320 East Harvard Street, Glendale, CA 91205 P 818.246.3112 F 818.246.3567 www.osborn320.com320 East Harvard Street, Glendale, CA 91205 P 818.246.3112 F 818.246.3567 www.osborn320.com

DELIVERY BY

HAND

OVERNIGHT

MAIL

MESSENGER

OTHER

DATE

TO

AdDRESS

CC

FROM

NOTE

APPROVALSENT FOR

QUANTITY

DISTRIBUTION COMMENT INFORMATION

DESCRIPTION

DRAWINGS SAMPLES SPEC . SHOP DRAWINGS OTHER

#

TRANSMITTAL

A 1 1 0 4 9

07.18.16

Tony Barrios / GUSD

Dawn Brisco, Annette Wu, Brad Brewer

Teagan Castellon

Jefferson ES - ORG Classroom Building

Submittal # 093000­01­0­Tiling

Digital Note Markings

1. Color pending approval from District,

2. Provide Product data verifying compliance with CHPS EQ2.2.1 for adhesive and sealants. see Spec 09300­2/C & F.

Reset

Reset

Reset

NO EXCEPTION TAKEN REJECTED NOTE MARKINGS REVISE AND RESUBMIT

Review is for general conformance with the design concept and Contract Documents. If any deviations from the Contract Documents are included herein, such deviations shall be presumed by the Contractor as not having been reviewed, except where specific attention is called to the change as a deviation. Markings or comments shall not be construed as relieving the Contractor from compliance with the project plans and specifications. The Contractor is responsible for details and accuracy; confirming and correlating all quantities and dimensions; fabrication processes and techniques of construction; coordination of this work with that of all other trades and the satisfactory performance of this work

.

By tcastellon

3:59 pm, Jul 18, 2016

Planning, Development & Facilities 349 Magnolia Avenue

Glendale, California 91204 Tel: 818.507.0201 Fax: 818.507.4911

Project Name: Jefferson ES-12 Classroom BldgDSA No:

District PO No: District Contract No: 113-15/16

TRANSMITTAL

To: Tony Barrios

From: Chalmers Construction Services Inc.

TR No.

Date:

We are Send ing You: V ia : These a re Transmi t ted as Checked Be low:

Subm i t t a l s eM a i l F o r App r ov a l No E x c ep t i on s T ak en

P r i n t s M a i l F o r You r U s e M ake Co r r e c t i on s N o t ed

T r a c i ng s M es s enge r A s R eques t ed R ev i s e and R e subm i t

S p ec i f i c a t i on s Hand Fo r R ev i ew & C ommen t R e j e c t ed

S amp l e s Sp ec i a l D e l i v e r y U se / D i s t r i b u t i on O t he r

Cop y o f L e t t e r F a x F o r You r I n f o r ma t i on

Change O rd e r

O t he r

Copies Date Doc. No.

Description

Remarks:

Issued By: Ara Baghdasarians

Copies To:

A#:03-114361 , File#:19-41

57

07/13/16

1 07/13/16 Submittal #57 (093000)

Lic# 665139

TRANSMITTAL

DATE: 7/6/2016

CONTRACTOR: Chalmers Construction

2600 Foothill Blvd STE 304

La Crescenta CA 91214

PROJECT: Jefferson ES

SECTIONS: 93000

Item No. Qty. Size Description AREA

93000-4 2.02 Product Data Plaster Sand

93000-4 2.02 Product Data Portland Cement Thick Set

93000-4 2.02 Product Data Hydrated Lime Thick Set

93000-5 2.02 Product Data Custom Building Products - Versabond Thinset Floor & Wall Thinset

93000-5 2.02.J Product Data Red Gard Waterproof Membrane

93000-5 2.02.K Product Data 2x2 Wire Mesh Reinforcing Wire

93000-5 2.02.L Product Data Polyblend Sanded & Unsanded Grout All Grouts

93000-6 2.02.Q Product Data AquaMix Penetrating Sealer All tile & grouts

93000-6 2.02.R Product Data Laticrete Latasil NS Sealant

93000-6 2.03.A 2x2 Daltile Keystones Floor Tile

93000-6 2.03.B 4x4 Daltile Semi-Gloss Wall Tile

SUBMITTED BY: Jessie Zaragoza

Submittal No.1

9713 Orange Ter. Pico Rivera, CA 90660 Office: 562-942-0519 Fax: 562-949-1976

colors TBD, pendingdistrict approval

Manufacturer’s CertificationWe herby certify that this Type I/II/V Low Alkali cement sourced from US CA Mojave supplied to you has been manufactured in accordance with and

9350 OAK CREEK ROAD, MOJAVE, CALIFORNIA 93501 / TEL (661) 832 3700, FAX (661) 824-4908

Report Date: 11/20/2013

TYPE I TYPE II TYPE V MOJAVE

Requirements Requirements Requirements TYPE II/V

Limestone Analysis

We herby certify that this Type I/II/V Low Alkali cement, sourced from US, CA, Mojave, supplied to you has been manufactured in accordance with andmeets the standard requirements of ASTM C150 specification for Type I, Type II and Type V cement. Below are the average chemical and physical data from October 7, 2013 to October 31, 2013

ASTM C150 RequirementsChemical Analysis Additional Data

y

Silicon dioxide (SiO2), min,% --- --- --- 20.1 1.6Aluminum oxide (Al2O3), max,% --- 6 --- 3.4 0.8Ferric oxide (Fe2O3), max,% (Note 2) --- 6 --- 3.8 0.3Calcium Oxide (CaO), % 63.4Magnesium oxide (MgO), max,% 6.0 6 6 2.6 2.3Sulfur trioxide (SO3), max,%; (Note 1) 3.0 3 2.3 2.8 0.2Loss on ignition, max,% 3.0 3.0 3.0 2.7Insoluble residue, max,% 0.75 0.75 0.75 0.60 Base Cement Phase

MO T IAlkalies(Na2O+0.658*K2O), max,% 0.6 0.6 0.6 0.57 Composition

Tricalcium silicate (C3S), % --- --- --- 58 61Dicalcium silicate (C2S), % --- --- --- 13 14Tricalcium aluminate (C3A), max,%; (Note 2) --- 8 5 2 3Tetracalcium aluminoferrite (C4AF),% --- --- --- 12 12C4AF + 2*(C3A), max,%; (Note 2) --- --- 25 17CO2, % --- --- --- 1.4limestone, max,% 5 5 5 3.4C CO3 i li t i % 70 70 70 95 9

OJ A

TY P

I II

CaCO3 in limestone, min, % 70 70 70 95.9

Physical DataAir content of mortar,max,% 12 12 12 7Passing 45um (no. 325) sieve, % --- --- --- 98.2Blaine Fineness, min, m2/kg; 260/--- 280/--- 280/--- 450Heat of Hydration, C186, (cal/g), (Note 3) --- --- --- 77Autoclave expansion, max,% 0.80 0.8 0.8 0.01Compressive Strength, min, MPa, (psi)3 d M 12 0 10 8 26 4

AV E

PE

II V

3 days , Mpa 12.0 10 8 26.4 PSI 1740 1450 1160 38307 days , Mpa 19.0 17 15 33.4 PSI 2760 2470 2180 485028 days *(from previous month) , Mpa --- --- 21 39.8 PSI --- --- 3050 5770Vicat, initial set, min.-max., minutes 45-375 45-375 45-375 131C 1038, 14 day max, % expansion (Note 1) 0.020 0.020 0.020 0.015C 452 14 day max % expansion (Note 2) 0 040 0 034

E C 452, 14 day max, % expansion (Note 2) --- --- 0.040 0.034False Set, final penetration, min,% 50 50 50 79

Apparatus and methods used in this laboratory have been checked by the Cement and Concrete Reference Laboratory of the National Institute of Standards andTechnology. A copy of the report detailing their findings is available upon request. Major Oxides are analyzed by X-ray Fluorescence Spectrometry.

Note 1: ASTM C150, Table 1, Note D, It is permissible to exceed the values in the table for SO3 content, provided it has been demonstrated by Test Method C1038 that thecement with the increased SO3 will not develop expansion exceeding 0.020% at 14 days..Note 2: ASTM C150, Table 1, Note B, Does not apply when the optional sulfate resistance limit in Table 4 is specified. Note 3: ASTM C150, Table 1, Note H: For Informational Purposes Only

Charles T. Wright Jr.-Quality Control Superintenden

Chemstar Type S LimeIt’s the Choice of Architects, Specifiers, Engineers, Contractors and Masons,for a High Performance, Cost Effective Mortar.

In independent university and Brick Industry of America studies, cement-

lime mortars consistently outperformed ASTM C270 mortar

cement and masonry cement types by a significant margin.

Compared to the other mortar types and mortars made

with clay and air entraining agents, cement-lime

mortar with Chemstar Type S lime delivered:

• Two to four times the flexural bond strength

• 20-40 times better resistance to water penetration

• 2-3 times the boardlife

• Excellent compatibility with all types of clay bricksand concrete masonry units

• Superior compatibility with white cement reducingflash setting

When it comes to workability, boardlife, and sand carrying capacity,nothing is better than a cement-lime mortar with Chemstar Type Slime. And nothing enhances the quality and productivity of yourmasonry project like Chemstar Type S lime. By specifying ChemstarType S lime, you are providing your customers with the best flexuralbond strength and resistance to water penetration available. No wonder it is the market leader.

Chemstar sets the standardWhile cement-lime mortar is superior to other compositions, mortarmade with Chemstar Type S lime is clearly a cut above the rest.Produced from the calcination of high quality dolomite andsubsequent pressure hydration of the resulting quicklime, ChemstarType S lime meets or exceeds all applicable standards, including:

• ASTM C 207• ASTM C 206 (Henderson and New Braunfels production)• Uniform Building Code (UBC) standard 21-13• International Building Code (IBC) 2000, 2103.7

As a result of their very small size (1/100th of a micron) the Chemstar Type S lime particles have very special properties whichyield the following, significant benefits:

• Prolonged cement hydration for increased boardlife• Excellent water retention• Use of marginal mortar sand, as every grain is fully coated• Maximum sand yield• Superior workability• Improved mortar consistency due to high dispersing properties.

Chemstar meets the codeBuilding codes, including IBC and UBC standards, recognize theflexural bond strength of cement-lime mortars. Unreinforced masonrywalls built using cement-lime mortars are allowed by code toaccommodate a lateral load (i.e., seismic or wind driven) 67% greaterthan either masonry cement or mortar cement. In fact, masonry cementis not even allowed in seismic zones because of its deficiencies in bondstrength. Chemstar Type S lime goes a step further by helping to knitthe mortar to the masonry unit surface. This enhances the bond andpromotes the early hydration of the cement, assuring full developmentof mortar strength during the first few critical days.

C h e m s t a r Ty p e S L i m e . . . i t b e l o n g s i n y o u r m o r t a r

© 2001 Chemical Lime Company. All rights reserved. Information and specificationssubject to change. Chemstar and Chemstar Type S lime are trademarks of Chemical Lime Company.

C a l l 8 0 0 . 3 6 5 . 6 7 2 4

F a x 8 1 7 . 7 3 2 . 8 5 6 4

Vi s i t w w w. c h e m i c a l l i m e . c o m

Wr i t e P O B ox 9 8 5 0 0 4F o r t Wo r t h , Te xa s 7 6 1 8 5 . 5 0 0 4

Chemical Lime Company, North America’s

leading producer and supplier of lime for

building construction, supports your business

with an expert team of technical and

application specialists. Their function is to

work with you, ensuring you achieve the best

possible results from product development to

mortar testing and analysis. Our production

facilities in Nevada, Texas, and Utah supply

Chemstar Type S lime to knowledgeable

building material dealers across the country.

Chemstar Type SA hydrated lime is

manufactured at our facility in Texas and is

available throughout that market.

Headquartered in Fort Worth, Texas,

Chemical Lime Company serves a variety of

industrial markets from 55 locations in North

America. Chemical Lime Company is a

member of the Lhoist Group headquartered

in Brussels, Belgium.

Safety information is contained in Material Safety

Data Sheets (MSDS) available from your supplier

or directly from Chemical Lime Company by fax

or our website.

Type S Hydrated Lime – May 1, 2015

SAFETY DATA SHEET

SECTION 1 IDENTIFICATION Product

Name: Type S Hydrated Lime

Other Names: Dolomitic Hydrate; Hydrated Dolomitic Lime; Calcium Magnesium Hydroxide; Double Hydrated Dolomitic Lime

Recommended Uses: Construction; pH adjustment; Water Treatment; FGT;

Company Identification:

US Operations: Canadian Operations:

Lhoist North America, Inc. Lhoist North America of Canada, Inc. 3700 Hulen Street 20303-102B Ave. Fort Worth, TX 76107 Langley, BC V1M 3H1 817-732-8164 604-888-4333

Emergency Phone Number:

Chemtrec 1-800-424-9300

SECTION 2 HAZARDS(S) IDENTIFICATION Classification Eye Damage – Category 1

Carcinogen – Category 1

Skin Irritation – Category 2

Specific Target Organ Toxicity Single Exposure – Category 3 (Respiratory System)

Specific Target Organ Toxicity Repeat Exposure – Category 1 (Respiratory System)

Labeling:

Pictograms:

Signal Word(s): Danger

Type S Hydrated Lime – May 1, 2015

Hazard Statements: Causes serious eye damage.

Causes skin irritation.

May cause respiratory irritation.

Causes damage to lungs through prolonged or repeated exposure when inhaled.

May cause cancer through inhalation.

Precautionary Statements:

Wear protective gloves and eye protection. Wash exposed skin thoroughly after handling. Do not breathe dust. Use only outdoors or in a well-ventilated area. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not eat, drink or smoke when using this product.

If on skin: wash exposed skin with plenty of water. If skin irritation occurs: Get medical attention. Take off contaminated clothing and wash it before reuse.

If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Seek medical attention immediately. If inhaled: Remove person to fresh air and keep comfortable for breathing. Seek medical attention if you feel unwell.

If exposed or concerned: Get medical advice

Dispose of contents or containers in accordance with applicable regulations.

Other Hazards: None.

SECTION 3 COMPOSITION/ INFORMATION ON INGREDIENTS

Chemical Name: Calcium Magnesium hydroxide

Common names and synonyms: Dolomitic Hydrate; Hydrated Dolomitic Lime; Calcium Magnesium Hydroxide; Double Hydrated Dolomitic Lime

Chemical Identity CAS # Concentration, % Wt. Calcium Hydroxide 1305-62-0 > 50 Magnesium Hydroxide 1309-42-8 > 35 Crystalline Silica 14808-60-7 < 1

Type S Hydrated Lime – May 1, 2015

SECTION 4 FIRST AID MEASURES Eye Contact: Contact can cause severe irritation or burning of eyes, including permanent

damage. Immediately flush eyes with generous amounts of water for several minutes. Pull back the eyelid to ensure that all lime dust has been washed out. Seek medical attention immediately. Do not rub eyes.

Inhalation: This product can cause severe irritation of the respiratory system. Move victim to

fresh air. Seek medical attention if necessary. If breathing has stopped, give artificial respiration.

Skin Contact: Contact can cause severe irritation or burning of skin, especially in the presence of moisture. Wash exposed area with large amounts of water. Seek medical attention immediately.

Ingestion: This product can cause severe irritation or burning of gastrointestinal tract if swallowed. Do not induce vomiting. Seek medical attention immediately. Never give anything by mouth unless instructed to do so by medical personnel.

Most important symptoms and effects, both acute and delayed: Irritation of skin, eyes, gastrointestinal tract or respiratory tract. Long-term exposure by inhalation may cause permanent damage. This product contains crystalline silica, which has been classified by IARC as (Group I) carcinogenic to humans when inhaled. Inhalation of silica can also cause a chronic lung disorder, silicosis.

Note to Physician: Provide general supportive measures and treat symptomatically.

SECTION 5 FIREFIGHTING MEASURES Extinguishing Media

Appropriate Extinguishing Media: Use dry chemical fire extinguisher

Inappropriate Extinguishing Media: Do not use halogenated compounds.

Firefighting

Fire Hazards: Type S Hydrated Lime is not combustible or flammable. Type S Hydrated Lime is not considered to be an explosive hazard, although reaction with incompatible materials may rupture containers.

Hazardous Combustion Products: None

Special Protective Equipment and Fire Fighting Instructions: Keep personnel away from and upwind of fire. Wear full fire-fighting turn-out gear (full Bunker gear), and respiratory protection (SCBA).

Type S Hydrated Lime – May 1, 2015

SECTION 6 ACCIDENTAL RELEASE MEASURES Personal Precautions: Use proper protective equipment. Environmental Precautions: For large spills, as much as possible, avoid the generation of dusts. Prevent release to sewers or waterways.

Methods and Materials for Containment and Cleaning Up:

Small Spills: Use dry methods to collect spilled materials. Avoid generating dust. Do not clean up with compressed air. Store collected materials in dry, sealed plastic or metal containers. Residue on surfaces may be washed with water or dilute vinegar.

Large Spills: Use dry methods to collect spilled materials. Evacuate area downwind of clean-up operations to minimize dust exposure. Store spilled materials in dry, sealed plastic or metal containers.

SECTION 7 HANDLING AND STORAGE Precautions for Safe Handling: Keep in tightly closed containers. Protect containers from physical damage. Avoid direct skin contact with the material. Conditions for Safe Storage, Including any Incompatibilities: Store in a cool, dry, and well-ventilated location. Do not store near incompatible materials (see Section 10 below). Keep away from moisture. Do not store or ship in aluminum containers.

SECTION 8 EXPOSURE CONTROLS/ PERSONAL PROTECTION

Control Parameters:

Component CAS # Exposure Limits Calcium Hydroxide

1305-62-0 OSHA PEL: 15 mg/m3 (total) 5 mg/m3 (respirable) ACGIH TLV: 5 mg/m3

Magnesium Hydroxide

1309-42-8 OSHA PEL: 15 mg/m3 ACGIH TLV: 5 mg/m3

Crystalline Silica 14808-60-7 OSHA PEL: 10 mg/m3 divided by (the percentage of silica in the dust plus 2) (respirable) ACGIH TLV: 0.025 mg/m3 (respirable)

Appropriate Engineering Controls: Provide ventilation adequate to maintain PELs. Personal Protection

Respiratory Protection: Use NIOSH approved respirators if airborne concentration exceeds PEL.

Type S Hydrated Lime – May 1, 2015

Eye Protection: Use safety glasses with side shields or safety goggles. Contact lenses should not be worn when working with lime products.

Skin Protection: Use appropriate gloves to prevent skin contact. Clothing should fully cover arms and legs.

Other: Eye wash fountain and emergency showers are recommended.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance

Physical State: Solid

Color: White

Odor: Odorless

Odor Threshold: N/ A

pH: 12.44 @ 25o C

Melting Point: N/ A

Initial Boiling Point: N/ A

Freezing Point: N/ A

Flash Point: N/ A

Evaporation Rate: N/ A

Flammability (solid, gas): Non-flammable

Explosion Limits: N/ A

Vapor Pressure: N/ A

Vapor Density: N/ A

Relative Density: 0.4 – 0.7 g/ cm3 (apparent)

Solubility(ies): Solubility is 1.6 g/L at 25o C

Partition coefficient: Relatively insoluble

Auto-ignition Temperature: N/ A

Decomposition Temperature: 580o C / 1076o F

Viscosity: N/A

Type S Hydrated Lime – May 1, 2015

SECTION 10 STABILITY AND REACTIVITY Reactivity:

Chemical Stability: Type S Hydrated Lime is chemically stable.

Possibility of Hazardous Reactions: See reactivity above

Conditions to Avoid: Do not allow Type S Hydrated Lime to come into contact with incompatible materials.

Incompatible Materials: Type S Hydrated Lime should not be mixed or stored with the following materials, due to the potential for violent reaction and release of heat:

Acids (unless in a controlled process) Reactive Fluoridated Compounds Reactive Brominated Compounds Reactive Powdered Metals Organic Acid Anhydrides Nitro-Organic Compounds Reactive Phosphorous Compounds Interhalogenated Compounds

Hazardous Decomposition Products: None

SECTION 11 TOXICOLOGICAL INFORMATION Health Effects: see First Aid discussion in Section 4

Routes of Exposure: see First Aid discussion in Section 4

Symptoms Related to Exposure: see First Aid discussion in Section 4

Carcinogen Listing: Type S Hydrated Lime is not listed by MSHA, OSHA, or IARC as a carcinogen, but this product contains crystalline silica, which has been classified by IARC as (Group I) carcinogenic to humans when inhaled.

SECTION 12 ECOLOGICAL INFORMATION Ecotoxicity: Because of the high pH of this product, it would be expected to produce

significant ecotoxicity upon exposure to aquatic organisms and aquatic systems in high concentrations.

Persistence and Degradability: Reacts with atmospheric CO2 over time to form calcium

carbonate

Bioaccumulation Potential: This material shows no bioaccumulation effect or food chain concentration toxicity.

Type S Hydrated Lime – May 1, 2015

Mobility in Soil: Minimal mobility in soil. Reacts with clay portion of soil to form calcium silicates and calcium aluminates

Other Adverse Effects: This material is alkaline and if released into water or moist soil will cause an increase in pH

SECTION 13 DISPOSAL CONSIDERATIONS Disposal Recommendations: Dispose of in accordance with all applicable federal, state, and

local environmental regulations.

Regulatory Disposal Information: If this product as supplied, and unmixed, becomes a waste, it will not meet the criteria of a hazardous waste as defined under the Resource Conservation and Recovery Act.

SECTION 14 TRANSPORT INFORMATION UN Number: Not Regulated

UN Proper Shipping Name: Not Regulated

Transport Hazard Class(es): Not Regulated

Packing Group: Not Regulated

Marine Pollutant (y/n): This material is alkaline and if released into water or moist soil will cause an increase in pH.

Special Precautions: None

SECTION 15 REGULATORY INFORMATION National Chemical Inventory Listings:

All chemical ingredients are listed on the USEPA TSCA Inventory List.

US Regulations: RCRA Hazardous Waste Number: not listed (40 CFR 261.33) RCRA Hazardous Waste Classification (40 CFR 261): not classified CERCLA Hazardous Substance (40 CFR 302.4) unlisted specific per RCRA, Sec. 3001; CWA, Sec. 311 (b) (4); CWA, Sec. 307(a), CAA, Sec. 112 CERCLA Reportable Quantity (RQ) not listed. SARA 311/312 Codes: not listed. SARA Toxic Chemical (40 CFR 372.65): not listed. SARA EHS (Extremely Hazardous Substance) (40 CFR 355): Not listed, Threshold Planning Quantity (TPQ): not listed

Specific State Regulations: Consult State and Local authorities for guidance. Components found in this product may contain trace amounts of inherent naturally occurring elements (such as, but not limited to arsenic and cadmium) that may be regulated under California Proposition 65 and other States regulations.

Type S Hydrated Lime – May 1, 2015

Canada DSL: Listed

Canadian WHMIS Listing:

“E” Corrosive Materials [listed due to corrosive effect on aluminum]

“D2A” Materials causing other toxic effects SECTION 16 OTHER INFORMATION Prepared By: Lhoist North America Technical Services

Date Prepared: May 1, 2015

Revision: 2015-1

Abbreviations:

N/A Not Available or Not Applicable IARC International Agency for Research on Cancer IATA International Air Transport Association

ACGIH ACGIH American Conference of Governmental Industrial Hygienists

TWA Time Weighted Average PEL Permissible Exposure Limit TLV Threshold Limit Value REL Recommended Exposure Limit Lhoist North America provides the information contained herein in good faith but makes no representation as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person. Individuals receiving this information must consult their own technical and legal advisors and/ or exercise their own judgment in determining its appropriateness for a particular purpose. Lhoist North America makes no representations or warranties, either express or implied, including without limitation and warranties of merchantability or fitness for a particular purpose with respect to the Information set forth herein or the product(s) to which the information refers. Accordingly, Lhoist North America will not be responsible or liable for any claims, losses or damages resulting from the use of or reliance upon or failure to use this information.

TILING 09 30 00 Setting / TDS-119

1 Product Name

VersaBond® Fortified Thin­Set Mortar

2 Manufacturer

Custom® Building Products

3 Product Description

A professional formula, all-purpose mortar, polymer-modified toprovide good bond strength for floor and tile projects. VersaBond®cures quickly even in cold climates and adheres to most surfaces,exceeding ANSI A118.4 and A118.11 without the need for additives.

Suitable Tile Types

Vitreous, semi-vitreous or non-vitreous tile: ceramic, mosaic, quarry,cement body tile

Impervious porcelain and glass tileBrick and thin brickCement-based precast terrazzoNatural stone tile

Suitable Substrates

Concrete, mortar beds, masonry, Portland cement plasterWonderBoard® cement backerboardsLiquid applied waterproofing membranes such asRedGard®andCustom® 9240Crack prevention sheet membranes such asCrack Buster® ProExterior Grade Plywood (interior residential and light commercial dryareas)Gypsum wallboard (interior dry areas)Existing ceramic tile (scarified)Fully-bonded sheet vinyl flooring (scarified)Plastic laminates (scarified)Cutback adhesive (see preparation instructions)

Composition of Product

VersaBond® Fortified Thin­Set Mortar is a dry, proprietary blend ofPortland cement, copolymers, inorganic aggregates and chemicals

Benefits of Product in the Installation

Cost-efficient, all-purpose mortarGood bond strengthCures quickly even in cold climatesExceeds ANSI A118.4 and A118.11 standards without the need foradditives

Limitations to the Product

Do not bond directly to hardwood, Luan plywood, particle board,parquet, cushion or sponge-back vinyl flooring, metal, fiberglass,plastic or OSB panels.When setting moisture sensitive natural stone, cement or agglomeratetile use EBM­Lite™ Epoxy Bonding Mortar 100% Solids or CEG­Lite™

100% Solids Commercial Epoxy Grout.Do not use to install resin­backed stone use EBM­Lite™ Epoxy Bonding

Mortar 100% Solids, CEG­Lite™ 100% Solids Commercial Epoxy Grout

or contact Custom's® Technical Services for recommendations.

When setting glass tile larger than 6" x 6" (15 x 15 cm), contactCustom's® Technical Services for recommendations.

When setting dimensional stone larger than 12" x 12" (30 x 30 cm),contact Custom's® Technical Services for recommendations regarding

subfloor deflection requirements.

Packaging

50 lb (22.68 kg) and 25 lb (11.34 kg) bagsGray or white

4 Technical Data

Applicable Standards

American National Standards Institute (ANSI) — ANSI A108.5, A137.2,A118.4 and A118.11 of the American National Standards for theInstallation of Ceramic Tile ASTM International (ASTM)

ASTM C109 Standard Test Method for Compressive Strength ofHydraulic Cement Mortars (Using 2-in or [50-mm] Cube Specimens)ASTM C627 Standard Test Method for Evaluating Ceramic Floor TileInstallation Systems Using the Robinson-Type Floor Tester ResilientFloor Covering Institute — (RFCI) Recommended Work Practices for

Removal of Resilient Floor Coverings Tile Council of North America(TCNA) — TCNA Handbook for Ceramic Tile Installation, TCNA Method

EJ171ISO 13007-2

VersaBond® Fortified Thin­Set Mortar

Published Date: April 09 2013

TILING 09 30 00 Setting / TDS-119

Technical Chart

Property Test Method Requirement Typical ResultsPot Life 4 HoursOpen Time A118.4

Section 4.4> 50Minutes

50 - 55 Minutes

Adjustment Time A118.4Section 4.5

> 30Minutes

30 - 35 Minutes

4 Week ShearBond Strength

Glazed Wall Tile A118.4Section 5.1.5

> 300 psi 450 - 550 psi(31.6 - 38.7kg/cm²)

Porcelain Tile A118.4Section 5.2.4

> 200 psi 300 - 400 psi(21.1 - 28.1kg/cm²)

Quarry Tile toPlywood

A118.11Section 4.1.2

> 150 psi 150 - 250 psi(10.5 - 17.6kg/cm²)

Sag on Walls A118.4Section 4.6

< 1/16"

Environmental Consideration

Custom® Building Products is committed to environmentalresponsibility in both products produced and in manufacturingpractices. Use of this product can contribute to LEED® certification.

5 Instructions

General Surface Prep

Surfaces must be structurally sound. Remove all grease, oil, dirt,curing compounds, sealers, adhesives or any other contaminant thatwould prevent a good bond. Glossy or painted surfaces must besanded, or abraded, and stripped of all contaminants. Concrete mustbe cured 28 days and accept water penetration. Concrete must be freeof efflorescence and not subject to hydrostatic pressure. Concreteslabs should have a course finish to enhance the bond. Plywoodflooring including those under resilient flooring must be structurallysound and meet all ANSI and deflection requirements. For questionsabout proper subfloor installation, call Technical Services. Smoothconcrete surfaces, existing glazed tile, terrazzo, or polished stoneshould be scarified. Sheet vinyl must be well bonded and stripped ofold finish. Roughen the surface by sanding or abrading, then rinse andallow to dry. Expansion joints should never be bridged with settingmaterial. Do not sand flooring materials containing asbestos. Ambienttemperature should be maintained above 50° F (10° C) or below 100°F (38° C) for 72 hours to achieve proper bond.

Bonding to Cement Surfaces

Concrete or plaster must be fully cured and must accept waterpenetration. Test by sprinkling water on various areas of the substrate.If water penetrates, then a good bond can be achieved; if waterbeads, surface contaminants are present, and loss of adhesion mayoccur. Contaminants should be mechanically removed beforeinstallation. Concrete must be free of efflorescence and not subject tohydrostatic pressure. Concrete slabs should have a course finish toenhance the bond. Smooth concrete slabs must be mechanicallyabraded to achieve proper bond.

Bonding to Lightweight Cement and Gypsum Surfaces

Lightweight or gypsum based underlayments must obtain a minimum2000 psi (13.8 MP) compressive strength. The underlayment must besufficiently dry and properly cured to the manufacturer’s specificationsfor permanent, non-moisture permeable coverings. Surfaces to betiled must be structurally sound and subject to deflection not to exceedthe current ANSI Standards. Surfaces shall be free of all grease, oil,dirt, dust, curing compounds, waxes, sealers, efflorescence, or anyother foreign matter. All Lightweight cement or Gypsum surfacesshould be primed with a properly applied sealer or a primer coat ofRedGard, consisting of 1 part RedGard diluted with 4 parts clean, coolwater. Mix in a clean bucket at low speed to obtain a lump freesolution. The primer can be brushed, rolled or sprayed to achieve aneven coat. Apply the primer coat to the floor at a rate of 300 sq. ft.l(7.5 sq. m/L). Drying time depends on site conditions, but is normallyless than 1 hour. Extremely porous surfaces may require 2 coats. Atthis point, RedGard can be applied to the primed lightweight or gypsumbased surface. Refer to the individual product data sheet or packagingdirections for application instructions. Expansion joints must beinstalled in accordance with local building codes and ANSI/TCNAguidelines. Refer to TCNA EJ171.

Bonding to Plywood Surfaces

Plywood floors, including those under resilient flooring, must bestructurally sound and must meet all ANSI A108.01 Part 3.4requirements. Maximum allowable deflection: L/360 tile L/720 stone.See TCNA F150. For questions about proper subfloor installation, callCustom Building Products.

Bonding to Wonderboard Backerboards

As an alternative to an additional layer of plywood, WonderBoardbackerboard may be installed over plywood subfloors for ceramic tileinstallations. Refer to TCNA F144. Call tech support when installingnatural stone over plywood subfloor (TCNA F-141-11 & F-250-11).Only appoved installation methods for stone.

Bonding to Existing Surfacing Material

Existing Ceramic Tile, Resilient Flooring or Plastic Laminates: Resilientflooring or plastic laminates must be well bonded, as well as clean andfree of all contaminates. Roughen the surface by sanding or scarifying;rinse and allow to dry. Do not sand flooring that contains asbestos. Forexisting well bonded ceramic tile, mechanically abrade the surface.Rinse and allow to dry. When sanding, an approved respirator shouldbe used.

Bonding to Cutback Adhesive

Adhesive layers must be removed, as they reduce mortar bondstrength to cement surfaces. Use extreme caution; adhesives maycontain asbestos fibers. Do not sand or grind adhesive residue, asharmful dust may result. Never use adhesive removers or solvents, asthey soften the adhesive and may cause it to penetrate into theconcrete. Adhesive residue must be wet scraped to the finishedsurface of the concrete, leaving only the transparent staining from theglue. To determine desirable results, do a test bond area beforestarting. Refer to the RFCI Pamphlet, “Recommended Work Practicesfor Removal of Resilient Floor Coverings” for further information.

VersaBond® Fortified Thin­Set Mortar

Published Date: April 09 2013

TILING 09 30 00 Setting / TDS-119

Expansion Joint placement

Expansion joints and cold joints, as described in ANSI A108.01, shouldnever be bridged with setting material. They must be brought throughthe tile work and filled with an appropriate elastomeric sealant, suchas Custom's 100% Silicone. Contact Custom's Technical Services forthe proper treatment of control or saw cut joints. Refer to TCNAEJ171, F125 & F125A.

Mixing Ratios - powder to water

Mix 6 qts (5.68 L) clean water per 50 lb (22.68 kg) bag of mortar.

Mixing Procedures

Mix by hand or use a low 150 – 200 rpm speed 1/2" (13 mm) drill toachieve a smooth, paste-like consistency. Let the mixture slake orstand 5 – 10 minutes; stir again and use. Stir occasionally, but do notadd more water. When properly mixed, troweled ridges will standwithout slump.

Application of Product

Installation must conform to ANSI A108.5. Use a properly-sized notchtrowel to ensure proper coverage under tiles. Using the flat side of thetrowel, apply a skim coat of mortar to the surface. With the notch sideof the trowel held at a 45© angle, apply additional mortar to thesurface, combing in one direction. Press the tile firmly into place in aperpendicular motion across ridges, moving back and forth. Theperpendicular motion flattens ridges and closes valleys, allowingmaximum coverage. With some tile, back-buttering is advisable. Adjustthe tile promptly and beat it in with a beating block and rubber mallet.Periodically pull up a tile and check the back to ensure proper adhesivecoverage. If the material has skinned over (not sticky to the touch),recomb with the notch trowel; if too dry, remove and replace the drymaterial with fresh material. Material in the bucket will remainworkable for approximately 4 hours.

Curing of Product

Curing time is affected by ambient and surface temperatures andhumidity. Use the following as a guideline. Allow 24 hours beforegrouting or light traffic.

Cleaning of equipment

Clean with water before the material dries.

Storage

Store in a cool dry area.

Health Precautions

This product contains Portland cement and free silica. Avoid eyecontact or prolonged contact with skin. Wash thoroughly afterhandling. If eye contact occurs, flush with water for 15 minutes andconsult a physician. Do not breathe dust; wear a NIOSH approvedrespirator

Conformance to Building Codes

Installation must comply with the requirements of all applicable local,state and federal code jurisdictions.

6 Availability & Cost

VersaBond Flex®Fortified Thin-SetMortar

Product Name Location ItemCode

Size Color Package

USA MTSG25 25 lb(11.34kg)

Gray Bag

USA MTSG50 50 lb(22.68kg)

Gray Bag

USA MTSW50 50 lb(22.68kg)

White Bag

Canada CVBG50 50 lb(22.68kg)

Gray Bag

Canada CVBW50 50 lb(22.68kg)

White Bag

7 Product Warranty

Custom Building Products warrants to the original consumer purchaserthat its product shall be free from defects in material and workmanshipunder normal and proper usage for a period of one year following thedate of original purchase. Custom’s sole liability under this warrantyshall be limited to the replacement of the product. Some states,countries or territories do not allow the exclusion or limitation ofincidental or consequential damages, so the above limitation orexclusion may not apply to you. This warranty will not extend to anyproduct which has been modified in any way or which has not beenused in accordance with Custom’s printed instructions. Custom makesno other warranties either expressed or implied. This warranty givesyou specific legal rights, and you may have other rights that vary fromstate to state or from one country/territory to another. Click for detailsand complete warranty information.

8 Product Maintenance

Properly installed product requires no special maintenance.

9 Technical Services Information

For technical assistance, contact Custom® Building Products.

10 Filing System

Additional product information is available from the manufacturer uponrequest.

Expected Wear

Properly installed tile will last for more than 60 years.

Related Products

Polyblend® Sanded Grout

VersaBond® Fortified Thin­Set Mortar

Published Date: April 09 2013

TILING 09 30 00 Setting / TDS-119

Coverage

SQUARE FOOT COVERAGE PER 50 LB BAG (SQUARE METER PER 22.68 KG)

Trowel Size Min Coverage Max Coverage1/4" x 1/4" x 1/4" (6 x 6 x 6 mm) Square-Notch 85 sq. ft. (8.8 M²) 95 sq. ft. (8.8 M²)

1/4" x 3/8" x 1/4" (6 x 9.5 x 6 mm) Square-Notch 60 sq. ft. (5.6 M²) 67 sq. ft. (6.2 M²)

1/2" x 1/2" x 1/2" (13 x 13 x 13 mm) Square-Notch 42 sq. ft. (3.9 M²) 47 sq. ft. (4.4 M²)

3/4" × 9/16" × 3/8" (19 × 14 × 9.5 mm) U­Notch 34 sq. ft. (3.2 M²) 38 sq. ft. (3.5 M²)

VersaBond® Fortified Thin­Set Mortar

Published Date: April 09 2013

Surface Prep / TDS-104

1 Product Name

RedGard® Crack Prevention and Waterproofing Membrane

2 Manufacturer

Custom Building ProductsTechnical Services10400 Pioneer Boulevard, Unit 2Santa Fe Springs, CA 90670Customer Support: 800-272-8786Technical Services: 800-282-8786Fax: 800- 200-7765Email: contactus@cbpmail.netcustombuildingproducts.com

3 Product Description

A ready-to-use elastomeric waterproofing membrane for bothcommercial and residential tile and stone application. Suited forinterior and exterior substrates, RedGard® creates a continuouswaterproofing barrier with outstanding adhesion and reduces cracktransmission in tile and stone floors. It bonds directly to clean metaldrains, PVC, stainless steel and ABS drain assemblies and can be usedas a slab-on-grade moisture vapor barrier under all types of floorcoverings.

Key Features

Ready to use - Roll it onQuick dry formula - 30% faster dryingListed with IAPMO for use as a shower pan liner

Suitable Substrates

Concrete, cement mortar, masonryCement BackerboardExterior Plywood and OSB (interior, dry areas only)Exterior Decks - Contact Technical ServicesPost-Tension Concrete - Contact Technical ServicesLightweight Concrete (min. 2000 psi compressive strength)Gypsum-Based cement topping (min. 2000 psi compressive strength)Existing ceramic tile and resilient flooring

Composition of Product

RedGard® is a liquid-applied elastomeric waterproofing material thatcures to form a monolithic membrane.

Benefits of Product in the Installation

Easy to use and can be applied by roller, trowel or airless sprayerRated for extra heavy duty serviceReduces curing time with quick-dry formulaIsolates cracks to 1/8" (3 mm)Suitable for waterproofing pools, spas and water featuresMeets Uniform Plumbing Code specifications for use as a shower panlinerObtained the Notice of Acceptance (NOA) for Miami-Dade County

Limitations to the Product

Do not apply to surfaces that may drop below 40°F (4°C) within 72

hours of application.Do not apply over wet surfaces or surfaces subject to hydrostaticpressure.Do not use to bridge or cover over existing expansion, control,construction, cold or saw cut joints; use Crack Buster® Pro Membrane

for control, cold or saw cut joints.Do not use as an adhesive.Do not use as a wear surface; the membrane must be covered withtile or other permanent flooring.Do not use solvents in conjunction with the membrane

Packaging

1 gallon (3.78 L) pail3.5 gallon (13.2 L) pail

4 Technical Data

Applicable Standards

American National Standards Institute (ANSI) ANSI A108.01, A108.17,A108.13, A118.10 and A118.12 American National Standards for theInstallation of Ceramic Tile ASTM International (ASTM)

ASTM C627 Standard Test Method for Evaluating Ceramic Floor TileInstallation Systems Using the Robinson-Type Floor TesterASTM D638 Standard Test Method for Tensile Properties of Plastics

Tile Council of North America (TCNA) TCNA Handbook for Ceramic TileInstallation, TCNA Method EJ171, F125 & F125A

RedGard® Crack Prevention and Waterproofing Membrane

Published Date: 1/8/2015

Surface Prep / TDS-104

Approvals

RedGard® has tested and complies with Uniform Plumbing Code andInternational Plumbing Code standards for use as a shower pan linerper IAPMO Research and Testing, Inc., File No. 4244. RedGard® hastested and complies with International Building Code (IBC),International Residential Code (IRC) and International Plumbing Code(IPC) standards for water resistance per ICC Evaluation Service, ESR-413. RedGard® complies with the Product Control Division of theMiami Dade County Building Code Compliance Office for waterproofingstandards and has earned a Notice of Acceptance (NOA), File No. 07-1010.16. RedGard® conforms to “safing material” requirementsestablished by the Wisconsin Administrative Code, Chapter Comm84.30-6f.

Technical Chart

Property Test Method Requirement Typical Results

FungusResistance

A118.10Section 4.1

No Growth Pass

Seam Strength A118.10Section 4.2

> 8 lbs/"width

16 lbs/2" (7.3kg/5 cm) width

BreakingStrength

A118.10Section 4.3

> 170 psi 484 psi (34kg/cm²)

DimensionalStability

A118.10Section 4.4

+/- 0.7% 0.05%

Waterproofness A118.10Section 4.5

No WaterPenetration

Pass

Steam ShowerRequirement

ASTM E-96Method E

< 0.5 perms 0.35 perms

Shear Bond Strength to Cement MortarFour Week ShearStrength

A118.10Section 5.5

> 50 psi 267 psi (18.8kg/cm²)

Shear StrengthAfterWater Immersion

A118.10Section 5.4

> 50 psi 89 psi (6.3 kg/cm²)

System Crack ResistanceStandardPerformance

A118.12Section 5.4

> 1/16" and <1/8"

Pass

HighPerformance

A118.12Section 5.4

> 1/8" Pass

Point Load A118.12Section 5.2

> 1000 lbs > 1000 psi

Robinson Test A118.12Section 5.3

As Specified 14 Cycles; ExtraHeavy

Environmental Consideration

Custom® Building Products is committed to environmentalresponsibility in both products produced and in manufacturingpractices. Use of this product may contribute to LEED® certification.

5 Instructions

General Surface Prep

USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when

handling product.

Exterior and wet areas must have proper sloping to drains. All surfacesmust be structurally sound, clean, dry and free from contaminants thatwould prevent a good bond. Newly prepared concrete must betroweled smooth and textured to a fine broom finish and cured for 28days. Existing surfaces must be scarified and leveled, and all defectsmust be repaired. Cracks exceeding 1/8" (3 mm) should be treated inaccordance with TCNA F125 or TCNA F125A.

Bonding to Lightweight Cement and Gypsum Surfaces

Lightweight or gypsum-based materials must obtain a minimum of2000 psi (13.8 MPa) compressive strength at the recommended curetime. The underlayment must be sufficiently dry and properly cured tothe manufacturer's specifications for permanent, non-moisturepermeable coverings. Surfaces to be covered must be clean,structurally sound and subject to deflection not to exceed the currentANSI standards. Expansion joints must be installed in accordance withlocal building codes and ANSI/TCNA guidelines. Prime all surfaces toreceive RedGard® with properly applied manufacturer's sealer or witha primer coat of RedGard®, consisting of 1 part RedGard®, dilutedwith 4 parts clean, cool water. In a clean pail, mix at low speed toobtain a lump-free solution. The primer can be brushed, rolled orsprayed to achieve an even coat. Apply the primer coat to the floor ata rate of 300 ft/gallon (7.5 M/L) of reduced material. When dry, applyat least one full coat of RedGard® to the primed area.

Vapor Barrier

When used as a vapor barrier, apply one full coat (20 to 25 mils wet)where vapor transmission is up to 8 lbs per 1000 sq. ft per day andtwo full coats (20 to 25 mils wet each coat) where vapor transmissionis up to 12 lbs per 1000 sq. ft per day. Refer to ASTM F1869 for moreinformation on Vapor Transmission Testing.

Movement Joint Placement

Do not bridge joints designed to experience movement. Carry thesetypes of joints through the tile work. Clean the joint and install an openor closed cell-backer rod to the proper depth, as outlined in the TileCouncil Handbook, EJ171. Next compress sealant into the joint, coatingthe sides and leaving the sealant flush with the surface. When thesealant is dry, place bond-breaker tape over the joint. Apply aminimum 3/64" (1.2 mm) of RedGard® over the joint and thesubstrate, following the instructions provided previously. Install the tilework onto the membrane, but do not bridge the joint. After the tilework is properly set, follow the architect's and manufacturer'sinstructions to fill the joint with a specified color sealant.

Application of Product

RedGard® Crack Prevention and Waterproofing Membrane

Published Date: 1/8/2015

Surface Prep / TDS-104

RedGard at Drains

Drains should have a clamping ring with open weep holes for thin-setapplication. Apply the membrane to the bottom of the flange. Thedrain should be fully supported, without movement, and should beeven with the plane of the substrate. Apply the RedGard membranearound drain. Embed a 12" x 12" (30 x 30 cm) fiberglass mesh into themembrane, making sure it does not obstruct the drainage weep holes.Then apply an additional coat of the membrane and smooth. Aftercuring, clamp the upper flange onto the membrane and tighten. Use asilicone caulk around the flange where the membrane and the upperflange make contact. A toilet flange can be handled in much the samemanner.

RedGard® as Crack Prevention Membrane

Force RedGard® into cracks with the flat side of the trowel, roller orbrush. Using a 3/16"-1/4" (5-6 mm) V-notch trowel or 3/8" (9.5 mm)rough textured roller. Use the flat side of the trowel and flatten theridges to form a continuous, even coat of material. The membraneshould extend a minimum of the diagonal measurement of the tilebeyond both sides of the crack. Gaps between plywood sheets andwhere floors meet walls must also be prefilled. For continuous crackisolation, cover the entire substrate with RedGard® applied to aminimum 30 mils wet-film thickness.

RedGard® as General Waterproof Membrane (ANSI 118.10)

Cracks to 1/8" (3 mm) should be prefilled before beginning thewaterproofing application. Lightly dampen all porous surfaces. Use a3/4" (19 mm) rough-textured synthetic roller or a 3/16"-1/4" (5-6 mm)V-notch trowel and heavily pre-coat the corners and the intersectionswhere the floors and walls meet, extending 6" (15 cm) on either side.

RedGard® applied in the above manner meets requirements of ANSIA118.10 without fabric reinforcement. For extra protection, embed a6" (15 cm) wide fiberglass mesh into the membrane for changes ofplane and for gaps 1/8" (3 mm) or greater. If using a trowel, spreadthe material with the trowel held at a 45° angle, and then flattens theridges. If using a roller, apply a continuous, even film with overlappingstrokes. An airless sprayer may be used for the waterproofingapplication. The sprayer must produce between 1900-2300 psi, with aflow rate of 1.0-1.5 GPM and must have a tip orifice size of 0.025-0.029. Apply a continuous film with overlapping spray. The membraneappearance is pink when wet and dries to a dark red color. It typicallytakes 1-1.5 hours to turn completely red. After the first coat turns red,inspect the film for integrity and fill any voids or pinholes withadditional material. Apply a second coat at right angles to the firstcoat. Periodically check the film thickness with a wet-film gauge.Combined dried coatings must be at least 30-35 mils thick. When wet,the combined coatings must be at least 60-70 mils and must notexceed 125 mils wet-film thickness.

Curing of Product

RedGard® is dry when it turns solid red, with no visible pink color.Typically, drying time is 1-1.5 hours; depending on ambient conditions,drying time can be as much as 12 hours. After the second coat isapplied and both coats are fully cured, the application area can beflood tested.

Protection

If tile or stone will not be set immediately after curing, protect theapplication from heavy traffic damage. Protect from rain and inclementweather for 72 hours after application. If delays longer than 72 hoursare expected, cover the area with felt paper. Care should be taken toprevent the application from becoming soiled or punctured during andafter application.

Tile and Stone Installation

Install tile or stone with a Custom® Building Products polymer­modified mortar that meets ANSI A118.4 or A118.15 standards.

Cleaning of equipment

Clean tools and hands with water before the material dries. Clean allspray equipment immediately after use.

Health Precautions

Wear rubber gloves and eye protection while using this product. Avoideye contact or prolonged contact with skin and wash thoroughly afterhandling. If eye contact occurs, flush with water for 15 minutes andconsult a physician. Wash thoroughly after handling. Do not takeinternally. Keep out of the reach of children.

Conformance to Building Codes

Installation must comply with the requirements of all applicable local,state and federal code jurisdictions.

6 Availability & Cost

ColorLocation Item Code Size Package

USA LQWAF1 1 gallon (3.78 L) Pink PailUSA LQWAF3 3.5 gallon (13.2 L) Pink PailCanada CLLQWAF1 1 gallon (3.78 L) Pink PailCanada CLLQWAF3 3.5 gallon (13.2 L) Pink Pail

RedGard® Crack Prevention and Waterproofing Membrane

Published Date: 1/8/2015

Surface Prep / TDS-104

7 Product Warranty

Custom® Building Products warrants to the original consumerpurchaser that its product shall be free from defects in material andworkmanship under normal and proper usage for a period of one yearfollowing the date of original purchase. CUSTOM's sole liability underthis warranty shall be limited to the replacement of the product. Somestates, countries or territories do not allow the exclusion or limitationof incidental or consequential damages, so the above limitation orexclusion may not apply to you. This warranty will not extend to anyproduct which has been modified in any way or which has not beenused in accordance with CUSTOM's printed instructions. CUSTOMmakes no other warranties either expressed or implied. This warrantygives you specific legal rights, and you may have other rights that varyfrom state to state or from one country/territory to another. Thiswarranty is not transferrable.

When RedGard® Waterproofing and Crack Prevention Membrane isused as a part of a qualifying full installation system of CUSTOMproducts, the installation can qualify for up to a lifetime systemwarranty. CUSTOM will repair and/or replace, at its discretion, theaffected area of the system. For more information, find details andlimitations to this warranty at custombuildingproducts.com.

8 Product Maintenance

Properly installed product requires no special maintenance. Do not useas a wear surface.

9 Technical Services Information

For technical assistance, contact Custom technical services at 800-272-8786 or visit custombuildingproducts.com.

10 Filing System

Additional product information is available from the manufacturer uponrequest.

Related Products

RedGard® Fabric Membrane

RedGard® Crack Prevention and Waterproofing Membrane

Published Date: 1/8/2015

Surface Prep / TDS-104

Coverage

Size Thickness Min Coverage Max Coverage

RedGard as Crack Prevention Membrane:1 Gallon (3.78 L) 30 mil thickness when wet 110 sq. ft. (10.2 M²) 3.5 Gallon (13.2 L) 30 mil thickness when wet 385 sq. ft. (35.8 M²) RedGard as Waterproof Membrane (ANSI A118.10):1 Gallon (3.78 L) 60 mil thickness when wet; 30 mil thickness when dry 35 sq. ft. (3.3 M² ) 40 sq. ft. (3.7 M²)

3.5 Gallon (13.2 L) 60 mil thickness when wet; 30 mil thickness when dry 123 sq. ft. (11.4 M²) 140 sq. ft. (13 M²)

RedGard as IAPMO Pan Liner:1 Gallon (3.78 L) 60 mils when wet; 30 mils when dry 35 sq. ft. (3.3 M²) 40 sq. ft. (3.7 M²)

3.5 Gallon (13.2 L) 60 mils when wet; 30 mils when dry 123 sq. ft. (11.4 M²) 140 sq. ft. (13 M²)

RedGard® Crack Prevention and Waterproofing Membrane

Published Date: 1/8/2015

Grout / TDS-129

1 Product Name

Polyblend® Sanded Grout

2 Manufacturer

Custom Building Products13001 Seal Beach Blvd.Seal Beach, CA 90740-2757Customer Support: 800-272-8786Technical Services: 800-282-8786Fax: 800- 200-7765Email: contactus@cbpmail.netcustombuildingproducts.com

3 Product Description

A polymer-modified, cement based sanded grout that produces hard,dense joints that resist shrinking, cracking and wear. Formulated fordurability, Polyblend® Sanded Grout accommodates 1/8"­1/2" (3­13mm) joints for interior or exterior installations, including floors,countertops, walls, ceilings, showers, fountains and pools.

Key Features

Easy to use - Just mix with waterPolymer fortified for hard, durable, professional results

Uses

Use to fill joint widths 1/8" to 1/2" (3.2 to 13 mm)May be used for both floor and wall installationsInterior and exterior applicationsResidential and commercial applicationsCountertops, tub surrounds, showers and high traffic areasSubmerged conditions (swimming pools, spas, water features andfountains)

Suitable Tile Types

Vitreous, semi-vitreous or non-vitreous tile: ceramic, mosaic, quarry,cement body tilesImpervious porcelain and glass tileBrick and stone veneerCement-based precast terrazzoNatural stone tile

Composition of Product

Polyblend® Sanded Grout is a dry, Portland cement based grout withsilica sand, inorganic aggregates and chemicals.

Benefits of Product in the Installation

Hard, durable grout jointsResists shrinking, cracking, powdering and wear

Limitations to the Product

Should not be installed when ambient or surface temperature is lowerthan 50°F (10°C) or higher than 100°F (38°C).

Some ceramic, glass, marble or stone tiles can be scratched ordamaged by the silica aggregate filler. Perform a test on a small areaprior to use. Polyblend® Non­Sanded Grout may be appropriate forjoints up to 1/8" or for tile not suited for sanded grout.Tile or stone with high absorption, surfaces that are porous or rough,textured surfaces and some types of porcelain tile may require sealingprior to grouting to prevent possible staining. Use Aqua Mix® GroutRelease or TileLab® SurfaceGard® Sealer to prevent staining whenrequired.Color variation can occur due to tile type, tile porosity, jobsiteconditions, application and cleaning techniques. Variation can beminimized by following directions and using as little water as possiblefor cleanup.Chemicals in salt-based pool filtration systems can cause a reactionwith blue, green and red grouts. Contact Technical Services forrecommendations.

Packaging

Available in 3 sizes:

1 lb (.45 kg) tub7 lb (3.17 kg) box25 lb (11.34 kg) bag

25 lb bag and 7 lb box are available in 48 standard colors; colormatching is available. 1 lb grout is available in 4 colors.

4 Technical Data

Applicable Standards

American National Standards Institute (ANSI) ANSI A108.10 & A118.6of the American National Standards for the Installation of Ceramic TileASTM International (ASTM)

Polyblend® Sanded Grout

Published Date: 8/11/2014

Grout / TDS-129

ASTM C109 Standard Test Method for Compressive Strength ofHydraulic Cement Mortars (Using 2-in. or (50-mm) Cube Specimens)ASTM C531 Standard Test Method for Linear ShrinkageASTM C580 Standard Test method for Flexural StrengthISO 13007-3

Approvals

Polyblend® Sanded Grout exceeds ANSI A118.6 standards.

Technical Chart

Property Test Method Requirement Typical Results

Pot Life 1 - 2 HoursShrinkage A118.6

Section 4.3< 0.20% <0.08%

Water Absorption A118.6Section 4.4

< 10% <8%

28 Day CompressiveStrength

A118.6Section 4.5

> 3000 psi 4650 psi(327 kg/cm sq.)

Tensile Strength A118.6Section 4.6

> 300 psi 423 psi(29.7 kg/cm sq.)

Flexural Strength A118.6Section 4.7

> 500 psi 990 psi(69.6 kg/cm sq.)

Environmental Consideration

Custom® Building Products is committed to environmentalresponsibility in both products produced and in manufacturingpractices. Use of this product can contribute towards LEED® v3certification:

Up to 2 points towards MR Credit 5, Regional MaterialsUp to 1 point towards IEQ Credit 4.1, Low­Emitting Materials –

Adhesives & Sealants

5 Instructions

General Surface Prep

Tile or stone must be firmly bonded to a sound substrate, and settingmaterial must be cured a minimum 24-48 hours before cement groutis applied, unless rapid-setting mortars are used. See thecorresponding data sheet for the bonding mortars used in yourapplication. Remove spacers and ensure that the grout joints areuniform in depth and width and free of loose debris, contaminants andexcess mortar. Use TileLab® SurfaceGard® Sealer to seal tile orstone subject to staining or when using a grout that contrasts with thecolor of the tile.

Mixing Ratios

Mix 2 qt (1.89 L) clean water to 25 lb (11.34 kg) grout.Mix 1 pt (.473 mL) clean water to 7 lb (3.17 kg) grout.For 1 lb grout, see package for fill line indicator.

Mixing Procedures

Mix with a trowel or low speed mixer (less than 300 rpm) to achieve asmooth, lump-free consistency. Let the mixture stand (slake) for 10minutes, and then remix and use. Periodically remix to keep themixture workable, but do not add water, which can weaken the joint,cause color variation and possible cause shrinkage, cracks andpinholes. Discard grout when it becomes too stiff to work.

Application of Product

Installation must conform to ANSI A108.10. Lightly dampen absorptive,highly porous tile with clean, cool water, but leave no standing waterin the joints. Holding a rubber grout float at a 45° angle, completely fillthe joints. Holding the edge of the float at a 90° angle, remove excessgrout. At 70° F, do not spread more grout than can be cleaned within30 minutes of the grout firming and use as little water as possible forgrout clean-up. Using a damp, small pore grout sponge in a circularmotion, smooth and level joints and remove excess grout. Change thewater and rinse the sponge frequently. Haze can be removed after 3hours with cheesecloth or wrung-out sponge. If haze persists, theinstallation can be washed after three days with Aqua MixNanoScrub or after seven days with Aqua Mix® Sulfamic AcidCrystals or TileLab® Sulfamic Acid Cleaner. Perform a test in aninconspicuous area prior to complete application.

Curing of Product

Curing time is affected by ambient and surface temperatures andhumidity. For exterior applications, it is recommended that theinstallation is misted periodically with clean, cool water for 3 days.

Sealing of Grout

Use a pH-neutral sealer such as AquaMix Sealer's ChoiceGold or TileLab Surface Guard.

Cleaning of equipment

Clean tools and hands with water before the material dries.

Health Precautions

This product contains Portland cement. Avoid eye contact or prolongedcontact with skin. Wash thoroughly after handling. If eye contactoccurs, flush with water for 15 minutes and consult a physician. Usewith adequate ventilation; do not breathe dust and wear a NIOSHapproved respirator. If ingested, do not induce vomiting; call aphysician immediately.

Conformance to Building Codes

Installation must comply with the requirements of all applicable local,state and federal code jurisdictions.

Polyblend® Sanded Grout

Published Date: 8/11/2014

Grout / TDS-129

6 Availability & Cost

Location Color # Color Item Code Size Package Item Code Size Package

USA #9 Natural Gray PBG097­4   7 lb (3.17 kg) Box PBG0925 25 lb (11.34 kg) BagUSA #10 Antique White PBG107-4 7 lb (3.17 kg) Box PBG1025 25 lb (11.34 kg) BagUSA #11 Snow White PBG117-4 7 lb (3.17 kg) Box PBG1125 25 lb (11.34 kg) BagUSA #14 White Dove PBG147-4 7 lb (3.17 kg) Box PBG1425 25 lb (11.34 kg) BagUSA #17 Butter Cream PBG177-4 7 lb (3.17 kg) Box PBG1725 25 lb (11.34 kg) BagUSA #19 Pewter PBG197-4 7 lb (3.17 kg) Box PBG1925 25 lb (11.34 kg) BagUSA #22 Sahara Tan PBG227-4 7 lb (3.17 kg) Box PBG2225 25 lb (11.34 kg) BagUSA #35 Chaparral PBG357-4 7 lb (3.17 kg) Box PBG3525 25 lb (11.34 kg) BagUSA #45 Summer Wheat PBG457-4 7 lb (3.17 kg) Box PBG4525 25 lb (11.34 kg) BagUSA #50 Nutmeg PBG507-4 7 lb (3.17 kg) Box PBG5025 25 lb (11.34 kg) BagUSA #52 Tobacco Brown PBG527-4 7 lb (3.17 kg) Box PBG5225 25 lb (11.34 kg) BagUSA #59 Saddle Brown PBG597-4 7 lb (3.17 kg) Box PBG5925 25 lb (11.34 kg) BagUSA #60 Charcoal PBG607-4 7 lb (3.17 kg) Box PBG6025 25 lb (11.34 kg) BagUSA #90 Ocean Blue PBG907-4 7 lb (3.17 kg) Box PBG9025 25 lb (11.34 kg) BagUSA #92 Admiral Blue PBG927-4 7 lb (3.17 kg) Box PBG9225 25 lb (11.34 kg) BagUSA #95 Sable Brown PBG957-4 7 lb (3.17 kg) Box PBG9525 25 lb (11.34 kg) BagUSA #96 Quarry Red Clay PBG967-4 7 lb (3.17 kg) Box PBG9625 25 lb (11.34 kg) BagUSA #99 Burnt Clay PBG997-4 7 lb (3.17 kg) Box PBG9925 25 lb (11.34 kg) BagUSA #101 Quartz PBG1017-4 7 lb (3.17 kg) Box PBG10125 25 lb (11.34 kg) BagUSA #105 Earth PBG1057-4 7 lb (3.17 kg) Box PBG10525 25 lb (11.34 kg) BagUSA #115 Platinum PBG1157-4 7 lb (3.17 kg) Box PBG11525 25 lb (11.34 kg) BagUSA #122 Linen PBG1227-4 7 lb (3.17 kg) Box PBG12225 25 lb (11.34 kg) BagUSA #127 Antique Linen PBG1277-4 7 lb (3.17 kg) Box PBG12725 25 lb (11.34 kg) BagUSA #135 Mushroom PBG1357-4 7 lb (3.17 kg) Box PBG13525 25 lb (11.34 kg) BagUSA #145 Light Smoke PBG1457­4   7 lb (3.17 kg) Box PBG14525 25 lb (11.34 kg) BagUSA #156 Fawn PBG1567­4   7 lb (3.17 kg) Box PBG15625 25 lb (11.34 kg) BagUSA #165 Delorean Gray PBG1657­4   7 lb (3.17 kg) Box PBG16525 25 lb (11.34 kg) BagUSA #168 Slate Gray PBG1687­4   7 lb (3.17 kg) Box PBG16825 25 lb (11.34 kg) BagUSA #172 Urban Putty PBG1727­4   7 lb (3.17 kg) Box PBG17225 25 lb (11.34 kg) BagUSA #180 Sandstone PBG1807­4   7 lb (3.17 kg) Box PBG18025 25 lb (11.34 kg) BagUSA #183 Chateau PBG1837­4   7 lb (3.17 kg) Box PBG18325 25 lb (11.34 kg) BagUSA #185 New Taupe PBG1857­4   7 lb (3.17 kg) Box PBG18525 25 lb (11.34 kg) BagUSA #186 Khaki PBG1867­4   7 lb (3.17 kg) Box PBG18625 25 lb (11.34 kg) BagUSA #190 Bay Leaf PBG1907­4   7 lb (3.17 kg) Box PBG19025 25 lb (11.34 kg) BagUSA #301 Arctic Ice PBG3017­4   7 lb (3.17 kg) Box PBG30125 25 lb (11.34 kg) BagUSA #305 Onyx Green PBG3057­4   7 lb (3.17 kg) Box PBG30525 25 lb (11.34 kg) BagUSA #311 Moss PBG3117­4   7 lb (3.17 kg) Box PBG31125 25 lb (11.34 kg) BagUSA #312 Bonsai PBG3127­4   7 lb (3.17 kg) Box PBG31225 25 lb (11.34 kg) BagUSA #333 Alabaster PBG3337­4   7 lb (3.17 kg) Box PBG33325 25 lb (11.34 kg) BagUSA #335 Winter Gray PBG3357­4   7 lb (3.17 kg) Box PBG33525 25 lb (11.34 kg) BagUSA #365 Canvas PBG3657­4   7 lb (3.17 kg) Box PBG36525 25 lb (11.34 kg) BagUSA #370 Dove Gray PBG3707­4   7 lb (3.17 kg) Box PBG37025 25 lb (11.34 kg) Bag

Polyblend® Sanded Grout

Published Date: 8/11/2014

Grout / TDS-129

Location Color # Color Item Code Size Package Item Code Size Package

USA #380 Haystack PBG3807­4   7 lb (3.17 kg) Box PBG38025 25 lb (11.34 kg) BagUSA #381 Bright White PBG3817­4   7 lb (3.17 kg) Box PBG38125 25 lb (11.34 kg) BagUSA #382 Bone PBG3827­4   7 lb (3.17 kg) Box PBG38225 25 lb (11.34 kg) BagUSA #384 Camel PBG3847­4   7 lb (3.17 kg) Box PBG38425 25 lb (11.34 kg) BagUSA #386 Oyster Gray PBG3867­4   7 lb (3.17 kg) Box PBG38625 25 lb (11.34 kg) BagUSA #390 Rose Beige PBG3907­4   7 lb (3.17 kg) Box PBG39025 25 lb (11.34 kg) BagUSA - Special Order All 48 colors PBGXXX50   50 lb (22.68 kg) Bag Canada #9 Natural Gray CPBG097­4   7 lb (3.17 kg) Box CPBG0925 25 lb (11.34 kg) BagCanada #10 Antique White CPBG107-4 7 lb (3.17 kg) Box CPBG1025 25 lb (11.34 kg) BagCanada #11 Snow White CPBG117-4 7 lb (3.17 kg) Box CPBG1125 25 lb (11.34 kg) BagCanada #14 White Dove CPBG147-4 7 lb (3.17 kg) Box CPBG1425 25 lb (11.34 kg) BagCanada #17 Butter Cream CPBG177-4 7 lb (3.17 kg) Box CPBG1725 25 lb (11.34 kg) BagCanada #19 Pewter CPBG197-4 7 lb (3.17 kg) Box CPBG1925 25 lb (11.34 kg) BagCanada #22 Sahara Tan CPBG227-4 7 lb (3.17 kg) Box CPBG2225 25 lb (11.34 kg) BagCanada #35 Chaparral CPBG357-4 7 lb (3.17 kg) Box CPBG3525 25 lb (11.34 kg) BagCanada #45 Summer Wheat CPBG457-4 7 lb (3.17 kg) Box CPBG4525 25 lb (11.34 kg) BagCanada #50 Nutmeg CPBG507-4 7 lb (3.17 kg) Box CPBG5025 25 lb (11.34 kg) BagCanada #52 Tobacco Brown CPBG527-4 7 lb (3.17 kg) Box CPBG5225 25 lb (11.34 kg) BagCanada #59 Saddle Brown CPBG597-4 7 lb (3.17 kg) Box CPBG5925 25 lb (11.34 kg) BagCanada #60 Charcoal CPBG607-4 7 lb (3.17 kg) Box CPBG6025 25 lb (11.34 kg) BagCanada #90 Ocean Blue CPBG907-4 7 lb (3.17 kg) Box CPBG9025 25 lb (11.34 kg) BagCanada #92 Admiral Blue CPBG927-4 7 lb (3.17 kg) Box CPBG9225 25 lb (11.34 kg) BagCanada #95 Sable Brown CPBG957-4 7 lb (3.17 kg) Box CPBG9525 25 lb (11.34 kg) BagCanada #96 Quarry Red Clay CPBG967-4 7 lb (3.17 kg) Box CPBG9625 25 lb (11.34 kg) BagCanada #99 Burnt Clay CPBG997-4 7 lb (3.17 kg) Box CPBG9925 25 lb (11.34 kg) BagCanada #101 Quartz CPBG1017-4 7 lb (3.17 kg) Box CPBG10125 25 lb (11.34 kg) BagCanada #105 Earth CPBG1057-4 7 lb (3.17 kg) Box CPBG10525 25 lb (11.34 kg) BagCanada #115 Platinum CPBG1157-4 7 lb (3.17 kg) Box CPBG11525 25 lb (11.34 kg) BagCanada #122 Linen CPBG1227-4 7 lb (3.17 kg) Box CPBG12225 25 lb (11.34 kg) BagCanada #127 Antique Linen CPBG1277-4 7 lb (3.17 kg) Box CPBG12725 25 lb (11.34 kg) BagCanada #135 Mushroom CPBG1357-4 7 lb (3.17 kg) Box CPBG13525 25 lb (11.34 kg) BagCanada #145 Light Smoke CPBG1457­4   7 lb (3.17 kg) Box CPBG14525 25 lb (11.34 kg) BagCanada #156 Fawn CPBG1567­4   7 lb (3.17 kg) Box CPBG15625 25 lb (11.34 kg) BagCanada #165 Delorean Gray CPBG1657­4   7 lb (3.17 kg) Box CPBG16525 25 lb (11.34 kg) BagCanada #168 Slate Gray CPBG1687­4   7 lb (3.17 kg) Box CPBG16825 25 lb (11.34 kg) BagCanada #172 Urban Putty CPBG1727­4   7 lb (3.17 kg) Box CPBG17225 25 lb (11.34 kg) BagCanada #180 Sandstone CPBG1807­4   7 lb (3.17 kg) Box CPBG18025 25 lb (11.34 kg) BagCanada #183 Chateau CPBG1837­4   7 lb (3.17 kg) Box CPBG18325 25 lb (11.34 kg) BagCanada #185 New Taupe CPBG1857­4   7 lb (3.17 kg) Box CPBG18525 25 lb (11.34 kg) BagCanada #186 Khaki CPBG1867­4   7 lb (3.17 kg) Box CPBG18625 25 lb (11.34 kg) BagCanada #190 Bay Leaf CPBG1907­4   7 lb (3.17 kg) Box CPBG19025 25 lb (11.34 kg) BagCanada #301 Arctic Ice CPBG3017­4   7 lb (3.17 kg) Box CPBG30125 25 lb (11.34 kg) BagCanada #305 Onyx Green CPBG3057­4   7 lb (3.17 kg) Box CPBG30525 25 lb (11.34 kg) BagCanada #311 Moss CPBG3117­4   7 lb (3.17 kg) Box CPBG31125 25 lb (11.34 kg) Bag

Polyblend® Sanded Grout

Published Date: 8/11/2014

Grout / TDS-129

Location Color # Color Item Code Size Package Item Code Size Package

Canada #312 Bonsai CPBG3127­4   7 lb (3.17 kg) Box CPBG31225 25 lb (11.34 kg) BagCanada #333 Alabaster CPBG3337­4   7 lb (3.17 kg) Box CPBG33325 25 lb (11.34 kg) BagCanada #335 Winter Gray CPBG3357­4   7 lb (3.17 kg) Box CPBG33525 25 lb (11.34 kg) BagCanada #365 Canvas CPBG3657­4   7 lb (3.17 kg) Box CPBG36525 25 lb (11.34 kg) BagCanada #370 Dove Gray CPBG3707­4   7 lb (3.17 kg) Box CPBG37025 25 lb (11.34 kg) BagCanada #380 Haystack CPBG3807­4   7 lb (3.17 kg) Box CPBG38025 25 lb (11.34 kg) BagCanada #381 Bright White CPBG3817­4   7 lb (3.17 kg) Box CPBG38125 25 lb (11.34 kg) BagCanada #382 Bone CPBG3827­4   7 lb (3.17 kg) Box CPBG38225 25 lb (11.34 kg) BagCanada #384 Camel CPBG3847­4   7 lb (3.17 kg) Box CPBG38425 25 lb (11.34 kg) BagCanada #386 Oyster Gray CPBG3867­4   7 lb (3.17 kg) Box CPBG38625 25 lb (11.34 kg) BagCanada #390 Rose Beige CPBG3907­4   7 lb (3.17 kg) Box CPBG39025 25 lb (11.34 kg) Bag

Location Color # Color Item Code Size Package

USA #9 Natural Gray PBG-091-4 1 lb TubUSA #122 Linen PBG-1221-4 1 lb TubUSA #380 Haystack PBG-3801-4 1 lb TubUSA #382 Bone PBG-3821-4 1 lb Tub

7 Product Warranty

Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship undernormal and proper usage for a period of one year following the date of original purchase. Custom's® sole liability under this warranty shall be limited tothe replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, sothe above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has notbeen used in accordance with Custom's® printed instructions. Custom® makes no other warranties either expressed or implied. This warranty gives youspecific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. This warranty is nottransferrable.

8 Product Maintenance

Clean with a neutral cleaner such as Aqua Mix AquaKleen, Aqua Mix Concentrated Tile & Stone Cleaner or TileLab Grout & Tile Cleaner.

9 Technical Services Information

For technical assistance, contact Custom® technical services at 800­272­8786 or visit custombuildingproducts.com.

10 Filing System

Additional product information is available from the manufacturer upon request.

Related Products

Polyblend® Ceramic Tile Caulk

Commercial 100% Silicone Caulk

TileLab® SurfaceGard® Sealer

StainBlocker for Grout

Polyblend® Non­Sanded Grout

Polyblend® Sanded Grout

Published Date: 8/11/2014

Grout / TDS-129

Coverage

Coverage will vary depending on the tile size and joint width. Chart based on 25 lb (11.34 kg) bag.

Joint Width

Tile Size 1/8" (3 mm) 3/16" (4.5 mm) 1/4" (6 mm) 3/8" (9.5 mm) 1/2" (13 mm)

1" x 1" x 1/4" (25 x 25 x 6 mm) 63 ft² (5.9 M²) 40 ft² (3.7 M²) 25 ft² (2.3 M²) 23 ft² (2.1 M²) 20 ft² (1.9 M²)

2" x 2" x 1/4" (50 x 50 x 6 mm) 88 ft² (8.2 M²) 73 ft² (6.8 M²) 50 ft² (4.6 M²) 40 ft² (3.7 M²) 33 ft² (3.1 M²)

3" x 3" x 1/4" (75 x 75 x 6 mm) 150 ft² (14.0 M²) 103 ft² (9.6 M²) 80 ft² (7.4 M²) 55 ft² (5.1 M²) 45 ft² (4.2 M²)

4 1/4" x 4 1/4" x 1/4" (108 x 108 x 6 mm) 210 ft² (19.5 M²) 143 ft² (13.3 M²) 110 ft² (10.2 M²) 75 ft² (7.0 M²) 60 ft² (5.6 M²)

6" x 6" x 1/4" (150 x 150 x 6 mm) 263 ft² (24.4 M²) 178 ft² (16.5 M²) 136 ft² (12.6 M²) 93 ft² (8.6 M²) 70 ft² (6.5 M²)

8" x 8" x 3/8" (200 x 200 x 9.5 mm) 230 ft² (21.4 M²) 155 ft² (14.4 M²) 113 ft² (10.5 M²) 75 ft² (7.0 M²) 50 ft² (4.6 M²)

12" x 12" x 3/8" (300 x 300 x 9.5 mm) 345 ft² (32.1 M²) 230 ft² (21.4 M²) 175 ft² (16.3 M²) 118 ft² (11.0 M²) 90 ft² (8.4 M²)

16" x 16" x 3/8" (400 x 400 x 9.5 mm) 458 ft² (42.5 M²) 305 ft² (28.3 M²) 225 ft² (20.9 M²) 144 ft² (13.4 M²) 94 ft² (8.7 M²)

18" x 18" x 3/8" (450 x 450 x 9.5 mm) 512 ft² (47.5 M²) 343 ft² (31.9 M²) 253 ft² (23.5 M²) 167 ft² (15.5 M²) 118 ft² (11 M²)

20" x 20" x 3/8" (500 x 500 x 9.5 mm) 567 ft² (52.7 M²) 381 ft² (35.4 M²) 280 ft² (26.0 M²) 189 ft² (17.6 M²) 142 ft² (13.2 M²)

24" x 24" x 3/8" (600 x 600 x 9.5 mm) 685 ft² (63.6 M²) 458 ft² (42.5 M²) 325 ft² (30.2 M²) 225 ft² (20.9 M²) 150 ft² (13.9 M²)

Polyblend® Sanded Grout

Published Date: 8/11/2014

TILING 09 30 00 Grout / TDS-130

1 Product Name

Polyblend® Non­Sanded Grout

2 Manufacturer

Custom Building Products13001 Seal Beach Blvd.Seal Beach, CA 90740-2757Customer Support: 800-272-8786Technical Services: 800-282-8786Fax: 800- 200-7765Email: contactus@cbpmail.netcustombuildingproducts.com

3 Product Description

A polymer-modified grout designed for highly glazed or polished tile,marble and natural stone that would be scratched by sanded grouts.This durable, non-shrinking grout accommodates joints to 1/8" (3 mm)and can be used for interior or exterior installations, including floors,countertops, walls, ceilings, showers, fountains and pools.

Suitable Tile Types

Vitreous, semi-vitreous or non-vitreous tile: ceramic, mosaic, quarry,cement body tileImpervious porcelain and glass tileBrick and stone veneerCement-based precast terrazzoNatural stone tile

Composition of Product

Polyblend® Non­Sanded Grout is a dry, Portland cement based grout,inorganic aggregates and chemicals.

Benefits of Product in the Installation

Consistent colorExcellent for highly-glazed ceramic tile and highly-polished marble ornatural stoneResists shrinking, cracking, powdering and wearExceeds ANSI A118.6 standardsRated for residential to extra-heavy commercial use

Limitations to the Product

Should not be installed when ambient surface temperature is lowerthan 50°F (10°C) or higher than 100°F (38°C).

Some ceramic tile, marble or stone can be scratched, stained ordamaged by sanded or pigmented grout. White grout is generally bestfor light-colored marble or granite. Test a small area prior to use.Polyblend® Non-Sanded Groutmay be appropriate for tile not suitable for sanded grout.Tile with high absorption, surface porosity or rough, textured surfacesand certain types of porcelain may require sealing prior to grouting toprevent staining. UseTilelab® SurfaceGard® Sealerto prevent grout staining, when required.Color variation can occur due to tile type, tile porosity, jobsiteconditions, application and cleaning techniques. Variation can beminimized by following directions and using as little water as possiblefor cleanup.Chemicals in salt-based pool filtration systems can cause a reactionwith blue, green and red grouts. Contact Technical Services forrecommendations.

Packaging

Available in 2 sizes:

10 lb (4.5 kg) box

25 lb (11.34 kg) bag

Available in 48 standard colors; color matching is available.

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Grout / TDS-130

4 Technical Data

Applicable Standards

American National Standards Institute (ANSI) ANSI A108.10 andA118.6 American National Standards for the Installation of CeramicTile ASTM International (ASTM)

ASTM C109 Standard Test Method for Compressive Strength ofHydraulic Cement Mortars (Using 2-in. or (50-mm) Cube Specimens)ASTM C531 Standard Test Method for Linear ShrinkageASTM C580 Standard Test method for Flexural Strength

Resilient Floor Covering Institute (RFCI) Recommended Work Practicesfor Removal of Resilient Floor Coverings.

Tile Council of North America (TCNA) TCNA Handbook for Ceramic TileInstallation, TCNA Method EJ171

Approvals

Polyblend® Non­Sanded Grout meets or exceeds ANSI A118.6standards.

Technical Chart

Property Test

Method

Requirement Typical Results

Cement Grouts Non-Sanded Standard Pot Life 1-2 hoursShrinkage A118.6

Section 4.3< 0.30% <0.10%

WaterAbsorption

A118.6Section 4.4

< 18% <16%

28 DayCompressiveStrength

A118.6Section 4.5

> 3000 psi 3300 psi(232 kg/cm sq.)

TensileStrength

A118.6Section 4.6

> 250 psi 525 psi(36.9 kg/cm sq.)

FlexuralStrength

A118.6Section 4.7

>500 psi >790 psi(>55.6 kg/cm sq.)

Environmental Consideration

Custom® Building Products is committed to environmentalresponsibility in both products produced and in manufacturingpractices. Use of this product may contribute to LEED® certification.

5 Instructions

General Surface Prep

Tile or stone must be firmly bonded to a sound substrate, and settingmaterial must be cured a minimum 24-48 hours before cement groutis applied, unless rapid-setting mortars are used. See thecorresponding data for the bonding mortars used in your application.Remove spacers and ensure that the grout joints are uniform in depthand width and free of loose debris, contaminants and excess mortar.Use TileLab® SurfaceGard® Sealer to seal tile or stone subject tostaining.

Mixing Ratios - powder to water

Mix 3 pt (1.4 L) clean water to 10 lb (4.5 kg) grout.

Mixing Procedures

Mix with a trowel or low speed mixer (less than 300 rpm) to achieve asmooth, lump-free consistency. Let the mixture stand (slake) for 10minutes, and then remix and use. Periodically remix to keep themixture workable, but do not add water, which can weaken the joint,cause color variation and possible cause shrinkage, cracks andpinholes. Discard grout when it becomes too stiff to work.

Application of Product

Installation must confirm to ANSI A108.10. Lightly dampen absorptive,highly porous tile with clean, cool water, but leave no standing waterin the joints. Holding a rubber grout float at a 45° angle, completely fillthe joints. Holding the edge of the float at a 90° angle, remove excessgrout. Do not spread more grout than can be cleaned within 30minutes of the grout firming and use as little water as possible forgrout clean-up. Using a damp, small pore grout sponge in a circularmotion, smooth and level joints and remove excess grout. Change thewater and rinse the sponge frequently. Haze can be removed after 3hours with cheesecloth or wrung-out sponge. If haze persists, theinstallation can be acid-washed after 72 hours with a suitable dilutedacid.

Curing of Product

Curing time is affected by ambient and surface temperatures andhumidity. Use the following as a guideline. Periodically misting theinstallation with clean, cool water for 3 days is recommended.

Sealing of Grout

Use a pH neutral sealer such as TileLab Surface Guard or AquaMixSealers Choice.

Cleaning of equipment

Clean tools and hands with water before the material dries.

Health Precautions

This product contains Portland cement. Avoid eye contact or prolongedcontact with skin. Wash thoroughly after handling. If eye contactoccurs, flush with water for 15 minutes and consult a physician. Usewith adequate ventilation; do not breathe dust and wear a NIOSHapproved respirator. If ingested, do not induce vomiting; call aphysician immediately.

Conformance to Building Codes

Installation must comply with the requirements of all applicable local,state and federal code jurisdictions.

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Grout / TDS-130

6 Availability & Cost

Location Color # Color Item Code Size Package Item Code Size Package

USA #9 Natural Gray PBG0910 10 lb (4.5 kg) Box NSG0925* 25 lb (11.34 kg) BagUSA #10 Antique White PBG1010 10 lb (4.5 kg) Box NSG1025** 25 lb (11.34 kg) BagUSA #11 Snow White PBG1110 10 lb (4.5 kg) Box NSG1125** 25 lb (11.34 kg) BagUSA #14 White Dove PBG1410 10 lb (4.5 kg) Box NSG1425* 25 lb (11.34 kg) BagUSA #17 Butter Cream PBG1710 10 lb (4.5 kg) Box NSG1725* 25 lb (11.34 kg) BagUSA #19 Pewter PBG1910 10 lb (4.5 kg) Box NSG1925* 25 lb (11.34 kg) BagUSA #22 Sahara Tan PBG2210 10 lb (4.5 kg) Box NSG2225* 25 lb (11.34 kg) BagUSA #35 Chaparral PBG3510 10 lb (4.5 kg) Box NSG3525* 25 lb (11.34 kg) BagUSA #45 Summer Wheat PBG4510 10 lb (4.5 kg) Box NSG3525* 25 lb (11.34 kg) BagUSA #50 Nutmeg PBG5010 10 lb (4.5 kg) Box NSG5025* 25 lb (11.34 kg) BagUSA #52 Tobacco Brown PBG5210 10 lb (4.5 kg) Box NSG5225* 25 lb (11.34 kg) BagUSA #59 Saddle Brown PBG5910 10 lb (4.5 kg) Box NSG5925* 25 lb (11.34 kg) BagUSA #60 Charcoal PBG6010 10 lb (4.5 kg) Box NSG6025* 25 lb (11.34 kg) BagUSA #90 Ocean Blue PBG9010 10 lb (4.5 kg) Box NSG9025* 25 lb (11.34 kg) BagUSA #92 Admiral Blue PBG9210 10 lb (4.5 kg) Box NSG9225* 25 lb (11.34 kg) BagUSA #95 Sable Brown PBG9510 10 lb (4.5 kg) Box NSG9525* 25 lb (11.34 kg) BagUSA #96 Quarry Red Clay PBG9610 10 lb (4.5 kg) Box NSG9625* 25 lb (11.34 kg) BagUSA #99 Burnt Clay PBG9910 10 lb (4.5 kg) Box NSG9925* 25 lb (11.34 kg) BagUSA #101 Quartz PBG10110 10 lb (4.5 kg) Box NSG10125* 25 lb (11.34 kg) BagUSA #105 Earth PBG10510 10 lb (4.5 kg) Box NSG10525* 25 lb (11.34 kg) Bag

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Grout / TDS-130

Location Color # Color Item Code Size Package Item Code Size PackageUSA #115 Platinum PBG11510 10 lb (4.5 kg) Box NSG11525* 25 lb (11.34 kg) BagUSA #122 Linen PBG12210 10 lb (4.5 kg) Box NSG12225*** 25 lb (11.34 kg) BagUSA #127 Antique Linen PBG12710 10 lb (4.5 kg) Box NSG12725* 25 lb (11.34 kg) BagUSA #135 Mushroom PBG13510 10 lb (4.5 kg) Box NSG13525* 25 lb (11.34 kg) BagUSA #145 Light Smoke PBG14510    10 lb (4.5 kg) Box NSG14525* 25 lb (11.34 kg) BagUSA #156 Fawn PBG15610   10 lb (4.5 kg) Box NSG15625* 25 lb (11.34 kg) BagUSA #165 Delorean Gray PBG16510    10 lb (4.5 kg) Box NSG16525*** 25 lb (11.34 kg) BagUSA #168 Slate Gray PBG16810    10 lb (4.5 kg) Box NSG16825* 25 lb (11.34 kg) BagUSA #172 Urban Putty PBG17210    10 lb (4.5 kg) Box NSG17225 25 lb (11.34 kg) BagUSA #180 Sandstone PBG18010    10 lb (4.5 kg) Box NSG18025* 25 lb (11.34 kg) BagUSA #183 Chateau PBG18310   10 lb (4.5 kg) Box NSG18325* 25 lb (11.34 kg) BagUSA #185 New Taupe PBG18510   10 lb (4.5 kg) Box NSG18525* 25 lb (11.34 kg) BagUSA #186 Khaki PBG18610   10 lb (4.5 kg) Box NSG18625* 25 lb (11.34 kg) BagUSA #190 Bay Leaf PBG19010    10 lb (4.5 kg) Box NSG19025* 25 lb (11.34 kg) BagUSA #301 Arctic Ice PBG30110    10 lb (4.5 kg) Box NSG30125* 25 lb (11.34 kg) BagUSA #305 Onyx Green PBG30510    10 lb (4.5 kg) Box NSG30525* 25 lb (11.34 kg) BagUSA #311 Moss PBG31110    10 lb (4.5 kg) Box NSG31125* 25 lb (11.34 kg) BagUSA #312 Bonsai PBG31210    10 lb (4.5 kg) Box NSG31225* 25 lb (11.34 kg) BagUSA #333 Alabaster PBG33310   10 lb (4.5 kg) Box NSG33325* 25 lb (11.34 kg) BagUSA #335 Winter Gray PBG33510    10 lb (4.5 kg) Box NSG33525*** 25 lb (11.34 kg) BagUSA #365 Canvas PBG36510    10 lb (4.5 kg) Box NSG36525*** 25 lb (11.34 kg) BagUSA #370 Dove Gray PBG37010   10 lb (4.5 kg) Box NSG37025* 25 lb (11.34 kg) BagUSA #380 Haystack PBG38010   10 lb (4.5 kg) Box NSG38025*** 25 lb (11.34 kg) BagUSA #381 Bright White PBG38110   10 lb (4.5 kg) Box NSG38125** 25 lb (11.34 kg) BagUSA #382 Bone PBG38210   10 lb (4.5 kg) Box NSG38225** 25 lb (11.34 kg) BagUSA #384 Camel PBG38410   10 lb (4.5 kg) Box NSG38425* 25 lb (11.34 kg) BagUSA #386 Oyster Gray PBG38610   10 lb (4.5 kg) Box NSG38625* 25 lb (11.34 kg) BagUSA #390 Rose Beige PBG39010   10 lb (4.5 kg) Box NSG39025* 25 lb (11.34 kg) Bag Canada #9 Natural Gray CPBG0910N  10 lb (4.5 kg) Box CNSG0925N* 25 lb (11.34 kg) BagCanada #10 Antique White CPBG1010N 10 lb (4.5 kg) Box CNSG1025N* 25 lb (11.34 kg) BagCanada #11 Snow White CPBG1110N 10 lb (4.5 kg) Box CBPWDG25* 25 lb (11.34 kg) BagCanada #14 White Dove CPBG1410N 10 lb (4.5 kg) Box CNSG1425N* 25 lb (11.34 kg) BagCanada #17 Butter Cream CPBG1710N 10 lb (4.5 kg) Box CNSG1725N* 25 lb (11.34 kg) BagCanada #19 Pewter CPBG1910N 10 lb (4.5 kg) Box CNSG1925N* 25 lb (11.34 kg) BagCanada #22 Sahara Tan CPBG2210N 10 lb (4.5 kg) Box CNSG2225N* 25 lb (11.34 kg) BagCanada #35 Chaparral CPBG3510N 10 lb (4.5 kg) Box CNSG3525N* 25 lb (11.34 kg) BagCanada #45 Summer Wheat CPBG4510N 10 lb (4.5 kg) Box CNSG4525N* 25 lb (11.34 kg) BagCanada #50 Nutmeg CPBG5010N 10 lb (4.5 kg) Box CNSG5025N* 25 lb (11.34 kg) BagCanada #52 Tobacco Brown CPBG5210N 10 lb (4.5 kg) Box CNSG5225N* 25 lb (11.34 kg) Bag

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Grout / TDS-130

Location Color # Color Item Code Size Package Item Code Size PackageCanada #59 Saddle Brown CPBG5910N 10 lb (4.5 kg) Box CNSG5925N* 25 lb (11.34 kg) BagCanada #60 Charcoal CPBG6010N 10 lb (4.5 kg) Box CNSG6025N* 25 lb (11.34 kg) BagCanada #90 Ocean Blue CPBG9010N 10 lb (4.5 kg) Box CNSG9025N* 25 lb (11.34 kg) BagCanada #92 Admiral Blue CPBG9210N 10 lb (4.5 kg) Box CNSG9225N* 25 lb (11.34 kg) BagCanada #95 Sable Brown CPBG9510N 10 lb (4.5 kg) Box CNSG9525N* 25 lb (11.34 kg) BagCanada #96 Quarry Red Clay CPBG9610N 10 lb (4.5 kg) Box CNSG9625N* 25 lb (11.34 kg) BagCanada #99 Burnt Clay CPBG9910N 10 lb (4.5 kg) Box CNSG9925N* 25 lb (11.34 kg) BagCanada #101 Quartz CPBG10110N 10 lb (4.5 kg) Box CNSG10125N* 25 lb (11.34 kg) BagCanada #105 Earth CPBG10510N 10 lb (4.5 kg) Box CNSG10525N* 25 lb (11.34 kg) BagCanada #115 Platinum CPBG11510N 10 lb (4.5 kg) Box CNSG11525N* 25 lb (11.34 kg) BagCanada #122 Linen CPBG12210N 10 lb (4.5 kg) Box CNSG12225N* 25 lb (11.34 kg) BagCanada #127 Antique Linen CPBG12710N 10 lb (4.5 kg) Box CNSG12725N* 25 lb (11.34 kg) BagCanada #135 Mushroom CPBG13510N 10 lb (4.5 kg) Box CNSG13525N* 25 lb (11.34 kg) BagCanada #145 Light Smoke CPBG14510N   10 lb (4.5 kg) Box CNSG14525N* 25 lb (11.34 kg) BagCanada #156 Fawn CPBG15610N  10 lb (4.5 kg) Box CNSG15625N* 25 lb (11.34 kg) BagCanada #165 Delorean Gray CPBG16510N   10 lb (4.5 kg) Box CNSG16525N* 25 lb (11.34 kg) BagCanada #168 Slate Gray CPBG16810N   10 lb (4.5 kg) Box CNSG16825N* 25 lb (11.34 kg) BagCanada #172 Urban Putty CPBG17210N  10 lb (4.5 kg) Box CNSG17225N* 25 lb (11.34 kg) BagCanada #180 Sandstone CPBG18010N   10 lb (4.5 kg) Box CNSG18025N* 25 lb (11.34 kg) BagCanada #183 Chateau CPBG18310N  10 lb (4.5 kg) Box CNSG18325N* 25 lb (11.34 kg) BagCanada #185 New Taupe CPBG18510N   10 lb (4.5 kg) Box CNSG18525N* 25 lb (11.34 kg) BagCanada #186 Khaki CPBG18610N   10 lb (4.5 kg) Box CNSG18625N* 25 lb (11.34 kg) BagCanada #190 Bay Leaf CPBG19010N   10 lb (4.5 kg) Box CNSG19025N* 25 lb (11.34 kg) BagCanada #301 Arctic Ice CPBG30110N  10 lb (4.5 kg) Box CNSG30125N* 25 lb (11.34 kg) BagCanada #305 Onyx Green CPBG30510N   10 lb (4.5 kg) Box CNSG30525N* 25 lb (11.34 kg) BagCanada #311 Moss CPBG31110N   10 lb (4.5 kg) Box CNSG31125N* 25 lb (11.34 kg) BagCanada #312 Bonsai CPBG31210N   10 lb (4.5 kg) Box CNSG31225N* 25 lb (11.34 kg) BagCanada #333 Alabaster CPBG33310N   10 lb (4.5 kg) Box CNSG33325N* 25 lb (11.34 kg) BagCanada #335 Winter Gray CPBG33510N   10 lb (4.5 kg) Box CNSG33525N* 25 lb (11.34 kg) BagCanada #365 Canvas CPBG36510N  10 lb (4.5 kg) Box CNSG36525N* 25 lb (11.34 kg) BagCanada #370 Dove Gray CPBG37010N  10 lb (4.5 kg) Box CNSG37025N* 25 lb (11.34 kg) BagCanada #380 Haystack CPBG38010N  10 lb (4.5 kg) Box CNSG38025N* 25 lb (11.34 kg) BagCanada #381 Bright White CPBG38110N 10 lb (4.5 kg) Box CNSG38125N* 25 lb (11.34 kg) BagCanada #382 Bone CPBG38210N  10 lb (4.5 kg) Box CNSG38225N* 25 lb (11.34 kg) BagCanada #384 Camel CPBG38410N  10 lb (4.5 kg) Box CNSG38425N* 25 lb (11.34 kg) BagCanada #386 Oyster Gray CPBG38610N   10 lb (4.5 kg) Box CNSG38625N* 25 lb (11.34 kg) BagCanada #390 Rose Beige CPBG39010N   10 lb (4.5 kg) Box CNSG39025N* 25 lb (11.34 kg) Bag

* Indicates special order item.

** Available from Georgia, Indiana and New Jersey plants only.

*** Available from Georgia plant only.

7 Product Warranty

Custom® Building Products warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship undernormal and proper usage for a period of one year following the date of original purchase. Custom's® sole liability under this warranty shall be limited tothe replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental or consequential damages, sothe above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has notbeen used in accordance with Custom's® printed instructions. Custom® makes no other warranties either expressed or implied. This warranty gives youspecific legal rights, and you may have other rights that vary from state to state or from one country/territory to another. Click for details and completewarranty information.

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Grout / TDS-130

8 Product Maintenance

Clean with a neutral cleaner such as AquaMix AquaKleen or TilelabGrout & Tile Cleaner

9 Technical Services Information

For technical assistance, contact Custom® Building Products.

10 Filing System

Additional product information is available from the manufacturer uponrequest.

Related Products

Polyblend® Ceramic Tile Caulk

Commercial 100% Silicone Caulk

TileLab® SurfaceGard® Sealer

StainBlocker for Grout

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Grout / TDS-130

Coverage

Joint Width

Tile Size 1/16" (3 mm) 1/8" (3 mm)

1" x 1" x 1/4" (25 x 25 x 6 mm) 44 (4.1) 20 (1.9)2" x 2" x 1/4" (50 x 50 x 6 mm) 85 (7.9) 40 (3.7)3" x 3" x 1/4" (75 x 75 x 6 mm) 126 (11.7) 60 (5.6)4 1/4" x 4 1/4" x 1/4" (108 x 108 x 6 mm) 149 (13.8) 78 (7.2)6" x 6" x 1/4" (150 x 150 x 6 mm) 250 (23.2) 120 (11.1)8" x 8" x 3/8" (200 x 200 x 9.5 mm) 220 (20.4) 110 (10.2)12" x 12" x 3/8" (300 x 300 x 9.5 mm) 331 (30.1) 171 (15.9)16" x 16" x 3/8" (400 x 400 x 9.5 mm) 370 (34.4) 185 (17.2)20" x 20" x 3/8" (500 x 500 x 9.5 mm) 453 (42.1) 227 (21.1)24" x 24" x 3/8" (600 x 600 x 9.5 mm) 659 (61.2) 330 (30.7)

Polyblend® Non­Sanded Grout

Published Date: April 22 2013

TILING 09 30 00 Aqua Mix® / TDS­157

1 Product Name

Aqua Mix® Penetrating Sealer

2 Manufacturer

Custom Building Products13001 Seal Beach Blvd.Seal Beach, CA 90740-2757Customer Support: 800-272-8786Technical Services: 800-282-8786Fax: 800- 200-7765Email: contactus@cbpmail.netcustombuildingproducts.com

3 Product Description

An economical, no-sheen, natural look, water-based, penetratingsealer designed to resist stains. May also be used as a pre-groutingsealer. Allows moisture vapor transmission. Can be used as a groutsealer.

Suitable Tile Types

As a sealer or grout release for all natural stone surfaces, unglazedtile, porcelain, clay pavers, concrete, brick, masonry, and grout. Forinterior and exterior use.

Limitations to the Product

Do not allow product to come in contact with any non-recommendedsurfaceIf product is allowed to dry on surface, a white film may form. If thisoccurs, scrub surface with water and a white nylon padSealer will not prevent surface wear or etching from acids or causticchemicalsNote: Aqua Mix® Ultra­Solv® or Sealer's Choice® Gold Rapid Cure

Formula are recommended in place of Penetrating Sealer in foodpreparation areas or where maximum stain protection is required

4 Technical Data

Technical Properties Chart

Complies with all Federal EPA and SCAQMD standards for VOC

Technical Chart

Property Test Method Requirement Typical Results

Stain Resistance CTI-072 n/a Very GoodpH n/aDarken Stone NoCure Time 24 hoursExpected Wear Up to 5 years

5 Instructions

General Surface Prep

Surface should be dry, clean and free of waxes, sealers or finishes.New installations need to dry 48 hours before application. Protectpainted surfaces. Test product in obscure area to ensure desirableresults.

Application of Product

Read entire label before using. Apply liberally using a new mop, paintpad applicator, sponge or brush. Allow it to penetrate for up to 5minutes. Wipe surface completely dry using clean, dry cotton or papertowels after each application. Porous surfaces may require additionalapplications. Conduct a test to see if surface is completely sealed after2 hours by applying drops of water on the surface. If it penetrates,apply an additional coat. If a residue is visible on the surface afterdrying, remove it with water and a white nylon scrub pad 60 minutesafter application.

Pre-Grout Sealer/Grout Release

Porous tile, such as clay and Saltillo pavers, can be stained by groutduring installation. Sealing the tile before grouting will make groutremoval much easier. Apply two coats of sealer according to directionsafter tile has been bonded for a minimum of 24 hours, or apply to frontface of tile before installation.

Drying Time

Allow 30 minutes drying time between coats.Ready for surface traffic in 2 hours.Keep dry for 12 hours.Achieves a full cure in 24 hours.

Cleaning of equipment

Clean tools and hands with soap and water immediately after use.

Health Precautions

MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN.Wear skin and eye protection. Do not breathe vapor or spray. Containspotassium methyl siliconate. If in eyes, flush with water for at least 15minutes. If on skin, wash with soap and water. If respiratory tract isirritated, remove to fresh air. If irritation persists, seek medicalattention. If swallowed, DO NOT induce vomiting. Seek medicalattention.

Aqua Mix® Penetrating Sealer

Published Date: 7/8/2013

TILING 09 30 00 Aqua Mix® / TDS­157

6 Availability & Cost

Location Item Code Size Package

USA 020372-4 1 qt (946 ml) BottleUSA 020373 1 gallon (3.78 L) BottleUSA 020374 5 gallon (19 L) PailUSA 020375* 55 gallon (210 L) DrumCanada C020372-4 1 qt (946 ml) BottleCanada C020373 1 gallon (3.78 L) BottleCanada C020374 5 gallon (19 L) Pail

* Indicates a special order item

7 Product Warranty

Custom® Building Products warrants to the original consumerpurchaser that its product shall be free from defects in material andworkmanship under normal and proper usage for a period of one yearfollowing the date of original purchase. Custom's® sole liability underthis warranty shall be limited to the replacement of the product. Somestates, countries or territories do not allow the exclusion or limitationof incidental or consequential damages, so the above limitation orexclusion may not apply to you. This warranty will not extend to anyproduct which has been modified in any way or which has not beenused in accordance with Custom's® printed instructions. Custom®makes no other warranties either expressed or implied. This warrantygives you specific legal rights, and you may have other rights that varyfrom state to state or from one country/territory to another. Click fordetails and complete warranty information.

8 Product Maintenance

Do not use cleaners containing ammonia, acids or bleach. Use anappropriate TileLab® or Aqua Mix® neutral cleaner. Tile industryexperts recommend periodic testing of sealed surfaces. Apply a fewdrops of water on the surface. If it soaks in, a coat of TileLab® orAqua Mix® sealer will be necessary to keep sealer at peakperformance.

9 Technical Services Information

For technical assistance, contact Custom® Building Products.

10 Filing System

Additional product information is available from the manufacturer uponrequest.

Expected Wear

EXPECTED WEAR UP TO 5 YEARS

Will vary depending on hardness and texture of surface, type of area,surface wear, frequency, and type of maintenance products usedWeather conditions, harsh cleaning methods, and high-alkaline, acidic,or solvent-based cleaners will affect wear

Handling & Storage

Close container tightly after each useStore in original container onlyStore and use between temperatures of 40° F ­ 90° F (4° C ­ 32° C)

Related Products

Aqua Mix® AquaShield™ Cleaner & Resealer

Aqua Mix® Penetrating Sealer

Published Date: 7/8/2013

TILING 09 30 00 Aqua Mix® / TDS­157

Coverage

Depends on type of stone or tile, porosity and texture of surface, temperature, humidity, and method of application.

Size Min Coverage Max Coverage

1 Gallon (3.78 L) 300 sq. ft. (28 M²) 1,000 sq. ft. (93 M²)

Aqua Mix® Penetrating Sealer

Published Date: 7/8/2013

F 7.3.12 - 0312 Data Sheets are subject to change without notice. For latest revision, check our website at www.laticrete.com. DS-6200.1-0712

1. PRODUCT NAME LATICRETE® Latasil™ 2. MANUFACTURER LATICRETE International, Inc. 1 LATICRETE Park North Bethany, CT 06524-3423 USA Telephone: +1.203.393.0010, ext. 235 Toll Free: 1.800.243.4788, ext. 235 Fax: +1.203.393.1684 Internet: www.laticrete.com 3. PRODUCT DESCRIPTION LATICRETE Latasil sealant is a high performance, one component, neutral cure, 100% silicone sealant designed for ceramic tile & stone applications. Uses Exterior and interior use. Swimming pools and other wet area applications. Joints for ceramic tile & stone applications. Expansion joints in residential and commercial applications. Advantages Conforms to the following properties under ASTM C–920:

Type S, Grade NS, Class 25, Use NT, Use I, Use M, Use G. Conforms to ASTM C-794 Adhesion Properties. Equipped with fungicides to resist mold & mildew growth. Resistant to pool chemicals. Matches top 19 LATICRETE grout colors and clear. Easy to smooth and tool.

Excellent for masonry construction. Excellent movement capacity—25% extension & compression. Can be used where ceramic tile abuts glass and window

framing. Compliments LATAPOXY® 310 Stone Adhesive system

(see section 10. FILING SYSTEMS). Suitable Substrates Stone Glass Metal/Steel Ceramic Tile Masonry Surfaces Wood and Plastic Surfaces Available Colors

6200 Clear 6217 Marble Beige

6222 Midnight Black 6223 Antique White

6224 Natural Grey 6230 Sand Beige

6235 Mocha 6239 Mushroom

6240 Latte 6242 Platinum

6244 Bright White 6250 Sea Glass

6252 Toasted Almond 6255 Tawny

6256 Desert Khaki 6257 Hot Cocoa

6258 Terra Cotta 6259 Espresso

6260 Dusty Grey 6261 Parchment

6266 Chestnut Brown 6267 Autumn Green

6278 Sterling Silver 6289 Smoke Grey

6285 Almond 6288 Silver Shadow

Packaging Available in 10.3 oz (305 ml) cartridges; 6 tubes per carton. Accessory Products LATICRETE Latasil 9118 Primer—one pint (.47 ℓ) jar, 5 pints (.47 l) per carton. Approximate Coverage Coverage will vary depending upon joint size and width.

Latasil™

DS-6200.1-0712

F 7.3.12 - 0312 Data Sheets are subject to change without notice. For latest revision, check our website at www.laticrete.com. DS-6200.1-0712

Approximately 11 lineal feet (3.35 m) per tube at 3/8" by 3/8" (9 mm x 9 mm) joint width.

Approximately 25 lineal feet (7.62 m) per tube at 1/4" by 1/4" (6 mm x 6 mm) joint width.

Shelf Life When stored in the original, unopened containers at or below 90°F (32°C), LATICRETE Latasil sealant has a 12 month shelf life. Limitations Adhesives/mastics, mortars and grouts for ceramic tile, pavers,

brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use a LATICRETE Waterproofing Membrane (see Section 10 FILING SYSTEMS).

A test area should be conducted when used with stone. Test sealant on small area to verify results.

Use LATICRETE Latasil 9118 Primer for porous stone and tile and for wet area applications. Conduct a test area to verify results.

Not for use in applications where physical abuse or abrasion is likely.

Do not use on or adjacent to building materials that may bleed oils, plasticizers or solvent materials such as impregnated wood, oil based caulks, green or partially vulcanized rubber gaskets or tapes.

For stone installations, test a small area to check for any fluid migration and to verify results.

Not a structural glazing adhesive. Joint depth should not exceed 1/2" (12 mm) thickness

(use backer rod for deeper joints). Joint width should not exceed 1" (25 mm) and be narrower

than 1/8" (3 mm). For perimeter sealing or expansion joint design, the ratio of the

joint width to sealant depth should be roughly 2:1. Cannot be painted. Cautions Consult MSDS for more safety information. Protect finished work from traffic and exposure to water until

fully cured, generally 24 hours at 70°F (21°C). Sealant must cure a minimum of 4 days at 70°F (21°C)/50%

R.H. prior to exposing to continuous water submersion. However, the other tile/stone installation materials (e.g.

mortars, membranes. grouts) must cure a minimum of 14 days at 70°F (21°C)/50% R.H. prior to exposing to continuous water submersion.

Maintain surface temperature between 40°F (4°C) and 90°F (32°C) during installation and for 24 hours thereafter.

Uncured sealant may irritate eyes if contact is made. Avoid contact with sealant until cured.

Keep out of reach of children. If uncured sealant comes in contact with skin, wash with soap

and water immediately. Always use LATICRETE® Latasil™ with adequate ventilation

and avoid prolonged breathing of vapor and prolonged skin contact.

4. TECHNICAL DATA Applicable Standard Adhesion performance according to ASTM C–794. Conforms to ASTM C–920 Sealant classification. Physical Properties

Service Temperature Range -40°F (40°C) to +350°F (177°C)

Sag or Slump None

Tack Free Time at 77°F (25°C), 50% RH 17 Minutes

Tooling Time 7–10 Minutes

Durometer Hardness–Shore A 27

Tensile Strength 280 psi (1.9 Mpa)

Dynamic Joint Movement +/-25%

Weatherability, 10,000 hours QUV Weatherometer

No Change

5. INSTALLATION Preparation Clean all joints and surfaces to receive sealant, removing all

foreign matter and contaminants such as grease, oil, dust, water, frost, surface dirt, old sealants and protective coatings.

Metal, glass and plastic surfaces should be cleaned by mechanical or solvent procedures. Simple detergent or soap and water treatments are not acceptable. In all cases where utilized, solvents should be wiped on and off with clean, oil and lint free cloths.

When using any solvent always follow solvent manufacturer’s safety, handling and installation recommendations.

Application Substrates For Priming Use LATICRETE Latasil 9118 Primer for these substrates: Stainless Steel Sandstone * Metal Limestone (or other Porous Stones) PVC Fiber Reinforced Cement * Subject to testing and approval by LATICRETE. Actual stone samples to be provided for testing.

Swimming Pool Application: Use LATICRETE Latasil 9118 Primer for all permanent wet area applications. For underwater or continuous wet area applications,

polyethylene foam backer rod is recommended. Use polyethylene bond breaker tape on joints too shallow to accommodate foam rod. Polyethylene backer rod is “closed cell” which is water repellent.

General Installation Instructions:

F 7.3.12 - 0312 Data Sheets are subject to change without notice. For latest revision, check our website at www.laticrete.com. DS-6200.1-0712

Use polyurethane or polyethylene foam backer rod for deep joints. Use polyethylene bond breaker tape on joints too shallow to accommodate foam rod. These materials allow the silicone to stretch freely with joint movement.

Apply masking tape to the face of the veneer. Masking tape will allow for easier removal of sealant if it comes into contact with the face of the veneer. Sealant should only be applied into the joints, adhering to the flanks of the veneer. Applying the masking tape results in a cleaner look, and allows for easy tooling without affecting the face of the veneer.

Apply sealant into the joint, filling completely. Finish joints with a “Jointing Tool” when complete (within 5–7

minutes) for a smooth professional finish. Proper tooling of the sealant ensures contact with the joint flanks.

Remove masking tape immediately after tooling. Wipe any sealant off the face of the veneer immediately.

Cleaning Cured joints should be cleaned regularly with a neutral pH cleaner. 6. AVAILABILITY AND COST Availability LATICRETE and LATAPOXY® materials are available worldwide. For Distributor Information, Call: Toll Free: 1.800.243.4788 Telephone: +1.203.393.0010 For on-line Distributor information, visit LATICRETE at www.laticrete.com. Cost Contact a LATICRETE Distributor in your area. 7. WARRANTY See 10. FILING SYSTEM DS 230.13: LATICRETE Product Warranty A component of: DS 230.05: LATICRETE 5 Year System Warranty DS 230.15-APD: LATICRETE 15 Year System Warranty – APD

For Steel or Wood Framed Exterior Facades DS 230.15-SPD: LATICRETE 15 Year System Warranty – SPD

For Steel or Wood Framed Exterior Facades DS 025.0-APD: LATICRETE 25 Year System Warranty – APD DS 025.0-SPD: LATICRETE 25 Year System Warranty – SPD DS 230.99: LATICRETE Lifetime System Warranty 8. MAINTENANCE Joints should be cleaned regularly with neutral pH cleaners. 9. TECHNICAL SERVICES Technical Assistance Information is available by calling the LATICRETE Technical Service Hotline (hours 8:00 AM to 5:30 PM EST): Toll Free: 1.800.243.4788, ext. 235 Telephone: +1.203.393.0010, ext. 235 Fax: +1.203.393.1948

Technical and Safety Literature To acquire technical and safety literature, please visit our website at www.laticrete.com. 10. FILING SYSTEM Additional product information is available on our website at www.laticrete.com. The following is a list of related documents: DS 230.13: LATICRETE® Product Warranty DS 230.05: LATICRETE 5 Year System Warranty DS 230.15-APD: LATICRETE 15 Year System Warranty – APD

For Steel or Wood Framed Exterior Facades DS 230.15-SPD: LATICRETE 15 Year System Warranty – SPD

For Steel or Wood Framed Exterior Facades DS 025.0-APD: LATICRETE 25 Year System Warranty – APD DS 025.0-SPD: LATICRETE 25 Year System Warranty – SPD DS 230.99: LATICRETE Lifetime System Warranty DS 236.0: LATICRETE 9235 Waterproofing Membrane DS 661.0 Air & Water Barrier DS 663.0.: LATICRETE Hydro Ban DS 679.0: LATAPOXY® 310 Stone Adhesive DS 6528.1: LATICRETE Latasil 9118 Primer

SOLIDS

ARCTIC WHITE (2) D617

PEPPER WHITE (1) D037

BISCUIT (1)D317

GOLDEN GRANITE (2)D138

ALMOND (2)D335

MARBLE (2)D325

URBAN PUTTY (1) D161

URBAN PUTTY SPECKLE (1) D201

MINT ICE (2)D152

GARDEN SPOT (2) D141

CYPRESS (2) D452

OAK MOSS (3)D195

SPA (1)D148

AEGEAN (3) D192

ARCHITECTURALGRAY (2) D109

BUFFSTONE RANGE (1) D147

ELEMENTAL TAN (1) D166

ELEMENTAL TAN SPECKLE (1) D175

MOTTLED MEDIUM BROWN (1) D050

UPTOWN TAUPE (2) D132

UPTOWN TAUPE SPECKLE (2) D202

ARTISAN BROWN (2) D144

ARTISAN BROWN SPECKLE (2) D204

CITYLINE KOHL (3) D171

CITYLINE KOHLSPECKLE (3)D207

CRISP LINEN (1) D139

CORNSILK (2)D160

LUMINARY GOLD (2) D142

MUSTARD (4) D181

PUMPKIN SPICE (4) D090

SEA SPEC (3) D372

WATERFALL (1) D169

GALAXY (4) D023

NAVY (4) D189

NAVY SPECKLE (4) D209

DESERT GRAY (1) D014

CLEMENTINE (S) D622

DESERT GRAY SPECKLE (1) D200

SUEDE GRAY (2) D182

SUEDE GRAY SPECKLE (2) D208

BLACK (3) D311

CASTLEROCK (3) D618

DEEP PURPLE (4) D044

BEACH DK04 KHAKI DK12

CHOCOLATE DK13 MOONLIGHT DK14

WINDMILL DK20 MIRAGE DK11

CINNAMON RANGE (3) D007

RED (S) D017

LIME SHERBET (4) D619

SUNSHINE (4) D620

NAUTICAL BLUE (4) D621

AQUA GLOW (3) D197

OCEAN BLUE (4) D159

COLORBODY™ PORCELAINKEYSTONES™

BLENDS

*2 x 1 brick-work mosaics are available in all blend colors. Mosaic Blend components available at www.daltile.com/keystones.

MOONLIGHT DK14 2 x 1 Brick-work Mosaic*

Made-to-order Available in 1" Hexagon Available in 2" Hexagon made-to-order

Available in 2 x 1 & 2 x 4 sizes Red D017 and Clementine D622 are made-to-order only;

trim not available.

Colors arranged by price groups, Group (1) being the least expensive.All Keystones™ 1 x 1 and 2 x 2 mosaics are offered in all colors and available on a standard made-to-order basis using ClearFace™ mounting system.

COMMERCIAL USAGEINTERIOR EXTERIOR

ResidentialLight

Commercial Commercial Residential Commercial

Floors/Patios

Walls/Backsplashes

Countertops

Pool Decking

Pool Linings

Pool Tank/Submerged Applications**

Suitable for exterior patios (including pool decks and linings) in freezing and non-freezing climates when proper installation methods are followed.

For pool installations, Keystones is available in ClearFace™ mount film. Contact your sales representative for more information.

**Keystone ClearFace™ mounted mosaics recommended for pool tanks and submerged applications.

RESIDENTIAL USAGE

FLOORS WALLS COUNTERTOPSEXTERIOR

PATIOSEXTERIOR

POOL DECKS

F W C EP ED

SIZESSQ.FT.

CARTONPIECES PER CARTON

2 x 2 Mosaic Tile(Dot-mounted on 1' x 2' sheet)

(Piece 1-15/16" x 1-15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

24.00 12

1 x 1 Mosaic Tile(Dot-mounted on 1' x 2' sheet)

(Piece 15/16" x 15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

24.00 12

2 x 1 Straight-joint Mosaic(Dot-mounted on 1' x 2' sheet)

(Piece 1-15/16" x 15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

24.00 12

2 x 1 Brick-work Mosaic(Dot-mounted on 1' x 2' sheet)

(Piece 1-15/16" x 15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

22.00 12

2" Hexagon Mosaic(Dot-mounted on 1' x 2' sheet)

(Piece 1-15/16" x 1-15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

24.24 12

1" Hexagon Mosaic(Dot-mounted on 1' x 2' sheet)

(Piece 15/16" x 15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

21.00 12

2 x 4 Straight-joint Mosaic(Dot-mounted on 1' x 2' sheet)

(Piece 1-15/16" x 3-15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

24.00 12

2 x 4 Brick-work Mosaic(Dot-mounted on 1' x 2' sheet)

(Piece 1-15/16" x 3-15/16")(Sheet 11-7/8 x 23-7/8)(Sheet 30.23 cm x 60.71cm)

20.04 12

TRIMTYPE NUMBER SIZE PIECES PER

CARTON GROUPS

Bullnose S-862 1 x 1 196 1, 2

Bullnose S-886 2 x 2 108 1, 2, 3, 4

Bullnose S-4249 2 x 4 180 1, 2

Bullnose Corner SC-862 1 x 1 100 1, 2

Bullnose Corner SC-886 2 x 2 100 1, 2, 3, 4

Cove Base C-813 1 x 1 84 1, 2

Cove Base C-833 2 x 2 84 1, 2, 3

Cove Base Corner CB-813 1 x 1 100 1, 2

Cove Base Corner CK-813 1 x 1 100 1, 2, 3

Cove Base Corner SB-816 2 x 2 100 1, 2

Cove Base Corner SC-816 2 x 2 100 1, 2

Outcorner SCRL-833 2 x 1 100 1, 2, 3

Universal Trim S-812 1 x 1 112 1, 2

Universal Trim S-832 2 x 2 112 1, 2

Universal Trim SC-813/SU-813 2 x 2 100 1, 2, 3

Universal Trim C-701 1 x 1 50 1, 2, 3, 4

Build-up Base MB-4C (3) Rows 1 x 1(1) Row C-813 26 1, 2

Build-up Base MB-5(1) Row S-862(3) Rows 1 x 1(1) Row C-813

26 1, 2

Build-up Base MB-5A (2) Rows 2 x 2(1) Row C-833 26 1, 2, 3

Build-up Base MB-5B(1) Row S-886(1) Row 2 x 2(1) Row C-833

26 1, 2, 3

Made-to-order

SHADE VARIATION

to

LOW (V1) – SOLIDSMonochromatic; consistent color within each tile and from tile to tile.

HIGH (V3) – MOTTLED or SPECKLEDColor variation from tile to tile and within each tile.

RANDOM (V4) – BLENDSColor variation from tile to tile and within each tile.

INSTALLATION

THICKNESS GROUT JOINT RECOMMENDATION

1/4" 1/8" Approximately

NOTESAll colors in 1 x 1 and 2 x 2 are available with ClearFace™ mounting system on a made to order basis.

7834 C. F. Hawn Freeway | Dallas, TX 75217 | 214.398.1411 800.933.TILE For more information about Daltile products and services, visit our website at DALTILE.COM.

© 2015 Dal-Tile Corporation (2/15)

TEST RESULTSASTM# Result

Water Absorption C373 < 0.5%

Breaking Strength C648 300 lbsScratch Hardness MOHS N/AChemical Resistance C650 Resistant

Dynamic C.O.F. A137.1 (Non-abrasive) Wet: ≥ 0.42 (Abrasive) Wet: ≥ 0.60

A DCOF value of ≥ 0.42 is the new standard for tiles specified for commercial application in standard A137.1–2012, Section 9.6. It replaces the SCOF value of ≥ 0.60 referenced in ASTM C1028. For more information on the correlation between the two values and about the DCOF AcuTest,™ please visit http://daltile.com/information/DCOF.

COLORBODY™ PORCELAINKEYSTONES™

ALMOND 0135 (1)

CRISP LINEN 0139 (1)

CORAL BEAD Q092 (4)

OAK MOSS 0195 (3)

VERMILLION 0DM1 (5)

ARCTIC WHITE 0190 (1)

ALMOND K165 (2)

MOON BEAM Q091 (4)

ORANGE BURST Q097 (4)

SPA 0148 (1)

ICE GREY K176 (2)

NAVY K189 (3)

AQUA GLOW 0197 (3)

WHITE 0100 (1)

URBAN PUTTY 0161 (1)

CORNSILK 0160 (1)

FIRE BRICK Q093 (4)

AEGEAN Q192 (4)

DESERT GRAY X114 (1)

WHITE K101 (2)

ARCHITECTURAL GRAY 0109 (2)

LUMINARY GOLD 0142 (2)

KEY LIME Q098 (4)

SUEDE GRAY 0182 (2)

GOLDEN GRANITE 0138 (1)

UPTOWN TAUPE 0132 (2)

GOLD COAST 0191 (3)

OCEAN BLUE Q049 (4)

BLACK K111 (2)

PEPPER WHITE 0147 (1)

ELEMENTAL TAN 0166 (1)

SUNFLOWER DH50 (3)

MISTY MEADOW 0112 (2)

GARDEN SPOT 0141 (2)

WATERFALL 0169 (1)

WOOD VIOLET Q467 (4)

ARTISAN BROWN 0144 (2)

MUSTARD Q012 (4)

MINT ICE 0152 (2)

CARNATION PINK Q095 (4)

COBALT DM14 (3)

BISCUIT K175 (2)

CITYLINE KOHL 0171 (3)

PUMPKIN SPICE Q090 (4)

CYPRESS 1452 (1)

GALAXY 1469 (1)

CHIANTI Q094 (4)

floor

• w

all •

cou

nter

top Field Tile

Glazed Wall & CounterSemi-GloSS™

(1), (2), (3), (4) and (5) indicate Price Groups, (1) being the least expensive."Q" colors are Special Order. Subject to crazing; black grout not recommended. Made-to-order colors.See the Rittenhouse Square Collection for colors available in 3 x 6 sizes.See the Modern Dimensions Collection for colors available in 4-1/4 x 8-1/2 and 4-1/4 x 12-3/4 sizes.

SIZES

SQ.FT. CARTON

PIECES PER CARTON

6 x 6 Field Tile (6" x 6") (15.2 cm x 15.2 cm) 12.50 50

4-1/4 x 4-1/4 Field Tile (4-1/4" x 4-1/4") (10.8 cm x 10.8 cm) 12.50 100

RESIDENTIAL USAGE

FLOORS WALLS COUNTERTOPS EXTERIOR PATIOS

EXTERIOR POOL DECKS

F* W** C*** eP ed * Matte finish suitable for residential bathroom floors only, not subject to outside foot traffic. ** Suitable for exterior walls in non-freezing climates only.*** Darker colors may show scratches.

SHADE VARIATION

LOW (V1)Monochromatic; consistent color within each tile and from tile to tile.

INSTALLATION

THICKNESS GROUT JOINT RECOMMENDATION

5/16" 1/16"TEST RESULTS

ASTM# WALL RESULT

Water Absorption C373 < 20.0%

Breaking Strength C648 120-230 lbs

Scratch Hardness MOHS 4.0-6.5

Chemical Resistance C650 Resistant

Coefficient of Friction* C1028 Wet: < 0.50 Dry: ≥ 0.80

*Matte finish only

SLIP RESISTANCE (WET) : 1 & 2The higher the rating, the higher the slip resistance.

1 < .50 (SEMI-GLOSS)

2 .50 - .59 (MATTE)

3 ≥ .60

COMMERCIAL USAGE

INTERIOR EXTERIOR

RESIDENTIALLIGHT

COMMERCIAL COMMERCIAL RESIDENTIAL COMMERCIAL

Floors/Patios Bathrooms Only**

Walls/Backsplashes

Countertops*

Pool Decking

Pool Linings

Suitable for non-freezing climates when proper installation methods are followed.

* Darker colors on countertops may show scratches** Matte finish only

NOTES

Since there are variations in all fired ceramic products, tile and trim supplied for your particular installation may not match these samples. Final color selection should be made from actual tiles and trim and not from tile and trim samples or color reproductions. Manufactured in accordance with ANSI A 1371.1 standards.

Water, oil, grease, etc. create slippery conditions. Floor applications with exposure to these conditions require extra caution in product selection. Not for use on ramps.

For additional information refer to “Factors to Consider” at: www.daltile.com/CommercialFactors or www.daltile.com/ResidentialFactors.

TRIM

TYPE NUMBER SIZE SEMI-GLOSS MATTE

Bullnose* A-4200 2 x 6 Group 1 Group 1

Bullnose Corner* AN-4200 2 x 2

Bullnose** S-4269 2 x 6

Bullnose** S-4449 4-1/4 x 4-1/4

Bullnose** S-4669 6 x 6 Groups 1, 2, 4 Groups 1, 2

Bullnose Corner** SN-4269 2 x 2

Bullnose Corner** SCR-L-4449 4-1/4 x 4-1/4

Bullnose Corner** SCR-L-4669 6 x 6 Groups 1, 2, 4 Groups 1, 2

Cove* A-3401 4-1/4 x 4-1/4 Groups 1, 2, 4 Groups 1, 2

Cove* A-3601 6 x 6 Groups 1, 2, 4 Groups 1, 2

Cove* A-3461 4-1/4 x 6 Group 1 Group 1

Cove Corner* SCR-L-3401 4-1/4 x 4-1/4 Groups 1, 2, 4 Groups 1, 2

Cove Radius Corner* ACR-L-3401 4-1/4 x 4-1/4 Groups 1, 4 Group 1

Cove Corner* SCR-L-3601 6 x 6 Groups 1, 2, 4 Groups 1, 2

Sanitary Cove Bases S-3419T 4-1/4 x 6 Groups 1, 2, 4 Groups 1, 2

Sanitary Cove Bases S-3619T 6 x 6 Groups 1, 4 Group 1

Sanitary Cove Base Corners SCRL-3419T 4-1/4 x 6 Groups 1, 2, 4 Groups 1, 2

Sanitary Cove Base Corners SCRL-3619T 6 x 6 Groups 1, 4 Group 1

Quarter Round A-106 3/4 x 6 Groups 1, 2, 4 Groups 1, 2

Quarter Round Beak AC-106 3/4 x 6 Groups 1, 2, 4 Group 1, 2

Sink Rail/V-Cap* WA-8262 2-1/2 x 2 x 6 Groups 1, 2† Group 1

Sink Rail/Outside Corner* WAC-8262 2-1/2 x 2 Groups 1, 2† Group 1

All colors available (except 0DM1) through Special Order.

* For conventional mortar installation ** For thinset bed installations Roundtop Made-to-order

† Only available in colors K101, K111, K165 and K175.

Available in all groups.