phone vtech 6042_manual.i2
TRANSCRIPT
-
8/2/2019 Phone vtech 6042_manual.i2
1/62
.vtechphnes.cm
Ths manual has all the feature operatons and troubleshootng necessary to nstalland operate your new VTech telephone. Please revew ths manual thoroughly to
ensure proper nstallaton and operaton of ths nnovatve and feature rch VTech
product. For support, shoppng, and everythng new at VTech, vst our webste at
www.vtechphones.com. In Canada, please vst www.vtechcanada.com.
Cntultins
on purchasng your new VTech product.Before usng ths telephone, please read the
Imptnt sfet instuctins
on page 39 of ths manual.
-
8/2/2019 Phone vtech 6042_manual.i2
2/62
.vtechphnes.cm
Installaton . . . . . . . . . . . . . . . . . . . . . . . . 1
Parts checklst . . . . . . . . . . . . . . . . . . . . . . 1
Install handset battery . . . . . . . . . . . . . . . . . . 2
Telephone base nstallaton . . . . . . . . . . . . . . . 3Desk/table bracket nstallaton . . . . . . . . . . . . . . 4
Dal type . . . . . . . . . . . . . . . . . . . . . . . . . 4
DSL lter . . . . . . . . . . . . . . . . . . . . . . . . . 5
Telephone settngs . . . . . . . . . . . . . . . . . . . . 6
Handset layout . . . . . . . . . . . . . . . . . . . . . . 6
Telephone base layout . . . . . . . . . . . . . . . . . . 7
Date and tme. . . . . . . . . . . . . . . . . . . . . . . 8
Rng melody . . . . . . . . . . . . . . . . . . . . . . . 8
Rng volume . . . . . . . . . . . . . . . . . . . . . . . 9Battery low tone . . . . . . . . . . . . . . . . . . . . . 9
Out of range tone . . . . . . . . . . . . . . . . . . . . 10
Key tone . . . . . . . . . . . . . . . . . . . . . . . . 10
Edt handset name . . . . . . . . . . . . . . . . . . . 11
Language . . . . . . . . . . . . . . . . . . . . . . . . 11
Dal type . . . . . . . . . . . . . . . . . . . . . . . . 12
Clear vocemal . . . . . . . . . . . . . . . . . . . . . 12
Reset to default settngs . . . . . . . . . . . . . . . . 13
Temporary tone dalng . . . . . . . . . . . . . . . . . 13Basc operaton . . . . . . . . . . . . . . . . . . . . . 14
Make, answer and end calls . . . . . . . . . . . . . . 14
Optons whle on calls . . . . . . . . . . . . . . . . . 14
Speakerphone . . . . . . . . . . . . . . . . . . . . . 14
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Call watng . . . . . . . . . . . . . . . . . . . . . . . 14
Intercom call . . . . . . . . . . . . . . . . . . . . . . 15
Multple handset use . . . . . . . . . . . . . . . . . . 15Answer an external call durng an ntercom call . . . . 15
Transfer an external call . . . . . . . . . . . . . . . . 16
Fnd handset . . . . . . . . . . . . . . . . . . . . . . 16
Advanced operaton . . . . . . . . . . . . . . . . . . 17
Drectory . . . . . . . . . . . . . . . . . . . . . . . . 17
Revew the drectory . . . . . . . . . . . . . . . . . . 17
Search the drectory . . . . . . . . . . . . . . . . . . 17
Chart of characters . . . . . . . . . . . . . . . . . . . 18
Store an entry n the drectory . . . . . . . . . . . . . 19Dal a drectory entry . . . . . . . . . . . . . . . . . . 19
Edt an entry n the drectory . . . . . . . . . . . . . . 20
Delete from the drectory . . . . . . . . . . . . . . . 20
About caller ID nformaton . . . . . . . . . . . . . . . 21
Call log . . . . . . . . . . . . . . . . . . . . . . . . . 22
Revew the call log . . . . . . . . . . . . . . . . . . . 22
Dal a call log number . . . . . . . . . . . . . . . . . 23
Store a number from the call log . . . . . . . . . . . . 23
Delete from the call log . . . . . . . . . . . . . . . . . 24Redal . . . . . . . . . . . . . . . . . . . . . . . . . 25
Revew redal . . . . . . . . . . . . . . . . . . . . . . 25
Store a number from redal to the drectory . . . . . . 25
Dal a number from redal . . . . . . . . . . . . . . . 26
Tble f cntents
-
8/2/2019 Phone vtech 6042_manual.i2
3/62
.vtechphnes.cm
Tble f cntentsDelete from redal. . . . . . . . . . . . . . . . . . . . 26
Answerng system operaton . . . . . . . . . . . . . . 27
Message capacty . . . . . . . . . . . . . . . . . . . 27
Actvate the answerng system . . . . . . . . . . . . . 28Set number of rngs. . . . . . . . . . . . . . . . . . . 28
Set telephone base date and tme . . . . . . . . . . . 28
Set telephone base melody . . . . . . . . . . . . . . 29
Set telephone base rnger volume . . . . . . . . . . . 29
Change personal identication number (PIN) . . . . . 30
Outgong announcements . . . . . . . . . . . . . . . 31
Play the announcement . . . . . . . . . . . . . . . . 31
Record your own announcement . . . . . . . . . . . 31
Delete your announcement. . . . . . . . . . . . . . . 32Message playback . . . . . . . . . . . . . . . . . . . 32
Optons durng playback . . . . . . . . . . . . . . . . 32
Delete all messages . . . . . . . . . . . . . . . . . . 32
Remote access . . . . . . . . . . . . . . . . . . . . . 33
Message wndow dsplays . . . . . . . . . . . . . . . 34
Handset and telephone base ndcators . . . . . . . . 35
Handset lght . . . . . . . . . . . . . . . . . . . . . . 35
Telephone base lghts . . . . . . . . . . . . . . . . . 35
Handset cons . . . . . . . . . . . . . . . . . . . . . 35Handset dsplay screen messages. . . . . . . . . . . 36
Call log dsplay messages . . . . . . . . . . . . . . . 37
Battery . . . . . . . . . . . . . . . . . . . . . . . . . 38
Important safety nstructons . . . . . . . . . . . . . . 39
Troubleshootng . . . . . . . . . . . . . . . . . . . . 40
Operatng range . . . . . . . . . . . . . . . . . . . . 50
Mantenance . . . . . . . . . . . . . . . . . . . . . . 50
About cordless telephones . . . . . . . . . . . . . . . 51Warranty . . . . . . . . . . . . . . . . . . . . . . . . 51
FCC, ACTA and IC regulatons . . . . . . . . . . . . . 53
The RBRC Seal . . . . . . . . . . . . . . . . . . . . 54
Technical specications . . . . . . . . . . . . . . . . 5 5
Index . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6
-
8/2/2019 Phone vtech 6042_manual.i2
4/62
.vtechphnes.cm 1
Instlltion
Bsic
opertion
Instlltin
Pts checklistRemember to save your sales recept and orgnal packagng n case t s necessary to shp your
telephone for warranty servce. Check to make sure the telephone package ncludes the followng: To purchase
replacementbatteres, or obtana replacementpower adapter,vst our webste atwww.vtechphones.com or call1 (800) 595-9511.In Canada, go towww.vtechcanada.
com or call1 (800) 267-7377.
For 6043 and6053, the batterycompartmentcovers areattached to thehandsets.
4. Users manual
1. Quck start gude 2. Handsets 3. Telephone base
5. Chargers
7. Base power adapter
6. Charger adapters
10. Telephone lne cord8. Batteres
1. Quck start gude
2. Handsets (2 for 6042/6043,
3 for 6052/6053)
3. Telephone base
4. Users manual
5. Chargers (1 for 6042/6043,
2 for 6052/6053)
6. Charger adapters (1 for 6042/6043,
2 for 6052/6053)
7. Base power adapter
8. Batteres(2 for 6042/6043,
3 for 6052/6053)
9. Battery compartment covers
(2 for 6042/6043,3 for 6052/6053)
10. Telephone lne cord
9. Battery compartment covers
-
8/2/2019 Phone vtech 6042_manual.i2
5/62
.vtechphnes.cm2
Install handset battery Remove battery compartment cover by pressing on the indentation and sliding it downwards (only
for 6043 and 6053).
Align the two holes in the plug with the socket pins according to the color-coded label in thebattery compartment, then snap the plug nto place.
Place the battery nto the compartment.
Poston the battery compartment cover and slde t upwards untl t clcks nto place.
Put the handset n the telephone base or the charger to charge the new battery for at least 16
hours. The battery may have enough charge for short calls. For best performance, charge t for
at least 16 hours.
You can keep the battery charged by returnng the handset to the telephone base or charger after
each use. When the battery power s fully depleted, a full rech arge takes about 16 hours.For further nformaton on batteres, please see theBattery secton on page 38.
If the handset wll
not be used for along perod of tme,remove the batteryto prevent possbleleakage.
To purchasereplacementbatteres, vst ourwebste at www.vtechphones.com or call1 (800) 595-9511.In Canada, go towww.vtechcanada.com or call1 (800) 267-7377.
Instlltin
color-coded label
-
8/2/2019 Phone vtech 6042_manual.i2
6/62
.vtechphnes.cm 3
Instlltion
Bsic
opertion
Instlltin
Install the telephone base and the charger as shown below. Choose a locaton away from any electroncequpment and applances such as personal computers, computer routers, televson sets, mcrowave
ovens, and refrgerators. Avod excessve heat, cold, dust or mosture.
Use only theVTech batteresand poweradapters (orequivalent)suppled wthths telephone.To obtan areplacement, vstour webste atwww.vtechphones.com or call
1 (800) 595-9511.In Canada, go towww.vtechcanada.com or call1 (800) 267-7377.
Ths power unts ntended to becorrectly orentedin a vertical or oormount poston.
The prongs are notdesgned to holdthe plug n place ft s plugged nto aceiling, under-the-table or cabnetoutlet.
2. Plug the power adapter nto an electrcaloutlet not controlled by a wall swtch.
1. Plug the telephone lne cordnto a telephone wall jack.
Telephne bse instlltin
-
8/2/2019 Phone vtech 6042_manual.i2
7/62
.vtechphnes.cm4
Instlltin
Desk/tble bcket instlltinThe telephone base comes wth the desk/table bracket nstalled and ready for tabletop use.
Dil tpeIf you have touch-tone service, your telephone is ready to use as soon as the battery is charged. If
you have pulse (rotary) service, the dial type must be changed. To change the dial type, see
Dil tpe on page 12.
To remove the bracket:
1. Push the bracket away from the telephone
base as shown below. Do not remove the
bracket by force to avod breakage of
the tabs.
To nstall the bracket:
1. Algn the tabs of the bracket wth the slots
at the bottom of the telephone base as
shown n the dagram.
2. Slde the bracket towards the center
of the telephone base untl t clcks
nto place.
-
8/2/2019 Phone vtech 6042_manual.i2
8/62
.vtechphnes.cm 5
Instlltion
Bsic
opertion
DSL lter (for
DSL users)
To single telephone jack (RJ11C) Telephone lne cord
If u subscibe t DSL seviceIf you receive high speed internet through your telephone line (commonly referred to as DSL), and
you are experencng nterference durng telephone conversatons and/or your caller ID features are
not functioning properly, install a DSL lter to the telephone line between the telephone base andthe telephone wall jack. Contact your DSL provider for a DSL lter.
Instlltin
-
8/2/2019 Phone vtech 6042_manual.i2
9/62
.vtechphnes.cm6
Telephne settins
Hndset lut1. Earpece
2. / (directory/volume)
3. (speakerphone)
4. /FLASH
5. Dialing keys (0-9,*,#)
6. REDIAL/PAUSE
7. Mcrophone
8. Handset dsplay
9. MENU/SELECT
10. CID / (caller ID/volume)
11. OFF/CLEAR
12. MUTE/REMOVE
13. INT (intercom)
1
2
4
5
3
7
8
10
9
11
1213
6
-
8/2/2019 Phone vtech 6042_manual.i2
10/62
.vtechphnes.cm 7
Bsic
opertion
Telephon
esettings
Telephne settins
Telephne bse lut
1. CHARGE lght
2. IN USE light3. /REPEAT
4. Message wndow
5. FIND HANDSET
6. Speaker
7. VOICEMAIL lght
8. X/DELETE
9. VOLUME+/-
10. /SKIP11. ANS ON/OFF
(answer on/off)
12. Mcrophone
13. NO. OF RINGS
14. ANNC (announcement)
15. /PLAY/STOP
9
4
3
7
14
12
6
8
5
12 13
1011
15
-
8/2/2019 Phone vtech 6042_manual.i2
11/62
.vtechphnes.cm8
Telephne settins
Dte nd time Press MENU/SELECT to dsplay menu when n dle mode.
Press or to reach DaTE/TIME. Press MENU/SELECT.
Use the keypad to set the year. Press MENU/SELECT. Use the keypad to set the date. Press MENU/SELECT.
Use the keypad to set the tme. Press or to select a.m. or p.m.
Press MENU/SELECT.
The screen dsplays STorEDand youll hear a conrmation beep.
rin meldThere are ten rng melodes for the handset to choose from.
Press MENU/SELECT to dsplay menu when n dle mode.
Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach rINg MELoDy. Press MENU/SELECT, and
a checkmark s shown next to the current rng melody.
Press or to scroll through the choces and a sample of each
rng melody wll be played.
Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
Stored
YeAr 200\
dAte \1/01
tIMe \2:12AM
MelodY 1MelodY 2
rING MelodYrING voluMe
When enterng
the date or tme, fthe dgt s sngle,a zero must beentered rst (i.e.f the tme s 6:08,you must enter0608).
If you havemore than onehandset, settngthe date and tmeon one handsetwll apply to allother handsets.
The rng melodyfor the telephonebase s setseparately fromthe handset rngmelody. Seepage 29 to set the
telephone basemelody.
-
8/2/2019 Phone vtech 6042_manual.i2
12/62
.vtechphnes.cm 9
Bsicopertion
Telephon
esettings
The handset wllnot rng when the
rnger volume s atthe lowest settng.A rnger off conwll be dsplayed.
Whle thetelephone srngng, youcan temporarlyslence the rngerby pressng
oFF/CLEar orMUTE/rEMoVE.The next call wllrng normally. Arnger off conwll be dsplayed.
Btte l tneThe handset s preset to beep when the battery level s low.
Press MENU/SELECT to dsplay the menu when n dle mode.
Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach ToNES. Press MENU/SELECT.
Press or to reach BaTTEry Low. Press MENU/SELECT.
A checkmark s shown next to the current selecton. Press orto choose oN or oFF.
Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
BAtterY low
out of rANGe
oN
off
rin vlumeThe handset ringer volume can be adjusted, there are ve levels to
choose from.
Press MENU/SELECT to dsplay menu when n dle mode. Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach rINg VoLUME. Press MENU/SELECT.
Press or to scroll through the choces and a sample of each rng
volume wll be played.
Press MENU/SELECT to conrm selection. The screen displays
STorED and youll hear a conrmation beep.
You can adjust the rnger volume by pressng VoL+/VoL- on the
telephone base when the telephone s rngng.
toNeS
HANdSet NAMe
Telephne settins
The volume ofthe telephonebase rnger s setseparately from
the handset rnger.See page 29 fortelephone basernger volumesettngs.
-
8/2/2019 Phone vtech 6042_manual.i2
13/62
.vtechphnes.cm10
out f ne tneThe handset wll beep durng a conversaton when t s out of range from
the telephone base. Ths tone s preset to oN.
Press MENU/SELECT to dsplay the menu when n dle mode. Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach ToNES. Press MENU/SELECT.
Press or to reach oUT oF raNgE. Press MENU/SELECT.
A checkmark s shown next to the current selecton. Press or
to choose oN or oFF.
Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
Ke tneThe handset s preset to beep whenever any button s pressed.
Press MENU/SELECT to dsplay the menu when n dle mode.
Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach ToNES. Press MENU/SELECT.
Press or to reach KEy BEEPS. Press MENU/SELECT.
A checkmark s shown next to the current selecton. Press or toselect oN or oFF.
Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
Telephne settins
out of rANGe
KeY BeePS
oN
off
toNeS
HANdSet NAMe
Press and holdoFF/CLEar atanytme to ext themenu.
Press oFF/CLEar
at anytme to returnto the prevousscreen.
-
8/2/2019 Phone vtech 6042_manual.i2
14/62
.vtechphnes.cm 11
Bsicopertion
Telephon
esettings
Telephne settins
Edit hndset nme Press MENU/SELECT to dsplay the menu when n dle mode.
Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach HaNDSET NaME. Press MENU/SELECT.Press MUTE/rEMoVE to backspace and erase characters.
Press and hold MUTE/rEMoVE to delete the entre entry.
Press * to alternate between uppercase and lowercase.
Use the keypad to enter characters (see the chart on page 18.)
Press MENU/SELECT.
The screen dsplays STorEDand youll hear a conrmation beep.
HANdSet NAMe
lANGuAGe
eNter NAMe
HANdSet\
a
LnueTo change the language for all screen dsplays:
Press MENU/SELECT to dsplay menu when n dle mode.
Press or to reach SETUP HS. Press MENU/SELECT.
Press or to reach LaNgUagE. Press MENU/SELECT.
A checkmark s shown next to the current selecton. Press or
to choose the desred language.
Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
lANGuAGe
reSet
A handset namecan be up to 14characters only.
Only handsetdsplay screensare affected bythe languagesettng.
-
8/2/2019 Phone vtech 6042_manual.i2
15/62
.vtechphnes.cm12
Cle vicemilIf you subscrbe to vocemal servces provded by your local telephone
company, NEw VoICEMaIL wll appear on the handset dsplay and
the VoICEMaIL light on the telephone base will ash when you have
a new vocemal message. Ths feature allows you to turn off these
ndcators.
Press MENU/SELECT to dsplay the menu when n dle mode.
Press or to reach SETUP BS. Press MENU/SELECT.
Press or to reach CLr VoICEMaIL. Press MENU/SELECT. The screen dsplays INDICaTor oFF? Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
INdIcAtor off?
clr voIceMAIl
reSet
Telephne settins
Dil tpeThe dial type is preset to touch tone. If you have pulse (rotary) service,
the dal type must be changed.
Press MENU/SELECT to dsplay menu when n dle mode. Press or to reach SETUP BS. Press MENU/SELECT.
Press or to reach DIaL TyPE. Press MENU/SELECT.
A checkmark s shown next to the current selecton. Press or
to choose between ToNE and PULSE.
Press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
toNe
PulSe
dIAl tYPe
clr voIceMAIlThe clear vocemalfeature only turns
off the dsplayedNEw VoICEMaILmessage andVoICEMaIL lghton the telephonebase. It does notdelete your vocemalmessage(s). Useths feature when thetelephone ndcates
there s vocemalwhen you have noneor you have accessedyour vocemal from aremote location (whileaway from home). Ifthere s actually a newvocemal message,your local telephonecompany wll contnueto send a sgnal
whch wll cause theNEw VoICEMaILmessage n thehandset and thetelephone baseVoICEMaIL lght toash.
-
8/2/2019 Phone vtech 6042_manual.i2
16/62
.vtechphnes.cm 13
Bsicopertion
Telephon
esettings
Telephne settins
reset t defult settinsThe handset and the telephone base can be ndvdually reset to ther
default settngs by selectng rESET n the SETUP HS or SETUP BS
menus respectvely. Press MENU/SELECT to dsplay menu when n dle mode.
Press or to reach SETUP HS or SETUP BS. Press
MENU/SELECT.
Press or to reach rESET. Press MENU/SELECT.
The screen dsplays rESET? Press MENU/SELECT to conrm or
oFF/CLEar to ext to the prevous menu.
The screen dsplays STorED and youll hear a conrmation beep.
reSet
rING MelodY
reSet?
When the handsetor telephone base
settngs are resetto default, all temsstored n memorywll be deleted.Ths ncludes thedrectory and calllog entres.
Temp tne dilinIf you have pulse (rotary) service, you can change from pulse to touch
tone dalng durng a call by pressng *ToNE. Ths s useful f you needto send touch tone sgnals for access to telephone bankng or long
dstance servces.
Press /FLaSH.
Press*ToNE. Buttons pressed after ths send touch tone sgnals.
Dal the number.After hangng up, the telephone automatcally returns to pulse dal
servce.
-
8/2/2019 Phone vtech 6042_manual.i2
17/62
.vtechphnes.cm14
Bsic petin
optins hile n clls
Spekephne Press to alternate between speakerphone and normal handset use.
Mute Press MUTE/rEMoVEon the handset to slence the mcrophone durng a
conversaton. You can stll hear the caller but the caller cannot hear you.
The screen dsplays MUTE.
Press MUTE/rEMoVE agan to resume conversaton.
Mke, nse nd end clls
Press /FLaSH or , then use the keypad to dal a number.
-or-
Dial a number (press MUTE/rEMoVE to make corrections) and then press/FLaSH or .
Press /FLaSH, or any dialing keys (0-9, * or #) to answer an
ncomng call.
Press oFF/CLEar or put the handset back to the telephone base or
charger to end a call.
The call tmer wll be actvated durng a call to show call duraton.
PHoNe 00:00:10
595-9511
MUTE
Press or toadjust the lstenngvolume durng aconversaton.
Cll itinIf you subscrbe to call watng servce and you are on a call when a new call
comes n, you wll hear a beep. The caller ID nformaton wll be dsplayed
f you subscrbe to caller ID servce from your local telephone company.
Press /FLaSH on the handset to answer the ncomng call and put
the current call on hold.
Press /FLaSH at anytme to alternate between calls.
-
8/2/2019 Phone vtech 6042_manual.i2
18/62
.vtechphnes.cm 15
Bsicopertion
Bsic petin
Intecm cllThs feature allows conversaton between handsets.
Press INT on a handset and ts screen dsplays NUMBEr.
Use the keypad to select a destnaton handset. The screen of theorgnatng handset dsplays CaLLINg HaNDSET X.
The destnaton handset rngs and ts screen dsplays
CaLLINg FroM: HaNDSET X.
Press /FLaSH, or any dialing keys (0-9, * or #) on the destination
handset to answer the call.
To end an ntercom call, press oFF/CLEar on the handset or by placng
the handset back on the telephone base or charger.
Multiple hndset useWhle on a call, the person on the other handset can jon the conversaton.
Press /FLaSH or to jon the conversaton. (Only two handsets can
join the conference conversation at the same time.)
Press oFF/CLEar, or place the handset n the telephone base or charger
to drop out of the call. The external call wll not be termnated untl both
handsets hang up.
anse n extenl cll duin n intecm cllThere wll be an alert tone to sgnfy an ncomng external call durng an
ntercom call and the screen dsplays CaLL waITINg.
Dsconnect the ntercom call by pressng oFF/CLEar and the handset
wll rng.
Press /FLaSH, or any dialing keys (0-9, * or #) to answer the
ncomng call.
coNf 00:02:48
INtercoM
NuMBer
cAllING
HANdSet X
cAllING froM:
HANdSet X
For 6042/6043,press INT todrectly call theother handset. Its not necessaryto press anynumber key.
-
8/2/2019 Phone vtech 6042_manual.i2
19/62
.vtechphnes.cm16
Bsic petin
If the destnatonhandset does not
answer, pressoFF/CLEar onthe orgnatnghandset to returnto the externalcall.
Press and holdFIND HaNDSETto page handsetswhle lstenng to
messages.
Tnsfe n extenl cllAn external call can be forwarded to another handset durng a conversaton.
Press INT and put the call on hold on the orgnatng handset.
Use the keypad to select the destnaton handset and the screen dsplaysCaLLINg HaNDSET X. (For 6052/6053 only)
The destnaton handset rngs and ts screen dsplays
CaLLINg FroM: HaNDSET X.
After the destnaton handset s answered, press MENU/SELECT and
then press or to reach CoNFErENCE.
Press MENU/SELECT to let the destnaton handset jon the
conversaton.
Press MENU/SELECT and the screen dsplays END CoNFErENCE and
then press MENU/SELECT to return to the ntercom conversaton.
Durng the ntercom conversaton, press MENU/SELECT and use or
to reach oTHEr CaLL to return to the external call and put the ntercom on
hold. Repeat ths step to swtch between the external and ntercom call.
Press oFF/CLEar on the orgnatng handset to forward the external call
to the destnaton handset.
eNd coNfereNce
coNfereNceotHer cAll
otHer cAllcoNfereNce
Find hndset Press FIND HaNDSET on the telephone base to locate the handset when
n dle mode. All handsets wll rng and PagINgwill ash on the screen
of all handsets.
Press FIND HaNDSET agan or put the handsets back on the telephone
base or chargerto stop the pagng tone.
PAGING
-
8/2/2019 Phone vtech 6042_manual.i2
20/62
.vtechphnes.cm 17
adv
nced
opertion
advnced petin
eMPtY
vtecH1-595-9511
DiectThe drectory can store up to 50 entres. Each entry may consst of a
number up to 24 dgts and a name up to 15 characters.
The screen dsplays EMPTy f there s no record n the drectory. The screen dsplays FULLf the drectory s full.
revie the diect Press / to enter the drectory.
Press or to browse and press oFF/CLEar to ext.
-or-
Press MENU/SELECT to dsplay menu when n dle mode.
Press or to reach DIrECTory. Press MENU/SELECT.
Press or to reach rEVIEw. Press MENU/SELECT.
Press or to browse and press oFF/CLEar to ext.
Sech the diectEntres are sorted alphabetcally and names begnnng wth numbers
are listed rst.
An alphabetcal search can be done after enterng the drectory. Enter
the rst letter of the name using the chart on page 18. The rst name
begnnng wth that letter wll be dsplayed.For example, press 5 (JKL) once to nd Jenny, twice to nd Kristen, or
three times to nd Linda.
-or-
You can search the drectory by pressng or on the handset.
revIew
Store
dIrectorY
cAll loG
If more than 24
dgts are enteredwhen stornga telephonenumber, there wllbe an error tone.
-
8/2/2019 Phone vtech 6042_manual.i2
21/62
.vtechphnes.cm18
advnced petin
Cht f chctesUse the keypad and the chart below to enter a name (up to 15 characters). Each press of a particular
key causes the characters to be dsplayed n the followng order:
Press MUTE/rEMoVE to backspace and erase a sngle character.
Press and hold MUTE/rEMoVE to delete the entre entry.
Press and hold rEDIaL/PaUSE to insert a dialing pause (P is displayed) when entering a
telephone number.
Number Characters by number of key presses
key 1 2 3 4 5 6 7 8 9
1 space 1 * ? ! / ( )
2 A B C 2
3 D E F 3
4 G H I 4
5 J K L 56 M N O 6
7 P Q R S 7
8 T U V 8
9 W X Y Z 9
0 0
*Uppercase/lowercase
# # , , - . &
Press *repeatedly toalternate betweenuppercaseand lowercasewhen enterngcharacters.
-
8/2/2019 Phone vtech 6042_manual.i2
22/62
.vtechphnes.cm 19
adv
nced
opertion
advnced petin
Ste n ent in the diect Press MENU/SELECT twceto enter the DIrECTory.
Press or to reach STorE and then press MENU/SELECT.
The screen dsplays ENTEr NUMBEr. Use the keypad to enter thenumber and then press MENU/SELECT.
The screen dsplays ENTErNaME. Use the keypad to enter the
characters and then press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
Dil diect ent Press / to enter the drectory.
Press or to scroll to the desred entry, or use the alphabetcal
search to nd it.
Press /FLaSH or to dal.
-or-
Press MENU/SELECT to dsplay menu when n dle mode.
Press or to reach DIrECTory. Press MENU/SELECT.
Press or to reach rEVIEw. Press MENU/SELECT.
Press or to scroll to the desred entry, or use the alphabetcal
search to nd it.
Press /FLaSH or to dal.
eNter NuMBer
eNter NAMe
Store
revIew
Stored
a
-
8/2/2019 Phone vtech 6042_manual.i2
23/62
.vtechphnes.cm20
advnced petin
Delete ne ll enties in the diect
Press / or MENU/SELECT three tmes to enter the drectory. Press or to scroll to the desred entry.
T delete n ent
Press MUTE/rEMoVE.
The screen dsplays DELETED and there is a conrmation beep.
T delete ll enties
Press and hold MUTE/rEMoVE.
The screen dsplays DELETE aLL? Press MENU/SELECT.
The screen dsplays DELETED and youll hear a conrmation beep.
Edit n ent in the diect Press / or MENU/SELECT three tmes to enter the drectory.
Press or to scroll to the desred entry or use the alphabetcal
search to nd the number. Press MENU/SELECT. The screen dsplays ENTEr NUMBEr. Use MUTE/rEMoVE and the
keypad to edt the number and press MENU/SELECT.
The screen dsplays ENTEr NaME. Use MUTE/rEMoVEand thekeypad to edt the name and then press MENU/SELECT.
The screen dsplays STorEDand youll hear a conrmation beep.
delete All?
deleted
eNter NuMBer
eNter NAMe
Stored
a
Press oFF/CLEarto return to the
prevous screen.Press and holdoFF/CLEar to extthe menu f you donot want to deleteall the entres.
-
8/2/2019 Phone vtech 6042_manual.i2
24/62
.vtechphnes.cm 21
adv
nced
opertion
abut clle ID infmtinIf you subscbe to caller ID servce from your local telephone company, ths feature dsplays the name
and telephone number of the caller before answering a call (even when you are on another call). The
caller ID features of ths product wll work only f you subscrbe to caller ID servce and both you and
the caller are n areas offerng caller ID servce, and f both telephone companes use compatble
equpment.
Contact your local telephone company f:
you have both caller ID and call waiting, but as separate services (you may need combined service),
you have only caller ID servce, or only call watng servce,
you do not subscrbe to caller ID or call watng servces but wsh to try them.
There may be fees for these servces, and they may not be avalable n all areas.
Ths product can be used wthout subscrbng to ether caller ID or combned caller ID wth call watng
servce, although the caller ID features of ths product wll not functon.
advnced petin
-
8/2/2019 Phone vtech 6042_manual.i2
25/62
.vtechphnes.cm22
advnced petin
Cll lThe nformaton of the caller wll be dsplayed f you subscrbe to caller
ID servce from your local tephone company.
The call log can store up to 50 entres.Each entry may consst of a number up to 20 dgts and a name up to
15 characters. If the number conssts of more than 20 dgts, the last 20
dgts wll be dsplayed and stored. If the name conssts of more than
15 characters, the rst 15 characters will be displayed and stored.
Entres are dsplayed n chronologcal order wth the newest entry
rst.
When the call log s full, the oldest entry wll be deleted to make room
for the new ncomng call nformaton.
The screen dsplays EMPTy f there s no record n the call log.
The screen dsplays NEw if there are new call log entries (missed
and unread calls).
Duplicate or anonymous calls (no caller ID information) will be stored
n the call log.
revie the cll l Press CID/ to enter the call log.
-or-Press MENU/SELECT. Press or to select CaLL Log.
Press MENU/SELECT and then press or to browse through the
entres.
The name (if available), number, date and time of the incoming call
are dsplayed on the screen.
Due to regonalservce dfferences,
the caller IDnformaton maynot be avalablefor every ncomngcall. In addton,the callers mayntentonally blockther name and/ortelephone number.
The tme s
automatcally setand updated wthncomng caller IDnformaton f yousubscrbe to thsservce.
JoHNNY fu
2-345-6789New
05:27PM 11/23
eMPtY
-
8/2/2019 Phone vtech 6042_manual.i2
26/62
.vtechphnes.cm 23
advnced
opertion
advnced petin
Ste numbe fm the cll l Press CID/ to enter the call log.
-or-
Press MENU/SELECT. Press or to select CaLL Log.
Press MENU/SELECT and then press or to scroll to the desred
entry.
Press MENU/SELECT and the screen dsplays ENTEr NaME.
Use the keypad to enter the name and then press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
Whle revewngthe call log, press
# repeatedly todsplay the otherdalng optons.The avalableoptions are: (1+ area code +number, area code+ number, 1 +number, numberonly). The various
dalng optons are:
eNter NAMe
Stored
595-95111-595-9511
800-595-95111-800-595-9511
Dil cll l numbe Press CID/ to enter the call log.
-or-
Press MENU/SELECT. Press or to select CaLL Log. Press MENU/SELECT and then press or to scroll to the desred
entry.
Press /FLaSH or to dal.
a
-
8/2/2019 Phone vtech 6042_manual.i2
27/62
.vtechphnes.cm24
advnced petin
Delete ne ll enties in the cll l Press CID/ to enter the call log.
-or-
Press MENU/SELECT. Press or to select CaLL Log.T delete ne ent
Press or to scroll to the desred entry and then press
MUTE/rEMoVE.
The screen dsplays DELETEDand youll hear a conrmation beep.
T delete ll enties
Press and hold MUTE/rEMoVE when n the CaLL Log.
The screen dsplays DELETE aLL? Press MENU/SELECT.
The screen dsplays DELETEDand youll hear a conrmation beep.
deleted
delete All?
Press oFF/CLEarto return to the
prevous screen.Press and holdoFF/CLEar to extthe menu f you donot want to deleteall the entres.
-
8/2/2019 Phone vtech 6042_manual.i2
28/62
.vtechphnes.cm 25
advnced
opertion
advnced petin
redilThe redal lst can store up to 10 of the most recently daled numbers.
When there are already 10 entres n the redal lst, the oldest entry
wll be deleted to make room for the new one. The screen dsplays EMPTy f there s no record on the lst.
revie edil Press rEDIaL/PaUSE to enter the redal lst.
Press or to browse through the entres.
Ste numbe fm edil t the diect Press rEDIaL/PaUSE to enter the redal lst.
Press or to scroll to the desred entry. Press MENU/SELECT.
The screen dsplays ENTEr NaME.
Use the keypad to enter the name and then press MENU/SELECT.
The screen dsplays STorED and there is a conrmation beep.
-
8/2/2019 Phone vtech 6042_manual.i2
29/62
.vtechphnes.cm26
Dil numbe fm edil Press rEDIaL/PaUSE to enter the redal lst.
Press or to scroll to the desred entry.
Press /FLaSH or to dal.
Delete ne ll enties fm edil Press rEDIaL/PaUSE to enter the redal lst.
T delete ne ent
Press or to scroll to the desred entry and then press
MUTE/rEMoVE.
The screen dsplays DELETED and youll hear a conrmation beep.
T delete ll enties
Press and hold MUTE/rEMoVE.
The screen dsplays DELETE aLL? Press MENU/SELECT.
The screen dsplays DELETED and youll hear a conrmation beep. delete All?
deleted
advnced petin
Press oFF/CLEarto return to the
prevous screen.Press and holdoFF/CLEar toext the menu fyou do not wantto delete all theentres.
-
8/2/2019 Phone vtech 6042_manual.i2
30/62
.vtechphnes.cm 27
advnced
opertion
ansein sstem petin
Messe cpcitThe answerng system can record up to 99 messages, dependng on the length of each message.
The total maxmum recordng tme s 15 mnutes and each ndvdual message can be up to four
mnutes long. Messages wll reman avalable for replay untl they are deleted.
X/DELETEPress to delete message currently playng.When dle, press and hold to delete allmessages (page 32).
/PLay/SToP
Press to play or stop playngmessages (page 32).
/rEPEaT
Press to repeat a message(page 32).
Messe indShows the status andnumber of messages(page 34).
aNNCPress to play or record the outgong
announcement (page 31).
aNS oN/oFFPress to turn on or off the
answering system (page 28).
/ /VoLUME+/-
Press to adjust volume
during playback (page 32).Press to adjust callscreening volume (page 32).Press to adjust rngervolume whle the telephoneis ringing (page 29).
/SKIP
Press to skp to nextmessage (page 32).
-
8/2/2019 Phone vtech 6042_manual.i2
31/62
.vtechphnes.cm28
ansein sstem petin
activte the nsein sstemThe aNS oN/oFF must be on (the button light will be on) in order for the
machne to answer calls and record messages. If the button lght s of f then
calls wll not be answered.
To turn on/off the answerng system, press aNS oN/oFF to choose between
on and off.
Use the volume control button on the telephone base to adjust the volume
at anytme durng the setup procedure.
When aNS oN/oFFs turned off, your
telephone wll rng10 tmes beforeanswerng andpromptng for theremote accesscode.
Set numbe f insThs feature allows you to select the number of tmes the telephone rngs before the answerng system
answers. You can choose from two, four, sx, eght rngs or toll saver. When toll saver s actvated, the
answerng system answers after two rngs when there are new messages, and after sx rngs whenthere are no new messages.
Press No. oF rINgS when n dle mode and the system announces the current settng.
The system announces To change the setting, press number of rings again.
Press No. oF rINgS repeatedly untl the desred settng s announced. If you do not press the
aNNC button for about two seconds, the setting will be saved and there is a conrmation beep.
Set telephne bse dte nd timeThe answerng system announces the day and tme the message was receved before playng each
message. Set the date and tme before usng the answerng system so all messages are dated correctly.Settng handset date and tme wll smultaneously update the telephone base date and tme.
The system wll announce Please set the handset clock before message playback f you do not set
the date and tme before usng ths system.
-
8/2/2019 Phone vtech 6042_manual.i2
32/62
.vtechphnes.cm 29
advnced
opertion
ansein sstem petin
BS MelodYBS rINGer vol
MelodY 1MelodY 2
SetuP BSdAte/tIMe
Set telephne bse meldThere are sx rng melodes to choose from.
Press MENU/SELECT on the handset to dsplay menu when n dle
mode.
Press or to reach SETUP BS. Press MENU/SELECT.
Press or to reach BS MELoDy. Press MENU/SELECT and a
checkmark s shown next to the current melody.
Press or to scroll through the choces and a sample of each
melody wll be played on the telephone base.
Press MENU/SELECT to conrm selection.
The screen dsplays STorED and youll hear a conrmation beep.
Set telephne bse ine vlume
You can adjust the telephone base rnger volume to one of eght dfferent
levels, or turn the telephone base rnger off.
Press MENU/SELECT on the handset n dle mode.
Press or to reach SETUP BS. Press MENU/SELECT.
Press or to reach BS rINgEr VoL. Press MENU/SELECT.
Press or to scroll through the choces and a sample of each rng
volume wll be played at the telephone base.
Press MENU/SELECT to conrm selection.
The screen dsplays STorED and youll hear a conrmation beep.
You can also adjust the telephone base rnger volume by pressng VoL+/-
on the telephone base whle the telephone s rngng.
The rng melodyfor the handset
s set separatelyfrom the telephonebase rng melody.See page 8 to setthe handset rngermelody.
The volume of thehandset rngers set separatelyfrom the telephone
base rnger. Seepage 9 to changethe handset rngervolume.
-
8/2/2019 Phone vtech 6042_manual.i2
33/62
.vtechphnes.cm30
ansein sstem petin
Change personal identifcation number (PIN)A four-digit security code is required for remote access to the answering
system from any touch tone telephone. The factory default code s 0000.
To change the PIN on your telephone:
Press MENU/SELECT on the handset n dle mode.
Press or to reach SETUP BS. Press MENU/SELECT.
Press or to reach CHaNgE ITaD PIN. Press
MENU/SELECT.
The screen dsplays ENTEr PIN.
Enter the PIN (default 0000) then press MENU/SELECT.
The screen dsplays NEw PIN.
Enter the desired PIN and press MENU/SELECT.
The screen dsplays rEPEaT PIN.
Enter the new PIN again and press MENU/SELECT.
The screen dsplays STorED and youll hear a conrmation beep.
If a wrong PIN is entered, the screen displays wroNg PIN, retry
after two seconds.
cHANGe ItAd PIN
dIAl tYPe
eNter PIN
eNter PIN****
New PIN
rePeAt PIN
-
8/2/2019 Phone vtech 6042_manual.i2
34/62
.vtechphnes.cm 31
advn
ced
opertion
ansein sstem petin
outin nnuncementsAn outgong announcement s the message callers hear when calls are
answered by the answerng system.
The telephone s preset wth an announcement that answers calls wth
Hello, please leave a message after the tone. You can use ths defaultannouncement, or replace t wth your own.
The annoucementcan be up to 90
seconds n length.When yourown recordedannoucements deleted, callswll be answeredwth the presetannouncement.
Pl the nnuncement Press aNNC n dle mode. The system announces Announcement, press
play or press announcement again to record a new announcement.
Press PLay/SToP and the announcement wll be played.
recd u n nnuncement
PressaNNC n dle mode, and the system announces Announcement, pressplay or press announcement again to record a new announcement.
Press aNNC agan and the system announces Record after the tone,
pressstopwhen you are done.
After the tone, speak towards the mcrophone at the bottom front of the
telephone base from about nne nches away.
Press /PLay/SToP when nished.
The answerng system wll automatcally playback the newly recorded
announcement and there will be a conrmation tone. Press /PLay/
SToP to stop the playback at any tme.If you do not lke the announcement just recorded, press aNNC to record
again before the conrmation tone.
a i i
-
8/2/2019 Phone vtech 6042_manual.i2
35/62
.vtechphnes.cm32
ansein sstem petin
Messages canonly be deleted
after they areplayed.
When theanswerngmachne srecordngan ncomngmessage or ndle mode, the callscreenng volume
can be adjustedby pressngVoL+/- on thetelephone base.
Messe plbck Press /PLay/SToP to lsten to messages. Press /PLay/SToP
agan to stop playback.
If there are new messages, the system wll announce the number of
new and old messages then play the new messages only (oldest rst).
If there are no new messages, the system wll announce the numberof old messages and playback all messages (oldest rst).
Before each message s played, the day and tme t was receved wll
be announced.
optins duin plbck Press / /VoLUME to adjust the speaker volume.
Press /SKIP to skp to the next message.
Press /rEPEaT to repeat the message currently playng.
Press X/DELETE to delete the current message. The system wll
advance to the next message.
Delete ll messes Press and hold X/DELETE when n dle mode.
The system announces All old messages deleted.
Delete u nnuncement Press aNNC n dle mode, and the system announces Announcement,
press play or press announcement again to record a new
announcement.
Press /PLay/SToP and then press DELETE when the systems playng the outgong announcement. The system announces
Announcement deleted.
a i t ti
-
8/2/2019 Phone vtech 6042_manual.i2
36/62
.vtechphnes.cm 33
advn
ced
opertion
ansein sstem petin
Durng remoteaccess, f no key
s pressed wthneght seconds,the remoteaccess call sautomatcallydsconnected.
remte ccessYou can access many features of your answerng system remotely from any touch tone telephone.
A four-digit security code is required to access the system and the factory default code is 0000; see
page 30 to change t. To enter remote access:
Dal your telephone number from any touch tone telephone.
When the system answers and plays the outgong announcement, press* followed by theremote access code.
After you enter the remote access code, the system wll play any new messages and then play
the menu of commands.
0 To end the call1 To play all messages
2 To play new messages
3 To delete the message
33 To delete all old messages
4 To repeat the prevous message
5 To stop playng the message
6 To skp the message7 To turn the answerng system on
8 To turn the answerng system off
9 To repeat help
remte ccess cmmnds:
a i t ti
-
8/2/2019 Phone vtech 6042_manual.i2
37/62
.vtechphnes.cm34
ansein sstem petin
The message counter usually dsplays the total number of ncomng messages.
See the lst below for explanatons of other dsplays n ths counter.
Messe ind displs
0 No messages.
0 (ashing) The clock needs to be set.
1-99 Total number of old message(s) recorded.
1-99 (ashing) Total number of message(s) recorded, at least one is new.
1-99& F(alternating) Memory is full with total number of messages recorded.
1-90 (counting) Elapsed time while recording an annoucenment.
1-99 Current message number durng message playback.0-8 Current volume level whle adjustng.
02, 04, 06, 08, tS Current number of rngs whle settng.
-- System s answerng a call.
-- (ashing) System is being setup or initialized, or being accessed remotely.
Hndset nd telephne bse indicts
-
8/2/2019 Phone vtech 6042_manual.i2
38/62
.vtechphnes.cm 35
appendix
Hndset nd telephne bse indicts
Hndset icns
Telephne bse lihts
Hndset liht
Rnger off.
(Battery indicator) Cycles (low, medium, and full) when handset battery is charging.
Flashes when the battery power s low.
On when the handset speakerphone s n use.
IN USE Flashes when there s an ncomng call.
Flashes when another handset connected to the same lne s n use.
On when the handset s n use.
VoICEMaIL Flashes when there is a new network message (a subscription servicefrom your local telephone company is required).
CHargE On when the handset s n the telephone base.
aNS oN/oFF On when the answerng system s on.
Hndset displ sceen messes
-
8/2/2019 Phone vtech 6042_manual.i2
39/62
.vtechphnes.cm36
Hndset displ sceen messesDispl: when:
cAll There s an ncomng call.
cAllING HANdSet X Callng another handset.
cAllING froM:HANdSet X Other handset s callng.
cHArGING A handset wth low battery has been placed on the telephone base torecharge.
coNNectING... The cordless handset s searchng for the telephone base.
eMPtY There are no entres n the call log, drectory, or redal lst.
eNded You have just ended a call.
full The drectory s full.
INtercoM The handset s on an ntercom call.
lINe IN uSe Another handset connected to the same lne s n use.
low BAtterY The battery needs to be recharged.
Mute The mcrophone s muted temporarly durng a conversaton.
New There are un-reviewed calls in the call log.
New voIceMAIl There s new vocemal message.
Not AvAIlABle There s no lne or the handset s out of range from the telephone base.-or-
If one handset s already vewng the call log and another handsetattempts to revew t.
No lINe There s no telephone lne connected.
Hndset displ sceen messes
-
8/2/2019 Phone vtech 6042_manual.i2
40/62
.vtechphnes.cm 37
appendix
Hndset displ sceen messes
Displ: when:
PAGING The handset locator has been actvated or the handset s beng paged.
PHoNe The handset s n use.
PlAce IN cHArGer The battery s very low. The handset should be placed on the telephonebase to recharge.
wArNING
cHecK BAtterY!
The battery s not nstalled or not nstalled properly n the handset.
-or -
The battery needs to be replaced.
-or -
An ncorrect battery has been nstalled by mstake. Use only the
suppled VTech battery, or equvalent.
Displ: when:
PrIvAte NAMe The caller s blockng name nformaton.
PrIvAte NuMBer The caller s blockng telephone number nformaton.
PrIvAte cAller The caller s blockng name and number nformaton.
uNKNowN NAMe Ths callers name s unavalable.
uNKNowN NuMBer Ths callers number s unavalable.
uNKNowN cAller No call information is available about this caller.
loNG dIStANceor
l (before callers number)
Ths s a long dstance call.
Cll l displ messes
-
8/2/2019 Phone vtech 6042_manual.i2
41/62
.vtechphnes.cm38
Btteafte the btte is full ched f 16 hus, u cn expect the fllin pefmnce:
Operaton Operatng tme
While in use (talking) 10 hours
While not in use (standby*) 100 hours
*Handset is off the telephone base but not in use.
The battery needs chargng when:
A new battery s nstalled n the handset.
Battery indicator on screen is ashing.
CaUTIoN:
1. Use only the supplied battery (part number 89-1326-00-00) or equivalent. To order a replacement, visit our website atwww.vtechphones.com or call 1 (800) 595-9511. In Canada, visit www.vtechcanada.com or call 1 (800) 267-7377.
2. Do not dispose of the battery in a re. Check with local waste management codes for special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause burns or injury to the eyes or
skn. The electrolyte may be toxc f swallowed.
4. Exercse care n handlng batteres n order not to create a short crcut by lettng them come nto contact wth conductve
materals such as rngs, bracelets, and keys. The battery and/or conductor may overheat and cause burns.
5. Charge the battery(ies) provided with or identied for use with this product only in accordance with the instructions and
limitations specied in this manual.warNINg:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO WATER OR ANY TYPE OF MOISTURE.
Imptnt sfet instuctins
-
8/2/2019 Phone vtech 6042_manual.i2
42/62
.vtechphnes.cm 39
appendix
Imptnt sfet instuctinsWhen usng your telephone equpment, basc safety precautons should always be followed:1. Read and understand all nstructons.
2. Follow all warnngs and nstructons marked on the product.
3. Unplug ths product from the wall outlet before cleanng. Do not use lqud or aerosol cleaners. Use a damp cloth for cleanng.
4. Do not use this product near water (for example, near a bathtub, kitchen sink, or swimming pool).
5. Do not place ths product on an unstable surface such as a table, shelf or stand. Ths product may fall, causng serous damage.
6. Slots and openngs n the back or bottom of the telephone base and handset are provded for ventlaton. To protect them from overheatng, these openngs must not beblocked by placng the product on a soft surface such as a bed, sofa or rug. Ths product should never be placed near or over a radator or heat regster. Ths product shouldnot be placed n an area where proper ventlaton s not provded.
7. Ths product should be operated only from the type of power source ndcated on the markng label. If you are not sure of the type of power supply n your home, consult yourdealer or local power company.
8. Do not allow anythng to rest on the power cord. Do not nstall ths product where the cord may be walked on.
9. Never push objects of any kind into this product through slots in the telephone base or handset as they may touch dangerous voltage points or create a short circuit that couldresult in a risk of re or electric shock. Never spill liquid of any kind on the product.
10. To reduce the rsk of electrc shock, do not dsassemble ths produc t, but take t to an authorzed servce faclty. Openng or removng parts of the telephone base or handset othe rthan specied access door s may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used .
11. Do not overload wall outlets and extension cords as this can result in the risk of re or electri c shock.
12. Unplug ths product from the wall outlet and refer servcng to an authorzed servce faclty under the followng condtons:
A. When the power supply cord or plug s damaged or frayed.B. If lqud has been splled onto the product.
C. If the product has been exposed to ran or water.
D. If the product does not operate normally by followng the operatng nstructons. Adjust only those controls that are covered by the operaton nstructons, as mproperadjustment of other controls may result n damage and often requres extensve work by an authorzed techncan to restore the product to normal operaton.
E. If the product has been dropped and the telephone base and/or handset has been damaged.
F. If the product exhbts a dstnct change n performance.
13. The power unit is intended to be correctly oriented in a vertical or oor mount posit ion. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, anunder-the-table or cabinet outlet.
14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.
15. Do not use the telephone to report a gas leak n the vcnt y of the leak.
16. Only put the handset of your telephone next to your ear when t s n normal talk mode.
CAUTION: Use only the power adapter provided with this product. To purchase, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go towww.vtechcanada.com or call 1 (800) 267-7377.
SAVE THESE INSTRUCTIONS
i
-
8/2/2019 Phone vtech 6042_manual.i2
43/62
.vtechphnes.cm40
Tubleshtin
Problem SuggestonMy telephone does not
work at all.
Make sure the battery is installed and charged correctly (page 2). For optimum daily
performance, return the cordless handset to the telephone base or charger after use.
Make sure the power adapter s securely plugged nto an outlet not controlled by a wall
swtch.
Make sure the telephone line cord is plugged rmly into the telephone base and the wall jack.
Unplug the unts electrcal power. Wat for approxmately 15 seconds, then plug t back n.
Allow up to one mnute for the cordless handset and telephone base to synchronze.
Charge the battery n the cordless handset for at least 16 hours.
Remove and re-insert the battery. If that still does not work, it may be necessary to purchase
a new battery.
Dsconnect the telephone base from the jack and plug n a workng telephone. If ths telephone
does not work, the problem s probably n the wrng or the local servce. Call the local telephone
company.
Low BaTTEry s
dsplayed on screen.
Place the handset n the telephone base or charger for rechargng.
Remove and re-install the battery and use it normally until fully discharged, then recharge the
handset on the telephone base or charger for 16 hours.
If the above measures do not correct the problem, the battery may need to be replaced.
If you have difculty with your telephone, please try the suggestions below. For Customer Service, visit our website at www.
vtechphones.com, or call 1 (800) 595-9511; in Canada, call 1 (800) 267-7377.
T bl h ti
-
8/2/2019 Phone vtech 6042_manual.i2
44/62
.vtechphnes.cm 41
appendix
Problem SuggestonThe battery does not
charge n the handset
or the handset batterydoes not accept
charge.
Make sure the handset s placed n the telephone base or charger correctly. The CHargE
lght on the telephone base or charger should be on.
Remove the battery from the handset and then re-install it in the handset. Put the handsetback to the telephone base or charger and charge for 16 hours.
If the cordless handset s n the charger or n the telephone base but the CHargE lght s not
on, see The CHargE liht is ff n ths secton.
It may be necessary to purchase a new battery. Please see the Btte secton of ths users
manual (page 38).
The telephone mght be malfunctonng. Please see thewnt secton of ths users manual
(page 51) for further instruction.
The CHargE lght s
off.
Clean the charging contacts on the cordless handset(s) and telephone base each month using
a pencil eraser or a dry non-abrasive fabric.
Make sure the power adapter and telephone lne cords are plugged n correctly and
securely.
Unplug the power adapter. Wat for 15 seconds before pluggng t back n. Allow up to one
mnute for the cordless handset and telephone base to reset.
The telephone mght be malfunctonng. Please see thewnt secton of ths users manual
(page 51) for further instruction.
Tubleshtin
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
45/62
.vtechphnes.cm42
Tubleshtin
Problem SuggestonThere s no dal tone. Frst, try all the above suggestons.
Move the cordless handset closer to the telephone base. It mght be out of range.
The telephone lne cord mght be malfunctonng. Try nstallng a new telephone lne cord.
Dsconnect the telephone base from the telephone jack and connect a dfferent telephone. If
there s no dal tone on the other telephone ether, the problem s n your wrng or local servce.
Contact your local telephone company.
My handset dsplays
CoNNECTINg...
Move the handset closer to the telephone base. You mght have moved out of range.
My handset dsplays
NoT aVaILaBLE
Move the handset closer to the telephone base. You mght have moved out of range.
Make sure no other handset s revewng the call log when an attempt s dened.
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
46/62
.vtechphnes.cm 43
appendix
Tubleshtin
Problem SuggestonThe telephone does
not rng when there s
an ncomng call.
Make sure the ringer is on (see page 9 for handset and page 29 for telephone base).
Make sure the telephone line cord and power adapter are plugged in properly (page 3).
The cordless handset may be too far from the telephone base. Move t closer to the telephone
base.
There may be too many extenson telephones on the telephone lne to allow all of them to rng
smultaneously. Try unpluggng some of them.
If the other telephones n your home are havng the same problem, the problem s n the wrng
or local service. Contact the local telephone company (charges may apply).
Other electronc products can cause nterference to your cordless telephone. Try nstallng your
telephone as far away as possble from the followng electronc devces: wreless routers, rados,
rado towers, pager towers, cellular telephones, dgtal telephones, ntercoms, room montors,televsons, VCRs, personal computers, ktchen applances, and other cordless telephones.
Test a workng telephone at the telephone jack. If another telephone has the same problem, the
problem is in the telephone jack. Contact your local telephone company (charges may apply).
The telephone lne cord mght be malfunctonng. Try nstallng a new telephone lne cord.
Remove and re-insert the battery and place the cordless handset in the telephone base.
Wat for the cordless handset to synchronze wth the telephone base. Allow up to one mnute
for ths to take place.
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
47/62
.vtechphnes.cm44
Tubleshtin
Problem SuggestonI cannot dal out. Frst, try all the above suggestons.
Make sure there s a dal tone before dalng. It s normal f the cordless handset takes a second
or two to synchronze wth the telephone base before producng a dal tone. Wat an extrasecond before dalng.
Make sure the telephone is set to the correct dial type (pulse dial or tone dial) for the service in
your area. See Dil tpe on page 12 to set the dal type.
If the other telephones n your home are havng the same problem, the problem s n the wrng
or local service. Contact your local telephone company (charges may apply).
Eliminate any background noise. Noise from a television, radio, or other appliances may cause
the telephone not to dial out properly. If you cannot eliminate the background noise, rst try
mutng the cordless handset before dalng, or dalng from another room n your home wthless background nose.
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
48/62
.vtechphnes.cm 45
appendix
Tubleshtin
Problem SuggestonThere s nose
or nterference
durng a telephoneconversaton.
My calls cut n and out
when I am usng the
cordless handset.
The handset may be out of range. Move t closer to the telephone base.
Applances or other cordless telephones plugged nto the same crcut as the telephone base
can cause nterference. Try movng the applance or telephone base to another outlet. Other electronc products can cause nterference to your cordless telephone. Try nstallng your
telephone as far away as possble from the followng electronc devces: wreless routers, rados,
rado towers, pager towers, cellular telephones, dgtal telephones, ntercoms, room montors,
televsons, VCRs, personal computers, k tchen applances, and other cordless telephones.
If your telephone is plugged in with a modem or a surge protector, plug the telephone (or
modem/surge protector) into a different location. If this solves the problem, re-locate your
telephone or modem farther apart from each other, or use a dfferent surge protector.
The layout of your home or ofce might be limiting the operating range. Try moving the telephonebase to another locaton, preferably a hgher locaton for better recepton.
Dsconnect the telephone base from the modular jack and plug n a corded telephone. If calls
are stll not clear, the problem s probably n the wrng or local servce. Contact the local
telephone company (charges may apply).
If the other telephones n your home are havng the same problem, the problem s n the wrng
or local service. Contact the local telephone company (charges may apply).
Do you have DSL service? If yes, you need to have a DSL lter installed at every telephone jack
that has a telephone connected to it. Contact your DSL service provider for lter information.
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
49/62
.vtechphnes.cm46
Tubleshtin
Problem SuggestonI hear other calls when
usng the telephone.
Dsconnect the telephone base from the telephone jack. Plug n a dfferent telephone. If there are
stll other calls, the problem s probably n the wrng or local servce. Call your local telephone
company.
I hear nose n the
cordless handset, and
none of the keys or
buttons work.
Make sure the telephone lne cord s plugged n securely.
Remove and re-insert the battery.
My caller ID features are
not workng properly
Caller ID s a subscrpton servce. You must subscrbe to ths servce from your local telephone
company for ths feature to work on your telephone.
The caller may not be callng from an area whch supports caller ID. Both you and the callers telephone companes must use equpment whch are compatble wth
caller ID servce.
If you subscribe to DSL service, install a DSL lter to the telephone line between the telephone
base and the telephone line jack. Contact your DSL service provider for lter information.
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
50/62
.vtechphnes.cm 47
appendix
Problem SuggestonThe system does
not receve caller ID
or the system doesnot dsplay caller ID
durng call watng.
Make sure you subscrbe to caller ID wth call watng features provded by the local telephone
company.
The caller may not be callng from an area whch supports caller ID. Both you and the callers telephone companes must use equpment whch are compatble wth
caller ID servce.
If you subscribe to DSL service, install a DSL lter to the telephone line between the telephone
base and the telephone line jack. Contact your DSL service provider for lter information.
The answerng system
does not answer after
the correct number of
rngs.
Make sure the answerng system s on. When the answerng system s on, the red lght on the
aNSwEr oN/oFF key should be lt.
If toll saver s actvated, the number of rngs changes to two when there are new messages
waiting (see page 28).
If the memory s full or f the answerng system s off, the system wll answer after ten rngs.
In some cases, the answerng system wll be affected by the rngng system used by the local
telephone company.
The announcement
message s not clear.
When recordng the announcement, make sure you speak n a normal tone of voce about nne
nches from the telephone base.
Make sure there is no background noise (television, music, trafc, etc.) when recording.
Tubleshtin
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
51/62
.vtechphnes.cm48
Problem SuggestonThe answerng system
does not record
messages.
Make sure the answerng system s on.
The messages on the
answerng system are
ncomplete.
If a caller leaves a very long message, part of t may be lost when the system dsconnects the
call after four mnutes.
If the caller pauses for more than ve consecutive seconds, the system stops recording and
dsconnects the call.
If the memory on the system becomes full durng a message, the system stops recordng and
dsconnects the call.
If the callers voce s very soft, the system may stop recordng and dsconnect the call.
The messages on
the system are very
difcult to hear.
Press / /VoLUME on the telephone base to ncrease the speaker volume.
The answerng system
does not respond to
remote commands.
Make sure your remote access code is correct (page 33).
Make sure you are calling from a touch-tone telephone. When dialing a number, there should
be tones. If there are clicks, then it is not a touch-tone telephone and cannot activate the
answerng system.
The answerng system may not detect the remote access code when the announcement s
playng. Wat untl the announcement s over before enterng the code.
There may be interference on the telephone line you are using. Press the keypad keys rmly
when dalng.
Tubleshtin
Tubleshtin
-
8/2/2019 Phone vtech 6042_manual.i2
52/62
.vtechphnes.cm 49
appendix
Tubleshtin
Problem SuggestonMy cordless handset
beeps and s not
performng normally.
Make sure the power cord s securely plugged nto the telephone base. Plug the unt nto a
dfferent workng electrcal outlet not controlled by a wall swtch.
Move the cordless handset closer to the telephone base. It may be out of range. Reset the telephone base by unpluggng the unts electrcal power. Wat for 15 seconds and
plug t back n agan. Allow up to one mnute for the cordless handset and the telephone base
to synchronze.
Other electronc products can cause nterference to your cordless telephone. Try nstallng
your telephone as far away from these electronc devces as possble: wreless routers, rados,
rado towers, pager towers, cellular telephones, ntercoms, room montors, televsons, personal
computers, ktchen applances and other cordless telephones.
Common cure forelectronc equpment
If the unt s not respondng normally, try puttng the cordless handset n the telephone baseor the charger. If it does not seem to respond, try the following (in the order listed):
Dsconnect the power to the telephone base.
Dsconnect the battery on the cordless handset.
Wat a few mnutes before connectng power to the telephone base.
Re-install the battery and place the cordless handset into the telephone base or charger.
Wat for the cordless handset to synchronze ts connecton wth the telephone base. Allow up
to one mnute for ths to take place.
opetin ne
-
8/2/2019 Phone vtech 6042_manual.i2
53/62
.vtechphnes.cm50
opetin neThis cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base cancommunicate over only a certain distance ----which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or ofce. When the handset s out of range, the handset wll dsplay CoNNECTINg. The user can access the handset drectory, and certan parts of the menu system, .e.handset settng, but not the tme settng and telephone base settng. NoT aVaILaBLE wll be dsplayed f access s dened.
If there s a call whle the handset s out of range, t mght not rng, or f t does rng, the call mght not connect well when you press /FLaSH. Move closer to the
telephone base, then press /FLaSH to answer the call.If the handset moves out of range durng a telephone conversaton, there mght be nterference.
To mprove recepton, move closer to the telephone base.
MintennceTkin ce f u telephne
Your cordless telephone contans sophstcated electronc parts, so t must be treated wth care.
avid uh tetment
Place the handset down gently. Save the orgnal packng materals to protect your telephone f you ever need to shp t.
avid te
Your telephone can be damaged f t gets wet. Do not use the handset outdoors n the ran, or handle t wth wet hands. Do not nstall the telephone base near asnk, bathtub or shower.
Electicl stms
Electrcal storms can sometmes cause power surges harmful to electronc equpment. For your own safety, take cauton when usng electrc applances durng storms.Clenin u telephne
Your telephone has a durable plastc casng that should retan ts luster for many years. Clean t only wth a soft cloth slghtly dampened wth water or a mld soap.Do not use excess water or cleanng solvents of any knd.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the telephone base should fall into water, DO NOTRETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
abut cdless telephnesPivc: The same features that make a cordless telephone convenent create some lmtatons Telephone calls are transmt ted between the telephone base and
-
8/2/2019 Phone vtech 6042_manual.i2
54/62
.vtechphnes.cm 51
appendix
Pivc: The same features that make a cordless telephone convenent create some lmtatons. Telephone calls are transmt ted between the telephone base andthe cordless handset by rado waves, so there s a possblty that the cordless telephone conversatons could be ntercepted by rado recevng equpment wthnrange of the cordless handset. For ths reason, you should not thnk of cordless telephone conversatons as beng as prvate as those on corded telephones.
Electicl Pe: The telephone base of ths cordless telephone must be connected to a workng electrcal outlet. The electrcal outlet should not be controlledby a wall swtch. Calls cannot be made from the cordless handset f the telephone base s unplugged or swtched off, or f the electrcal power s nterrupted.
Ptentil TV Intefeence: Some cordless telephones operate at frequences that may cause nterference to televsons and VCRs. To mnmze or preventsuch nterference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If nterference s experenced, movng the cordless
telephone farther away from the TV or VCR wll often reduce or elmnate the nterference.recheble Btteies: This product contains either Nickel-Cadmium or Nickel-Metal Hydride rechargeable batteries. Exercise care in handling batteries inorder not to create a short crcut wth conductng materal such as rngs, bracelets, and keys. The battery or conductor may overheat and cause harm. Observeproper polarty between the battery and the battery charger.
Nickel-Metl Hdide recheble Btteies: Dspose of these batteres n a safe manner. Do not burn or puncture. Lke other batteres of ths type, fburned or punctured, they could release caustc materal whch could cause njury.
wntwht des this limited nt cve?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories providedin the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used
normally and n accordance wth the Product operatng nstructons. Ths lmted warranty extends only to the Consumer for Products purchased and used n theUnted States of Amerca and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?
Durng the lmted warranty perod, VTechs authorzed servce representat ve wll repar or replace at VTechs opton, wthout charge, a Materally Defectve Product . Ifwe repar the Product, we may use new or refurbshed replacement parts. If we choose to replace the Product, we may replace t wth a new or refurbshed Product ofthe same or smlar desgn. We wll retan defectve parts, modules, or equpment. Repar or replacement of the Product, at VTechs opton, s your exclusve remedy.VTech wll return repared or replacement Products to you n workng condton. You should expect the repar or replacement to take approxmately 30 days.
H ln is the limited nt peid?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product underthe terms of this limited warranty, this limited warranty also applies to repaired or replacement Product for a period of either (a) 90 days from the date the repairedor replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
wht is nt cveed b this limited nt?Ths lmted warranty does not cover:
1. Product that has been subjected to msuse, accdent, shppng or other physcal damage, mproper nstallaton, abnormal operaton or handlng, neglect,inundation, re, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modication by anyone other than an authorized service representative of VTech; or
3. Product to the extent that the problem experenced s caused by sgnal condtons, network relablty, or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
wnt
-
8/2/2019 Phone vtech 6042_manual.i2
55/62
.vtechphnes.cm52
5. Product whose warranty/qualty stckers, product seral number plates or electronc seral numbers have been removed, altered or rendered llegble; or
6. Product purchased, used, servced, or shpped for repar from outsde the Unted States of Amerca or Canada, or used for commercal or nsttutonal purposes(including but not limited to Products used for rental purposes); or
7. Product returned without valid proof of purchase (see item 2 below); or
8. Charges for nstallaton or set up, adjustment of customer controls, and nstallaton or repar of systems outsde the unt.
H d u et nt sevice?To obtain warranty service in the United States of America, please call 1 (800) 595-9511; In Canada, please call 1 (800) 267-7377. NOTE: Before calling for service,please review the users manual - a check of the Product controls and features may save you a service call.
Except as provded by applcable law, you assume the rsk of loss or damage durng transt and transportaton and are responsble for delvery or handlng chargesincurred in the transport of the Product(s) to the service location. V Tech will return repaired or replaced Product under this limited warranty to you, transportation,delvery or handlng charges prepad. VTech assumes no rsk for damage or loss of the Product n transt. If the Product falure s not covered by ths lmted warranty,or proof of purchase does not meet the terms of ths lmted warranty, VTech wll notfy you and wll request that you authorze the cost of repar pror to any fur therrepar actvty. You must pay for the cost of repar and return shppng costs for the repar of Products that are not covered by ths lmted warranty.
wht must u etun ith the Pduct t et nt sevice?
1. Return the entire original package and contents including the Pro duct to the VTech service location along wi th a description of the malfunction or difculty; and
2. Include valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
3. Provde your name, complete and correct malng address, and telephone number.
othe Limittins
Ths warranty s the complete and exclusve agreement between you and VTech. It supersedes all other wrtten or oral communcatons related to ths Product.VTech provdes no other warrantes for ths Product. The warranty exclusvely descrbes all of VTechs responsbltes regardng the Product. There are no otherexpress warranties. No one is authorized to make modications to this limited warranty and you should not rely on any such modication.
State/Provincial Law Rights: This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of tness for a particular purpose and merchantability (an unwritten warranty that the Product is t for ordinaryuse) are limited to one year from date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitationmay not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lostprots or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third par ties) resulting from the useof ths Product. Some states/provnces do not allow the excluson or lmtaton of ncdental or consequental damages, so the above lmtaton or excluson maynot apply to you.
Plese etin u iinl sles eceipt s pf f puchse.
FCC, aCTa nd IC eultins
-
8/2/2019 Phone vtech 6042_manual.i2
56/62
.vtechphnes.cm 53
appendix
FCC Pt 15
Ths equpment has been tested and found to comply wth the requrements for a Class B dgtal devce under Part 15 of the Federal Communcatons Commsson
(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, usesand can radate rado frequency energy and, f not nstalled and used n accordance wth the nstructons, may cause harmful nterference to rado communcatons.
However, there s no guarantee that nterference wll not occur n a partcular nstallaton. If ths equpment does cause harmful nterference to rado or televson recep-
ton, whch can be determned by turnng the equpment off and on, the user s encouraged to try to correct the nterference by one or more of the followng measures:Reorent or relocate the recevng antenna.Increase the separaton between the equpment and recever.
Connect the equpment nto an outlet on a crcut dfferent from that to whch the recever s connected.Consult the dealer or an experenced rado/TV techncan for help.
Changes or modications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
To ensure safety of users, the FCC has establshed crtera for the amount of rado frequency energy that can be safely absorbed by a user or bystander accordng tothe ntended usage of the product. Ths product has been tested and found to comply wth the FCC crtera. The handset may be safely held aganst the ear of the user.
The telephone base shall be installed and used such that parts of the users body other than the hands are maintained at a distance of approximately 20 cm (8 inches)or more. If you choose to use a clppng devce, please make sure to only use the suppled VTech belt clp.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2)
Ths devce must accept any nterference receved, ncludng nterference that may cause undesred operaton.Prvacy of communcatons may not be ensured when usng ths telephone.
FCC Pt 68 nd aCTa
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The
label on the back or bottom of this equipment contains, among other things, a product identier in the format US:AAAEQ##TXXXX. This identier must be provided toyour local telephone company upon request.
The plug and jack used to connect ths equpment to premses wrng and the telephone network must comply wth applcable Part 68 rules and techncal requrementsadopted by ACTA. A complant telephone cord and modular plug s provded wth ths product. It s desgned to be connected to a compatble modular jack that s also
compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the users manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called.The REN for this product is encoded as the 6th and 7th characters following the US: in the product identier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas,the sum of all RENs should be ve (5.0) or less. For more information, please contact your local telephone company.
Ths equpment may not be used wth Party Lnes. If you have specally wred alarm dalng equpment connected to your telephone lne, ensure the connecton of ths equp -ment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualied installer.
If ths equpment s malfunctonng, t must be unplugged from the modular jack untl the problem has been corrected. Repars to ths telephone equpment can only
be made by the manufacturer or ts authorzed agents. For repar procedures, follow the nstructons outlned under the Lmted Warranty.
FCC, aCTa nd IC eultins
-
8/2/2019 Phone vtech 6042_manual.i2
57/62
.vtechphnes.cm54
If ths equpment s causng harm to the telephone network, the telephone company may temporarly dscontnue your telephone servce. The telephone company s
required to notify you before interrupting service. If advance notice is not practical, you will be notied as soon as possible. You will be given the opportunity to correctthe problem and the telephone company is required to inform you of your right to le a complaint with the FCC. Your telephone company may make changes in its
facltes, equpment, operaton, or procedures that could affect the proper functonng of ths product. The telephone company s requred to notfy you f such changesare planned.
If ths product s equpped wth a corded or cordless handset, t s hearng ad compatble.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, re, medical) in these locations. If you do store ortest emergency numbers, please:
Remain on the line and briey explain the reason for the call before hanging up.Perform such activities in off-peak hours, such as early morning or late evening.
Indust Cnd
This equipment complies with regulations RSS-213 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The term IC: before the certication/registration number only signies that the Industry Canada technical specications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to
a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all thedevices does not exceed ve.
This Class B digital apparatus complies with Canadian ICES-003.
The RBRC Seal on the nickel-metal-hydride battery indicates that VTech Communications, Inc. is voluntarily participating in an
ndustry program to collect and recycle these batteres at the end of ther useful lves, when taken out of servce wthn the
Unted States and Canada.
The RBRC program provides a convenient alternativ