peerless pump company vertical turbine … lit/peerless turbines/section... · peerless pump...
TRANSCRIPT
Subject to change without notice
Peerless Pump Company Indianapolis, IN 46207-7026
VERTICAL TURBINE PUMPS Right Angle Gears
SECTION 110 Page 1 January 2, 2007
Shaft Guarding for Horizontal Mounted Spicer Universal Joint Drive Shafts
A shaft guard must be supplied with all Spicer shafts (see Spicer price list for pricing) and all quotations and orders must include or specify shaft guard when drive shafts are quoted or ordered.
They are relatively easy to install and a 2 inch wide opening runs the full length of the bottom of the guard to facilitate shaft lubrication.
IMPORTANT: These guards do not comply with California Code or OSHA requirements. If shaft guard is specified to meet OSHA requirements by customer we cannot accept order. Please refer to Section 10 page 8 for instructions concerning orders with OSHA compliance specifications.
We strongly recommend that guarding requirements and design be resolved with customer before entering order and that design be in compliance with any local or state codes. The standard guard furnished (as shown below) only provides minimal protection for most commercial and industrial applications where equipment is installed in limited access buildings or enclosures.
VERTICAL TURBINE PUMPS
50 Hz Motor Rpm
1470 1760 2112 2347 2640 3080 List Wt.Part No. Part Part Price Lbs.
Shaft No. No. 5:6 1:1 6:5 4:3 3:2 7:4
Only Flanges 1 Guard
SC1310 268646808 269523301 to 269523306 268646901 40 47 53 57 62 70 $1,392 30
SC1350 268646809 269253601 to 269253612 268646901 60 80 91 98 106 119 $1,495 35
SC1410 268646801 269253601 to 269253612 268646901 75 97 110 118 128 143 $1,499 40
SC1480 268646802 269253701 to 269253719 268646902 100 130 147 159 172 192 $2,214 50
SC1550 268646803 269253701 to 269253719 268646902 125 165 188 202 219 245 $2,301 55
SC1610 268646811 269253801 to 269253819 268646902 200 259 295 317 345 - $3,241 68
SC1710 268646812 269253901 to 269253926 268646902 250 347 391 426 - - $4,337 79
SC1810 268646813 269254001 to 269254026 268646902 350 448 510 549 - - $4,700 114
SC1880 268646814 269254101 to 269254126 268646902 450 590 670 722 - - $11,876 131
SC1910 268646810 No Part Nos. 268646902 750 996 1126 1225 - - $13,877 180
Peerless Pump
Shaft Size
Maximum Bhp @ 1760 Rpm Output speed 2
1 Note: Customer must supply mating shaft diameters, keyway dimension, driver Bhp & Rpm for all non Peerless Pump supplied equipment.
Peerless Pump
Peerless Pump
2 Standards for shaft sizings are: B-10 life of 5000 hours; working installation angle of 3 degrees; Diesel engines without any
Right Angle Gear Ratio
Engine Rpm
50 Hz & Diesel Engine Driven Units
and 50 Hz 4 Pole Horizontal Motors Speed Increasing Right Angle Gear for 1760 RPM output
All Power Transmission Short Coupled Universal Joint Drive Shafts for Direct
List price includes shaft, dynamic balancing, fastener kits, large ( through 61)and standard companion (71 & Up) flanges with set screw over keyway and set screw @ 90 deg from keyway
and shaft guard.
Connected Vertical Turbine Fire Pumps with Right Angle Gears. 2 or 4 Stroke Diesel Engines,
Peerless Pump CompanyIndianapolis, IN 46207-7026
SECTION 110Page 2February 2, 2007
Subject to change without notice
Pump Drive Price List,
Sept. 15, 2014
Ratio 30 40 60A 80A 100A 125A 150A 200A 250 300 350 450A 500A 600A 750A 1000G
1:1 1,970 2,560 2,580 2,890 3,090 3,300 4,040 4,890 7,830 8,480 9,980 13,810 14,310 17,430 27,930 36,190
10:11 NA NA 3,120 3,250 3,430 3,700 4,120 4,890 9,350 9,810 11,300 CF 16,810 CF 30,840 40,850
5:6 NA 3,180 3,040 3,370 3,490 3,510 4,510 5,510 9,380 10,080 12,200 16,490 17,700 19,630 29,390 47,100
3:4 NA NA 3,430 3,660 3,840 4,310 CF CF CF CF CF CF CF CF CF CF
2:3 2,180 2,980 3,290 3,390 3,600 4,310 CF 5,860 9,630 10,380 11,880 CF CF CF 30,840 47,890
4:7 NA 3,180 2,810 3,100 3,310 3,640 CF CF CF CF CF CF CF CF CF CF
1:2 2,180 2,740 2,810 3,100 3,310 3,430 CF NA 9,380 10,080 12,280 CF CF CF CF CF
11:10 NA NA 2,580 2,890 3,090 3,310 4,040 5,550 9,380 10,080 12,280 16,450 17,700 20,540 30,840 41,250
6:5 NA CF 2,580 2,890 3,090 3,310 4,040 5,150 7,830 8,480 9,980 16,110 16,860 19,390 27,930 38,990
5:4 NA NA 2,580 2,890 3,090 3,310 CF CF 9,110 9,810 11,520 CF CF CF CF CF
4:3 NA CF 2,580 2,890 3,090 3,310 4,040 5,150 7,830 8,480 9,980 16,090 16,130 19,390 27,930 CF
3:2 2,690 CF 2,950 3,270 3,490 3,700 4,210 5,860 8,880 9,570 11,240 15,810 17,700 20,800 29,390 41,250
7:4 NA CF CF CF CF NA CF CF NA NA CF CF CF CF CF CF
2:1 NA CF CF CF CF CF CF CF CF CF CF CF CF CF CF CF
5:2 NA NA CF CF CF NA CF CF CF CF CF CF CF CF CF CF
3:1 NA NA CF CF CF NA NA CF CF CF CF CF CF CF CF CF
SH C CA1SS
30 CF 4,790 8,420 3,070 752 NA 1,500 70 70
40 CF 4,790 8,420 3,350 783 111 1,820 70 110
60A CF 6,850 8,420 3,500 989 172 1,190 70 170
80A CF 6,850 8,420 3,500 989 172 1,190 70 170
100A 920 6,850 9,800 3,500 1,410 INCL 1,190 70 170
125A 940 7,630 10,390 3,730 1,410 INCL 1,190 70 170
150A 1,100 8,410 11,340 4,430 1,410 INCL 1,390 70 170
200A 1,100 8,410 15,900 4,430 1,730 INCL 1,600 70 210
250 2,160 10,170 CF 4,860 CF INCL 1,600 70 250
300 2,160 10,170 CF 4,860 1,730 INCL 1,600 70 250
350 2,160 10,170 CF 4,860 1,730 INCL 1,600 70 250
450A 2,560 CF CF 6,740 2,500 INCL 2,170 100 330
500A 2,560 CF CF 6,740 2,500 INCL 2,170 100 330
600A 2,820 CF CF 6,740 2,500 INCL 2,170 100 330
750A 2,820 CF CF 8,450 2,940 INCL 2,290 180 390
1000G 2,950 CF CF 9,770 3,910 INCL 2,360 210 610 1Prices are for 1760 rpm pump speed. Contact factory for pump speeds other than 1760 rpm.
2Export boxes are made from heat treated lumber.
Model
NET PricesLIST Prices
Amarillo Gear Company manufactures right angle gear drives for applications up to 3,000 horsepower. Contact factory for prices and availability of gear drives
not described in the catalog.
Type Marine
Package
Water
Cooler
Spec.
Rotation
Paint
Color
Export
Box2
* Model 40 is available with either a 12" BD (40A) or 16½" BD (40B)
I. Hollow shaft, types: (non‐reverse included)SL: Opposed Thrust RatingS: Standard Heavy Thrust RatingSH: Extra Heavy Thrust RatingC: Manual CombinationCA: Automatic Combination
II. Solid Shaft, types: (non‐reverse included)SS: Heavy Thrust Rating
III. Marine Package includes stainless steel hardware, stainless steel oil tube and epoxy paint. External Marine Heat Exchanger is included on model 100A and larger.
IV. Check following applications with engineering as price additions may be required:1. Steam turbine or other high speed driver. 2. Pump speeds slower than indicated in catalog.3. Pump speed greater than 1800 rpm.
©2014
2401 Sundown Lane • Amarillo, TX • 79118
www.amarillogear.com
(806) 622 ‐ 1273 • fax (806) 622 ‐ 3258
[email protected] PSPD 9/14
DE'RAN GEAR, INC. PRICE LIST9405 N. County Road 2000 September 1, 2013Lubbock, Texas 79415Phone 806-746-6926, Fax 806-746-6518
STANDARD GEAR DRIVES, FIGURE 1 ROTATIONRATIO 1:2 4:7 2:3 3:4 4:5 5:6 10:11 1:1 11:10 6:5 5:4 4:3 3:2 7:4 2:1
2160 N/A 2160 1920 N/A 1920 N/A 1920 N/A 1920 N/A 1920 2160 N/A 2160J30 2220 N/A 2220 2030 N/A 2030 N/A 2030 N/A 2030 N/A 2030 2270 N/A 2270J40 2320 2320 2320 2210 2210 2210 2210 2210 2210 2210 2210 2210 2320 2320 2320J60 2570 2570 2380 2460 2460 2460 2460 2460 2460 2460 2460 2460 2570 2570 2570J80 2890 2890 2890 2780 2780 2780 2780 2780 2780 2780 2780 2780 2890 2890 2890
G40A 2970 2970 2970 2970 2970 2970 2800 2800 2970 2970 2970 2970 3200 3200 3200G60A 3100 3100 3400 3400 3400 3100 3100 3100 3100 3100 3100 3100 3350 3350 3350G80A 3400 3400 3630 3630 3630 3170 3170 3170 3170 3170 3170 3170 3630 3630 3630G100A 3620 3620 4010 4010 4010 3740 3740 3390 3390 3390 3390 3390 3920 4320 4320G125A 3850 3850 4250 4250 4250 3850 3850 3630 3630 3630 3630 3630 4150 4150 4150J150 5220 5220 5220 4690 4690 4890 4680 4440 4430 4430 4430 4430 4690 N/A N/A
G150A 5440 5440 5110 5110 5110 4790 4790 4790 4790 4790 5110 5110 5110 5440 5440G200B 6080 6080 6080 5650 5650 5650 5380 5380 5650 5650 5650 5650 6080 6800 6800G250A 9450 9880 9880 9530 9530 9450 9450 8570 9450 8570 9450 8750 9450 9880 9880G300A 10230 10590 10590 10360 10360 10230 10230 9270 10230 10230 10230 9770 9770 10590 10590G350A N/A 11130 11130 11020 11020 10920 10920 10920 10920 10920 10920 10920 11130 C/F C/FG400A N/A N/A 13170 13170 13170 12960 12960 12960 12960 12960 12960 12960 13170 N/A N/AG450A N/A N/A 14210 14210 14210 14000 14000 14000 14000 14000 14000 14000 14210 N/A N/AF500A 19100 19100 18300 17260 17260 17260 15660 15660 17260 17260 15660 15660 18300 19100 19100F590A 22650 22650 22650 20940 20940 20940 19090 19090 20940 20940 20940 20940 22650 22650 23550F750A 37690 37690 31180 34450 34450 28920 32970 30600 32970 31180 31180 31180 32970 39870 39870F1000A 48450 48450 48450 43680 43680 43680 43680 39650 43680 42720 43680 43680 45190 45190 45190F1200A C/F C/F C/F C/F C/F 45960 45960 45960 45960 45960 C/F C/F C/F C/F C/FF1500A C/F C/F C/F C/F C/F 52010 52010 52010 52010 52010 C/F C/F C/F C/F C/F
OPTIONS - TO BE ADDED TO THE LIST PRICE OF STANDARD DRIVES
MODEL
Combination Motor Stand
Manual Automatic
J20 1090 400 2540 N/A 720 N/A 3440 6350 N/A N/A 90J30 1090 N/A 2540 N/A 720 N/A 3440 6350 N/A N/A 90J40 1270 830 2720 N/A 810 190 N/A N/A N/A N/A 130J60 1270 830 2720 N/A 810 190 N/A N/A N/A N/A 130J80 1270 830 2720 N/A 810 190 N/A N/A N/A N/A 130
G40A 1640 1010 2900 1810 910 180 4080 6430 480 360 160G60A 1640 1010 2900 1810 910 180 4080 6430 480 360 160G80A 1640 1010 2900 1810 910 180 4080 6430 480 360 160
G100A 1640 1200 2900 1810 1070 180 4080 6430 480 360 160G125A 1640 1200 2900 1810 1070 180 4720 6620 480 360 160J150 1810 1200 2900 2000 1390 INCL 4990 6800 480 N/A 160
G150A 1990 1630 3080 2000 1450 180 5440 7980 605 360 190G200B 2180 1970 3080 2000 1450 180 5620 8700 605 360 190G250A 2180 1970 3620 2000 1910 INCL 7620 10160 INCL 360 190G300A 2180 N/A 3620 N/A 1910 INCL 7620 11240 INCL 360 240G350A 2180 N/A 3620 N/A 1910 INCL 7620 11240 INCL 360 240G400A 2240 N/A 3620 N/A 1910 INCL 8350 11610 INCL 360 240G450A 2240 N/A 3620 N/A 1910 INCL 8350 11610 INCL 360 240F500A 3090 3260 5260 N/A 2420 INCL 8700 17770 INCL 360 300F590A 3090 N/A 5260 N/A 2420 INCL 8700 22680 INCL 360 300F750A 3090 N/A 5440 N/A 2650 INCL 13520 22680 INCL 360 370
F1000A 3270 4350 5810 N/A 3630 INCL 23400 29940 C/F 360 480F1200A 3270 4350 5810 N/A 3860 INCL 23400 29940 C/F 360 540
LEGEND: C/F = CONTACT FACTORY N/A = NOT AVAILABLE INCL = INCLUDED
VISIT OUR WEBSITE @ WWW.DERANGEAR.COM
MODEL J20
Special Rotation Fig.2,3,4
Extra Heavy Thrust
Vertical Solid Shaft
Opposed Thrust
Bearings
Marine Package
Copper Water Cooler
Sprag Non Reverse
Factory Mutual FM
Label
Net Export Box
DE'RAN GEAR, INC. PRICE LIST9405 N. County Road 2000 September 1, 2013Lubbock, Texas 79415Phone 806-746-6926, Fax 806-746-6518
PROPELLER PUMP GEAR DRIVESRATIO 2:1 5:2 3:1 7:2 4:1 9:2 5:1 11:2 6:1
4290 4940 4940 N/A N/A N/A N/A N/A N/AM200P 6500 7520 7520 N/A N/A N/A N/A N/A N/AM16AH 10140 10140 10140 10290 10290 N/A 10580 N/A N/AM20A 16620 16620 16620 17700 17700 17700 17700 17700 17700M22A 30100 30100 30100 30100 30100 30100 30100 30100 30100M26A 43640 43640 43640 43640 43640 43640 43640 43640 43640M30A 53530 53530 53530 53530 53530 53530 53530 53530 53530M32A CONTACT FACTORYM34A CONTACT FACTORYM36A CONTACT FACTORYM40A CONTACT FACTORYM44A CONTACT FACTORYM48A CONTACT FACTORYM52A CONTACT FACTORY
OPTIONS - TO BE ADDED TO THE LIST PRICE OF STANDARD DRIVES
MODEL
Combination Motor Stand
Manual Automatic
M80P 1620 1010 2890 C/F 970 180 4940 C/F 130 INCL 1990M200P 2170 1970 3070 C/F 1440 180 5600 C/F 160 INCL 2890M16AH 1270 C/F 3070 INCL 1200 C/F 7220 C/F 160 INCL 3240M20A 2170 C/F 3240 INCL 1440 C/F 7590 C/F 170 INCL 3600M22A 2520 C/F 3430 INCL 1690 C/F 8130 C/F 200 INCL 3980M26A 3980 C/F 3790 INCL 1920 C/F 8490 C/F 230 INCL 4330M30A 5050 C/F 5230 INCL 2170 C/F 10470 C/F 370 INCL 6860M32A CONTACT FACTORYM34A CONTACT FACTORYM36A CONTACT FACTORYM40A CONTACT FACTORYM44A CONTACT FACTORYM48A CONTACT FACTORYM52A CONTACT FACTORY
C/F = Contact Factory N/A = Not Available INCL = Included
MODEL M80P
Special Rotation Fig.2,3,4
Extra Heavy Thrust
Vertical Solid Shaft
Opposed Thrust
BearingsMarine
PackageCopper Water Cooler
Net Export Box
Sprag Non-Reverse
Slant Drives
Propeller Pump Drives are fan cooled and require no additional water cooling. Marine Package includes stainless steel hardware, nameplate, oil tube, and epoxy paint. If sea water cooler, or shell and tube external cooler is required, please contact factory. All prices are subject to change without notice. . VISIT OUR WEBSITE @ WWW.DERANGEAR.COM