YonRui Dash Camera with Rear Camera

Product User Manual

Safe Driving Better LifeRecord Every Moment you want!

Contents1.Product Introduction........................................................................................................ 1

2.Product Structure.............................................................................................................. 2

3.Function Explanation........................................................................................................ 3

4.Operation Guide............................................................................................................. 4~5

5.Dash Cameara Settings................................................................................................ 6~10

6.USB Mode......................................................................................................................... 11

7.Battery Charge Instructions............................................................................................. 11

8.Rear Camera Install Instruction................................................................................. 12~13

9.Troubleshooting Tips and Techniques ..................................................................... 14~15

FAQs................................................................................................................................ 15~16

1.Product Introduction

Install and format the 32GB maximum TF card. Incorrect card installation may damage it or the camera.

The camera will not read card data saved from another device. Formatting willerase all TF card data.

Pay attention to the insert direction of the card. If insert card from the wrong side, it may damage the device and TF card.

Please remove off the car charger lighter with your car when you do not use this dvr device like parking, otherwise your car engine start big instant electricity current probably burn out your dvr device.

This dvr device special use for car, please use it inside car with car charger, if no car charger recharging, its built-in battery very very small, sometimes may cannot be turned on successfully because of no enough electricity.

This device only allow electricity 5V 1A, so please DO NOT use any home charger or USB cable to recharge, you MUST use our original car charger to do recharging,because some home charger adapter have 12V output, it is not suitable, it probably burn out the dvr device. Or sometimes comes out strange squeaky noisy sound because of current not compatible.

In order to use this device correctly more well, Before using the camera read the following:

The dash camera can record video and audio information while you drive. Record scenery on a vacation drive or record an accident or burglary for insurance purposes.

The display can show the front and rear facing video simultaneously. Or, with the rear camera disconnected, only the front camera video will display. With the power cord connected to a 12V outlet, the dash camera automatically records when your vehicle is started or if it is bumped or if motion is detected infront of the lens.

Notice Before Use

1

2.Product Structure

2

3.Function Explanation① Mode Selection KeyPress this key to switch between camera / photo / playback.

② Upward Selection ButtonMenu options, down regulation function keys.

③ OK Key / Power supply keyShort press on / off; Video and photo confirmation button, video mode, press this button to start the video, press the video button again to stop the video; press this button to shoot photos.

④Down select buttonMenu option, down select the function key.

⑤Menu buttonPress this key to call up the menu Menu mode for confirmation.

⑥USB data interfaceUSB data interface, which is used to connect the PC transmission data; II is used to connect the external power supply to the battery charge or provide work power.

⑦Back clip fixation hookFixed video recording instrument.

⑧Rear pull camera interface Connecting with the Rear Camera

⑨RESETRestart recovery hole

⑩SpeakerPlay video or sound amplification hole files, operating sound warning.

⑪LensViewing window.

⑫TF card slotMemory card slot

⑬LCD ScreenImage display，and Video Display.Menu Function Checking

3

4.Operation GuideOK Key / Power supply key :Long press power button around 2~3 seconds to turn on & off.If have TF card inside, once turn on it will enter into recording mode automatically.

Start/Stop recording:In video mode, short press OK button start recording, short press it again, the recording will be stopped.

Photo:In photo mode, short press ① OK Key / Power supply key can take photo

Playback:In playback mode, short press ① OK Key / Power supply key can play the video.

OK button:In video mode/photo mode/playback mode, short press menu button enter into menu, short press up/down to browse, short press ① OK Key / Power supply Button to confirm.

Up button:In menu setting and camera switching mode, it is up function. In standby mode, keep press up button can make motion detection on/off. In playback mode, short press up button can play fast backward

Down button:In menu setting and camera switch mode, it is down function. In video mode, short press down button can make audio on/off.（Notice: the setting will be saved automatically,no need to set once again the next time） In playback mode, short pressdown button can play fast forward

Picture as shown

4

Menu:In standby mode, short press menu button, enter into main menu setting, short press UP/DOWN button, choose the options which you need, short press OK button to confirm. Settings finished, short press Menu button until exit.

1. Browsing files:Press Mode (M) button to switch to playback mode, browse files using UP/DOWN buttons.To play back a file, press OK button.

2. Delete and Protect

In Video mode, in the upper left corner of the screen the icon will be displayed, press OK button to start recording.

In playback mode, press the menu button andselect “Delete, which will delete all files except the protected files.

In playback mode, press the menu button and select Protect. You will have Protect Lock Options and Protect Unlock Options.

REC =icon will appear flashing in the upper left corner.To stop recording press OK button.

Recording video

Playback

5

5.Dash Cameara Settings General settingsDescription:The Following Form ,the first List means Function ,the Second List means Function Explanation,The third list means the Range of choice.In any mode, press

Menu ( ) button twice, to open general settings menu.

LCD Brightnees

TO select duration of LCDBrightness

Select the automatic power off delay time

50 HZ or 60 HZ

Activate/Deactivate buttonpressing sounds

Select the menu displaylanguage

Set date and time

off/30 Second/1 Minute/2 Minutes

Off, 3 Minutes, 5 Minutes, 10 Minutes

(Screen refresh rate)

Browse settings using UP/DOWN buttons and OK button to edit and confirm a setting.

When the Beep Sound off,There is no sound anymore when you pressthe button

Support Chinese English,Japnese,Russian,German,French,Thai,Turkish

Press OK to select the date and time option,short press the OK button and short press the menu key,you can adjust the year/month/day/hour/minute/second,press OK button to confirmthe change

Auto Power Off

Frequency

Beep Sound

Language

Date/Time

6

RedLamp setting

Format

Default setting

Version

Select to revert to factory settings

Select to revert to format SD Card

Select to revert to factory settings

Select to check system firmware version

You can choose Off/On/ Auto ,When you choose Auto,the light would automatic turn on when the environment is dark

Format the memory card (Suggest format the card once about 15 days). When the locked videois too large, you can delete all the videos once. Note: If there are important videos,please use it carefully.

Factory Settings

Firmware version

Video SettingsIn video mode, press Menu ( ) button.

Icon display

7

Resolution Select recording resolution

Cyclic RecordSelect recording split duration,or deactivate the cyclic recording function

Dual CameraSelect to choose record just front Camera or with rear camera together

Interval Record Select the Interval recording time when doing cyclic record

High Dynamic Range Select to revert to factory settings

Exposure

Exposure compensation is an exposure control method, which is generally around ±2-3EV. If the ambient light source is dark, you can increase the exposure value (such as +1EV, +2EV) to highlight the sharpnessof the picture.

1080FHD/ 720P, VGA to Select

Off, 3minutes, 5 Minutes, 10 Minutes

ON/ Off

Off, 100ms, 200ms, 500ms,

On/ off

+3,+2，+1,0，-1，-2，-3

Select Down selection Button ,to find next function

8

Motion Detection

In standby mode,if there is any movement in front of the camera,it will automatically record the whole moving process. The camera will stop recording when there is no more movement.

ON/ Off

RecordingActivate / Deactivate Recording voice ,if this function is on ,only record voice

ON/ Off

Date Stamp Activate / Deactivate date stamp on the recording

ON/ Off

Gravity Sensing Adjust sensitivity level for the gravity sensor

Off, Low,Medium, High

Parking Guard

Its used for automatic power onand recording when the car is stalled and vibrates.The parking monitor can be used when the battery has enough power or connect to the car battery.

ON/ Off

Photo SettingsIn photo mode,press Mode button and press Menu( )button.

9

Capture Mode Adjust Photo Capture Intervals Time Single Shot, 2s Delay, 5s Delay,10s Delay

Resolution Adjust photo resolution VGA,1.3M,2M,3M,5M,8M,10M

Continuous shooting

Activate / Deactivate Continuous shooting function On/ Off

Quality Adjust Photo Quality Fine /Normal /Economy

Sharpness Adjust sharpness level Strong ,Normal,Soft

White Balance Adjust the white balance according tothe environment

Auto,Daylight,Cloudy,Tungsten,Fluorescent

10

7.Battery Charge InstructionsThere are three ways to charge the battery, the red indicator will light up in the charging process, the entire charging process time is about 180 minutes, the red indicator will be automatically off when fully charged.

Please NOTE: When improper using this product and make the camera crash, you canuse a pin to press the Reset button and then reboot the dash cam.

1. Charging via the power adapter

2. Charging via PC-USB

3. Charging via car power supply

6.USB Mode(The USB connection cable need to buy separately):Connect the USB cable to the computer, pressing the power button, the car camerarecorder will automatically pop up the USB menu. There are two different modes to choose as below:

1) USB ModeIn this mode, you can save and read video files or photo files.

2) PC CameraConnect USB data cable (this kind of cable is another purchase).Selecting this mode will pop up USB video device, you can take photos in real time or have video chat.

11

8.Rear Camera Install Instruction

A:Install inside back windowB:Install outside back plateRear Camera Installation Steps

Step 1 : Turn off dvr camera monitor,plugback camera into device av-out.

Step 2 : Open the above and side gap a little then Insert the cable into.

Step 3: Keep wiring surrounding the inside gap till to the car back.

Step 4: You can stick the back camera inside of the car back window.

Reverse Back Light Power

A

B

12

Step 5 : Also you can fix the back camera on the above of the car back plate

Step 6 : Connect the back camera jack plug into cable socket.

Step 7: Connect the wire with car reverseback light power red to positive.

The Rear camera ,normally is for the Reversing,so the picture would be mirror display.The Picture would be opposite ,so it would be easy for you when you reversing.

Attention:

Step 8: Fix extra cables into automotiveinterior gap.

13

If there is any problem on the product in normal use, please refer to these troubleshooting step to resolve the problem as below

9.Troubleshooting Tips and Techniques

Can not take pictures or record video:Check the TF card storage or if its locked.

The dash cam will automatically stop when recording:Because the high-definition video file is huge,please use high-speed TF card that compatible with SDHC. High-speed TF card has C4 or C6 logo.

A "file error" notice appears when playback your pictures and videos:An error occurred while storing data of TF card and caused that the file incomplete.Please use the "Format" function to reformat the TF card.

Video quality is not clear:Please check the lens has any dirt or finger print and use lens paper to wipe the lensbefore shooting.

Our back camera is a digital camera. It is more stable than ordinary back camera. Therefore, when operating, it must be strictly operated by thefollowing steps.

1.Connect the back camera to the drive recorder device

2.Connect the car charger to the drive recorder device.

3.Start the car engine, then plug the car charger to the car cigar socket, the drive recorder will power on automatically.

4.When you reverse your car, the back camera will display the car back image automatically.

Attention: The back camera adopts digital technology, it must be connected to the car charger recharging when be used. Otherwise, the back camera may not be able to operate properly. Please be careful.If you need any further assistant ,pls feel free to contact the YonRui Customer Service Team.We will try our utmost to solve the problems which you meet.Email: customerservice@yonruicn.comFacebook Page: @yonrui001 YonRui Customer Service

Notice Before Use

14

FAQs:Q: Why my dvr camera indicate “SD card Full”?

A: 1) Please check if your memory card is original brand high speed Class 10 memory card, if you use some copy card like Class 4 or Class 6, it will indicate SD card full” because it is not compatible. (Note please: DVR max support only 32GB card only)

Crash:You can use a pin to press the Reset button and then reboot the dash cam.

When shooting the sky,water and other scenes, the image is very dark:In the contrast scenario,the automatic exposure feature of the camera cam be affectedwhich can be modified by adjusting the values of “Exposure” in the setting menu.

On cloudy days and indoor lighting, the color is not perfect:Please check the white balance if auto.

There’s horizontal stripe interference in pictures:This is caused by wrong light source frequency,please set the frequency 50 Hz or 60 Hz according to the local power supply.

3) Please check your dvr MENU settings if you have turn OFF G-Sensor, Parking Monitor & Motion Detect this 3 functions already at the same time? If G-Sensor is on, the file will be protected to lock that can not be overwrite, also dvr will auto go to recording all the time if Parking Monitor & Motion Detect is on, so the SD card will be full.

4) You must format to clear up your memory card file by hand at least 2~3 times within a month because the memory card inside will have some locked file that happen while driving at some emergency time, but this locked files can not be overwrite automatically. You must delete them by hand.

2) Please check your dvr MENU settings if you have opened on Loop Recording this function already? You must open ON Loop Recording this function the previous video can be overwriting.

15

Q: Why my dvr camera auto on & off continuously?

A: Please check first if your dvr MENU settings open on Parking Monitor and G-Sensor this 2 function already? Normally if Parking Monitor is on the dvr will goto Parking Monitor mode, in this mode status, dvr will auto on once detect any touch or shake, then if will auto off if while no touch. So it will auto on & off continuously.G-Sensor this function also will lock this status video file to avoid no overwrites then it can keep as parking evidence. Please turn off this 2 function in MENU settings then try again.At the same time, please turn off Motion Detect this function in MENU settings also, because if Motion Detect is on, it will auto go to recording once have any movement in front.

Q: Why my dvr always freeze while recording?

A: Please check if your memory card is original brand high speed Class 10 memory card, if you use some copy card like Class 4 or Class 6, it will indicate SD card fullor error because it is not compatible will happen freeze while recording.So if your camera happen freeze problem, please try to use another different new original class 10 memory card to have a try, then you can identify the problem reason. If change a new card still can not be ok, that maybe the dvr camerafirmware problem, please contact seller to upgrade firmware.

Q: Why my dvr camera recording image not clear?

Note: we reserve the modification right of the device design and specifications without notice

A: Please check the video link that we upload online website link already, it is real link, so its recording quality image exactly same as product. In dvr camera MENU settings normally have 1080P, 720P, VGA option.

Highest quality image is 1080P, middle quality image is 720P, and lowest quality image is VGA. Please set as highest resolution 1080P when you do recording.If you set resolution as VGA, video image quality will be not clear, please change to 1080P option in settings.

Besides, video quality image sometimes will be not so good if the surroundings not so good like at night or fog days.

16