L3 Managed Ethernet Switch

GS-5220 Switch Series

Quick Installation Guide

Table of Contents

1. Package Contents ....................................................................................... 3

2. Requirements ............................................................................................. 5

3. Terminal Setup ........................................................................................... 6

3.1 Logging on to Console ......................................................................... 7

3.2 ConfiguringIPAddress ......................................................................... 7

3.3 StoringCurrentSwitchConfiguration ..................................................... 9

4. Starting Web Management .........................................................................10

4.1 LoggingintotheManagedSwitch .......................................................10

4.2. SavingConfigurationviaWeb ..............................................................13

5. RecoveringBacktoDefaultConfiguration .....................................................14

6. Customer Support .....................................................................................15

3

1. Package ContentsThank you for purchasing PLANET GS-5220 L3 Managed Ethernet Switch series.Thedescriptionsofthisseriesareshownbelow:

ModelNameGigabitRJ45 Ports

GigabitSFPSlots

10GSFP+ Slots

PoEPowerBudget

RedundantPower System

GS-5220-16T4S2X 16 4 2 - -

GS-5220-16T4S2XR 16 4 2 - Yes

GS-5220-20T4C4X 24 4 combo 4 - -

GS-5220-20T4C4XR 24 4 combo 4 - Yes

GS-5220-24P4X 24 4 combo 4 400W -

GS-5220-24P4XR 24 4 combo 4 400W Yes

GS-5220-24PL4X 24 4 combo 4 600W -

GS-5220-24PL4XR 24 4 combo 4 600W Yes

GS-5220-48P4X 48 - 4 400W -

GS-5220-48PL4XR 48 - 4 720W Yes

“Managed Switch” is used as an alternative name in this Quick InstallationGuide.

4

Open the box of the Managed Switch and carefully unpack it. The box shouldcontainthefollowingitems:

z TheManagedSwitch

z QuickInstallationGuide

z RJ45 to RS232 Cable

z Rubber Feet

z TwoRack-mountingBracketswithAttachmentScrews

z PowerCord

z SFPDust-proofCaps

Model SFPDust-proofCaps

GS-5220-16T4S2X 6

GS-5220-16T4S2XR 6

GS-5220-20T4C4X 8

GS-5220-20T4C4XR 8

GS-5220-24P4X 8

GS-5220-24P4XR 8

GS-5220-24PL4X 8

GS-5220-24PL4XR 8

GS-5220-48P4X 4

GS-5220-48PL4XR 4

If any item is found missing or damaged, please contact your local reseller forreplacement.

5

2. Requirements z Workstations runningWindows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.

z WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)

z Serial Port Connection(Terminal)

The above Workstations come with COM Port (DB9) or USB-to-RS232converter.

TheaboveWorkstationshavebeeninstalledwithterminal emulator,suchasHyperTerminalincludedinWindowsXP/2003.

Serial cable -- one end is attached to theRS232 serial port,while the otherendtotheconsoleportoftheManagedSwitch.

z Ethernet Port Connection

Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.

The above PC is installed with Web browser and JAVA runtime environmentplug-in.

Note

It isrecommendedtouseInternetExplorer8.0orabovetoaccessthe Managed Switch. If theWeb interface of the Managed Switchis not accessible, please turn off the anti-virus software or firewallandthentryitagain.

6

3. Terminal SetupTo configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial port of the Managed Switch.

Managed Switch

PC / Workstationwith

Terminal Emulation Software

Serial Port

RS232 to RJ45 Cable

Console PortRJ45

Figure 3-1 Managed Switch Console Connectivity

A terminal program is required tomake the software connection to the ManagedSwitch.

1. 1. Run terminal program on the OS.

2.When the following screen appears, make sure that the COM port should beconfiguredas:

Baud:115200

Databits:8

Parity:None

Stopbits:1

Flowcontrol:None

Figure 3-2 COM Port Configuration

7

3.1 Logging on to ConsoleOnce the terminal is connected to the device, power on theManaged Switch andtheterminalwilldisplay“runningtestingprocedures”.

Then, the followingmessage asks to log in user nameandpassword. The factorydefault user name and password are shown as follows and the login screen inFigure3-3appears.

Username:adminPassword:admin

Figure 3-3: Managed Switch Console Login Screen

TheusercannowentercommandstomanagetheManagedSwitch.Foradetaileddescriptionofthecommands,pleaserefertothefollowingchapters.

Note

1.Forsecurity reason,pleasechangeandmemorize thenewpass-wordafterthisfirstsetup.

2.Only accept command in lowercase letter under console inter-face.

3.2 ConfiguringIPAddressTheManagedSwitchisshippedwithdefaultIPaddressshownbelow.

IPAddress:192.168.0.100SubnetMask:255.255.255.0

TocheckthecurrentIPaddressormodifyanewIPaddressfortheSwitch,pleaseusetheproceduresasfollows:

8

ShowthecurrentIPAddress1.Atthe“#”prompt,enter“show ip interface brief”.

GS-5220Series#show ip interface brief

2.ThescreendisplaysthecurrentIPaddressasshowninFigure3-4.

Figure 3-4: IP Information Screen

ConfiguringIPAddress3.At the “#”prompt,enter the followingcommandandpress<Enter> as shown inFigure3-5.

GS-5220Series# configure terminalGS-5220Series(config)# interface vlan 1GS-5220Series(config-if-vlan)# ip address 192.168.1.100 255.255.255.0

ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.

IPAddress:192.168.1.100SubnetMask:255.255.255.0

Figure 3-5: Configuring IP Address Screen

4.Repeatstep1tocheckiftheIPaddresshaschanged.

9

3.3 StoringCurrentSwitchConfigurationAtthe“#”prompt,enterthefollowingcommandandpress<Enter>.

# copy running-config startup-config

Figure 3-6: Saving Current Configuration Command Screen

If the IP is successfully configured, the Managed Switch will apply the new IPaddress setting immediately. You can access the Web interface of the ManagedSwitchthroughthenewIPaddress.

Note

If you are not familiar with the console command or the relatedparameter,enter“help”anytimeinconsoletogetthehelpdescrip-tion.

10

4. Starting Web ManagementThe following shows how to start up the Web Management of the ManagedSwitch. Note the Managed Switch is configured through an Ethernet connection.Please make sure the manager PC must be set to the same IP subnet address.

For example, the default IP address of the Managed Switch is 192.168.0.100,then the manager PC should be set to 192.168.0.x (where x is a numberbetween1and254,except100),andthedefaultsubnetmaskis255.255.255.0.

PC / Workstationwith Web Browser

192.168.0.x

Managed Switch

RJ45/UTP Cable

IP Address:192.168.0.100

Figure 4-1: IP Management Diagram

4.1 Logging in to the Managed Switch1.Use Internet Explorer 8.0 or above Web browser and enter IP address

http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhavejustchangedinconsole)toaccesstheWebinterface.

2.When the followingdialogboxappears,pleaseenter thedefaultusernameandpassword“admin” (or the password youhave changed via console). The loginscreeninFigure4-2appears.

11

DefaultIPAddress:192.168.0.100DefaultUsername:adminDefaultPassword:admin

Figure 4-2: Login Screen

3.Aterenteringthepassword,themainscreenappearsasFigure4-3shows.

Figure 4-3: Web Main Screen of Managed Switch

12

The Switch Menu on the top and left of the Web page lets you access all thecommandsandstatisticstheManagedSwitchprovides.

Figure 4-4: Switch Menu

Note

Ifyouarenot familiarwithSwitch functionsor the relatedparam-eter,press“Help icon” anytime on the Web page to get the help description.

Now, you can use the Web management interface to continue the Switchmanagement or manage the Switch by console interface.

Please refer to the user’s manual for more.

13

4.2.SavingConfigurationviaWebTo save all applied changes and set the current configuration as a startupconfiguration, the startup-configuration file will be loaded automatically across asystem reboot.

1. Click the Save icon on the top Switch Menu bar.

Figure 4-5: Save Config -- Hot key

2. Press the “Save Configuration” button.

3. Or the other way to save the setting is to click Maintenance and thenSave Startup Config.

14

5.RecoveringBacktoDefaultConfiguration IPaddresshasbeenchangedoradminpasswordhasbeenforgotten–To reset the IP address to the default IP addres “192.168.0.100” or reset the login password to default value, press the hardware-based reset button on the rear panel for about 10 seconds. After the device is rebooted, you can log in tothemanagementWebinterfacewithinthesamesubnetof192.168.0.xx.

10

9

2

1

4

3

6

5

8

7115200, N, 8, 1

Console

GS-5220-20T4C4X

SYS

AC

Reset

2 6 10 14 18 224 8 12 16 20 24

1 5 9 13 17 213 7 11 15 19 23

ACT1000 ACT10/100

FANAlert

10

9

12

11

2

1

4

3

6

5

8

7SYS

PWR

Ring

115200, N, 8, 1

Console

Reset

2 64 8

1 53 7

10 1412 16

9 1311 15

18 2220 24

17 2119 23

GS-5220-24PL4X

ACTLNK1000ACTLNK10/100 PoE-in-Use

PoE

Figure 5-1: GS-5220-20T4C4X(R)/GS-5220-24PL4X(R) Reset Button

SYS

AC

DC

Ring

Reset115200, N, 8, 1

Console

2

1

4

3

6

5

8

7

10

9

12

11

14

13

16

15

18

17

20

19

22

21

ACT1000 LNKACT10/100 LNK

PoE-in-Use

Figure 5-2: GS-5220-48PL4X(R) Reset Button

15

6. Customer SupportThank you for purchasing PLANET products. You can browse our online FAQresourceandUser’sManualonPLANETWebsitefirsttocheckifitcouldsolveyourissue.Ifyouneedmoresupportinformation,pleasecontactPLANETswitchsupportteam.

PLANETonlineFAQs:http://www.planet.com.tw/en/support/faq

Switchsupportteammailaddress:support@planet.com.tw

GS-5220SeriesUser’sManual:http://www.planet.com.tw/en/support/downloads?method=category&c1=&p=&type=3

(Please select your switch model name from the drop-down menu of ProductModel.)

Copyright © PLANET Technology Corp. 2020.Contents are subject to revision without prior notice.PLANET is a registered trademark of PLANET Technology Corp.All other trademarks belong to their respective owners.