ENG

LISH

AVR 347 Audio/VideoReceiverOWNERS MANUAL

347

2 TABLE OF CONTENTS

3 Introduction4 Safety Information5 Unpacking6 Front Panel Controls8 Rear Panel Connections

11 Main Remote Control Functions15 Zone II Remote Control Function17 Installation and Connections17 Audio Equipment Connections17 HDMI Input Connections17 HDMI Output Connections18 Video Equipment Connections19 SCART A/V Connections21 System and Power Connections22 Speaker Selection22 Speaker Placement23 System Configuration23 First Turn On23 Using the On-Screen Display23 System Setup24 Input Setup26 Surround Setup27 Night Mode Settings28 Configuring the Surround Off

(Stereo) Modes28 Automated Speaker Setup Using EzSet/EQ31 Manual Setup31 Speaker Setup34 Delay Settings35 Output Level Adjustment37 Operation37 Surround Mode Chart39 Basic Operation39 Source Selection39 Video Input Selection40 6/8-Channel Direct Input40 Controls and Use of Headphones40 Surround Mode Selection41 Digital Audio Playback41 Dolby Digital41 DTS41 PCM Audio Playback41 Selecting a Digital Source42 Digital Bitstream Indicators42 Surround mode Types43 Surround Mode Post Processing43 PCM Playback Indications44 Speaker/Channel Indicators44 Night Mode45 Tape Recording45 Using The Bridge 46 Output Level Adjustment

With Source Signals46 Dim function46 Memory backup47 Multiroom Operation47 Multiroom 47 Installation47 Multiroom Setup47 Surround Amplifier Channel Assignment47 Multiroom Operation49 Video Adjustments49 Advanced Features49 Front Panel Display Fade50 Turn-On Volume Level50 Semi-OSD Settings50 Full-OSD Time Out Adjustment51 Default Surround Mode

Table of Contents

Typographical ConventionsIn order to help you use this manual with the remote control, front-panel controls and rear-panelconnections, certain conventions have been used.

EXAMPLE (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack

EXAMPLE (OCR type) indicates a message that is visible on the front-panel information display

1 (number in a square) indicates a specific front-panel control

(number in a circle) indicates a rear-panel connection

0 (number in an oval) indicates a button or indicator on the remote

(letter in an oval) indicates a button on the Zone II remote

The appearance of the text or cursor for your receivers on-screen menus may vary slightly from theillustrations in this manual. Whether the text appears in all uppercase or upper- and lowercasecharacters, performance and operation remain the same.

Declaration of Conformity

We, Harman Consumer Group, Inc.2, route de Tours72500 Chteau-du-Loir,FRANCE

declare in own responsibility, that the productdescribed in this owners manual is in compliancewith technical standards:

EN 55013:2001 + A1:2003EN 55020:2002 + A1:2003EN 61000-3-2:2000EN 61000-3-3:1995 + A1:2001EN 60065:2002

Jurjen AmsterdamHarman Consumer Group, Inc.

04/07

51 Tuner Operation51 Basic Tuner Operation51 Station Selection51 Preset Tuning52 RDS Operation52 RDS Tuning52 RDS Display Options52 Program Search53 Programming the Remote53 Programming the Remote with Codes53 Direct Code Entry53 Auto Search Method53 Code Readout

54 Learning Codes from a Remote54 Erasing Learned Codes55 Macro Programming55 Programmed Device Functions56 Volume Punch-Through56 Channel Control Punch-Through56 Transport Control Punch-Through57 Resetting the Remote Memory58 Function List60 Troubleshooting Guide60 Processor Reset61 Technical Specifications62 Appendix - Settings Worksheet

INTRODUCTION 3

ENG

LISH

Introduction

Thank you for choosing Harman Kardon! With the purchase of a Harman Kardon AVR 347you are about to begin many years of listeningenjoyment. Designed to provide all the excitementand detail of movie soundtracks and every nuanceof musical selections, the AVR 347 is truly amultichannel receiver for the new millennium. Inaddition to the traditional 5.1 digital decodingmodes such as Dolby Digital and DTS, it offers thelatest advancements in surround technology suchas Dolby Pro Logic II and IIx, the full suite of DTS-ES 6.1 modes, DTS Neo:6 and the latest 7.1channel versions of Harman's own Logic 7technology.

The AVR 347 has been engineered so that it iseasy to take advantage of all the power of itsdigital technology. On-screen menus, fully colorcoded connection jacks and terminals makeinstallation fast and simple. However, to obtainthe maximum enjoyment from your newreceiver, we urge you to read this manual. A fewminutes spent learning the functions of thevarious controls will enable you to takeadvantage of all the power the AVR 347 is ableto deliver.

If you have any questions about this product, itsinstallation or its operation, please contact yourretailer or custom installer. They are your bestlocal sources of information.

Description and FeaturesThe AVR 347 serves as the hub of your homeentertainment system, providing a wide range oflistening possibilities for almost any audio orvideo program source, whether it is the broad-cast of a movie or sporting event in HDTV or avintage mono or stereo recording. When playingdigital audio sources from either the convention-al optical and coaxial inputs, or through theHDMI 1.1 compliant connections, the AVR 347decodes Dolby Digital, Dolby Digital EX, DTS andDTS-ES data streams. Two-channel stereo andmatrix surround sources benefit from all currentDolby Pro Logic IIx modes and DTS Neo:6. Thelatest version of our proprietary Logic 7 processis on-board to create a wider, more envelopingsound field and more defined surround channelpositioning, regardless of the type of sourcematerial.

Dolby Virtual Speaker is available to createenveloping sound fields from front left and rightspeakers, and the latest Dolby Headphonecircuitry creates an amazing sense of opennesswith headphones.

The AVR 347 takes the video part of its nameseriously. Along with two HDMI inputs and three100MHz analog component video inputs, theAVR 347s video processing allows you to scalethe output signal to 720p with 1080i and 1080ploop-through to match the requirements of yourspecific video display. Thanks to award winningFaroudja technology, your video sources neverlooked better. Tying audio and video together,the AVR 347 provides A/V sync delay so that thelip sync errors commonly seen when digitalvideo processing is used in a source, program orvideo display are eliminated.

An important addition to the AVR 347s impres-sive list of features is EzSet/EQ, which auto-mates the configuration process to make itquicker, easier and more precise. Using the spe-cial microphone supplied with the unit, EzSet/EQtakes the guesswork out of entering speakersize and crossover information, delay times forall channels and output levels. In addition to theconfiguration settings, EzSet/EQ also includesroom equalization so that the signals sent toeach speaker are tailored to provide accuratesonic quality with your specific combination ofspeaker type, room size and other factors thatinfluence room acoustics. With EzSet/EQ, yoursystem is custom-configured in a few minuteswith accuracy that previously required expensiveand hard-to-use test equipment.

In tandem with EzSet/EQ, the AVR 347 includesa full set of manual configuration settings forthose who wish to custom-trim their systemeven further. A Quadruple Crossover bassmanagement system makes it possible to enterdifferent crossover settings for each speakergroup.

A Stereo-Direct mode bypasses the digitalprocessor to preserve all of the subtleties of olderanalog, two-channel materials, while bassmanagement, available in the surround andStereo-Digital modes, improves your ability totailor the sound to suit your room acoustics ortaste.

For the ultimate in flexibility, the AVR featuresconnections for five video devices, all with bothcomposite and S-Video inputs. Two additionalaudio inputs are available, and a total of eightdigital inputs and two outputs make the AVR 347 capable of handling all the latestdigital audio sources. For compatibility with thelatest HDTV video sources and progressive scanDVD players, the AVR also features wide-bandwidth, low-crosstalk component videoswitching.

Coax and optical digital outputs are available fordirect connection to digital recorders. A videorecording output and a color-coded eight-chan-nel input make the AVR 347 virtually future-proof, with everything needed to accommodatetomorrows new formats right on board.

With one simple connection between the AVR 347 and the optional Harman Kardon

, you are able to listen to materialsstored on your compatible Apple iPod**.Your AVRs system remote control has beenpreprogrammed with control codes that enableyou to select tracks for playback and navigatemany of your iPods functions, even from acrossthe room. The Bridge will even let you chargeyour iPod.

The AVR 347s flexibility and power extendbeyond your main home theater or listeningroom. The AVR includes a sophisticated multi-zone control system that allows you to selectone source for use in the main room and adifferent one (Audio only) in a second room.Complete control over volume is possible with aseparate infrared control link. To make it easy tooperate the AVR from a remote room, a separateZone II remote is included.Additional multiroom options include the optionto assign two of the AVRs output channels to themultiroom system and the ability to link the AVRto innovative A-BUS keypads for multiroom oper-ation without the need for external amplifiers.

The AVR 347s powerful amplifier usestraditional Harman Kardon high-current designtechnologies to meet the wide dynamic range ofany program selection.

Harman Kardon invented the high-fidelity receiver more then fifty years ago. With state-of-the-art circuitry and time-honored circuitdesigns, the AVR 347 is the perfect combinationof the latest in digital audio technology, a quietyet powerful analog amplifier in an elegant,easy-to-use package.

**Compatible with all iPod models equipped with a dock connector, including third-generation Click Wheel models and newer. Not compatible withiPod shuffle models. Although iPod photo models are compatible, images stored on the iPod can only be viewed using the controls on the iPod, not withthe AVR remote.

4 SAFETY INFORMATION

Safety Information

Dolby* Digital, Dolby Digital EX andDolby Pro Logic* II and IIx Decoding,and the full suite of DTS modes,including DTS-ES 6.1 Discrete & Matrixand Neo:6

Seven channels of high-current amplifi-cation with two channels assignable toeither surround back or multiroomapplications

Harman Kardons exclusive Logic 7processing, along with a choice ofDolby Virtual Speaker processing foruse when only two speakers areavailable

Dolby Headphone to create spacious,open sound fields when using head-phones

Harman Kardons advanced EzSet/EQautomatically configures speaker set-tings and sets room equalization forquick, easy and accurate system setup

HDMI with audio/video processing,upscaling to 720p, 1080i/1080p pass-through and repeater forincreased cable length without signaldegradation

Two HDMI 1.1 and three assignablehigh-bandwidth analog componentinputs for compatibility with the latesthigh-definition video sources

Front panel analog A/V inputs Front panel digital inputs for easy con-

nection to portable digital devices andthe latest video game consoles

Connects to Harman Kardons (optional) for charging, playback andcontrol of a compatible Apple iPod

device

Input titling for all input sources(except tuner)

Multiple digital inputs and outputs On-screen menu and display system A/V Sync delay adjustable for each

input delivers perfect lip sync withdigital programs or video displays

6-Channel/8-Channel Direct Input forUse with Future Audio Formats

Extensive bass management options,including four separate crossovergroupings

Extensive multiroom options, includinga standard Zone II remote, assignableamplifier channels and A-BUS Ready

capability for listening to a separatesource in a remote zone

Main Remote with Internal Codes

Important Safety Information

READ THIS BEFORE OPERATINGYOUR UNIT.

Do not install this equipment in a confined spacesuch as a case or similar Install it away fromdirect sunlight, heat sources, vibration, dust,moisture, and/or cold.Avoid installing this unit where foreign objectsmay fall onto this unit and/or this unit may beexposed to liquid dripping or splashing. On thetop of this unit, do not place:

Burning objects (i.e. candles), as they maycause fire, damage to this unit, and/orpersonal injury.

Containers with liquid in them, as they mayfall and liquid may cause electrical shock tothe user and/or damage to this unit.

Do not cover this unit with a newspaper, table-cloth, curtain, etc. in order not to obstruct heatradiation. If the temperature inside this unitrises, it may cause fire, damage to this unit,and/or personal injury.

Install this unit near the AC outlet and where theAC power plug can be reached easily.

This unit is not disconnected from the AC powersource as long as it is connected to the wall out-let, even if this unit itself is turned off. This stateis called the standby mode. In this state, this unitis designed to consume a very small quantity ofpower.

WARNINGTO REDUCE THE RISK OF FIRE OR ELECTRICSHOCK, DO NOT EXPOSE THIS APPLIANCETO RAIN OR MOISTURE.

Verify Line Voltage Before Use

Your AVR has been designed for use with 220-240-Volt AC current. Connection to a linevoltage other than that for which it is intendedcan create a safety and fire hazard and maydamage the unit.

If you have any questions about the voltagerequirements for your specific model, or aboutthe line voltage in your area, contact your dealerbefore plugging the unit into a wall outlet.

Do Not Use Extension CordsTo avoid safety hazards, use only the power cordattached to your unit. We do not recommendthat extension cords be used with this product.As with all electrical devices, do not run powercords under rugs or carpets or place heavyobjects on them. Damaged power cords shouldbe replaced immediately by an authorized servicedepot with a cord meeting factory specifications.

Handle the AC Power Cord GentlyWhen disconnecting the power cord from an ACoutlet, always pull the plug, never pull the cord.If you do not intend to use the unit for anyconsiderable length of time, disconnect the plugfrom the AC outlet.

Do Not Open the CabinetThere are no user-serviceable components insidethis product. Opening the cabinet may present ashock hazard, and any modification to the prod-uct will void your guarantee. If water or anymetal object such as a paper clip, wire or astaple accidentally falls inside the unit, discon-nect it from the AC power source immediately,and consult an authorized service station.

SAFETY INFORMATION 5

ENG

LISH

Safety Information

Installation Location To assure proper operation and to avoid the

potential for safety hazards, place the unit ona firm and level surface. When placing theunit on a shelf, be certain that the shelf andany mounting hardware can support theweight of the product.

Make certain that proper space is providedboth above and below the unit for ventilation.If this product will be installed in a cabinet orother enclosed area, make certain that thereis sufficient air movement within the cabinet.Under some circumstances a fan may berequired.

Do not place the unit directly on a carpetedsurface.

Avoid installation in extremely hot or coldlocations, or an area that is exposed to directsunlight or heating equipment.

Avoid moist or humid locations. Do not obstruct the ventilation slots on the

top of the unit, or place objects directly overthem.

Due to the weight of the AVR 347 and the heatgenerated by the amplifiers, there is the remotepossibility that the rubber padding on the bot-tom of the units feet may leave marks on cer-tain wood or veneer materials. Use cautionwhen placing the unit on soft woods or othermaterials that may be damaged by heat orheavy objects. Some surface finishes may beparticularly sensitive to absorbing such marksdue to a variety of factors beyond Harman Kardon's control, including the natureof the finish, cleaning materials used, andnormal heat and vibration caused by the use ofthe product, or other factors. We recommendthat caution be exercised in choosing aninstallation location for the component and innormal maintenance practices, as yourwarranty will not cover this type of damage tofurniture.

CleaningWhen the unit gets dirty, wipe it with a clean,soft, dry cloth. If necessary, wipe it with a softcloth dampened with mild soapy water, then afresh cloth with clean water.Wipe dry immediately with a dry cloth. NEVERuse benzene, aerosol cleaners, thinner, alcohol orany other volatile cleaning agent. Do not useabrasive cleaners, as they may damage the finishof metal parts. Avoid spraying insecticide nearthe unit.

Moving the UnitBefore moving the unit, be certain to disconnectany interconnection cords with other compo-nents, and make certain that you disconnect theunit from the AC outlet.

UnpackingThe carton and shipping materials used to pro-tect your new receiver during shipment werespecially designed to cushion it from shock andvibration. We suggest that you save the cartonand packing materials for use in shipping if youmove, or should the unit ever need repair.

To minimize the size of the carton in storage,you may wish to flatten it. This is done by care-fully slitting the tape seams on the bottom andcollapsing the carton. Other cardboard insertsmay be stored in the same manner. Packingmaterials that cannot be collapsed should besaved along with the carton in a plastic bag.

If you do not wish to save the packagingmaterials, please note that the carton and othersections of the shipping protection are recycla-ble. Please respect the environment and discardthose materials at a local recycling center.

It is important that you remove the protective plas-tic film from the front-panel lens. Leaving the filmin place will affect the performance of your remotecontrol.

6 FRONT PANEL CONTROLS

1 Main Power Switch: Press this button toapply power to the AVR. When the switch ispressed in, the unit is placed in a Standbymode, as indicated by the orange LED 3. Thisbutton MUST be pressed in to operate the unit.To turn the unit off completely and prevent theuse of the remote control, this switch should bepressed until it pops out from the front panel sothat the word OFF may be read at the top ofthe switch.

NOTE: This switch is normally left in the ONposition.

2 System Power Control: When the MainPower Switch 1 is ON, press this button toturn on the AVR; press it again to turn the unitoff (to Standby). Note that the Power Indicator3 will turn blue when the unit is on.

3 Power Indicator: This LED will be illuminatedin orange when the unit is in the Standby modeto signal that the unit is ready to be turned on.When the unit is in operation, the indicator willturn blue.

4 Headphone Jack: This jack may be used tolisten to the AVRs output through a pair of head-phones. Be certain that the headphones have astandard 6.3 mm stereo phone plug. Note thatthe speakers will automatically be turned offwhen the headphones are connected.

When configuring your system using EzSet/EQ,the calibration microphone should be pluggedinto this jack using the supplied adaptor thatconverts the small mini-plug at the end of themicrophones cord to a 1/4" plug.

5 Surround Mode Group Selector: Pressthis button to select the top-level group ofsurround modes. Each press of the button willselect a major mode grouping in the followingorder:

Dolby Modes DTS Digital Modes DSPModes Stereo Modes Logic 7 Modes

Once the button is pressed so that the name ofthe desired surround mode group appears in theMain Information Display , press theSurround Mode Selector 9 to cycle throughthe individual modes available. For example, pressthis button to select Dolby modes, and then pressthe Surround Mode Selector 9 to choosefrom the various mode options.

6 Speaker Select Button: Press this buttonto begin the process of selecting the speakerpositions that are used in your listening room.(See page 31 for more information on setup andconfiguration.)

Front Panel Controls

1234 5 67 8 9 )

! @ # $ % ^ & * (

Main Power SwitchSystem Power ControlPower IndicatorHeadphone JackSurround Mode Group SelectorSpeaker Select ButtonSelector ButtonsTone ModeSurround Mode SelectorTuning

Tuner Band SelectorSet ButtonPreset Stations SelectorSpeaker/Channel Input IndicatorInput Source SelectorRDS Select ButtonDelayDigital Optical 4 InputSurround Mode IndicatorsDigital Coax 4 Input

Video 4 input jacksInput IndicatorsMain Information DisplayRemote Sensor WindowDigital Input SelectorChannel Select ButtonVolume Control

DIGITAL LOGIC 7 VID 1 DVD

CD

FMAM

TAPE6 8 CH

VID 2

VID 3

VID 4

PRO LOGIC

3 STEREO

HEADPHONE

DSP

5 7 CH. STEREO

SURR. OFF

347

Optical 4 Coaxial 4xca

FRONT PANEL CONTROLS 7

ENG

LISH7 Selector Buttons: When you are establishing

the AVRs configuration settings, use these buttonsto select from the choices available, as shown inthe Main Information Display .

8 Tone Mode: Pressing this button enables ordisables the Balance, Bass and Treble tonecontrols. When the button is pressed so that thewords TONEIN appear in the MainInformation Display , the settings of theBass and Treble controls and of the Balancecontrol will affect the output signals. When thebutton is pressed so that the words TONEOUT appear in the Main InformationDisplay , the output signal will be flat,without any balance, bass or treble alteration.

9 Surround Mode Selector: Press this buttonto select from among the available surroundmode options for the mode group selected. Thespecific modes will vary based on the number ofspeakers available, the mode group and if theinput source is digital or analog. For example,press the Surround Mode Group Selector 5to select a mode grouping such as Dolby or Logic7, and then press this button to see the modechoices available. For more information on modeselection, see page 40.

) Tuning Selector: Press the left side of thebutton to tune lower frequency stations and theright side of the button to tune higher frequencystations. When a station with a strong signal isreached, MANUALTUNED or AUTOTUNEDwill appear in the Main InformationDisplay (see page 51 for more informationon tuning stations).

! Tuner Band Selector: Pressing this buttonwill automatically switch the AVR to the Tunermode. Pressing it again will switch between theAM and FM frequency bands, holding it pressedfor some seconds will switch between stereo andmono receiving and between automatic andmanual tuning mode (See page 51 for moreinformation on the tuner).

@ Set Button: When making choices during thesetup and configuration process, press this buttonto enter the desired setting as shown in the Main Information Display into the AVRsmemory.

# Preset Stations Selector: Press thisbutton to scroll up or down through the list ofstations that have been entered into the presetmemory (See page 51 for more information ontuner programming).

$ Speaker/Channel Input Indicators: Theseindicators are multipurpose, indicating either thespeaker type selected for each channel or theincoming data-signal configuration. The left, center,right, right surround and left surround speakerindicators are composed of three boxes, while thesubwoofer is a single box. The center box lightswhen a Small speaker is selected, and the twoouter boxes light when Large speakers areselected. When none of the boxes are lit for thecenter, surround or subwoofer channels, no speakerhas been selected for that position. (See page 31for more information on configuring speakers.) Theletters inside each of the center boxes displayactive input channels. For standard analog inputs,only the L and R will light, indicating a stereoinput. When a digital source is playing, the indica-tors will light to display the channels beingreceived at the digital input. When the lettersflash, the digital input has been interrupted.(See page 44 for more information on the ChannelIndicators).

NOTE: When you have reassigned the surroundback speakers to the remote zone using theMULTIROOMSETUPmenu, the boxes thatindicate the presence of the surround back speak-ers will automatically disappear, reflecting the factthat the main listening area is now configured for5.1-channel operation. (See page 47 for moreinformation on reassigning the surround backspeakers for multiroom use.)

% Input Source Selector: Press this button tochange the input by scrolling through the list ofinput sources.

^ RDS Select Button: Press this button todisplay the various messages that are part of theRDS data system of the AVRs tuner.(See page 52 for more information on RDS).

& Delay: Press this button to begin thesequence of steps required to enter delay timesettings (See page 34 for more information ondelay times).

* Digital Optical 4 Input: Connect theoptical digital audio output of an audio or videoproduct to this jack. When the Input is not in use,be certain to keep the plastic cap installed toavoid dust contamination that might degradefuture performance.

( Surround Mode Indicators: The currentselected mode or function will appear as one ofthese indicators. Note that when the unit isturned on, the entire list of available modes willlight briefly, and then revert to normal operationwith only the active mode indicator illuminated.

Digital Coax 4 Input: This jack is normallyused for connection to the output of portabledigital audio devices, video game consoles orother products that have a coax digital jack.

Video 4 Input Jacks: These audio/videojacks may be used for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio players.

Input indicators: The current selectedmode or function will appear as one of theseindicators. Note that when the unit is turned on,the entire list of available modes will light briefly,and then revert to normal operation with onlythe active mode indicator illuminated.

Main Information Display: This displaydelivers messages and status indications to helpyou operate the receiver.

Remote Sensor Window: The sensorbehind this window receives infrared signals fromthe remote control. Aim the remote at this areaand do not block or cover it unless an externalremote sensor is installed.

Note: When /DMP has been selected as the input source, no Input Indicator willlight. DMP/THEBRIDGEISCONNECTEDwill scroll across the UpperDisplay Line , unless you have retitled thesource name, in which case that name willappear. See page 24 for more information oninput titling.

Digital Input Selector: When playing asource that has a digital output, press this buttonto select between the Optical and Coaxial Digital inputs. (See pages 24 and 41 formore information on digital audio).

Channel Select Button: Press this buttonto begin the process of trimming the channeloutput levels using an external audio source.(For more information on output level trimadjustment, see page 46).

Volume Control: Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR is muted,adjusting volume control will automaticallyrelease the unit from the silenced condition.

Front Panel Controls

8 REAR PANEL CONNECTIONS

Rear Panel Connections

!"#$%&'()*+

AM AntennaFM AntennaTape InputsTape OutputsSubwoofer OutputDVD Audio InputsCD InputsVideo 1 Audio Outputs

DMP Connector8-Channel Direct InputsDigital Audio OutputsVideo Monitor OutputsDVD Video InputsFront Speaker OutputsCenter Speaker Outputs

Surround Speaker OutputsSwitched AC Accessory OutletRS-232 Serial PortAC Power CordVideo 2 Component Video InputsComponent Video OutputsVideo 1 Component Video InputsVideo 2 Audio InputsCoaxial Digital InputsSurround Back/Multiroom Speaker OutputsVideo 1 Video OutputsVideo 1 Video InputsOptical Digital InputsVideo 1 Audio InputsVideo 2 Video Inputs

Remote IR OutputRemote IR InputPreamp OutputsHDMI OutputVideo 3 Video InputsVideo 3 Audio InputsHDMI InputsMultiroom OutputsA-BUS ConnectorMultiroom IR InputDVD/Video 3 Component Video InputsRemote IR Carrier Output

NOTE: To assist in making the correct connec-tions for multichannel input/output and speakerconnections, all connection jacks and terminalshave been color coded in conformance with thelatest CEA standards as follows:Front Left: WhiteFront Right: RedCenter: GreenSurround Left: BlueSurround Right: GraySurround Back Left: BrownSurround Back Right: TanSubwoofer (LFE): PurpleDigital Audio: OrangeComposite Video: YellowComponent Video Y: GreenComponent Video Pr: RedComponent Video Pb: Blue

AM Antenna: Connect the AM loop antennasupplied with the receiver to these terminals. If anexternal AM antenna is used, make connections tothe AM and GND terminals in accordance withthe instructions supplied with the antenna.

FM Antenna: Connect the supplied indoor oran optional external FM antenna to this terminal.

Tape Inputs: Connect these jacks to thePLAY/OUT jacks of an audio recorder.

Tape Outputs: Connect these jacks to theRECORD/INPUT jacks of an audio recorder.

Subwoofer Output: Connect this jack tothe line-level input of a powered subwoofer. If anexternal subwoofer amplifier is used, connect thisjack to the subwoofer amplifier input.

DVD Audio Inputs: Connect these jacks tothe analog audio jacks on a DVD or other audioor video source.

CD Inputs: Connect these jacks to the analog output of a compact disc player or CDchanger or any other audio source.

Video 1 Audio Outputs: Connect thesejacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.

Digital Media Player (DMP)Connector: With the AVR 347 turned off, con-nect one end of the optional Harman Kardon

to this proprietary connector, and theother to your compatible Apple iPod. When theDigital Media Player source is selected, you mayview your iPods control and navigation mes-sages on your video display (if one is connectedto one of the Video Monitor Outputs), andin the Upper and Lower Display Lines .You may navigate the iPod and select tracks forplayback using the /// ButtonsDE, the Set ButtonF andTransport ControlsP on your AVR remote.See page 45 for more information.

REAR PANEL CONNECTIONS 9

ENG

LISH

Rear Panel Connections

8-Channel Direct Inputs: These jacks areused for connection to source devices such asDVD-Audio, Blu-ray, HD-DVD or SACD playerswith discrete analog outputs. Depending on thesource device in use, all eight jacks may be used,though in many cases only connections to thefront left/right, center, surround left/right andLFE (subwoofer input) jacks will be used forstandard 5.1 audio signals.

Digital Audio Outputs: Connect thesejacks to the matching digital input connector ona digital recorder such as a CD-R or MiniDiscrecorder.

Video Monitor Outputs: Connect this jackto the composite and/or S-Video input of a TVmonitor or video projector to view the on-screenmenus and the output of any standard Video orS-Video source selected by the receivers videoswitcher.

DVD Video Inputs: Connect these jacks tothe composite or S-Video output jacks on a DVDplayer or other video source.

Front Speaker Outputs: Connect theseoutputs to the matching + or terminals onyour left and right speakers. In conformance withthe new CEA color code specification, the Whiteterminal is the positive, or "+" terminal thatshould be connected to the red (+) terminal onFront Left speaker with the older color coding,while the Red terminal is the positive, or "+"terminal that should be connected to the red (+)terminal on Front Right speaker. Connect theblack () terminals on the AVR to the black ()terminals on the speakers. See page 17 for moreinformation on speaker polarity.

Center Speaker Outputs: Connect theseoutputs to the matching + and terminals onyour center channel speaker. In conformancewith the new CEA color code specification, theGreen Terminal is the positive, or "+" terminalthat should be connected to the red (+) terminalon speakers with the older color coding. Connectthe black () terminal on the AVR to the blacknegative () terminal on your speaker. (See page17 for more information on speaker polarity.)

Surround Speaker Outputs: Connectthese outputs to the matching + and terminalson your surround channel speakers. In confor-mance with the new CEA color code specifica-tion, the Blue terminal is the positive, or "+"terminal that should be connected to the red (+)terminal on the Surround Left speaker with oldercolor coding, while the Gray terminal should beconnected to the red (+) terminal on theSurround Right speaker with the older colorcoding. Connect the black () terminal on theAVR to the matching black negative () terminals for each surround speaker. (See page17 for more information on speaker polarity.)

Switched AC Accessory Outlet: Thisoutlet may be used to power any device that youwish to have turn on when the AVR is turned onwith the System Power Control switch 2.

RS-232 Serial Port: This specializedconnector may be used with your personalcomputer in case Harman Kardon offers a soft-ware upgrade for the receiver at some time inthe future. Leave the Mode switch popped out inthe Operate position, unless the AVR 347 isbeing upgraded. The Reset switch is used onlyduring the upgrade process.

AC Power Cord: Connect the AC plug to anunswitched AC wall output.

Video 2 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofan HDTV Set-top convertor, satellite receiver, orother video source device with component videooutputs to these jacks. The factory default is forthese jacks to be a linked to the Video 1 input,but you may change the setting at any timethrough the INPUTSETUPmenu. See page24 for more information on configuring the com-ponent video inputs.

Monitor Component Video Outputs:Connect these outputs to the component videoinputs of a video projector or monitor. When asource connected to one of the threeComponent Video Inputs* is selectedthe signal will be sent to these jacks.

Video 1 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofa DVD player to these jacks. The factory defaultis for these jacks to be a linked to the DVDinput, but you may change the setting at anytime through the INPUTSETUPmenu. Seepage 24 for more information on configuring thecomponent video inputs.

Note: All component inputs/outputs can beused for RGB signals too, in the same way asdescribed for the Y/Pr/Pb signals, then connectedto the jacks with the corresponding color.RGB connection is not possible if the source out-puts a separate sync signal (see page 18).

Video 2 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a second VCRor other audio or video source.

Coaxial Digital Inputs: Connect the coaxdigital output from a DVD player, HDTV receiver,the output of a compatible computer sound cardplaying MP3 files or streams, LD player, MDplayer or CD player to these jacks. The signalmay be either a Dolby Digital signal, DTS signal,a 2 channel MPEG 1 signal, or a standard PCMdigital source. Do not connect the RF digital out-put of an LD player to these jacks.

Surround Back/Multiroom SpeakerOutputs: These speaker terminals are normallyused to power the surround back left/surroundback right speakers in a 7.1 channel system.However, they may also be used to power thespeakers in a second zone, which will receive theoutput selected for a multiroom system.To change the output fed to these terminalsfrom the default of the Surround Back speakersto the Multiroom Output, you must change asetting in the MULTIROOMMENU of theOSD system. See page 47 for more informationon configuring this speaker output. In normalsurround system use, the brown and black termi-nals are the surround back left channel positive(+) and negative () connections and the tanand black terminals are the surround back rightpositive (+) and negative () terminals.For multiroom use, connect the brown and blackSBL terminals to the red and black connectionson the left remote zone speaker and connect thetan and black SBR terminals to the red and blackterminals on the right remote zone speaker.

Video 1 Video Outputs: Connect thesejacks to the RECORD/INPUT composite or S-Video jack on a VCR.

Video 1 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona TV or other video source.

Optical Digital Inputs: Connect the optical digital output from a DVD player, HDTVreceiver, the output of a compatible computersound card playing MP3 files or streams, LDplayer, MD player or CD player to these jacks.The signal may be either a Dolby Digital signal, aDTS signal, a 2 channel MPEG 1 signal, or astandard PCM digital source.

Video 1 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a TV or otheraudio or video source.

Video 2 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona second VCR or other video source.

10 REAR PANEL CONNECTIONS

Rear Panel Connections

Remote IR Output: This connection per-mits the IR sensor in the receiver to serve otherremote controlled devices. Connect this jack tothe IR IN jack on Harman Kardon or othercompatible equipment.

! Remote IR Input: If the AVRs front-panelIR sensor is blocked due to cabinet doors orother obstructions, an external IR sensor maybe used. Connect the output of the sensor tothis jack.

" Preamp Outputs: Connect these jacks toan optional, external power amplifier for appli-cations where higher power is desired.

# HDMI Output: Connect this jack to theHDMI input on a compatible HDMI-equippedvideo display.

$ Video 3 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks onany video source.

% Video 3 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on any audio orvideo source.

& HDMI Inputs: Connect the HDMI output ofvideo sources such as a DVD player, set-top boxor HDTV tuner to either of these jacks.

' Multiroom Outputs: Connect these jacksto an optional audio power amplifier to listen tothe source selected by the multiroom system in aremote room.

( A-BUS Connector: Connect this jack to anoptional A-BUS-certified remote room keypad oramplifier to extend the multiroom capabilities ofyour AVR. See page 21 for more information onA-BUS.

)Multiroom IR Input: Connect the output ofan IR sensor in a remote room to this jack tooperate the AVRs multiroom control system.

* Video 3 Component Video Inputs: Theseinputs may be used with any source deviceequipped with analog Y/Pr/Pb or RGB compo-nent video outputs. The factory default is forthese jacks to be a linked to the Video 2 input,but you may change the setting at any timethrough the INPUTSETUPmenu. See page24 for more information on configuring thecomponent video inputs.

+ Remote IR Carrier Output: The output ofthis jack is the full signal received at theRemote Sensor Window or input throughthe Remote IR Input! including the carrierfrequency that is removed from signals at theRemote IR Output . Use this output toextend IR remote signals to the input ofcompatible products by direct connection orthrough the use of optional, external IRblasters. If you are in doubt as to which of thetwo IR Output jacks to use, we recommend thatyou consult with your dealer or installer, or checkwith the manufacturer of the external equipmentyou wish to control.

With the AVRs powerful processor, you may con-nect up to two HDMI-equipped source devices tothe HDMI inputs using a single-cable connec-tion, while benefiting from superior digital audioand video performance. However, if your videodisplay is not HDMI-compatible, you will need toconnect the source device to one of the othersource inputs, selecting a coaxial or optical digi-tal audio input and analog video input. See theConnections and Installation sections for moreinformation.

If your video display has an HDMI input, butsome of your sources have only analog videooutputs, you may still rely on just the HDMIvideo connection to your display; the AVR willautomatically transcode analog video signals tothe HDMI format.

NOTE ON VIDEO CONNECTIONS: When con-necting a video source product such as a VCR,DVD player, satellite receiver, cable set-top box,personal video recorder or video game to theAVR 347, you may use either a composite or S-video connection, but not both.

MAIN REMOTE CONTROL FUNCTIONS 11

ENG

LISH

Main Remote Control Functions

0123456789ABCDEFGHIJKLMNOPQ

Power Off ButtonIR Transmitter WindowProgram IndicatorPower On ButtonInput SelectorsAVR SelectorAM/FM Tuner Select6-Channel/8-Channel Direct InputTest ButtonSleep ButtonSurround Mode SelectorNight ModeChannel Select Button / Buttons ButtonSet ButtonDigital SelectNumeric KeysTuner ModeDirect ButtonTuning Up/DownOSD ButtonDolby Mode Select ButtonDTS Digital Mode SelectorLogic 7 Mode Select ButtonTransport ControlsMultiroomSkip Up/Down ButtonsStereo Mode Select ButtonDTS Neo:6 Mode SelectMacro ButtonsRDS Selector ButtonPreset Up/DownClear ButtonMemory ButtonDelay/Prev. Ch. ButtonSpeaker SelectMuteVolume Up/Down

DMP SelectorTV/Video SelectorDim ButtonLearn ButtonLight ButtonTone Mode

NOTE: The function names shown here are eachbuttons feature when used with the AVR. Mostbuttons have additional functions when usedwith other devices. See page 58-59 for a list ofthese functions.

347

12 MAIN REMOTE CONTROL FUNCTIONS

Main Remote Control Functions

IMPORTANT NOTE: The AVR 347s remote maybe programmed to control up to seven devices,including the AVR. Before using the remote, it isimportant to remember to press the InputSelector button 4 that corresponds to theunit you wish to operate. In addition, the AVRsremote is shipped from the factory to operatethe AVR and most Harman Kardon CD or DVDplayers and cassette decks. The remote is alsocapable of operating a wide variety of otherproducts using the control codes that are part ofthe remote. Before using the remote with otherproducts, follow the instructions on pages 53-55to program the proper codes for the products inyour system.

It is also important to remember that many ofthe buttons on the remote take on different functions, depending on the product selectedusing the Input Selector Button4. Thedescriptions shown here primarily detail thefunctions of the remote when it is used to operatethe AVR. (See page 58-59 for information aboutalternate functions for the remotes buttons.)

0 Power Off Button: Press this button toplace the AVR or a selected device unit in theStandby mode.

1 IR Transmitter Window: Point this windowtowards the AVR when pressing buttons on theremote to make certain that infrared commandsare properly received.

2 Program Indicator: This three-colorindicator is used to guide you through theprocess of programming the remote. (See page53 for information on programming the remote.)

3 Power On Button: Press this button toturn on the power to a device selected by pressingone of the Input Selectors4 (except Tape).

4 Input Selectors: Pressing one of thesebuttons will perform three actions at the sametime. First, if the AVR is not turned on, this willpower up the unit. Next, it will select the sourceshown on the button as the input to the AVR.Finally, it will change the remote control so thatit controls the device selected.

The buttons labeled DVD, TAPE and HDMI 1 areeach used to select either of two input sources:

The first press of the DVD Button selects thecomponent connected to the DVD inputs.A second press of this button selects thecomponent connected to the CD inputs.

The first press of the button labeled TAPEselects Tape as the input. A second press of thisbutton selects the The Bridge as an input.

The first press of the HDMI 1 button selectsthe device that is connected to the HDMI 1 jack.A second press selects the device connected tothe HDMI 2 jack.

After pressing one of these buttons you mustpress the AVR Selector button5 again tooperate the AVRs functions with the remote.

5 AVR Selector: Pressing this button willswitch the remote so that it will operate theAVRs functions. If the AVR is in the Standbymode, it will also turn the AVR on.

6 AM/FM Tuner Select: Press this button toselect the AVRs tuner as the listening choice.Pressing this button when the tuner is in use willselect between the AM and FM bands.

7 6-Channel/8 Channel Direct Input:Press this button to select the device connectedto the 6-Channel Direct Inputs or the 8-Channel Direct Inputs (the input available will depend on the selection 5.1 or6.1/7.1 made in the surround mode setting,see page 40 for more information).

8 Test Tone: Press this button to begin thesequence used to calibrate the AVRs outputlevels. (See page 35 for more information oncalibrating the AVR).

9 Sleep Button: Press this button to placethe unit in the Sleep mode. After the time shownin the display, the AVR will automatically go intothe Standby mode. Each press of the buttonchanges the time until turn-off in the followingorder:

Hold the button pressed for two seconds to turnoff the Sleep mode setting.Note that this button is also used to changechannels on your TV, VCR and Sat receiver whenthe appropriate source is selected, using thedevice Input Selectors4.

A Surround Mode Selector: Press this but-ton to select any of the HALL, THEATER surroundmodes. Note that depending on the type ofinput, some modes are not always available.(See page 37-38 for more information aboutsurround modes.) Note that this button is alsoused to tune channels on your TV, VCR and Satreceiver when the appropriate source is selectedusing the device Input Selector4.

B Night Mode: Press this button to activatethe Night mode. This mode is available only withDolby Digital encoded sources, and it preservesdialog (center channel) intelligibilty at lowvolume levels (See page 27 for moreinformation).

C Channel Select Button: This button isused to start the process of setting the AVRsoutput levels with an external source. Once thisbutton is pressed, use the / buttons D toselect the channel being adjusted, then press theSet button F, followed by the / buttonsD again, to change the level setting.(See page 46 for more information.)

D/ Buttons: These multipurpose but-tons are used to change or scroll through itemsin the on-screen menus or on the front panel orto make configuration settings such as digitalinputs or delay timing. When changing a setting,first press the button for the function or settingto be changed (e.g., press the Digital SelectButtonG to change a digital input) and thenpress one of these buttons to scroll through thelist of options or to increase or decrease a set-ting. The sections in this manual describing theindividual features and functions contain specificinforma-tion on using these buttons for eachapplication.

When the AVR remote is being programmed forthe codes of another device, these buttons arealso used in the Auto Search process (Seepage 53 for more information on programmingthe remote.)

MAIN REMOTE CONTROL FUNCTIONS 13

ENG

LISH

Main Remote Control Functions

E Button: This button is used to changethe menu selection or setting during some of thesetup procedures for the AVR.

F Set Button: This button is used to enter settings into the AVRs memory. It is also used inthe setup procedures for delay time, speakerconfiguration and channel output level adjust-ment.

G Digital Select: Press this button to assignone of the digital inputs * to a source.(See page 41 for more information on using digital inputs.)

H Numeric Keys: These buttons serve as aten-button numeric keypad to enter tuner presetpositions. They are also used to select channelnumbers when TV, VCR or Sat receiver hasbeen selected on the remote, or to select tracknumbers on a CD, DVD or LD player, dependingon how the remote has been programmed.

I Tuner Mode: Press this button when thetuner is in use to select between automatictuning and manual tuning. When the button ispressed so MANUAL appears in the MainInformation Display , pressing the Tuningbuttons K) will move the frequency up ordown in single-step increments. When the FMband is in use and AUTO appears in theMain Information Display , pressing thisbutton will change to monaural receptionmaking even week stations audible. (See page51 for more information.)

J Direct Button: Press this button when thetuner is in use to start the sequence for directentry of a stations frequency. After pressing thebutton simply press the proper Numeric KeysH to select a station (See page 51 for moreinformation on the tuner).

K Tuning Up/Down: When the tuner is inuse, these buttons will tune up or down throughthe selected frequency band. If the Tuner Modebutton I has been pressed or the Band but-ton ! on the front panel was held pressed sothat AUTO appears in the MainInformation Display , pressing either ofthe buttons will cause the tuner to seek the nextstation with acceptable signal strength forquality reception. When the MANUAL appearsin the Main Information Display ,pressing these buttons will tune stations insingle-step increments. (See page 51 for moreinformation.)

L OSD Button: Press this button to activatethe On Screen Display (OSD) system used to setup or adjust the AVRs parameters.

M Dolby Mode Selector: This button isused to select one of the available DolbySurround processing modes. Each press of thisbutton will select one of the Dolby Pro Logic IImodes, Dolby 3 Stereo or Dolby Digital. Notethat the Dolby Digital mode is only availablewith a digital input selected and the othermodes only as long as a Dolby Digital source isnot playing (except Pro Logic II with DolbyDigital 2.0 recordings, see page 37-38). Seepage 37 for the available Dolby surround modeoptions.

N DTS Digital Mode Selector: When a DTSsource is in use the AVR will select the appropri-ate mode automatically and no other mode willbe available. Pressing this button will display themode currently selected by the AVRs decoder,depending on the surround material played andthe speaker setting. When a DTS source is not inuse, this button has no function. (See page 37for the available DTS options.)

O Logic 7 Selector: Press this button toselect one of the available Logic 7 surroundmodes. (See page 37-38 for the available Logic 7 options.)

P Transport Control Buttons: These but-tons do not have any functions for the AVR, butthey may be programmed for theforward/reverse play operation of a wide varietyof CD or DVD players, and audio or video- cas-sette recorders. (See page 53 for more informa-tion on programming the remote.)

QMulti-Room: Press this button to activatethe Multiroom system or to begin the process ofchanging the input or volume level for the sec-ond zone. (See page 47 for more information onthe Multiroom system.)

Skip Up/Down Buttons: These buttonsdo not have a direct function with the AVR, butwhen used with a compatibly programmed CDor DVD player/changer they will change thetracks on the disc currently being played.

Stereo Mode Selector: Press this buttonto select a stereo playback mode. When the but-ton is pressed so that SURROUNDOFFappears in the Main Information Display ,with only the Surr Off Surround ModeIndicator ( lit, the AVR will operate in abypass mode with true fully analog, two-channelleft/right stereo mode with no surround process-ing or bass management as opposed to othermodes where digital processing is used. Whenthe button is pressed so that SURROUNDOFF appears in the Main InformationDisplay , with both the DSP and Surr OffSurround Mode Indicators ( lit, you mayenjoy a two-channel presentation of the soundalong with the benefits of bass management.When the button is pressed so that 5 CHSTEREO or 7 CHSTEREO appears, thestereo signal is routed to all five speakers, ifinstalled. (See page 28 for more information onstereo playback modes).

DTS Neo:6 Mode Selector: Pressing thisselector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-,six- or seven-channel surround field from two-channel program material (from PCMsource or analog input signal). The first pressselects the last DTS Neo:6 surround mode thatwas in use, and each subsequent press selectsthe next mode.

Macro Buttons: Press these buttons tostore or recall a Macro, which is a pre-pro-grammed sequence of commands stored in theremote. (See page 55 for more information onstoring and recalling macros).

RDS Select Button: Press this button todisplay the various messages that are part of theRDS data system of the AVRs tuner. (See page52 for more information on RDS).

Preset Up/Down: When the tuner is inuse, press these buttons to scroll through thestations programmed into the AVRs memory.When CD or DVD is selected using the InputSelector button 4, these buttons mayfunction as Slow Fwd/Rev (DVD) or +10 (CD,CDR).

Clear Button: Press this button to clearincorrect entries when using the remote todirectly enter a radio stations frequency.

14 MAIN REMOTE CONTROL FUNCTIONS

Main Remote Control Functions

Memory Button: Press this button toenter a radio station into the AVR s presetmemory. Two underline indicators will flash atthe right side of the Main InformationDisplay , you then have five seconds toenter a preset memory location using theNumeric KeysH. (See page 51 for moreinformation).

Delay/Prev Ch.: Press this button to beginthe process for setting the delay times used bythe AVR when processing surround sound. Afterpressing this button, the delay times are enteredby pressing the Set button F and then usingthe / buttons D to change the setting.Press the Set button again to complete theprocess. (See page 34 for more information).

Button: Press this button to change asetting or selection when configuring many ofthe AVRs settings.

Speaker Select: Press this button to beginthe process of configuring the AVRs BassManagement System for use with the type ofspeakers used in your system. Once the buttonhas been pressed, use the / buttons D toselect the channel you wish to set up.Press the Set ButtonF and then select thespeaker type (Large, Small or None) appropriatewith the speaker in use. (See page 31 for moreinformation).

Mute: Press this button to momentarilysilence the AVR or TV set being controlled,depending on which device has been selected.When the AVR remote is being programmed tooperate another device, this button is pressedwith the Input Selector button 4 to beginthe programming process. (See page 53 for moreinformation on programming the remote).

Volume Up/Down: Press these buttons toraise or lower the system volume.

Digital Media Player (DMP)Selector: When Harman Kardons (optional) is connected to DigitalMedia Player (DMP) Connector and acompatible Apple iPod is docked in ,pressing this selector will select the iPod as theaudio source input device for the AVR 347. Inaddition, if a video display is connected to oneof the Video Monitor Outputs, the iPodsmessages will appear on screen, and in theUpper and Lower Display Lines . The// / ButtonsDE, the SetButtonF and the Transport ControlsPmay be used to navigate the iPod and to operatemany functions. See page 45, and the manualsfor The Bridge and your iPod for more information.

TV/Video Button: This button does nothave a direct function on the AVR, but whenused with a compatibly programmed VCR, DVDor satellite receiver that has a TV/Video func-tion, pressing this button will switch betweenthe output of the player or receiver and theexternal video input to that player. Consult theOwners Manual for your specific player orreceiver for the details of how it implements thisfunction.

NOTE: With the press of any remote button theInput Selector button45 associatedwith the botton pressed will briefly flash red toconfirm the transmission of the command, aslong as there is a function for that button withthe device selected (see function list on pages 58-59).

Dim Button: Press this button to activatethe Dimmer function, which reduces the bright-ness of the front-panel display, or turns it offentirely. The first press of the button shows thedefault state. Press the button again to changethe display to reduce the brightness by 50%,and press it again within five seconds and themain display will go completely dark. Note thatthis setting is temporary; regardless of anychanges, the display will always return to fullbrightness when the AVR is turned on. The blueillumination around the Power Indicator 3will always remain at full brightness regardlessof the setting to remind you that the AVR is stillturned on.

Learn Button: The remote control iscapable of "learning" individual IR codes fromthe original remote control that came with yourTV or other device that is connected to any ofthe source inputs. (See page 54 for moreinformation).

Light Button: Press this button toilluminate the buttons on the remote control.Press it again to turn the backlight off, or waitfor five seconds after the last button press forthe light to turn off on its own.

Tone Mode : Pressing this button enablesor disables the Balance, Bass and Treble tonecontrols. When the button is pressed so that thewords TONEIN appear in the MainInformation Display , the settings of theBass and Treble controls and of the Balancecontrol will affect the output signals. When thebutton is pressed so that the words TONEOUT appear in the Main InformationDisplay , the output signal will be "flat",without any balance, bass or treble alteration.

ZONE II REMOTE CONTROL FUNCTIONS 15

ENG

LISH

Zone II.2 Remote Control Functions

K

D

J

G

H

I

F

CC

BB

E

A

A Power OffB AVR SelectorC AM/FM Tuner SelectD Input SelectorsE Disc SkipF Volume Up/DownG MuteH Transport ControlsI /DMP SelectorJ Tuning Up/DownK Preset Up/Down

NOTE: The Zone II.2 remote may be used ineither the same room where the AVR is located,or it may be used in a separate room with anoptional infrared sensor that is connected to theAVRs Multi IR input jack ). When it is used inthe same room as the AVR, it will control thefunctions of the AVR or any compatible Harman Kardon products in that room. When itis used in a separate room via a sensorconnected to the Multi IR Jack ), the buttonsfor power, input source, volume and mute willcontrol the source and volume for the secondzone, as connected to the Multi Out Jacks '.(See page 47 for complete information on usingthe Multiroom system.)

The Zone II remote may be used in either thesame room where the AVR is located, or it maybe used in a separate room with an optionalinfrared sensor that is connected to the AVRsMulti IR input jack ) or an A-BUS device.

A Power Off: When used in the room wherethe AVR is located, press this button to place theunit in Standby. When it is used in a remoteroom with a sensor that is connected to theMulti IR jack ), this button turns the Multi-Room system off.

B AVR Selector: Press this button to turn onthe AVR. The input in use when the unit was laston will be selected.

C AM/FM Tuner Select: Press this button toselect the Tuner as the input to the Multiroomsystem. Press it again to change between theAM and FM bands.

D Input Selectors: When the AVR is off,press one of these buttons to turn the unit onand to select a specific input. When the unit isalready in use, pressing one of these buttons willchange the input.

E Disc Skip: Press this button to changediscs on compatible Harman Kardon CD or DVDchangers.

F Volume Up/Down: When used in theroom where the AVR is located, press this buttonto raise or lower the volume in that room. Whenit is used in a remote room with a sensor that isconnected to the Multi IR Jack ), this buttonwill raise or lower the volume in the remoteroom.

G Mute: When used in the room where theAVR is located, press this button to temporarilysilence the unit. When it is used in a remoteroom with a sensor that is connected to theMulti IR Jack ), this button will temporarilysilence the feed to the remote room only. Pressthe button again to return to the previousvolume level.

Important Note: No matter in which room theZone II remote is used, as with the main remoteit is important to remember to press the InputSelector button D that corresponds to theunit you wish to operate befor you change thedevice to be controlled.

H Transport Control Buttons: Thesebuttons do not have any functions for the AVR,but they are programmed for the forward/reverse play operation of a wide variety ofHarman Kardon CD or DVD players, and audio orvideo- cassette recorders.

16 ZONE II REMOTE CONTROL FUNCTIONS

Zone II.2 Remote Control Functions

I Digital Media Player (DMP)Selector: When Harman Kardons (optional) is connected to DigitalMedia Player (DMP) Connector and acompatible Apple iPod is docked in ,pressing this selector will select the iPod as theaudio source input device for the AVR 347. Inaddition, if a video display is connected to oneof the Video Monitor Outputs, the iPodsmessages will appear on screen, and in theUpper and Lower Display Lines . The/// ButtonsDE, the SetButtonF and the Transport ControlsPmay be used to navigate the iPod and to operatemany functions. See page 45, and the manualsfor The Bridge and your iPod for more informa-tion.

J Tuning Up/Down: When the tuner is inuse, these buttons will tune up or down throughthe selected frequency band. If the Tuner Modebutton I has been pressed or the Band but-ton ! on the front panel was held pressed sothat AUTO appears in the MainInformation Display , pressing either ofthe buttons will cause the tuner to seek the nextstation with acceptable signal strength forquality reception. When the MANUAL appearsin the Main Information Display ,pressing these buttons will tune stations insingle-step increments. (See page 51 for moreinformation.)

K Preset Up/Down: When the tuner is inuse, press these buttons to scroll through thestations programmed into the AVRs memory.When CD or DVD is selected using the InputSelector button 4, these buttons mayfunction as Slow Fwd/Rev (DVD) or +10 (CD,CDR).

INSTALLATION AND CONNECTIONS 17

ENG

LISHAfter unpacking the unit, and placing it on a solid

surface capable of supporting its weight, you willneed to make the connections to your audio andvideo equipment.

Audio Equipment Connections

There are two formats for audio connections:digital and analog. Digital audio signals are ofhigher quality, and are required for listening tosources encoded with digital surround modes,such as Dolby Digital and DTS. There are threetypes of digital audio connections: HDMI, coaxialand optical. Any one type of digital audioconnection may be used for each source device,but never more than one for the same source.However, its okay to make both analog anddigital audio connections at the same time tothe same source.

Since the AVR is capable of processing the audioand video portions of an HDMI signal, if yourvideo display device has an HDMI input, youmay make a single HDMI connection from yoursource device (such as a DVD player) to the AVR.In that case no separate digital audio connectionis required.

We recommend that you use high-quality inter-connect cables when making connections tosource equipment and recorders to preserve theintegrity of the signals.

When making connections to audio sourceequipment or speakers it is always a good practice to unplug the unit from the AC wall outlet. This prevents any possibility ofaccidentally sending audio or transient signals tothe speakers that may damage them.

HDMI Connections

HDMI is the abbreviation for High-DefinitionMultimedia Interface, which is quickly becomingthe standard connection point betweenadvanced video/audio source products anddisplays, particularly for high-definition videosignals. HDMI is a digital connection, eliminatingthe need to convert signals back and forth fromdigital to analog to deliver a higher qualitysignal when used with digital sources. Thesignals carried on HDMI may, but do not always,include audio, offering the possibility of acomplete one-wire connection from a source tothe AVR. However, it is important to note thatthere are a number of different versions of theHDMI standard in use. Before connecting anyHDMI products to your AVR, it is helpful to findout in advance their level of HDMI connectivity.

Some source or display components in yoursystem may use DVI (Digital Video Interface) fordigital video connections. DVI carries the samedigital video signals as HDMI but uses a largerconnector and does not transport audio orcontrol signals. In most cases, you may mix andmatch DVI and HDMI digital video connectionsby using optional connector adapters. Note,however, that some DVI-equipped video displaysare not compatible with the HDCP copy protec-tion coding that is increasingly carried withsignals connected via HDMI. If you have anHDMI source and a DVI-equipped display, youmay occasionally be unable to view a program ifthe display does not include HDCP. This is notthe fault of the AVR or your source; it simplyindicates that the video display is not compatible.

HDMI Input Connections

The different Version levels of HDMI definewhich type of audio signals it is compatible with.Based on the lowest level of HDMI among yoursources, the connections to the AVR should bemade as follows:

HDMI 1.0 sources carry digital video andmultichannel or 2-channel PCM audio signalsonly. Connect the HDMI output of a 1.0 sourceto either of the HDMI Inputs& on the AVR.If the product is a DVD-Audio player or othersource that has multichannel analog audiooutputs, connect them to the 8-ChannelDirect Inputs. With an HDMI 1.0 source,particularly a DVD player, make certain that the menus in the source device are set toBitstream Out or Original so that 5.1digital audio is available. If you find that 5.1Dolby Digital or DTS audio is not available onthe HDMI connection, it will be necessary tomake an additional connection between thesource and the AVR 347 to either the Coaxial or Optical* Digital Inputs.

HDMI 1.1 sources carry the multichanneldigital audio output from DVD-Audio playersin addition to the digital video. If you have anHDMI 1.1-equipped product, the only connec-tion needed for listening in the main room isfrom the HDMI output of the source to eitherof the HDMI Inputs& on the AVR. If theplayer has SACD, HD-DVD or Blu-raycapability, you will need to connect the analogoutputs of the source to the 8-ChannelDirect Inputs.

HDMI 1.2 (and higher) sources should beconnected as shown above for HDMI 1.1,except that a separate analog connection isnot needed for SACD players.

In addition, the AVR will convert analog videosignals to the HDMI format, upscaling to high-definition 720p resolution. Source signals with1080i or 1080p resolution are passed throughto your display at their original high-qualityresolution, depending on your displays capabili-ties. You may view the AVRs own on-screendisplay menus using the HDMI output.

HDMI cable runs are usually limited to about 3 meters. The AVR incorporates a repeater, whichallows an additional 3 meters of cable betweenthe source device and the video display.

If your video display or source device is notHDMI-capable, you will need to use either acoaxial or optical digital audio connection andone of the analog video connections (composite,S- or component video), if available, as describedin the next paragraphs.

It is not possible to feed an analog compositeor S-video signal to a recorder or the AVRsmultizone system when an HDMI input is inuse. If an HDMI-equipped source also has ana-log audio and video outputs, connect them tothe Video 2 or Video 3 Video$ andAudio% on the AVR.

In some instances, HDMI-equipped sourceswill not permit more than one video output ata time, and thus you cannot use the samesource in the main listening room and with therecorder or remote zone at the same time. Thisis not a fault of the AVR, but rather a functionof the content protection systems that are partof the HDMI standard.

HDMI Output Connections

Connect the HDMI Output# to an HDMIinput on your video display. Thanks to the AVR 347s video processing system, all videoinput signals are converted to an HDMI output,so only one connection is required between theAVR and your display.

Analog and Digital Input Connections1. Connect the analog output of a CD player tothe CD inputs .

NOTE: When the CD player has both fixed andvariable audio outputs it is best to use the fixedoutput unless you find that the input to thereceiver is so low that the sound is noisy, or sohigh that the signal is distorted.

2. Connect the analog Play/Out jacks of a cas-sette deck, MD, CD-R or other audio recorder tothe Tape Input jacks . Connect the analogRecord/In jacks on the recorder to the TapeOutput jacks on the AVR.

Installation and Connections

18 INSTALLATION AND CONNECTIONS

3. Connect the digital output of any digitalsources such as a CD or DVD changer or player,advanced video game, a digital satellite receiver,HDTV tuner or digital cable set-top box or theoutput of a compatible computer sound card tothe Optical and Coaxial Digital Inputs*.We recommend connecting the coaxial digitalaudio output of your DVD player to the Coax 1Digital Audio Input, since that digital inputis assigned to the DVD source by default.

The Video 2/Cable/Sat source defaults to theOptical 1 Digital Audio Input. If yourcable television set-top box or satellite receiveris equipped with an optical digital audio output,we recommend that you connect it to this inputto obtain the benefits of higher-quality digitalaudio (such as PCM, Dolby Digital 2.0 or DolbyDigital 5.1 signals when broadcast by your cableor satellite provider).

NOTE: If you wish for your digital source deviceto be available for use by the multiroom system,you will need to connect its analog audiooutputs to the appropriate inputs on the AVR 347, as the multiroom system is notcapable of distributing digital signals to theremote zone.

4. Connect the Coaxial or Optical DigitalOutputs on the rear panel of the AVR to thematching digital input connections on a CD-R orMiniDisc recorder.

5. Assemble the AM Loop Antenna supplied withthe unit as shown below. Connect it to the AMand GND screw terminals .

6. Connect the supplied FM antenna to the FM(75 ohm) connection . The FM antenna maybe an external roof antenna, an inside poweredor wire lead antenna or a connection from acable system. Note that if the antenna orconnection uses 300-ohm twin-lead cable, youshould use a 300-ohm-to-75-ohm adapter tomake the connection.

7. With the AVR 347 turned off, connect theoptional Harman Kardon to Digital Media Player (DMP) Connector.Your compatible Apple iPod may be docked in

when you wish to use it as your audiosource device.

8. Connect the front, center and surroundspeaker outputs to the respectivespeakers.

To assure that all the audio signals are carried toyour speakers without loss of clarity orresolution, we suggest that you use high-qualityspeaker cable. Many brands of cable areavailable and the choice of cable may beinfluenced by the distance between yourspeakers and the receiver, the type of speakersyou use, personal preferences and other factors.Your dealer or installer is a valuable resource toconsult in selecting the proper cable.

Regardless of the brand of cable selected, we recommend that you use a cable constructed offine, multistrand copper with an area greaterthan 2 mm2.

Cable with an area of 1.5 mm2 may be used forshort runs of less than 4 m. We do not recom-mend that you use cables with an area less than1mm2 due to the power loss and degradation inperformance that will occur.

Cables that are run inside walls should have theappropriate markings to indicate listing with anyappropriate testing agency standards. Questionsabout running cables inside walls should bereferred to your installer or a licensed electricianwho is familiar with the applicable local buildingcodes in your area.

When connecting wires to the speakers, be certain to observe proper polarity. Note that thepositive (+) terminal of each speaker connectionnow carries a specific color code as noted onpage 8. However, most speakers will still use ared terminal for the postive (+) connection.Connect the negative or black wire to thesame terminal on both the receiver and thespeaker.

NOTE: While most speaker manufacturersadhere to an industry convention of using blackterminals for negative and red ones for positive,some manufacturers may vary from thisconfiguration. To assure proper phase andoptimal performance, consult the identificationplate on your speaker or the speakers manual toverify polarity. If you do not know the polarity ofyour speaker, ask your dealer for advice beforeproceeding, or consult the speakersmanufacturer.

We also recommend that the length of cableused to connect speaker pairs be identical. Forexample, use the same length piece of cable toconnect the front-left and front-right or surround-left and surround-right speakers,even if the speakers are a different distancefrom the AVR.

9. Connections to a subwoofer are normallymade via a line level audio connection from theSubwoofer Output to the line-level inputof a subwoofer with a built-in amplifier. When apassive subwoofer is used, the connection firstgoes to a power amplifier, which will be con-nected to one or more subwoofer speakers. Ifyou are using a powered subwoofer that doesnot have line-level input connections, follow theinstructions furnished with the speaker for con-nection information.

10. If an external multi-channel audio sourcewith 5.1 outputs such as an external digitalprocessor/decoder, DVD-Audio, SACD, Blu-ray orHD-DVD player is used, connect the outputs ofthat device to the 8-Channel Direct Inputs.

Video Equipment Connections

Video equipment is connected in the same man-ner as audio components. Again, the use of high-quality interconnect cables is recommended topreserve signal quality. To ensure best video per-formance S-Video sources should be connectedto the AVR only with their S-Video In/Outputs,not with their composite video connectors too.

If you have already connected a source device toone of the HDMI inputs as explained in theAudio Equipment section, then you have auto-matically made a video connection at the sametime, as the HDMI signal includes both digitalaudio and video components.

If your video display or source device is notHDMI-capable, you will need to use one of theanalog video connections (composite, S- or com-ponent video), if available, as described below.

If the source device is not capable of transmit-ting its digital audio signal through the HDMIconnection, then use one of the coaxial or opti-cal digital audio inputs for the source.

If a multichannel analog audio connection isrequired for certain lossless formats (e.g. DVD-Audio, SACD, HD-DVD or Blu-ray Disc), you maymake both connections. To listen to the multi-channel disc, first select the HDMI source input,then select the 6-/8-channel analog audioinputs, and the AVR will retain the last videosource you selected.

Installation and Connections

INSTALLATION AND CONNECTIONS 19

ENG

LISH

Installation and Connections

1. Connect a VCRs audio and video Play/Outjacks to the Video 2 In jacks on the rearpanel. The Audio and Video Record/In jacks onthe VCR should be connected to the Video 1Out jacks on the AVR.

2. Although any video device may be connectedto these jacks, we recommend connecting yourTV to the Audio 1 Audio/Video Input Jacks so that you may take advantage of thefact that the remote control is preprogrammedwith TV product codes for the Video 1 device.For the same reason, we recommend connectingyour video recorder, cable TV converter orsatellite receiver to the Video 2 Audio/VideoInput Jacks.

3. Connect the analog audio and video outputsof a DVD or laser disc player to the DVD jacks .

4. Connect the digital audio outputs of a CD,MD or DVD player, satellite receiver, cable box orHDTV converter to the appropriate Optical orCoaxial Digital Inputs *.Remember that the DVD source defaults to theCoaxial 1 Digital Input. All other sourcesdefault to their analog inputs, although anysource may be assigned to any digital audioinput on the receiver.

NOTE: When connecting a device such as a digi-tal cable box or other set-top tuner product witha digital audio output, we recommend that youconnect both the digital and analog outputs ofthe product to your AVR. The audio input pollingfeature of the AVR will then be able to make cer-tain that you have a constant audio feed, since itwill automatically switch the audio input to theanalog jacks if the digital feed is interrupted ornot available for a particular channel.

5. Connect the Composite and S-Video (if S-Video device is in use) Monitor Outputjacks on the receiver to the composite and S-Video input of your television monitor or videoprojector.

6. If your DVD player and monitor both havecomponent video connections, connect the com-ponent outputs of the DVD player to the Video1 Component Video Inputs. Note thateven when component video connections areused the audio connections must still be madeto either the analog DVD Audio Inputs orany of the Coaxial or Optical Digital Inputjacks .

7. If another component video device is avail-able, connect it to the Video 2 or Video 3Component Video Input jacks * . Theaudio connections for this device should bemade to either the Video 2 Input jacks # orany of the Coaxial or Optical Digital Inputjacks .

8. If the component video inputs are used,connect the Component Video Output tothe component video inputs of your TV, projectoror display device.

9. If you have a camcorder, video game or otheraudio/video device that is connected to the AVRon a temporary, rather than permanent basis,connect the audio, video and digital audio out-puts of that device to the Front Panel Inputs*. A device connected to the Video 4jacks is selected as the Video 4 input, andconnected to the digital jacks * it is selected as "Optical 3" or "Coaxial 3" input.(See page 24 for more information on inputconfiguration.)

10. When connecting the AVR 347 to a stan-dard, analog video display that has standardcomposite and S-Video inputs only, componentvideo inputs may not be used. In this case, con-nect the Video and S-Video Monitor Outputs to the matching composite and S-Videoinputs on your video display, depending onwhich types of video are used by your sourcedevices. If both types of video are used by differ-ent source devices, than both Video MonitorOutputs must be separately connected toyour television.

Video Connection Notes: All component inputs/outputs can be used for

RGB signals too, in the same way as describedfor the Y/Pr/Pb signals, then connected to thejacks with the corresponding color.But this is only correct as long as only thethree RGB video signals are output by thevideo source, with a sync signal in the "G"signal only, without any sync signal outputseparately by the source.

SCART A/V ConnectionsFor the connections described above your videodevice needs RCA (cinch) connectors or/and S-Video connectors for all Audio and Video signals:Any normal video device (Not SVHS or High 8)for only playback needs 3 RCA jacks, VCRs forrecord and playback even 6 RCA jacks. Any S-Video device (SVHS, High 8) needs 2 RCA(Audio) and 1 S-Video jack (Video), if its a play-back unit, or 4 RCA (Audio In/Out) and 2 S-Video (Video In/Out) jacks, if its a recordingVCR.

Many european video devices are equipped withRCA (Cinch) or S-Video jacks only partially, notfor all audio and video in/outputs needed asdescribed above, but with a so called Scart orEuro-AV connector (almost rectangular jack with21 pins, see drawings on next page).

In that case the following Scart to Cinchadapters or cables are needed:

Units for playback, such as satellite receivers,camcorders, DVD or LD players, need anadapter from Scart to 3 RCA plugs, see fig. 1(normal video devices) or from Scart to 2RCA+1 S-Video plugs, see fig. 4 (S-Videodevices).

HiFi VCRs need an adapter from Scart to 6RCA plugs, see fig. 2 (normal video), or fromScart to 4 Audio+2S-Video jacks, see fig. 5 (S-Video VCR). Read carefully the instructionattached to the adapter to find which of thesix plugs is used for the record signal to theVCR (connect with the AVRs Out jacks) andfor the playback signal from the VCR (connectwith the AVRs In jacks). Do not misconnectAudio and Video signals. Dont hesitate to con-sult your dealer, if you are uncertain.

If you use only normal video devices the TVmonitor needs an adapter from 3 RCA plugsto Scart (fig. 3) only. If also S-Video devices areused an adapter from 2 RCA+1S-Video plugsto Scart is needed additionally (fig. 6), con-nected to the SCART input on your TV that isprovided for S-Video.

20 INSTALLATION AND CONNECTIONS

Installation and Connections

Note that only the video plugs (the "yellow"cinch plug in fig. 3 and the S-Video plug in fig. 6) must be connected to the TV MonitorOutput, and the volume on the TV must bereduced to minimum.

Important Note for Adapter Cables:If the cinch connectors of the adapter youll useare labeled, connect the Audio and Video Inplugs with the corresponding Audio and VideoIn jacks on the AVR (and with a VCR connectthe Out plugs to the Out jacks on the VCR).Note that with some adapter types it may bejust turned around: If no signal is audible/ visiblewhen the VCR is playing connect the Outplugs to the In jacks on the AVR and turnedaround. If the adapter plugs are not labeled inthat way, pay attention to the signal flowdirections as shown in the diagrams above andin the instruction attached to the adapter. Ifuncertain, dont hesitate to consult your dealer.

Important Notes for S-Video connections:1. Only the S-Video In/Out of S-Video devicesmust be connected to the AVR, NOT both,normal video and S-Video In/Outputs (except theTV, see item below).When both connections are made, only the S-Video signal will be viewed on the screen.

Figure 1:SCART/Cinch-Adapter

for playback;signal flow:

SCART Cinch

Figure 2:SCART/Cinch-Adapter

for record and playback;signal flow:

SCART Cinch

Figure 3:Cinch/SCART-Adapter for

playback;signal flow:

Cinch SCART

Figure 4:SCART/S-Video Adapter

for playback;signal flow:

SCART Cinch

Figure 5:SCART/S-Video Adapter

for record and playback;signal flow:

SCART Cinch

Figure 6:SCART/S-Video Adapter

for playback;signal flow:

Cinch SCART

Black

Yellow

Red

Black

Red

Blue1

Yellow

Green1

White

Black

Yellow

Red

Red

Black

S-Video In

Red

Black

S-Video Out

Black

Red

Blue1

Yellow

S-Video In

S-Video Out

1 Also other colours possible, e.g. brown and grey.

Important Note for the Use of SCART-Cinch Adapters:When video sources are connected to the TVdirectly with a SCART cable, specific controlsignals apart from Audio/Video signals will befed to the TV. These specific signals are: With allvideo sources, the signal for automatic inputselection that switches the TV automatically tothe appropriate input as soon as the videosource is started. And with DVD players, thesignals automatically turning the TV to 4:3/16:9format (with 16:9 TVs or with 4:3 TVs withselectable 16:9 format) and turning the RGBvideo decoder of the TV on or off, depending onthe DVD players setting. With any adapter cable,these control signals will be lost and theappropriate setting of the TV must be mademanually.

Note for RGB signal with SCART:If you use a unit providing RGB signals on aSCART output (as e.g. most DVD players do) andyou want to use that RGB signal, this SCARToutput must be connected directly to your TV.Although the AVR can switch three-way videosignals (like component signals Y/Pb/Pr), mostTVs need separate sync signals for RGB (alsowith SCART) that cannot be switched andprovided by the AVR.RGB signals can be pathed through the AVR onlywhen no separate sync signal is needed (see lastVideo Connection Note on page 15).

INSTALLATION AND CONNECTIONS 21

ENG

LISH

Installation and Connections

System and Power ConnectionsThe AVR 347 is designed for flexible use withmultiroom systems, external control componentsand power amplifiers.

Main Room Remote Control ExtensionIf the receiver is placed behind a solid or smokedglass cabinet door, the obstruction may preventthe remote sensor from receiving commands. Inthis event, the remote sensor of any Harman Kardon or other compatible device, notcovered by the door, or an optional remotesensor may be used. Connect the Remote IROutput of that device or the output of theremote sensor to the Remote IR Input jack !.

If other components are also prevented fromreceiving remote commands, only one sensor isneeded. Simply use this units sensor or a remoteeye by running a connection from the RemoteIR Output jack to the Remote IR Inputjack on Harman Kardon or other compatibleequipment.

Multiroom IR LinkThe key to remote room operation is to link theremote room to the AVRs location with wire foran infrared receiver and speakers or an amplifier.The remote room IR receiver (this can be anoptional IR receiver or any other remotableHarman Kardon device in the remote room withIR sensor integrated) should be connected to theAVR via standard coaxial cable. Connect theRemote IR Output of the device or of theoptional sensor with the Multiroom IR Inputjack ) on the AVRs rear panel.

If other Harman Kardon compatible sourceequipment is part of the main room installation,the Remote IR Output jack on the rearpanel should be connected to the IR IN jack onthat source device. This will enable the remoteroom location to control source equipmentfunctions.

When a remote IR sensor is used to control non-Harman Kardon source equipment, we recom-mend that you make a direct connection or usean optional, external IR blaster connected tothe Remote IR Carrier Output Jack+. If youare in doubt as to which IR Output jack to usefor the equipment in your system, contact yourdealer or installer, or the manufacturers supportsite and ask whether the unit to be controlleduses full carrier or stripped carrier IRcommands. When full carrier commands areused, make the connection to the Remote IRCarrier Output Jack+. Otherwise, make theconnection to the Remote IR Output Jack as noted above.

NOTE: All remotely controlled components mustbe linked together in a daisy chain. Connectthe IR OUT jack of one unit to the IR IN of thenext to establish this chain.

Multiroom Audio ConnectionsDepending on your system`s requirement anddistance from the AVR to the remote room, threeoptions are available for audio connection:

Option 1: Use high-quality, shielded audiointerconnect phono cable from the AVRs loca-tion to the remote room. In the remote room,connect the interconnect cable to a stereopower amplifier. The amplifier will be connectedto the rooms speakers. At the AVR, plug theaudio interconnect cables into the MultiroomOutput Jacks ' on the AVRs rear panel.

Option 2: Place the amplifier that will providepower to the remote location speakers in thesame room as the AVR, and connect theMultiroom Output jacks ' on the rear panelof the AVR to the audio input of the remoteroom amplifier. Use the appropriate speaker wireto connect the optional power amplifier to theremote speakers. High-quality wire of at least 2.5 mm2 is recommended for long multiroomconnections.

Option 3: Taking advantage of the AVRs built-in seven-channel amplifier, it is possible