pneumatic conveying basic points
TRANSCRIPT
Ryan Breese
Product Development Engineer
Lyondell Chemical Company
The Wonderful World of Pneumatic Conveying
It Will Blow You Away…..
DisclaimerThe information in this presentation is, to our knowledge, true and accurate. Equistar makes no representations or warranties as to the completeness or accuracy of the information. All information, suggestions, and recommendations presented by Equistar are without warranty, express or implied, and are not an inducement to use any process, product or design in conflict with any patent. Equistar makes no commitment to update or correct any information.It is the user’s sole responsibility to determine whether, in the user’s particular application, the products and procedures presented here can be safely and satisfactorily used.We may provide web site links and contact information of third parties as a convenience, but this should not be construed as anendorsement by Equistar. Any contacts with such third party areat your own risk. By attending this presentation, the attendee accepts the terms and conditions of this statement.
Goals for Today!
Develop:
General understanding of pneumatic conveying systems and equipment
Understanding of a typical plant’s transfer system
Troubleshooting skills for fines and streamers issues
“We create sustainable business value by being a preferred solutions provider to our customers.”
Agenda
Types of Flow: Dilute vs. Dense Phase
How fines and streamers are generated
System components
System design best practices
What is Pneumatic Conveying?
• Moving objects with air• Vacuum - Pulls
• System pressure is less than atmospheric
• Vacuum Cleaner• Drinking Straw
• Pressure - Push• System pressure is greater than atmospheric
• Leaf Blower• Garden Hose
Dilute vs. Dense Phase…
Stream Flow (Dilute) air/solids > 2.25
Two Phase Flow2.25 < air/solids < 0.2
Pulsed Piston Flowair/solids < 0.2
*loadings ratio in units of scf of air/lbs of pellets
Dilute Phase ConveyingObject are suspended in the conveying air
The transfer velocity is greater than the “saltation” velocity
Low system pressures (< 14 psig)
High air to solids loading ratios (> 2.25)
High linear velocities (4,200 – 6,500 ft/min)
More destructive - mostly due to the high velocities
Lower capital costs at startup
Lower cost equipment / not rated for pressure system
Easier to operate
Wider ∆v range on phase diagram
Dense Phase ConveyingAnything that is not Dilute Phase
The transfer velocity is less than the “saltation” velocity at some point in the system (< 4,200 ft/min)
High system pressures (14 – 90 psig)
Low air to solids loading ratios (< 0.2)
Low velocities but high pounds capacity (101 – 102 ft/min)
Less destructive – a result of lower velocity
Higher capital costs at startup
Pressure rated lines, airlocks, valves, etc.
More difficult to operate (easier to plug)
Narrower ∆v range on phase diagram
Pneumatic Conveying Phase Diagram
The Origin of Fines and Streamers
A coating of plastic formed by smearing pellets against the pipe wall
Skin peels off in strips and becomes streamers, angel hair, and/or fines
Pellet Tail Can Form FinesTails are small stubs of polymer that are the result of poor pellet cut
Pellet tails can break off and generate fines
Small percentage of fines studied looked like pellet tails (<7%)
Fines Are “Mini-Streamers”Most fines look like “mini-streamers” under a microscope
Most fines are generated by “smearing” and not tails.
Breaking up of snakeskins forms angel hair and fines
Typical Conveying System
Feed VesselFeed Point
Pressure System: Air Lock (rotary valve)Vacuum System: Gate Valve
Air Mover (Blower)Pressure: Mover at the solids pickupVacuum: Mover at discharge vessel
Air CoolerLocated at the blower dischargeEspecially a concern with pressure systems due to temperature rise induced by the blower
Typical Conveying System-ContinuedTransfer line
including piping, elbows, and divert valves
Discharge vessel
Feed hopper at the extruder
Particulate removal equipmentBag filters (suction of vacuum blowers)
Dedusters-fines
Elutriators-some fines and streamers
Scalperators-streamers
Cyclones
tangential entry vessels can be conducive to streamers generation
Typical Pellet Transfer System
StorageSilos Elutriator
Deduster
Scalperator
Blower/Cooler
The Common Elbow
Long Radius Bends
Lowest −∆P
among all bends~20 ft of straight pipe
Generates StreamersPellets “smear” against the outermost wall of the elbow
Frictional heat generated by this rubbing causes the outer portion of the pellet to melt and leave a skin
This skin peels off as snakeskins and could potentially be broken into angel hair/fines
Dead End TeesLargest −∆P among all bends
~70 ft. of straight pipe
Minimizes streamers
Semi-static bed of pellets forms in dead end and acts as a cushion
Vortex in bed provides for self cleaning
Tee wears out if pocket is not formed due to low solids/air ratio
Least expensive of specialty bends
Easy to fabricate
Hammertek Smart Elbow
−∆P similar to long radius
Minimizes wear
Minimizes streamersCirculating bulb of pellets deflects the solids
Specialty Elbows
Coperion Gamma Bend
−∆P is less than DET but greater than LR
Minimizes streamersMoving bed of pellets minimizes impact
Specialty ElbowsDiamond Cut
−∆P similar to short radiusgreater than long radius bends
similar/slightly less than DET
Minimizes streamers
Streamers prevented from Diamond Cut on inner wall
Fines generation is still an issue-smearing mechanism of pellets to metal is still present
Specialty Piping
Shot Peened
Shot is used to roughen the inside of the transfer pipe
The roughening of the pipe prevents the formation of snakeskins
More fines are generated due to abrasion
Helps with reducing large snakeskins but generates more fines
Inexpensive initial cost, but has a short life span
Specialty Piping
Spiral Grooved
A lip is machined into the inner wall of the pipe
Groove acts as a “speed bump” and prevents the pellets from smearing
Expensive initial cost
Has a substantially longer lifespan than peening
Ideal Pneumatic Conveying Conditions For Pellet Conveying
Some Heuristics…
VelocitiesPickup = 4,200 ft/min for pressure
= 4,400 ft/min for vacuumTerminal (exit) should be less than 6,000 ft/min
TemperatureAs cold as possible!
Temperatures above 100 °F are excessive
Designing Line LayoutAvoid inclined lines
Keep lines horizontal and verticalAvoid installing elbows within close distances to each other
Have straight stretch between elbowsAvoid bends and use direct pathsAvoid bends within 20-30 pipe diameters from the pickup pointNever use more than 2 bends in a seriesDownward conveying design
Treat as horizontal when doing pressure calculations
Designs Which Cause Line Plugs
Line configurationsAvoid bends at the pickup
First bend at ~ 20-30 pipe diameters
Minimize the changes in directionDo not use upward sloping lines
Conveying air conditionsIf a loss of air volume occurs, check…
Blower: dirty filters, leakage through rotary feeders, valves, couplings, holes, non-seating RV, opening of RV due to over pressuring
Dirty filter on resin vessel
Designs Which Cause Line PlugsMiscellaneous
Resin vesselImproperly sized feeder
bridging in cone
Material buildup in lineresult of fine materials and moisture
Additives, etc.
A line plug will typically be found about 40’ downstream of a leak!!!
Ways To Increase CapacityMinimize flex hose length and eliminate where possibleIncrease pressure to system’s maximum by optimizing solids/air ratioCheck sloping lines for recycling of materialMinimize the number of bendsShorten the total conveying distanceIncrease/decrease the system’s air supply
Install a larger/smaller blower, change rpm, etcMust take into consideration pressure limitations
Step up the line diameter near the end of the systemDoing so decreases the total system pressure
Ways To Minimize Wear in Conveying Lines
Wear:
Reduce conveying velocities
Use wear resistant materialsMore prevalent for abrasive materials
Sand, carbon black, etc.
Minimize line length and number of bendsLower velocities and fewer changes in direction
( ) 4−∝ velocitylinearFailuretoTime
Ways To Minimize Wear in Vessels
Enter the vessel radially, not tangentially
Hang a flapper in the middle of the bin to allow the material to contact it instead of the vessel wall
Step up the line diameter 40’ before the vessel entrance to reduce conveying velocities
Top 5 Reasons for Fines/Streamers Issues…1. High transfer velocities
2. High conveying temperatures
No cooler on pressure system
3. Long Radius Bends in service
Especially near the end of a conveying system
4. No fines/streamers removal device
Bag filter on vacuum suction
5. No preventative maintenance for silo washing
Rinse out silos at least semi-annually
ResourcesTransfer System Engineering Companies
MACHammertekFuller Bulk HandlingCoperion Waeschle
ConsultantsPneumatic conveying consultants: Paul Solt
http://www.powderandbulk.com/pcc/index.htmlPhone: (610) 437-3220 ([email protected])
PSRI (Particulate Solid Research, Inc.): Ted Knowltonhttp://psrichicago.com/Phone: (773) 523-7227 ([email protected])
www.powderandbulk.com“Pneumatics Points to Ponder” Articles by Paul Solt