product certifications document: rosemount 2140 and 2140:sis … · 2020. 11. 17. · can/csa c22.2...

Product Certifications00825-0200-4140, Rev AG

September 2020

Rosemount™ 2140 and 2140:SIS LevelDetectors

Vibrating Fork

1 Product certifications

1.1 Safety messages

NoteOther language versions of this Product Certifications Document can befound at Emerson.com/Rosemount.

WARNING

Failure to follow safe installation and servicing guidelines could result indeath or serious injury.

• This document contains information required for compliance with thecertifications.

• Use the level detector only as specified in this document and the productreference manual. Failure to do so may impair the protection providedby the level detector. Refer to the Rosemount 2140 and 2140:SIS LevelDetectors Reference Manual for more instructions.

• The weight of a level detector with a heavy flange and extended forklength may exceed 37 lb. (18 kg). A risk assessment is required beforecarrying, lifting, and installing the level detector.

Explosions could result in death or serious injury.

• Verify that the operating atmosphere of the level detector is consistentwith the appropriate hazardous locations certifications.

• Before connecting a handheld communicator in an explosiveatmosphere, ensure that the instruments in the loop are installed inaccordance with intrinsically safe or non-incendive field wiring practices.

• In explosion-proof/flameproof and non-incendive/type n installations, donot remove the housing covers when power is applied to the leveldetector.

• Both housing covers must be fully engaged to meet flameproof/explosion-proof requirements.

Product Certifications September 2020

2 Rosemount 2140 and 2160:SIS Level Detectors

https://www.emerson.com/en-us/automation/rosemount

https://www.emerson.com/documents/automation/manual-rosemount-2140-level-detector-vibrating-fork-en-us-187106.pdf

WARNING

Electrical shock could cause death or serious injury.

• Avoid contact with the leads and terminals. High voltage that may bepresent on leads can cause electrical shock.

• Ensure the power to the level detector is off, and the lines to any otherexternal power source are disconnected or not powered while wiring thelevel detector.

• Ensure the wiring is suitable for the electrical current and the insulation issuitable for the voltage, temperature, and environment.

Process leaks could result in death or serious injury.

• Ensure the level detector is handled carefully. If the process seal isdamaged, gas might escape from the vessel (tank) or pipe.

WARNING

Physical access

Unauthorized personnel may potentially cause significant damage to and/ormisconfiguration of end users’ equipment. This could be intentional orunintentional and needs to be protected against.

Physical security is an important part of any security program andfundamental to protecting your system. Restrict physical access byunauthorized personnel to protect end users’ assets. This is true for allsystems used within the facility.

CAUTION

Hot surfacesThe flange and process seal may be hot at high processtemperatures.

Allow to cool before servicing.

CAUTION

Refer to manualThis document contains information required to safely install,connect, commission, operate and maintain, and is required forcertification compliance.

September 2020 Product Certifications

Product Certifications 3

1.2 European Union directive informationA copy of the EU Declaration of Conformity certificate can be found in thesection EU Declaration of Conformity. The most recent revision of thecertificate can be found at Emerson.com/Rosemount.

1.3 Ordinary location certifications1.3.1 U.S.A. Ordinary Location certification

G5

Summary of product certification:

Protection Ordinary location (unclassified, safe area)

Certificate 70098390

Standard UL 61010-1: 2012

Marking Type 4X

The level detector has been examined and tested to determine that thedesign meets basic electrical, mechanical, and fire protection requirementsby CSA, a nationally recognized testing laboratory (NRTL) as accredited bythe Federal Occupational Safety and Health Administration (OSHA).

Special Condition For Use

To be supplied from a Class 2 or Limited Energy Source in accordance withCAN/CSA C22.2 No. 61010-1-12.

1.3.2 Canada Ordinary Location certification

G6

Summary of product certification:

Protection Ordinary location (unclassified, safe area)


Standards CAN/CSA C22.2 No 61010-1-12

ANSI/ISA-12.27.01:2011

Marking Type 4X

Single process seal

The level detector has been examined and tested to determine that thedesign meets basic electrical, mechanical, and fire protection requirementsby CSA, a nationally recognized testing laboratory (NRTL) as accredited bythe Federal Occupational Safety and Health Administration (OSHA).



https://www.emerson.com/en-us/automation/rosemount

Special Condition For Use

To be supplied from a Class 2 or Limited Energy Source in accordance withCAN/CSA C22.2 No. 61010-1-12.

1.4 USA1.4.1 U.S.A. Explosion-proof and Division 2 (XP)

E5

Summary of product certification

Protection Explosion-proof (XP)


Standards FM Class 3600 - 2011

M Class 3615 - 2015

UL 61010-1: 2012

Markings Class I Groups B, C and D, T6...T2

Class I Division 2 Groups A, B, C and D, Type 4X

Class I, Zone 1, AEx db IIC T6…T2 Gb

Temperatures See Flameproof and explosion-proof approval temperatures

Safetyinstructions

See Instructions for hazardous area installations

Special Conditions For Use (X)

1. The user is to ensure the probe assembly is installed in such a way toprevent any damage due to impact or ignition source due to friction.

2. The enclosure may be given a non-standard paint finish which mayconstitute a potential electrostatic ignition risk. Care should be takento protect it from external conditions conducive to the build-up ofelectrostatic charge on such surfaces. The enclosure must not berubbed or cleaned with a dry cloth.

3. Flameproof joints are not intended for repair.

4. To be supplied from a Class 2 or Limited Energy Source in accordancewith CAN/CSA C22.2 No. 61010-1-12.



1.4.2 U.S.A. Intrinsic Safety (IS) and Non-Incendive (NI)

I5


Protection Intrinsic Safety (IS) and Non-Incendive (NI)


Standards FM Class 3600:2011

FM Class 3610:2015

FM Class 3611:2004

Markings Class I Groups A, B, C and D, T5…T2

Class I, Division 2, Groups A, B, C, and D, Type 4X

Class I, Zone 0, AEx ia IIC T5…T2 Ga

Controldrawing

71097/1387 (see Installation drawings)

Temperatures See Intrinsically Safe (IS) approval temperatures

Safetyinstructions


Special Conditions For Safe Use (X)

1. The equipment, when fitted with the transient suppression terminalblock, is not capable of withstanding the 500 volt insulation test. Thismust be taken into account when installing the equipment.

2. The enclosure may be made of aluminum alloy and given a protectivepolyurethane paint finish. However, care should be taken to protectit from impact or abrasion if located in Zone 0.




1.5 Canada1.5.1 Canada Explosion-proof and Division 2 (XP)

E6


Protection Explosion-proof (XP)


Standards ANSI/ISA 12.27.01:2011

CSA Std. C22.2 No. 30 -M1986

CSA Std. C22.2 No.60079-0-15

CSA Std. C22.2. No.60079-1-16

CSA Std. C22.2 No. 61010-1-12

CSA Std. C22.2 No.94-M91

CSA Std. C22.2 No. 213-2016

Markings Class I Groups B, C and D, T6...T2

Class I Division 2 Groups A, B, C and D, Type 4X

Ex db IIC T6…T2 Gb, single seal


Safetyinstructions






4. To be supplied from a Class 2 or Limited Energy Source in accordancewith CAN/CSA C22.2 No. 61010-1-12.



1.5.2 Canada Intrinsic Safety (IS) and Non-Incendive (NI)

I6


Protection Intrinsic Safety (IS) and Non-Incendive (NI)


Standards ANSI/ISA 12.27.01:2011

CSA Std. C22.2 No. 157 -92

CSA Std. C22.2 No. 60079-0-15

CSA Std. C22.2. No. 60079-11-14

Markings Class I Groups A, B, C and D, T5…T2

Class I, Division 2, Groups A, B, C, and D, Type 4X

Ex ia IIC T5…T2 Ga, single seal

Controldrawing

71097/1387 (see Installation drawings)


Safetyinstructions






1.5.3 Canadian Registration Number

CRN 0F04227.2C

The requirements of CRN are met when a Rosemount 2140 Level Detector isconfigured with 316/316L stainless steel (1.4401/1.4404) process-wettedparts and either NPT threaded or 2-in. to 8-in. ASME B16.5 flanged processconnections.



1.6 Europe1.6.1 ATEX Flameproof (FLP) and Dust Proof (DP)

E1


Protection Flameproof (FLP)

Certificate Dekra 16ATEX0082X

Standards EN60079-0:2012+A11:2013

EN60079-1:2014

EN60079-26:2015

Markings II 1/2 G

Ex db IIC T6...T2 Ga/Gb


Safetyinstructions




2. Non-standard paint options may cause risk from electrostaticdischarge. Avoid installations that could cause electrostatic build-upof painted surfaces, and only clean the painted surfaces with a dampcloth. If paint is ordered through a special option code, contact themanufacturer for more information.


ND


Protection Dust Proof (DP)

Certificate Baseefa 16ATEX0137X

Standards IEC EN 60079-0:2018

EN60079-31:2014

Markings II 1 D, Ex ta IIIC (T92 °C…T272°C)

(T200100°C…T200280 °C) Da

Temperatures See Dust approval temperatures

Safetyinstructions





1. Cable entries must maintain the ingress protection rating of theenclosure to at least IP66.

2. Unused cable entries must be filled with suitable blanking plugswhich maintain the ingress protection of the enclosure to at leastIP66.

3. Cable entries and blanking plugs must be suitable for the ambienttemperature of the equipment and be capable of withstanding a 7Jimpact test.


E8 combines E1 and ND

Temperatures See Flameproof and explosion-proof approval temperatures andDust approval temperatures

Safetyinstructions









7. The enclosure may be given a non-standard paint finish which mayconstitute a potential electrostatic ignition risk. Care should be taken



to protect it from external conditions conducive to the build-up ofelectrostatic charge on such surfaces. The enclosure must not berubbed or cleaned with a dry cloth.

1.6.2 ATEX Intrinsic Safety (IS)

I1


Protection Intrinsic Safety (IS) and Dust (Zone 0, 20)

Certificates Baseefa 16ATEX0136X and Baseefa 16ATEX0137X


EN60079-11:2012

EN60079-26:2015

EN60079-31:2014

Markings II 1 G, Ex ia IIC T5...T2 Ga

II 1 D, Ex ta IIIC (T92 °C...T272 °C)

(T200100°C...T200280 °C) Da

Electricalparameters

Ui = 30 V, Ii = 100 mA, Pi = 0.9 W, Ci = 0.012 μF, and Li = 0 mH


Safetyinstructions











I8


Protection Intrinsic Safety (IS) (Zone 1)

Certificate Baseefa 16ATEX0136X


EN60079-11:2012

EN60079-26:2015

Markings II 1/2 G, Ex ib IIC T5...T2 Ga/Gb




Safetyinstructions








1.7 International1.7.1 IECEx Flameproof (FLP) and Dust

E7

(E7 also includes the NK approval)


Protection Flameproof and dust-proof

Certificates IECEx DEK 16.0040X and IECEx BAS 16.0106X

Standards IEC60079-0:2017

IEC60079-1:2014

IEC60079-26:2014

IEC60079-31:2013

Markings Ex db IIC T6...T2 Ga/Gb

Ex ta IIIC (T92°C…T272°C) (T200100°C…T200280°C) Da


See Dust approval temperatures

Safetyinstructions








1.7.2 IECEx Intrinsic Safety (IS)

I7


Protection Intrinsic Safety (IS)

Certificates IECEx BAS 16.0105X


IEC60079-11:2011

Markings Ex ia IIC T5...T2 Ga




Safetyinstructions






1.7.3 IECEx Dust

NK


Protection Dust

Certificates IECEx BAS 16.0106X


IEC60079-31:2013

Markings Ex ta IIIC (T92°C…T272°C) (T200100°C…T200280°C) Da

Temperatures See Dust approval temperatures



Safetyinstructions







1.8 Brazil1.8.1 INMETRO Flameproof (FLP)

E2


Protection Flameproof

Certificates UL-BR 017.0843X

Standards ANBT NBR IEC 60079-0:2013

ABNT NBR IEC 60079-1:2016

ABNT NBR IEC 60079-26:2016

Markings Ex db IIC T6…T2 Ga/Gb


Safetyinstructions




2. The sensor probe shall be handled and installed to avoid friction anddamage from impact.




1.8.2 INMETRO Intrinsic Safety (IS)

I2



Certificates UL-BR 17.0837X

Standards ANBT NBR IEC 60079-0:2013

ABNT NBR IEC 60079-11:2013

Markings Ex ia IIC T5…T2 Ga




Safetyinstructions




2. The enclosure may be made of aluminum alloy and given a protectivepolyurethane paint finish. However, care should be taken to protectit from impact or abrasion if located in areas that require EPL Ga(Zone 0).




1.9 China1.9.1 NEPSI Flameproof and Dust

E3


Protection Flameproof and dust

Certificate GYJ20.1386X (CCC 认证)

Standards GB 3836.1-2010

GB 3836.2-2010

GB 12476.1-2013

GB 12476.5-2013

Markings Ex d IIC T6~T2 Ga/Gb

Ex td A20 T92°C~T272°C) (T200100°C~T200280°C)

IP66



Safetyinstructions



See certificate for special conditions.

1.9.2 NEPSI Intrinsic Safety (IS)

I3



Certificate GYJ20.1385X (CCC 认证)

Standards GB 3836.1-2010

GB 3836.4-2010

Markings Ex ia IIC T5~T2 Ga


Ui = 30 V, Ii = 100 mA, Pi = 0.9 W, Ci = 12 nF, and Li = 0 mH


Safetyinstructions




https://www.emerson.com/en-us/catalog/rosemount-sku-2140-detector-vibrating-fork

https://www.emerson.com/en-us/catalog/rosemount-sku-2140-detector-vibrating-fork



1.10 Russia1.10.1 Technical Regulation Customs Union (EAC) Flameproof and Dust

EM


Protection Flameproof and dust

Certificate TC RU C-GB.AA87.В.00728

Markings Ex db IIC T6…T2 X

Ex ta IIIC T92°C…T272°C T500100°C…T500280°C Da X



Safetyinstructions




1.10.2 Technical Regulation Customs Union (EAC) Intrinsic Safety (IS)

IM



Certificate TC RU C-GB.AA87.В.00728

Markings OEx ia IIC T5…T2 Ga X




Safetyinstructions



See certificate for special conditions



1.11 India1.11.1 CCOE Flameproof

E1


Protection Flameproof

Certificate P408160/1

Standards EN60079-0:2012+A11:2013

EN60079-1:2014

EN60079-26:2015

Markings Ex db IIC T6...T2 Ga/Gb


Safetyinstructions






1.11.2 CCOE Intrinsic Safety (IS)

I1



Certificate P408161/1

Markings EN60079-0:2012+A11:2013

EN60079-11:2012

EN60079-26:2015






Safetyinstructions






1.12 Combinations of approvals

K1 Combines I1 and E1

K5 Combines I5 and E5

KB Combines I5, I6, E5, and E6

KZ Combines G5 and G6

1.13 Instructions for hazardous area installations

1.13.1 General safety

1. Installation of this equipment shall be carried out by suitably trainedpersonnel, in accordance with the applicable code of practice.

2. Inspection and maintenance of this equipment shall be carried out bysuitably trained personnel, in accordance with the applicable code ofpractice.

3. The user should not repair this equipment.

4. The certification of this equipment relies upon the followingmaterials used in its construction:

Housing and cover Aluminum alloy ASTM B85 A360.0 orstainless steel 316C12

Probe (partitionwall)

Stainless steel 316/316L, or UNS N10276,or UNS N10002, or UNS N30002



Seals Silicone

5. If equipment is likely to come into contact with aggressivesubstances, it is the user’s responsibility to take suitable precautionsthat prevent it from being adversely affected, thus ensuring the typeof protection is not compromised.Aggressive substances: Acidic liquids or gases that may attackmetals or solvents that may affect polymeric materials.Suitable precautions: Regular checks as part of routine inspectionsor establishing from a material's data sheet that it is resistant tospecific chemicals.

6. It is the responsibility of the user to ensure:a. The voltage and current limits for this equipment are not

exceeded.

b. The joint requirements between the probe and the vesseltank are compatible with the process media.

c. The joint tightness is correct for the joint material used.

d. Safe working practices for the media and process concernedare followed during the installation and maintenance of theequipment.

7. The probe fork is subjected to small vibration stresses as part of itsnormal function. As this provides a partition wall, it is recommendedthat the fork should be inspected every two years for signs of defects.

8. Technical dataa. The operating pressure must not exceed the rating of the

fitted coupling or flange.

b. For material details and pressure ratings, refer to theRosemount 2140 and 2140:SIS Level Detectors Product DataSheet.

c. Year of manufacture is marked on the product label.

1.13.2 ATEX specific instructions

The equipment has not been assessed as a safety related device (as referredto by directive 2014/34/EU Annex II, clause 1.5).

1.13.3 Intrinsic Safety specific instructions

1. The Rosemount 2140 and 2140:SIS may be used in a hazardous areawith flammable gases and vapors with apparatus groups IIA, IIB andIIC, and temperature classes T1 to T6. The temperature class of the



https://www.emerson.com/documents/automation/product-data-sheet-rosemount-2140-level-detector-en-us-187110.pdf

https://www.emerson.com/documents/automation/product-data-sheet-rosemount-2140-level-detector-en-us-187110.pdf

installation will be determined from the highest process or ambienttemperature.

2. The equipment with Product Certifications code “I8” is suitable forinstallation across the boundary between an area that specificallyrequires Equipment Protection Level Ga (Zone 0) and an area thatspecifically requires Equipment Protection Level Gb (Zone 1). Theprobe forks (and extension tube) are only to be installed in Zone 0.

3. When fitted with the Transient Protection Terminal Block (optioncode T1), the unit does not meet the requirements of clause 6.3.13(Isolation of circuits from earth or frame) in EN 60079-11:2012 (IEC60079-11:2011).

4. Electrical parameters: Ui: 30 V, Ii: 100 mA, Pi: 0.9 W, Ci: 0.012 μF, Li: 0mH

1.13.4 Flameproof and explosion-proof specific instructions

1. The Rosemount 2140 and 2140:SIS may be used in a hazardous areawith flammable gases and vapors with apparatus groups IIA, IIB andIIC, and temperature classes T1 to T6. The temperature class of theinstallation will be determined from the highest process or ambienttemperature.

2. The equipment is suitable for installation across the boundarybetween an area that specifically requires Equipment ProtectionLevel Ga (Zone 0) and an area that specifically requires EquipmentProtection Level Gb (Zone 1). The probe forks (and extension tube)are only to be installed in Zone 0.

3. Repair or modification of flame-paths is not permitted.

4. It is the responsibility of the user to ensure:a. The housing anti-rotation grub screw is screwed in fully.

b. The housing cover locking screws are unscrewed tightlyagainst the covers.

c. Only suitably certified cable entry devices will be utilizedwhen connecting this equipment. The cable entrytemperature may exceed 70 °C.

d. That suitable temperature rated cable is used. Forconnections in an ambient in excess of 60 °C, use cable ratedto at least 90 °C.

e. That any unused cable entries are sealed with suitablycertified stopping plugs.

f. The protective earth terminal is connected to an externalprotective earthing system.



5. Only screws and fittings provided by the manufacturer can beattached to the housing.

6. Electrical parameters: Vmax = 42.4 Vdc, Imax = 23.5 mA

1.13.5 Dust (protection by enclosure) specific instructions

1. The Rosemount 2140 and 2140:SIS may be used in a hazardous areawith flammable gases and vapors with apparatus groups IIA, IIB andIIC, and temperature classes T1 to T5. The temperature class of theinstallation will be determined from the highest process or ambienttemperature.

2. It is the responsibility of the user to ensure:a. The housing anti-rotation grub screw is screwed in fully.

b. The housing cover locking screws are unscrewed tightlyagainst the covers.

c. Only suitably certified cable entry devices will be utilizedwhen connecting this equipment. The cable entrytemperature may exceed 70 °C.

d. That suitable temperature rated cable is used. Forconnections in an ambient in excess of 60 °C, use cable ratedto at least 90 °C.



1.14 Intrinsically Safe (IS) approval temperatures

Figure 1-1: 2140****M* Temperature De-rating (Intrinsically Safe)

6.263"

T4...T1

T5...T1 T3...T1

70

60.7

53

40

0

-60-40 0 9570 130 180

Process Temperature (°C)

Am

bien

t Tem

pera

ture

(°C

)

Figure 1-2: 2140****E* Temperature De-rating (Intrinsically Safe)

T5...T1 T3...T1 T2...T1

70

60

40

66.8 63.4

0

-60-70 0 9570 130 195 260

T4...T1


Am

bien

t Tem

pera

ture

(°C

)



1.15 Flameproof and explosion-proof approval temperatures

Figure 1-3: 2140****M* Temperature De-rating (Flameproof/Explosion-proof)

T5...T1

T6...T1 T4...T1 T3...T1

80

77706560

0

-40-40 0 80 95 130 180


Am

bien

t Tem

pera

ture

(°C)

Figure 1-4: 2140****E* Temperature De-rating (Flameproof/Explosion-proof)

T5...T1

T6...T1 T4...T1 T3...T1 T2...T1

8079 77

7073.5

0

65

-40-70 0 80 95 130 195 260


Am

bien

t Tem

pera

ture

(°C

)



1.16 Dust approval temperaturesMinimum ambient air temperature (Ta) = -20 °C

Figure 1-5: 2140****M* Maximum Surface Temperature

200

10092

19280

60

8000

-40 180

Ambient

T500***°C

T***°C


Surf

ace

Tem

pera

ture

(°C

)

Max

imum

Am

bien

t Tem

pera

ture

(°C

)

Figure 1-6: 2140****E* Maximum Surface Temperature

Ambient

T500***°C

T***°C

280

10092

27280

70

8000-70 260


Surf

ace

Tem

pera

ture

(°C

)

Am

bien

t Tem

pera

ture

(°C

)



1.17 Installation drawings

Figure 1-7: USA and Canada installation drawing 71097/1387 (Page 1)

APPROVAL

TITLE

APPR.DRG. I.S. &

NONINCENDIVE

CONTROL DRAWING FOR

ROSEMOUNT 2140

DOCUMENT NUMBER: -

71097/1387

Page 1 of 5

AB 24/01/17 MBY-05601 GP DRAWN JPA 19/10/16

REVISION DATE ECO No. NAME APPROVED SEE ECO

L2073 Iss. AA© ROSEMOUNT MEASUREMENT LIMITED 2017

THE REPRODUCTION, DISTRIBUTION, & UTILISATION OF THIS DOCUMENT AS WELL AS THE COMMUNICATION OF ITS

CONTENTS TO OTHERS WITHOUT EXPRESS AUTHORISATION IS PROHIBITED. OFFENDERS WILL BE HELD LIABLE FOR

PAYMENT OF DAMAGES. ALL RIGHTS RESERVED IN THE EVENT OF PATENT, UTILITY MODEL OR DESIGN.

CERTIFIED PRODUCT: ALTERATIONS TO THIS DOCUMENT MUST BE APPROVED BEFORE IMPLEMENTATION.

GENERAL NOTES:

1. ASSOCIATED APPARATUS MANUFACTURER'S INSTALLATION DRAWINGMUST BE FOLLOWED WHEN INSTALLING THIS EQUIPMENT.

2. CONTROL EQUIPMENT CONNECTED TO BARRIER MUST NOTUSE OR GENERATE MORE THAN 250 Vrms or Vdc,

3. RESISTANCE BETWEEN INTRINSICALLY SAFE GROUND ANDEARTH GROUND MUST BE LESS THAN 1 OHM,

4. INSTALLATION SHOULD BE IN ACCORDANCE WITH APPLICABLELAWS/REGULATIONS AND CODE OR PRACTICE. I.E. FOR CANADA,THE CANADIAN ELECTRICAL CODE (CSA C22.1);FOR AMERICA, THE NATIONAL ELECTRICAL CODE (ANSI/NFPA 70)AND ANSI/ISA-RP12.6 “INSTALLATION OF INTRINSICALLY SAFESYSTEMS FOR HAZARDOUS (CLASSIFIED) LOCATIONS”.

5. THE ASSOCIATED APPARATUS, BARRIER OR ISOLATOR MUST BE APPROVED.FOR CANADA, TO CANADIAN STANDARDS BY AN NRTL ACCREDITED BY THESTANDARDS COUNCIL OF CANADA (SCC).FOR AMERICA, TO AMERICAN STANDARDS BY AN NRTL ACCREDITED BYTHE OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA).

6. WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIRINTRINSIC AND NON-INCENDIVE SAFETY, AVERTISSEMENT: LA SUBSTITUTION DE COMPOSANTS PEUTCOMPROMETTRE LA SÉCURITÉ INTRINSÈQUE ET LA SÉCURITÉNON INCENDIAIRIES

7. ASSOCIATED APPARATUS MUST MEET THE FOLLOWING PARAMETERS:Uo or Voc or Vt LESS THAN or EQUAL TO Ui (Vmax)Io or Isc or It LESS THAN or EQUAL TO Ii (Imax)Po or Pmax LESS THAN or EQUAL TO Pi (Pmax)Ca IS GREATER THAN or EQUAL THE SUM OF ALL Ci's PLUS CcableLa IS GREATER THAN or EQUAL THE SUM OF ALL Li's PLUS Lcable

8. THE ASSOCIATED APPARATUS MUST BE A RESISTIVELY LIMITED SINGLE OR MULTIPLE CHANNEL APPROVED BARRIER HAVING PARAMETERS LESS THAN THOSEQUOTED, AND FOR WHICH THE OUTPUT AND THE COMBINATIONS OF OUTPUTS ISNON-IGNITION CAPABLE FOR THE CLASS, DIVISION AND GROUP OF USE,

9. FIELD WIRING SHOULD BE RATED TO 70°C MINIMUM,




APPROVAL

TITLE

APPR.DRG. I.S. &

NONINCENDIVE

CONTROL DRAWING FOR

ROSEMOUNT 2140

DOCUMENT NUMBER: -

71097/1387

Page 2 of 5



L2073 Iss. AA

© ROSEMOUNT MEASUREMENT LIMITED 2017





DIV 1 INSTALLATION OPTIONS

THE ROSEMOUNT TRANSMITTER IS APPROVED AS INTRINSICALLY SAFE WHEN USED IN CIRCUIT WITH APPROVEDBARRIERS WHICH MEET THE ENTITY PARAMETERS LISTED IN THE CLASS I. DIVISION 1 GROUPS INDICATED.ADDITIONALLY, THE ROSEMOUNT 751 FIELD SIGNAL INDICATOR IS APPROVED AS INTRINSICALLY SAFE WHEN CONNECTED IN CIRCUIT WITH ROSEMOUNT TRANSMITTERS AND APPROVED BARRIERS WHICH MEET THE ENTITY PARAMETERS LISTED FOR CLASS I, DIVISION 1, GROUPS INDICATED.

TO ASSURE AN INTRINSICALLY SAFE SYSTEM. THE TRANSMITTER AND BARRIER MUST BE WIRED IN ACCORDANCEWITH THE BARRIER MANUFACTURER'S FIELD WIRING INSTRUCTIONS AND THE APPLICABLE CIRCUIT DIAGRAM.




APPROVAL

TITLE

APPR.DRG. I.S. &

NONINCENDIVE

CONTROL DRAWING FOR

ROSEMOUNT 2140

DOCUMENT NUMBER: -

71097/1387

Page 3 of 5








ENTITY CONCEPT APPROVALSTHE ENTITY CONCEPT ALLOWS INTERCONNECTION OF INTRINSICALLY SAFE APPARATUS TO ASSOCIATED APPARATUS NOT SPECIFICALLY EXAMINED IN COMBINATION AS A SYSTEM. THE APPROVED VALUES OF MAX. OPEN CIRCUIT VOLTAGE (Voc OR Vt) AND MAX. SHORT CIRCUIT CURRENT (Isc OR It) AND MAX,POWER (Voc X Isc/4) OR (Vt X It/4), FOR THE ASSOCIATED APPARATUS MUST BE LESS THAN OR EQUAL TO THE MAXIMUM SAFE INPUT VOLTAGE (Vmax), MAXIMUM SAFE INPUT CURRENT (Imax), AND MAXIMUM SAFE INPUT POWER (Pmax) OF THE INTRINSICALLY SAFE APPARATUS. IN ADDITION, THE APPROVED MAX. ALLOWABLECONNECTED CAPACITANCE (Ca) OF THE ASSOCIATED APPARATUS MUST BE GREATER THAN THE SUM OF THE INTERCONNECTING CABLE CAPACITANCE AND THE UNPROTECTED INTERNAL CAPACITANCE (Ci) OF THE INTRINSICALLY SAFE APPARATUS, AND THE APPROVED MAX. ALLOWABLE CONNECTED INDUCTANCE (La) OF THE ASSOCIATED APPARATUS MUST BE GREATER THAN THE SUM OF THE INTERCONNECTING CABLE INDUCTANCE AND THE UNPROTECTED INTERNAL INDUCTANCE (Li) OF THE INTRINSICALLY SAFE APPARATUS,

NOTE: ENTITY PARAMETERS LISTED APPLY ONLY TO ASSOCIATED APPARATUS WITH LINEAR OUTPUT.

Vmax= 30V Vt OR Voc IS LESS THAN OR EQUAL TO 30V

Imax = 100mA It OR Isc IS LESS THAN OR EQUAL TO 100mA

Pmax = 0.9 WATT ( ) OR ( ) IS LESS THAN OR EQUAL TO 0.9 WATT

Ci = 0.012µF Ca IS GREATER THAN 0.012µF

Li = 0mH La IS GREATER THAN 0mH

CLASS I, DIV 1, GROUPS A AND B

CLASS I, DIV 1, GROUPS C AND D

Vmax= 30V Vt OR Voc IS LESS THAN OR EQUAL TO 30V

Imax = 100mA It OR Isc IS LESS THAN OR EQUAL TO 100mA

Pmax = 0.9 WATT ( ) OR ( ) IS LESS THAN OR EQUAL TO 0.9 WATT

Ci = 0.012µF Ca IS GREATER THAN 0.012µF

Li = 0mH La IS GREATER THAN 0mH

DIV 2 INSTALLATION OPTIONS




APPROVAL

TITLE

APPR.DRG. I.S. &

NONINCENDIVE

CONTROL DRAWING FOR

ROSEMOUNT 2140

DOCUMENT NUMBER: -

71097/1387

Page 4 of 5



L2073 Iss. AA

© ROSEMOUNT MEASUREMENT LIMITED 2017





CLASS I, DIV.2 HAZARDOUS (CLASSIFIED) LOCATION

APPROVED

ASSOCIATED

NONINCENDIVE

APPARATUS [1]

UNSPECIFIED

EQUIPMENT [3]

UNCLASSIFIED

LOCATION

MECHANICALLY

PROTECTED

WIRE PER APPLICABLE

ELECTRICAL CODE

NOTES:

[1] ASSOCIATED NON-INCENDIVE APPARATUS PARAMETERS SHALL BE THE SAME AS THOSE SHOWN ON PAGE 3

[2] MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE ELECTRIC CODE FOR WIRING IN DIVISION 2 HAZARDOUS (CLASSIFIED) LOCATIONS.

[3] SUPPLIED BY A CLASS 2 OR LIMITED ENERGY SOURCE IN ACCORDANCE WITH CAN/CSA-C22.2 No. 61010-1-12




APPROVAL

TITLE

APPR.DRG. I.S. &

NONINCENDIVE

CONTROL DRAWING FOR

ROSEMOUNT 2140

DOCUMENT NUMBER: -

71097/1387

Page 5 of 5








NONINCENDIVE FIELD CIRCUITCLASS I. DIV. 2 LOCATIONS

NON-HAZARDOUS DIVISION 2 HAZARDOUS (CLASSIFIED) LOCATIONLOCATION Vmax1 Vmax2 Vmax3 VmaxN

Ci1 Ci2 Ci3 CiNLi1 Li2 Li3 LiN

Imax1 Imax2 Imax3 ImaxN

APPROVEDNONINCENDIVE

SUPPLY

WIRING PER APPLICABLEELECTRICAL CODE

IN NORMAL OPERATION

DEVICES CONTROL THROUGH-CURRENT

4-20mA/HART Vmax 42.4VMaxImum normal 23.5mAoperatIng current Ca 0.012µF La 0µH

ROSEMOUNT 2140 TRANSMITTERS ARE CURRENT CONTROLLERSON INDIVIDUAL PARALLEL BRANCHES WITH RESPECT TO THEPOWER SUPPLY. IN NONINCENDIVE INSTALLATIONS THE ImaxFOR EACH TRANSMITTER IS NOT RELATED TO THE MAXIMUMCURRENT OF THE POWER SUPPLY (Isc) lN THE SAME MANNERAS FOR TRANSMITTER INSTALLED PER I.S. REQUIREMENTS.BECAUSE NONINCENDIVE REQUIREMENTS INCLUDE ONLYNORMAL OPERATING CONDITIONS.IT SHALL BE SUPPLIED BY A CLASS 2 OR LIMITED ENERGYSOURCE IN ACCORDANCE WITH CAN/CSA22.2 No. 61010-1-12

PARAMETERS DEVICEVoc = MInImum of (Vmax1, Vmax2, ...., VmaxN) Imax1 >= Iq1 + Isignal1 Imax2 >= Iq2 + Isignal2 , , , ImaxN >= IqN + IsignalN

Ca <= Ci1 + Ci2 + ... + CiN + CcableLa <= Li1 + Li2 + ... + LiN + Lcable

Imax for an Individual device = Iq + Isignal

Iq = Quiescent current through devlce (Maximum quiescent current for the device)Isignal = Signaling current through device (Protocol may limit signaling to one device at a time)

OperatIng Imax = Iq1 + Iq2 + ... + IqN + Isignal max

Isignal max = Max. of (lsignal1, Isignal2 ..... IsignalN)

D D D D

MECANICALLY PROTECTEDWIRE PER APPLICABLE

ELECTRICAL CODE



1.18 EU Declaration of Conformity

Figure 1-12: EU Declaration of Conformity (Page 1)

EU Declaration of Conformity No: RMD 1110 Rev. AG

ne 3 fo 1 egaP

We,

Rosemount Tank Radar AB Layoutvägen 1 S-435 33 MÖLNLYCKE Sweden

declare under our sole responsibility that the product,

Rosemount™ 2140 Vibrating Fork Liquid Level Detector

manufactured by,

Rosemount Tank Radar AB Layoutvägen 1 S-435 33 MÖLNLYCKE Sweden

to which this declaration relates, is in conformity with the provisions of the European Union

Directives, including the latest amendments, as shown in the attached schedule.

Assumption of conformity is based on the application of the harmonized standards and, when

applicable or required, a European Union notified body certification, as shown in the attached

schedule.

(signature)

Manager Product Approvals (function)

Dajana Prastalo (name)

24-Jun-20;

(date of issue)





ne 3 fo 2 egaP

EMC Directive (2014/30/EU)

Harmonized Standards: EN 61326-1:2013, EN 61326-2-3 :2013

Other Standards Used: EN 61326-3-1:2008

ATEX Directive (2014/34/EU)

Dekra 16ATEX0082X – (Flameproof)

Equipment Group II Category 1/2 G

Ex db IIC T6...T2 Ga/Gb

Harmonized Standards: EN 60079-0:2012+A11:2013, EN 60079-1:2014,

EN 60079-26:2015

Baseefa 16ATEX0136X – (Intrinsic safety)

Equipment Group II Category 1G

Ex ia IIC T5...T2 Ga

Equipment Group II Category 1/2 G

Ex ib IIC T5...T2 Ga/Gb

Harmonized Standards: IEC EN 60079-0:2018, EN 60079-11:2012, EN

60079-26:2015

Baseefa 16ATEX0137X – (Dust Protection by Enclosure)

Equipment Group II Category 1 D

Ex ta IIIC (T92°C…T272°C) (T200100°C…T200280°C) Da

Harmonized Standards: IEC EN 60079-0:2018, EN 60079-31:2014

RoHS Directive (2011/65/EU)

The Model 2140 is in conformity with Directive 2011/65/EU of the European Parliament

and of the Council on the restriction of the use of certain hazardous substances in electrical

and electronic equipment.

(Minor variations in design to suit the application and/or mounting requirements are identified by alpha/numeric

characters where indicated * above)





ne 3 fo 3 egaP

ATEX Directive Notified Body

SGS Fimko Oy [Notified Body Number: 0580]

Takomotie 8

FI-00380, Helsinki

Finland

DEKRA Certification B.V. [Notified Body Number: 0344]

Meander 1051

6825 MJ, Arnhem

Netherlands

ATEX Notified body for Quality Assurance

DNV Nemko Presafe AS [Notified Body Number: 2460]

Veritasveien 1

1322 HØVIK

Norway



1.19 China RoHS

含含有有China RoHS管管控控物物质质超超过过最最大大浓浓度度限限值值的的部部件件型型号号列列表表 Rosemount 2140List of Rosemount 2140 Parts with China RoHS Concentration above MCVs

部部件件名名称称 Part Name

有有害害物物质质 / Hazardous Substances

铅铅 Lead(Pb)

汞汞 Mercury

(Hg)

镉镉 Cadmium

(Cd)

六六价价铬铬 Hexavalent Chromium

(Cr +6)

多多溴溴联联苯苯 Polybrominated

biphenyls(PBB)

多多溴溴联联苯苯醚醚 Polybrominated diphenyl ethers

(PBDE)

电子组件 Electronics Assembly

O O O O O

壳体组件 Housing

Assembly O O O O O

传感器组件Sensor

AssemblyX O O O O

本表格系依据SJ/T11364的规定而制作. This table is proposed in accordance with the provision of SJ/T11364.

O: 意为该部件的所有均质材料中该有害物质的含量均低于GB/T 26572所规定的限量要求.O: Indicate that said hazardous substance in all of the homogeneous materials for this part is below the limit requirement ofGB/T 26572.

X: 意为在该部件所使用的所有均质材料里，至少有一类均质材料中该有害物质的含量高于GB/T 26572所规定的限量要求.X: Indicate that said hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement of GB/T 26572.

O

O

O



*00825-0200-4140*Product Certifications

00825-0200-4140, Rev. AGSeptember 2020

Emerson Automation Solutions6021 Innovation Blvd.Shakopee, MN 55379, USA

+1 800 999 9307 or +1 952 906 8888

+1 952 949 7001

[email protected]

North America Regional OfficeEmerson Automation Solutions8200 Market Blvd.Chanhassen, MN 55317, USA

+1 800 999 9307 or +1 952 906 8888

+1 952 949 7001

[email protected]

Latin America Regional OfficeEmerson Automation Solutions1300 Concord Terrace, Suite 400Sunrise, FL 33323, USA

+1 954 846 5030

+1 954 846 5121

[email protected]

Europe Regional OfficeEmerson Automation Solutions EuropeGmbHNeuhofstrasse 19a P.O. Box 1046CH 6340 BaarSwitzerland

+41 (0) 41 768 6111

+41 (0) 41 768 6300

[email protected]

Asia Pacific Regional OfficeEmerson Automation Solutions1 Pandan CrescentSingapore 128461

+65 6777 8211

+65 6777 0947

[email protected]

Middle East and Africa Regional OfficeEmerson Automation SolutionsEmerson FZE P.O. Box 17033Jebel Ali Free Zone - South 2Dubai, United Arab Emirates

+971 4 8118100

+971 4 8865465

[email protected]

Linkedin.com/company/Emerson-Automation-Solutions

Twitter.com/Rosemount_News

Facebook.com/Rosemount

Youtube.com/user/RosemountMeasurement

©2020 Emerson. All rights reserved.

Emerson Terms and Conditions of Sale areavailable upon request. The Emerson logo is atrademark and service mark of Emerson ElectricCo. Rosemount is a mark of one of the Emersonfamily of companies. All other marks are theproperty of their respective owners.

https://Linkedin.com/company/Emerson-Automation-Solutions

https://Linkedin.com/company/Emerson-Automation-Solutions

https://twitter.com/rosemount_news

https://www.facebook.com/Rosemount/

https://www.youtube.com/user/RosemountMeasurement/

https://www.youtube.com/user/RosemountMeasurement/

product certifications document: rosemount 2140 and 2140:sis … · 2020. 11. 17. · can/csa c22.2...

Documents