panel au optronics m150xn07 v1 0 [ds]

Global LCD Panel Exchange Center www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

(C) Copyright AU Optronics, Inc.

Feb. 2003 All Rights Reserved. M150XN07 Ver0.1 1/28

No Reproduction and Redistribution Allowed.

AU OPTRONICS CORPORATION

Product Specifications

15.0 XGA Color TFT-LCD Module

Model Name: M150XN07V.1

Approved by Prepared by

DDBU Marketing Division / AU Optronics Croporation

Customer Checked & Approved by

Spec. No.: DDPM-M150XN07-0.1

Version: 1

Total pages: 26

Date: 2003-July-31






Product Specifications

15.0 XGA Color TFT-LCD ModuleModel Name:M150XN07

V.1

() Preliminary Specifications( ) Final Specifications






i Contents

1.0 Handling Precautions

2.0 General Description2.1 Display Characteristics2.2 Functional Block Diagram

3.0 Absolute Maximum Ratings

4.0 Optical Characteristics4.1 Signal for Lamp connector4.2 Parameter guideline for CCFL Inverter

5.0 Signal Interface5.1 Module Interface Connectors 5.2 Module Connector Pin Configuration5.3 Backlight Connectors5.4 Backlight Connector Pin Configuration5.5 Signal Electrical Characteristics5.6 Interface Timings Characteristics5.7 Interface Timing Definition

6.0 Pixel format image

7.0 Power Consumption

8.0 Power ON/OFF Sequence

9.0 Backlight Characteristics9.1 Signal for Lamp connector9.2 Parameter guideline for CCFL Inverter

10.0Vibration, Shock, and Drop10.1 Vibration & Shock

10.1.1 Vibration Test Spec 10.1.2 Shock Test Spec

10.2 Drop

11.0 Environment11.1 Temperature and Humidity

11.1.1 Operating Conditions11.1.2 Shipping Conditions

11.2 Atmospheric Pressure11.3 Thermal Shock

12.0 Reliability12.1 Failure criteria 12.2 Failure rate

12.2.1 Usage 12.2.2 Components de-rating

12.3 CCFL life12.4 ON/OFF cycle






13.0 Safety13.1 Sharp edge requirement 13.2 Material

13.2.1 Toxicity13.2.2 Flammability

13.3 Capacitors13.4 Hazardous voltage

14.0 Other requirements14.1 Smoke free design14.2 National test lab requirement

15.0 Label

16.0 Mechanical Characteristics

ii Record of Revision

Version and Date Page Old description New Description Remark0.1 2003/06/10 All First Edition for Customer All






1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector.3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when

handling.7) Do not open nor modify the Module Assembly.8) Do not press the reflector sheet at the back of the module to any directions.9) In case if a Module has to be put back into the packing container slot after once it was taken out from the

container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFLReflector edge softly. Otherwise the TFT Module may be damaged.

10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the InterfaceConnector of the TFT Module.

11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist norbend the TFT Module even momentary. At designing the enclosure, it should be taken into considerationthat no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Modulemay be damaged.

12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal.

13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (2.11, IEC60950 or UL1950), or be applied exemption.

14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit (2.4, IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.






2.0 General DescriptionThis specification applies to the 15.0 inch Color TFT-LCD Module M150XN07.The display supports the XGA (1024(H) x 768(V)) screen format and 262,144 colors (RGB 6-bits data).All input signals are 1 Channel LVDS interface compatible.This module does not contain an inverter card for backlight.

Features-XGA 1024(H) x 768(V) resolution

-2 CCFLs (Cold cathode Fluorescent Lamp)

-High contrast ratio, high aperture ratio

-Wide viewing angle

-High-speed response

-Low power consumption

ApplicationDesktop monitors

2.1 Display CharacteristicsThe following items are characteristics summary on the table under 25 condition:ITEMS Unit SPECIFICATIONSScreen diagonal [mm] 381 (15)Outline dimension [mm] 326.5 x 253.5 x 12.0 typ.Display Area [mm] 304.128 (H) x 228.096(38.1cm diagonal) Resolution 1024(R,G,B x 3) x 768 Pixel Pitch [mm] 0.297 x 0.297 Pixel Arrangement R.G.B. Vertical StripeDisplay Mode TN mode, Normally WhiteTypical white Luminance. [cd/m2] 250nit (typ) @8mA (note 1)Brightness uniformity 80% typ. (note 2)Luminance uniformity 1.7 max.(Note 3) Crosstalk (at 60Hz) 1.2% max. (note 4) Contrast Ratio 400 : 1 typ.Support Colors 262,144 colors (6-bit for R,G,B)Chromaticity(CIE1931)

White-x 0.313White-y 0.329

Color Gamut 60% typ., of NTSC coverageViewing angle 60(left),60(right),40(up),60(down) CR=10Response Time [msec] 16ms typ. (Tr +Tf)Nominal Input Voltage VDD [Volt] +3.3 V Power Consumption

(VDD line + CCFL line)[Watt] 15 (typ.) @8mA (All Black Pattern)

Electrical Interface LVDS (1 ch)Frame rate [Hz] 60Hz typ., 75Hz max.Weight [Grams] 1100 typ.Mounting method Side mountingSurface treatment Anti-glare, hard coating (3H) Temperature Range

OperatingStorage (Shipping)

[oC][oC]

0 to +50 -20 to +60






Note 1: Brightness is measured at the center point of brightness value with all pixels displaying white.

Note 2: Brightness uniformity of these 9 points is defined as below:

(Min. brightness / Max. brightness) x 100%

Note 3: TCO 99 Certification Requirements and test methods for environmental labeling of Display Report No. 2

defines Luminance uniformity as below:

((Lmax,+30deg. / Lmin,+30deg.) + (Lmax,-30deg. / Lmin,-30deg.)) / 2

256 512

192

384

576

Unit: pixels

1

3

5

2

4

768

50 %

90 %

90 % 50 %

10 %

Unit: percentage of dimension of display area

10 %






TCO 99 certification requirements and test methods:

1) Diagrammatic

Effective areaWH

2) D is the diagonal of the screen in centimeters. And md is as follow.

md(cm)=D1.5 with a minimum distancemd=50 cm

3) The measurement positions shall consist of an active white square of size 4 by 4 cm.

4) Measure Lmax+30and Lmin+30that are given as points L & R. And then rotated to an azimuth angle of 30

degrees and measure Lmax-30and Lmin-30again using the same procedure.

5) The variation in luminance ratio is calculated as the ratio: LR =(( Lmax+30/ Lmin+30)(Lmax-30/ Lmin-30))/2 1.7

Note 4:

Unit: percentage of dimension of display area

l LA-LA l / LA x 100%= 1.2% max., LA and LB are brightness at location A and B

l LB-LB l / LB x 100%= 1.2% max., LA and LB are brightness at location A and B

1/2

1/2

1/6

1/6A

B

1/2

1/2

1/6

1/6

2/3 1/3

1/3

2/3

A

B

184 gray level 184 gray level

0 gray level

md

Lmax+30and Lmin+30






2.2 Functional Block DiagramThe following diagram shows the functional block of 15.0 inches Color TFT-LCD Module:

DF-14H-20P-1.25H (Hirose) JST BHR-03VS-1CWY20G-A0D1T (PTWO)

Connector

DC/DC

Converter

LVDS

Timing

Gamma

Correction

TFT-LCD1024*(3)*768

Pixels

G1

G768

D1 D3072

InverterDC POWER

2 CCFL

AU ASIC

RSDS+ 3.3 V

LVDS






3.0 Absolute Maximum RatingsAbsolute maximum ratings of the module is as following:

Item Symbol Min Max Unit ConditionsLogic/LCD Drive Voltage VDD 0.3 +3.6 [Volt]

Input Voltage of Signal Vin 0.3 VDD+0.3 [Volt]CCFL Current ICFL 3.0 8.5 [mA] rms Note 1 Operating Temperature TOP 0 +50 [oC] Note 2 Operating Humidity HOP 20 85 [%RH] Note 2 Storage Temperature TST -20 +60 [oC] Note 2 Storage Humidity HST 5 95 [%RH] Note 2 Vibration 1.5 / 10-200 [G / Hz]Shock 50/20 [G / ms] Half sine waveAssured Torque at Side Mount 2.0 [kgf.cm]Re-screw 3 [Times]

Note 1: CCFL life time will drop dramatically if exceeding 8.0 mA; It will have safety concern if exceeding 8.5 mA.

Note 2: Maximum Wet-Bulb should be 39 and No condensation.

Wet bulb temperature chart

Relative Humidity %

Temperature oC-20 0 6050

95

5

100

0

Operation rangeStorage range

Storage range

90

80

70

60

50

40

30

20

10

Twb=39T=40,H=95%

T=60,H=39%

T=65,H=29%

T=50,H=55%






4.0 Optical CharacteristicsThe optical characteristics are measured under stable conditions at 25 (Room Temperature):

Item Unit Conditions Min. Typ. Max.

Viewing Angle[degree]

[degree]

Horizontal (Right)

CR = 10 (Left)

Horizontal (Right)

CR =5 (Left)

50

50

60

60

60

60

75

75

CR: Contrast Ratio[degree]

[degree]

Vertical (Upper)

CR = 10 (Lower)

Vertical (Upper)

CR = 5 (Lower)

30

50

60

65

40

60

70

75Contrast ratio Normal Direction 300 400 -

Response Time( Note 1) [msec] Raising Time Ton( 10%-90% ) - 4 6

[msec] Falling Time Toff ( 90%-10% ) - 12 17

[msec] Raising + Falling - 16 23Color / Chromaticity Red x 0.587 0.617 0.647Coordinates (CIE) Red y 0.317 0.347 0.377

Green x 0.260 0.290 0.320Green y 0.563 0.593 0.623Blue x 0.118 0.148 0.178Blue y 0.070 0.100 0.130

Color Coordinates (CIE) White White x 0.283 0.313 0.343White y 0.299 0.329 0.359

Brightness Uniformity [%] 75 80 -

White Luminance at CCFL 8.0mA

White Luminance at CCFL 6.5mA[cd/m2] 200

170

250

200

-

-Crosstalk ( in 60Hz)

[%] 1.2

Note 1: Definition of Response time:The output signals of photodetector are measured when the input signals are changed from Black to White

(falling time), and from White to Black (rising time), respectively. The response time interval between the 10% and 90% of amplitudes. Refer to figure as below.

TrR TrD

10090

100

%

OpticalResponse

white

black

white






5.0 Signal Interface 5.1 Module Interface Connectors

Physical interface is described as for the connector on module.

These connectors are capable of accommodating the following signals and will be following components

Connector Name Interface Connector

Manufacturer Hirose, PTWO or compatible

Type / Part Number DF-14H-20P-1.25H (Hirose)CWY20G-A0D1T (PTWO)

5.2 Module Connector Pin Configuration

DF-14H-20P-1.25H (Hirose) or CWY20G-A0D1T (PTWO)

Pin No. Symbol Description

1 VDD Power Supply, 3.3V (typical)

2 VDD Power Supply, 3.3V (typical)

3 VSS Ground

4 VSS Ground

5 Rin0- - LVDS differential data input (R0-R5, G0)

6 Rin0+ + LVDS differential data input (R0-R5, G0)

7 VSS Ground

8 Rin1- - LVDS differential data input (G1-G5, B0-B1)

9 Rin1+ + LVDS differential data input (G1-G5, B0-B1)

10 VSS Ground

11 Rin2- - LVDS differential data input (B2-B5, HS, VS, DE)

12 Rin2+ + LVDS differential data input (B2-B5, HS, VS, DE)

13 VSS Ground

14 ClkIN- - LVDS differential clock input

15 ClkIN+ + LVDS differential clock input

16 VSS Ground

17 Rin3- NC

18 Rin3+ NC

19 VSS Ground

20 NC Please *floating* and dont connect to ground.






5.3 Backlight Connectors

Connector Name / Designation For Lamp Connector

Manufacturer JST or compatible

Type / Part Number BHR-03VS-1

Mating Type / Part Number SM02(8.0)B-BHS-1-TB

5.4 Backlight Connector Pin Configuration

Pin Symbol Description

1 HV Lamp High Voltage

2 NC No connection

3 LV Ground

Cable length: 140 +- 5 mm

Connector-output position: right side (front view)

Lamp assy design shall be easy for replacement and repair.

5.5 Signal Electrical Characteristics

Each signal characteristics are as follows;

Item Symbol Min Typ Max UnitLCD Drivevoltage

VDD +3.0 +3.3 +3.6 [V]

High input signalvoltage

Vih 2.0 - - [V]

Low input signalvoltage

Vil - - 0.8 [V]






6bits input data format

Note: R/G/B data 7:MSB, R/G/B data 0:LSB

Vdiff=0V

DE VS HS B5 B4 B3 B2

B1 B0 G5 G4 G3 G2 G1

G0 R5 R4 R3 R2 R1 R0

Previous Data for current Clk cycle Next

Clkln

R0IN0

R1IN1

R2IN2






5.6 Signal Electrical Characteristics

Input signals shall be low or Hi-Z state when Vin is offIt is recommended to refer to the specifications of SN75LVDS82DGG (Texas Instruments) in detail.

Each signal characteristics are as follows:

Parameter Condition Min Max Unit

VthDifferential InputHighVoltage(Vcm=+1.2V) 100 [mV]

Vtl Differential Input LowVoltage(Vcm=+1.2V) -100 [mV]

5.7 Interface TimingsBasically, interface timings described here is not actual input timing of LCD module but output timing ofSN75LVDS82DGG (Texas Instruments) or equivalent.

5.7.1 Timing Characteristics

Signal Parameter Symbol MIN TYP MAX UnitClock Timing Clock frequency clk 50 65 81 MHz

Horizontal active Thd 1024 1024 1024 TclkHorizontal blanking Thbl 40 320 400 Tclk

Hsync Timing

Horizontal period Th 1064 1344 1424 TckVertical active Tvd 768 768 768 ThVertical blanking Tvbl 8 38 75 Th

Vsync Timing

Vertical period Tv 776 806 843 Th

Note: Typical value refer to VESA STANDARD






5.8 Interface Timing Definition






6.0 Pixel format image Following figure shows the relationship of the input signals and LCD pixel format.






7.0 Power ConsumptionInput power specifications are as follows;

Symbol Parameter Min Typ Max Units ConditionVDD LCD Drive Voltage 3.0 3.3 3.6 [V]

IDD LCD Drive Current TBD TBD TBD [mA] VDD=3.3v, All Black Pattern

PDD LCD Drive powerconsumption

TBD TBD TBD [Watt] VDD=3.3v, All Black Pattern

VDDns AllowableLCD Drive Ripple Noise

100 [mV]p-p

8.0 Power ON/OFF SequenceVDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart.

10%

10%10%

10%10%

90% 90%

0 min.0 min.

1secmin.

10ms max.

Vin

LampOn

Signal

0 V

0 V

0 V

200ms






9.0 Backlight Characteristics9.1 Signal for Lamp connector

Pin # signal Name

1 Lamp High Voltage

2 No connection

3 Ground

9.2 Parameter guide line for CCFL Inverter

Symble Parameter Min Typ Max Units Condition

IRCFL CCFL operation range 2.5 8.0 8.5 [mA]rms

(Ta=25)Note 4

ICFL CCFL Inrush current - - 20 [mA]

FCFL CCFL Frequency 40 55 80 [KHz] (Ta=25)Note 1

ViCFL(25)(reference)

CCFL Ignition Voltage1000

[Volt]rms

(Ta= 25)Note 3

ViCFL(0)(reference)

CCFL Ignition Voltage1300

[Volt]rms

(Ta= 0)Note 3

VCFL CCFL Discharge Voltage (Reference) 590 650

[Volt]rms

(Ta=25)Note 2

PCFL CCFL Power consumption@ 8mA (excludinginverter)

9.4 10.4 [Watt] (Ta=25)Note 2

Note 1: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD Note 2: Calculator value for reference (IRCFLVCFLx2=PCFL)Note 3: CCFL inverter should be able to give out a power that has a generating capacity of over 1300 voltage.

Lamp units need 1300 voltage minimum for ignition Note 4: CCFL life time 30,000hr at 8mA,its defined as when the brightness is reduced by half.

Its recommended not to exceed 8.0 mA for CCFL life time concern and its prohibited to exceed 8.5 mA forsafety concern.






10.0 Vibration,Shock,and Drop10.1 Vibration & ShockThe module shall work error free after following vibration and shock condition. Likewise the module shall not sustain

any damage after vibration and shock test.

10.1.1 Vibration Test Spec: Frequency:10 - 200Hz

Sweep: 30 Minutes each Axis (X, Y, Z)

Acceleration: 1.5G(10~200Hz P- P)

Test method:

Acceleration (G) 1.5

Frequency (Hz) 10~200~10

Active time (min) 30

10.1.2 Shock Test Spec:

Acceleration (G) 50

Active time(ms) 20

Wave form Half-sin

Times 1

Direction: X , Y, Z

10.2 DropPackage test: The drop height is defined as 60 cm.

(1 corner,3 edges,6 flat faces)-- No damage and defect found for panel.






11.0 EnvironmentThe display module will meet the provision of this specification during operating condition or after storage or

shipment condition specified below. Operation at 10% beyond the specified range will not cause physical

damage to the unit.

11.1 Temperature and Humidity

11.1.1 Operating ConditionsThe display module operates error free, when operated under the following conditions; Temperature 0 0C to 50 0CRelative Humidity 20% to 85%Wet Bulb Temperature 39.0 0C

11.1.2 Shipping Conditions The display module operates error free, after the following conditions; Temperature -20 0C to 60 0CRelative Humidity 5% to 95% Wet Bulb Temperature 39.0 0C

11.2 Atmospheric PressureThe display assembly is capable of being operated without affecting its operations over the pressure range as following specified:

Pressure Altitude

Maximum Pressure 1040 hPa 0 m = sea level

Minimum Pressure 601 hPa 3658 m = 12,000 feet

Note: Non-operation altitude limit of this display module = 40,000 feet. = 12193 m.

11.3 Thermal ShockThe display module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature change consists of varying the temperature from -200C to 600C, and back again.

Thermal shock cycle -20 0C for 30min 60 0C for 30min

Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours before powering on.






12.0 ReliabilityThis display module and the packaging of that will comply following standards.

12.1 Failure Criteria The display assembly will be considered as failing unit when it no longer meets any of the requirements statedin this specification. Only as for maximum white luminance, following criteria is applicable.

Note: Maximum white Luminance shall be 75 cd/m2 or more.

12.2 Failure Rate The average failure rate of the display module (from first power-on cycle till 1,000 hours later) will notexceed1.0%. The average failure rate of the display module from 1,000 hours until 10,000 hours will notexceed 0.70% per 1000 hours.

12.2.1 UsageThe assumed usage for the above criteria is: 220 power-on hours per month 500 power on/off cycles per month Maximum brightness setting Operation to be within office environment (250C typical)

12.2.2 Component De-ratingAll the components used in this device will be checked the load condition to meet the failure rate criteria.

12.3 CCFL LifeThe assumed CCFL Life will be longer than 30,000 hours under stable condition at 255 0C;Standard current at 8.0 0.5 mADefinition of life: brightness becomes 50% or less than the minimum luminance value of CCFL.

12.4 ON/OFF CycleThe display module will be capable of being operated over the following ON/OFF Cycles.

ON/OFF Value Cycle

+VDD and CCFL power 36,000 10 seconds on / 10 seconds off

13.0 Safety13.1 Sharp Edge RequirementsThere will be no sharp edges or corners on the display assembly that could cause injury.

13.2 Materials13.2.1 ToxicityThere will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they

will be reviewed and approved by the responsible AUO Toxicologist.

13.2.2 FlammabilityAll components including electrical components that do not meet the flammability grade UL94-V1 in the module

will complete the flammability rating exception approval process. The printed circuit board will be made from

material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.






14.0 Other requirements 14.1 Smoke Free DesignAny smoke nor strange smell shall not be observed by the operator at any single failure.

14.2 National Test Lab RequirementThe display module will satisfy all requirements for compliance to the following requirement:

UL 1950, First Edition U.S.A. Information Technology EquipmentCSA C22.2 No.950-M89 Canada, Information Technology Equipment IEC 950 International, Information Technology Equipment EN 60 950 International, Information Processing Equipment

(European Norm for IEC950)

The construction of the display module is designed to suppress EMI. When mounted into a specified host system, the system will meet the following EMI requirement:

FCC Part 15 Class B VCCI Class 2 CISPR 22, class B Taiwan CNS standard China CCIB standard

15.0 Label



(C) C

opyr

ight

AU

Opt

roni

cs, I

nc.

Feb.

2003

All

Rig

hts

Res

erve

d.M

150X

N07

Ver

0.1

24/2

8

No

Rep

rodu

ctio

n an

d R

edis

tribu

tion

Allo

wed

.

16.0

Mec

hani

cal C

hara

cter

istic

s



(C) C

opyr

ight

AU

Opt

roni

cs, I

nc.

Feb.

2003

All

Rig

hts

Res

erve

d.M

150X

N07

Ver

0.1

25/2

8

No

Rep

rodu

ctio

n an

d R

edis

tribu

tion

Allo

wed

.



(C) C

opyr

ight

AU

Opt

roni

cs, I

nc.

Feb.

2003

All

Rig

hts

Res

erve

d.M

150X

N07

Ver

0.1

26/2

8

No

Rep

rodu

ctio

n an

d R

edis

tribu

tion

Allo

wed

.

panel au optronics m150xn07 v1 0 [ds]

Documents

lcd pdp oled panel application

copyright au optronics

m150xn07 ver0

step solution

xga color tftlcd modulemodel

redistribution allo

signal interface5

vibration test spec