the primer. The application of Cemtop can proceedas soon as the primer has dried.
Cleaning
Nitoprime 33 should be removed from tools, equipment andmixers with clean water immediately after use. Dried materialcan only be removed mechanically.
Limitations
Nitoprime 33 is suitable for use on sound concrete andcementitious screeds that are free from surface contaminationand have been well prepared. It should not be used on oilcontaminated concrete or existing epoxy toppings. An epoxyprimer, Nitoprime 30, is suitable for these applications (consultseparate data sheet). Please consult Fosroc for advice onthe suitability of other substrates.
Nitoprime® 33
INDIA/0506/A
Important note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request. WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by it.
telephone fax e-mail
++91 80-2334 3188 ++91 80-2334 3178 [email protected]
Fosroc Chemicals (India) Pvt. Ltd.Head Office‘Vishnu Chittam’, No. 10, 2nd FloorSirur Park B Street, SeshadripuramBangalore 560020www.fosroc.com
® Denotes the trademark of Fosroc International Limited
Regional OfficesBangalore Mumbai Delhi Kolkata‘Vishnu Chittam’, No.10, 1stFloor 208/209, Persepolis 109-113, 1st Floor, Vikrant Towers P-569, Lake Terrace Extn.Sirur Park B Street, Seshadripuram Sector 17, Vashi 4, Rajendra Place First FloorBangalore 560 020 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 029Ph:080-2334 3188 Ph:022-2789 6411/12 Ph:011- 45062000-5 Ph: 033 24650917 / 55343188Fax : 080-23368667 Fax: 022 - 2789 6413 Fax: 011- 45062001 Fax: 033-24650891email: [email protected] email:[email protected] email:[email protected] email:[email protected]
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176 Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966 Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339 Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
Nitoprime 33 and Cemtop should not be applied when thesurface temperature of the substrate is below 10°C, or likelyto fall below 10°C within 48 hours of application.
Estimating
Supply
Nitoprime 33 : I litreConcentrate
Coverage
Nitoprime 33 Concentrate: 50-60 m2/litre/coat (after dilutionwith clean water as specified).
The coverage figures are for guidance only. The actual ratedepends on the absorbency and surface roughness of thesubstrate.
Note: The primer must be well brushed out and pondingavoided as too thick a layer of cured primer may causedebonding
Note: In accordance with Commercial or Health & Safetyrequirements packaging detail may alter. Please contact yourlocal Fosroc office for detail.
Storage
Nitoprime 33 has a shelf life of 12 months if stored in theoriginal unopened container. Protect from frost and extremeheat.
Precautions
During use Nitoprime 33 should not come into contact withskin and eyes or be swallowed. Wear suitable gloves andeye/face protection. In case of contact with skin, wash wellwith soap and water. In case of contact with eyes, rinseimmediately with plenty of water and seek medical advice. Ifswallowed seek medical attention immediately - do notinduce vomiting.
Fire
Nitoprime 33 is non-flammable.
Nio
prim
e® X
G
constructive solutionsNitoprime® XG
Moisture insensitive epoxy primer for cementitioussubstrates
Uses
It is suitable for priming concrete surfaces prior to the applicationof any of the Nitoflor SL2000/4000 and TF range of resin basedfloor toppings, Nitocote range of protective coatings orNitomortar epoxy repair mortars.
Advantages
Can be applied even on damp moist surfaces
Improves the adhesion of epoxy floor toppings and epoxymortars with the substrate.
Description
Nitoprime XG is a two component epoxy based primer withgood penetrating properties for concrete surfaces.
Technical support
Fosroc provides a countrywide technical advisory servicesupported by a team of specialists in the field.
Properties
Nitoprime XG 200C 300C
Pot life 90 min. 45-50 min.
Temperature limitations Recommended application rangeis 100C - 400C. Consultlocal Fosroc office whereapplication is outside the rangeof 100C - 400C.
Application instructions
Surface preparation
For best results it is recommended to use Nitoprime XG onconcrete which is at least 7 days old, and prepared surface asper standard practice.
New concrete floors
Shall be at least 7 days old before proceeding with primerapplication. Laitance and deposits on new concrete floors arebest removed by light grit blasting, mechanical scabbling orgrinding. On smaller areas thorough etching usingReebaklens may be considered. After etching the floor, itshould be thoroughly washed with clean water.
Old concrete floors
Mechanical cleaning methods as described above are stronglyrecommended on old concrete floors, particularly where heavycontamination by oil and grease has occurred or existingcoatings are present. These may well have been absorbedseveral millimeters deep into the concrete. To ensure goodadhesion all contamination should be removed and the surfacethoroughly cleaned of all dust and loose debris. A thoroughdetergent wash is also recommended followed by thoroughcleaning with clean water.
Mixing
The base and hardener contents are to be transferred in to asuitable container and mixed thoroughly for 3 mins. untilhomogeneous, using a slow speed drill ( 400 - 500 rpm) fittedwith a suitable mixing paddle.
Application
Once mixed the primer should be applied immediately in a thincontinuous film to the clean prepared surface. Work the primerinto the surface using a stiff brush or roller. Excess applicationand puddling should be avoided. On porous surfacesNitoprime XG will be absorbed very quickly leaving characteristiclight coloured dry patches. It is recommended that a secondpriming coat be applied to these dry areas. This not only helpsto ensure good adhesion but also prevents air release fromthe porous substrate which may cause bubbles in the finalepoxy topping later.
For Nitoflor SL2000 / 4000 and Nitocote/Nitoflor coatingsapplications, leave the Nitoprime XG to dry overnight. ForNitoflor TF and Nitomortar, allow Nitoprime XG to becometacky.
Cleaning
All tools and equipments should be cleaned with waterimmediately after use. Spillages should be absorbed withsand or sawdust and disposed off in accordance with localregulations.
Limitations
Temperature limitations
Recommended application range is 10 0C - 400C. ConsultFosroc where application or service is outside the range of100C to 400C.
Nitoprime® XG
INDIA/0504/B
Important note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request. WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by it.
telephone fax e-mail
++91 80-2334 3188 ++91 80-2334 3178 [email protected]
Fosroc Chemicals (India) Pvt. Ltd.Head Office‘Vishnu Chittam’, No. 10, 2nd FloorSirur Park B Street, SeshadripuramBangalore 560020www.fosroc.com
® Denotes the trademark of Fosroc International Limited
Regional OfficesBangalore Mumbai Delhi Kolkata‘Vishnu Chittam’, No.10, 1stFloor 208/209, Persepolis 109-113, 1st Floor, Vikrant Towers P-569, Lake Terrace Extn.Sirur Park B Street, Seshadripuram Sector 17, Vashi 4, Rajendra Place First FloorBangalore 560 020 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 029Ph:080-2334 3188 Ph:022-2789 6411/12 Ph:011- 45062000-5 Ph: 033 24650917 / 55343188Fax : 080-23368667 Fax: 022 - 2789 6413 Fax: 011- 45062001 Fax: 033-24650891email: [email protected] email:[email protected] email:[email protected] email:[email protected]
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176 Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966 Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339 Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
Estimating
Packaging and coverage
Nitoprime XG is available in 1 litre pack.
Coverage
Approximatecoverage rate
Nitoprime XG 5.2 - 6.2 m2 /litre
The coverage depends on substrate conditions.
Over vacuum dewatered floors finished with power trowels,after surface preparation, coverage of Nitoprime XG mayexceed for the above values.
Storage
Nitoprime XG has a shelf life of 6 months when stored inunopened containers under normal warehouse conditions.
Precautions
Health & Safety
Nitoprime XG should not come into contact with skin and eyesor be swallowed. Avoid prolonged inhalation of solvent vapours.
Some people are sensitive to epoxy resins, hardeners andsolvents. Gloves, goggles and barrier creams should thereforebe used while handling the product. Adequate ventilationshould be ensured and if working is enclosed areas, suitablebreathing apparatus must be used. If the resin comes incontact with skin, it must be removed before it hardens with aresin removing cream, followed by washing with soap andwater - solvent should not be used.
Should accidental eye contamination occur with any of theabove products, it should be washed well with plenty of waterand medical advice should be sought. If swallowed medicalattention should be sought immediately. Vomiting should notbe induced.
Fire
Do not expose to naked flames or other sources of ignition. Donot smoke while handling the materials. Containers shouldbe tightly sealed when not in use. In the event of fire, extinguishwith CO2 or foam type extinguishers.
Traf
ficgu
ard®
UR
150
constructive solutionsTrafficguard® UR150
Hard wearing, skid resistant, flexible protection systemfor car park decks
Uses
Trafficguard UR150 is a polyurethane traffic deck systemdesigned to provide an added level of protection to, new andexisting, trafficked areas such as:
Car park decks
Car park ramps
Turning areas
Entrance/exit areas
Thoroughfares
Advantages
Flexible and bridges dynamic cracks
Suitable for all zones in a car park
Seamless and watertight
Rapid application, reliable and safe
UV resistant
Description
Trafficguard UR150 is a multi-layer deck protection systemcomprising a primer and flexible Top Coat. All componentsare applied in the liquid phase and react chemically to forma tough, flexible, waterproof protective surface.
Trafficguard UR150 is available in a range of standardcolours. Contact your local Fosroc office for full details.
Properties
Elongation(ASTM D412) : ca. 175%Tensile Strength(ASTM D412) : 8 N/mm2
Tear Resistance(ASTM D624) : 18 N/mm2
Shore A Hardness(ASTM D2240) : ca. 80Overcoating time at 35°C : 16 hours
Chemical Resistance
Trafficguard UR150 is resistant to a range of chemicalsincluding:
- Petrol, Engine Oil
- Diesel, Medium concentration acids
- Detergents etc.
For full details contact your local Fosroc office.
Instructions for use
Surface Preparation
New concrete surfaces should have reached 80% of theirintended physical properties - generally only achieved after aminimum curing period of 28 days. Existing concrete surfacesmust be prepared to provide a clean, sound substrate.
Surfaces should be clean and dry with open capillary, freefrom laitance, oil and grease, curing compounds or othersurface contaminants which may prevent full and properadhesion of the primer. All blowholes, and other surfaceundulations should be repaired using an appropriate Fosrocproduct.
Trafficguard® UR150
Application
Primer
Apply Trafficguard UR150 Primer to the prepared surface atan application rate in the range of 0.2 to 0.3 ltr/m2.
Whilst Trafficguard UR150 Primer is still wet, blind with AntiSlip Grain No. 3 at an estimated rate of between 0.6 - 1.2 kg/m2,leave to dry for 16 hours @ 35ºC. Prior to the removal of excessantislip grain ensure that the grains are firmly embedded inthe primer.
Top Coat
Apply Trafficguard UR150 Top Coat to the primed surface atan application rate in the range of 0.3 - 0.6 ltr/m² per coat. Forbest results the Trafficguard UR150 Top Coat should beapplied with a short haired lambswool roller.
Prior to trafficing allow the following cure periods:
Foot traffic : 24 hrs @ 25°C or 18 hrs @ 35°CVehicle traffic : 5 days @ 25°C or 72 hrs at 35°C
Traffic marking lines may be applied using suitable productfrom Fosroc after five days from time of application.
Cleaning
Tools and equipment should be cleaned immediately afteruse with Nitoflor Sol*.
Technical Support
Fosroc offers a comprehensive technical support service tospecifiers, end users and contractors. It is also able to offeron-site technical assistance, an AutoCAD facility and dedicatedspecification assistance in locations all over the world.
Estimating
SupplyTrafficguard UR150 Primer : 9 litre packsTrafficguard UR150 Top Coat : 18 litre packsAntislip Grains No. 3 : 20 kg bags
CoverageParking Throughfare Ramps
Primer 0.2 ltr/m² 0.25 ltr/² 0.3 ltr/m²Antislip Grain 3 0.6 kg/m² 0.9 kg/m² 1.2 kg/m²Top coat 0.3 ltr/m² 0.3 ltr/m² 0.45 ltr/m²(per coat - 2 coat application recommended)
Note: The above coverage rates are given for guidance onlyas actual quantities used will vary depending upon thenature of substrate and conditions on site. It is stronglyadvised that trials are conducted to establish coveragerates.
Storage
Shelf life
When stored in warehouse conditions at less than 25°C,Trafficguard UR150 will have a shelf life of 12 months.
Trafficguard® UR150
Limitations
Trafficguard UR150 should not be applied on to surfaceswhich are known to or likely to suffer from rising damp orhave a relative humidity greater than 75% as measured inaccordance with BS8203 Appendix A or byThermohygrometer.
In conditions of high relative humidity i.e. 85-90%, goodventilation conditions are essential. Substrate temperatureshould be atleast 3°C above dew point.
Do not proceed with application if precipitation is imminent,or temperatures are expected to drop below 7°C within 24hours of application.
High temperature working
It is suggested that, for temperatures above 35°C, the followingguidelines are adopted as good working practice:
(i) Store material in a cool (preferably temperature controlled)environment, avoiding exposure to direct sunlight.
(ii) Keep equipment cool, arranging shade protection ifnecessary. It is especially important to keep cool thosesurfaces of the equipment which will come in direct contactwith the material itself.
(iii) Try to eliminate application during the hottest times of theday.
(iv) Make sufficient material, plant and labour available toensure that the application is a continuous process.
Precautions
Health and safety
Trafficguard UR150 Primer and Nitoflor Sol should not comein contact with skin or eyes, nor should they be swallowed.Avoid inhalation of vapours and ensure adequate ventilation.
Some people are sensitive to resins, hardeners and solvents.Wear suitable protective clothing, gloves and eye/faceprotection. Barrier cream can provide additional skin protection.
Should accidental skin contact occur, remove immediately witha resin removing cream followed by washing with soap andwater - do not use solvent.
The use of goggles is recommended, in case of accidentaleye contamination, rinse immediately with plenty of water andseek medical advice.
If swallowed seek medical attention immediately - do notinduce vomiting.
Fire
Nitoflor Sol and Trafficguard UR150 Primer are flammable.Do not use near a naked flame.
Flash pointsNitoflor Sol : 33°CTrafficguard UR150 Primer : 59°C
Trafficguard® UR150
INDIA/0638/B
Important note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request. WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by it.
telephone fax e-mail
++91 80-2334 3188 ++91 80-2334 3178 [email protected]
Fosroc Chemicals (India) Pvt. Ltd.Head Office‘Vishnu Chittam’, No. 10, 2nd FloorSirur Park B Street, SeshadripuramBangalore 560020www.fosroc.com
® Denotes the trademark of Fosroc International Limited
Regional OfficesBangalore Mumbai Delhi Kolkata‘Vishnu Chittam’, No.10, 1stFloor 208/209, Persepolis 109-113, 1st Floor, Vikrant Towers P-569, Lake Terrace Extn.Sirur Park B Street, Seshadripuram Sector 17, Vashi 4, Rajendra Place First FloorBangalore 560 020 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 029Ph:080-2334 3188 Ph:022-2789 6411/12 Ph:011- 45062000-5 Ph: 033 24650917 / 55343188Fax : 080-23368667 Fax: 022 - 2789 6413 Fax: 011- 45062001 Fax: 033-24650891email: [email protected] email:[email protected] email:[email protected] email:[email protected]
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176 Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966 Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339 Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
Additional Information
Fosroc manufactures a wide range of complementaryproducts which include :
waterproofing membranes & waterstops
joint sealants & filler boards
cementitious & epoxy grouts
specialised flooring materials
Fosroc additionally offers a comprehensive package ofproducts specifically designed for the repair andrefurbishment of damaged concrete. Fosroc’s ‘SystematicApproach’ to concrete repair features the following :
hand-placed repair mortars
spray grade repair mortars
fluid micro-concretes
chemically resistant epoxy mortars
anti-carbonation/anti-chloride protective coatings
chemical and abrasion resistant coatings
For further information on any of the above, please consultyour local Fosroc office - as below.