ribbon cable interconnect solutions - farnell element14 · 2012. 4. 20. · pages 10 and 11 ultra...

Tyco Electronics CorporationHarrisburg, PA

TE (logo) and Tyco Electronics are trademarks of the Tyco Electronics group of companies and its licen-sors.

tycoelectronics.com

82012–2.5M–CIS–FP–10-09

Ribbon Cable Interconnect Solutions

Cata

log

820

12 R

evise

d 10

-09

Rib

bo

n C

ab

le In

terc

on

nect S

olu

tion

s

2Catalog 82012 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000Revised 10-09 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208

Ribbon Cable Connector Selection Guide


Male-on-Wire215083 Series,

Page 38

Mates to .50" x .50"Micro-MaTch

Female Top Entry,215079 Series,PCB Connector

Page 34

.050" [1.27 mm]Cable Pitch


Page 38


Female Side Entry,215460 Series,PCB Connector

Page 35


Page 38


Female Top EntrySMD, 188275 Series,

PCB ConnectorPage 36

50/50 GridReceptacle

Connector with orwithout latch

50/50 GridReceptacleConnectors

without latch

Mates to .050" x .050"Right-Angle

Headers

Mates to .050" x .050"Vertical Headers

Paddle BoardConnector,

215570 Series,Page 39

Solders directly to2.54mm x 1.27mmStaggered 2 rowPCB Footprint


(Continued)

System 50ReceptaclesPages 8-11

Mates to .050" x .100"2-Row Pin Header

GridPages 10 and 11

Ultra ATA BusCompliant Receptacles

Pages 13-15

Mates to .100" x .100"2-Row Pin Header

GridPage 15

Solders to.075" x .100"

4-Row PCB Layout


Mates to .078" [2 mm]x .078" [2 mm]

2-Row Pin HeaderGrid

See 5176264, 5178751 Seriesand Part Number 1775109

(Not in this Catalog)


2 mmReceptacleConnectors

Pages 16 and 17

System 50Paddleboard

Page 12

RibbonCa

bleCo

nnectorSe

lectionGuide

http://www.tycoelectronics.com



PageHead_12_HelvCdBd (Continued)


Ribbon

CableConnector

SelectionGuide

Ribbon Cable Connector Selection Guide (Continued)

Universal I/OPin ConnectorsPages 45 and 46

Mates to .100" x .100"Novo Type FemaleSocket Connector

Pages 48-51

EUROLATCHReceptacles

Page 47

Mates to .100" x .100"3-Row Eurocard

Type C & RSee Catalog 82721

AMP-LATCH NovoConnectorsPages 48-51

622 and 636Series Female

Socket ConnectorsPages 52 and 53

Mates to .100" x .100"2-Row Universal or

Low-Profile HeadersPages 75-96

609 SeriesFemale

Socket ConnectorsPages 54 and 55


(Continued)

.100" x .300"Footprint


Mates to2-Row DIP Socketsor Solders to PCB


622 and636 SeriesDIP PlugsPage 57

609 SeriesDIP PlugsPage 56

Tyco ElectronicsDIP PlugsPage 58



SolderTransition

ConnectorsPage 61

Solders to.050" x .100"

4-Row PCB Footprint


(Continued)




Introduction


DisclaimerWhile Tyco Electronics Corporationand its affiliates referenced herein(“Tyco Electronics”) have made everyreasonable effort to ensure the accuracyof the information in this catalog,Tyco Electronics does not guarantee thatit is error-free, nor does Tyco Electronicsmake any other representation, warrantyor guarantee that the information isaccurate, correct, reliable or current.Tyco Electronics reserves the right tomake any adjustments to the informationcontained herein at any time withoutnotice. Tyco Electronics expressly dis-claims all implied warranties regardingthe information contained herein, includ-ing, but not limited to, any implied war-ranties of merchantability or fitness fora particular purpose. Tyco Electronics’only obligations are those in theTyco Electronics Standard Terms andConditions of Sale, and in no case willTyco Electronics be responsible for anyincidental, indirect, or consequentialdamages arising from the sale, resale,use, or misuse of its products. Usersshould independently evaluate thesuitability of, and test each product for,their application.The dimensions, specifications, designs,construction, materials and processes inthis catalog are for reference purposesonly and are subject to change withoutnotice. Please consult Tyco Electronicsfor the most current product information.The export of certain Tyco Electronicsproducts is restricted by the ArmsExport Control Act (Title 22, U.S.C.Sec 2751, et seq.) or the ExportAdministration Act of 1979, as amended(Title 50, U.S.C., App. 2401 et seq.).Orders may be subject to export approvalby the U.S. Government. Buyer mustcomply with all applicable export lawsof all applicable jurisdictions.© 2009, 1999, 1998, 1996, 1995, 1993,1992, 1989, 1988, 1986, 1985, 1983,1982, 1977, 1976, 1974 and 1973Tyco Electronics Corporation.All Rights Reserved.AMP, AMPLIMITE, AMPMODU, ACTIONPIN, AMP-LATCH, MICRO-MATCH,CHAMP, EUROLATCH, TE LOGO andTYCO ELECTRONICS are trademarks ofthe Tyco Electronics group of companiesand its licensors..Other products, logos, and companynames mentioned herein may betrademarks of their respective owners.

See inside back cover for GlobalContacts and phone numbers.

Restriction on the use of Hazardous Substances(RoHS)At Tyco Electronics, we’re ready to support your RoHS require-ments. We’ve assessed more than 1.5 million enditems/components for RoHS compliance, and issued new partnumbers where any change was required to eliminate therestricted materials. Part numbers in this catalog are identifiedas:RoHS Compliant — Part numbers in this catalog are RoHSCompliant, unless marked otherwise. These products complywith European Union Directive 2002/95/EC as amended 1January 2006 that restricts the use of lead, mercury, cadmium,hexavalent chromium, PBB, and PBDE in certain electrical andelectronic products sold into the EU as of 1 July 2006.NOTE: For purposes of this Catalog, included within the defini-tion of RoHS Compliant are products that are clearly “Out ofScope” of the RoHS Directive such as hand tools and othernon-electrical accessories.NOTE: Information regarding RoHS compliance is providedbased on reasonable inquiry of our suppliers and representsour current actual knowledge based on the information providedby our suppliers. This information is subject to change. For lat-est compliance status, refer to our website referenced at right.

Getting the Information You NeedOur comprehensive on-line RoHS Customer Support Centerprovides a forum to answer your questions and support yourRoHS needs. A RoHS FAQ (Frequently Asked Questions) isavailable with links to more detailed information. You can alsosubmit RoHS questions and receive a response within 24hours during a normal work week. The Support Center alsoprovides:� Cross-Reference from

Non-compliant to Compliant Products� Ability to browse RoHS

Compliant Products in ouron-line catalog

� Downloadable Technical DataCustomer InformationPresentation

� More detailed informationregarding the definitionsused above

� So whatever your questions when it comes to RoHS, we’vegot the answers at www.tycoelectronics.com/leadfree

RoHSCustomerSupportCenter

http://www.tycoelectronics.com/leadfreehttp://www.tycoelectronics.com



Introduction (Continued)


Mass termination capabili-ties of the ribbon cableconnectors have helpedmake ribbon cable, andparticularly .050 [0.127]centerline cable, popularwithin the electronics indus-try. The ability to terminateup to 64 conductors simul-taneously, without strippingor otherwise pre-paring thecable, presents obviouslabor savings.

Ribbon Cable Connectorsare wire-to-board devicesused to make the transitionbetween cable and pcboard circuitry. They findheavy use within equipmentto connect one board toanother or one subsystemto another. The connectorsare also used ininput/output applications,connecting different piecesof equipment.

Ribbon Cable Solutions areavailable on three separatecable centerline spacings.They include:

.025 [0.64] Centerlines� System 50 receptacles� System 50 paddleboards� Pin headers

.039 [1.00] Centerlines� 2.0 mm receptacles� Breakaway pin headers

.050 [1.27] Centerlines� 50/50 Grid connectors� Micro-MaTch connectors� AMP-LATCH novo recep-tacle connectors

� DIP plugs� EUROLATCH receptacleconnectors per DIN41612 and IEC 603-2

� Pin Headers

System 50 ribbon cablereceptacles will terminatecable on .025 [0.64] center-lines. They are available inselect sizes from 20 thru100-positions, and acceptwire size range 30 AWG[0.05 mm2] solid orstranded wire and 32 AWG[0.03 mm2] stranded pvcinsulated wire. Housing andcover are made of hightemperature tolerant ther-moplastic material, black,UL 94V-0 rated. A singlemating beam, phosphorbronze contact provides theinterconnect between theconductor and the .0152[0.382] posts on .050 x .100

[1.27 x 2.54] grid. Alsoavailable in paddleboardconfigurations.

2.0 mm [.079] ribboncable receptacles featurecontacts on a true 2.0 mm[.079 in.] mating grid for1.0 mm [.039 in.] pitchribbon cable. Selectconfigurations are availablebetween 8 and 50-positions.Receptacles featureinsulation displacementcontacts (IDC).

50/50 Grid connectorsAlthough AMPMODU 50/50grid vertical headers andReceptacles are designedfor parallel board-to-boardstacking in high densityapplications, Right-angleboard-to-board and cable-to-board applications arealso possible since thevertical receptacles alsomate with non-latchingright-angle headers and thevertical headers also matewith non-latching cableconnectors.

Micro-Match connectorsMiniaturization and the trendtowards higher density ofelectronic functions on asubstrate led to the intro-duction of the Micro-MaTchconnector. The systemoffers a range of board andwire connectors, enabling avariety of wire-to-board andboard-to-board interconnec-tions. Its design prevents

the traditional failure modein tin-plated connections,fretting corrosion. An addi-tional positioning spring inthe female part absorbs rel-ative movements caused byvibrations and thermalexpansion between maleand female contacts. Bypreventing movements onthe contact spot, a gas tightconnection can be guaran-teed under allcircumstances.

AMP-LATCH novo recep-tacles feature two rows ofcontacts on .100 x .100[2.54 x 2.54] centers onselected sizesof 10 thru 64-positionsand mate with .025 [0.64]square or round posts. TheAMP-LATCH novo tuning-fork contact offers a mili-tary-approved design, at anaffordable cost. Polarizationoptions include military,center and military, or dualbar.

DIP (Dual In-Line Package)plugs provide a permanentconnection of ribbon cableto a pc board or matingto DIP sockets. Using thesame centerline dimensionsas DIP integrated circuits,DIP plugs offer spaceefficiency and a low profileof .253 [6.43].

Need more information?

Call Technical Support atthe numbers listed below.

Technical Support is staffedwith specialists well versedin all Tyco Electronicsproducts. They can provideyou with:� Technical Support� Catalogs� Technical Documents� Product Samples� Tyco ElectronicsAuthorized DistributorLocations




Table of Contents


Ribbon Cable Connector Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3.025 [0.64] Centerline Ribbon Cable ConnectorsSystem 50 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12Cable-to-Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9, 12Board-to-Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11

Ultra ATA compliant Bus Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15

.039 [1.00] Centerline Ribbon Cable Connectors2 mm [.079] Receptacle Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17

AMPMODU 50/50 Grid Connector SystemIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Board-to-Board Vertical Receptacles and Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Board-to-Board Vertical Receptacles, Double Row, .050 x .050[1.27 x 1.27] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Board-to-Board Vertical Headers, Double Row, .050 x .050 [1.27 x 1.27] Centers . . 21Recommended PC Board Layouts for Vertical Connectors . . . . . . . . . . . . . . . . . . . . 22

Board-to-Board Right-Angle Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Board-to-Board Right-Angle Headers, Double Row, .050 x .050 [1.27 x 1.27]Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cable-to-Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Cable-to-Board Receptacle Connectors, Double Row, .050 x .050 [1.27 x 1.27]Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Terminating Covers for Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Application Tooling for Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Technical Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Micro-MaTch Connector SystemMiniature Connector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30System Overview/Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Applications (3 Dimensions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Applications (2 Dimensions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Female-on-Board Connector, Top Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Female-on-Board Connector, Side Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Female-on-Board Connector Surface Mount Device (SMD) . . . . . . . . . . . . . . . . . . . . . 36Male-on-Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Male-on-Wire Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Paddle Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Crimp On Snap In (COSI) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Specials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Application Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 43Lead Assembly and Sample Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

.050 [1.27] Centerline Ribbon Cable ConnectorsUniversal I/O Pin Connectors without Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Universal I/O Pin Connectors with Slotted Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . 46EUROLATCH Receptacles 64-Position (Three-Row Housings, Two Rows Loaded) . . . 47AMP-LATCH Novo Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-51Military Polarized, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . . . . . . . . . . 49Center and Military Polarized, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . 50Dual Polarized, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 622 and 636 Series . . 52, 53Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 609 Series . . . . . . . . . 54, 55DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 609 Series . . . . . . . . . . . . . . . . . . . . . . . 56DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 622 Series . . . . . . . . . . . . . . . . . . . . . . . 57





Table of Contents (Continued)

.050 [1.27] Centerline Ribbon Cable Connectors (Continued)DIP Plugs, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58DIP Plugs, .100 x .300 [2.54 x 7.62] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59DIP Plugs, .100 x .600 [2.54 x 15.24] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604-Row PCB Solder Transition Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611-Row Horizontal Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

AccessoriesFlexible Pull Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Universal I/O Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Military Polarizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Keying Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Strain Relief for 622 Series DIP Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Pull Loops, Permanent (For Receptacles and Pin Connectors) . . . . . . . . . . . . . . . . . . . 66Strain Relief for Universal I/O without Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Strain Relief for 609 Series (Tulip Contact) Female Socket Connectors . . . . . . . . . . . . 67Strain Relief for AMP-LATCH Novo and Ultra ATA compliant Bus Connectors . . . . . . . 68Strain Relief for 2 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Strain Relief for 622 and 636 Series Female Socket Connectors . . . . . . . . . . . . . . . . . 69

Application Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-74Low Profile Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-83Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54]Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76, 77

Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54]Centerlines and “Kinked” Solder Tails for PCB Retention . . . . . . . . . . . . . . . . . . . 78, 79

IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches,Military and Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . 80, 81

IDC Low Profile Ejection Style Pin Headers, Center Polarized, .100 x .100[2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82, 83

Universal Ejection Style Pin Headers and Pinless HeadersUniversal Ejection Style Pin Headers, Military, Center and Dual Polarized,.100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84-86

Universal Ejection Style Pin Headers, ACTION PIN Contacts, Military,Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . 87, 88

Universal Ejection Style Pin Headers, Military, Center and Dual Polarized,.100 x .100 [2.54 x 2.54] Centerlines, Right-Angle . . . . . . . . . . . . . . . . . . . . . . . . 89-91

Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized,.100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92, 93

Universal Ejection Style Pin Headers, with PCT Housing, .100 x .100[2.54 x 2.54] Centerlines, .025 [0.64] Sq. Posts (Mating End) . . . . . . . . . . . . . . . 94, 95

Latches for Ejection Style Universal Pin Headers and Pinless Headers . . . . . . . . . . . . 96

Cable Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97, 98Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99





.025

[0.64]Ce

nterlin

eRibbonCa

bleCo

nnectors

System

50Ca

ble-to-Board

Connectors

System 50 Cable-to-Board Connectors, .025 [0.64] Centerline Ribbon Cable

The System 50 RibbonCable connector is areceptacle connector thatwill terminate ribbon cableon .025 [0.64] centerlines.It is available in select sizesfrom 10 to 100 positionsand will accommodate 30AWG [0.05 mm2] solid orstranded and 32 AWG[0.03 mm2] stranded

conductors with PVC cableinsulation.

The housing and coverare of a high temperaturetolerant thermoplastic(black) with a UL 94V-0rating. A phosphor bronzesingle mating beam contactprovides the interconnectbetween the conductor andthe .015 [0.38] square

posts on the .050 x .100[1.27 x 2.54] grid. Thecontacts are plated with30 gold duplex plating. Thelatching feature is locatedon the receptacle, not theheader, and saves boardspace and eliminates futureproblems of “latch heightcompatibility.”

Product Facts� Preassembled housing and

cover

� One-step termination

� End and daisy chaintermination

� Positive end latching ofconnector to universalheader

� Terminates 30 AWG[0.05 mm2] solid orstranded and 32 AWG[0.03 mm2] stranded.025 [0.64] centerlineribbon cable with PVCinsulation

� Connectors are RoHScompliant

� Recognized under theComponent Programof the UnderwritersLaboratories, Inc.UL File No. E28476

� Certified by theCanadian StandardsAssociation,File No. LR 7189

R

R





.025[0.64]Centerline

Ribbon

CableConnectors

System50

Cable-to-BoardConnectors

System 50 Cable-to-Board Connectors,.025 [0.64] Centerline Ribbon Cable (Continued)

Double Row Receptacle

Material and FinishHousing — Black thermoplastic,UL 94V-0 ratedLatches — Stainless steelContacts — Phosphor bronze, plated30 microinch gold over nickel with tinin termination area

Related Product DataMateable Connectors —See Tyco Electronics Catalog 82178See Part Numbers 104068 and 104069Series on pages 10 and 11Mates with Posts — .015 [0.38]square, .125 [3.18] long, on.050 x .100 [1.27 x 2.54] grid

Technical DocumentsProduct Specification108-1109Application Specification114-25029

No. of DimensionsPos. A B C D E F

Part Number

.510 .445 .225 .200 .096 .29410 12.95 11.30 5.72 5.08 2.44 7.47 2-111196-5

.610 .545 .325 .300 .146 .39414 15.49 13.84 8.26 7.62 3.71 10.01 2-111196-6

.660 .595 .375 .350 .171 .44416 16.76 15.11 9.52 8.89 4.34 11.28 2-111196-7

.760 .695 .475 .450 .221 .54420 19.30 17.65 12.07 11.43 5.61 13.82 1-111196-8

.860 .795 .575 .550 .271 .64424 20.32 20.19 14.61 13.97 6.88 16.36 2-111196-8

.910 .845 .625 .600 .296 .69426 23.11 21.46 15.88 15.24 7.52 17.63 2-111196-9

1.010 .945 .725 .700 .346 .79430 25.65 24.00 18.42 17.78 8.79 20.17 1-111196-9

1.110 1.045 .825 .800 .396 .89434 28.19 26.54 20.96 20.32 10.06 22.71 3-111196-0

1.260 1.195 .975 .950 .471 1.04440 32.00 30.35 34.54 24.13 11.96 26.52 2-111196-0

1.360 1.295 1.075 1.050 .521 1.14444 34.54 32.89 27.31 26.67 13.23 29.06 3-111196-1

1.510 1.445 1.225 1.200 .596 1.29450 38.35 36.70 31.12 30.48 15.14 32.87 2-111196-1

1.760 1.695 1.475 1.450 .721 1.54460 44.70 43.05 37.47 36.83 18.31 39.22 2-111196-2

1.860 1.795 1.575 1.550 .771 1.64464 47.24 45.59 40.00 39.37 19.58 41.76 3-111196-2

1.960 1.895 1.675 1.650 .821 1.74468 49.78 48.13 42.55 41.91 20.85 44.30 3-111196-4

2.060 1.995 1.775 1.750 .871 1.84472 52.32 50.67 45.08 44.45 22.12 46.84 2-111196-3

2.260 2.195 1.975 1.950 .971 2.04480 57.40 55.75 50.17 49.53 24.66 51.92 3-111196-3

2.760 2.695 2.475 2.450 1.221 2.544100 70.10 68.45 62.87 62.23 31.01 64.62 2-111196-4

See Application Specification for termination tooling.Note: All part numbers are RoHS compliant.

.254[6.45]

.228[5.79]

.054[1.37]

.430[10.92]

.102[2.59]

.228[5.80]

.335[8.51]

.246[6.25]

.580[14.73]Before

Termination

.198[5.03]

.100[2.54]

.100[2.54] .050

[1.27]

F

E

D

ACover

Latch

Contact

Housing

Typ.

Position #1Indicator

C

B





.025

[0.64]Ce

nterlin

eRibbonCa

bleCo

nnectors

System

50Bo

ard-to-Board

Connectors

System 50 Board-to-Board Connectors, Through-Hole Headers

Shrouded,Double RowVertical

Material and FinishHousing — Black thermoplastic,UL 94V-0 ratedContacts — Copper alloy, plated.000030 [0.00076] gold in mating area,.000150 [0.00381] tin on solder posts,with entire contact underplated .000050[0.00127] nickel

Related Product DataMateable Receptacles — page 9


No. of Dim. PartPositions A Number

.38010 9.65 5-104068-2

.43012 10.92 5-104068-8

.48014 12.19 5-104068-9

.53016 13.46 6-104068-0

.63020 16.00 5-104068-1

.73024 18.54 6-104068-1

.78026 19.81 6-104068-2

.88030 22.35 5-104068-3


.98034 24.89 6-104068-3

1.13040 28.70 5-104068-4

1.23044 31.24 6-104068-4

1.38050 35.05 5-104068-5

1.63060 41.40 5-104068-6

1.83068 46.48 6-104068-8

1.93072 49.02 6-104068-5

2.13080 54.10 6-104068-6

2.630100 66.80 6-104068-7**Point of measurement for gold thickness.**Circuit identification feature omitted on 8, 10, 12 and 14position headers.

Note: All part numbers are RoHS compliant.

.284[7.21]

.100[2.54]

.100[2.54]

.092[2.34]

.390[9.91]

A

.015[0.38]

.344[8.74]

.060[1.52]2 Plc.

.055*[1.40]

.050[1.27] Typ.

Circuit IdentificationFeature**






Ribbon

CableConnectors

System50

Board-to-BoardConnectors

System 50 Board-to-Board Connectors, Through-Hole Headers (Continued)

Shrouded,Double RowRight-Angle

Material and FinishHousing — Black thermoplastic,UL 94V-0 ratedContacts — Copper alloy, plated.000030 [0.00076] gold in mating area,.000150 [0.00381] tin on solder posts,with entire contact underplated .000050[0.00127] nickel

Related Product DataMateable Receptacles — page 9


Circuit IdentificationFeature**

.540[13.72]

.100[2.54]

.350[8.89]

.290[7.37]

.050[1.27]

Typ.

Note 2

Note 1

.060[1.52]2 Plc.

A

.055*[1.40]

.100[2.54]

.160 [4.06]at Post Tips

.100[2.54]at PostTips

.408[10.36]

Hold downpost


.3308 8.38 5-104069-8

.38010 9.65 5-104069-4

.63020 16.00 5-104069-1

.73024 18.54 6-104069-2

.78026 19.81 6-104069-3

.88030 22.35 5-104069-5

.98034 24.89 6-104069-4


1.13040 28.70 5-104069-6

1.38050 35.05 5-104069-2

1.63060 41.40 5-104069-7

1.83068 46.80 6-104069-8

1.93072 49.02 6-104069-6

2.13080 54.10 5-104069-3

2.630100 66.80 6-104069-7

**Point of measurement for gold thickness.**Circuit identification feature omitted on 8, 10, 12 and14 position headers.

Notes: 1. Hold down posts located as shown for16 through 100 position headers.

Notes: 2. Hold down posts located as shown for8 through 14 and 60 through 100 positionheaders.

Notes: 3. All part numbers are RoHS compliant.





.025

[0.64]Ce

nterlin

eRibbonCa

bleCo

nnectors

System

50Ca

ble-to-Board

Connectors

System 50 Cable-to-Board Connectors, .025 [0.64] Centerline Ribbon Cable

Paddleboard

Material and FinishHousing — LCP thermoplastic,UL 94V-0 rated, blackCover — Polyester, UL 94V-0 rated,blackContacts — Phosphor bronze, plated.000100 [0.00245] min. tin over .000050[0.00127] min. nickel underplating


.024[0.61]

.118[3.00]

.040[1.02] .030

[0.76]Standoffs

(Various Locations)

B

.100[2.54]

A

.020[0.51]

.045[1.19]Ref.

.050[1.27]

No. of PCB Dimensions PartPos. Layout A B Number

.436 .20010 1 11.07 5.08 5111595-1

.536 .30014 1 13.61 7.62 5111595-2

.586 .35016 2 14.88 8.89 5111595-3

.686 .45020 2 17.42 11.43 5111595-4

.786 .55024 2 19.96 13.97 5111595-5

.836 .60026 1 21.23 15.24 5111595-6

.886 .65028 2 22.50 16.51 2-5111595-0

.936 .70030 1 23.77 17.78 5111595-7

1.036 .80034 1 26.31 20.32 5111595-8

1.186 .95040 2 30.12 24.13 5111595-9

Typ..050[1.27]

Typ.

.168[4.27]

.075[1.91]

Typ.

.304[7.72]

.008[0.20]Typ.

.340[8.64]

(Unterminated)Position 1Indicator

.273[6.93]

(Terminated)

.050[1.27]

Typ.

.075[1.91]

Typ.

.304[7.72]

.031[0.79]

Typ.

Printed Circuit Board Hole Layout #1

No. of PCB Dimensions PartPos. Layout A B Number

1.286 1.05044 2 32.66 26.67 1-5111595-0

1.336 1.10046 1 33.93 27.94 1-5111595-7

1.436 1.20050 1 36.47 30.48 1-5111595-1

1.686 1.45060 2 42.82 36.83 1-5111595-2

1.786 1.55064 2 45.36 39.37 1-5111595-3

1.886 1.65068 2 47.90 41.91 1-5111595-9

1.986 1.75072 2 50.44 44.45 1-5111595-4

2.186 1.95080 2 55.52 40.53 1-5111595-5

2.686 2.450100 2 68.22 62.23 1-5111595-6

See Application Specification for termination tooling.Note: All part numbers are RoHS compliant.

B.050[1.27]

Typ.

.075[1.91]

Typ.

.304[7.72]

.031[0.79]

Typ.

Printed Circuit Board Hole Layout #2

B






Ribbon

CableConnectors

Ultra

ATACom

pliantBusConnectors

Ultra ATA Compliant Bus Connectors, .025 [0.64] Centerline Ribbon Cable

Product Facts� IDC termination

� Backward compatible withcurrent IDE Interfaces

� Improved signal integrity:1 to 1 signal to ground ratio

� Improved crosstalk whencompared to existing IDECable Assembly

� Color coded connectorsfor “System board,” and“Master HDD” and“Slave HDD”

� Cable impedance 80 ohms

� Up to 3 connectors per cableassembly

� 15 microinches gold plating



� Terminates 30 AWG solid orstranded PVC insulated 80conductor ribbon cable

R

R

Ultra ATA is the next gener-ation IDE (Integrated DriveElectronics) bus. The currentIDE bus has a maximumdata transfer rate of about16.5 MB/second. As thebus speeds and disk driveperformances increase, thecable assembly betweenthe motherboard and harddrive becomes a limitingfactor in data transfer fromthe drive.

The Ultra ATA compliantconnector and cableassembly fromTyco Electronics providethe customer with improvedelectrical performance bycreating a 1:1 signal-to-ground ratio. The connectordesign incorporates an IDCbus bar to common the 40additional ground signals.The cable is .025" center-line PVC ribbon cable. Theconnector is fully backwardcompatible with existing 40-position headers with pin20 removed on mother-

boards and disk drives.

The new connectors arecolor coded to identify:

1. system board connector2. primary or master hard

drive connector3. slave drive connector

Standard Issues

The Ultra ATA compliantcable performance specifi-cation is part of the SmallForm Factor Committee No.8049.

Contacts Available:

� 80 position IDC contactterminations

� 40 signal contacts� 40 ground terminations tospecial IDC bus bar





.025

[0.64]Ce

nterlin

eRibbonCa

bleCo

nnectors

UltraATACo

mpliant

BusCo

nnectors

Ultra ATA Compliant Bus Connectors, .025 [0.64] Centerline Ribbon Cable

GroundBus Bar

Max.

SignalContacts

ContactOptional Center*Polarizer Bar

Position 1 Position 1 Position 1

Cover

OddGnd

Housing

Pos. No. 1Indicator

.420[10.67]

.492[12.50]

Ref..610[15.49]

.240[6.10]

2.186[55.52]

1.90[48.26]

.100[2.54]

.100[2.54]

“System” BoardConnector

“Slave”Connector

“Master” or“Primary”Connector

Configuration A

“System” BoardConnector

“Slave”Connector

“Master” or“Primary”Connector

Configuration B

Terminated View

Color CodedConductor No. 1

Pin 34Conductor Cutper SFF-8049

Related Product DataStrain Relief — Part Number499252-1Mateable Headers — page 15

Material & FinishHousing and Cover —Thermoplastic, UL 94 V-0 rated, colorper tableContacts — Phosphor bronze, platedgold per table on mating end, .000050[0.00127]min. tin in wire terminationarea, over .000050 [0.00127] min nickelon entire contact.

Technical DocumentsProduct Specification108-1740Application Specification114-40056See Application Specification fortermination tooling.

AccessoriesStrain Relief — page 68Keying Plug — page 64Pull Loops — page 66Pull Tabs — page 63

Circuit 20Molded Shut

*Center & Military Polarized Military PolarizedConnector Type 15µ" Gold Housing Cover 15µ" Gold Housing CoverColor Color Color Color“System” Board 1658619-2 Blue Black 1658618-2 Blue Black

“Primary” or “Master” 1658619-1 Black Black 1658618-1 Black Black“Slave” 1658619-3 Gray Black 1658618-3 Gray Black

Notes: 1. All connectors are “ODD GROUND” configuration, ie. all odd cable conductors are grounded. “EVEN GROUND” connectors are not available.See Customer Drawings for detailed electrical connection descriptions.

2. All part numbers are RoHS compliant.






Ribbon

CableConnectors

Ultra

ATACom

pliantBusConnectors

Ultra ATA Compliant Bus Connectors, .025 [0.64] Centerline Ribbon Cable (Continued)

Universal Headers — Pin 20 OmittedPost Housing Latch Part Contact Finish Solder Tail CommentsType Material Type Number (Plating Code) LengthVertical Nylon or PBT Long 5111824-9 D .1102.79

Vertical Nylon or PBT Short 6489700-1 B .123 PP3.12

Legend: PP — Polarization Peg

Ultra ATACompatible Headers

Low Profile Headers — Pin 20 OmittedPost Housing Latch Part Contact Finish Solder Tail HousingType Material Type Number (Plating Code) Length ColorVertical Nylon None 1888188-1 A .120 Black3.05

Vertical Nylon None 1888188-2 B .120 Black3.05

Vertical Nylon 6T None 2-1734161-4 C .122 Black3.10

Vertical Nylon 6T None 2-1734161-5 C .122 Blue3.10

Vertical Nylon None 1734162-2 C .110 Black2.79

Vertical Nylon None 1734162-4 C .110 Blue2.79

Plating Code A — Duplex plated, gold flash on mating surfaces, .000100 [0.00254] min. tin on solder area, withentire post underplated .000050 [0.00127] min. nickel.Plating Code B — Duplex plated, gold flash over palladium-nickel, .000015 [0.00038] min. total on mating surfaces,.000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015[0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated.000050 [0.00127] min. nickel.Plating Code C — Gold flash over nickel underplate on entire post.Plating Code D — Duplex plated, gold flash over palladium-nickel, .000030 [0.00076] min. total on mating surfaces,.000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015[0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated.000050 [0.00127] min. nickel.






.039

[1.00]Ce

nterlin

eRibbonCa

bleCo

nnectors

.079

[2.00]ReceptacleCo

nnectors

2.0 mm [.079] Receptacle Connectors

Product Facts� True hard metric 2.0 x 2.0

[.079 x .079] mating grid for1.0 [.039] pitch ribbon cable

� Wide selection ofconfigurations, 8-50positions

� Insulation displacement(IDC), beryllium coppercontacts, duplex platedgold-over-nickel

� Top/bottom single beamcontact orientation

� UL 94V-0 rated thermo-plastic components

� Assemblies are furnishedpreassembled withtermination covers

� Optional polarization

� Optional strain reliefavailable

� Connector assembliespackaged for ease ofhandling and protection



Performance DataDurability — 150 cyclesTermination Resistance —25 milliohms max.Mating Force —1.67 N max. per contactUnmating Force —0.14 N min. per contactOperating Temperature —-65°C to +105°C

Technical DocumentsProduct Specification108-1372

Application Specification114-40038

R

R

The 2.0 [.079] receptacleconnector family featurescontacts on a true 2.0 x 2.0[.079 x .079] mating gridfor 1.0 [.039] pitch 28 AWGribbon cable. A variety ofconfigurations are availablefrom 8 through 50 positions.This small, compactconnector is finding wideacceptance throughout theelectronic industry, particu-larly in the smaller laptopand notebook type comput-ers with 63.5 [2.5] drives.Other areas of applicationinclude point-of-sale termi-nals, fax machines, photo-copiers, printers, consumerelectronics, and other com-puter peripheral equipment.

These receptacles featureinsulation displacementcontacts (IDC) with atop/bottom single-beamcontact orientation.Contacts are berylliumcopper, duplex plated0.00076 [.000030] gold

in the mating area and0.00254 [.000100] min.tin on termination end, allover 0.00127 [.000050]nickel underplating.Contact mating area is 1.54[.061] from the face of thehousing and they accept0.50mm [.0197] round orsquare posts.

Housings are made ofUL 94V-0 rated polyesterwith optional center barpolarization. Completeassemblies are furnishedpreassembled with termina-tion covers. The completeassembly presents a com-pact design only 5.2 [.203]wide over the terminationcover by 4 [.157] deep by4 [.157] wide mating end.Terminated height is 8.48[.334]. Optional strain reliefavailable. Assemblies arepackaged for ease ofhandling and protection.

METRICDimensions are






Ribbon

CableConnectors

.079[2.00]R

eceptacleConnectors

2.0 mm [.079] Receptacle Connectors,Non-Polarized and Center Polarized Bar

Material and FinishHousing and Termination Cover —UL 94V-0 rated polyester, blackContacts — Beryllium copper, duplexplated 0.00076 [.000030] min. gold onmating end, 0.00013 [.000005] min.gold on termination end, all underplated0.00127 [.000050] min. nickelNote: Accepts 0.08-0.09mm2 [28 AWG]ribbon cable, PVC insulated 1.00 [.039]pitch. See Application Specification fordetails.


Mateable Connectors — pages 9and 12, or see Application Specificationfor header requirements

AccessoriesPull Loops — page 66Keying Plugs — page 64Strain Relief — page 68

8.48[.334]

5.16[.203]

A

2.00[.079]Typ.

2.00[.079]Typ.

1.90 ± 0.05[.075 ± .002]

10.24[.403]

4.000[.1575]

B

Position Number1 Indicator

Position Number 1

Terminated View, Typical

METRICDimensions are

Optional Center Polarizer Bar

1.54[.061]

5.00[.197]

No. of Dimensions Center Non-PolarizedPositions A B Polarized

8 13.18 8.41 3-111623-0 2-111626-4.519 .331

10 15.16 10.41 1-111623-8 1-111626-7.597 .410

12 17.15 12.40 3-111623-1 —.675 .488

14 19.18 14.40 1-111623-9 1-111626-8.755 .567

16 21.18 16.41 2-111623-0 2-111626-5.834 .646

20 25.17 20.40 2-111623-1 1-111626-9.991 803

22 27.18 22.40 2-111623-9 —1.070 .882

24 29.18 24.41 2-111623-7 2-111626-61.149 .961

26 31.17 26.42 2-111623-2 2-111626-71.227 1.040

30 35.18 30.40 2-111623-3 —1.385 1.197

34 39.17 34.42 2-111623-8 2-111626-01.542 1.355

40 45.19 40.41 2-111623-4 2-111626-11.779 1.591

44 49.17 44.40 2-111623-5 2-111626-21.936 1.748

50 55.17 50.39 2-111623-6 2-111626-32.172 1.984





AMPMODU 50/50 Grid Connector System


Produced under a QualityManagement Systemcertified to ISO 9001A copy of thecertificate is availableupon request.

Vertical Headers,Board-to-Board(Page 21)

Vertical Headers,Board-to-Board(Page 21)

Right-Angle Headers,Board-to-Board (Page 24)

Vertical Headers,Board-to-Board(Page 21):.250 [6.35] Stack Height.320 [8.13] Stack Height.390 [9.91] Stack Height

Vertical Receptacles,Board-to-Board(Page 20)

Vertical Receptacles,Board-to-Board(Page 20)

Receptacles,Cable-to-Board,With Latch(Page 26)

Receptacles,Cable-to-BoardWithout Latch(Page 26)

ISO

Certifie

d9001

Boar

d-to

-Boa

rdVe

rtic

alR

ecep

tacl

esan

dH

eade

rs




Board-to-Board Vertical Receptacles and Headers


Product Facts� Surface-mount products for

parallel board-to-boardapplications, as well asright-angle board-to-boardand cable-to-boardapplications

� High density .050 x .050[1.27x1.27] centerline grid

� Three board-to-board stackheights: .250 [6.35], .320[8.13] and .390 [9.91]

� Non-protrusive metallicholddowns

� Reliable dual beamreceptacle contacts forredundant contact

� Duplex plated receptacleand post contacts; goldplated on mating areas,tin plated on tails

� Compatible with standardsurface-mount processing(VPR and IR)

� Receptacle and headerallow for drainage ofprocessing fluids

� Tape and reel packagingavailable. ContactTyco Electronics for details

� Polarized header andreceptacle assemblies

� Sizes of 10, 20, 30, 40, 50,60, 70, 80 and 100 positions

� Recognized under theComponent Program ofUnderwritersLaboratories Inc.,File No. E28476

� Certified byCanadian StandardsAssociationFile No. LR7189

AMPMODU 50/50 GridVertical Headers andReceptacles are designedfor parallel board-to-boardstacking in high densityapplications.

Right-angle board-to-boardand cable-to-boardapplications are alsopossible, since the verticalreceptacles also mate withnon-latching right-angleheaders (page 24) and thevertical headers also matewith non-latching cableconnectors.

Available are double row,vertical shrouded headersand receptacles in sizesranging from 10 through100 positions (in 10 positionincrements).

Parallel board-to-boardstack heights of .250 [6.35],.320 [8.13] and .390 [9.91]are achievable by selectionof the appropriate header.The receptacle is the samefor all three stack heightheaders.

Non-protrusive metallicholddowns are designed foruse in .062 [1.57] or thicker

PC boards and allow surfacemounting to both sides ofthe board. In addition toproviding retention duringprocessing, the holddownsare soldered during reflowand therefore providelong-term strain relief forthe solder joints.

AMPMODU 50/50 GridVertical Headers andReceptacles are designedto be compatible withstandard surface-mountprocesses; IR (infrared) andVPR (vapor phase reflow).The surface-mountconnectors have beendesigned so thatdimensioning, tolerances,referenced datums,holddown characteristics

and packaging methodsresult in a system that iscompatible with roboticassembly.

The headers and receptaclesfeature polarization toprevent misalignment.

Three Board Stack Heights

Non-ProtrusiveMetallic Holddowns

.250±.006[6.35±0.15]

.320±.006[8.13±0.15]

.390±.006[9.91±0.15]

R

R

Board-to-BoardVertical

Receptacles

andH

eaders




Board-to-Board Vertical Receptacles, Double Row, .050 x .050[1.27 x 1.27] Centerline


Vert

ical

Rec

epta

cles

,D

oubl

eR

ow


Material and FinishHousing—Glass-filled thermoplastic,black, 94V-0 ratedContacts—Copper alloy; duplex plated.000030 [0.00076] gold in mating area,.000150 [0.00381] tin on solder tail,with entire contact underplated .000050[0.00127] nickelHolddown—Copper alloy; plated.000150 [0.00381] tin over .000050[0.00127] nickel

Related Product DataMating Headers — pages 21 and 24PC Board Layouts — page 22Performance Specifications —page 29

Technical Documents — page 29Product Specification 108-1332Application Specification114-7010Packaging — Tube or Tape and Reel

No. of DimensionReceptacle

Pos. APart Numbers

Tube Tape and Reel* No Hold Down w/Vacuum Cover10 .266 [6.75] 5-104652-1 5-147384-1 5-147413-120 .516 [13.11] 5-104652-2 5-147384-2 5-147413-330 .766 [19.46] 5-104652-3 5-147384-3 5-147413-440 1.016 [25.81] 5-104652-4 5-147384-4 —50 1.266 [32.16] 5-104652-5 5-147384-5 5-147413-260 1.516 [38.51] 5-104652-6 5-147384-6 —70 1.766 [44.86] 5-104652-7 5-147384-7 —80 2.016 [51.21] 5-104652-8 5-147384-8 —100 2.516 [63.91] 6-104652-0 5-147384-9 —

* Parts packaged in tape and reel have vacuum pick and place cover.See PC Board Layout on page 22.

Polarizing Tab(For Polarization toMating Header)

A .028[0.71]

.187[4.75]

.120[3.05]

.050[1.27]

.050[1.27]

.050[1.27]




Board-to-Board Vertical Headers, Double Row, .050 x .050[1.27 x 1.27] Centerline


VerticalHeaders,

Double

Row


Material and FinishHousing—Glass-filled thermoplastic,black, 94V-0 ratedContacts—Copper alloy; duplex plated.000030 [0.00076] gold in mating area,.000150 [0.00381] tin on solder tail,with entire contact underplated .000050[0.00127] nickelHolddown—Copper alloy; plated.000150 [0.00381] tin over .000050[0.00127] nickel

Related Product DataMating Receptacles — pages 20and 26 (without latch only)PC Board Layouts — page 22Performance Specifications —page 29

Technical Documents — page 29Product Specification 108-1332Application Specification114-7010Packaging — Tube or Tape and Reel

Header Part Numbers

No. of Dimension .250 [6.35] Mated Height .320 [8.13] Mated Height .390 [9.91] Mated HeightPos. A

TubesTape & Reel*

Tubes Tape & Reel*Tubes

Tape & Reel*Hold Down No Hold Down Hold Down No Hold Down

10 .372 [9.44] 5-104655-1 5-147381-1 5-147121-1 5-104656-1 5-147382-1 5-104693-1 — 5-147383-120 .622 [15.79] 5-104655-3 5-147381-2 5-147121-2 5-104656-2 5-147382-2 5-104693-2 — 5-147383-230 .872 [22.14] 5-104655-4 5-147381-3 — 5-104656-3 5-147382-3 5-104693-3 — 5-147383-340 1.122 [28.49] 5-104655-5 5-147381-4 — 5-104656-4 5-147382-4 5-104693-4 — 5-147383-450 1.372 [34.84] 5-104655-6 5-147381-5 — 5-104656-5 5-147382-5 5-104693-5 — 5-147383-560 1.622 [41.19] 5-104655-7 5-147381-6 — 5-104656-6 5-147382-6 5-104693-6 — 5-147383-670 1.872 [47.54] 5-104655-8 5-147381-7 — 5-104656-7 5-147382-7 5-104693-7 — 5-147383-780 2.122 [53.89] 5-104655-9 5-147381-8 — 5-104656-8 5-147382-8 5-104693-8 — 5-147383-890 2.372 [60.24] — — — 5-104656-9 — 5-104693-9 — —100 2.622 [66.59] 6-104655-1 5-147381-9 — 6-104656-0 5-147382-9 6-104693-0 5-147503-1 5-147383-9

*Parts packaged in tape and reel have vacuum pick and place cover.See PC Board Layout on page 22.

For .250 [6.35] Mated Height



.050[1.27]

.050[1.27]

.050[1.27]

.030[0.76]

.030[0.76]

.050[1.27]

.2255[5.728]

.225[5.71]

.2975[7.557]

.3675[9.335]

A

A

A

.030[0.76]

.050[1.27]




Recommended PC Board Layouts for Vertical Connectors


Rec

omm

ende

dPC

Boar

dLa

yout

s

No. of Receptacle Dimensions Header DimensionsPos. B C D B C D

10 4 .200 [5.08] .320 [8.12] 4 .200 [5.08] .322 [8.17]20 9 .450 [11.43] .570 [14.48] 9 .450 [11.43] .572 [14.52]30 14 .700 [17.78] .820 [20.83] 14 .700 [17.78] .822 [20.87]40 19 .950 [24.13] 1.070 [27.19] 19 .950 [24.13] 1.072 [27.22]50 24 1.200 [30.48] 1.320 [33.53] 24 1.200 [30.48] 1.322 [33.57]60 29 1.450 [36.83] 1.570 [39.88] 29 1.450 [36.83] 1.572 [39.92]70 34 1.700 [43.18] 1.820 [46.23] 34 1.700 [43.18] 1.822 [46.27]80 39 1.950 [49.53] 2.070 [52.58] 39 1.950 [49.53] 2.072 [52.62]90 44 2.200 [55.88] 2.320 [58.93] 44 2.200 [55.88] 2.322 [58.97]100 49 2.450 [62.23] 2.570 [65.28] 49 2.450 [62.23] 2.572 [65.32]

D

D

.029[0.74]

B Spaces at .050 [1.27] = C

B Spaces at .050 [1.27] = C

C of Pattern

Detail A

Detail A

C of Pattern

.061[1.54]

.050[1.27]

.162[4.11]

.182[4.62]

.091[2.31]

.110[2.79]

.050[1.27]

.060[1.52]

.065[1.65]

.130[3.30]

.029[0.74]

L

L

Headers

Receptacles

Note: Refer to Tyco ElectronicsCustomer Drawings for additionalPC board layout information anddimensional tolerances.

.047[1.19]2 Plc.

.010[0.25]4 Plc.

Detail A




Board-to-Board Right-Angle Headers


Board-to-BoardR

ight-AngleH

eaders

AMPMODU 50/50 GridRight-Angle Headers willaccommodate a variety ofhigh density packagingapplications; right-angleboard-to-board applicationswhen mated with verticalreceptacles (page 20) andright-angle cable-to-boardapplications when matedwith cable connectors(page 26). The small.050 x .050 [1.27 x 1.27]centerline contact spacingallows efficient use of thePC board area.

Mechanical support of theheaders to the PC board isprovided by non-protrusivemetallic holddownsdesigned for .062 [1.57] orthicker PC boards. Theseholddowns are of the same

design as those used in thevertical headers (page 21)and receptacles (page 20).There are also metallic tabsthat are soldered to the sur-faces of the PC board padsfor added support.

AMPMODU 50/50 GridRight-Angle Headers areavailable in double-row, ineither latching or non-latching versions, and insizes ranging from 10through 100 positions (in 10position increments). Thelatching version providespositive retention whenmated with the latchingcable connector (page 26).All headers feature polar-ization to help prevent mis-alignment during mating.

Product Facts� Surface-mount products for

right-angle board-to-boardand cable-to-boardapplications

� Double-row, right-angleshrouded headers

� High density .050 x .050[1.27 x 1.27] centerline grid

� Latching and non-latchingversions available

� Non-protrusive metallicholddowns

� Metallic tabs, whensoldered to PC board pad,provide added mechanicalsupport

� Duplex plated post contacts;gold plated on mating area,tin plated on tails

� Compatible with standardsurface-mount processing(VPR and IR)

� Standoffs on headerhousings allow for drainageof processing fluids

� All headers are polarized� Sizes of 10, 20, 30, 40, 50,

60, 70, 80 and 100 positions� Recognized under the

Component Program ofUnderwritersLaboratories Inc.,File No. E28476

� Certified by CanadianStandardsAssociationFile No. LR7189

R

R




Board-to-Board Right-Angle Headers, Double Row, .050 x .050[1.27 x 1.27] Centerline


Rig

ht-A

ngle

Hea

ders

,D

oubl

eR

ow,

Latc

hing

and

Non

-Lat

chin

g


Material and FinishHousing — Liquid crystal polymer,black, 94V-0 ratedContacts — Copper alloy; duplexplated .000030 [0.00076] gold inmating area, .000150 [0.000381] tin onsolder tail, with entire contact under-plated .000050 [0.00127] nickelHolddown — Copper alloy; plated.0000150 [0.00381] tin over .000050[0.00127] nickel

Related Product DataMating Receptacles — pages 20and 26Performance Specifications —page 29

Technical Documents — page 29Product Specification 108-1443Application Specification114-7010Packaging — Tube

Recommended PC Board Layout

No. of DimensionsHeader

Pos.Part Numbers

A B C D Latching Non-Latching10 .630 [16.00] 9 .225 [5.72] .550 [13.97] 5-104895-1 5-104894-120 .880 [22.35] 19 .475 [12.07] .800 [20.32] 5-104895-2 5-104894-230 1.130 [28.70] 29 .725 [18.42] 1.050 [26.67] 5-104895-3 5-104894-340 1.380 [35.05] 39 .975 [24.77] 1.300 [33.02] 5-104895-4 5-104894-450 1.630 [41.40] 49 1.225 [31.12] 1.550 [39.37] 5-104895-5 5-104894-560 1.880 [47.75] 59 1.475 [37.47] 1.800 [45.72] 5-104895-6 5-104894-670 2.130 [54.10] 69 1.725 [43.82] 2.050 [52.07] 5-104895-7 5-104894-780 2.380 [60.45] 79 1.975 [50.17] 2.300 [58.42] 5-104895-8 5-104894-8100 2.880 [73.15] 99 2.475 [62.87] 2.800 [71.12] 6-104895-0 6-104894-0

A

.430[10.92]

.340[8.64]

.305[7.75]

B Spaces at.025 = C[0.64]

.085[2.16]

.140[3.56]

.175[4.45]

D

.100[2.54]Min

.063[1.57](2 Plc)

.190[4.83](2 Plc)

.047 Dia[1.19]Plated-Thru Hole(2 Plc)

.136[3.45](2 Plc)

.050[1.27]

.352[8.94]

.213[5.41]

.050[1.27]

.050[1.27]Typ.

.029[0.74]Typ

.065[1.65]Typ.

Note: Refer to Tyco ElectronicsCustomer Drawings for additionalPC board layout information anddimensional tolerances.

Non-Latching Header

Latching Header




Cable-to-Board Connectors


Cable-to-BoardConnectors

Product Facts� Double-row receptacle

connectors provide cable-to-board connectioncapabilities for verticalheaders (non-latching) andright-angle headers(latching and non-latching)

� IDC (InsulationDisplacement Crimp) masstermination of solid orstranded round conductor.050 [1.27] centerlineribbon cable with PVC orpolyethylene insulation

� Accommodates ribbon cableconductor sizes of 28 AWG[0.08-0.09 mm2] and 30AWG [0.05 mm2] andinsulation diameters up to.036 [0.91] maximum

� Reliable single beamreceptacle contact design

� Duplex plated receptaclecontacts; gold plated inmating area, tin intermination area

� Terminating covers (soldseparately) provide bothstrain relief and protectionto the termination area

� Sizes of 10, 20, 30, 40, 50,60, 70, 80 and 100 positions

� Connectors available with orwithout metal latch

� Connectors without latchesare polarized to helpprevent mismating

� Recognized under theComponent Program ofUnderwritersLaboratories Inc.,File No. E28476

� Certified by CanadianStandardsAssociationFile No. LR7189

These double-row cableconnectors, with a .050 x.050 [1.27 x 1.27] centerlinecontact spacing, providecable-to-board connectioncapabilities for theAMPMODU 50/50 GridConnector System. Cableconnectors without a latchwill mate with the verticalheaders (page 21), whilecable connectors with orwithout a latch can be usedto mate with the right-angleheaders (page 24).

The cable connectorsfeature reliable single-beam IDC (insulationdisplacement crimp)contacts which are duplexplated with .000030[0.00076] gold. Thesecontacts can be massterminated to either solid or

stranded round conductorribbon cable with conductorsizes of 28 AWG [0.08-0.09mm2] and 30 AWG [0.05mm2] and a maximuminsulation diameter of .036[0.91]. During termination,the terminating covers,which must be purchasedseparately, assist in guidingthe wire into the IDCcontacts, then providestrain relief when fullyseated. Actual terminationis accomplished with theTyco Electronics manualtooling shown on page 28.

The latching version ofthe cable connector isequipped with a metal latchwhich provides positiveretention of the receptaclecable connector whenmated with a surface-

mounted right-angle header.The cable connector withouta metal latch featurespolarization to help preventmismating. All connectorsare available in sizesranging from 10 through100 positions (in 10 positionincrements).

R

R




Cable-to-Board Receptacle Connectors, Double Row, .050 x .050[1.27 x 1.27] Centerline


Rec

epta

cle

Conn

ecto

rs,

Dou

ble

Row

,W

ithan

dW

ithou

tLat

ch


Material and FinishHousing — Thermoplastic, black,94V-0 ratedLatch — Stainless steelContacts — Phosphor bronze; duplexplated .000030 [0.00076] minimumgold in mating area, .000150 [0.00381]minimum tin on solder tail, with entirecontact underplated .000050 [0.00127]minimum nickel

Related Product DataMating Headers — pages 21 and 24(latching)Terminating Covers (Must bePurchased Separately, 2 Requiredper Connector) — page 27Termination Tooling — page 28Performance Specifications —page 29

Technical Documents — page 29Product Specification 108-1443Application Specification408-9817, 408-9909Packaging — Tube

A

No. of DimensionsReceptacle

Pos.Part Numbers

A B C D With Latch Without Latch10 .578 [14.68] 4 .200 [5.08] .266 [6.76] 5-104892-1 5-104893-120 .828 [21.03] 9 .450 [11.43] .516 [13.11] 5-104892-2 5-104893-230 1.078 [27.38] 14 .700 [17.78] .766 [19.46] 5-104892-3 5-104893-340 1.328 [33.73] 19 .950 [24.13] 1.016 [25.81] 5-104892-4 5-104893-450 1.578 [40.08] 24 1.200 [30.48] 1.266 [32.16] 5-104892-5 5-104893-560 1.828 [46.43] 29 1.450 [36.83] 1.516 [38.51] 5-104892-6 5-104893-670 2.078 [52.78] 34 1.700 [43.18] 1.766 [44.86] 5-104892-7 5-104893-780 2.328 [59.13] 39 1.950 [49.53] 2.016 [51.21] 5-104892-8 5-104893-8100 2.828 [71.83] 49 2.450 [62.23] 2.516 [63.91] 6-104892-0 6-104893-0

.280[7.11]

.627[15.94]

.690[17.56]

D

.120[3.05]

B Spaces at.050 [1.27] = C

.284[7.21]

.327[8.31]

.050[1.27]

.050[1.27]Typ




Terminating Covers for Cable Connectors


CableConncetor

Terminating

Cover,D

oubleR

ow


MaterialGlass-filled thermoplastic,black, 94V-0 rated

Related Product DataConnectors used with Covers —page 26Termination Tooling — page 28

Technical Documents — page 29Product Specification 108-1443Application Specification408-9817, 408-9909Packaging — Plastic bag

No. of Dimension Terminator CoverPos. A Part Numbers10 .565 [14.35] 104891-120 .815 [20.70] 104891-230 1.065 [27.05] 104891-340 1.315 [33.82] 104891-450 1.565 [39.75] 104891-560 1.815 [46.10] 104891-670 2.065 [52.45] 104891-780 2.315 [58.80] 104891-8100 2.815 [71.50] 1-104891-0

Note: Terminating covers must be purchased separately, two are requiredfor each cable connector.

.277[7.04]

.191[4.85]

A




Application Tooling for Cable Connectors


IDC

(Ins

ulat

ion

Dis

plac

emen

tCri

mp)

Tool

ing


Manual Miniature Application Frame Assembly 91295-1with Cover Closing Kit 543518-1

The Manual MiniatureApplication FrameAssembly 91295-1,equipped with a CoverClosing Kit 543518-1, isused for the IDC termina-tion of ribbon cable to thecable connectors shown onpage 26.

Prior to termination, thecovers must be partiallyassembled onto a connec-tor housing, the cableinserted between the cov-ers and contacts and thecovers preclosed by hand,clamping the cable inplace.

In the Manual MiniatureApplication FrameAssembly, the covers arefully seated to completethe mass termination andprovide strain relief for thecompleted connection.

For tooling information, callTechnical Support Center1-800-522-6752.

Note: Refer to Tyco ElectonicsInstruction Sheets 408-9817 (frameassembly 91295-1) and 408-9909(cover closing kit 543518-1) forcomplete termination/tooling infor-mation.




Performance Specifications


Performance

Specifications/TechnicalD

ocuments


Board-to-Board Connectors, Vertical and Right-AngleMating Force — 6.4 oz (1.78 N] max. per contactUnmating Force — 1.0 oz [0.28 N] min. per contactDurability — Tested to 200 cycles min.Current Rating — (30°C T rise): .5 ampere per contactOperating Temperature Range — -65°C to +105°CTermination Resistance — 16 milliohms max. (initial)Insulation Resistance — 5000 megohms min. (initial)Dielectric Withstanding Voltage — 300 VAC

Cable-to-Board ConnectorsMating Force — 6.4 oz (1.78 N] max. per contactUnmating Force Without Latch — .5 oz [0.14 N] min. per contactDurability — Tested to 200 cycles min.Current Rating — (10°C T rise); .5 ampere per contactOperating Temperature Range — -65°C to +105°CTermination Resistance — 25 milliohms max. (initial and final)Insulation Resistance — 5000 megohms min. (initial)Dielectric Withstanding Voltage — 300 VAC

Technical Documents

Various technical documents are available for your use:

Product Specifications describe technical performance characteristics and verificationtests. They are intended for the Design, Component and Quality Engineer.

108-1332 AMPMODU 50/50 Grid Vertical Board-to-Board Connectors

108-1443 AMPMODU 50/50 Grid Right-Angle Board-to-Board and CableConnectors

Application Specifications describe requirements for using the product in its intendedapplication and/or crimping information. They are intended for the Packaging and DesignEngineer and the Machine Setup Person.

114-7010 AMPMODU 50/50 Grid Connector System

Instruction Sheets provide instructions for assembling or applying the product. They areintended for the Manufacturing Assembler or Operator.

408-9817 Manual Miniature Application Frame Assembly 91295-1

408-9909 Cover Closing Kit 543518-1




Micro-MaTch Miniature Connector System


Micro-M

aTch

Miniature

ConnectorSystem

Miniaturization and thetrend towards higher den-sity of electronic functionson a substrate led to theintroduction of smallerinterconnection systems.The Micro-MaTch connectorfamily, with it’s contactspacing of 1.27 mm, fullycomplies with the electronicpackaging requirements oftoday and the future. Thesystem offers a range ofboard and wire connectors,enabling a variety of wire-to-board and board-to-board interconnections.The Micro-MaTch contactshown on this page isessentially different fromother systems available.

By its design the traditionalfailure mode in tin platedconnections, fretting corro-sion, is prevented. Due toan additional positioningspring in the female part,

relative movements causedby vibrations/thermalexpansion between maleand female contacts areabsorbed. By preventingmovements on the contactspot, a gas tight connectioncan be guaranteed underall circumstances.

The contact spring islocated in the board con-nector and not in the cableconnector, which is usuallythe case. The counter part,incorporated in the cableconnector, is a simple pin,either with an insulation dis-placement section, suitablefor the mass-termination ofcable or with a kinked sol-der leg to be soldered ontoa PC Board. The separationof these two basic functionsof the contact system —contact force generationand wire termination —enables the independent

optimization of both func-tions and also leads torelatively simple contactshapes.

Because of their shapescontacts can be post-plated, leaving no bareedges in the contact andwire slot area. The contactspring system features anadditional spring member— the positioning spring —which compensates posi-tional tolerances. In thisway the contact spring canbe fully optimized for itsbasic function, so that therelatively high contact force,required for tin platedcontact systems, can beguaranteed under allcircumstances.

The Micro-MaTch contactspring system is absolutelyfretting corrosion proof byits design.

Features/ Benefits� Available in 2 to20 positions

� Applicable Wire:20~28 AWG

� Wire connectors suppliedon-tape and suitable formass termination of28 AWG [0.08 mm2 to0.09 mm2] ribbon cable

� Tin plated contact design

� Guaranteed minimumcontact force of 2.0 N

� Fretting corrosion proofthanks to additionalpositioning springmember

� Full range of applicationtooling from hand tool tofully automated equipment

1. Contact Pin

2. Contact Spring

3. Positioning

1

2

3




Micro-MaTch Miniature Connector System Overview Technical Data


Micro-M

aTchMiniature

ConnectorSystem

Overview

TechnicalData

Technical DataCenterline: 1.27 mm (staggered)Number of Positions: 4, 6, 8, 10, 12, 14, 16, 18, 20, and some 24 positionsContact Material: Phosphor bronzeContact Finish: Tin over NickelHousing Material: Thermoplastic polyester, red, glass-filled

For surface mount versions polyamide 4.6Flammability rating: per UL 94 V-0UL-recognized: File E28476 Vol. 23 Section 4Contact Resistance: 10 MΩ max.Insulation Resistance: 1.000 MΩ min.Nominal Voltage: 230 VCurrent Rating: 1.5 A max.Temperature Range: -40° C to +105° C (operating)Mating Force: 5N max. per contactUnmating Force: 1N min. per contactMinimum Contact Force: 2N min.Product Specification: 108-19052Application Specification: 114-19016, 114-19051RoHS Compliance Code: Always RoHS compliant (directive 2002/95/EC) for all typesLead-free Process Capable: Wave solder capable to 265° C for through hole versions

reflow solder capable to 260° C for SMD versions

PC Board ConnectorsPC Board Thickness: 1.6 mm nominalPC Board Hole Diameter: 0.8 mm for solder connectors

Ribbon ConnectorsCable Type: Ribbon cable, UL Style 2651Conductor Spacing: 1.27 mm (.050")Conductor Diameter: Solid 0.30 mm diameter Stranded 0.08 mm2

7 x 0.12 - 0.13 mm (other diameters and/or configurationson request)

Insulation Type: semi-rigid PVCInsulation Diameter: 0.9 ± 0.1 mm

Discrete Wire (COSI) ConnectorsCable Type : AWG 28-24 and 24-20




Micro-MaTch Miniature Connector System Applications (3 Dimensions)


Micro-M

aTch

Miniature

ConnectorSystem

Applications

(3Dim

ensions)

Female Connectors

Male Connectors

Female Top Entry Part Number 215079

Male-on-WirePart Number 215083

Male-on-BoardPart Number 215464

COSIPart Number 338095Part Number 338096Part Number 338097

Paddle BoardPart Number 215570

Female Side Entry Part Number 215460

SMD Top EntryPart Number 188275

1 2 3

4 5/6 7

8 9 10

Image Description (see also page 33)1 Wire-to-Board through hole2 Board-to-Board through hole3 Wire-to-Board (discrete wire), through hole4 Wire-to-Board right angle, through hole5 Board-to-Board right angle, through hole6 Board-to-Board right angle, through hole7 Wire-to-Board right angle (discrete wire), through hole8 Wire-to-Board surface mount9 Board-to-Board surface mount, through hole10 Wire-to-Board (discrete wire), surface mount




Micro-MaTch Miniature Connector System Applications (2 Dimensions)


Micro-M

aTchMiniature

ConnectorSystem

Applications(2

Dim

ensions)

B

A

C

AC

B

C

A

B

C

A

B

C

D

A

E

B

C

D

A

B

D

A

C

B

D

A

B

D

A C B

CGE

C BA

CD

F

Female Top Entry Part Number 215079

Male-on-WirePart Number 215083

Male-on-BoardPart Number 215464

COSIPart Number 338095Part Number 338096Part Number 338097

Paddle BoardPart Number 215570

Female Side EntryPart Number 215460

SMD Top EntryPart Number 188275

1 2 3

45

76

8 9 10

Female Connectors

Male Connectors

Dimensions (mm)Image

A (max) B (max) C D (max) E (max) F(max) G (max)1 5.2 7.5 2.54 — — — —2 5.2 6.2 2.54 — — — —3 5.2 9.7 2.54 — — — —4 8.4 5.9 2.54 1.5 — — —5 5.2 5.9 2.54 1.5 7.0 1.6 —6 5.2 5.9 2.54 1.5 — — 2.87 5.2 5.9 2.54 1.5 10.6 — —8 5.2 8.5 — 7.1 — — —9 5.2 7.1 2.54 7.1 — — —10 5.2 10.7 — 7.1 — — —




Micro-MaTch Miniature Connector System —Female-on-Board Connector, Top Entry


Micro-M

aTch

Miniature

ConnectorSystem

—Female-on-Board

Connector,TopEntry

This connector versionincorporates the Micro-MaTch contact spring sys-tem and is designed to besoldered onto PC Boardswith a nominal thickness of1.6 mm.

The solder legs areindented, providing firmretention of the connectorbefore and during thesoldering operations.

As polarization is accom-plished directly betweenthe Micro-MaTch male con-nectors and the PC Board,this top entry female con-nector does not have anypolarizing features.Therefore, the orientation ofthe connector on the PCBoard is irrelevant.

1.5[.059]

1.27[.050]

A

B Max.

3.1[.122]

1.9[.074]

4.0[.157]

5.1[.200]

Max.

2.54[.100]

2.54[.100]

1.27[.050]

1.40[.055]

1.80[.071]

1.50[.059]

0.80[.031]

Hole forPolarization Pin

Typical Hole PatternNot Solder Side Shown

No. of PositionsDimensions (mm) Part NumbersA B 2500 Connectors/Reel 250 Connectors/Box

4 3.81 7.1 215079-4 7-215079-46 6.35 9.7 215079-6 7-215079-68 8.89 12.2 215079-8 7-215079-810 11.43 14.7 1-215079-0 8-215079-012 13.97 17.3 1-215079-2 8-215079-214 16.51 19.8 1-215079-4 8-215079-416 19.05 22.4 1-215079-6 8-215079-618 21.5