parts list - honda mcshop.hondamc.se/k7mp3/media/productfiles/08l71mjj...1 of 11 87940-mjj-d300...
TRANSCRIPT
Issue Date
February 2013
INSTALLATIONINSTRUCTIONS
Accessory Application Publication No.
MII
© 2013 Honda Motor Co., Ltd. - All Rights Reserved.
PARTS LIST
87940-MJJ-D3001 of 11
PANNIER SUPPORT STAY P/N 08L71-MJJ-D30
NC700X/XA/XDNC700S/SA/SD
NC700D
No. Description Qty
(1( Right pannier hook 1
(2( Left pannier hook 1
(3( Right pannier hook cover 1
(4( Left pannier hook cover 1
((( 6 mm collar (thick( 4
(6( 6 mm collar (thin/large( 4
(7( Pannier bracket 2
(8( 6 mm collar (thin/small( 2
(9( 6 mm collar (middle( 2
(10( 6 mm socket bolt 4
(11( 6 mm flange nut 4
(12( Washer (small( 8
(13( Right pannier support stay 1
(14( Left pannier support stay 1
(1(( Stopper rubber 2
(16( 8 mm socket bolt (short( 2
(17( 8 mm socket bolt (middle( 2
(18( 8 mm socket bolt (long( 4
(19( 8 mm collar (long( 4
(20( 8 mm collar (short( 2
(21( Washer (large( 16
(22( URL paper 1
(19(
(21(
(18(
(16(
(17(
(10(
(8((12(
(9(
(1(
(3(
(4(
(2(
((( (6(
(14(
(13(
(7(
(1((
(22(
(20(
(12((11(
PANNIER STAY(Sold separately)
(1(
(2(
(3(
No. Description Qty
(1( Right pannier stay 1
(2( Left pannier stay 1
(3( Plug 4
2 of 11
INSTALLATION INFORMATION CAUTION
To prevent burns, allow the engine, exhaust system, • radiator, etc. to cool before installing the accessory.
NOTE:The Pannier stay which is sold separately is required • to install this accessory.The Pannier stay is not required for the motorcycle • equipped with the Pannier stay.Take care not to damage the painted surfaces of the • motorcycle.When the motorcycle is already equipped with the • Rear carrier, remove the Rear carrier and Pannier stay before installing this accessory.
Item N·m kgf·m Ibf·ft
6 mm socket bolt 10 1.0 7
6 mm flange nut 12 1.2 9
8 mm socket bolt 24 2.4 18
TORQUE CHARTTighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.
TOOLS AND SUPPLIES REQUIREDBox-end wrench (10 mm(Hex wrench (4 and ( mm(Electric drill: NC700X/XA/XD/S/SA/SDHole saw (20 mm(: NC700X/XA/XD/S/SA/SDFileFretsawScissorsScaleWoodblock (10 mm in thickness(: NC700X/XA/XD/S/SA/SDElectrical tape: NC700X/XA/XD/S/SA/SDIsopropyl alcoholShop towelTorque wrench
(2(
(6(((((3((4(
(1(
No. Description Qty
(1( Right pannier 1
(2( Left pannier 1
(3( Right emblem 1
(4( Left emblem 1
((( Plate 2
(6( Washer 2
1KEY PANNIER(Sold separately)
3 of 11
CONTENTSRefer to the following page according to each model.INSTALLATION <NC700X/XA/XD/S/SA/SD> .............P.3INSTALLATION <NC700D> .........................................P.6
INSTALLATION <NC700X/XA/XD/S/SA/SD>Illustration shows NC700XA type, other types • are similar.
1. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
BOLT
NUT
FLANGE COLLAR
SINGLE SEAT
PILLION SEAT
SPRING
WASHERCLIP
PILLION SEAT HINGE 3. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
RIGHT REAR GRIP
LEFT REAR GRIP (Save(
CAP (Save(
WASHER
FLANGE COLLAR
SOCKET BOLT
SOCKET BOLT
BOLT
DRIVE CHAIN CASE
2. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
4 of 11
RIGHT REAR GRIP (Save(
PILLION SEAT HINGE
WASHER
WASHERCLIP
(. Remove the pillion seat hinge as shown.
4. Work upon the rear fender B as shown.Be careful not to damage harnesses.• Remove any burrs from the edge of the hole.• Repeat on the left side.•
7. Install the right pannier hook as shown.Repeat on the left side.•
RIGHT PANNIER STAY
WASHER (small(
6 mm COLLAR (thin/large(
6 mm COLLAR (thick(
6 mm FLANGE NUT
RIGHT PANNIER HOOK
RIGHT PANNIER HOOK COVER
RIGHT PANNIER STAY
PILLION SEAT HINGE (Reuse(
WASHER (Reuse(
CLIP (Reuse(
8. Install the pillion seat hinge as shown.
BOLT (Save(
NUT (Save(
RIGHT PANNIER STAY
6. Remove the bolts and nuts as shown.Repeat on the left side.•
REAR FENDER B
SLIT Remove.FILE
File off the cutout surface.
5 of 11
9. Loosely install the pannier stays as shown.
RIGHT PANNIER SUPPORT STAY
RIGHT PANNIER SUPPORT STAY
10. Loosely install the right pannier support stay as shown.
Repeat on the left side.•
8 mm SOCKET BOLT (long(
8 mm SOCKET BOLT (middle(
8 mm SOCKET BOLT (short(
WASHER (large(
WASHER (large(
RIGHT PILLION STEP HOLDER
WASHER (large(
8 mm COLLAR
(long(
8 mm COLLAR (short(
8 mm COLLAR (short(
RIGHT PANNIER STAY
LEFT PANNIER STAY
FLANGE COLLAR (Reuse( WASHER
(Reuse(
SOCKET BOLT (Reuse(
SOCKET BOLT (Reuse(
6 mm SOCKET BOLT
PANNIER BRACKET
RIGHT PANNIER
WASHER (small(
6 mm COLLAR (middle(
6 mm COLLAR (thin/small(
12. Install the pannier bracket as shown.Repeat on the left side.•
<Right side>
11. Install the stopper rubber as shown.Make two sets.•
PANNIER BRACKET
PANNIER BRACKET
48 mm
STOPPER RUBBER
STOPPER RUBBER
6 of 11
When securing the pannier support stay, first tighten the upper bolts.
UPPER BOLT
13. Install the right pannier and tighten all loosely installed hardware to the specifications in the torque chart.
Repeat on the left side.•
14. Install the plugs as shown.
1(. Install the removed parts in the reverse order of removal.
RIGHT PANNIER
INSTALLATION <NC700D>1. Open the seat, remove the rear seat as shown.
REAR SEATBOLT
FLANGE COLLAR
2. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
CAP (Save(
PLUG
WASHER
FLANGE COLLAR
RIGHT REAR GRIP (Save(
LEFT REAR GRIP (Save(
SOCKET BOLT
SOCKET BOLTTORQUE: 30 N·m (3.1 kgf·m, 22 lbf·ft)
7 of 11
4. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
Repeat on the right side.•
3. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
LEFT SIDE COVER
REAR COWL
REAR COWL
SEAT LOCK CABLE
BOLT
BOLT
CLIP
CLIP
CLIP
CLIP
COVEROpen.
SCREW
CONNECTORSDisconnect.
RUBBERRemove.
(. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
6. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
BOLT
BOLT
PILLION SEAT STAY
REAR FENDER A
8 of 11
7. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
REAR FENDER B
CONNECTORRelease.
BOLT
BOLT
DRIVE CHAIN CASE
8. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
RIGHT PANNIER SUPPORT STAY
RIGHT PANNIER SUPPORT STAY
9. Loosely install the right pannier support stay as shown.
Repeat on the left side.•
8 mm COLLAR (short(
8 mm COLLAR (short(
8 mm SOCKET BOLT (long(
8 mm SOCKET BOLT (middle(
8 mm SOCKET BOLT (short(
WASHER (large(
WASHER (large(
WASHER (large(
8 mm COLLAR (long(
10. Remove the bolts and nuts as shown.Repeat on the left side.•
BOLT (Save(
NUT (Save(
RIGHT PANNIER STAY
<Right side>
RIGHT PILLION STEP HOLDER
9 of 11
11. Install the right pannier hook as shown.Repeat on the left side.•
RIGHT PANNIER STAY
LEFT PANNIER STAY
FLANGE COLLAR (Reuse(
12. Loosely install the pannier stays as shown.
WASHER (Reuse(
SOCKET BOLT (Reuse(
SOCKET BOLT (Reuse(
RIGHT PANNIER STAY
WASHER (small(
6 mm COLLAR (thin/large(
6 mm COLLAR (thick(
6 mm FLANGE NUT
RIGHT PANNIER HOOK
RIGHT PANNIER HOOK COVER
13. Install the stopper rubber as shown.Make two sets.•
14. Install the pannier bracket as shown.Repeat on the left side.•
6 mm SOCKET BOLT
PANNIER BRACKET
RIGHT PANNIER
WASHER (small(
6 mm COLLAR (middle(
6 mm COLLAR (thin/small(
PANNIER BRACKET
PANNIER BRACKET
48 mm
STOPPER RUBBER
STOPPER RUBBER
10 of 11
When securing the pannier support stay, first tighten the upper bolts.
1(. Install the right pannier and tighten all loosely installed hardware to the specifications in the torque chart.
Repeat on the left side.•
RIGHT PANNIER
UPPER BOLT
16. Temporarily remove the panniers and pannier stays.
REAR FENDER B
14 mm
14 mm
14 mm
5.5 mm
18. Install the rear fender B and A in the reverse order of removal.
17. Work upon the rear fender B as shown .Remove any burrs.•
FILEFile off the cutout surfaces after removing the area.Repeat on the right side.
FRETSAW Remove.
FRETSAW Remove.
SOCKET BOLT TORQUE: 30 N·m (3.1 kgf·m, 22 lbf·ft)
11 of 11
20. Install the side covers and rear cowl in the reverse order of removal.
RIGHT SIDE COVER
FACTORY MARKED LINE
RIGHT SIDE COVER
19. Work upon the right side cover along the factory marked line as shown.
Remove any burrs.• Repeat on the left side.•
FILEFile off the cutout surfaces after removing the area.
FRETSAW Remove.
21. Loosely install the right pannier stay and right pannier, then tighten all loosely installed hardware to the specifications in the torque chart.
Repeat on the left side.•
22. Install the plugs as shown.
23. Install the removed parts in the reverse order of removal.
RIGHT PANNIER
RIGHT PANNIER STAY
PLUG
SOCKET BOLT (Reuse(TORQUE: 30 N·m (3.1 kgf·m, 22 lbf·ft)
SOCKET BOLT (Reuse(TORQUE: 30 N·m (3.1 kgf·m, 22 lbf·ft)