pontoon bench seating must have railing or support to ... · pdf filewarning! pontoon bench...
TRANSCRIPT
WARNING!
Pontoon Bench Seating must have railing or
support to place back against for installation.
DO NOT USE AS FREE STANDING SEAT
PLASTIC CORNER GUARDS ARE FOR SHIPPING PURPOSES ONLYTHEY CAN BE REMOVED
WF1123
THE WISE COMPANYMANUFACTURERS OF QUALITY MARINE SEATING SINCE 1960
472 WEST 9TH ST., RECTOR, AR 72461 • TOLL FREE TEL: 1.800.759.5769 • www.wiseseats.com
PONTOON FURNITURE ASSEMBLY INSTRUCTIONS
Hardware Package: 1” Base screws, 4” threaded posts, fender washers, lock washers and wing nuts.Tools Required: Matching pattern Phillips head hand or power screwdriver. Pliers.
NOTE: USE PLIERS TO REMOVE PLASTIC CORNER GUARDS INCLUDING ANY PROTRUDING STAPLES
All 27”, 36”, 45”, 50” Straight Benches & all 45” Corner Couches
Assembling Seat Bottom Cushion to Plastic Base1. Remove the hinge from the seat cushion bottom by removing the screws.
Take note of the hinge placement for correct re-placement of hinge on the base and bottom.
2. Place the hinge onto the seat base and insert the 1” base screws in the3 pre-drilled holes in the seat base. Screw down but do not tighten yet.
3. Turn the seat base so that the front of the base is facing down.4. Place the seat bottom next to the base to re-attach the 3 screws removed
from the hinge in step one. Start screws by hand only. Once started,screw down but again do not tighten.
5. First tighten the 3 base hinge screws into the base. Second, tightenthe screws in the seat bottom cushion.Important to tighten in this order!
All 27”, 36”, 45”, 50” Straight Benches, All 25” - 32” Seats & All 45” Corner Couches
Assembling Seat Back to Base1: Locate threaded inserts in the bottom of the seat back. 27” & 36” Bench
have 2 inserts, 45” bench 3 inserts, 50” bench 4 inserts, 45” corner couch 4 inserts, 25” & 32 “ corners 4 inserts.
2: Hand Screw 4” threaded posts in inserts about half way or until they stop.3: Place back into recessed channel in seat base. Posts must protrude base
openings to secure.4: Place in order fender washer, lock washer, wing nut onto post and tighten securely.
Standard & 72 Quart Cooler Flip-Flop Assembly1: Follow instructions from Bench assembly to attach hinge to
seat base and seat bottom cushion.2: Remove the four, 1” screws from back cushion. Look on both
sides for 2 openings in the vinyl.3: Screw support bars into back cushion using the 4 screws removed
from back cushion. Hand start to protect insert threads. Then tighten securely.
4: Attach support bar to bottom of base using the 2 screws providedin hardware pack. Hand start and then tighten securely.
Steering Console1: Remove the 4 screws in the front access panel to access inside
of console. Consult your marine professional to install gauges, steering wheel, cables, throttle box, and electrical wiring.
To install furniture onto your pontoon consult your marine professional for removal of current furniture and installation of new furniture.
Missing Hardware or Questions?Call 1-800-759-5769 • Rector, AR • Monday-Friday 8 am to 4 pm Central time
Base
Studs
Back
Seat Cushion
Hinge Screws
Mounting Screws
Access Panel
Captain's Helm
THE WISE COMPANYWF1155
MANUFACTURERS OF QUALITY MARINE SEATING SINCE 1960462 WEST 9TH ST., RECTOR, AR 72461 • TOLL FREE TEL: 1.800.759.5769 • www.wiseseats.com
55” BENCH SEAT ASSEMBLY INSTRUCTIONS
QUALITY PREMIUM & DESIGNER PLASTIC PONTOON SEATING
• The only tools needed are a pair of pliers and a Phillips screwdriver.
• Seat cushion must be attached to the front of the base. Flip up to install backrest, (see illustration below).
• The backrest will slide directly into the recess located at the back of the base.
• To permanently attach backrest, screw the 1/4"x 2" studs into back. Push back through holes in base. Put washers and wing nuts on studs and tighten.
PACKAGE CONTENTSThree cartons containing a seat andbackrest cushion set and two bases.
Above items are not manufactured for commercial use.
Questions? Missing Parts?Call 1.800.759.5769
THE WISE COMPANYMANUFACTURERS OF QUALITY MARINE SEATING SINCE 1960
472 WEST 9TH ST., RECTOR, AR 72461 • TOLL FREE TEL: 1.800.759.5769 • www.wiseseats.com
• The only tools needed are a pair of pliers and a Phillips screwdriver.
• Seat cushion must be attached to the front of the base. Flip up to install backrest.
• The backrest will slide directly into the recess located at the back of the base.
• To permanently attach backrest, screw the 1/4"x 2" studs into back. Push back through holes in base. Put washers and wing nuts on studs and tighten.
PACKAGE CONTENTSTwo cartons containing a seat cushion, base, backrest and hardware.
PACKAGE CONTENTSBack cushion, seat cushion, baseand hardware.
PONTOON ASSEMBLY INSTRUCTIONS27"- 36"- 45"- 50" Bench & Corner Section
Flip-Flop Seat
• Attach uprights and washer using 1-1/2" screw, tighten securely.
Attach Swing Arm Assembly to Base
• Using 1-1/2" screws, mount back to uprights, tighten assembly.
Use seat cushion instructions above for flip flop seat.
Attach Swing Arm Assembly to Back
Above items are not manufactured for commercial use.
Questions? Missing Parts?Call 1.800.759.5769
DO NOT USE AS FREE STANDING SEATPontoon Bench Seating must have railing or support to place back against for installation
IMPORTANT
WF 1133
NOTETO AVOID CROSS-THREADING OF FASTENERS PLEASE START
ALL SCREWS BY HAND
3.25.07
THE WISE COMPANYMANUFACTURERS OF QUALITY MARINE SEATING SINCE 1960
472 WEST 9TH ST., RECTOR, AR 72461 • TOLL FREE TEL: 1.800.759.5769 • www.wiseseats.com
Above items are not manufactured for commercial use.
Questions? Missing Parts?Call 1.800.759.5769
STEERING CONSOLEASSEMBLY INSTRUCTIONS
PACKAGE CONTENTS
1. Remove 4 oval head mounting screws and countersunk washers.
2. Remove cover panel.
To Remove Access Cover Panel
1. Reverse instructions above to mount panel and tighten fasteners by hand. Do not over tighten or screws will strip out plastic.
To Mount Access Panel
• When mounting steering wheel assembly and throttle control, trim only vinyl necessary to clear component through hole.
• Adequate upholstery material for steering column bezel and throttle cover plate must remain for plate to securely overlap and capture vinyl.
• Follow manufacturers specific directions for installation of steering assembly and throttle control.
• When mounting throttle directly to helm please consult your local marine professional.
NOTE
Helm with mounted upholstered access cover panel.
Mounting Screws
Access Panel
Captain's Helm
WF 1132
NOTETO AVOID CROSS-THREADING OF FASTENERS PLEASE START
ALL SCREWS BY HAND
3.25.07
STAPLES MAY PROTRUDE THROUGH PLASTIC SHELL
BE CAREFUL TO AVOID BEING CUT
WARNING
PACKAGE CONTENTS
Back cushion, seat cushion, base and hardware
WD437SSLIVEWELL COOLER SEAT
WF1147
NOTETO AVOID CROSS-THREADING OF FASTENERS PLEASE START
ALL SCREWS BY HAND
SWINGBACK COOLER/LIVEWELLASSEMBLY INSTRUCTIONS
Above items are not manufactured for commercial use.
Questions? Missing Parts?Please contact store fromwhich it was purchased
• Attach uprights and washer using 1-1/2" screw, tighten securely.
Attach Swing Arm Assembly to Base
• Using 1-1/2" screws and 5/8" washer mount back to uprights, tighten assembly.
Attach Swing Arm Assembly to Back
PACKAGE CONTENTS
Back cushion, seat cushion, base and hardware
WD15670 QUARTSWINGBACK COOLER SEAT
WD15950 QUARTSWINGBACK COOLER SEAT
• Attach uprights and washer using 1-1/2" screw, tighten securely.
Attach Swing Arm Assembly to Base
• Using 1-1/2" screws, mount back to uprights, tighten assembly.
Attach Swing Arm Assembly to Back
1/4" x 1-1/2"
1/4" x 1-1/2"
1/4" x 1-1/2"
Washer
Washer
1/4" x 1-1/2"