oem-approved gse & tooling for cfm56 engines
TRANSCRIPT
1+1.562.906.9300 | www.agsecorp.com | [email protected]
OEM-APPROVED GSE & TOOLING FOR
CFM56 ENGINES
Shipping Stand for CFM56-7B Engines (used on Boeing 737NG Aircraft)
AGSE P/Ns: AM-2811-4800 (Shipping Cradle) & AM-2563-227 (Transportation Base)
Shipping Stand for CFM56-5A/-5B Engines (used on Airbus A320 Family Aircraft)AGSE P/Ns: AM-2718-C1 (Shipping Cradle) & AM-2563-227 (Transportation Base)
Low Pressure Turbine & Shaft Major Module 3 Shipping Container
(with cover removed)
AGSE P/N: AGSE-C049
Pedestal with Optional MountAGSE P/N: AGSE-T016
Pneumatic Tire DollyAGSE P/N: AM-1686
For decades, AGSE has been a global leader in the original design, development, and manufacture of qualified & recommended solutions for the handling of the CFM56 family of high-bypass turbofan engines:
Approved by CFM International, GE Aviation, or Safran Aircraft Engines!
• Shipping Stands• Engine Covers• Lifting Fixtures• Site Transport• Pedestals
• Shipping Containers
• Line, Hangar & Shop Maintenance Tooling
2+1.562.906.9300 | www.agsecorp.com | [email protected]
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
*AGSE Shipping Stands are designed and built in compliance with the specifications and requirements of the engine’s original equipment manufacturer (OEM). The customer is solely responsible for selecting the appropriate packaging based upon all information at his/her disposal, including the specific application, regulatory compliances, product compatibility, shipping requirements, and documentation issued by the Engine OEM. Any AGSE-referenced shipping information presented either in this product literature or other AGSE documentation is intended as general guidance only and should not be considered a complete set of shipping requirements that can alter, satisfy, or influence both regulatory and Engine OEM shipping requirements. The content found in AGSE marketing materials and other documentation is subject to change; AGSE accepts no liability for loss or damage resulting from changes, errors, omissions, or misinterpretations of these AGSE publications.
OEM-APPROVED FOR CFM56 ENGINES SHIPPING STANDS
• Air/Truck Transport or Storage for engine in QEC configuration (ready for installation)*
• Bootstrap Capable (with AGSE or alternate lifting devices) to support engine during removal/installation from/on aircraft
Our trusted & reliable Shipping Stands not only offer the lowest total cost of ownership, but superior functionality that
can benefit any airline, aircraft hangar, or engine shop:
• Tie-Down Rings on Transportation Base offer secure retainment for both engine & Shipping Stand
• Shock-Absorbing Mounts reduce vibrations during transport
SHIPPING STANDS BY PART NUMBER
PART NUMBER: AGSE ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
LOW PROFILE TO ENABLE HEIGHT-RESTRICTED
AIR SHIPMENT
CRADLE COLLAPSES TO REDUCE SHIPPING/
STORAGE VOLUME
OPTIONAL TRUCK SHIPPING MOUNTS
AVAILABLE
COMPATIBLE WITH OTHER AGSE EQUIPMENT: ACCOMMODATES OTHER SELECT
ENGINESENGINE SLINGS/ BOOTSTRAP SYSTEMS SITE TRANSPORT
AM-2811-4800 (Shipping Cradle) AM-2563-227 (Transportation Base)
CFM56-7B Boeing 737NG
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961† (Cradle Caster Kit)
AGSE-E207-G01† CFM56-7B Boeing 737NG
AM-2718-C1 (Shipping Cradle) AM-2563-227 (Transportation Base)
CFM56-5A/-5B Airbus A320 Family AGSE-L006† (Engine Sling)
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961† (Cradle Caster Kit)
AGSE-E208-G01† (Shipping Cradle)AM-2563-227 (Transportation Base)
CFM56-5A/-5B Airbus A320 Family
AGSE-E043† (Shipping Cradle)AM-2510R88† (Transportation Base)
CFM56-5A/-5B Airbus A320 Family PW2000
AM-2387 (Shipping Cradle)AM-2563-227 (Transportation Base)
CFM56-5C Airbus A340-200/-300
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)
AM-1802 (Shipping Cradle)AM-2563-227 (Transportation Base)
CFM56-3 Boeing 737 Classic
AGSE-L012-G01† (Engine Sling)AM-1916† (Manual Bootstrap System)
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961† (Cradle Caster Kit)
AGSE-E206-G01† CFM56-3 Boeing 737 Classic
= Available Feature
3+1.562.906.9300 | www.agsecorp.com | [email protected]
RAIL MOUNTED CRADLES Bootstrap Capable and compatible with other AGSE or third party Transportation Bases!
PART NUMBER: Stanley ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
COMPATIBLE WITH TRANSPORTATION BASES
CONTAINING RAIL SPACING OF:
INCLUDES:WORK
PLATFORMSSHOCK
MOUNTSFOLDING FORWARD
ENGINE MOUNTSSPECIALIZED ROLLER
SHOE ASSEMBLIES
111502† CFM56-5A/-5B Airbus A320 Family88", 224 cm
90", 229 cm
111602† CFM56-5C Airbus A340-200/-30088", 224 cm
90", 229 cm
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINES RAIL MOUNTED CRADLES,
ENGINE COVERS & SITE TRANSPORT
SITE TRANSPORTExceptional engine transport within a facility or between local sites!
PART NUMBER: AGSE DESCRIPTION ENGINE(S)
ACCOMMODATEDAIRCRAFT
APPLICATION(S)COMPATIBLE WITH
OTHER AGSE EQUIPMENTDISASSEMBLES/
FOLDSBOOTSTRAP
CAPABLEADJUSTABLE
HEIGHT MANUAL
MOVEMENT ONLY
OTHER ENGINES ACCOMMODATED
AM-1686 Pneumatic Tire Dolly
CFM56-7B Boeing 737NG AM-2811-4800 (Shipping Cradle)
CFM56-5A/-5B Airbus A320 Family AM-2718-C1 (Shipping Cradle)
CFM56-5C Airbus A340-200/-300 AM-2387 (Shipping Cradle)
CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)
AGSE-V094-G01† Low-Profile Shop Dolly
CFM56-7B Boeing 737NG
AM-2563-227 (Transportation Base)
CFM56-5A/-5B Airbus A320 Family
CFM56-5C Airbus A340-200/-300
CFM56-3 Boeing 737 Classic
AGSE-E058† Light Weight Breakdown Stand CFM56-7B Boeing 737NG
AGSE-E016-G01 Light Weight Breakdown Stand CFM56-3 Boeing 737 Classic
AM-1961† Cradle Caster Kit
CFM56-7B Boeing 737NG AM-2811-4800 (Shipping Cradle)
CFM56-5A/-5B Airbus A320 Family AM-2718-C1 (Shipping Cradle)
CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)
AGSE-T073† Inlet Cowl DollyCFM56-7B Boeing 737NG
CFM56-3 Boeing 737 Classic
AGSE-E092-G01† Inlet Cowl Dolly CFM56-7B Boeing 737NG
AM-2302N-100† Inlet Cowl Dolly CFM56-5C Airbus A340-200/-300 Trent 500, Trent 700
ENGINE COVERSDependable and lasting protection against dirt, water, and contamination!
PART NUMBER: Engine OEM ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
SHIPPING COVER TYPE(S):
BARE ENGINE QEC ENGINE REINFORCED WITH FITTED BAR
856A3700 CFM56-7B Boeing 737NG
856A2930 CFM56-5B Airbus A320 Family
856A2782 CFM56-5A Airbus A319 & A320
856A2330 CFM56-5C Airbus A340-200/-300
856A3505 CFM56-3 Boeing 737 Classic
856A3595 CFM56-3 Boeing 737 Classic
= Available Feature
4+1.562.906.9300 | www.agsecorp.com | [email protected]
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINES ENGINE SLINGS, PEDESTAL SETS &
BOOTSTRAP SYSTEMS
PEDESTAL SETSAnother ideal horizontal build-up solution that achieves ergonomically efficient engine centerline heights!
PART NUMBER: Engine OEMAGSE
ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
ENGINE MODULE(S) SUPPORTED BY PEDESTAL(S)
NUMBER OF PEDESTALS MAXIMUM LOAD CAPACITY ACHIEVES ENGINE
CENTERLINE HEIGHT(S)
856A1312
CFM56-7BCFM56-5A/-5BCFM56-5CCFM56-3
Boeing 737NGAirbus A320 FamilyAirbus A340-200/-300Boeing 737 Classic
Forward Full Engine 2 1,000 lbs, 454 kg (per set) 65.4”, 166 cm
Aft Full Engine 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
Forward Fan Module 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
Aft Fan Module 2 1,000 lbs, 454 kg (per set) 65.4”, 166 cm
High Pressure Compressor Case 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
Rear Low Pressure Turbine Frame 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
AGSE-T016-G071/-G09 CFM56-7B Boeing 737NG QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)6,000 lbs, 2,722 kg (Aft Pedestals, Set of 2)
60", 152 cm
AGSE-T016-G03 CFM56-5A/-5B Airbus A320 Family QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)4,000 lbs, 1,814 kg (Aft Pedestals, Set of 2)
69", 175 cm
AGSE-T016-G11 CFM56-5C Airbus A340-200/-300 QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)4,000 lbs, 1,814 kg (Aft Pedestals, Set of 2)
69", 175 cm
AGSE-T016-G06 CFM56-3 Boeing 737 Classic QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)2,700 lbs, 1,225 kg (Aft Pedestals, Set of 2)
56", 142 cm
AGSE-T025-G02 CFM56-5C Airbus A340-200/-300 QEC Engine 4
4,800 lbs, 2,177 kg (Forward Ring)4,000 lbs, 1,814 kg (Aft Pedestals, Set of 2)
58"–64", 147 cm–163 cm
AM-1953-100 CFM56-3 Boeing 737 Classic QEC Engine 4
4,800 lbs, 2,177 kg (Forward Ring)6,000 lbs, 2,722 kg (Aft Pedestals, Set of 2)
56", 142 cm
ENGINE SLINGSStable and versatile overhead support for horizontal build-up or engine transfer to or from Shipping Stands!
PART NUMBER: AGSE ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S) MAXIMUM LOAD CAPACITY COMPATIBLE WITH
AGSE SHIPPING CRADLESCENTER OF GRAVITY
ADJUSTMENT FEATUREACCOMMODATES OTHER
SELECT ENGINES
AM-2106
CFM56-7B Boeing 737NG 6,800 lbs, 3,084 kg
Hand Crank CF6, PW2000, PW4000, RB211
CFM56-5A Airbus A319, A320 6,900 lbs, 3,130 kg
CFM56-5B Airbus A320 Family 7,000 lbs, 3,175 kg
CFM56-5C A340-200/-300 7,500 lbs, 3,402 kg
CFM56-3 Boeing 737 Classic 5,750 lbs, 2,608 kg
AGSE-L006† CFM56-5A/-5B Airbus A320 Family 18,000 lbs, 8,165 kg AM-2718-C1 Lifting Shackle CF6
AGSE-L012-G01† CFM56-3 Boeing 737 Classic 16,000 lbs, 7,257 kg AM-1802 Lifting Shackle CF6, RB211
AGSE-L002† CFM56-3 Boeing 737 Classic 12,000 lbs, 5,443 kg Cable Sling Hook Point CF6, PW2000, PW4000
AM-1949 CFM56-3 Boeing 737 Classic 10,000 lbs, 4,536 kg Lifting Shackle
1Universal model accommodates multiple mounting adapters to achieve variable engine centerline height(s)
BOOTSTRAP SYSTEMS All-in-One Engine Sling and Adapter Kits for more convenient bootstrap operations!
PART NUMBER: AGSE DESCRIPTION ENGINE(S) ACCOMMODATED
AIRCRAFT APPLICATION(S)
MAXIMUM PROOF LOAD CAPACITY
COMPATIBLE WITH AGSE SHIPPING CRADLES KIT INCLUDES:
AM-1916 Manual Bootstrap System CFM56-3 Boeing 737 Classic
7,000 lbs, 3,175 kg (Forward Beam)2,000 lbs, 907 kg (Aft Beam)
AM-1802
• Forward & Aft Bootstrap Beam Assemblies • Bootstrap Adapters• Three (3) Wired Rope Hoists• Attaching Hardware • Reusable Shipping Container
5+1.562.906.9300 | www.agsecorp.com | [email protected]
MODULE SHIPPING CONTAINERS BY PART NUMBER
PART NUMBER: AGSE ENGINE MODULE(S) SUPPORTEDIN SHIPPING CONTAINER
ENGINES(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
REMOVABLE COVER
SHOCK MOUNTS/ ISOLATION SYSTEM
SUPPORTING FOAM INSERTS
AGSE-C011† (AGSE-C026) Fan Disk & Booster Major Module 1 CFM56-7B Boeing 737NG
AGSE-C012 #1 & #2 Bearing Support Module 2 CFM56-7B Boeing 737NG
AGSE-C021 Low Pressure Turbine Module 13 CFM56-7B Boeing 737NG
AGSE-C022 Low Pressure Turbine Shaft Module 14 CFM56-7B Boeing 737NG
AGSE-C023 Low Pressure Turbine Frame Module 15 CFM56-7B Boeing 737NG
AGSE-C024 Transfer Gearbox Module 16 CFM56-7B Boeing 737NG
AGSE-C025 Accessory Gearbox Module 17 CFM56-7B Boeing 737NG
AGSE-C027 Fan Blades CFM56-7B Boeing 737NGAGSE-C028† (AGSE-C049) Low Pressure Turbine & Shaft Major Module 3 CFM56-7B Boeing 737NG
AGSE-C034 Core Module CFM56-7B Boeing 737NG
AGSE-C013 Core Module CFM56-5A Airbus A319, A320AGSE-C049 (AM-2141) Low Pressure Turbine & Shaft Major Module 3 CFM56-5A Airbus A319, A320
AM-2132 Fan Disk & Booster Module 1 CFM56-5A Airbus A319, A320
AM-2133 #1 & #2 Bearing Support Module 2 CFM56-5A Airbus A319, A320
AM-2134 Low Pressure Turbine Major Module 13 CFM56-5A Airbus A319, A320
AM-2135 Low Pressure Turbine Shaft Module 14 CFM56-5A Airbus A319, A320
AM-2136 Low Pressure Turbine Frame Major Module 15 CFM56-5A Airbus A319, A320
AM-2137 Transfer Gearbox Module 16 CFM56-5A Airbus A319, A320
AM-2138 Accessory Gearbox Module 17 CFM56-5A Airbus A319, A320
AM-2139 Major Module 1 CFM56-5A Airbus A319, A320
AM-2140 Fan Blades CFM56-5A Airbus A319, A320
AGSE-C009 Fan Disk & Booster Module 1 CFM56-5B Airbus A320 Family
AGSE-C010 #1 & #2 Bearing Support Module 2 CFM56-5B Airbus A320 Family
AGSE-C013 Core Module CFM56-5B Airbus A320 Family
AGSE-C044 Low Pressure Turbine Module 13 CFM56-5B Airbus A320 Family
AGSE-C045 Low Pressure Turbine Shaft Module 14 CFM56-5B Airbus A320 Family
AGSE-C046 Low Pressure Turbine Frame Module 15 CFM56-5B Airbus A320 Family
AGSE-C047 Fan Disk & Booster Major Module 1 CFM56-5B Airbus A320 Family
AGSE-C048 Fan Blades CFM56-5B Airbus A320 Family
AGSE-C049 Low Pressure Turbine & Shaft Major Module 3 CFM56-5B Airbus A320 Family
AM-2137 Transfer Gearbox Module 16 CFM56-5B Airbus A320 Family
AM-2138 Accessory Gearbox Module 17 CFM56-5B Airbus A320 FamilyAGSE-C049 (AM-2528) Low Pressure Turbine & Shaft Major Module 3 CFM56-5C Airbus A340-200/-300
AGSE-C050 Core Major Module CFM56-5C Airbus A340-200/-300
AM-2137 Transfer Gearbox Module 16 CFM56-5C Airbus A340-200/-300
AM-2138 Accessory Gearbox Module 17 CFM56-5C Airbus A340-200/-300
AM-2519 Booster Module 1 CFM56-5C Airbus A340-200/-300
AM-2520 #1 & #2 Bearing Support Module 2 CFM56-5C Airbus A340-200/-300
AM-2521 Low Pressure Turbine Module 13 CFM56-5C Airbus A340-200/-300
AM-2522 Low Pressure Turbine Shaft Module 14 CFM56-5C Airbus A340-200/-300
AM-2523 Low Pressure Turbine Frame Module 15 CFM56-5C Airbus A340-200/-300
AM-2526 Fan Case Major Module 1 CFM56-5C Airbus A340-200/-300
AM-2527 Fan Blades CFM56-5C Airbus A340-200/-300
AGSE-C007 Fan Booster CFM56-3 Boeing 737 Classic
AGSE-C008 #1 & #2 Bearing Support Module 2 CFM56-3 Boeing 737 Classic
AGSE-C035 Fan Disk & Booster Module 1 CFM56-3 Boeing 737 Classic
AGSE-C036 Core Module CFM56-3 Boeing 737 Classic
AGSE-C037 Low Pressure Turbine & Shaft Major Module 3 CFM56-3 Boeing 737 Classic
AGSE-C038 Low Pressure Turbine Module 13 CFM56-3 Boeing 737 Classic
AGSE-C039 Low Pressure Turbine Shaft Module 14 CFM56-3 Boeing 737 Classic
AGSE-C040 Low Pressure Turbine Frame Module 15 CFM56-3 Boeing 737 Classic
AGSE-C041 Transfer Gearbox Module 16 CFM56-3 Boeing 737 Classic
AGSE-C042 Accessory Gearbox Module 17 CFM56-3 Boeing 737 Classic
AGSE-C043 Fan Blades CFM56-3 Boeing 737 ClassicApproved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINE MODULES SHIPPING CONTAINERS
Fully enclosed to shield major modules against contamination and damage during split engine transport!
= Available Feature
6+1.513.402.7246 | www.agsecorp.com | [email protected]
LINE MAINTENANCE TOOLINGPART
NUMBER: CFM INT'L
DESCRIPTION
856A2609 Jacking Block - Fuel Pump/MEC or HMU856A2668 Puller Adapters856A2682 Eddy Current Inspection Kit - Fan Blades856A2686 Hand Cranking Drive Socket856A2691 Removal Tool - Spacer Pliers856A2953 Guide Pins - Stator Alternator 856A2956 Assistance Tool - Ring Fan Assembly
856A2957 Tool Set - Assembly/Disassembly Lubrication Unit Scavenge Filter Housing
856A2958 Actuation Hose Assembly - VSV 856A2961 Installation/Removal Tool - AGB Oil & Magnetic Seal856A3074 Balance Weights Riveter - Booster856A3519 Three (3) Legs Handling Sling - AGB856A3525 Removal/Installation Cradle - AGB 856A3557 D-Seal Tool - Magnetic Plug Lube Unit856A3576 Removal/Installation Tool - AGB Seals (7B27A) 856A3583 Leak Test Oil Seals
856A3598 Removal/Installation Cradle - Fuel Pump & MEC Package
856A3604 Wrench - Horizontal Drive Shaft Nut 856A3617 Pusher/Puller - Lube Unit Magnetic Plug856A3708 Pusher/Puller - Radial Drive Shaft856A3709 Alignment Fixture - AGB856A3726 Protective Floor - Fan Inlet Case856A3728 Core Engine Sealing Plate & Lock856A3770 Fan Blade Plotting Software856A3771 Check Template - Fan Blade Leading Edge856A3778 Guide Pins - Rear Spinner856A3779 Platform Puller - Fan Blade856A3782 Removal Wrench - Fan Blade Retainer Ring856A4624 Scouring Fixture - Fan Case Abradable Strip856A4628 Blade Template (Inches)856A4637 Inspection Tool - Booster Spool Forward Flange856A4640 Inspection Tool - Fan Disk Lugs856A4646 Gauge - Fan Blade Rear Shank856A5564 Resurfacing Kit - Spherical End Tube Coupling856A5807 Spiral Stencil - Front ConeFAN & BOOSTER MODULE TOOLING856A2316 Torque Wrench - LPT Coupling Nut856A2555 Lifting Beam - Fan Frame 856A2625 Storage Stand - LP Module856A2644 Tool Lock - Fan Disk
856A2655 Installation/Removal Fixture - Radial Drive Shaft Housings
856A2663 Puller Adapter - Splitter Fairing856A2694 Installation Tool - Inner Housing856A3501 Alignment/Guide Fixture - Booster to LPT Shaft856A3504 Pusher/Puller Fixture856A3524 Drive Adapter Tool Set - Booster & LPT 856A3702 Removal/Installation Centering Sleeve - MM3856A3703 Countertorque Wrench Guide856A3704 Residual Torque Beam856A3723 Guiding & Pulling Fixture - Booster856A3724 Tool Set - Sighting Fan Disk Coupling Bolts856A3725 Torque/Loosen Wrench - Fan Disk856A3732 Handling Fixture - Booster Rotor/Stator
856A5684 Eddy Current Inspection Kit - Fan Disk Inside Diameter
856A5945 Alignment Master - LPT Shaft
#1 & #2 BEARING TOOLING PART
NUMBER: CFM INT'L
DESCRIPTION
856A2336 Puller - Forward Rotating Air/Oil Separator 856A2609 Jacking Block - Fuel Pump /MEC or HMU856A2626 Storage Stand - No.1 & No.2 Bearing856A2640 Holder - Oil Separator Duct856A2662 Tool Kit - Masters Air Nozzles 856A2667 Check Tool - Assembly/Disassembly Circular Runout856A2745 Thickness Gauge Tool - Phonic Wheel856A2923 Supporting Guide - No.1 Bearing856A3011 Plug Extractor856A3012 Puller - No.2 Bearing Inner Race (with Actuator)856A3013 Puller - No.1 Sensor Ring (with Actuator)856A3033 Fixture - No.1 Bearing Sleeve Nut Retaining856A3267 Adapter Test Rig - No.1 & No.2 Bearing Air Flow856A3323 Center Bushing - No.1 Ball Bearing 856A3489 Targets Tool Set - No.1 Bearing Air Impingement Checks856A3556 Axial Weight Loading - No.1 Bearing856A3570 Wrench - No.2 Bearing Inner Race Seal856A3571 Wrench - Forward Rotating Air/Oil Separator Nut 856A3572 Wrench - No.1 Bearing Inner Race Nut856A3628 Installation Tool - No.1 Bearing Inner Race856A3721 Lift & Turn Adapter Tool Set - No.1 & No.2 Bearing Support856A3722 Dummy - Fan Disk856A3736 Locating Template - Drain Tube & OilCORE MODULE TOOLING856A2812 Dolly Fixture - Torque HP856A2818 Dolly - Tool Seating Check Core HP856A2821 Lube Protective Washer - No.4 Bearing Retainer856A2822 Torque Fixture - No.4 Bearing Retainer 856A2868 Protector - Fan ShaftLOW PRESSURE TURBINE (LPT) MODULE TOOLING856A2568 Lifting Ring - Aft LPT Shaft856A2577 Locating Ring - No.5 Bearing Rollers856A2600 LPT Shaft Guide & Stop Tool Guide856A2618 Holding Fixture - Rotor/Stator856A2647 Transportation/Storage Stand - LPT Major Module856A2660 Measuring Gauge - LPT Axial Clearance856A2661 Puller - Aft Rotating Air/Oil Separator 856A2674 Protection Cover - LPT Shaft856A2676 Checking Gauge - LPT MO1B Clearance (7BE)856A2677 Installation/Removal Fixture - Removable Retaining Ring
856A2685 Puller Adapter - Oil Inlet Cover (Hydraulic or Manual Option)
856A2692 Eddy Current Inspection Kit - TRF856A2702 Pin Guide - No.5 Bearing
856A2710 Handling Fixture - LPT Major Module (also accommodates CFM56-5B engines)
856A2713 Build-Up Fixture - LPT Shaft Module to LPT Module856A2714 Hoist Fixture - LPT Module856A2722 Guide Pins - LPT Frame to LPT Case 856A2729 Handling/Turn Fixture - LPT Case856A2731 Support Sectors - LPT Shaft to LPT 856A2750 Fixture - Stage 1 through 4 LPT Blades856A2752 Restrain Hooks - Air Seal to LPT Disassembly856A2755 Tool Set - Seals to Cone Stub Shaft856A2756 Heater - LPT Shaft to Stub Shaft (110V or 220V Option)856A2759 Puller Seals Tool Set856A2760 Support Handle Ring - Cone Stub Shaft & Stage 3 Disk856A2764 Heater Set - LPT (110V or 220V Option)856A2766 Support Ring - Cone Stub Shaft856A2773 Support Spacers - LPT Rotor/Case 856A2789 Ring - Center Aft Rotating Air Seal856A2826 Holding Fixture - No.4 Bearing Inner Race Bolts
LPT MODULE TOOLING (CONTINUED)PART NUMBER:
AGSE CFM INT'L
DESCRIPTION
856A2943 Protection Sleeve - Rear Inner Rotating Air/Oil Seal 856A2968 Heating Tool - Center Vent Tube (110V or 220V Option)856A3062 Puller - Rear Rotating Air/Oil Seal 856A3100 Locating Pin - Center Vent Tube 856A3234 Protector - Aft Center Vent Tube856A3268 Wrench - Center Vent Tube Sleeve Nut856A3269 Wrench - No.5 Bearing Inner Race Nut856A3279 Pusher/Puller - LPT Disk Sleeves856A3308 Puller - No.4 Bearing Inner Race856A3315 Puller - Center Vent Tube 856A3385 Wrench - Stage 1 LPT Disk Bolts856A3392 Torque Nut Wrench - Aft Rotating Air/Oil Separator856A3419 Puller Adapter - Oil Inlet Cover 856A3432 Gauge - LPT Stub Shaft to LPT Shaft856A3443 Puller - No.5 Bearing Outer Race856A3483 Protective Ring - No.4 Bearing856A3484 Protective Ring - No.5 Bearing 856A3485 Protective Cap - LPT Shaft Thread856A3487 Protector - No.4 Ball Bearing856A3488 Holding Fixture - Sectors Support 856A3491 Counter Wrench - No.5 Bearing Support Nipple856A3492 Counter Wrench - No.5 Bearing Support Nipple Line856A3501 Alignment/Guide Fixture - Booster to LPT Shaft856A3748 Protection Cover - Stage 1 LPT Disk856A3749 Installation Tool Set - Stage 2 & 3 Strips856A3750 Centering Fixture - LPT Shaft Module
856A3751 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A3752 Removal Fixture - Stage 1-2-3 Outer Stationary Air Seal856A3755 Foolproof Installation Tool - Stage 1 LPT & Air Seal856A3756 Installation Fixture - Stage 2 Shield856A3757 Installation Fixture - Stage 3 Shield
856A3760 Assembly/Disassembly Fixture - Stage 2 LPT Nozzle Segments
856A3761 Installation Tool Set - Stage 2 LPT Outer Stationary Seal856A3762 Assembly/Disassembly Fixture - LPT Rotor/Stator
856A3763 Assembly/Disassembly Fixture - Stage 3 LPT Nozzle Segments
856A3764 Installation Tool Set - Stage 3 LPT Outer Stationary Air Seal
856A3766 Handling Fixture Support - LPT Rotor/Stator856A3767 Handling Fixture - LPT Rotor/Stator
856A3788 Installation Tool Set - Stage 2 & 3 LPT Outer Stationary Air Seal
856A3790 Pusher/Puller Fixture - Duct Rear856A3791 Machining Fixture Adjusting Sleeve - No.5 Bearing856A3792 Centering Fixture - LPT Shaft to LPT856A3793 Pusher/Puller Fixture - Center Vent Tube
856A3794 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A3795 Mobile Stand - LPT Module856A3799 Guide Pin - No.5 Bearing Support 856A5944 Alignment Fixture - LPT ShaftENGINE SHIPPING, LIFTING & STORAGEAM-2563-227 Transportation Base (Wide Fork)AM-2811-4800 Shipping Cradle
856A1312 Engine Handling Support (also accommodates CFM56-5B engines)
856A2627 Lifting Beam856A2645 Engine Variable CG Beam856A2651 Engine Support Pad856A3515 Extension Beam - Variable CG Lift Fixture856A3700 Fitted Bar Engine Shipping Cover856A3710 Lifting Beam (2,000 daN/4,400 lbs Capacity)
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-7B engines.
OEM-APPROVED FOR CFM56-7B ENGINE MODULES SELECT LINE, HANGAR &
SHOP MAINTENANCE TOOLING
High-Quality engine tooling for airlines, MRO shops, lessors, and OEM customers!
Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!
7+1.513.402.7246 | www.agsecorp.com | [email protected]
LINE MAINTENANCE TOOLINGPART NUMBER:
CFM INT'L DESCRIPTION
856A2320 Tool Set - Engine Sumps Relube
856A2501 Dual Purpose Ratchet Wrench - VBV Manual Control
856A2537 Mounting Pin Protector - Accessory Drive Major Module
856A2609 Jacking Block - Fuel Pump/MEC or HMU
856A2645 Engine Variable CG Beam
856A2655 Fixture - Radial Drive Shaft Housings Installation/Removal
856A2659 Filter Adapter - Dry Out
856A2663 Puller Adapter - Splitter Fairing
856A2664 Setting Gauge - VBV Doors
856A2673 Installation Tool - Enerseal Seal
856A2677 Installation/Removal Fixture - Removable Retaining Ring
856A2678 CFMI Software - Trim Balance
856A2680 Vibration Software - No.4 Bearing
856A2686 Hand Cranking Drive Socket
856A2689 Vibration Analyzer Kit
856A2707 Leak Test Tool Set - AGB
856A2717 Lock Adapter - Core Engine
856A2718 Tool Set - Manual Drive Shaft
856A2719 Removal/Installation Support Fixture - TGB
856A2727 Puller - Radial Drive Shaft
856A2737 Leak Test Tool Set - AGB
856A2754 Support Fixture - AGB
856A2794 Protector Set - Seal Fitting
856A2796 Safety Protector Handcranking Pad
856A2805 Turnbuckle - AGB/TGB
856A2809 Back-Up Filter Handle Removal
856A2930 QEC Engine Shipping Cover
856A2947 Fan Blade Contour Template
856A2948 Fan Blades Liner Patch Inflatable Pressure Tool (220V/50Hz)
856A2949 Fan Blade Leading Edge Template
856A2953 Guide Pins - Stator Alternator
856A3409 Guide Pins - Spinner Rear Cone
856A3471 Drive Spline Adapter Fuel Pump (US Configuration)
856A3492 Counter Wrench - No.5 Bearing Support Nipple Line
856A3519 Three (3) Legs Handling Sling - AGB
856A3576 Removal/Installation Tool - AGB Seals
856A3770 Fan Blade Mapping Program Software
856A5649 Fan Disk Mirror Inspection
856A5817 Check Fan Blade Shank
856A5931 Fan Disk Dovetail Slots Gauge
856A5942 Fan Disk Dovetail Slots Gauge
FAN REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2555 Lifting Beam - Fan Frame
856A3111 Trunnion Dolly - Fan Frame Module
FAN ASSEMBLY/DISASSEMBLY856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module
856A2310 Alignment Fixture - Booster to LPT Shaft
856A2311 Dummy Tube - LPT Rotor Shaft Forward End
856A2571 Guide Pins - No.1 & No.2 Bearing Support Module Installation
856A2625 Storage Stand - Fan & Booster Module
856A2626 Storage Stand - Module 2
856A2667 Check Assembly/Disassembly Tool - Circular Runout
856A2701 Protective Floor - Fan Inlet Case Turbine Frame
856A2720 Machining Fixture - Fan Case Abradable Strip
FAN ASSEMBLY/DISASSEMBLY (CONTINUED)PART NUMBER:
CFM INT'L DESCRIPTION
856A2753 Accessory Drive Dummy
856A2902 Dummy Fan Disk
856A2904 Handling Fixture - Booster Rotor/Stator Assembly
856A2906 Guide & Countertorque Wrench
856A2907 Machining Fixture - Abradable Strip Fan Casing
856A2951 Counterweight Tool
856A2986 Alignment Fixture - Guide Booster
856A3111 Trunnion Dolly - Fan Frame Module
856A3267 Test Rig Adapter - No.1 & No.2 Bearing Support Air Flow Check
856A3409 Guide Pins - Spinner Rear Cone
856A3510 Lift & Turn Adapter - Module 2
856A3515 Extension Beam - Variable CG Lift Fixture
856A3608 Axial Loading Fixture
856A5939 Tool - Fan Blade Tip Clearance
FAN & BOOSTER MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module
856A2310 Alignment Fixture - Booster to LPT Shaft
856A2318 Thermal Shield
856A2501 Dual Purpose Ratchet Wrench - VBV Manual Control
856A2625 Storage Stand - Fan & Booster Module
856A2627 Lifting Beam
856A2631 Storage Stand - Fan Blades
856A2632 Puller
856A2644 Holding Tool - Fan Disk
856A2663 Puller Adapter - Splitter Fairing
856A2701 Protective Floor - Fan Inlet Case Turbine Frame
856A2780 Handling Adapter
856A2903 Torque Adaptation Beam
856A2904 Handling Fixture - Booster Rotor/Stator Assembly
856A2905 Torque/Loosen Wrench - Fan Disk Coupler
856A2906 Guide & Countertorque Wrench
856A2946 Protective Ring - Fan Disk
856A2951 Counterweight Tool
856A3111 Trunnion Dolly - Fan Frame Module
856A3504 Pusher/Puller Fixture - Module 1 & Major Module 3
856A3515 Extension Beam - Variable CG Lift Fixture
856A3524 Drive Adapter Tool Set - Booster & LPT
856A3793 Pusher/Puller Fixture - Center Vent Tube
856A5939 Tool - Fan Blade Tip Clearance
NO.1 & NO.2 BEARING SUPPORT MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module 856A2310 Alignment Fixture - Booster to LPT Shaft 856A2316 Torque/Loosen Wrench - LPT Coupling Nut856A2571 Installation Guide Pins - No.1 & No.2 Bearing Support Module856A2616 Centering Sectors - Forward LPT Shaft856A2626 Storage Stand - Module 2856A2701 Protective Floor - Fan Inlet Case Turbine Frame856A2709 Forward Support Guide856A2780 Handling Adapter856A2902 Dummy Fan Disk856A2903 Torque Adaptation Beam856A2906 Guide & Countertorque Wrench856A2909 Guide Pins - No.1 & No.2 Bearing Tubes 856A3510 Lift & Turn Adapter - Module 2 856A3515 Extension Beam - Variable CG Lift Fixture
OEM-APPROVED FOR CFM56-5A/-5B/-5C ENGINE MODULES SELECT LINE, HANGAR &
SHOP MAINTENANCE TOOLING
Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!
Guaranteed deliveries and round-the-clock after-sales service!
More Select CFM56-5A/-5B/-5C Tooling on Page 8
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-5A/-5B/-5C engines.
8+1.513.402.7246 | www.agsecorp.com | [email protected]
CORE MODULE REMOVAL/INSTALLATIONPART NUMBER:
CFM INT'L DESCRIPTION
856A2812 Dolly Fixture - Torque HP
856A2818 Tool Seating Check Dolly - Core
856A2866 Protector - Fan Shaft
856A2946 Protective Ring - Fan Disk
856A2997 Seating Check Gauge - Core Module to IGB
HIGH PRESSURE TURBINE (HPT) TOOLING856A2821 Lubricant Shield (Protective Washer) - No.4 Bearing Retainer
856A2822 Torque Fixture - No.4 Bearing Retainer
LPT MODULE REMOVAL/INSTALLATION856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module
856A2310 Alignment Fixture - Booster to LPT Shaft
856A2316 Torque/Loosen Wrench - LPT Coupling Nut
856A2412 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A2600 Guide & Stop Tool - LPT Shaft
856A2618 Holding Fixture - Rotor/Stator
856A2627 Lifting Beam
856A2632 Puller
856A2647 Mobile Storage Stand - Horizontal Major Module 3
856A2661 Puller - Aft Rotating Air/Oil Separator
856A2668 Puller Adapter Kit
856A2685 Puller Adapter - Oil Inlet Cover
856A2710 Handling Fixture - LPT Major Module
856A2717 Lock Adapter - Core Engine
856A2780 Handling Adapter
856A2903 Torque Adaptation Beam
856A2906 Guide & Countertorque Wrench
856A2946 Protective Ring - Fan Disk
856A2950 Centering Fixture - LPT Shaft
856A2968 Heating Tool - Center Vent Tube (110V or 220V Option)
856A3234 Protective Cap - Center Vent Tube, Rear Extension Duct
856A3392 Torque Nut Wrench - Aft Rotating Air/Oil Separator
856A3419 Puller Adapter - Oil Inlet Cover & Major Module 3
856A3485 Protective Cap - LPT Shaft Thread
856A3487 Protector - No.4 Ball Bearing
856A3504 Pusher/Puller Fixture - Module 1 & Major Module 3
856A3524 Drive Adapter Tool Set - Booster & LPT
856A3793 Pusher/Puller Fixture - Center Vent Tube
856A3794 Holding Ring - Stage 1 Outer Stationary Seal & Turbine Shroud Support
856A5944 Alignment Fixture - LPT Shaft
856A5945 Alignment Master - LPT Shaft
LPT MODULE DISASSEMBLY/ASSEMBLY856A2349 Assembly/Disassembly & Storage Dolly - LPT Shaft
856A2412 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A2544 Trunnion Dolly - Turbine Frame Module
856A2567 Forward Lifting Eye - LPT Shaft
856A2568 Aft Lifting Eye - LPT Shaft
856A2577 Locating Ring - No.5 Bearing Rollers
856A2618 Holding Fixture - Rotor/Stator
856A2627 Lifting Beam
856A2646 Trunnion Dolly - Turbine Frame Maintenance Module
856A2647 Mobile Stand - Horizontal Major Module 3 Storage
856A2710 Handling Fixture - LPT Major Module
856A2712 Handling Segments - Turbine Frame Module
856A2713 Buildup Fixture - LPT Shaft to LPT Module
LPT MODULE DISASSEMBLY/ASSEMBLY (CONTINUED)PART NUMBER:
CFM INT'L DESCRIPTION
856A2714 Hoist Fixture - LPT Module
856A2715 Storage Stand - LPT Module
856A2716 Distribution Ring
856A2722 Guide Pins - Turbine Frame to LPT Case
856A2731 Support Sectors - LPT Shaft to LPT Module
856A2756 Heat Diffuser - LPT Shaft (without Heat Gun)
856A2758 Centering Fixture - LPT Shaft to LPT
856A2772 Puller - LPT Rear Frame/LPT Case
856A2943 Protection Sleeve - Rear Inner Rotating Air/Oil Seal
856A2950 Centering Fixture - LPT Shaft
856A3234 Protective Cap - Center Vent Tube, Rear Extension Duct
856A3247 Alignment Guide - LPT Rear Frame to LPT Shaft
856A3383 Alignment Fixture - LPT Rear Frame to LPT
856A3484 Protective Ring - No.5 Bearing
856A3485 Protective Cap - LPT Shaft Thread
856A3487 Protector - No.4 Ball Bearing
856A3488 Holding Fixture Support - LPT Shaft
856A3759 Handling Sectors - Turbine Frame Module
856A3791 Machining Fixture Adjusting Sleeve - No.5 Bearing
856A3792 Centering Fixture - LPT Shaft to LPT
856A3794 Holding Ring - Stage 1 Outer Stationary Seal & Turbine Shroud Support856A3795 Mobile Stand - LPT ModuleTURBINE FRAME MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2544 Trunnion Dolly - Turbine Frame Module
856A2627 Lifting Beam
856A2646 Trunnion Dolly - Turbine Frame Maintenance Module
856A2651 Engine Support Pad
856A2712 Handling Segments - Turbine Frame Module
856A2722 Guide Pins - Turbine Frame to LPT Case
856A2772 Puller - LPT Rear Frame/LPT Case
856A2773 Support Spacers - LPT Rotor/LPT Case
856A3234 Protective Cap - Center Vent Tube, Rear Extension Duct
856A3247 Alignment Guide - LPT Rear Frame to LPT Shaft 856A3383 Alignment Fixture - LPT Rear Frame to LPTINLET GEARBOX (IGB) & #3 BEARING MODULE REMOVAL/INSTALLATION856A2310 Alignment Fixture - Booster to LPT Shaft
856A2616 Centering Sectors - Forward LPT ShaftTRANSFER GEARBOX (TGB) MODULE REMOVAL/INSTALLATION856A2414 Fixture - Guide Radial Shaft
856A2537 Mounting Pin Protector - Accessory Drive Major Module
856A2632 Puller
856A2718 Tool Set - Manual Drive Shaft
856A2719 Remove/Install Support Fixture - TGB
856A2727 Puller - Radial Drive Shaft
856A2805 Turnbuckle - AGB/TGB
ACCESSORY GEARBOX (AGB) MODULE REMOVAL/INSTALLATION856A2537 Mounting Pin Protector - Accessory Drive Major Module
856A2609 Jacking Block - Fuel Pump/MEC or HMU
856A2632 Puller
856A2718 Tool Set - Manual Drive Shaft
856A2754 Support Fixture - AGB
856A2805 Turnbuckle - AGB/TGB
856A2953 Guide Pins - Stator Alternator
856A3519 Three (3) Legs Handling Sling - AGB
©2021 AGSE-Westmont Industries. All rights reserved. R.9.1.21
OEM-APPROVED FOR CFM56-5A/-5B/-5C ENGINE MODULES SELECT LINE, HANGAR &
SHOP MAINTENANCE TOOLING
Competitive pricing and expert consultation ensure an optimal Return on Investment!
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-5A/-5B/-5C engines.
Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!
1+1.562.906.9300 | www.agsecorp.com | [email protected]
OEM-APPROVED GSE & TOOLING FOR
CFM56 ENGINES
Shipping Stand for CFM56-7B Engines (used on Boeing 737NG Aircraft)
AGSE P/Ns: AM-2811-4800 (Shipping Cradle) & AM-2563-227 (Transportation Base)
Shipping Stand for CFM56-5A/-5B Engines (used on Airbus A320 Family Aircraft)AGSE P/Ns: AM-2718-C1 (Shipping Cradle) & AM-2563-227 (Transportation Base)
Low Pressure Turbine & Shaft Major Module 3 Shipping Container
(with cover removed)
AGSE P/N: AGSE-C049
Pedestal with Optional MountAGSE P/N: AGSE-T016
Pneumatic Tire DollyAGSE P/N: AM-1686
For decades, AGSE has been a global leader in the original design, development, and manufacture of qualified & recommended solutions for the handling of the CFM56 family of high-bypass turbofan engines:
Approved by CFM International, GE Aviation, or Safran Aircraft Engines!
• Shipping Stands• Engine Covers• Lifting Fixtures• Site Transport• Pedestals
• Shipping Containers
• Line, Hangar & Shop Maintenance Tooling
2+1.562.906.9300 | www.agsecorp.com | [email protected]
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINES SHIPPING STANDS
• Air/Truck Transport or Storage for engine in QEC configuration (ready for installation)*
• Bootstrap Capable (with AGSE or alternate lifting devices) to support engine during removal/installation from/on aircraft
Our trusted & reliable Shipping Stands not only offer the lowest total cost of ownership, but superior functionality that
can benefit any airline, aircraft hangar, or engine shop:
• Tie-Down Rings on Transportation Base offer secure retainment for both engine & Shipping Stand
• Shock-Absorbing Mounts reduce vibrations during transport
SHIPPING STANDS BY PART NUMBER
PART NUMBER: AGSE ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
LOW PROFILE TO ENABLE HEIGHT-RESTRICTED
AIR SHIPMENT
CRADLE COLLAPSES TO REDUCE SHIPPING/
STORAGE VOLUME
OPTIONAL TRUCK SHIPPING MOUNTS
AVAILABLE
COMPATIBLE WITH OTHER AGSE EQUIPMENT: ACCOMMODATES OTHER SELECT
ENGINESENGINE SLINGS/ BOOTSTRAP SYSTEMS SITE TRANSPORT
AM-2811-4800 (Shipping Cradle) AM-2563-227 (Transportation Base)
CFM56-7B Boeing 737NG
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961† (Cradle Caster Kit)
AGSE-E207-G01† CFM56-7B Boeing 737NG
AM-2718-C1 (Shipping Cradle) AM-2563-227 (Transportation Base)
CFM56-5A/-5B Airbus A320 Family AGSE-L006† (Engine Sling)
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961† (Cradle Caster Kit)
AGSE-E208-G01† (Shipping Cradle)AM-2563-227 (Transportation Base)
CFM56-5A/-5B Airbus A320 Family
AGSE-E043† (Shipping Cradle)AM-2510R88† (Transportation Base)
CFM56-5A/-5B Airbus A320 Family PW2000
AM-2387 (Shipping Cradle)AM-2563-227 (Transportation Base)
CFM56-5C Airbus A340-200/-300
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)
AM-1802 (Shipping Cradle)AM-2563-227 (Transportation Base)
CFM56-3 Boeing 737 Classic
AGSE-L012-G01† (Engine Sling)AM-1916† (Manual Bootstrap System)
AGSE-V094-G01† (Low-Profile Shop Dolly)AM-1686 (Pneumatic Tire Dolly)AM-1961† (Cradle Caster Kit)
AGSE-E206-G01† CFM56-3 Boeing 737 Classic
= Available Feature
*AGSE Shipping Stands are designed and built in compliance with the specifications and requirements of the engine’s original equipment manufacturer (OEM). The customer is solely responsible for selecting the appropriate packaging based upon all information at his/her disposal, including the specific application, regulatory compliances, product compatibility, shipping requirements, and documentation issued by the Engine OEM. Any AGSE-referenced shipping information presented either in this product literature or other AGSE documentation is intended as general guidance only and should not be considered a complete set of shipping requirements that can alter, satisfy, or influence both regulatory and Engine OEM shipping requirements. The content found in AGSE marketing materials and other documentation is subject to change; AGSE accepts no liability for loss or damage resulting from changes, errors, omissions, or misinterpretations of these AGSE publications.
3+1.562.906.9300 | www.agsecorp.com | [email protected]
RAIL MOUNTED CRADLES Bootstrap Capable and compatible with other AGSE or third party Transportation Bases!
PART NUMBER: Stanley ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
COMPATIBLE WITH TRANSPORTATION BASES
CONTAINING RAIL SPACING OF:
INCLUDES:WORK
PLATFORMSSHOCK
MOUNTSFOLDING FORWARD
ENGINE MOUNTSSPECIALIZED ROLLER
SHOE ASSEMBLIES
111502† CFM56-5A/-5B Airbus A320 Family88", 224 cm
90", 229 cm
111602† CFM56-5C Airbus A340-200/-30088", 224 cm
90", 229 cm
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINES RAIL MOUNTED CRADLES,
ENGINE COVERS & SITE TRANSPORT
SITE TRANSPORTExceptional engine transport within a facility or between local sites!
PART NUMBER: AGSE DESCRIPTION ENGINE(S)
ACCOMMODATEDAIRCRAFT
APPLICATION(S)COMPATIBLE WITH
OTHER AGSE EQUIPMENTDISASSEMBLES/
FOLDSBOOTSTRAP
CAPABLEADJUSTABLE
HEIGHT MANUAL
MOVEMENT ONLY
OTHER ENGINES ACCOMMODATED
AM-1686 Pneumatic Tire Dolly
CFM56-7B Boeing 737NG AM-2811-4800 (Shipping Cradle)
CFM56-5A/-5B Airbus A320 Family AM-2718-C1 (Shipping Cradle)
CFM56-5C Airbus A340-200/-300 AM-2387 (Shipping Cradle)
CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)
AGSE-V094-G01† Low-Profile Shop Dolly
CFM56-7B Boeing 737NG
AM-2563-227 (Transportation Base)
CFM56-5A/-5B Airbus A320 Family
CFM56-5C Airbus A340-200/-300
CFM56-3 Boeing 737 Classic
AGSE-E058† Light Weight Breakdown Stand CFM56-7B Boeing 737NG
AGSE-E016-G01 Light Weight Breakdown Stand CFM56-3 Boeing 737 Classic
AM-1961† Cradle Caster Kit
CFM56-7B Boeing 737NG AM-2811-4800 (Shipping Cradle)
CFM56-5A/-5B Airbus A320 Family AM-2718-C1 (Shipping Cradle)
CFM56-3 Boeing 737 Classic AM-1802 (Shipping Cradle)
AGSE-T073† Inlet Cowl DollyCFM56-7B Boeing 737NG
CFM56-3 Boeing 737 Classic
AGSE-E092-G01† Inlet Cowl Dolly CFM56-7B Boeing 737NG
AM-2302N-100† Inlet Cowl Dolly CFM56-5C Airbus A340-200/-300 Trent 500, Trent 700
ENGINE COVERSDependable and lasting protection against dirt, water, and contamination!
PART NUMBER: Engine OEM ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
SHIPPING COVER TYPE(S):
BARE ENGINE QEC ENGINE REINFORCED WITH FITTED BAR
856A3700 CFM56-7B Boeing 737NG
856A2930 CFM56-5B Airbus A320 Family
856A2782 CFM56-5A Airbus A319 & A320
856A2330 CFM56-5C Airbus A340-200/-300
856A3505 CFM56-3 Boeing 737 Classic
856A3595 CFM56-3 Boeing 737 Classic
= Available Feature
4+1.562.906.9300 | www.agsecorp.com | [email protected]
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINES ENGINE SLINGS, PEDESTAL SETS &
BOOTSTRAP SYSTEMS
PEDESTAL SETSAnother ideal horizontal build-up solution that achieves ergonomically efficient engine centerline heights!
PART NUMBER: Engine OEMAGSE
ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
ENGINE MODULE(S) SUPPORTED BY PEDESTAL(S)
NUMBER OF PEDESTALS MAXIMUM LOAD CAPACITY ACHIEVES ENGINE
CENTERLINE HEIGHT(S)
856A1312
CFM56-7BCFM56-5A/-5BCFM56-5CCFM56-3
Boeing 737NGAirbus A320 FamilyAirbus A340-200/-300Boeing 737 Classic
Forward Full Engine 2 1,000 lbs, 454 kg (per set) 65.4”, 166 cm
Aft Full Engine 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
Forward Fan Module 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
Aft Fan Module 2 1,000 lbs, 454 kg (per set) 65.4”, 166 cm
High Pressure Compressor Case 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
Rear Low Pressure Turbine Frame 2 1,500 lbs, 680 kg (per set) 65.4”, 166 cm
AGSE-T016-G071/-G09 CFM56-7B Boeing 737NG QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)6,000 lbs, 2,722 kg (Aft Pedestals, Set of 2)
60", 152 cm
AGSE-T016-G03 CFM56-5A/-5B Airbus A320 Family QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)4,000 lbs, 1,814 kg (Aft Pedestals, Set of 2)
69", 175 cm
AGSE-T016-G11 CFM56-5C Airbus A340-200/-300 QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)4,000 lbs, 1,814 kg (Aft Pedestals, Set of 2)
69", 175 cm
AGSE-T016-G06 CFM56-3 Boeing 737 Classic QEC Engine 4
7,000 lbs, 3,175 kg (Forward Pedestals, Set of 2)2,700 lbs, 1,225 kg (Aft Pedestals, Set of 2)
56", 142 cm
AGSE-T025-G02 CFM56-5C Airbus A340-200/-300 QEC Engine 4
4,800 lbs, 2,177 kg (Forward Ring)4,000 lbs, 1,814 kg (Aft Pedestals, Set of 2)
58"–64", 147 cm–163 cm
AM-1953-100 CFM56-3 Boeing 737 Classic QEC Engine 4
4,800 lbs, 2,177 kg (Forward Ring)6,000 lbs, 2,722 kg (Aft Pedestals, Set of 2)
56", 142 cm
ENGINE SLINGSStable and versatile overhead support for horizontal build-up or engine transfer to or from Shipping Stands!
PART NUMBER: AGSE ENGINE(S)ACCOMMODATED
AIRCRAFT APPLICATION(S) MAXIMUM LOAD CAPACITY COMPATIBLE WITH
AGSE SHIPPING CRADLESCENTER OF GRAVITY
ADJUSTMENT FEATUREACCOMMODATES OTHER
SELECT ENGINES
AM-2106
CFM56-7B Boeing 737NG 6,800 lbs, 3,084 kg
Hand Crank CF6, PW2000, PW4000, RB211
CFM56-5A Airbus A319, A320 6,900 lbs, 3,130 kg
CFM56-5B Airbus A320 Family 7,000 lbs, 3,175 kg
CFM56-5C A340-200/-300 7,500 lbs, 3,402 kg
CFM56-3 Boeing 737 Classic 5,750 lbs, 2,608 kg
AGSE-L006† CFM56-5A/-5B Airbus A320 Family 18,000 lbs, 8,165 kg AM-2718-C1 Lifting Shackle CF6
AGSE-L012-G01† CFM56-3 Boeing 737 Classic 16,000 lbs, 7,257 kg AM-1802 Lifting Shackle CF6, RB211
AGSE-L002† CFM56-3 Boeing 737 Classic 12,000 lbs, 5,443 kg Cable Sling Hook Point CF6, PW2000, PW4000
AM-1949 CFM56-3 Boeing 737 Classic 10,000 lbs, 4,536 kg Lifting Shackle
1Universal model accommodates multiple mounting adapters to achieve variable engine centerline height(s)
BOOTSTRAP SYSTEMS All-in-One Engine Sling and Adapter Kits for more convenient bootstrap operations!
PART NUMBER: AGSE DESCRIPTION ENGINE(S) ACCOMMODATED
AIRCRAFT APPLICATION(S)
MAXIMUM PROOF LOAD CAPACITY
COMPATIBLE WITH AGSE SHIPPING CRADLES KIT INCLUDES:
AM-1916 Manual Bootstrap System CFM56-3 Boeing 737 Classic
7,000 lbs, 3,175 kg (Forward Beam)2,000 lbs, 907 kg (Aft Beam)
AM-1802
• Forward & Aft Bootstrap Beam Assemblies • Bootstrap Adapters• Three (3) Wired Rope Hoists• Attaching Hardware • Reusable Shipping Container
5+1.562.906.9300 | www.agsecorp.com | [email protected]
MODULE SHIPPING CONTAINERS BY PART NUMBER
PART NUMBER: AGSE ENGINE MODULE(S) SUPPORTEDIN SHIPPING CONTAINER
ENGINES(S)ACCOMMODATED
AIRCRAFT APPLICATION(S)
REMOVABLE COVER
SHOCK MOUNTS/ ISOLATION SYSTEM
SUPPORTING FOAM INSERTS
AGSE-C011† (AGSE-C026) Fan Disk & Booster Major Module 1 CFM56-7B Boeing 737NG
AGSE-C012 #1 & #2 Bearing Support Module 2 CFM56-7B Boeing 737NG
AGSE-C021 Low Pressure Turbine Module 13 CFM56-7B Boeing 737NG
AGSE-C022 Low Pressure Turbine Shaft Module 14 CFM56-7B Boeing 737NG
AGSE-C023 Low Pressure Turbine Frame Module 15 CFM56-7B Boeing 737NG
AGSE-C024 Transfer Gearbox Module 16 CFM56-7B Boeing 737NG
AGSE-C025 Accessory Gearbox Module 17 CFM56-7B Boeing 737NG
AGSE-C027 Fan Blades CFM56-7B Boeing 737NGAGSE-C028† (AGSE-C049) Low Pressure Turbine & Shaft Major Module 3 CFM56-7B Boeing 737NG
AGSE-C034 Core Module CFM56-7B Boeing 737NG
AGSE-C013 Core Module CFM56-5A Airbus A319, A320AGSE-C049 (AM-2141) Low Pressure Turbine & Shaft Major Module 3 CFM56-5A Airbus A319, A320
AM-2132 Fan Disk & Booster Module 1 CFM56-5A Airbus A319, A320
AM-2133 #1 & #2 Bearing Support Module 2 CFM56-5A Airbus A319, A320
AM-2134 Low Pressure Turbine Major Module 13 CFM56-5A Airbus A319, A320
AM-2135 Low Pressure Turbine Shaft Module 14 CFM56-5A Airbus A319, A320
AM-2136 Low Pressure Turbine Frame Major Module 15 CFM56-5A Airbus A319, A320
AM-2137 Transfer Gearbox Module 16 CFM56-5A Airbus A319, A320
AM-2138 Accessory Gearbox Module 17 CFM56-5A Airbus A319, A320
AM-2139 Major Module 1 CFM56-5A Airbus A319, A320
AM-2140 Fan Blades CFM56-5A Airbus A319, A320
AGSE-C009 Fan Disk & Booster Module 1 CFM56-5B Airbus A320 Family
AGSE-C010 #1 & #2 Bearing Support Module 2 CFM56-5B Airbus A320 Family
AGSE-C013 Core Module CFM56-5B Airbus A320 Family
AGSE-C044 Low Pressure Turbine Module 13 CFM56-5B Airbus A320 Family
AGSE-C045 Low Pressure Turbine Shaft Module 14 CFM56-5B Airbus A320 Family
AGSE-C046 Low Pressure Turbine Frame Module 15 CFM56-5B Airbus A320 Family
AGSE-C047 Fan Disk & Booster Major Module 1 CFM56-5B Airbus A320 Family
AGSE-C048 Fan Blades CFM56-5B Airbus A320 Family
AGSE-C049 Low Pressure Turbine & Shaft Major Module 3 CFM56-5B Airbus A320 Family
AM-2137 Transfer Gearbox Module 16 CFM56-5B Airbus A320 Family
AM-2138 Accessory Gearbox Module 17 CFM56-5B Airbus A320 FamilyAGSE-C049 (AM-2528) Low Pressure Turbine & Shaft Major Module 3 CFM56-5C Airbus A340-200/-300
AGSE-C050 Core Major Module CFM56-5C Airbus A340-200/-300
AM-2137 Transfer Gearbox Module 16 CFM56-5C Airbus A340-200/-300
AM-2138 Accessory Gearbox Module 17 CFM56-5C Airbus A340-200/-300
AM-2519 Booster Module 1 CFM56-5C Airbus A340-200/-300
AM-2520 #1 & #2 Bearing Support Module 2 CFM56-5C Airbus A340-200/-300
AM-2521 Low Pressure Turbine Module 13 CFM56-5C Airbus A340-200/-300
AM-2522 Low Pressure Turbine Shaft Module 14 CFM56-5C Airbus A340-200/-300
AM-2523 Low Pressure Turbine Frame Module 15 CFM56-5C Airbus A340-200/-300
AM-2526 Fan Case Major Module 1 CFM56-5C Airbus A340-200/-300
AM-2527 Fan Blades CFM56-5C Airbus A340-200/-300
AGSE-C007 Fan Booster CFM56-3 Boeing 737 Classic
AGSE-C008 #1 & #2 Bearing Support Module 2 CFM56-3 Boeing 737 Classic
AGSE-C035 Fan Disk & Booster Module 1 CFM56-3 Boeing 737 Classic
AGSE-C036 Core Module CFM56-3 Boeing 737 Classic
AGSE-C037 Low Pressure Turbine & Shaft Major Module 3 CFM56-3 Boeing 737 Classic
AGSE-C038 Low Pressure Turbine Module 13 CFM56-3 Boeing 737 Classic
AGSE-C039 Low Pressure Turbine Shaft Module 14 CFM56-3 Boeing 737 Classic
AGSE-C040 Low Pressure Turbine Frame Module 15 CFM56-3 Boeing 737 Classic
AGSE-C041 Transfer Gearbox Module 16 CFM56-3 Boeing 737 Classic
AGSE-C042 Accessory Gearbox Module 17 CFM56-3 Boeing 737 Classic
AGSE-C043 Fan Blades CFM56-3 Boeing 737 Classic
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-3, CFM56-5 & CFM56-7 engines (unless denoted with a † ).
OEM-APPROVED FOR CFM56 ENGINE MODULES SHIPPING CONTAINERS
Fully enclosed to shield major modules against contamination and damage during split engine transport!
= Available Feature
6+1.513.402.7246 | www.agsecorp.com | [email protected] 6
LINE MAINTENANCE TOOLINGPART
NUMBER: CFM INT'L
DESCRIPTION
856A2609 Jacking Block - Fuel Pump/MEC or HMU856A2668 Puller Adapters856A2682 Eddy Current Inspection Kit - Fan Blades856A2686 Hand Cranking Drive Socket856A2691 Removal Tool - Spacer Pliers856A2953 Guide Pins - Stator Alternator 856A2956 Assistance Tool - Ring Fan Assembly
856A2957 Tool Set - Assembly/Disassembly Lubrication Unit Scavenge Filter Housing
856A2958 Actuation Hose Assembly - VSV 856A2961 Installation/Removal Tool - AGB Oil & Magnetic Seal856A3074 Balance Weights Riveter - Booster856A3519 Three (3) Legs Handling Sling - AGB856A3525 Removal/Installation Cradle - AGB 856A3557 D-Seal Tool - Magnetic Plug Lube Unit856A3576 Removal/Installation Tool - AGB Seals (7B27A) 856A3583 Leak Test Oil Seals
856A3598 Removal/Installation Cradle - Fuel Pump & MEC Package
856A3604 Wrench - Horizontal Drive Shaft Nut 856A3617 Pusher/Puller - Lube Unit Magnetic Plug856A3708 Pusher/Puller - Radial Drive Shaft856A3709 Alignment Fixture - AGB856A3726 Protective Floor - Fan Inlet Case856A3728 Core Engine Sealing Plate & Lock856A3770 Fan Blade Plotting Software856A3771 Check Template - Fan Blade Leading Edge856A3778 Guide Pins - Rear Spinner856A3779 Platform Puller - Fan Blade856A3782 Removal Wrench - Fan Blade Retainer Ring856A4624 Scouring Fixture - Fan Case Abradable Strip856A4628 Blade Template (Inches)856A4637 Inspection Tool - Booster Spool Forward Flange856A4640 Inspection Tool - Fan Disk Lugs856A4646 Gauge - Fan Blade Rear Shank856A5564 Resurfacing Kit - Spherical End Tube Coupling856A5807 Spiral Stencil - Front ConeFAN & BOOSTER MODULE TOOLING856A2316 Torque Wrench - LPT Coupling Nut856A2555 Lifting Beam - Fan Frame 856A2625 Storage Stand - LP Module856A2644 Tool Lock - Fan Disk
856A2655 Installation/Removal Fixture - Radial Drive Shaft Housings
856A2663 Puller Adapter - Splitter Fairing856A2694 Installation Tool - Inner Housing856A3501 Alignment/Guide Fixture - Booster to LPT Shaft856A3504 Pusher/Puller Fixture856A3524 Drive Adapter Tool Set - Booster & LPT 856A3702 Removal/Installation Centering Sleeve - MM3856A3703 Countertorque Wrench Guide856A3704 Residual Torque Beam856A3723 Guiding & Pulling Fixture - Booster856A3724 Tool Set - Sighting Fan Disk Coupling Bolts856A3725 Torque/Loosen Wrench - Fan Disk856A3732 Handling Fixture - Booster Rotor/Stator
856A5684 Eddy Current Inspection Kit - Fan Disk Inside Diameter
856A5945 Alignment Master - LPT Shaft
#1 & #2 BEARING TOOLING PART
NUMBER: CFM INT'L
DESCRIPTION
856A2336 Puller - Forward Rotating Air/Oil Separator 856A2609 Jacking Block - Fuel Pump /MEC or HMU856A2626 Storage Stand - No.1 & No.2 Bearing856A2640 Holder - Oil Separator Duct856A2662 Tool Kit - Masters Air Nozzles 856A2667 Check Tool - Assembly/Disassembly Circular Runout856A2745 Thickness Gauge Tool - Phonic Wheel856A2923 Supporting Guide - No.1 Bearing856A3011 Plug Extractor856A3012 Puller - No.2 Bearing Inner Race (with Actuator)856A3013 Puller - No.1 Sensor Ring (with Actuator)856A3033 Fixture - No.1 Bearing Sleeve Nut Retaining856A3267 Adapter Test Rig - No.1 & No.2 Bearing Air Flow856A3323 Center Bushing - No.1 Ball Bearing
856A3489 Targets Tool Set - No.1 Bearing Air Impingement Checks
856A3556 Axial Weight Loading - No.1 Bearing856A3570 Wrench - No.2 Bearing Inner Race Seal856A3571 Wrench - Forward Rotating Air/Oil Separator Nut 856A3572 Wrench - No.1 Bearing Inner Race Nut856A3628 Installation Tool - No.1 Bearing Inner Race
856A3721 Lift & Turn Adapter Tool Set - No.1 & No.2 Bearing Support
856A3722 Dummy - Fan Disk856A3736 Locating Template - Drain Tube & OilCORE MODULE TOOLING856A2812 Dolly Fixture - Torque HP856A2818 Dolly - Tool Seating Check Core HP856A2821 Lube Protective Washer - No.4 Bearing Retainer856A2822 Torque Fixture - No.4 Bearing Retainer 856A2868 Protector - Fan ShaftLOW PRESSURE TURBINE (LPT) MODULE TOOLING856A2568 Lifting Ring - Aft LPT Shaft856A2577 Locating Ring - No.5 Bearing Rollers856A2600 LPT Shaft Guide & Stop Tool Guide856A2618 Holding Fixture - Rotor/Stator856A2647 Transportation/Storage Stand - LPT Major Module856A2660 Measuring Gauge - LPT Axial Clearance856A2661 Puller - Aft Rotating Air/Oil Separator 856A2674 Protection Cover - LPT Shaft856A2676 Checking Gauge - LPT MO1B Clearance (7BE)
856A2677 Installation/Removal Fixture - Removable Retaining Ring
856A2685 Puller Adapter - Oil Inlet Cover (Hydraulic or Manual Option)
856A2692 Eddy Current Inspection Kit - TRF856A2702 Pin Guide - No.5 Bearing
856A2710 Handling Fixture - LPT Major Module (also accommodates CFM56-5B engines)
856A2713 Build-Up Fixture - LPT Shaft Module to LPT Module856A2714 Hoist Fixture - LPT Module856A2722 Guide Pins - LPT Frame to LPT Case 856A2729 Handling/Turn Fixture - LPT Case856A2731 Support Sectors - LPT Shaft to LPT 856A2750 Fixture - Stage 1 through 4 LPT Blades856A2752 Restrain Hooks - Air Seal to LPT Disassembly856A2755 Tool Set - Seals to Cone Stub Shaft856A2756 Heater - LPT Shaft to Stub Shaft (110V or 220V Option)856A2759 Puller Seals Tool Set856A2760 Support Handle Ring - Cone Stub Shaft & Stage 3 Disk856A2764 Heater Set - LPT (110V or 220V Option)856A2766 Support Ring - Cone Stub Shaft856A2773 Support Spacers - LPT Rotor/Case 856A2789 Ring - Center Aft Rotating Air Seal856A2826 Holding Fixture - No.4 Bearing Inner Race Bolts
LPT MODULE TOOLING (CONTINUED)PART NUMBER:
AGSE CFM INT'L
DESCRIPTION
856A2943 Protection Sleeve - Rear Inner Rotating Air/Oil Seal 856A2968 Heating Tool - Center Vent Tube (110V or 220V Option)856A3062 Puller - Rear Rotating Air/Oil Seal 856A3100 Locating Pin - Center Vent Tube 856A3234 Protector - Aft Center Vent Tube856A3268 Wrench - Center Vent Tube Sleeve Nut856A3269 Wrench - No.5 Bearing Inner Race Nut856A3279 Pusher/Puller - LPT Disk Sleeves856A3308 Puller - No.4 Bearing Inner Race856A3315 Puller - Center Vent Tube 856A3385 Wrench - Stage 1 LPT Disk Bolts856A3392 Torque Nut Wrench - Aft Rotating Air/Oil Separator856A3419 Puller Adapter - Oil Inlet Cover 856A3432 Gauge - LPT Stub Shaft to LPT Shaft856A3443 Puller - No.5 Bearing Outer Race856A3483 Protective Ring - No.4 Bearing856A3484 Protective Ring - No.5 Bearing 856A3485 Protective Cap - LPT Shaft Thread856A3487 Protector - No.4 Ball Bearing856A3488 Holding Fixture - Sectors Support 856A3491 Counter Wrench - No.5 Bearing Support Nipple856A3492 Counter Wrench - No.5 Bearing Support Nipple Line856A3501 Alignment/Guide Fixture - Booster to LPT Shaft856A3748 Protection Cover - Stage 1 LPT Disk856A3749 Installation Tool Set - Stage 2 & 3 Strips856A3750 Centering Fixture - LPT Shaft Module
856A3751 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A3752 Removal Fixture - Stage 1-2-3 Outer Stationary Air Seal856A3755 Foolproof Installation Tool - Stage 1 LPT & Air Seal856A3756 Installation Fixture - Stage 2 Shield856A3757 Installation Fixture - Stage 3 Shield
856A3760 Assembly/Disassembly Fixture - Stage 2 LPT Nozzle Segments
856A3761 Installation Tool Set - Stage 2 LPT Outer Stationary Seal856A3762 Assembly/Disassembly Fixture - LPT Rotor/Stator
856A3763 Assembly/Disassembly Fixture - Stage 3 LPT Nozzle Segments
856A3764 Installation Tool Set - Stage 3 LPT Outer Stationary Air Seal
856A3766 Handling Fixture Support - LPT Rotor/Stator856A3767 Handling Fixture - LPT Rotor/Stator
856A3788 Installation Tool Set - Stage 2 & 3 LPT Outer Stationary Air Seal
856A3790 Pusher/Puller Fixture - Duct Rear856A3791 Machining Fixture Adjusting Sleeve - No.5 Bearing856A3792 Centering Fixture - LPT Shaft to LPT856A3793 Pusher/Puller Fixture - Center Vent Tube
856A3794 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A3795 Mobile Stand - LPT Module856A3799 Guide Pin - No.5 Bearing Support 856A5944 Alignment Fixture - LPT ShaftENGINE SHIPPING, LIFTING & STORAGEAM-2563-227 Transportation Base (Wide Fork)AM-2811-4800 Shipping Cradle
856A1312 Engine Handling Support (also accommodates CFM56-5B engines)
856A2627 Lifting Beam856A2645 Engine Variable CG Beam856A2651 Engine Support Pad856A3515 Extension Beam - Variable CG Lift Fixture856A3700 Fitted Bar Engine Shipping Cover856A3710 Lifting Beam (2,000 daN/4,400 lbs Capacity)
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-7B engines.
OEM-APPROVED FOR CFM56-7B ENGINE MODULES SELECT LINE, HANGAR &
SHOP MAINTENANCE TOOLING
High-Quality engine tooling for airlines, MRO shops, lessors, and OEM customers!
Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!
7+1.513.402.7246 | www.agsecorp.com | [email protected]
LINE MAINTENANCE TOOLINGPART NUMBER:
CFM INT'L DESCRIPTION
856A2320 Tool Set - Engine Sumps Relube
856A2501 Dual Purpose Ratchet Wrench - VBV Manual Control
856A2537 Mounting Pin Protector - Accessory Drive Major Module
856A2609 Jacking Block - Fuel Pump/MEC or HMU
856A2645 Engine Variable CG Beam
856A2655 Fixture - Radial Drive Shaft Housings Installation/Removal
856A2659 Filter Adapter - Dry Out
856A2663 Puller Adapter - Splitter Fairing
856A2664 Setting Gauge - VBV Doors
856A2673 Installation Tool - Enerseal Seal
856A2677 Installation/Removal Fixture - Removable Retaining Ring
856A2678 CFMI Software - Trim Balance
856A2680 Vibration Software - No.4 Bearing
856A2686 Hand Cranking Drive Socket
856A2689 Vibration Analyzer Kit
856A2707 Leak Test Tool Set - AGB
856A2717 Lock Adapter - Core Engine
856A2718 Tool Set - Manual Drive Shaft
856A2719 Removal/Installation Support Fixture - TGB
856A2727 Puller - Radial Drive Shaft
856A2737 Leak Test Tool Set - AGB
856A2754 Support Fixture - AGB
856A2794 Protector Set - Seal Fitting
856A2796 Safety Protector Handcranking Pad
856A2805 Turnbuckle - AGB/TGB
856A2809 Back-Up Filter Handle Removal
856A2930 QEC Engine Shipping Cover
856A2947 Fan Blade Contour Template
856A2948 Fan Blades Liner Patch Inflatable Pressure Tool (220V/50Hz)
856A2949 Fan Blade Leading Edge Template
856A2953 Guide Pins - Stator Alternator
856A3409 Guide Pins - Spinner Rear Cone
856A3471 Drive Spline Adapter Fuel Pump (US Configuration)
856A3492 Counter Wrench - No.5 Bearing Support Nipple Line
856A3519 Three (3) Legs Handling Sling - AGB
856A3576 Removal/Installation Tool - AGB Seals
856A3770 Fan Blade Mapping Program Software
856A5649 Fan Disk Mirror Inspection
856A5817 Check Fan Blade Shank
856A5931 Fan Disk Dovetail Slots Gauge
856A5942 Fan Disk Dovetail Slots Gauge
FAN REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2555 Lifting Beam - Fan Frame
856A3111 Trunnion Dolly - Fan Frame Module
FAN ASSEMBLY/DISASSEMBLY856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module
856A2310 Alignment Fixture - Booster to LPT Shaft
856A2311 Dummy Tube - LPT Rotor Shaft Forward End
856A2571 Guide Pins - No.1 & No.2 Bearing Support Module Installation
856A2625 Storage Stand - Fan & Booster Module
856A2626 Storage Stand - Module 2
856A2667 Check Assembly/Disassembly Tool - Circular Runout
856A2701 Protective Floor - Fan Inlet Case Turbine Frame
856A2720 Machining Fixture - Fan Case Abradable Strip
FAN ASSEMBLY/DISASSEMBLY (CONTINUED)PART NUMBER:
CFM INT'L DESCRIPTION
856A2753 Accessory Drive Dummy
856A2902 Dummy Fan Disk
856A2904 Handling Fixture - Booster Rotor/Stator Assembly
856A2906 Guide & Countertorque Wrench
856A2907 Machining Fixture - Abradable Strip Fan Casing
856A2951 Counterweight Tool
856A2986 Alignment Fixture - Guide Booster
856A3111 Trunnion Dolly - Fan Frame Module
856A3267 Test Rig Adapter - No.1 & No.2 Bearing Support Air Flow Check
856A3409 Guide Pins - Spinner Rear Cone
856A3510 Lift & Turn Adapter - Module 2
856A3515 Extension Beam - Variable CG Lift Fixture
856A3608 Axial Loading Fixture
856A5939 Tool - Fan Blade Tip Clearance
FAN & BOOSTER MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module
856A2310 Alignment Fixture - Booster to LPT Shaft
856A2318 Thermal Shield
856A2501 Dual Purpose Ratchet Wrench - VBV Manual Control
856A2625 Storage Stand - Fan & Booster Module
856A2627 Lifting Beam
856A2631 Storage Stand - Fan Blades
856A2632 Puller
856A2644 Holding Tool - Fan Disk
856A2663 Puller Adapter - Splitter Fairing
856A2701 Protective Floor - Fan Inlet Case Turbine Frame
856A2780 Handling Adapter
856A2903 Torque Adaptation Beam
856A2904 Handling Fixture - Booster Rotor/Stator Assembly
856A2905 Torque/Loosen Wrench - Fan Disk Coupler
856A2906 Guide & Countertorque Wrench
856A2946 Protective Ring - Fan Disk
856A2951 Counterweight Tool
856A3111 Trunnion Dolly - Fan Frame Module
856A3504 Pusher/Puller Fixture - Module 1 & Major Module 3
856A3515 Extension Beam - Variable CG Lift Fixture
856A3524 Drive Adapter Tool Set - Booster & LPT
856A3793 Pusher/Puller Fixture - Center Vent Tube
856A5939 Tool - Fan Blade Tip Clearance
NO.1 & NO.2 BEARING SUPPORT MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module 856A2310 Alignment Fixture - Booster to LPT Shaft 856A2316 Torque/Loosen Wrench - LPT Coupling Nut856A2571 Installation Guide Pins - No.1 & No.2 Bearing Support Module856A2616 Centering Sectors - Forward LPT Shaft856A2626 Storage Stand - Module 2856A2701 Protective Floor - Fan Inlet Case Turbine Frame856A2709 Forward Support Guide856A2780 Handling Adapter856A2902 Dummy Fan Disk856A2903 Torque Adaptation Beam856A2906 Guide & Countertorque Wrench856A2909 Guide Pins - No.1 & No.2 Bearing Tubes 856A3510 Lift & Turn Adapter - Module 2 856A3515 Extension Beam - Variable CG Lift Fixture
OEM-APPROVED FOR CFM56-5A/-5B/-5C ENGINE MODULES SELECT LINE, HANGAR &
SHOP MAINTENANCE TOOLING
Guaranteed deliveries and round-the-clock after-sales service!
More Select CFM56-5A/-5B/-5C Tooling on Page 8
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-5A/-5B/-5C engines.
Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!
8+1.513.402.7246 | www.agsecorp.com | [email protected]
CORE MODULE REMOVAL/INSTALLATIONPART NUMBER:
CFM INT'L DESCRIPTION
856A2812 Dolly Fixture - Torque HP
856A2818 Tool Seating Check Dolly - Core
856A2866 Protector - Fan Shaft
856A2946 Protective Ring - Fan Disk
856A2997 Seating Check Gauge - Core Module to IGB
HIGH PRESSURE TURBINE (HPT) TOOLING856A2821 Lubricant Shield (Protective Washer) - No.4 Bearing Retainer
856A2822 Torque Fixture - No.4 Bearing Retainer
LPT MODULE REMOVAL/INSTALLATION856A2308 Centering & Removal/Installation Sleeve - Module 1/LPT Major Module
856A2310 Alignment Fixture - Booster to LPT Shaft
856A2316 Torque/Loosen Wrench - LPT Coupling Nut
856A2412 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A2600 Guide & Stop Tool - LPT Shaft
856A2618 Holding Fixture - Rotor/Stator
856A2627 Lifting Beam
856A2632 Puller
856A2647 Mobile Storage Stand - Horizontal Major Module 3
856A2661 Puller - Aft Rotating Air/Oil Separator
856A2668 Puller Adapter Kit
856A2685 Puller Adapter - Oil Inlet Cover
856A2710 Handling Fixture - LPT Major Module
856A2717 Lock Adapter - Core Engine
856A2780 Handling Adapter
856A2903 Torque Adaptation Beam
856A2906 Guide & Countertorque Wrench
856A2946 Protective Ring - Fan Disk
856A2950 Centering Fixture - LPT Shaft
856A2968 Heating Tool - Center Vent Tube (110V or 220V Option)
856A3234 Protective Cap - Center Vent Tube, Rear Extension Duct
856A3392 Torque Nut Wrench - Aft Rotating Air/Oil Separator
856A3419 Puller Adapter - Oil Inlet Cover & Major Module 3
856A3485 Protective Cap - LPT Shaft Thread
856A3487 Protector - No.4 Ball Bearing
856A3504 Pusher/Puller Fixture - Module 1 & Major Module 3
856A3524 Drive Adapter Tool Set - Booster & LPT
856A3793 Pusher/Puller Fixture - Center Vent Tube
856A3794 Holding Ring - Stage 1 Outer Stationary Seal & Turbine Shroud Support
856A5944 Alignment Fixture - LPT Shaft
856A5945 Alignment Master - LPT Shaft
LPT MODULE DISASSEMBLY/ASSEMBLY856A2349 Assembly/Disassembly & Storage Dolly - LPT Shaft
856A2412 Holding Ring - Stage 1 Outer Stationary Air Seal & Turbine Shroud Support
856A2544 Trunnion Dolly - Turbine Frame Module
856A2567 Forward Lifting Eye - LPT Shaft
856A2568 Aft Lifting Eye - LPT Shaft
856A2577 Locating Ring - No.5 Bearing Rollers
856A2618 Holding Fixture - Rotor/Stator
856A2627 Lifting Beam
856A2646 Trunnion Dolly - Turbine Frame Maintenance Module
856A2647 Mobile Stand - Horizontal Major Module 3 Storage
856A2710 Handling Fixture - LPT Major Module
856A2712 Handling Segments - Turbine Frame Module
856A2713 Buildup Fixture - LPT Shaft to LPT Module
LPT MODULE DISASSEMBLY/ASSEMBLY (CONTINUED)PART NUMBER:
CFM INT'L DESCRIPTION
856A2714 Hoist Fixture - LPT Module
856A2715 Storage Stand - LPT Module
856A2716 Distribution Ring
856A2722 Guide Pins - Turbine Frame to LPT Case
856A2731 Support Sectors - LPT Shaft to LPT Module
856A2756 Heat Diffuser - LPT Shaft (without Heat Gun)
856A2758 Centering Fixture - LPT Shaft to LPT
856A2772 Puller - LPT Rear Frame/LPT Case
856A2943 Protection Sleeve - Rear Inner Rotating Air/Oil Seal
856A2950 Centering Fixture - LPT Shaft
856A3234 Protective Cap - Center Vent Tube, Rear Extension Duct
856A3247 Alignment Guide - LPT Rear Frame to LPT Shaft
856A3383 Alignment Fixture - LPT Rear Frame to LPT
856A3484 Protective Ring - No.5 Bearing
856A3485 Protective Cap - LPT Shaft Thread
856A3487 Protector - No.4 Ball Bearing
856A3488 Holding Fixture Support - LPT Shaft
856A3759 Handling Sectors - Turbine Frame Module
856A3791 Machining Fixture Adjusting Sleeve - No.5 Bearing
856A3792 Centering Fixture - LPT Shaft to LPT
856A3794 Holding Ring - Stage 1 Outer Stationary Seal & Turbine Shroud Support856A3795 Mobile Stand - LPT ModuleTURBINE FRAME MODULE REMOVAL/INSTALLATION856A1312 Engine Handling Support (also accommodates CFM56-7B engines)
856A2544 Trunnion Dolly - Turbine Frame Module
856A2627 Lifting Beam
856A2646 Trunnion Dolly - Turbine Frame Maintenance Module
856A2651 Engine Support Pad
856A2712 Handling Segments - Turbine Frame Module
856A2722 Guide Pins - Turbine Frame to LPT Case
856A2772 Puller - LPT Rear Frame/LPT Case
856A2773 Support Spacers - LPT Rotor/LPT Case
856A3234 Protective Cap - Center Vent Tube, Rear Extension Duct
856A3247 Alignment Guide - LPT Rear Frame to LPT Shaft 856A3383 Alignment Fixture - LPT Rear Frame to LPTINLET GEARBOX (IGB) & #3 BEARING MODULE REMOVAL/INSTALLATION856A2310 Alignment Fixture - Booster to LPT Shaft
856A2616 Centering Sectors - Forward LPT ShaftTRANSFER GEARBOX (TGB) MODULE REMOVAL/INSTALLATION856A2414 Fixture - Guide Radial Shaft
856A2537 Mounting Pin Protector - Accessory Drive Major Module
856A2632 Puller
856A2718 Tool Set - Manual Drive Shaft
856A2719 Remove/Install Support Fixture - TGB
856A2727 Puller - Radial Drive Shaft
856A2805 Turnbuckle - AGB/TGB
ACCESSORY GEARBOX (AGB) MODULE REMOVAL/INSTALLATION856A2537 Mounting Pin Protector - Accessory Drive Major Module
856A2609 Jacking Block - Fuel Pump/MEC or HMU
856A2632 Puller
856A2718 Tool Set - Manual Drive Shaft
856A2754 Support Fixture - AGB
856A2805 Turnbuckle - AGB/TGB
856A2953 Guide Pins - Stator Alternator
856A3519 Three (3) Legs Handling Sling - AGB
OEM-APPROVED FOR CFM56-5A/-5B/-5C ENGINE MODULES SELECT LINE, HANGAR &
SHOP MAINTENANCE TOOLING
Competitive pricing and expert consultation ensure an optimal Return on Investment!
©2021 AGSE-Westmont Industries. All rights reserved. R.9.1.21
Approved, qualified, and recommended by CFM International, GE Aviation, or Safran Aircraft Engines for the handling of CFM56-5A/-5B/-5C engines.
Contact AGSE Customer Service to Discover Additional OEM-Approved CFM56 Tooling!