*

*

*

**

Underwater

30 meter +

Max 2 ,000

6,500

90 degrees

The Great Dunton Forge, London RoadDunton Green, Sevenoaks, Kent TN13 2TD UK

T: +44 (0) 1732 455753 F: +44 (0) 1732 743233E: uwl@underwaterlights.com

VAT NO: 556 4425 31 Registered in England No: 2348038

© 201 Underwater Lights Limited All Rights Reserved.

Underwater lights limited reserves the right to change specifications without notice.

Your Local Dealer

QT- QT- RGB WTechnical

Lumens ,000

Kelvin

Typical LED Life Expectancy 40,000 hrs

Min-Max Operating Voltage 110 - 240V AC

Current / Amp draw 1.4 - 0.7 amps

Driver Type External

Driver Output 4 channel @ 36V

Control Options

6,500

40,000 hrs

110 - 240V AC

- 0. amps

External

@

On / Off Switch DMX

Physical

Removal Space Required

Total weight

Driver Dimensions (L x W x H)

Cable Length

1 mm

13 lbs

8.7” x 4.7” x 3.5”

(220 x 120 x 90mm)

10 feet - 3 meters

1 mm

1 lbs

10.2” x 6.3” x 3.5”

(260 x 160 x 90mm)

10 feet - meters’

-

Colo r Par Number

RGB+W

QT- W

QT- B

QT- RGB W

QT-

QT-

QT- W

Bulleyts 316L Stainless Steel

1: Projector cable S001112: Projector lid complete S00C1023: "O" Ring 001084: Projector case 001015: Lamp (150w HQI) 910046: Reflector 917917: Connecting ring 000C038: Gaskets 000C079: S.S. M6 socket screws 9330610: Glass retaining ring 000C0411: Gaskets 000C0212: Glass 000C0113: Electronic ballast-120v S00801-12013: Electronic ballast-230v S00801-230

Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit

the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm “Allen key” making sure the glass retaining ring is square. Torque the screws to Nm ( ft/lbs)

the sequence shown, check the ring again and re-torque the screws again to the same setting.

ORDERING NUMBER FOR 120 VOLT AND 230 VOLT MODELS A00310-120, A00324-120, A00338-120, A00350-120A00310-230, A00324-230, A00338-230, A00350-230

FLUSH - A00310

0-24 DEGREE - A00324

24-38 DEGREE - A00338

50 DEGREE - A00350

1

2

3

4 5

6

Cable specification from electronic ballast to projector (Pt.No. S00111)Shielded 3 core, Temperature -60C to +180C, Voltage 2000 volts. Maximum distance between ballast and projector with the shield earthed 20 meters.120 volt 150 watt ballast - running current 1.5 amps230 volt 150 watt ballast - running current 0.75 amps

Lamp (150w HQI) 91004Glass with gaskets S00C01-2Electronic ballast-120v S00801-120Electronic ballast-230v S00801-230

The Bulleyt is serviced from inside the hull. Allow access for maintenance and space for ventilation.Do not use the Bulleyt in dry-dock or out of the water.Allow a minimum of 70mm behind the projector lid (item 2) for lamp replacements.

Do not attempt to remove the glass lens while afloat.The projector must be correctly assembled with lidand secured to the Bulleyt whilst afloat.

ELECTRONIC BALLAST COMPLETEWITH ALUMINIUM ENCLOSURE -S00800-120 OR 230

PLEASE REGISTER YOUR PRODUCT WARRANTEE DIRECT TO FOR TECHNICAL INFORMATION PLEASE EMAIL

SALES, PRODUCT INFORMATION AND NEWS GO TO

UL Ti MATE 70 316L Stainless Steel

1: Projector cable S001112: Projector lid complete S00C1023: "O" Ring 001084: Projector case 001015: Lamp (150w HQI) 912056: Reflector 91791-1A7: Connecting ring 000C038: Gaskets 000C079: S.S. M6 socket screws 9333410: Glass retaining ring 00304-70A11: Gaskets 00278-A12: Glass 00280-70A13:Electronic ballast-100/277v S00800-V1W2

Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm Allen key making sure the glass retaining ring is square. Torque the screws to Nm ( . ft/lbs) in the sequence shown, check the ring again and re-torque the screws again to the same setting.

ORDERING NUMBERS FOR 100-277 VOLT 150 WATT LIGHTS FLUSH - S00310-70A-V1, 20 DEGREE - S00320-70A-V1,

24-38 DEGREE - S00338-70A-V1, 50 DEGREE - S00350-70A-V1

FLUSH - S00310-70A

20 DEGREE - S00320-70A

24-38 DEGREE - S00338-70A

50 DEGREE - S00350-70A

1

2

3

4 5

6

Cable specification from electronic ballast to projector (Pt.No. S00111)Shielded 3 core, Temperature -60C to +180C, Voltage 2000 volts.Maximum distance between ballast and projector with the shield earthed 10 meters.Ballast power 100/277 volt 150 watt ballast - running current 2.0/07.ABallast will not ignite a hot lamp. The ballast has a cycle of three atempts to ignite the lamp then will wait for fourminutes before repeating the cycle.

Lamp (150w HQI) 91205Glass with gaskets S00C01-70AElectronic ballast 95322

The UL Ti MATE is serviced from inside the hull. Allow access for maintenance and space for ventilation.Do not use the UL Ti MATE in dry-dock or out of the waterAllow a minimum of 70mm behind the projector lid (item 2) for lamp replacements.UL Ti MATE to be fitted 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard.

Do not attempt to remove the glass lens while afloat.The projector must be correctly assembled with lid secured to the UL Ti MATE 70 whilst afloat.

ELECTRONIC BALLAST COMPLETE WITH IP65ENCLOSURE -S00800-V1W2 (V1=100-277 VOLTS, W2=150 WATTS)

PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO FOR TECHNICAL INFORMATION PLEASE EMAIL

SALES, PRODUCT INFORMATION AND NEWS GO TO Ul ti mate 70 SS

‘submersible through hull light’

UL Ti MATE 75-SA-ICE-SS-H-14-10-2011

FLUSH

‘submersible through hull light’

UL Ti MATE 75-SA-ALU-H-14-10-2011