GB

Valid for serial no. 538--xxx--xxxx0443 934 201 GB 061219

PRC 17-49PRC 33-90PRC 60-170A21

Instruction manual

-- 2 --TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 INTRODUCTION 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 TECHNICAL DATA 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 INSTALLATION 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Connection 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.2 Assembly instructions 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 OPERATION 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.1 Securing the welding tool for welding 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.2 Adjustments 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.3 Welding in confined spaces 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 MAINTENANCE 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.1 Daily 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.2 As necessary 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.3 Replacing wear parts 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.4 Fitting of tungsten electrode 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.5 Dismounting the tongs from the tool 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 ORDERING OF SPARE PARTS 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ORDERING NUMBER 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WEAR PARTS 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ACCESSORIES 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

-- 3 --dsa9d1ea

1 DIRECTIVEDECLARATION OF CONFORMITY

ESAB AB Welding Equipment, 695 81 Laxå, Sweden, declares that tube welding tool PRC 17--49 /33--90 / 60--170 from serial number 538 onwards, conforms to standard IEC/EN 60204--1/ IEC/EN12100--2 in accordance with the requirements of directive (98/37/EEC) and standard IEC/EN60974--10 in accordance with the requirements of directive (89/336/EEC).----------------------------------------------------------------------------------------------------------------------------------

Kent EimbrodtGlobal Director Equipment and AutomationESAB AB695 81 LAXÅSWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924

Laxå 2006--12--15

2 SAFETYUsers of ESAB welding equipment have the ultimate responsibility for ensuring that anyone whoworks on or near the equipment observes all the relevant safety precautions. Safety precautionsmust meet the requirements that apply to this type of welding equipment. The following recommen-dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the weldingequipment. Incorrect operation of the equipment may lead to hazardous situations which can resultin injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:S its operationS location of emergency stopsS its functionS relevant safety precautionsS welding

2. The operator must ensure that:S no unauthorized person is stationed within the working area of the equipment when it is

started up.S no--one is unprotected when the arc is struck

3. The workplace must:S be suitable for the purposeS be free from drafts

4. Personal safety equipmentS Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautionsS Make sure the return cable is connected securely.S Work on high voltage equipment may only be carried out by a qualified electrician.S Appropriate fire extinquishing equipment must be clearly marked and close at hand.S Lubrication and maintenance must not be carried out on the equipment during operation.

ESAB can provide you with all necessary welding protection and accessories.

This product is solely intended for arc welding.

GB

-- 4 --dsa9d1ea

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BEBASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can killS Install and earth the welding unit in accordance with applicable standards.S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.S Insulate yourself from earth and the workpiece.S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to healthS Keep your head out of the fumes.S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.S Protect bystanders with suitable screens or curtains.

FIRE HAZARDS Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearingS Protect your ears. Use earmuffs or other hearing protection.S Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

WARNING!Read and understand the instruction manual before installingor operating.

Do not dispose of electrical equipment together with normal waste!In observance of European Directive 2002/96/EC on Waste Electrical and ElectronicEquipment and its implementation in accordance with national law, electrical equipmentthat has reached the end of its life must be collected separately and returned to anenvironmentally compatible recycling facility. As the owner of the equipment, you shouldget information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

3 INTRODUCTION

PRC 17--49 / 33--90 / 60--170 is designed for TIG welding of tube joints.

The tube welding tools are water--cooled and include weaving function (6) andautomatic arc length control (by control of the arc voltage = AVC) (5). The tools areadapted for connection to the power source MechTig. When filler wire is required theMEI 21 wire feed unit is to be used.

GB

-- 5 --dsa9d1ea

The tube welding tools incorporate a special gripping principle facilitating rapid andaccurate securing and location of the tool on the tube.The pair of gripping jaws (4) clamp thetool to the tube when the locking lever(1) on the handle is pressed in. Only thegear collar (3) with the fitted detailsrotates during welding.

The collar is powered by a drive unit (2)consisting of a perm. magnet DC motorand a pulse transmitter for speedcontrol. The motor is powered by thecontrol equipment (power source).

4 TECHNICAL DATA

Tube welding tool PRC 17--49 PRC 33--90 PRC 60--170

Max welding current at 100% duty cycle (A) 250 250 250

Tube, external diameter (mm) 17--49 33--90 60--170

Rotary speed (r.p.m.) 0.12 -- 2.4 0.08 -- 1.6 0.05 -- 0.95

Weight without cable, hose package, AVC-- andweaving--unit (kg)

2.8 3.2 4.4

Length of hose bundle (m) 7 7 7

Tungsten electrode, diameter (mm) 1.6 / 2.4 1.6 / 2.4 1.6 / 2.4

Filler wire, diameter (mm) Fe, SS 0.6 / 0.8 / 0.9 0.6 / 0.8 / 0.9 0.6 / 0.8 / 0.9

Drive unitMax armature voltage (V DC)Max armature current (A DC)

Armature speed at 20 volt (r.p.m.)Mechanical gear ratio

240,56950246:1

240,56950246:1

240,56950246:1

WeavingMotor

Max armature voltage (V DC)Max armature current (A DC)

Max speed, weaving motion (mm/s)Min speed, weaving motion (mm/s)Setting range (mm)Amplitude (mm)Weight (kg)

240.21222061.8

240.21222061.8

240.21222062.2

AVC (Arc Voltage Control)Motor

Max armature voltage (V DC)Max armature current (mA DC)

Normal control speed at 10 V (arc control, mm/s)Weight (kg)

120.220.5

120.220.5

120.220.5

GB

-- 6 --dsa9d1ea

5 INSTALLATION

The installation must be executed by a professional.

WARNING!

Rotating parts can cause injury, take great care.

WARNING!This product is intended for industrial use. In a domestic environment this product may cause radiointerference. It is the user’s responsibility to take adequate precautions.

5.1 Connection

A Motor cable -- rotation

B Wire conduit

C Cooling-- water hose out

D Cooling-- water hose in

E Welding cable

F Gas hose

G Motor cable -- Weaving unit

H Measurement cable -- AVC--unit

I Motor cable -- AVC--unit

GB

-- 7 --dsa9d1ea

5.2 Assembly instructions

AVC unit

Weaving unit

Weaving unit (3) and the tongs (1) can alsobe fitted reversed to the tool, i.e. the lockinglever (1c) downwards.

S Dismounting the tongs (1) and weavingunit (3) from the rotary unit (4).

A special fixture (5) is supplied which isto be fitted between the gripping jaws(1b) and the gear collar (4b) beforetightening. This is to avoid centredisplacement when fixing the tongs (1)to the rotary unit (4).

6 OPERATION

General safety regulations for the handling of the equipment can be found onpage 3. Read through before you start using the equipment!

To avoid the welding tool being damaged, check that the return cable is connected to theworkpiece and that the tungsten electrode is in the start position before the welding commences.

WARNING!

GB

-- 8 --dsa9d1ea

6.1 Securing the welding tool for welding

S Set the correct tube diameter using the adjusting screw (3), keeping thelocking lever (1) in the closed position.

S Open the welding tool bymeans of the locking lever (1).

S For correct preclamping, turn anotherquarter of a turn using adjusting screw (3).N.B. Harder clamping can deform the tongsleading to centre displacement and welddefects.

For welding using equipment for tube diameters 8--17mm (see accessories, page 18) the welding tool is to befixed with the drive unit in vertical position, as analternative a support or relief could be placed under thedrive unit to prevent the welding tool turning round thetube.

S Close the welding tool again by means of the locking lever (1).

S Disengage the gear collar by way of the disengagement arm (2).

S Turn the gear collar (4) about 1.5 turns so as to wind up the connection cable.

6.2 Adjustments

Adjusting the position of the tungsten electrode in the weld joint

S Adjust the electrode distanceradially using the control box withAVC--unit (3).

N.B. When using the tool for the max. tubediameters 49, 90, 170 mm, the distancebetween the periphery of the tube and the gascup cannot exceed 7.5 mm.

S Adjust the position of the wire axially with settingscrew (1) or over the programming box withweaving unit (2).

The spring load of the arm of the electrode holder ispreset on delivery. If adjustment is necessary, pleasecontact your nearest ESAB representative forinformation.

Inserting the filler wire

S See instruction manual for wire feedunit.

Adjusting the filler wire

S Adjust the filler wire nozzle (1)radially by way of an Allen key. Forfine adjustment use the wheel (2).

GB

-- 9 --dsa9d1ea

6.3 Welding in confined spaces

PRC 17--49 with AVC

PRC 17--49 with AVC and weaving unit

PRC 17--49 D C--C min

S Complete. D±49 70+D

S Without wheel (1) for precise wire adjustment.S The torch cover (3) may need to be replaced by shortervariants.

D±49 70+D/2

S Without wheel (1) for precise wire adjustment.S Without end plates (2).S With room for cables in axial direction.S The torch cover (3) may need to be replaced by shortervariants.

S With filler wire nozzle 0443 880 880.

D±3434±D±49

56+ D/239+D

GB

-- 10 --dsa9d1ea

PRC 33--90 with AVC

PRC 33--90 with AVC and weaving unit

PRC 33--90 D C--C min

S Complete. D±6868±D±90

94+D/260+D

S Without wheel (1) for precise wire adjustment.S The torch cover (3) may need to be replaced by shortervariants.

D±90 94+D/2

S Without wheel (1) for precise wire adjustment.S Without end plates (2).S With room for cables in axial direction.S The torch cover (3) may need to be replaced by shortervariants.

D±90 82+D/2

GB

-- 11 --dsa9d1ea

PRC 60--170 with AVC

PRC 60--170 with AVC and weaving unit

PRC 60 -- 170 D C--C min

S Complete. D±170 137+D/2

GB

-- 12 --dsa9d1ea

7 MAINTENANCE

Regular maintenance is important for safe, reliable operation.

Note!All guarantee undertakings from the supplier cease to apply if the customer himselfattempts any work in the product during the guarantee period in order to rectify anyfaults.

7.1 Daily

Make sure that all cables and hoses are undamaged.

7.2 As necessary

Clean and grease all sliding surfaces using fresh grease, see accessories, page 18.

Changing the complete electrode holder

S Open the protective cover (1).

S Disassemble the connection blocks (2) and (3) by removing the Allen screws.

S Dismount the clamp (6).

S Withdraw the old electrode holder (5) through the protecting cover (1). Send ittogether with clamp (6) to your nearest ESAB representative for exchangeaccording to our exchange system.

S Fit the new electrode holder in reverse order.

S Make sure the o--rings are properly fitted between the connection blocks (2) and(3).

GB

-- 13 --dsa9d1ea

Repair of multi--conductor

NOTE! This should be done by authorised ESAB service people.

S Loosen the clamps (4), (6) at the damaged end and withdraw the hose (7).

S Unsolder the current nipples (11) from the electrode holder (12) / connectionblock (2).

S Cut off the damaged part of the hose, but leave a couple of extra centimetres ofthe current litzes.

S Fit a tape (8) round the current litzes (9) in level with the hose end to mark thelength of the hose.

S Draw the current litzes (9) some 60--70 mm out of the hose and prevent thelitzes slipping back, using a safety pin or a metal wire (10).

S Cut the litzes (9) about 15 mm shorter than the hose.

S Fit new current nipples (11) using a pair of cable pliers or other suitable device.

S Solder the current nipples (11) against the electrode holder (12) / connectionblock (2) using tin solder.

S Remove the safety pin/metal wire (10).

S Wet the current nipples (11) and push over the hose (7).

S Put back the clamps (4) and (6).

GB

-- 14 --dsa9d1ea

7.3 Replacing wear parts

S Remove the torch cover (1).

S Remove the tungsten electrode (5).

S Remove the clamping sleeve (2).

S Remove the gas cup (6).

S Unscrew the electrode nozzle (4) from the gaslens (3) by means of an Allen key.

S Fit the parts in the reverse orderNote: Make sure the gas lens (3) is fitted with thesmooth side against the sealing washer (7).

7.4 Fitting of tungsten electrode

File off the tungsten electrode and fit it into the electrode holder as follows:

S Remove the torch cover (1).

S Insert the tungsten electrode (5) into the electrode nozzle (4) and clampingsleeve.

S Clamp the tungsten electrode with the torch cover (1).

7.5 Dismounting the tongs from the tool

See “Weaving unit” on page 7.

8 ORDERING OF SPARE PARTS

PRC 17--49 / 33--90 / 60--170 is designed and tested in accordance with the internationaland European standards IEC/EN 60204--1 / 12100--2 and EN 60974--10. It is the obliga-tion of the service unit which has carried out the service or repair work to make surethat the product still conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page ofthis publication.

GB

PRC 14-49, PRC 33-90, PRC 60-170

Edition 061219

Ordering number

-- 15 --dsa9o

Ordering no. Denomination Type Notes

0443 751 881 Tube welding tool PRC 17--49 AVC, Water cooled

0443 752 881 Tube welding tool PRC 17--49 AVC, weaving unit, water cooled

0443 761 881 Tube welding tool PRC 33--90 AVC, Water cooled

0443 762 881 Tube welding tool PRC 33--90 AVC, weaving unit, water cooled

0443 771 881 Tube welding tool PRC 60--170 AVC, Water cooled

0443 772 881 Tube welding tool PRC 60--170 AVC, weaving unit, water cooled

0443 934 990 Spare parts list PRC 17--49, PRC33--90, PRC 60--170

Instruction manuals and the spare parts list are available on the Internet at www.esab.com

PRC 14-49, PRC 33-90, PRC 60-170

R0443 934/E061219/P20

Wear parts

-- 16 --dsa8w

Itemno.

Qty Ordering no. Denomination Notes

0443807880 Wear parts

1 0332811001 Clamping sleeve 1,6

2 0332811003 Clamping sleeve 2,4

3 0443785001 Electrode nozzle 1,6

4 0443785002 Electrode nozzle 2,4

5 0151574002 Tungsten electrode 1,6

6 0151574003 Tungsten electrode 2,4

7 0443787001 Sealing washer

8 0443786001 Gas lens

9 0332801880 Torch cover

10 0365310049 Torch cover

11 0365310050 Torch cover medium

12 0443788001 Gas cup

13 0333420880 Journal

14 0443813001 Ball pressure screw

PRC 14-49, PRC 33-90, PRC 60-170

R0443 934/E061219/P20-- 17 --dsa8w

Itemno.

Qty Ordering no. Denomination Notes

0443815880 Wire setting parts

1 1 0443789001 Wire attachment

2 1 0443790001 Wire rock

3 1 0443791001 Wire knob 44 mm

1 0443791002 Wire knob 62 mm

1 0443791003 Wire knob 72 mm

4 1 0443792001 Spring

5 1 0192238219 Screw IN6 M3 x 5, DIN 912

6 1 0212204343 Screw M5 x 6

7 2 0190509321 Screw M5 x 6

8 1 0332792001 Joural

PRC 14-49, PRC 33-90, PRC 60-170

Edition 061219

Accessories

-- 18 --dsa9a

Angular support 0443 875 880. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PRC 17--49 wire conduit for welding in confined spaces 0443 880 880. . . . . . . . . . . . . . . . . . . . . . .Wheel for precise wire adjustment (62 mm) PRC 17--49, 33--90 0443 791 002. . . . . . . . . . . . . . . .Conversion kit for PRC 17--49 welding of tube diameters 8--17 mm 0444 002 880. . . . . . . . . . . . . .Conversion kit for PRC 33--90 welding of tube diameters 20--33 mm. 0443 908 880. . . . . . . . . . . .Conversion kit for PRC 60--170 welding of tube diameters 44--60 mm. 0443 909 880. . . . . . . . . . .Driving unit 134:1 0443 544 880. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Plate for angular support together with conversion kit for smaller diameters 0444 226 880. . . . . .Wire holder complete with gas lens Ø24 mm with adjustable wire nozzle forPRC 33--170 0443 923 880. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wire nozzle straight for PRC 17--170 complete adjustable holder 0443 988 880. . . . . . . . . . . . . . .

-- 19 --p

ESAB ABSE--695 81 LAXÅSWEDENPhone +46 584 81 000

www.esab.com

061127

ESAB subsidiaries and representative offices

EuropeAUSTRIAESAB Ges.m.b.HVienna--LiesingTel: +43 1 888 25 11Fax: +43 1 888 25 11 85

BELGIUMS.A. ESAB N.V.BrusselsTel: +32 2 745 11 00Fax: +32 2 745 11 28

THE CZECH REPUBLICESAB VAMBERK s.r.o.VamberkTel: +420 2 819 40 885Fax: +420 2 819 40 120

DENMARKAktieselskabet ESABHerlevTel: +45 36 30 01 11Fax: +45 36 30 40 03

FINLANDESAB OyHelsinkiTel: +358 9 547 761Fax: +358 9 547 77 71

FRANCEESAB France S.A.Cergy PontoiseTel: +33 1 30 75 55 00Fax: +33 1 30 75 55 24

GERMANYESAB GmbHSolingenTel: +49 212 298 0Fax: +49 212 298 218

GREAT BRITAINESAB Group (UK) LtdWaltham CrossTel: +44 1992 76 85 15Fax: +44 1992 71 58 03

ESAB Automation LtdAndoverTel: +44 1264 33 22 33Fax: +44 1264 33 20 74

HUNGARYESAB KftBudapestTel: +36 1 20 44 182Fax: +36 1 20 44 186

ITALYESAB Saldatura S.p.A.Mesero (Mi)Tel: +39 02 97 96 81Fax: +39 02 97 28 91 81

THE NETHERLANDSESAB Nederland B.V.UtrechtTel: +31 30 2485 377Fax: +31 30 2485 260

NORWAYAS ESABLarvikTel: +47 33 12 10 00Fax: +47 33 11 52 03

POLANDESAB Sp.zo.o.KatowiceTel: +48 32 351 11 00Fax: +48 32 351 11 20

PORTUGALESAB LdaLisbonTel: +351 8 310 960Fax: +351 1 859 1277

SLOVAKIAESAB Slovakia s.r.o.BratislavaTel: +421 7 44 88 24 26Fax: +421 7 44 88 87 41

SPAINESAB Ibérica S.A.Alcalá de Henares (MADRID)Tel: +34 91 878 3600Fax: +34 91 802 3461

SWEDENESAB Sverige ABGothenburgTel: +46 31 50 95 00Fax: +46 31 50 92 22

ESAB international ABGothenburgTel: +46 31 50 90 00Fax: +46 31 50 93 60

SWITZERLANDESAB AGDietikonTel: +41 1 741 25 25Fax: +41 1 740 30 55

North and South AmericaARGENTINACONARCOBuenos AiresTel: +54 11 4 753 4039Fax: +54 11 4 753 6313

BRAZILESAB S.A.Contagem--MGTel: +55 31 2191 4333Fax: +55 31 2191 4440

CANADAESAB Group Canada Inc.Missisauga, OntarioTel: +1 905 670 02 20Fax: +1 905 670 48 79

MEXICOESAB Mexico S.A.MonterreyTel: +52 8 350 5959Fax: +52 8 350 7554

USAESAB Welding & Cutting ProductsFlorence, SCTel: +1 843 669 44 11Fax: +1 843 664 57 48

Asia/PacificCHINAShanghai ESAB A/PShanghaiTel: +86 21 5308 9922Fax: +86 21 6566 6622

INDIAESAB India LtdCalcuttaTel: +91 33 478 45 17Fax: +91 33 468 18 80

INDONESIAP.T. ESABindo PratamaJakartaTel: +62 21 460 0188Fax: +62 21 461 2929

JAPANESAB JapanTokyoTel: +81 3 5296 7371Fax: +81 3 5296 8080

MALAYSIAESAB (Malaysia) Snd BhdSelangorTel: +60 3 8027 9869Fax: +60 3 8027 4754

SINGAPOREESAB Asia/Pacific Pte LtdSingaporeTel: +65 6861 43 22Fax: +65 6861 31 95

SOUTH KOREAESAB SeAH CorporationKyungnamTel: +82 55 269 8170Fax: +82 55 289 8864

UNITED ARAB EMIRATESESAB Middle East FZEDubaiTel: +971 4 887 21 11Fax: +971 4 887 22 63

Representative officesBULGARIAESAB Representative OfficeSofiaTel/Fax: +359 2 974 42 88

EGYPTESAB EgyptDokki--CairoTel: +20 2 390 96 69Fax: +20 2 393 32 13

ROMANIAESAB Representative OfficeBucharestTel/Fax: +40 1 322 36 74

RUSSIALLC ESABMoscowTel: +7 095 543 9281Fax: +7 095 543 9280

LLC ESABSt PetersburgTel: +7 812 336 7080Fax: +7 812 336 7060

DistributorsFor addresses and phonenumbers to our distributors inother countries, please visit ourhome page

www.esab.com