review of mc type c to c assembly clearances with c2 to c5 shell surface interface details
DESCRIPTION
Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details. 12/19/06. Rev 4. 1. 10. C2. 20. 30. C5. Sec - C. Sec – D looking outside. 50. 40. C2. 30. C5. Sec - B. Sec - A. Sec – D looking inside. Clamp interference. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/1.jpg)
C2 to C5 fit up review-R4 1
Review of MC Type C to C assembly clearances
with
C2 to C5 shell surface interface details
12/19/06
Rev 4
![Page 2: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/2.jpg)
2
Sec - C
C2
C5
1
10
2030
![Page 3: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/3.jpg)
3
Sec – D looking outside
![Page 4: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/4.jpg)
4
Sec - B
C2
C5
30
40
50
![Page 5: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/5.jpg)
5
Sec - A
![Page 6: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/6.jpg)
6
Sec – D looking inside
![Page 7: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/7.jpg)
7
Clamp interference
![Page 8: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/8.jpg)
8
No local interferences with CAD defined services
![Page 9: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/9.jpg)
9
Clamp interference
![Page 10: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/10.jpg)
10
0.323 min CAD clearance
![Page 11: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/11.jpg)
11
0.25 offset of inner surface of poloidal break leaves 0.073” clearance
![Page 12: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/12.jpg)
12
0.25 offset of inner surface of poloidal break leaves 0.073” clearance
Based on final C2 measurements, MC C2 poloidal break extends inward 0.19” along the full surface. See slide 24.
![Page 13: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/13.jpg)
13
Type C2
0.323” min clearance to Interfacing Type C
![Page 14: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/14.jpg)
14
0.624” min clearance to Interfacing Type C
![Page 15: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/15.jpg)
15
MTM metrology data points shown as white points.
Steve’s original metrology data points are red points
Interfacing Type-C wings is shown in overlay with underside surface represented.
![Page 16: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/16.jpg)
16
There are minimum points to inspect but Se141-116-wing-c clearance looks okay with a 0.222” clearance identified at one location. The underside surface of the wing is typical out by +0.025”, leaving a minimum clearance of 0.197”.
0.253
0.294
0.267
0.33
0.247
0.363
0.222
0.575
0.264 0.280.67
Slide taken from review: C2 MTM metrology review-R1
Type C2
Interfacing Type C
wing
0.481
0.448
0.634
0.566
![Page 17: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/17.jpg)
17
Type C2
Interfacing Type C
wing0.221” min clearance
![Page 18: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/18.jpg)
18
Mark up for 1/6” -1/8” grind area
Slide taken from review: C2 MTM metrology review-R1
Additional grinding on Type C2 was done in region shown.
![Page 19: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/19.jpg)
19
The surface offset of pints in the pink area is in the range of +.021” to +.039” except where noted.
The surface offset of pints in the blue area is in the range of +.075” to .102”. Nominal surface cut is .12” Are we deep enough?
Offset of pints in the orange area is in the range of .020” to .037”.
The values shown is the machined surface of the large Wing C male side. It will interface with the surface shown in slide 6.
C to C Side
Outside Large Wing E Side
+.032
+.037
+.041
+.048
+.054
+.052+.067
+.055+.050
+.070
+.054
+.042
+.043
+.038
+.038
+.036
+.039
Slide taken from review: MC C5 review-R1
![Page 20: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/20.jpg)
20
The following slides are full wing and flange scans of C2 and C5
Mike Ducdo data: 120606_c2_wing_scan.IGS. Points shown are centers of 1.5” Ø measurement probe.
![Page 21: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/21.jpg)
21
The as-built surface is generally off by +0.030” with a few front edge point out be +0.050”
120606_c2_wing_scan DATA
![Page 22: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/22.jpg)
22
0.058” MTM 0.061” Duco
0.19” MTM 0.20” Duco 1.18” to C5
0.065” MTM 0.070” Duco
0.03” to 0.04”
0.23” min C to C CAD space
0.03” to 0.05”
General 0.35” C to C CAD space in this area
120606_c2_wing_scan DATA
![Page 23: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/23.jpg)
23
0.23” min C to C CAD space. surface measured data is in the range of 0.0” to +0.01”
120606_c2_wing_scan DATA
![Page 24: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/24.jpg)
24
+0.10” OOT at the root (point indicated)
+0.02” to -.08” surface variation over the remainder of the cut region.
+0.06” Out of Tolerance in the enclosed area.
MC C2 metrology data shown
![Page 25: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/25.jpg)
25
MC C2 poloidal break extends inward 0.19” along the full surface.
MC C2 metrology data shown
![Page 26: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/26.jpg)
26
Based on final measurements of C2 and C5 a gap of +0.033 exists at the poloidal break interface area. Local grinding on this wing is needed to increase the gap.
The C5 small wing geometry is similar to C2 (see slide 30).
![Page 27: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/27.jpg)
27
The as-built surface is generally off in the range of +0.030” to +0.050”
121106_c5_wing_scan DATA
![Page 28: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/28.jpg)
28
0.170” Duco 0.87” to C2
0.20” Duco 1.18” to C2
0.050” Duco 0.42” to C2
0.02” to 0.06”
0.23” min C to C CAD space
0.05”
General 0.35” C to C CAD space in this area
121106_c5_wing_scan DATA
![Page 29: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/29.jpg)
29
0.23” min C to C CAD space. surface measured data is in the range of -0.05”
121106_c5_wing_scan DATA
![Page 30: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/30.jpg)
30
+0.16” OOT at the root (point indicated)
+0.05” to -.02” surface variation over the remainder of the cut region.
+0.06” Out of Tolerance in the enclosed area.
MC C5 metrology data shown
![Page 31: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/31.jpg)
31
MC C5 poloidal break extends inward 0.18” along the full surface.
MC C5 metrology data shown
I though C5 break inner surface was nearly flush… check this.
![Page 32: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/32.jpg)
32
MC C5 metrology data MC C2 metrology data
Surface measures -0.07” to -0.13”
Surface measures -0.13” to -0.17”
Surface -0.02” to +0.14”
Surface -0.05” to +0.15”
![Page 33: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/33.jpg)
33
Measured CAD distance with C2 and C5 located in their translated positions.
Origin (inches) Orientation (degrees) X Y Z About X About Y About ZC1r1 0.00040934 0.00674867 0.00309482 0.00402910 -0.00164692 -0.00234224C2r1 -0.00323208 -0.03096037 0.02236041 0.02613692 0.05253439 0.01904024C3r1 -0.01426276 -0.01285752 -0.02457020 0.03075978 0.03998892 -0.01316786C4r1 0.01163284 0.00620140 0.01452996 -0.03328320 -0.00150808 0.00988164
The movement of C2 and C5 was made using Art’s large motion case (r1) provided in email (FW C1-4 Realignment Coordinate Transformations in ProE nomenclature) dated 10/6/06. C2 was positioned using C2r1 data and C5 positioned using C4r1 data. The translated position is based on the CS0 coordinate system.
![Page 34: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/34.jpg)
34
0.1997” CAD gap
C2
C5
![Page 35: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/35.jpg)
35
0.311” CAD gap
Large wing underside local
surface
C2
C5
![Page 36: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/36.jpg)
36
0.336” CAD gap
Large wing local front nose
surfaceC2
C5
![Page 37: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/37.jpg)
37
0.461” min bladder inner surface CAD gap
Inside surface of bladder pocket
C2
C5
![Page 38: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/38.jpg)
38
0.212” CAD gap
C2
C5
![Page 39: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/39.jpg)
39
0.375” CAD gap
C2
C5
![Page 40: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/40.jpg)
40
0.371” CAD gap
Large wing local front nose surface
C2
C5
![Page 41: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/41.jpg)
41
0.4297” CAD gap
C2
C5
0.443” CAD gap
0.560” CAD gap
0.567” CAD gap
(inside corners)
Side-B
Side-A
Side-A
![Page 42: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/42.jpg)
42
0.311” CAD clearance to underside surface of poloidal break.
Expected gap = .311 -.20 - .06 = +.051”
C2
C5
0.58” at root
+.06” AB
+.2” AB break lower surface
4.35”
![Page 43: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/43.jpg)
43
C2
C5
4.2”
0.387” CAD clearance to underside surface of poloidal break.
Expected gap = .387 -.20 - .06 = +.127”
0.62” at root
![Page 44: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/44.jpg)
44
Post grinding C5
Plane located 4.35” from flange face.
-0.042” red
+0.039” blue
+0.043” blue
-0.047” red
-0.025” red
-0.00” red
![Page 45: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/45.jpg)
45
●
●
●
1. 8 monuments are located on each mating MC, so positioned that they can be seen by the Lica metrology system which has been optimally positioned. The monuments are to be located on stable surfaces where part deflection is minimal.
2. The first MC is positioned on the Stage 2 support stand and secured in place.
3. A reference coordinate system (to be designated ACS0) will be determined through metrology measurement of the first MC, referencing the 8 monuments.
![Page 46: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/46.jpg)
46
![Page 47: Review of MC Type C to C assembly clearances with C2 to C5 shell surface interface details](https://reader035.vdocument.in/reader035/viewer/2022062500/56814ef8550346895dbc8907/html5/thumbnails/47.jpg)
47
C2 pt 1
C2 pt 2
C2 pt 3C5 corner
pts