rf test menuw01-0670.web.dircon.net/support/manuals/ajhd3700he...– 140 – rf test menu this menu...
TRANSCRIPT
– 140 –
RF TEST menu
This menu is displayed by pressing the following keys: > F2TEST
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 141 –
RF TEST menu
Key
F1
F2
F3
F4
F5
F6
F7
F8
F9–F10
F11
F12
F13
Key designation
EECC SMPLChange of error ratemeasurement time.
METERSwitch of meter display.
——
LOADLoad of default value.
——
MODE
CH
EXIT
——
ADJ RFRF adjustment valuedisplay.
——
HEAD CLNManual head cleaning.
Description
FAST: Measurement interval is 20 fields.SLOW: Measurement interval is 2 seconds.
ERROR: Displays inner error level.ENV: Displays envelop level.
All RF adjustment values return to factory settings.(Executes when pressed together with F key.)
For selecting waveform monitor (WFM) output.°EYE: Outputs eye pattern.ENV: Outputs envelop.CONFI: Outputs CONFI CTL.R/P: Outputs R/P CTL.TC: Outputs TC waveform.
For selecting EYE/ENV channel.°CH0: Selects EYE or ENV of CH0.CH1: Selects EYE or ENV of CH1.CH2: Selects EYE or ENV of CH2.CH3: Selects EYE or ENV of CH3
Returns the VTR to the TEST menu screen.
RF adjustment value is displayed and F6, F7, F11 and F12functions change to RF adjustment value display mode.Refer to “RF adjustment value display menu” (page 143).
While this key is pressed, head cleaning takes place.(Head cleaning lasts for a maximum of only 20 seconds.)Operation1. Set VTR to PLAY mode.2. Press the F13 (HEAD CLN) key.Head cleaning functions during PLAY, JOG or VAR mode.
°When the RF adjustment value display mode has been entered by F11, the WFM selection made immediatelybeforehand is held.
– 142 –
RF TEST menu
∑ Error rate display
The error rates (error occurrence rates) are indicated on the 1) TOTAL ERROR and 2) INNER ERROR displays.
1) TOTAL ERRORDuring recording, the error rate of the simultaneous playbacksignals is displayed. During playback, the error rate of the play-back signals is displayed. The audio channels are switchedusing the center cursor key.
2) INNER ERRORThe error rates after the inner errors have been corrected aredisplayed for the 8 heads.
Proceed as follows to switch between VIDEO & AUDIO andAUDIO.
1. Press the center cursor key to display the cursor.
2. Press the F key and cursor key (2 or 1) together to movethe cursor to INNER ERROR.
3. Press the center cursor key to select VIDEO & AUDIO orAUDIO.
4. Press the ENT key to enter the selection.
∑ Correction and revision statuses
≥Press the F key and cursor key together to move the highlighted portion from the error rate display described above.
≥By aligning the cursor with CONCEAL V or A, with OUTER V or A, or with INNER and then pressing the center cursor key, it is possible to switch between ON and OFF.
≥These settings are forcibly set to ON when the test menu is exited. Do NOT turn them OFF since doing sowill cause noise to be generated in the playback picture and sound.
TOTAL ERROR
VIDEO AAUDIOOUTER CH1
INNER ERRORVIDEO & AUDIO
54321
54321
54321
B A B A B ACH0 CH1 CH2 CH3
B
– 143 –
RF adjustment value display menu
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
Key
F1–F5
F6
F7
F8–F10
F11
F12
Key designation
——
ADJ MODEAdjust mode.
ADJ CH
——
ADJ RFRF adjustment valuedisplay.
ADJ SEL
Description
FIX: Holds the current adjusted value. Parameter can bereadjusted by remote adjustment but the value cannot bechanged with this unit.
Selects the channel for display.EQ/REC/PLL: CH0, CH1, CH2, CH3
When the F11 key is pressed, ADJ SEL is displayed at the F12key and the current adjusted value of the selected parameter isdisplayed. Selects adjustment mode with F6 key and channelwith F7 key.
This is used to display the selected RF adjusted value.EQ: The adjusted value of the playback equalizer is displayed.REC: The recording adjusted value is displayed.PLL: The PLL relative speed adjusted value is displayed.Pressing the F12 key enables switching by a toggling action inthe following sequence: ¢¢¢¢EQ>¢¢¢¢PLL>¢¢¢¢REC>¢¢¢¢EQ>and so on.Pressing the F key and F12 key together enables switching by atoggling action in the following sequence: 6014¢¢>6018¢¢>501¢¢>24P¢¢>D3¢¢>6014¢¢ and so on.The RF system adjusted values for each format are displayed asthese adjusted values. (They are used by the servicingengineer.)
– 144 –
AUDIO TEST menu
This menu is displayed by pressing the following keys: > F3TEST
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
Key
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Key designation
CH-1
CH-2
CH-3
CH-4
CUE
MONI.L
MONI.R
EXIT
REF.LEV
IMPED.
——
OUT LEV.
IN LEV.
Description
Sets the CH1 analog input/output reference level.
Sets the CH2 analog input/output reference level.
Sets the CH3 analog input/output reference level.
Sets the CH4 analog input/output reference level.
Sets the CUE input/output reference level.
Sets the monitor L channel output reference level.
Sets the monitor R channel output reference level.
Returns the VTR to the TEST menu screen.
Sets the PCM audio reference level. (This can be done only inthe servicing engineer mode.≥When the F9 and F keys are pressed together, the reference
level (Fs) toggles between j18 dB and j20 dB.
Sets the input impedance. (This can be done only in theservicing engineer mode°.)≥When the F10 and F keys are pressed together, the input
impedance is toggled between 600 ohms and HIGH.
Sets the analog output reference level.≥When the F12, BS and F keys are pressed together, the names
of the F1 to F7 menus are displayed, and switching betweenthem is acknowledged.
Sets the analog input reference level.≥When the F12, BS and F keys are pressed together, the names
of the F1 to F5 menus are displayed, and switching betweenthem is acknowledged.
– 145 –
MECHA TEST menu
This menu is displayed by pressing the following keys: > F4TEST
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
The menu below is displayed when the key is pressed.F5
– 146 –
Key
F1
F2
F3
F4
F5
F6–F7
F8
F9–F13
Key designation
MODELoading without tape.
——
C.SIZECassette size selection.
——
SENSORSensor operation check.
——
EXIT
——
Description
NORMAL: Normal operation.NO-TAPE: Loading without cassette tape is possible. Loading
starts when the STOP button is pressed. Cassette isselected with F3 key. To abort operation, press theEJECT button.
Selects the size of the pseudo cassette when [NO TAPE] hasbeen selected with F1 key. Large, medium or small cassette sizecan be selected.
When this key is pressed for highlighting, the sensor frame isshown on the menu. Operation of each peripheral sensor ofcylinder, reel base and front loading is checked. This key isespecially for checks by service personnel.Press the F8 (EXIT) key to restore the original frame.
Returns the VTR to the TEST menu screen.
MECHA TEST men
– 147 –
SYSTEM TEST menu
This menu is displayed by pressing the following keys: # .This menu contains keys for adjustments by service personnel. General users cannot operate these keys.Press F8 key to return to TEST menu.
F5TEST
Key
F1–F7
F8
F9–F13
Key designation
——
EXIT
——
Description
Returns the VTR to the TEST menu screen.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 148 –
SERVO TEST menu
This menu is displayed by pressing the following keys: # .F7TEST
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 149 –
SERVO TEST menu
Key
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Key designation
TORQUEReel torque adjustment.
DATA SENDTorque data forwarding.
MEASURE(Measure)
ATAT head adjustment.
METER
PG SHIFTPG shifter adjustment.
ADJ RATEAdjust rate.
EXIT
MECHAMechanical adjustment.
TRACKINGTracking adjustment.
——
BIMORPH INITRemoval of hysteresis atAT voltage element.
ADJ ENABLE
Description
Key for adjustment by service personnel.
Key for adjustment by service personnel.
Key for adjustment by service personnel.
Key for adjustment by service personnel.
ERROR: Displays inner error level.ENV: Displays envelop level.
Key for adjustment by service personnel.
Key for adjustment by service personnel.
Returns the VTR to the TEST menu screen.
Key for adjustment by service personnel.
Under normal conditions, tracking adjustment is not necessary.Adjust if there are tracking discrepancies while editing.VAR: Tracking is adjusted manually. Refer to “Manually
adjusting the tracking” (page 96).FIX: Tracking is fixed at the center position of the
manual adjustment.OPT. ONCE: Tracking is optimized only once while the tape is
playing up to the IN point during the first editingafter the cassette has been inserted. Thereafter,optimization does not take place. However,optimization can be performed again. Refer to“Automatically adjusting the tracking” (page 95).
OPT. AUTO: Tracking is optimized while the tape is playing upto the IN point with each editing. Refer to“Automatically adjusting the tracking” (page 95).
Key for adjustment by service personnel.
Key for adjustment by service personnel.
– 150 –
SERVO TEST menu
∑ Error rate display
The error rates are displayed in terms of the 1) TOTAL ERRORand 2) INNER ERROR.For details, refer to the description of the error rate display for theRF TEST menu (on page 142).
∑ Tracking adjustment
For details of the tracking adjustment, refer to the INSERT/ASSEMBLE MANUAL EDIT SET UP menu (onpage 95).
– 151 –
TEST FRONT menu
This menu is displayed by pressing the following keys: # F6TEST
Key
F1
F2
F3–F7
F8
F9–F13
Key designation
PANELDisplay check.
KEYCHECKFront panel key check.
——
EXIT
——
Description
Transfers the VTR to TEST FRONT PANEL menu screen.
Transfers the VTR to the TEST KEY CHECK menu screen.
Returns the VTR to the TEST menu screen.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 152 –
Key
F1
F2–F7
F8
F9–F13
Key designation
MODEDisplay dot check.
——
EXIT
——
Description
The entire display panel is lighted up in a fixed pattern anddisplay dots are checked. Each time the key is pressed, 12 typesof pattern are displayed.
Returns the VTR to the TEST FRONT menu screen.
TEST FRONT PANEL menu
This menu is displayed by pressing the following keys: # # .F1F6TEST
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 153 –
TEST FRONT KEY CHECK menu
This menu is displayed by pressing the following keys: # # .F2F6TEST
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
Key
F1–F7
F8
F9–F13
Key designation
——
EXIT
——
Description
Returns the VTR to the TEST FRONT menu screen.
– 154 –
TEST FRONT KEY CHECK menu
∑ Dial and controls
When the ADJUST control, headphones control or search dial isturned, the number of pulses counted is displayed.
∑ LEDs
Each time the F1 key is pressed, the LEDs on the panel light up insequence and are checked.
∑ Keys
When a key (button) on the panel is pressed, the correspondingkey on the menu screen is highlighted, and the buzzer sounds atthe same time. This makes it possible to confirm that the front microcomputer has recognized the key.
EJECT
SD HD CHANNEL CONDITIONVIDEO AUDIO SERVO HOME ASSEM INSERT
MULTICUE
VIDEO
INF13
7 8 9
4 5 6
1 2 3
0 C T F
F12
F11
F10
F9
F8F7F6F5F4F3F2F1LAUDIO MONITORUNITY
HEADPHONES
PULLOPEN
LEVEL CURSOREXECUTE PREROLL ENTRY REW STOP REC/EDITPLAY
REC INHIBIT
STAND BY FFREVIEW
PREVIEW
R
OUT IN OUT
AUDIOLINE OUT
SHTL JOG VAR
INPUT CHECK REMOTE
ADJUST
POWER
AUTO OFF
ON
OFF
UNITY/VAR
TC/CHR SET UP TEST DIAG
FROM COPY
/ BS
ENT
AUDIO
PULLOPEN
EJECT
SD HD CHANNEL CONDITIONVIDEO AUDIO SERVO HOME ASSEM INSERT
MULTICUE
VIDEO
INF13
7 8 9
4 5 6
1 2 3
0 C T F
F12
F11
F10
F9
F8F7F6F5F4F3F2F1LAUDIO MONITORUNITY
HEADPHONES
PULLOPEN
LEVEL CURSOREXECUTE PREROLL ENTRY REW STOP REC/EDITPLAY
REC INHIBIT
STAND BY FFREVIEW
PREVIEW
R
OUT IN OUT
AUDIOLINE OUT
SHTL JOG VAR
INPUT CHECK REMOTE
ADJUST
POWER
AUTO OFF
ON
OFF
UNITY/VAR
TC/CHR SET UP TEST DIAG
FROM COPY
/ BS
ENT
AUDIO
PULLOPEN
EJECT
SD HD CHANNEL CONDITIONVIDEO AUDIO SERVO HOME ASSEM INSERT
MULTICUE
VIDEO
INF13
7 8 9
4 5 6
1 2 3
0 C T F
F12
F11
F10
F9
F8F7F6F5F4F3F2F1LAUDIO MONITORUNITY
HEADPHONES
PULLOPEN
LEVEL CURSOREXECUTE PREROLL ENTRY REW STOP REC/EDITPLAY
REC INHIBIT
STAND BY FFREVIEW
PREVIEW
R
OUT IN OUT
AUDIOLINE OUT
SHTL JOG VAR
INPUT CHECK REMOTE
ADJUST
POWER
AUTO OFF
ON
OFF
UNITY/VAR
TC/CHR SET UP TEST DIAG
FROM COPY
/ BS
ENT
AUDIO
PULLOPEN
– 155 –
Inserting the IC card
The insertion slot for the IC card is located on the back left of the front panel.Insert the IC card before using the TEST IC CARD menu.
Eject buttonIC card
– 156 –
TEST IC CARD menu
This menu is displayed by pressing the following keys: > F13TEST
Description
User file management takes place using IC card.When the F key is pressed, transfer is made to TEST IC CARDUSER FILE menu.≥There is a load/save function for current (present deck status)
and all registered files.≥When user file is forwarded to deck, whether SYS_H and
SYS_C should be sent together can be selected.
100 CUE_POINTS (MULTI_CUE) can be loaded/saved to ICcard.When the F key is pressed, transfer is made to MULTICUEmenu.≥Whether to send all at once or by page can be selected.
Function available for memory of deck mode, time code and typewhen warning appears.When the F3 key is pressed, the VTR is transferred to the TESTIC CARD ERROR LOG menu.≥Function available for 50-step memory data.≥When memory buffer becomes full, there is a function for
switching to erasure of old material and renewal of newwarning.
≥Function available for memory storage of this data on IC card.≥Function available to monitor IC card data.
Returns the VTR to the TEST menu screen.
IC card is formatted. Please note that all data on the IC card isdestroyed.When the F key is pressed together with C key and F13(FORMAT) key, the IC card is formatted.
Key
F1
F2
F3
F4-F7
F8
F9-F12
F13
Key designation
USER_FIL
MULT_CUE
ERR_LOG
——
EXIT
——
FORMAT
ONoteN
Avoid installing an IC card formatted by this unit in the AJ-HD2000/2700 or any other model.Conversely, avoid installing an IC card formatted by any other model in this unit.The file structure used for these cards is different from one model to another, and this may give rise toproblems in the VTR’s operation.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 157 –
TEST IC CARD USER menu
This menu is displayed by pressing the following keys: > > .F1F13TEST
Description
Calls out IC card user file.(Executes when pressed together with F key.)
Registers IC card user file.(Executes when pressed together with F key.)
Deletes IC card user file.(Executes when pressed together with F key.)
Loads file registered from IC card to deck.(Executes when pressed together with F key.)
Loads file registered from deck to card.(Executes when pressed together with F key.)
Upon transfer of user file from IC card to deck, selects whetherto send card data or to use deck original data for SYSH and SYSSC.ON: Card data are sent.OFF: Original deck data are used.This function is valid only with LOAD (F1) and UP_LD (F5).
Returns the VTR to the TEST IC CARD menu screen.
Sets and releases lock of user file.(Executes when pressed together with F key.)
Upon loading of file registered from IC card to deck, selectswhether to load from file 5 to 10 or to load all files from 1 to 10.FILE 5–10: Loads files 5 to 10 from IC card to deck.ALL: Loads all files from 1 to 10 from IC card to deck.For ALL, press the F key and C key together with F13 key.≥This function is valid only with UP_LD (F5).
Key
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10–F12
F13
Key designation
LOAD
SAVE
DELETE
——
UP_LD
DOWN_LD
W/SYS
EXIT
LOCK
——
TRANS MD
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 158 –
TEST IC CARD MULTI CUE menu
This menu is displayed by pressing the following keys: > > F2F13TEST
Description
Loads file registered from IC card to deck.≥Executes when pressed together with F key.When there is a page on which writing is prohibited, themessage “PROTECTED PAGE” appears and the function is notexecuted. If you still wish to execute the function, either releasethe protected page feature or stop sending to the protectedpage.Upon execution, transfers automatically to deck MULTI CUEmenu.
Loads file registered from deck to IC card to deck. Uponexecution, transfers automatically to deck MONITOR menu.(Executes when pressed together with F key.)
Displays MULTI_CUE data saved in IC card.
At the time of UP_LD from IC card to deck, switch is madebetween either sending all or sending by individual page.ALL: Sends all items.SELECT: Transfers to page select menu upon execution of
UP_LD.
Returns the VTR to the TEST IC CARD menu screen.
Key
F1
F2
F3
F4
F5
F6–F7
F8
F9–F13
Key designation
LP_LD
DOWN_LD
MONITOR
——
TRANSFER
——
EXIT
——
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 159 –
TEST IC CARD MULTI CUE SELECT menu
This menu is displayed when the > > > and keys are pressed together.F1FF2F13TEST
Description
Selected files are loaded from IC card to deck by pressing theUP_LD key after selection of the pages to be forwarded.
Selects the pages to be forwarded.
Returns to TEST IC CARD MULTI CUE menu screen.
Selects the pages to be forwarded.
Key
F1
F2
F3–F7
F8
F9–F13
Key designation
LP_LD
——
EXIT
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 160 –
TEST IC CARD MULTI CUE MONITOR menu
This menu is displayed by pressing the following keys: > > > .F3F2F13TEST
Description
Returns the VTR to the TEST IC CARD MULTI CUE menuscreen.
Key
F1–F2
F3–F7
F8
F9–F13
Key designation
——
1–5Designation of 1–5 cuenumber.
EXIT
6–10Designation of 6–10 cuenumber.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 161 –
TEST IC CARD ERROR LOG menu
This menu is displayed by pressing the following keys: > > F3F13TEST
Description
Loads current memory data from VTR to IC card. In addition, theserial No., software version and operation time are saved. Ifthere is no error log data in any file other than one containing themachine current data (a file saved in the IC card or current dataof the VTR), “ERROR” appears, and the data cannot bedownloaded.≥Executes when pressed together with F key.
Displays the error log data saved in the IC card.After the machine current data (a file saved in the IC card orcurrent data of the VTR) has been downloaded, the error logdata currently stored in the VTR’s memory is displayed.≥Executes when pressed together with F key.
ERROR LOG data saved in IC card is deleted.≥Executes when pressed together with F key.
When warning exceeds buffer capacity, selects whether to eraseold material sequentially and renew.ON: Renews regularly. (The 50th step data is a latest data.)OFF: No renewal when capacity is full.
Returns the VTR to the TEST IC CARD menu screen.
Deletes all the past error log data currently stored in the VTR’smemory and all the error log data currently displayed.When downloading is attempted after executing INITIAL with noerror log data, “ERROR” appears since there is no error log data,and data cannot be downloaded to the IC card while the machinecurrent data can be downloaded.
Key
F1
F2
F3
F4
F5
F6–F7
F8
F9–F12
F13
Key designation
DOWN_LD
MONITOR
DELETE
——
AUTOSTEP
——
EXIT
——
INITIAL
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 162 –
TEST IC CARD ERROR LOG MONITOR menu
This menu is displayed by pressing the following keys: > > > keys are pressed.To check the current log data of the VTR, first download the machine current data, and then monitor the logdata.
F2F3F13TEST
Description
Returns the VTR to the TEST IC CARD ERROR LOG menuscreen.
Key
F1–F7
F8
F9–F13
Key designation
——
EXIT
——
°When more errors are generated than the number that can be displayed on the front panel, use the scroll key to movethe error display.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 163 –
Error messages
Four kinds of error messages are displayed by this VTR.
(1) DIAG menu
A warning mark (W) blinks at the top left of the menu screen when an erroneous setting, failureto verify a condition, warning or other problem that interferes with the use of the VTR has arisen.When the DIAG key is pressed, an error message appears on the screen.
(2) AUTO OFF mode
When a problem occurs in the VTR and it is no longer possible to continue using the VTR with-out fixing it, the AUTO OFF lamp and SYSTEM lamp at the front of the VTR come on, and anerror message appears on the display.
(3) System error
When a problem occurs in the VTR and its operation can no longer be guaranteed, the SYSTEMlamp at the front of the VTR comes on, and an error message appears on the display.
(4) Operation error
When the wrong button or key has been pressed or a wrong value has been input during ope-ration, a message appears at the bottom right of the screen telling the user how to proceed withoperation.
– 164 –
DIAG menu error messages
A warning mark (W) blinks at the top left of the screen when an er-roneous setting, failure to verify a condition, warning or otherproblem that interferes with the use of the VTR has arisen.
If the DIAG key is pressed while a warning is shown, an error message appears on the screen.
There are the following three kinds of DIAG menu screens.
This is the menu that appears initially when the DIAG key is pressed.An error message corresponding to the unmasked (not canceled) warning whichhas just occurred is displayed.
This is the menu that appears when the F2 (MENU MASKED) key is pressed.An error message corresponding to the masked (canceled) warning is displayed.
This is the menu that appears when the F3 (MENU LAST) key is pressed.The error messages for the last three warnings are displayed.
°Any error message is cleared as soon as the error is remedied.
DIAG LAST menu
DIAG MASKED menu
DIAG ACTIVE menu
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 165 –
DIAG ACTIVE menu
When the DIAG key is pressed while the warning mark is displayed, the DIAG ACTIVE menu below appears.
Description
Transfers the VTR to the DIAG MASKED menu screen.
Transfers the VTR to the DIAG LAST menu screen.
Masks (cancels) the warning currently on display in the DIAGACTIVE menu. The error message for the masked warning canbe displayed on the DIAG MASKED menu.
ON: When there is no REF input, STOP lamp blinks.OFF: When there is no REF input, STOP lamp does not blink.
Key
F1
F2
F3
F4
F5
F6
F7–F13
Key designation
——
MENU MASKED
MENU LAST
——
WARNING CANCEL
REF ALM
——
∑ When there are multiple warnings≥Error messages are displayed from item of highest priority.≥All the messages can be viewed sequentially by operating the cursor and the up/down arrow keys.≥Total number of warnings is displayed.
∑ When F6 (REF ALM) key is set to ON, refer to the following table.
OUT_REF
AUTO/INPUT
HD
SD
SD_REF present/absent
Present
Absent
——
Present
Absent
HD_REF present/absent
——
Present
Absent
Present
Absent
——
STOP blinks/glows
Glows
Glows
Blinks
Glows
Blinks
Glows
Blinks
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 166 –
∑ When there are 2 or more canceled (masked) warnings≥Error messages are displayed from item of highest priority.≥All the messages can be viewed sequentially by operating the cursor and the up/down arrow keys.≥Total number of warnings is displayed.
Key
F1
F2
F3
F4
F5
F6–F13
Key designation
MENU ACTIVE
——
MENU LAST
——
WARNING ACTIVATE
——
Description
Transfers the VTR to the DIAG ACTIVE menu.
Transfers the VTR to the DIAG LAST menu.
Releases mask (cancel) of the warning currently on display.Mask of the warning currently on display in the DIAG MASKEDmenu is released.The error message for the warning for which mask was releasedcan be displayed on the DIAG ACTIVE menu.
DIAG MASKED menu
When the [F2] (MENU MASKED) key is pressed on the DIAG ACTIVE or DIAG LAST menu, the DIAGMASKED menu below appears.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 167 –
∑ When 2 or more warnings have occurred≥Error messages are displayed from item of highest priority. ≥All the messages can be viewed sequentially by operating the cursor and the up/down arrow keys.
Key
F1
F2
F3–F6
F7
F8–F13
Key designation
MENU ACTIVE
MENU MASKED
LAST CLEAR
——
Description
Transfers the VTR to the DIAG ACTIVE menu.
Transfers the VTR to the DIAG MASKED menu.
Clears all warnings displayed on the current DIAG LAST menu.All warnings displayed on the current DIAG LAST menu arecleared when the F key is pressed together with the F7 (LASTCLEAR) key.When a new warning is generated, its contents are displayed
DIAG LAST menu
When the F3 (MENU LAST) key is pressed on the DIAG ACTIVE or DIAG MASKED menu, the DIAG LASTmenu below appears.The error messages for the last three warnings are displayed.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 168 –
DIAG error messages
Message
FAN STOP1
FAN STOP2
NO CUE ERASE CURRENT
NO TC ERASE CURRENT
NO FULL ERASE CURRENT
NO CTL ERASE CURRENT
COMP. CPU NOTRESPONDING
VIDEO CONCEAL SW OFF
INNER ECC SW OFF
OUTER VIDEO ECC SWOFF
OUTER AUDIO ECC SWOFF
AUDIO CONCEAL SW OFF
SERVO UNLOCK
CTL NOT DETECTED
LOW RF
AUDIO MUTE
CONCEAL A
CONCEAL V
HIGH ERROR RATE
CTL HEAD CLOGGING
LTC HEAD CLOGGING
LOW RF (REC HEAD)
MISTRACK IN OPTIMIZEDTRACKING DATA
Error description
FAN-1 has stopped. It will continue to operatefor a while but when the internal temperaturerises, its power will be turned off.
FAN-2 has stopped. It will continue to operatefor a while but when the internal temperaturerises, its power will be turned off.
No erase current is flowing to the CUE erasehead.
No erase current is flowing to the TC erasehead.
No erase current is flowing to the full erasehead.
No erase current is flowing to the CTL erasehead.
The compression CPU is not working properly.
The VIDEO CONCEAL SW has been set to OFFdue to the TEST RF menu setting.
The INNER ECC SW has been set to OFF dueto the TEST RF menu setting.
The OUTER VIDEO ECC SW has been set toOFF due to the TEST RF menu setting.
The OUTER AUDIO ECC SW has been set toOFF due to the TEST RF menu setting.
The AUDIO CONCEAL SW has been set to OFFdue to the TEST RF menu setting.
The servo has been disengaged (unlocked).
The CTL signal cannot be played back.
The RF playback level has dropped. Clean thevideo heads.
The audio output has been muted. Check thetape playback mode.
Errors were corrected in the PCM audio data.Check the tape playback mode.
Errors were corrected in the video data. Checkthe tape playback mode.
The error rate has deteriorated.
The CTL head is clogged. Clean the videoheads.
The LTC head is clogged. Clean the videoheads.
The level of the RF envelope played back fromthe rotary recording head has dropped.
Tracking optimizing was not completedsuccessfully.
On-screen display
FAN STOP
FAN STOP
ERASE ERROR
ERASE ERROR
ERASE ERROR
ERASE ERROR
COMP. CPU ERROR
CONCEAL SW OFF
ECC SW OFF
ECC SW OFF
ECC SW OFF
CONCEAL SW OFF
SERVO UNLOCK
CTL NOT DET.
LOW RF
AUDIO MUTE
CONCEAL A
CONCEAL V
HIGH ERROR
CTL HEAD CLOG
LTC HEAD CLOG
LOW RF
OPT ERROR
– 169 –
DIAG error messages
Message
WRONG OPTIMIZEDTRACKING VALUE
SERVO UNLOCKEDBEFORE IN POINT
NO EXTERNAL HD REF
NO EXTERNAL SD REF
NO COLOR BURST IN SD REF
NO STANDARD SCH-RANGE IN REF
NO HD SDI INPUT
CRC ERROR IN HD SDIINPUT
NO EMBEDDED AUDIO(CH1/2/3/4) INPUT
NO EMBEDDED AUDIO(CH5/6/7/8) INPUT
AUDIO (CH1/2/3/4) DATAERROR IN HD SDI INPUT
AUDIO (CH5/6/7/8) DATAERROR IN HD SDI INPUT
NO EMBEDDED LTC
LTC ERROR IN HD SDIINPUT
NO EMBEDDED VITC
VITC ERROR IN HD SDIINPUT
NO SD SDI INPUT
NO EMBEDDED AUDIO INPUT
UNMATCH AUDIORECORDED FORMATCHECK CASSETTE C BIT
UNMATCH AUDIORECORDED FORMATCHECK SYSTEM FORMAT
INPUT DIGITAL AUDIO CH1/2SYNC ERROR CONFIRMINPUT DIGITAL AUDIO
INPUT DIGITAL AUDIO CH3/4SYNC ERROR CONFIRMINPUT DIGITAL AUDIO
Error description
The tracking optimizing operation resulted in adrop in the maximum envelope level by over25%. Check the tape playback mode.
The servo was disengaged (unlocked) before anedit IN point.
The REF signal is not supplied to the HD REFinput connector.
The REF signal is not supplied to the SD REFinput connector.
There is no burst signal in the SD REF signal.
A problem has occurred in SCH of the SD REFsignal.
There is no HD SDI input.
A CRC error has been detected from the HDSDI input signal.
Audio signals are not detected in the HD SDIinput signal.
Audio signals are not detected in the HD SDIinput signal.
A transmission error was detected in the audiosignals of the HD SDI input signal.
A transmission error was detected in the audiosignals of the HD SDI input signal.
The LTC signal is not detected in the HD SDIinput signal.
A transmission error was detected in the LTCsignal of the HD SDI input signal.
The VITC signal is not detected in the HD SDIinput signal.
A transmission error was detected in the VITCsignal of the HD SDI input signal.
There is no SD SDI input.
Audio signals are not detected in the SD SDIinput signal.
Check the C hole (for identifying the 4-channel/8-channel format) on the cassette. Itssetting does not match the system format whichhas been set.
Check the VTR system format. It does not matchC hole (for identifying the 4-channel/8-channel format) setting on the cassette.
A sync error has occurred in the AES/EBUCH1/2 input signals. Check the input signals.
A sync error has occurred in the AES/EBUCH3/4 input signals. Check the input signals.
On-screen display
OPT ERROR
OPT ERROR
HD REF ERROR
SD REF ERROR
SD REF ERROR
SD REF ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
HD SDI ERROR
SD SDI ERROR
SD SDI ERROR
FRMT UNMATCH
FRMT UNMATCH
PCM ERROR
PCM ERROR
– 170 –
DIAG error messages
Message
INPUT DIGITAL AUDIO CH5/6SYNC ERROR CONFIRMINPUT DIGITAL AUDIO
INPUT DIGITAL AUDIO CH7/8SYNC ERROR CONFIRMINPUT DIGITAL AUDIO
INPUT AUDIO CH1/2 CRCCERROR CONFIRM INPUTDIGITAL AUDIO
INPUT AUDIO CH3/4 CRCCERROR CONFIRM INPUTDIGITAL AUDIO
INPUT AUDIO CH5/6 CRCCERROR CONFIRM INPUTDIGITAL AUDIO
INPUT AUDIO CH7/8 CRCCERROR CONFIRM INPUTDIGITAL AUDIO
INPUT DIGITAL AUDIO CH1/2PARITY ERROR CONFIRMINPUT DIGITAL AUDIO
INPUT DIGITAL AUDIO CH3/4PARITY ERROR CONFIRMINPUT DIGITAL AUDIO
INPUT DIGITAL AUDIO CH5/6PARITY ERROR CONFIRMINPUT DIGITAL AUDIO
INPUT DIGITAL AUDIO CH7/8PARITY ERROR CONFIRMINPUT DIGITAL AUDIO
RECEIVED INVALIDCOMMAND FROM RS-422PORT
SUM-CHECK ERROR INRECEIVED COMMANDFROM RS-422 PORT
PARITY ERROR INRECEIVED COMMANDFROM RS-422 PORT
FRAMING ERROR INRECEIVED COMMANDFROM RS-422 PORT
OVER-RUN ERROR INRECEIVED COMMANDFROM RS-422 PORT
RS-422 COMMUNICATIONSTOP BY TIME OUT
RECEIVED INVALIDCOMMAND FROM RS-232CPORT
Error description
A sync error has occurred in the AES/EBUCH5/6 input signals. Check the input signals
A sync error has occurred in the AES/EBUCH7/8 input signals. Check the input signals.
A CRCC error has occurred in the AES/EBUCH1/2 input signals. Check the input signals.
A CRCC error has occurred in the AES/EBUCH3/4 input signals. Check the input signals.
A CRCC error has occurred in the AES/EBUCH5/6 input signals. Check the input signals.
A CRCC error has occurred in the AES/EBUCH7/8 input signals. Check the input signals.
A parity error has occurred in the AES/EBUCH1/2 input signals. Check the input signals.
A parity error has occurred in the AES/EBUCH3/4 input signals. Check the input signals.
A parity error has occurred in the AES/EBUCH5/6 input signals. Check the input signals.
A parity error has occurred in the AES/EBUCH7/8 input signals. Check the input signals.
An undefined command has been received.
A sum check error has occurred in the receivedcommand.
A parity error has occurred in the receivedcommand.
A framing error has occurred in the receivedcommand.
An overrun error has occurred in the receivedcommand.
A timeout error has occurred.
An undefined command has been received.
On-screen display
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
PCM ERROR
RS-422 ERROR
RS-422 ERROR
RS-422 ERROR
RS-422 ERROR
RS-422 ERROR
RS-422 ERROR
RS-232C ERROR
– 171 –
DIAG error messages
Message
SUM-CHECK ERROR INRECEIVED COMMANDFROM RS-232C PORT
PARITY ERROR INRECEIVED COMMANDFROM RS-232C PORT
FRAMING ERROR INRECEIVED COMMANDFROM RS-232C PORT
OVER-RUN ERROR INRECEIVED COMMANDFROM RS-232C PORT
RS-232C COMMUNICATIONSTOP BY TIME OUT
RECEIVED INVALIDCOMMAND FROMVA_CONT PORT
SUM-CHECK ERROR INRECEIVED COMMANDFROM VA_CONT PORT
PARITY ERROR INRECEIVED COMMANDFROM VA_CONT PORT
FRAMING ERROR INRECEIVED COMMANDFROM VA_CONT PORT
OVER-RUN ERROR INRECEIVED COMMANDFROM VA_CONT PORT
EXT LTC NOT READ
EXT VITC NOT READ
LTC IN TAPE NOT READ
IC CARD LOW BATTERY
Error description
A sum check error has occurred in the receivedcommand.
A parity error has occurred in the receivedcommand.
A framing error has occurred in the receivedcommand.
An overrun error has occurred in the receivedcommand.
A timeout error has occurred.
An undefined command has been received.
A sum check error has occurred in the receivedcommand.
A parity error has occurred in the receivedcommand.
A framing error has occurred in the receivedcommand.
An overrun error has occurred in the receivedcommand.
There is a problem with the EXT TC input.
There is a problem with the EXT VITC input.
The LTC signal is not played back.
The IC card battery has a low remaining charge.Replace the card.
On-screen display
RS-232C ERROR
RS-232C ERROR
RS-232C ERROR
RS-232C ERROR
RS-232C ERROR
VA-CONT ERROR
VA-CONT ERROR
VA-CONT ERROR
VA-CONT ERROR
VA-CONT ERROR
TC ERROR
TC ERROR
TC ERROR
CARD LOW BATT
– 172 –
AUTO OFF error messages
If a problem has occurred and the VTR cannot continue operating or the mechanism or tape may be damagedby continued operation, the AUTO OFF lamp on the VTR’s front panel come on, the buzzer sounds, and anerror message appears on the screen. In this situation, stop operating the VTR, and proceed to fix the problem.
≥With the exception of the DEW error message, the original screen will not be restored unless the power isturned off and then back on again.
≥If the error persists even after the power has been turned off and then back on again, the problem is serious,and the VTR will need to be repaired or some of its parts replaced. Immediately turn off the power, removethe power plug from the power outlet, and contact your dealer. Bear in mind that continued operation mayexacerbate the existing problem and/or cause other unforeseen problems.
AUTO OFF lamp
AUTO OFF occurs mainly when the tape transport system is experiencing problems.When AUTO OFF has occurred, open the VTR’s top panel, check that the tape in use has been proper-ly installed in the transport system, and then turn on the power. If the tape in use has become disen-gaged from the transport system, contact your dealer.
EJECT
POWER
AUTO OFF
ON
OFF
AUTO OFF
CASSETTE UNLOAD FAIL
POWER OFF
– 173 –
AUTO OFF error messages
Message
CPU TAPE HANDLETROUBLE
CPU (SERVO SYS) COMM.TROUBLE
CASSETTE PHOTOSENSOR TROUBLE
DETECTION SWITCH FAIL(A)
DETECTION SWITCH FAIL(B)
DETECTION SWITCH FAIL(C)
ROTATE-RANGE OVER
CAPSTAN NOT ROTATE
TAPE TENSION ERROR
TAPE TENSION OVER-RANGE IN SHTL
REEL DIRECTIONUNMUTCH
WIND-UP REEL NOTROTATE
NO S-REEL FG PULSE
NO T-REEL FG PULSE
CASSETTE UNLOAD FAIL
SUB UNLACING FAIL
MAIN UNLACING FAIL
DEW
Error description
The CPU is not working properly due to an errorin the interrupt processing, etc.
A problem has occurred in communicationbetween the servo microcomputer and systemcontrol microcomputer.
A problem with the LED has been detected.
There is a problem with the cassette’s 3-stageswitch (A) (on the cylinder side).
There is a problem with the cassette’s 3-stageswitch (B) (middle position).
There is a problem with the cassette’s 3-stageswitch (C) (on the cassette insertion slot side).
A problem with the cylinder’s rotation has beendetected.
A problem with the capstan’s rotation has beendetected.
A tape tension error has been detected. (Pinchroller ON status) Check the tape transportsystem.
A tape tension error has been detected. (Reeldrive status with pinch roller OFF) Check thetape transport system.
A discrepancy in the rotational directions of thesupply and take-up reels has been detected.Check the tape transport system.
Defective rotation of the take-up reel has beendetected. (During capstan drive) Check the tapetransport system.
Trouble with the rotation of the supply reel hasbeen detected.
Trouble with the rotation of the take-up reel hasbeen detected.
A problem with the cassette “up” operation hasoccurred. Check the tape transport system.
A problem with the sub-unloading operation hasoccurred. Check the tape transport system.
A problem with the main unloading operationhas occurred. Check the tape transport system.
The formation of condensation has beendetected. Refrain from inserting a cassette sincethis condition may cause the tape to adhere tothe inside parts, etc., thereby damaging it.
On-screen display
SYSCON ERROR
SERVO ERROR
MECHA ERROR
MECHA ERROR
MECHA ERROR
MECHA ERROR
SERVO ERROR
SERVO ERROR
SERVO ERROR
SERVO ERROR
SERVO ERROR
SERVO ERROR
SERVO ERROR
SERVO ERROR
MECHA ERROR
MECHA ERROR
MECHA ERROR
MECHA ERROR
– 174 –
SYSTEM error messages
When a problem has occurred in the VTR and its operation can no longer be guaranteed, the system errorlamp comes on, the buzzer sounds, and an error message appears on the screen.
In this situation, stop operating the VTR immediately, and proceed to fix the trouble.
≥With system errors, the original screen will be restored when the power switch is turned off and the cause ofthe error is eliminated.
EJECT
SD HD CHANNEL CONDITIONVIDEO AUDIO SERVO HOME ASSEM INSERT
MULTICUE
VIDEO
INF13
7 8 9
4 5 6
1 2 3
0 C T F
F12
F11
F10
F9
F8F7F6F5F4F3F2F1LAUDIO MONITORUNITY
HEADPHONES
PULLOPEN
LEVEL CURSOREXECUTE PREROLL ENTRY REW STOP REC/EDITPLAY
REC INHIBIT
STAND BY FFREVIEW
PREVIEW
R
OUT IN OUT
AUDIOLINE OUT
SHTL JOG VAR
INPUT CHECK REMOTE
ADJUST
POWER
AUTO OFF
ON
OFF
UNITY/VAR
TC/CHR SET UP TEST DIAG
FROM COPY
/ BS
ENT
AUDIO
PULLOPEN
SYSTEM ERROR
L1 BOARD NOT RESPONDING
– 175 –
SYSTEM error messages
Message
AV NOT RESPONDING
SYSCON NOTRESPONDING
S2 BOARD NOTRESPONDING
S3 BOARD NOTRESPONDING
S4 BOARD NOTRESPONDING
S5 BOARD NOTRESPONDING
L1 BOARD NOTRESPONDING
L2 BOARD NOTRESPONDING
CASSETTE LOAD FAIL
SUB LACING FAIL
MAIN LACING FAIL
HUB POSITION
Error description
The AV microcomputer is not working properly.The reference signals from the S5 printed circuitboard may not be the prescribed ones or somesimilar kind of problem is to blame.
A problem has occurred in communicationbetween the system control microcomputer andfront microcomputer.
The S2 printed circuit board has been removed.
The S3 printed circuit board has been removed.
The S4 printed circuit board has been removed.
The S5 printed circuit board has been removed.
The L1 printed circuit board has been removed.
The L2 printed circuit board has been removed.
A problem has occurred during the cassette“down” operation.
A problem was detected during the sub-loadingoperation, and the cassette was ejected. Checkthe tape transport system.
A problem was detected during the main loadingoperation, and the cassette was ejected. Checkthe tape transport system.
The reel hub position does not match thecassette size. The cassette was ejected as aresult.
On-screen display
SYSTEM ERROR
SYSTEM ERROR
SYSTEM ERROR
SYSTEM ERROR
SYSTEM ERROR
SYSTEM ERROR
SYSTEM ERROR
SYSTEM ERROR
MECHA ERROR
MECHA ERROR
MECHA ERROR
MECHA ERROR
– 176 –
Operation messages
In the majority of cases, when a mistake has been made in operating a button or key during automatic editing,a message appears at the bottom right of the screen (above the tape speed display) telling the user how toproceed with operation.≥The message is automatically cleared after it has been displayed for several seconds.
F13
F12
F11
F10
F9
F8F7F6F5F4F3F2F1
– 177 –
Operation messages (in AUTO EDIT mode)
No.
350
351
352
353
354
355
356
357
359
360
361
362
363
Message
NO CASSETTE
NO PRESET
NO IN POINT
NO PLY’ R MODE
NOT REC’ R MODE
NEGATIVE DURATION
INVALID DATA
PLAYER LOCAL
REC INHIBITED
W/PLAYER NOT SET
BOT
EOT
SHIFT TC FOR CF EDIT
Description of error/problem
A cassette tape has not been inserted.
The editing channel has not been selected in the editing mode orduring insert editing.
The edit point data required for editing has not been entered.
The mode in which the player is to be controlled has not beenestablished.Set it correctly on the INSERT (or ASSEMBLE) AUTO EDITmenu.
The mode in which the recorder is to be controlled has not beenestablished. Set it correctly on the INSERT (or ASSEMBLE) AUTO EDITmenu.
The time data of the edit OUT point is ahead of the time data ofthe edit IN point.
Illegal or invalid data has been input.
The connected player is in the LOCAL mode.
An attempt has been made to execute automatic editing whilethe recording inhibit mode is set. Select the HOME menu settingand operate the recording inhibit pins on the cassette tape torelease the REC INHIBIT mode.
A mode in which the player can be used has not beenestablished.Check the F1 (MODE) key setting on the INSERT (orASSEMBLE) AUTO EDIT SET UP menu.
The tape is at its end.
The tape is at its start.
The TC value used in the CF lock mode is incorrect
– 178 –
Screen saver function
This function is designed to prolong the service life of the VTR’s large display screen.The screen’s life may be shortened when the screen continuously displays menu screens on which no move-ment is occurring.Consequently, when the same menu screen on which no movement occurs is displayed continuously on thedisplay screen for 5 or more minutes, it is automatically replaced with the screen saver screen shown below.
The logo displayed moves around the screen.
ONotesN
≥The screen saver function is activated only when a menu screen on which absolutely no movement occurshas been displayed continuously for 5 or more minutes. If a function key is pressed at some point, it will notbe activated unless another 5 minutes have elapsed from the moment when the key was pressed.
≥Neither will the screen saver function be activated when the time code value on a menu screen has changedduring recording, playback, etc. even if nothing else has changed.
Menu
HOME HOME SET UP VIDEO IN VIDEO OUT HD
– 179 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
OUTPUT
FREEZE
EJT CTL
TC/CTL
TC/UB
(CTL) CLR(TC)(UB)
TC HOLD
SET UP
REC INN
Selectionitem
TAPEEE
ONOFF
RESETHOLD
TCCTL1CTL2
TCUB
RESET
TransfersVTR tomenuscreen.
FREENRML.RECALL
Settingitem
SYNC PLY
AT PLY
PRG PLAY
PRG PLAY
CAP LOCK
TAPEMODE
EXIT
PREROLL
STILL
STBY OFF
Settingitem
INPUT
INT SG
INT SG
INPUT
Settingitem
Y
PB
PR
BLACK.L
SET UP
SD
CONVERT
Selectionitem
ONOFF
FIELDFRAME1FRAME2
FINECOARSE
Variable upto 5% inincrementsset by theF3 key0.0 %
8F AUTO(24/50) (4F)8F FORCE(24/50) (4F)2F
HD.STOPHLF LOAD
nSEC1RnR30nl5
1/3/30 SEC1/3/5 MIN
1/3/30 SEC1/3/16 MIN¶
Selectionitem
DIGITALINT SG
75 % CB100 % CBRAMPMULT-BSTBLACKSIF PLLSIF EQSMPTE CB
75 % CB100 % CBRAMPMULT-BSTBLACKSIF PLLSIF EQSMPTE CB
DIGITALINT SG
Selectionitem
UNITYVAR(can bechangedusing theADJUSTcontrol)
UNITYVAR
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
– 180 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
LINCONV
SERIALSYSPHASE
INTERP.
EXIT
STATE
Selectionitem
ONOFF
n1375SAMPLEn1320SAMPLEn1100SAMPLEn825SAMPLE
AUTOOFF
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
EE_MODE
EXIT
STATE
Settingitem
Y
PB
PR
BLACK.L
HD
CONVERT
CMPT
SDI
Settingitem
COMBFIL
SYS SC
SYS H
INTERP.
EXIT
7.5 %SET UP
LINE BLK
STATE
Selectionitem
NORMALTHROUGH
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Selectionitem
UNITYVAR(j¶–i3 dB)
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Selectionitem
ONOFF
UNITYVAR
j858–i858j864–i864
AUTOOFF
TransfersVTR tomenuscreen.
ONOFF
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Menu
VIDEO OUT VIDEO OUT HD VIDEO OUT SD VIDEO OUT SDHD SET UP SET UP STATE SET UP COMPSITE
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
– 181 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
EE_MODE
EXIT
STATE
Selectionitem
NORMALTHROUGH
TransfersVTR tomenuscreen.
Settingitem
SERIALSYSPHASE
SYSPHASE
INTERP.
EXIT
LINE BLK
STATE
Settingitem
EXIT
ALL ON
ALL OFF
LINE BLK
Settingitem
EE_MODE
EXIT
STATE
Selectionitem
FINECOARSE
n2H
AUTOOFF
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Selectionitem
TransfersVTR tomenuscreen.
Selectionitem
NORMALTHROUGH
TransfersVTR tomenuscreen
Menu
VIDEO OUT SD SET UP VIDEO OUT SD VIDEO OUT SET VIDEO OUT SDCMPST STATE SET UP SDI UP LINE BLK SET UP SDI STATE
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
– 182 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
HD_TO_SD
SD_TO_HD
HD_TO_HD
HD
SD
Selectionitem
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
MODE
RESPONSE
ENHANCE
EXIT
Settingitem
MODE
RESPONSE
ENHANCE
EXIT
Settingitem
RESPONSE
ENHANCE
EXIT
Selectionitem
FIT_HFIT_VFIT_HV14:913:9
STANDARDWIDENARROW
6 dB3 dB1.5 dB0 dB
Selectionitem
FIT_HFIT_VFIT_HV
STANDARDWIDENARROW
6 dB3 dB1.5 dB0 dB
Selectionitem
STANDARDWIDENARROW
6 dB3 dB1.5 dB0 dB
Menu
VIDEO OUT CONVERTVIDEO OUT CON- VIDEO OUT CON- VIDEO OUT CON-VERT HD_TO_SD VERT SD_TO_HD VERT HD_TO_HD
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
– 183 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
CH-1
CH-2
CH-3
CH-4
CUE
PCM
CUE
SET UP
CH-MIX
(CH-5)°
(CH-6)°
(CH-7)°
(CH-8)°
Selectionitem
UNITYVAR
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
(UNITY)°(VAR)°
Settingitem
CH-1
CH-2
DIGITAL
CH-3
CH-4
DIGITAL
(DIGITAL)°
EXIT
(CH-5)°
(CH-6)°
(DIGITAL)°
(CH-7)°
(CH-8)°
Settingitem
CH-1(With D.MIX)
CH-2(With D.MIX)
CH-3(With D.MIX)
CH-4(With D.MIX)
EXIT
CUE
(CH-5)°
(CH-6)°
(CH-7)°
(CH-8)°
Settingitem
INT SGMD
PEAKHOLD
SCALE
EXIT
DATAADV
STYLE
Selectionitem
ANALOGDIGITALINT SG
ANALOGDIGITALINT SG
AESSERIAL
ANALOGDIGITALINT SG
ANALOGDIGITALINT SG
AESSERIAL
(AES)°(SERIAL)°
(ANA_CH1)°(DIGITAL)°(INT SG)°
(ANA_CH2)°(DIGITAL)°(INT SG)°
(AES)°(SERIAL)°
(ANA_CH3)°(DIGITAL)°(INT SG)°
(ANA_CH4)°(DIGITAL)°(INT SG)°
Selectionitem
SOURCETAPEOFF
D-MIXLINEAUTO
SOURCETAPEOFF
Selectionitem
TONESILENCE
ONOFF
FINEFULL
0–1Fr
PCMDATA
Menu
AUDIO INAUDIO IN PCM AUDIO IN CUE AUDIO ININPUT SELECT INPUT SELECT SET UP
*: Items and settings in parentheses apply when the 8-channel format is used.
– 184 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
SELECT
CH-MIX(ON)
CH-MIX(OFF)
EXIT
Selectionitem
CH1–CH4CH5–CH8
ONOFF
ONOFF
Settingitem
CH-1
CH-2
CH-3
CH-4
CUE
MONITOR
EXIT
SDIASIGN
(CH-5)°
(CH-6)°
(CH-7)°
(CH-8)°
Settingitem
MODE
L CH
R CH
A MONI
EXIT
R CH
L CH
MODE
Settingitem
A/VPHASE
JOGPROC
VARPROC
PB FADE
PB OUT
PEAKHOLD
SCALE
EXIT
DATA_ADV
STYLE
STATE
Selectionitem
UNITYVAR
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
(UNITY)°(VAR)°
Selectionitem
SHTLVAR/SHTL
OFFON
OFFON
UNITYVAR
ONOFF
ADDAVERAGE
Selectionitem
UNITYVAR
ONOFF
ONOFF
ONOFF
INSTANTDELAYED
ONOFF
FINEFULL
0–1Fr
PCMDATA
TransfersVTR tomenuscreen.
Menu
AUDIO INAUDIO OUT
AUDIO OUT AUDIO OUTCH-MIX MONITOR SET UP
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
*: Items and settings in parentheses apply when the 8-channel format is used.
– 185 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
EE_MODE
EXIT
Selectionitem
NORMALTHROUGH
Settingitem
HD_TO_HDCH1–4
(HD_TO_HD)(CH5–8)
HD_TO_SDCH1–4
EXIT
SD_TO_HDCH5–8
SD_TO_HDCH1–4
SD_TO_HDCH1–4
Settingitem
SOURCE
TC SLAVE
UB SLAVE
RUN MD
DF MD
(CF BIT)
SET UP
CONVERT
TCR
SUPER
SUPER ER
CHARTYPE
Settingitem
LTC ADV
COUNTER
TCG OUT
EXIT
VITC.L
VITC
VITC
LTC
Selectionitem
CH1–4CH5–8OFF
(CH1–4)(CH5–8)(OFF)
CH1–4CH5–8OFF
CH1–4CH5–8OFF
CH1–4CH5–8OFF
CH1–4CH5–8OFF
Selectionitem
INTEXT LTCS LTCS VITC
AUTOPRESETSLAVEDIRECT
ONOFF
REC RUNFREE RUN
ONOFF
(ON)(OFF)
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
LTCAUTOVITC
TCTC. ST.TC. UBTC. ST. RTOFF
ONOFF
REVERSEINTENSE
Selectionitem
EDIT_RECRECEDITOFF
FREEHOLD
MOMNTLATCH
TransfersVTR tomenuscreen.
ONOFF
ONOFF
ONOFF
Menu
AUDIO OUT AUDIO OUT SDITC/CHR
TC/CHRSET UP STATE ASIGN SET UP
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
– 186 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
EXIT
VTIC.L
Selectionitem
Settingitem
TC SYNC
DF MODE
EXIT
SD SUPER
HD SUPER
LTC OUT
Selectionitem
DF NDF
CONVERTORIGINAL
CONVERTORIGINAL
CONVERTORIGINAL
Settingitem
1
2
3
4
5
PROTECT
SET UP
6
7
8
9
10
Selectionitem
ONOFF
TransfersVTR tomenuscreen.
Settingitem
AUTOSTEP
PAG MODE
PAG CLR
ALL CLR
EXIT
CLUTCH
MAX SP.
AUTO FRZ
CUE_ROLL
Selectionitem
ONOFF
ONOFF
ONOFF
j1( )i2j1( )i10( )i1
ONOFF
nSEC1RnR30nl5
Menu
TC/CHRTC/CHR CONVERT MULTI CUE
MULTI CUESET UP VITC. L SET UP
– 187 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
SET UP
INSERT/ASSEMBLE
AUTOEDIT
CH SELECT(displayedduringINSERTediting only)
Selectionitem
TransfersVTR tomenuscreen.
ONOFF
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
TIMING
EXIT
ERR. STP
TRACKING
CAP LOCK
FD TIME
MODE
Selectionitem
F1F2F1/F2
ONOFF
VARFIXOPT. ONCEOPT. AUTO
4F AUTO4F FORCE2F (1080/59i)8F AUTO8F FORCE
5/10/15/20/25/50100 ms
X FADECUTV FADE
Settingitem
LAST X
LAST ED
W/PLYR
VAR MEMO
PLYR SEL
R/P SEL
TRIM
SET UP
INSERT/ASSEMBLE
SPLIT
MANUALEDIT
CH SELECT(displayedduringINSERTediting only)
Selectionitem
LOADOFF
LOADOFF
ONOFF
ONOFF
PLYR-1PLYR-2
PLAYERRECORDER
ONOFF
TransfersVTR tomenuscreen.
ONOFF
ONOFF
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
TIMING
V PREV
A PREV
PLYR-SYNC
PREROLL
POSTROLL
REACTION
EXIT
DLY STRT
TRACKING
CAP LOCK
FD TIME
MODE
Selectionitem
F1F2F1/F2
VVVVBV
SSSSMS
ONOFF
nSEC1RnR30nl5
nSEC1RnR30nl2
nFR0RnR25nl0
nn frames1RnR30nl0
VARFIXOPT. ONCEOPT. AUTO
4F AUTO4F FORCE2F (1080/59i)8F AUTO8F FORCE
5/10/15/20/25/50/100 ms
X FADECUTV FADE
Menu
MANUAL EDITMANUAL EDIT
AUTO EDITAUTO EDIT
SET UP SET UP
– 188 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
VIDEO
CH-1
CH-2
CH-3
CH-4
CUE
TC
SET UP
CH-5
CH-6
CH-7
CH-8
CHSELECT
Selectionitem
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
TransfersVTR tomenuscreen.
ONOFF
ONOFF
ONOFF
ONOFF
TransfersVTR tomenuscreen.
Settingitem
HOME
MAN EDIT
AUTO EDIT
SYSTEM
TC/CHR
AUDIO IN
AUDIO OUT
INTERFACE
PANEL
USER
ENGINEER
Selectionitem
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
P-2
RS-232C
PARA
AV CONT
FF/REWMAX SP.
DEV ID
(PREREAD)(480/59i)
EXIT
UBPRESET
VAR LIM
V LEVCNT
(R. PANEL)
(F. PANEL)
Selectionitem
MODE-1MODE-2MODE-3MODE-4OFF
ONOFF
ONOFF
ONOFF
32/50
ID-1ID-2ID-3USER
(VIDEO)(AUDIO)(A&V)
L&VLTCVITC
ONOFF
NORMALHDSDBOTH
(ENABLE)(DISABLE)
(ENABLE)(DISABLE)
Settingitem
SOUNDKEY
SOUNDALARM
JOG MAXSP
SHTL L/C/R
SHTLk8, k4
SHTLMAX SP
A. SCALE
EXIT
TC INPUT
UNITY
OP MAP
VAR MAXSP
VARCLUTCH
Selectionitem
OFFHIGHLOW
OFFHIGHLOW
j2( )i2j1( )i1j1( )i2
ONOFF
OFFk8k8, k4k4
16/32/50
j20 (18) dB0dB
STANDARDREVERSE
ALL A&VAUDIO PB
TransfersVTR tomenuscreen.
j1( )i2j1( )i10( )i1
ONOFF
Menu
INSERT MANUAL/AUTOSET UP
INTERFACE PANEL SET UP
EDIT CH SELECT SET UP
– 189 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
VIDEO
AUDIO
TRACKING
MON SEL
MAPMODE
FUNCTION(displayedduringINSERTediting only)
EJECT(displayedduringINSERTediting only)
EXIT
REMOTE/LOCAL
Selectionitem
ONOFF
ONOFF
ONOFF
ONOFF
ALLSELECT
ENABLEDISABLE
ENABLEDISABLE
TransfersVTR tomenuscreen.
Settingitem
LOAD
SAVE
DELETE
POWER UP
EXIT
LOCK
PASS WORD
Selectionitem
LASTFACTORY1–10
Settingitem
FREQ
VIDEO
AUDIO
HD SDI
HD MONI
SD_SDI
EXIT
A. REC.GDR
PB AUTO
Selectionitem
59.9423.982450
1080I525I720I
24 bit/8CH20 bit/4CH
1080/23.98PsF(1080/24PsF)1080/59.94I(1080/60I)720/59.94P(720/60P)
1080/23.98PsF(1080/24PsF)1080/59.94I(1080/60I)
525I525P
CST. C. BITFREE
ONOFF
Settingitem
EXIT
OPERATION
Selectionitem
TransfersVTR tomenuscreen.
Menu
OP MAPUSER SET UP SYSTEM SET UP ENGINEER SET UP
REMOTE/LOCAL
– 190 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
EJECTLED
EXIT
ACCEL
KNEE
Selectionitem
MODE-1MODE-2
MAXMIDDLEMIN
08152030
Settingitem
RF
AUDIO
MECHA
SYSTEM
FRONT
SERVO
IC CARD
Selectionitem
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
ECC SMPL
METER
LOAD
MODE
CH
EXIT
AT HEIGT
ADJ RF
ADJ SEL
HEAD CLN
Selectionitem
SLOWFAST
ERRORENV
ENVR/PCONFITCEYE
CH0CH1CH2CH3
(F6 displaychanges)(F7)
D5 EQD5 RECD5 PLL
Settingitem
CH-1
CH-2
CH-3
CH-4
CUE
MONI. L
MONI. R
EXIT
REF. LEV
IMPED.
OUT LEV.
IN LEV.
Selectionitem
Menu
OPERATION ENGINEERTEST RF TEST AUDIO TEST
SET UP
– 191 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
MODE
C.SIZE
SENSOR
EXIT
Selectionitem
NORMALNO-TAPE
Settingitem
EXIT
Selectionitem
Settingitem
TORQUE
DATASEND
MEASURE
AT
METER
PG SHIFT
ADJ RATE
EXIT
MECHA
TRACKING
BIMORPHINIT
ADJENABLE
Selectionitem
OFFLOADING
ERRORENV
FINECOARSE
VARFIXOPT. ONCEOPT. AUTO
Settingitem
PANEL
KEYCHECK
EXIT
Selectionitem
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Menu
MECHA TEST SYSTEM TEST SERVO TEST TEST FRONT
– 192 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
EXIT
Selectionitem
Settingitem
MODE
EXIT
Selectionitem
Settingitem
USER_FIL
MULT_CUE
ERR_LOG
EXIT
FORMAT
Selectionitem
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
TransfersVTR tomenuscreen.
Settingitem
LOAD
SAVE
DELETE
UP_LD
DOWN_LD
W/SYS
EXIT
LOCK
TRNS MD
Selectionitem
Menu
TEST FRONT TEST FRONTTEST IC CARD
TEST IC CARDKEY CHECK PANEL USER
– 193 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
UP_LD
DOWN_LD
MONITOR
TRANSFER
EXIT
Selectionitem
Settingitem
UP_LD
EXIT
Selectionitem
Settingitem
01
02
03
04
05
EXIT
06
07
08
09
10
Selectionitem
Settingitem
DOWN_LD
MONITOR
DELETE
AUTO STOP
EXIT
INITIAL
Selectionitem
Menu
TEST IC CARD TEST IC CARD MULTI CUE MONITOR TEST IC CARDMULTI CUE MULTI CUE SELECT TEST IC CARD ERR LOG
– 194 –
List of menu screen displays
The underlined setting in the selection item column denotes the mode initially set.
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
FUNCkey
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
Settingitem
EXIT
Selectionitem
Settingitem
Selectionitem
Settingitem
Selectionitem
Settingitem
Selectionitem
Menu
TEST IC CARDERR LOG MONITOR
– 195 –
INDEX
[A] Menu/function keys/pages
Alarm tone setting PANEL SET UP/F2/119Assemble editing: Automatic editing AUTO EDIT/F12/99
Manual editing MANUAL EDIT/F12/87AT head hysteresis removal SERVO TEST/F12/149AT playback switching HOME SET UP/F2/18AUDIO FADE: Fade editing
(during automatic editing) AUTO EDIT SET UP/F12–F13/109Fade editing
(during manual editing) MANUAL EDIT SET UP/F12–F13/92, 97Fade playback AUDIO OUT SET UP/F4/63
AUDIO MONITOR: Mixed monitor channel selection AUDIO OUT MONITOR/F11–F12/61Monitor volume adjustment AUDIO OUT MONITOR/F7/61
AUDIO OUT SDI ASSIGNHD TO HD AUDIO OUT SDI ASIGN/F1, F2/69HD TO SD AUDIO OUT SDI ASIGN/F4/69SD TO HD AUDIO OUT SDI ASIGN/F9, F10/69SD TO SD AUDIO OUT SDI ASIGN/F13/69
AUDIO/VIDEO delay adjustment AUDIO OUT SET UP/F1/63, 65AUDIO: Analog input reference level setting mode AUDIO TEST/F13/144
Analog input/output signal reference level setting AUDIO TEST/F1–F5/144
Analog output reference level setting mode AUDIO TEST/F12/144Audio-to-video output adjustment AUDIO OUT SET UP/—/65Channel input selection AUDIO IN PCM INPUT SELECT/F1–F7,
F9–F13/49, 50Channel mixing AUDIO IN CH-MIX SELECT/F6–F7/55–57Channel ON/OFF MANUAL EDIT CH SELECT/F2–F5, F9–F12/89DATA ADV amount AUDIO IN SET UP/F9/54
AUDIO OUT SET UP/F9/63Input signal recording level adjustment AUDIO IN/F1–F5, F10–F131/47Level meter scale setting PANEL SET UP/F7/119Level meter scale switching AUDIO IN SET UP/F7/54
AUDIO OUT SET UP/F7/63Monitor connector output mixed signal switching AUDIO OUT MONITOR/F11–F12/61Monitor volume adjustment AUDIO OUT MONITOR/F7/61Output SDI channel assignment AUDIO OUT SDI ASIGN/F1, F2, F4, F9, F10,
F13/69Output signal level adjustment AUDIO OUT/F1–F5, F10–F131/59Peak hold AUDIO IN SET UP/F6/54
AUDIO OUT SET UP/F6/62Split editing AUTO EDIT/F10/52, 53, 107State AUDIO OUT SET UP STATE/—/66, 67
AUTO OFF error messages AUTO OFF/—/176, 177Automatic editing AUTO EDIT/F12/99Automatic file call at power-on setting USER SET UP/F5/125A/V phase adjustment AUDIO OUT SET UP/F1/63, 65
– 196 –
INDEX
[B] Menu/function keys/pages
Black level adjustment VIDEO OUT HD/F4/25VIDEO OUT SD/F4/31
[C]Capstan servo lock setting MANUAL EDIT SET UP/F11/92
AUTO EDIT SET UP/F11/109Automatic cursor movement MULTI CUE SET UP/F1/86Changing and clearing MULTI CUE/—/84Clearing all cue data MULTI CUE SET UP/F5/86Clearing cue data on a page MULTI CUE SET UP/F3/86Cursor movement ON/OFF MULTI CUE SET UP/F2/86Entering MULTI CUE/—/83, 84Number designation MULTI CUE/F1–F5, F9–F13/82Preroll time selection MULTI CUE SET UP/F13/86Protect MULTI CUE/F6/82, 83
Channel assignment INTERFACE SET UP/—/117AUDIO OUT SDI ASIGN/F1–F2, F4–F5, F9–F10,F12–F13/69
Control signal resetting HOME/F6/14Cue audio: Channel ON/OFF AUDIO IN CUE INPUT SELECT/F1–F4, F10–F13/52
D MIX signal selection AUDIO IN CUE INPUT SELECT/F9/52Editing ON/OFF MANUAL EDIT/F9/87
[D]Device ID setting, alignment with controller INTERFACE SET UP/F6/113DIAG error messages DIAG/—/163–171
[E]Editing: Data (all data input last) call AUTO EDIT/F2/99, 102
Data (edit data input last) call AUTO EDIT/F1/99, 102Delay (startup from playback command) setting AUTO EDIT SET UP/F9/109, 110Duration AUTO EDIT/—/100Edit inhibit (EDIT REC INHIBIT) setting during
manual editing MANUAL EDIT SET UP/—/93, 94Edit point entry AUTO EDIT/—/100–102Edit point recording field selection
(during automatic editing) setting AUTO EDIT SET UP/F1/108Edit point recording field selection
(during manual editing) setting MANUAL EDIT SET UP/F1/91Edit point trimming AUTO EDIT/F7/99, 101
– 197 –
INDEX
[E] Menu/function keys/pages
Editing: Editing channel selection during automatic editing INSERT AUTO EDIT CH SELECT/F1–F7,F9–F12/106
Editing channel selection during manual editing INSERT MANUAL EDIT CH SELECT/F1–F7,F9–F12/89
Editing mode selection during automatic editing AUTO EDIT/F9/99Editing mode selection during manual editing MANUAL EDIT/F9/87Postroll time setting AUTO EDIT SET UP/F6/108Preroll time selection HOME SET UP/F11/19
AUTO EDIT SET UP/F5/108, 111Preview audio signal selection AUTO EDIT SET UP/F3/108Preview video signal selection AUTO EDIT SET UP/F2/108React time (operation delay compensation time) setting AUTO EDIT SET UP/F7/108Timing selection MANUAL EDIT SET UP/F1/91
AUTO EDIT SET UP/F1/108VTR (player) to be operated selection AUTO EDIT/F5/99VTR (player/recorder) to be operated selection AUTO EDIT/F6/99
EJECT button LED lighting condition selection OPERATION ENGINEER SET UP/F1/137ENV/recording envelope display MANUAL EDIT SET UP/—/94Error rate: Level display switching RF TEST/F2/141
SERVO TEST/F5/149Measurement time selection RF TEST/F1/141
[F]Fade: During automatic editing AUTO EDIT SET UP/F12, F13/109
During manual editing MANUAL EDIT SET UP/F12, F13/92, 97During playback AUDIO OUT SET UP/F4/63, 65
FF/REW maximum speed setting INTERFACE SET UP/F5/113Field playback/frame playback switching HOME SET UP/F2/18Files: Call USER SET UP/F1/125, 128
Copy USER SET UP/—/129Delete USER SET UP/F3/125, 128File call at power-on USER SET UP/F5/125, 128Lock USER SET UP/F9/125, 127Password USER SET UP/F10/125, 126Save USER SET UP/F2/125, 126Update USER SET UP/—/127
Flash freeze screen output HOME/F2/14
[H]Head cleaning RF TEST/F13/141
– 198 –
INDEX
[ I ] Menu/function keys/pages
IC card TEST/F13/143, 155–162Input signal selection VIDEO IN/F1, F13/23Insert editing: Automatic editing AUTO EDIT/F9, F12/99
Editing channel selection (during automatic editing) INSERT AUTO EDIT CH SELECT/F1–F7,
F9–F12/106Editing channel selection
(during manual editing) INSERT MANUAL EDIT CH SELECT/F1–F7,F9–F12/90
Manual editing MANUAL EDIT/F9, F12/87Internal signal generator signal selection VIDEO IN/F2, F12/23
[J]JOG/VAR mode audio digital processing AUDIO OUT SET UP/F3/63Jog/variable field playback/frame playback HOME SET UP/F2/18
[K]Key touch tone selection PANEL SET UP/F1/119
[L]Last edit (all data input last) call AUTO EDIT/F2/99, 102Last EX (edit data input last) call AUTO EDIT/F1/99, 102Level meter peak hold: Audio input AUDIO IN SET UP/F6/54
Audio output AUDIO OUT SET UP/F6/63Level meter scale switching: Audio input AUDIO IN SET UP/F6/54
Audio output AUDIO OUT SET UP/F6/63Loading: Cassette size selection MECHA TEST/F3/151
Loading operation test without use of tape MECHA TEST/F1/151Local mode: Audio level adjustment PANEL SET UP (OP MAP LOCAL) /F2/124
Key operation selection PANEL SET UP (OP MAP LOCAL) /F5/124Monitor adjustment PANEL SET UP (OP MAP LOCAL) /F4/124Tracking adjustment PANEL SET UP (OP MAP LOCAL) /F3/124Video level adjustment PANEL SET UP (OP MAP LOCAL) /F1/124
[M]Manual editing MANUAL EDIT/F12/87Menu screen transition tables —/—/4–6Mode connector correlation table INTERFACE SET UP/—/115Monitor connector: Switching mixed signals to be output AUDIO OUT MONITOR/F11–F12/61
Volume adjustment of audio signals to be output AUDIO OUT MONITOR/F7/61
– 199 –
INDEX
[O] Menu/function keys/pages
OP MAP setting method: Local PANEL SET UP (LOCAL) /—/124Remote PANEL SET UP (REMOTE) /—/121, 122
Operation messages —/—/176, 177Operation time display TEST/—/138Output signal (TAPE/EE) switching HOME/F1/14
[P]PB fade ON/OFF AUDIO OUT SET UP/F4/63, 65PB level adjustment VIDEO OUT HD/F2/25
VIDEO OUT SD/F2/31PB OUT (output audio characteristics at playback start) AUDIO OUT SET UP/F5/63Peak hold: Audio input value AUDIO IN SET UP/F6/54
Audio output value AUDIO OUT SET UP/F6/63Player 1/player 2 selection AUTO EDIT/F5/99Player sync AUTO EDIT SET UP/F4/108Player/recorder selection AUTO EDIT/F6/99PR level adjustment VIDEO OUT HD/F3/25
VIDEO OUT SD/F3/31Preroll time selection HOME SET UP/F11/19
AUTO EDIT SET UP/F5/108, 110MULTI CUE SET UP/F13/86
Preview audio signal selection AUTO EDIT SET UP/F3/108Preview video signal selection AUTO EDIT SET UP/F2/108Programmed play function setting HOME SET UP/F3–F4/18, 21
[R]React time (operation delay compensation time) setting AUTO EDIT SET UP/F7/108REC INHIBIT selection: During editing MANUAL EDIT SET UP/—/93, 94
During recording HOME/F13/15Recording inhibit mode selection HOME/F13/15Reference selection —/—/20Remote mode: Audio level adjustment PANEL SET UP (OP MAP REMOTE) /F2/121
Eject key operation enable PANEL SET UP (OP MAP REMOTE) /F7/121Key operation selection PANEL SET UP (OP MAP REMOTE) /F5/121Monitor adjustment PANEL SET UP (OP MAP REMOTE) /F4/121Operation of all functions enable/disable PANEL SET UP (OP MAP REMOTE) /F6/121Tracking adjustment PANEL SET UP (OP MAP REMOTE) /F3/121Video level adjustment PANEL SET UP (OP MAP REMOTE) /F1/121
Remote: 50P parallel ON/OFF INTERFACE SET UP/F3/113RS-232C parameter setting INTERFACE SET UP/F2/113, 116RS-422A P2 bus selection INTERFACE SET UP/F1/113, 115RS-422A-connected VTR ON/OFF AUTO EDIT/F3/99
RF adjusted value display RF TEST/F11–F12/141, 143
– 200 –
INDEX
[S] Menu/function keys/pages
Search dial: Jog speed selection, maximum PANEL SET UP/F3/119Shuttle clutch point setting PANEL SET UP/F4–F5/119Shuttle maximum speed selection PANEL SET UP/F6/119Variable clutch point setting MULTI CUE SET UP/F9/86
PANEL SET UP/F13/119Variable speed selection, maximum MULTI CUE SET UP/F10/86
PANEL SET UP/F12/119Sensor operation check MECHA TEST/F5/145Software version display TEST/—/139Split editing AUTO EDIT/F10/99Standby mode duration selection HOME SET UP/F13/19Standby OFF mode: Output signal switching AUDIO OUT SET UP STATE/66, 67
VIDEO OUT SET UP STATE/28, 29Tape mode setting HOME SET UP/F6/18
Still mode duration selection HOME SET UP/F12/19Superimposing: Character selection TC/CHR/F13/72
Error messages ON/OFF TC/CHR/F12/72, 74Position changes TC/CHR/—/73
Sync play ON/OFF HOME SET UP/F1/18System error messages —/—/174, 175
[T]Tape position indicator AUTO EDIT/—/100Test front: Key check TEST FRONT/F2/151, 153, 154
Panel TEST FRONT/F1/151, 152Time code: Color frame bit addition TC/CHR/F6/72
Drop/non-drop frame selection TC/CHR/F5/71Initial value setting HOME/—/11Internal/external input selection TC/CHR/F1/71LTC selection TC/CHR SET UP/F13/77Readout mode selection TC/CHR/F10/72REC RUN/FREE RUN selection TC/CHR/F4/71Slave lock mode ON/OFF TC/CHR/F2/71Superimposing ON/OFF TC/CHR/F11/72TC channel ON/OFF INSERT MANUAL EDIT CH SELECT/F7/89TC/UB switching HOME/F5/14Time code value holding HOME/F7/14VITC selection TC/CHR SET UP/F10, F12/77
Time data: Reset HOME/F6/14TC/CTL switching HOME/F4/14
Tracking adjustment MANUAL EDIT SET UP/F10/91, 95, 96AUTO EDIT SET UP/F10/109SERVO TEST/F10/149
– 201 –
INDEX
[U] Menu/function keys/pages
User bit: List of settings TC/CHR/—/75Slave lock mode setting TC/CHR/F2/71User bit value display HOME/F5/14
User files: Automatic file call at power-on USER SET UP/F5/125, 128Call USER SET UP/F1/125, 128Copy USER SET UP/—/129Delete USER SET UP/F3/125, 128Lock USER SET UP/F9/125, 127Password USER SET UP/F10/125, 126Save USER SET UP/F2/125, 126Update USER SET UP/—/127
[V]V/A control parameters INTERFACE SET UP/F4/113, 116Variable memory AUTO EDIT/F4/99, 103, 104Video channel ON/OFF INSERT MANUAL (AUTO) EDIT CH SELECT/F1/
89, 106Video input: Input signal bypass
Signal selection VIDEO IN/F1, F13/23VIDEO OUT SD/F1/31
Video output: Black level adjustment VIDEO OUT HD/F4/25VIDEO OUT SD/F4/31
TAPE/EE switching in each mode AUDIO OUT SET UP STATE/66, 67VIDEO OUT SET UP STATE/—/71, 72
[Y]Y level adjustment VIDEO OUT HD/F1/25
– 202 –
– 203 –
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANYDIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500EASTERN ZONE:One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835Central Region:1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Government Marketing Department:52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Broadcast PARTS INFORMATION & ORDERING:9:00 a.m.–5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Sales CompanyDivision of Matsushita Electric of Puerto Rico Inc.San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
Panasonic Broadcast EuropePanasonic Broadcast Europe Ltd.West Forest Gate, Wellington Road, Wokingham, Berkshire RG40 2AQ U.K. Tel: 0118 902 9200
Panasonic Broadcast Europe GmbHHagenauer Str. 43, 65203 Wiesbaden-Biebrich Deutschland Tel: 49-611-1816-0
Printed in JapanVQT9466-1 F0401H4111 P E
- 2 -
AJ-HD3700H
Operating Instructions (Supplement 2)
Outline of changes and additions This supplement 2 describes what changes and additions have been made to the operating instructions of the AJ-HD3700H digital video cassette recorder. New changes and additions Item concerned Change/addition Page in AJ-HID3700H’s Page in this operating instructions supplement OPERATION F2 (STILL STEP) key added Software section, 2 to 3 ENGINEER SET UP page 137 HOME SET UP F12 (STILL) key added Software section, 4 page 19
OPERATION ENGINEER SET UP menu
- 3 -
OPERATION ENGINEER SET UP menu Key Key designation Description
F1 EJECT LED Enables the lighting conditions of the EJECT button's LED to be selected. MODE 1: The LED lights during the time starting when the VTR is transferred to the eject mode until the cassette is ejected or when cassette unloading is completed. (it lights during the unloading period and in the EJECT mode.) MODE 2: The LED lights during the time starting when the VTR is transferred to the eject mode until the cassette is ejected. (it lights only during the unloading period.) F2 STILL STEP ON: When the stop/still mode holding time is set to 5 min with the F1 2 (STILL) key of the HOME SET UP menu and then this F2 key to ON, still time can be extended to 30 minutes moving the tape back and forth slightly. The tape is moved one frame amount every 2 minutes elapsed, and the tape movement is stopping within about ±2 frames from the beginning point of this mode. The VTR is transferred to the tape tension release (loosing) mode in order to prevent the tape damage after 30 minutes has elapsed. Note that the CUE audio is output while the STILL STEP mode is activated. This function does not work other than 5 min in the F1 2 (STILL) key setting of the HOME SET UP menu. OFF: STILL STEP does not function. When the stop/still mode holding time has elapsed, the VTR is transferred to the tape tension release (loosing) mode. F3-F7 - F8 EXIT Returns the VTR to the ENGINEER SET UP menu screen. F9-Fl 1 - F12 ACCEL Selects how far to accelerate the reel at a speed under multiple speed selected by F1 3 (KNEE) during a FF or REW operation (in the SHTL mode). MAX: Maximum acceleration is applied at all times. MIDDLE: Medium acceleration as far as the knee is applied. (This is the default value.) MIN: The acceleration as far as the knee is reduced. *When the MAX setting is selected, there is no knee due to the maximum acceleration. *There is no knee when an L-size cassette is used. F13 KNEE Selects the multiple of the normal speed at which the reel speed is to be transferred from the acceleration selected by F12 (ACCEL) to maximum acceleration during a FF or REW operation (in the SHTL mode). X8: 8xnormal speed X15: 15xnormal speed X20: 20xnormal speed X30: 30xnormal speed
- 4 -
HOME SET UP menu Key Key designation Description F9-F10 F11 PREROLL After pressing the F1 1 key, turn the ADJUST control. For selecting the preroll Selection can be made between 0 and 30 seconds. time. F12 STILL Sets the stop/still (still picture) mode holding time. For setting the In order to protect the tape, the VTR is automatically transferred STOP/STILL (static frame) to the tape tension release mode (loosing) after a specific time mode holding time. has elapsed. This specific time can be set. After pressing the F1 2 key, turn the ADJUST control. 1 sec, 3 see, 30 sec, 1 min, 3 min or 5 min can be set as the holding time. When the stop/still mode holding time is set to 5 min, the STILL STEP ON/OFF function can be selected. For details, refer to F2 (STILL STEP) key of the OPERATION ENGINEER SET UP menu on page 3. F13 STBY OFF For setting the time for the transfer from tape loosing to standby For setting the time for the OFF. transfer to standbay OFF. After pressing the F1 3 key, turn the ADJUST control. 1 sec, 3 sec, 30 sec, 1 min, 3 min, 16 min and - [infinity: No transfer to standby OFF mode (drum stop/half loading)] can be set.