pro-xl h2o water-based paint - try it !

Automotive Waterbased Basecoat System

Over 50,000 up-to-date colours available

THE NEW WORLD OF WATERBASED COATINGS! ProXL H2O Waterbased basecoat system provides the vehicle refinisher with not only fully compliant coatings, but a cost effective, material saving paint system. When economic advantages are required, ProXL H2O fully meets these demands due to its high transfer efficiency, its covering capacity and outstanding drying times.

7 KEY SYSTEM FEATURES

1) AMAZING PERFORMANCE! ProXL H2O gives outstanding coverage in 1 coat, reducing material consumption and wastage - see the comparison test opposite.

2) SUPER EFFICIENT! ProXL H2O provides fast easy application and drying times without the addition of additives or activators.

3) SIMPLE TO USE! ProXL H2O is simple to use and provides quality results.

4) HIGH QUALITY! ProXL H2O is highly suitable for all vehicle repairs however small or large.

5) FANTASTIC COLOUR MATCH! ProXL H2O offers over 50,000 professional colours available from up-to-date colour software system. Each colour is represented as a sprayed out chip in a comprehensive colour box.

6) TOTALLY FLEXIBLE! ProXL H2O can be finished using any of the branded ProXL products.

7) FULLY COMPLIANT! ProXL H2O is fully compliant with 2005/42/CE European VOC emissions legislation.

ProXL H2O - Waterbased

Automotive Basecoat

FEATURE ADVANTAGE BENEFIT Colour formulation software

Faster mixing of colour formula

Time and cost savings

Easier application Less effort Less risk of error

No extensive training needed Material, time and cost savings

Improved coverage Less material usage Faster application

Shorter repair time Material, time and cost savings

Excellent metallic control Less risk of mottling Time and cost saving

Easier spot repair Less risk of halos or contour mapping

Time and cost saving

Less aggressive Easier 2nd repair less risk for lifting

Time and cost saving

Wider application window Easy application No extra training required Time and cost saving

State of the art pigments used

Better colour accuracy Less colour problems

Material, time and cost savings

t: +44 (0)1634 823900 e: [email protected]

www.capellasolutionsgroup.com

CODE DESCRIPTION SIZE W000 ProXL H20 - CLEAR 500ML

W020 ProXL H20 - WHITE 1LT

W100 ProXL H20 - SHADOW WHITE 500ML

W110 ProXL H20 - LUMINOUS BLUE 1LT

W130 ProXL H20 - PURE BLUE 1LT

W160 ProXL H20 - BRILLIANT BLUE 1LT

W180 ProXL H20 - REDDISH BLUE 1LT

W210 ProXL H20 - LUMINOUS GREEN 1LT

W240 ProXL H20 - GOLDEN GREEN 1LT

W330 ProXL H20 - MEDIUM YELLOW 500ML

W340 ProXL H20 - TRANSPARENT YELLOW 500ML

W350 ProXL H20 - OXYDE YELLOW 1LT

W360 ProXL H20 - MIXING YELLOW 500ML

W370 ProXL H20 - ORANGE 500ML

W380 ProXL H20 - LIGHT YELLOW 1LT

W450 ProXL H20 - OXYDE RED 1LT

W460 ProXL H20 - MIXING OXYDE RED 500ML

W470 ProXL H20 - PURPLE 500ML

W480 ProXL H20 - MIXING PURPLE 500ML

W490 ProXL H20 - FULGURANT RED 1LT W510 ProXL H20 - LEMON YELLOW 500ML W530 ProXL H20 - GOLDEN BROWN 1LT W550 ProXL H20 - RUBY RED 1LT

W560 ProXL H20 - PURE MAROON 1LT

W570 ProXL H20 - BRILLIANT MAROON 1LT

W580 ProXL H20 - BRILLIANT RED 1LT

ProXL H2O - SOLID COLOUR

TINTERS



CODE DESCRIPTION SIZE W590 ProXL H20 - GRENATE (1LT) 1LT W810 ProXL H20 - CARBON BLACK (1LT) 1LT W820 ProXL H20 - MIXING BLACK (1LT) 1LT W830 ProXL H20 - EBONY BLACK (1LT) 1LT W850 ProXL H20 - STANDARD BLACK (1LT) 1LT W860 ProXL H20 - GRAYISH BLACK (500ML) 500ML W870 ProXL H20 - DEEP BLACK (1LT) 1LT

CODE DESCRIPTION SIZE W703 ProXL H20 - XIRALLIC COPPER (500ML) 500ML W723 ProXL H20 - XIRALLIC WHITE (500ML) 500ML W733 ProXL H20 - XIRALLIC GOLD (500ML) 500ML W753 ProXL H20 - XIRALLIC RED (500ML) 500ML W773 ProXL H20 - XIRALLIC GREEN (500ML) 500ML W783 ProXL H20 - XIRALLIC BLUE (500ML) 500ML

SOLID & XIRALLIC COLOUR TINTERS

ProXL H2O - XIRALLIC TINTERS

Second Avenue, Chatham Kent, ME4 5AU

CODE DESCRIPTION SIZE W710 ProXL H20 - GOLD DOME 500ML W750 ProXL H20 - FINE RUSSET 1LT W760 ProXL H20 - SPARKLE RED 1LT W920 ProXL H20 - SPARKLE METALLIC 1LT W930 ProXL H20 - METALLIC EXTRA COARSE 1LT W940 ProXL H20 - METALLIC COARSE 1LT W943 ProXL H20 - SILVER DOLLAR COARSE 1LT W950 ProXL H20 - METALLIC FINE 1LT W953 ProXL H20 - SILVER DOLLAR EXTRA FINE 1LT W980 ProXL H20 - METALLIC MEDIUM 1LT W983 ProXL H20 - SILVER DOLLAR FINE 1LT W620 ProXL H20 - PEARL LUSTRE WHITE 1LT W660 ProXL H20 - PEARL BLUE FINE 500ML

W670 ProXL H20 - PEARL BLUISH GREEN 500ML

W680 ProXL H20 - PEARL RED VIOLET 500ML

W690 ProXL H20 - PEARL WHITE FINE 500ML

W700 ProXL H20 - PEARL COPPER 500ML

W720 ProXL H20 - PEARL WHITE 1LT W730 ProXL H20 - PEARL GOLD 1LT

W740 ProXL H20 - PEARL VIOLET 1LT

W770 ProXL H20 - PEARL GREEN 1LT

W780 ProXL H20 - PEARL BLUE 1LT

W790 ProXL H20 - PEARL RED 500ML

METALLIC & PEARL TINTERS



ProXL PRODUCT RANGE

PROCESS

Product

Code

Preparation

Plastic Adhesion Promoter

Easy Application Polyester Filler

XLFLEX

XLSTOP

Primers

Wash Primer

2K HS Acrylic Primer/Filler

XLWASH

XLPRIME

Basecoat

Waterbased Basecoat system

XLBASE

Lacquers

UHS LE Express Clear Lacquer

XLCLEAR

Activators

LE Activator Normal

LE Activator Fast

XLACTN

XLACTF

Thinners Acrylic 2K Thinners (NORMAL) Acrylic 2K Thinners (FAST) Acrylic 2K Thinners (SLOW)

XLTHINN XLTHINF XLTHINS


Description: XLFLEX is an excellent single component plastic primer for adhesion to OEM plastic bumpers. It is a clear liquid, slightly pigmented with a metallic pigment to help with over coating. It creates good adhesion for primer, sealer, or basecoat to these plastic parts.

Suitable Substrates:

Adheres to all plastic car parts, namely: Polypropylene, polyurethane and polyolefin plastics. It is not suitable for PE (polyethylene) parts.

Surface Preparation (untreated plastic):

Temper 60 min.@ 60°C.

___________________________________________________

Abrade surface with an ultra fine pad soaked in WS222 silicone remover

___________________________________________________

Wipe with ProXL WS222 silicone remover.

___________________________________________________

Air dry overnight or 20 min. @ 60°C.

XLFLEX Plastic Primer/

Adhesion Promoter



Application: Ready to spray

___________________________________________________ Compliant 1.3 – 1.4 mm 2.0 – 2.5 bar inlet pressure HVLP 1.4-1.5 mm ; maximum 0.7 bar at the air-cap

___________________________________________________ 1 coat 1-2 microns ___________________________________________________ 10 minutes at 20oC (68oF)

__________________________________________________ Overcoat wet on wet with plasticized ProXL XLPRIME ___________________________________________________

Wear suitable protection

Flash Point: 30oC (86 oF)

Specific Gravity: 0.87 kg/cm3

Solids Content: 5 % by weight

VOC: 810g/l

Coverage: 15 m2/l (theoretical)

SDS: See the safety data sheet


XLFLEX Plastic Primer/

Adhesion Promoter

Description: This great metal filler is a multi-purpose putty with an extremely smooth application. It can be applied vertically without running and exhibits high resistance to almost all solvents. It is characterized by very easy sanding and the advantage of withstanding temperatures of 100°C without any distortions. Suitable Substrates:

Iron, steel plate, glass fiber reinforced plastic Original paints or aged topcoat finishes

Surface preparation:

Clean well the surface to be treated with ProXL WS222. Make sure it is dry and free from Silicone, wax, grease and any extraneous material.

On basecoats or enamel top coats, sand and clean the surface before applying the filler

1 – 3% ProXL hardener Pot life 3 - 5 min at 20oC ____________________________________________________________

Application with putty knife

____________________________________________________________ < 30 min at 20oC ____________________________________________________________ 4 – 5min at 1 m. ____________________________________________________________ Initial Sanding with P60 – P120 roughing-out Final Sanding with P180 – P220 finishing ____________________________________________________________ Composition: unsaturated polyester resin and mineral charges



XLSTOP Easy Polyester Putty

(Beige)

Specific weight: 1.83 ± 0.1

Available colors: Beige

VOC: 250 g/l (EU limit value for this category IIB.b being max. 250g/l)



XLSTOP - Easy Polyester Putty (Beige)

t: +44 (0)1634 823900

e: [email protected] www.capellasolutionsgroup.com

Description: XLWash is an anti-corrosive chromate free adhesion primer used when a high build finish is not required. It has special pigmentation to provide exceptional corrosion protection. XLWash adheres directly to steel sheets and alloys and can be used under all finishes. Suitable Substrates:

o All regular surfaces after degreasing and sanding o Iron sheets o Aluminum and light alloys o Galvanized steel and electro zinc coated sheets o Pre-painted surfaces o Polyesters

Mix 1:1 with XLWASHACT Pot life: 5 to 6 days

18-20 sec / DIN 4 mm / 20oC (68oF)

Spray Nozzle 1.6 – 1.8 mm 3.0 – 4.0 bar inlet pressure HVLP 1.5 -1.8mm; maximum 0.8 bar at the air-cap

_________________________________________________________ 2 coats - 20-25 microns per coat

When build is required, apply one coat followed by any General Primer or sealer. _______________________________________________________

35-40 minutes at 20oC (68oF)

_______________________________________________________

XLWash Wash Primer



t: +44 (0)1634 823900

e: [email protected] www.capellasolutionsgroup.com

Light wet sanding with P500 – P600 grit Light dry sanding with P400 - P500 grit

_______________________________________________________

Clean Surface to remove contamination prior to application of top coat

_______________________________________________________


Flash Point: 12oC (54oF)

Specific Gravity: 1.105 kg/lt Solids Content: 42.5 % by weight pre-dilution VOC: 780 g/l (EU limit value for this category IIB.c being max. 780g/l)

Coverage: 10 – 11 m2/l at 25 micron film thickness (theoretical)


XLWASH - Wash Primer


XLPRIME - 2K Rapid Filler Grey

Description: XLPRIME is a VOC compliant, high build, 2K sanding primer/filler with good vertical stability, outstanding drying performance, good filling properties along with excellent application and sanding properties. _______________________________________________________________________________ Suitable Substrates:

o Existing Finishes except TPA o OEM Primer or EDP, sanded o XLSTOP Polyester Putties o Bare metal substrates must be pre-primed with XLWASH

wash primer _____________________________________________________________

STIR XLPRIME well before mixing

_____________________________________________________________

Mix 4:1:1 XLPRIMEACT activators and thinners Pot life 90 to 120 min / 20oC (68oF) _____________________________________________________________

22-24 sec / DIN 4 mm / 20oC (68oF)

_____________________________________________________________ Compliant 1.6 – 1.8 mm 2.0 – 2.5 bar inlet pressure HVLP 1.7-2.0 mm ; maximum 0.7 bar at the air-cap _____________________________________________________________ 2-3 coats 60 microns per coat _____________________________________________________________ 5-6 minutes at 20oC (6oF) between coats _____________________________________________________________ 2-3 hours at 20oC (68oF) 20mn. at 60oC (140oF)



XLPRIME - 2K Rapid Filler Grey

10 – 15mn. Short Wave The object should be maintained at greater than 60cm from source

Initial Sanding with P500 - P600 grit Final Sanding with P800 - P1000 grit _____________________________________________________________ Initial Sanding with P320 grit Final Sanding with P400 - P500 grit _____________________________________________________________ Clean Surface to remove contamination prior to application of top coat _____________________________________________________________ ProXL H2O basecoat _____________________________________________________________ Wear suitable protection

_____________________________________________________ Flash Point: 25oC (77oF)

_____________________________________________________ Specific Gravity: 1.637 kg/lt

____________________________________________________ Solids Content: 67.8 % by weight – ready to spray

_____________________________________________________ VOC: 485 g/l (EU limit value for this category IIB.c being max. 540g/l)

_____________________________________________________ Coverage: 5.7-5.8 m2/l at 80 micron film thickness (theoretical)

_____________________________________________________

SDS: Refer to the safety data sheet


Description:

ProXL H2O is a premium, high quality Waterborne Automotive Basecoat, which offers outstanding one coat coverage, leading to a high efficiency, and ease of use and complies with all applicable VOC regulations when properly clear coated.


o Original or old Paint o 2K Top-coat o 2K Clear-coat o 2K Primer o ProXL XLPrime

Surface Preparation: o Degrease with ProXL H2O W222 degreaser o Sand and Prime as needed o Finish sand with P800 by hand or P500-600 with

orbital sander. Note: Allow wet-sanded surfaces to thoroughly dry

before Clean-Wipe and painting. o Clean thoroughly with ProXL H2O WS222 Clean-

Wipe to clean substrate free of silicone, dirt, and foreign contaminants. Wipe dry completely before applying color.

o Use only special “Base Coat Tack Rags” that leave no sticky trace behind.

Clear panels prior to painting with ProXL H2O W222 degreaser

Mixing ratio is 1 part ProXL H2O Basecoat to 10% - 20% demineralized water Optimum viscosity 22 to 24 sec/DIN4mm/ 20oC


Automotive Basecoat



HVLP 1.2 – 1.3 2.4-3.0 bar inlet pressure LVLP 1.2 – 1.3 1.6-1.8 bar inlet pressure 1 dust coat 1 full coat 15-25μm 20-30 mins. @ 70°F Flash off time can be reduced by: • Using air blower • Spray booth blower system • Infrared dying • Increasing spray booth temperature

Dust free 20-30 mins. @ 70°F Tack free 20-30 mins. @ 70°F Tape time 45-60 mins. @ 70°F

ProXL H2O clear coats



ProXL H2O -Waterbased Automotive Basecoat

Flash Point: 17oC (55.4oF)

Specific Gravity: 1.47 kg/lt

Solids Content: 61.2 % by weight

VOC: 560 g/lt SDS: See the safety data sheet

ProXL H2O -Waterbased Automotive Basecoat



Email User

Text Box

less than 420 g/ltr

Email User

Text Box

WATERBASED AUTOMOTIVE BASECOAT: Use ProXL H2O and build a future for your business that makes cents. ProXL H2O is user friendly and very cost effective. The transition from conventional to ProXL H2O is easy. Only minor adjustments and a little training are needed. Furthermore, the investment required is minimal. ProXL H2O is a premium, high quality Waterbased Automotive Basecoat, which offers outstanding one coat coverage for high performance, achieving fast drying times and excellent holdout. ProXL H2O is easy to use and complies with all applicable VOC regulations when properly clear coated. COMPONENTS

ProXL H2O Basecoat Base Color ProXL H2O De-mineralized Water WS120 ProXL H2O Basecoat Blending Agent WS135

PHYSICAL DATA Solids content by weight. (Base) 65% (average of colors) Color range Selected Automotive colors VOC as Mixed 0.9 - 3.5 (Max.) lbs/gal; 108 – 420 gr/lt

SUBSTRATES Unsuitable Substrates:

1K Primers, NC Lacquers, Acrylic Lacquers

Suitable Substrates: Original or old Paint – 2K Top-coat & 2K Clear-coat, 2K Primer (ProXL XLPrime)

SURFACE PREPARATION Degrease with ProXL H2O WS222 degreaser Sand and prime with ProXL XLPrime if required Finish sand with P800 by hand; P500-600 with orbital sander; wet sand with P800-1000

Note: Allow surfaces that have been wet-sanded to dry thoroughly before Clean-Wipe and painting.

Clean thoroughly with ProXL H2O WS222 Clean-Wipe to clean substrate free of silicone, dirt, and foreign contaminants. Wipe dry completely before applying color.

Thoroughly sand the surrounding areas that have not been coated with primer surfacer using a fine sanding pad P1200 wet sand paper.

Use only special “Base Coat Tack Rags” that leave no sticky trace behind.


MIXING ProXL H2O tinters should be stirred twice a day. Plastic containers or cans with special lining must be used. To avoid excessive foaming, avoid shaking toners on a paint shaker. Mixing ratio (basecoat color) Mixing ratio is 1 part ProXL H2O Basecoat to 10%-20% ProXL H2O WS120 de-mineralized water. Optimum viscosity is 23 sec. Din 4 cup, or 27 sec # 2 Zahn cup, @ 70° F (~ 20 °C) Strainers with waterproof glue must be used. (125 micron) Avoid using paint shakers after color is made. Stir color thoroughly before application. APPLICATION Use only spray equipment that have stainless steel components and are set up for water application. Gun Setup Gravity Feed HVLP 1.2 mm – 1.3 mm Gravity Feed Compliant LVLP 1.2 mm – 1.3 mm

Air Pressure Conventional Gravity Feed @ gun 35 – 45 psi (2.4 – 3 bars) Conventional Siphon Feed @ gun 40 – 50 psi (2.8 – 3.4 bars)

LVLP gun @ gun 23 – 26 psi (1.6 – 1.8 bars) LVLP gun @ cap 10 – 12 psi (0.7 – 0.8 bars)

Paint Application The application of waterborne products is influenced to a great extent by temperature and air humidity. This may restrict the application or make it more difficult unless certain conditions are fulfilled. Assuming that in an up-to-date paint shop an application temperature of at least 20ºC/68ºF is guaranteed, particular measures are required only with regard to the air humidity if it is outside the application range.


Automotive Basecoat



When relative humidity of air is very high: Excessively high air humidity may cause color deviations, mottling of metallic and effect colors and insufficient settling on upright surfaces. The following measures may be useful.

Increase temperature in the spray booth as far as acceptable for the staff. Choose maximum application viscosity given in Technical data sheet.

When relative humidity of air is very low: Inadequate air humidity may cause increased over spray and insufficient over-spray absorption. The following measures may be useful.

Reduce application temperature if possible. Observe the minimum of 65ºF/18ºC.

Choose lowest possible application viscosity given in the Technical Data Sheet.

Application Techniques Two Stage Solid Colors: Apply light tack coat over repaired area to check any impurities. Holding Spray Gun 6-8” away from the surface, using a 50-60% overlap, apply

base coat to completely cover the repaired area, overlapping slightly onto the original surface at ready to spray viscosity. Spray a wet even coat

Reduce air pressure and fade out into the blend area. No flash off times between coats

Two Stage Effect Colors “Metallic and Pearls”: Apply light tack coat over repaired area to check any impurities. Holding Spray Gun 6-8” away from the surface, using a 50-70% overlap, apply base

coat to completely cover the repaired area, overlapping slightly onto the original surface at ready to spray viscosity. Spray a wet even coat

Let the coating flash off completely. Hold the Spray Gun 12-18 inches away from the painted surface and apply a quick

even orientation coat to organize the effect. Reduce the air pressure and fade out into the blend area. Generally, no further

painting is required, even on those difficult colors! If you would like to step out your blend with a further reduced color use ProXL H2O WS135 Blending Agent.

ProXL H2O - Waterbased Automotive Basecoat


Use ProXL H2O WS135 Blending agent by taking ready to spray color and adding 20%-50% of blending agent then reduce pressure and fade out over the blend area. Be sure to avoid getting too close to the end of the blend panel. Over coating Surface must always be allowed to matte completely before clear coat is applied. Apply clear after the basecoat has become a matt finish Clear topcoat must be applied after:

• 5 hours - solid colors at 20oC • 48 hours - metallic/pearl colors at 20oc

DRYING PERFORMANCE Small Areas Surface matting can be accelerated by blow-drying with air diffuser after a 5 minute flash off time Dry panel by blowing across the plane of the surface working from the back of the panel to the front.

Air Dry @ 70° F Blow dry with (air diffuser) Flash time 20-30 minutes 7-10 minutes Tape time 45-60 minutes 35-45 minutes Tack free 20-30 minutes 7-10 minutes Dust free 20-30 minutes 7-10minutes Large Areas Surface matting can be accelerated by using infrared or low bake cycle.

IR Short wave 3-5 minutes IR medium wave 4-7 minutes Cooling time 5-7 minutes For paint booths equipped for baking cycle:

Low bake 140º F/60º C 10 minutes. Cooling time 5-7 minutes Note: Longer bake cycles can cause loss of inter-coat adhesion. Note: Flash and Dry times will vary depending on humidity, airflow in the booth, number of coats applied and ambient temperature in the booth.




TRANSPORT AND STORAGE Anyone Handling, Storing or Transporting this product must insure that the temperature should not fall below 5ºC/42ºF or rise above 35ºC/95ºF. Temperatures above or below this range will lead to loss of product quality. CLEAN UP See Technical Data Sheet – ProXL H2O Cleaning equipment and spray guns and waste management. IMPORTANT REGULATORY INFORMATION: The values depicted below are “as applied regulatory” for the base coat alone. Values have been determined using EPA Test Method 24. EU - VOC Regulatory Maximum 420g/l For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read all label and MSDS precautions. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, expressed or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and, or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. SAFETY Refer to Material Safety Data Sheet (MSDS) for complete safety instructions. The technical data sheet listed has been compiled in good faith for your convenience and guidance. No warranty, expressed or implied, is intended or given by the information on this sheet.



When cleaning equipment and spray guns, waste disposal should be taken into consideration and priority given to avoiding waste. The use of water-borne products can reduce disposal costs. ProXL H2O S120 de-mineralized water is used for reducing of ProXL H2O base-coat. For cleaning spray guns and equipment, water can be used provided the spray guns are carefully emptied of base-coat color after use. Water contaminated by cleaning other utensils can be used to rinse out used spray guns.

CLEANING SPRAY GUNS: Empty remaining ProXL H2O color from the gun into a waste container kept

separate from solvent waste. Clean gun with water. Remove sticking, dried water-borne paint residue with a cleaning solvent

compliant for your area. After cleaning, or prior to further use, rinse gun out with water.

CLEANING OTHER EQUIPMENT (MEASURING STICKS, VISCOSITY CUPS, AND MIXING CONTAINERS).

Remove wet deposits with water. Remove sticking, dried water-borne paint residue with cleaning solvent

compliant for your area. Important note: Contaminated water must never be mixed with contaminated conventional cleaning solvents, as this makes disposal difficult and therefore more expensive, if not impossible.

Cleaning procedure for ProXL H2O

Waterbased Basecoats



Description: XLCLEAR is a VOC compliant, 2K UHS, high quality, lacquer with good vertical stability, quick drying times, and excellent gloss finish along with very good polishing properties.


o ProXL H2O Basecoat.

Mix 2:1 with XLACTN or XLACTF activator Pot life 60 min / 20oC (68oF)

18-20 sec / DIN 4 mm / 20oC (68oF)

Compliant 1.3 – 1.4 mm 2.0 – 2.5 bar inlet pressure HVLP 1.3 - 1.4 mm; 0.7 bar at the air-cap

1 clinging coat + 1 full coat 50- 60 microns per coat

5-10 minutes at 20oC (68oF)

20-25 min. at 60oC (140oF) panel temperature.

XLCLEAR 2k UHS Clear

Lacquer


10 – 12 min. Short Wave The object should be maintained at greater than 60cm from source


Flash Point: 24oC (74oF) Solids Content: 58 % by weight – ready to spray VOC: Max 420 g/l (EU limit value for this category IIB.d being max. 420g/l) Coverage: 9-10 m2/l at 50 micron film thickness (theoretical) SDS: See the safety data sheet

XLCLEAR - 2k UHS Clear Lacquer



pro-xl h2o water-based paint - try it !

Automotive

w530 proxl h2

w110 proxl h2

w340 proxl h2

w490 proxl h2

w380 proxl h2

w350 proxl h2

w470 proxl h2

w480 proxl h2