s22 ml4 sm7 airu v1.2 eng - servonaut.de€¦ · soundmodul sm7 or sm3 receiver (c) tematik gmbh...

1
Mini- Lichtanlage ServoNaut ML4 BAT - BAT+ + L R 1 2 Classic Xenon Receiver + EQ on Motor Setup EQ off BAT+ BAT- SM+ Fahrtregler/ESC SM7 Sound tematik GmbH ServoNaut Made in Germany + Horn/Starter - Card 7,2V 4 Ω 12V8Ω + VOL - + F3 F4 V2.2 F1/2 ServoNaut AIR-U IR-Transmitter tematik GmbH Made in Germany Stand/Side Brems/Brake Rück/Reverse Links/Left Rechts/Right SF 6 / SF 8 Battery + Tamiya Servo 5 Servo 6 Andere Diode Diode Tam MFC-01/03 Batt+ Batt - Motor Motor + Sound Bremse ServoNaut Rev.Light S22 20A 16kHz 3A BEC tematik GmbH V6 Made in Germany 7,2V & 12V NiCd/NiMH Fahrtregler / Electronic Speed Controller Empfänger / Receiver + Brake Rücklicht + 7,4V(2S) & 11,1V(3S) Lipo 1 2 3 4 5 7 8 Motor 6 9 (1) (2) (3) (4) (5) (6) (7) (8) (9) Rear 12V Lämpchen bei 12V 6V Lämpchen bei 7,2V Front IR-Transmitter to AMO in the trailer Speaker 8 Ohm for 12V 4 Ohm for 7,2V Volume Soundmodul SM7 or SM3 Receiver (c) tematik GmbH www.servonaut.de Mini light set Steering servo Gear servo (optional) Please use a good quality high current connector which is reverse polarity protected. We recommend at least 1,5mm² (AWG16) for battery and motor wires. Make sure that the motor is fitted with a suppressor kit of 2 or 3 capacitors (Servonaut ENT kit). The servo cable between S22 and receiver is the power supply for all servos (BEC). Please dont`t extend these cables. You might connect plus of all lamps to battery plus or "+ Light" of the S22 as well. You can also use LEDs instead of lamps but don`t forget appropriate resistors. We recommend our Servonaut Cable Harnesses L3V/H or L312V/H. At least one of the servo cables 5 and 6 of the AIR-U must be connected to the receiver, even if the function is not used in the trailer. Special functions F3 and F4 are not commonly used - you can leave these open. For details look at the SM7 manual. Typical use of channels shown for Robbe/ Futaba radios. The channel numbering might be different for other radios and setups. - + 7,2 V - 12 V Battery Left indicator Side & rear light Braking light Reversing light Braking light Side & rear light Right indicator Left indicator Side light Driving light Driving light Side light Right indicator 9 8 7 6 5 4 3 2 1 -x -x -Trailer servo func. 6 -Trailer servo func. 5 -Gear servo -ML4 Light set -S22 Speed controller -SM7 Horn/Starter -Steering servo Wiring Diagram S22 + ML4 + SM7 + AIRU

Upload: others

Post on 01-Sep-2019

29 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: S22 ML4 SM7 AIRU V1.2 ENG - servonaut.de€¦ · Soundmodul SM7 or SM3 Receiver (c) tematik GmbH Mini light set Steering servo Gear servo (optional) Please use a good quality high

Min

i-

Lic

hta

nla

ge

Serv

oNaut

ML

4

BAT

-B

AT

++ L R 1 2

Cla

ssic

Xe

no

n

Receiver

+

EQ onMotor SetupEQ off

BAT+

BAT -

SM+

Fahrtregler/ESC

SM7Sound

tematik GmbH

ServoNautMade in Germany

+

Horn/Starter - Card

7,2

V4

Ω 12V→

+

VOL- +

F3

F4

V2.2

F1 / 2

Servo

Naut A

IR-U

IR-T

ran

smitte

r te

ma

tik Gm

bH

Ma

de

in G

erm

an

y

Stand/Side

Brems/Brake

Rück/Reverse

Links/Left

Rechts/Right

SF 6 / SF 8

Battery +

Tamiya

Servo 5

Servo 6

Andere

Diode

Diode

Tam MFC-01/03

Batt+

Batt -Motor

Motor

–+

Sound

Bremse

ServoNautRev.Light

S22

20A 16kHz 3A BEC

tematik GmbH V6 Made in Germany

7,2V & 12V NiCd/NiMH

Fahrtregler / Electronic Speed Controller

Empfänger / Receiver

+

Brake

Rücklicht

+

7,4V(2S) & 11,1V(3S) Lipo

1

2 3

4

5

7

8

Motor

6

9

(1)(2)(3)

(4)

(5)

(6)

(7)

(8)

(9)

Rear

12V Lämpchen bei 12V 6V Lämpchen bei 7,2V

Front

IR-Transmitter to AMO in the trailer

Speaker8 Ohm for 12V4 Ohm for 7,2V

Volume

Soundmodul SM7 or SM3

Receiver

(c) tematik GmbH www.servonaut.de

Mini lightset

Steeringservo

Gear servo(optional)

Please use a good quality high current connector which is reverse polarity protected.We recommend at least 1,5mm² (AWG16) for battery and motor wires.Make sure that the motor is fitted with a suppressor kit of 2 or 3 capacitors (Servonaut ENT kit).The servo cable between S22 and receiver is the power supply for all servos (BEC). Please dont`t extend these cables.You might connect plus of all lamps to battery plus or "+ Light" of the S22 as well.

You can also use LEDs instead of lamps but don`t forget appropriate resistors. We recommend our Servonaut Cable Harnesses L3V/H or L312V/H.At least one of the servo cables 5 and 6 of the AIR-U must be connected to the receiver, even if the function is not used in the trailer.Special functions F3 and F4 are not commonly used - you can leave these open. For details look at the SM7 manual.Typical use of channels shown for Robbe/ Futaba radios. The channel numbering might be different for other radios and setups.

-+

7,2 V - 12 V

Battery

Left indicator

Side & rear light

Braking light

Reversing light

Braking light

Side & rear light

Right indicator

Left indicator

Side light

Driving light

Driving light

Side light

Right indicator

9

87

6

5

4

3

2

1

-x

-x

-Trailer servo func. 6-Trailer servo func. 5-Gear servo-ML4 Light set-S22 Speed controller-SM7 Horn/Starter-Steering servo

Wiring Diagram S22 + ML4 + SM7 + AIRU