river/waterfall (lk955) · german, french and spanish instructions are enclosed. for additional...

German, French and Spanish instructions are enclosed. For additional tips and techniques, using Woodland Scenics products, read The Scenery Manual (C1207), or visit our Web site at www.woodlandscenics.com. Scale Model Material • MADE IN USA • ©2002 OCO Fig. 1 Fig. 2 Fig. 5 Fig. 6 Fig. 7 Fig. 9 Fig. 8 Fig. 10 Fig. 3 waterfall masking tape Realistic Water Burnt Umber Earth Undercoat Black Pigment dampened paper towels Plaster Cloth cut and remove traced contours Fig. 4 Talus Scenic Glue Green Grass Instructions-River/Waterfall NOTE: Read instructions thoroughly before starting. Use these products on an existing layout. If you do not have an existing layout, use cardboard or a flat surface and proceed to step 2. Realistic Water will make a river approximately 2 1/2” wide x 9” long x 1/8” deep. Water Effects will create a waterfall approximately 1 1/4” wide x 5” long x 3/32” thickness. Water Effects coverage will vary depending on the thickness of your waterfall. 1. Trace and cut outline of the river/waterfall area and remove (Fig. 1). 2. Wad newspapers to form contours. Use dampened paper towels to build up banks (Fig. 2) and let it dry completely before applying Plaster Cloth. 3. Cut Plaster Cloth into 3" strips and dip into water (Fig. 3). Cover entire area, applying Plaster Cloth bumpy side up (Fig. 4). Smooth Plaster Cloth with fingers until holes are filled. Allow to dry. 4. Mix each of the Earth Colors Liquid Pigments with one tablespoon of water in three separate cups. Apply colors in water area, darker colors simulating deep areas and lighter colors shallow areas (Fig. 5). Allow to dry. 5. Mix Scenic Glue with water, 50/50; save part of mixture to adhere Talus. Brush Scenic Glue mixture over river bank (Fig. 6). Blend Green Grass into existing landscaping, on top of Scenic Glue mixture, along river bank and blow off excess (Fig. 7). 6. Brush Scenic Glue mixture in areas where Talus will be placed (Fig. 8). Sprinkle Talus onto these areas and apply remainder of Scenic Glue mixture over Talus with an eyedropper. Dry thoroughly. 7. Apply masking tape, tightly, against the edge of the layout to prevent runoff. Pour Realistic Water slowly on upper and lower levels (Fig. 8). Keep it 1/4" away from edge of waterfall when pouring upper level. Dry 24 hours. 8. To make waterfall, apply enough Water Effects to a non-stick surface using a craft stick. Save a small amount of Water Effects to adhere waterfall. Water Effects should be the width and 1/2" longer than the height of the waterfall area. Texture waterfall and feather ends with toothpick (Fig. 9). Dry for 24 hours. Peel up and press to waterfall, using Water Effects as an adhesive on the back of waterfall (Fig. 10). Apply Water Effects at the top and bottom of waterfall and sculpt water with toothpick to make splashes and rapids. Allow to dry thoroughly. Anleitungen, Fluss/Wasserfall River/Waterfall (LK955)

Upload: others

Post on 19-Mar-2020

2 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: River/Waterfall (LK955) · German, French and Spanish instructions are enclosed. For additional tips and techniques, using Woodland Scenics products, read The Scenery Manual (C1207),

German, French and Spanish instructions are enclosed.For additional tips and techniques, using Woodland Scenics products, read The Scenery Manual (C1207),

Fig. 1 Fig. 2

Fig. 5 Fig. 6 Fig. 7

Fig. 9Fig. 8 Fig. 10

Plaster Plaster Cloth

Fig. 3

water

toothpick

non-stick surface

Water Effects(waterfall) waterfallmasking tapemasking tape

Realistic Water

Burnt Umber

Earth Undercoat

Black PigmentBlack PigmentBlack Pigment

newspaper wads

newspaper

dampened paper towelspaper towelsdampened

paper towelsdampened

Plaster Clothcut and remove traced contours

Fig. 4

Talus

Scenic Glue Green Grass

Instructions-River/WaterfallNOTE: Read instructions thoroughly before starting.Use these products on an existing layout. If you do not have an existing layout, use cardboard or a flat surface and proceed to step 2. Realistic Water will make a river approximately 2 1/2” wide x 9” long x 1/8” deep. Water Effects will create a waterfall approximately 1 1/4” wide x 5” long x 3/32” thickness. Water Effects coverage will vary depending on the thickness of your waterfall.1. Trace and cut outline of the river/waterfall area and remove (Fig. 1).2. Wad newspapers to form contours. Use dampened paper towels to build up banks (Fig. 2) and let it dry completely before applying

Plaster Cloth.3. Cut Plaster Cloth into 3" strips and dip into water (Fig. 3). Cover entire area, applying Plaster Cloth bumpy side up (Fig. 4). Smooth

Plaster Cloth with fingers until holes are filled. Allow to dry.4. Mix each of the Earth Colors Liquid Pigments with one tablespoon of water in three separate cups. Apply colors in water area, darker

colors simulating deep areas and lighter colors shallow areas (Fig. 5). Allow to dry.5. Mix Scenic Glue with water, 50/50; save part of mixture to adhere Talus. Brush Scenic Glue mixture over river bank (Fig. 6). Blend

Green Grass into existing landscaping, on top of Scenic Glue mixture, along river bank and blow off excess (Fig. 7).6. Brush Scenic Glue mixture in areas where Talus will be placed (Fig. 8). Sprinkle Talus onto these areas and apply remainder of Scenic

Glue mixture over Talus with an eyedropper. Dry thoroughly.7. Apply masking tape, tightly, against the edge of the layout to prevent runoff. Pour Realistic Water slowly on upper and lower levels

(Fig. 8). Keep it 1/4" away from edge of waterfall when pouring upper level. Dry 24 hours.8. To make waterfall, apply enough Water Effects to a non-stick surface using a craft stick. Save a small amount of Water Effects to

adhere waterfall. Water Effects should be the width and 1/2" longer than the height of the waterfall area. Texture waterfall and feather ends with toothpick (Fig. 9). Dry for 24 hours. Peel up and press to waterfall, using Water Effects as an adhesive on the back of waterfall (Fig. 10). Apply Water Effects at the top and bottom of waterfall and sculpt water with toothpick to make splashes and rapids. Allow to dry thoroughly.

Anleitungen, Fluss/Wasserfall

River/Waterfall (LK955)

SDLC Model (Waterfall,Iterative Waterfall,Spiral)

Project Management Methodologies · pure waterfall model, modified waterfall models were introduced, such as "Sashimi (Waterfall with Overlapping Phases), Waterfall with Subprojects,

1. Western Guns - Steiner Scenics · 2019. 11. 20. · Double Barreled pistol 5. Philadelphia Derringer 6. English flintlock pistol 7. Kentucky flintlock pistol . Steiner Scenics

BUILD REMOVABLE SCENERY • MAKE EASY BACKGROUND … · woodland scenics scenery cement. 2. Sprinkle on ﬁne ground foam leaves. 3. Add full trees to foreground. 4. Quick background

LEARNING KIT - Woodland Scenics

Woodland Scenics' The Scenery Kit

Scenics by Dean Huggins

SCENERY DESIGN

Walthers October 2019 Flyeraws.walthers.com/October2019Flyer-cons_61-71.pdf63 SCENERY Coniferous Tree Pack - Ready Made Trees Woodland Scenics. 785-1580 2-1/2 to 4" 6.4 to 10.2cm pkg(33)

55987649 scenery