safety track anti-skid tape › pdfs › pirsf007_pi.pdf · for treatment, recovery and...
TRANSCRIPT
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 1 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid TapeSlip prevention protects against injuries and saves money
Serious injuries caused by slips and falls in the workplace not only affect human lives, they can have a debilitating impact on the financial welfareof the business. Billions of dollars are lost each year due to medical costsfor treatment, recovery and rehabilitation, compensation, lost work days,and litigation.
Here are some startling national statistics:
LOST WORK DAYS PER YEAR: 329,100Source: Occupational Hazards, 2010
AVERAGE PER-INCIDENT COST: $13,000Source: Occupational Hazards, 2010
AVOIDABLE SLIP ACCIDENTS Reported Per Year: 17,229Source: National Safety Council, 2010
Percentage of Slip-Related WORKER'S COMPENSATIONCLAIMS: 85%Source: Business Wire, 2010
Annual SLIP-RELATED COSTS for Medical Expenses, LostWork Days, Litigation: over $70BSource: National Safety Council, 2010
Why is slip guarding important?In addition to injury prevention, slip guarding is also required bycertain OSHA (Occupational Safety and Health Administration), andADA (Americans with Disabilities Act) regulations.
OSHA 29 CFR 1910.22(a)(1) states:“All places of employment, passageways, storerooms, and servicerooms shall be kept clean and orderly and in a sanitary condition.”
ADA 28 CFR Part 36 Appendix A Section 4.5.1 States:“Ground and floor surfaces along accessible routes and in accessiblerooms and spaces including floors, walks, ramps, stairs, and curbramps, shall be stable, firm, and slip-resistant.”
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 2 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid Tape (cont.)Why choose Lawson’s Safety Track® Safety Tape?Safety Track® commercial-grade, non-skid grit tape has been designed for most general purpose applications. This product was engineered to exceed OSHA standards by providing a durable, consistent non-slip surface.
The use of silicon carbide grit ensures the longevity in both indoor and outdoor applications. By coating our own adhesives, we can assure the most aggressive, durable adhesive system on the market today.
Safety Track® Product Line OverviewCommercial Grade Non-Slip Rolls and Treads - 80 Grit • General purpose non-slip tape to help ensure safe footing on slippery surfaces • Superior resistance to chemicals and fluids • Good for indoor and outdoor applications • Certified by NFSI (National Floor Safety Institute) for “High Traction”
Commercial Grade - Colors - Non-Slip Rolls and Treads - 60 grit • An effective way to offer visual warning of a slip and fall hazard • Superior resistance to chemicals and fluids • Good for indoor and outdoor applications • Available in 7 popular colors • Also available in a mop friendly version • Certified by NFSI (National Floor Safety Institute) for “High Traction”
Resilient Rolls and Treads • Rubberized, textured, non-slip tape is designed for heavy traffic, but comfortable for bare feet • Ideal for both commercial and industrial applications • Mop-friendly for easy cleanup. • Good for indoor and outdoor applications • Certified by NFSI (National Floor Safety Institute) for “High Traction”
Conformable Safety Track®
• Foil backed tape designed for adhesion to irregular surfaces • Ideal for ladder rungs, corners, diamond plate, etc. • Excellent temperature stability • Good for indoor and outdoor applications
Heavy-Duty Grade Non-Slip Rolls and Treads • 46 Grit • Premium high-traction, non-slip tape for heavy-duty, harsh environment applications • Coarser surface to help reduce the risk of slips and falls • Oil, fluid, and grease resistant • Good for indoor and outdoor applications • Certified by NFSI (National Floor Safety Institute) for “High Traction”
Photoluminescent Non-Slip Tape • Ultimate non-slip egress tape that provides unsurpassed non-slip protection • Perfect safety-grade, glow-in-the-dark solution for marking stairs and corridors that are part of the emergency egress route. • Absorbs and stores energy from ambient light and is instantly visible in the dark • Certified by NFSI (National Floor Safety Institute) for “High Traction”
Commercial Grade
Commercial Grade - Colors
Resilient
Conformable (not NFSI certified)
Heavy Duty
Photoluminescent
®
®
®
®
®
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 3 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid Tape (cont.)
Common Applications
Airline Decks/Cargo HoldsATVs/SnowmobilesAuto Repair ShopsBath AreaBathtubsBoatsBusesCatwalksCold StorageConstruction EquipmentConveyorsDiving BoardsFarm MachineryFood Service AreasFork Lifts/Cherry PickersGaragesGarden TractorsJet SkisLaddersLawn MowersLoading DocksMachine ShopsPlatforms/RampsPool AccessoriesPulleysRecreational VehiclesScaffoldsSemi-TrailersShip DecksShowersStep StoolsSteps, Stairs, PlatformsSurf boardsSwimming PoolsTrainsWater SkisWet and Oily Areas
Table I - Product Selection Guide
Heavy-DutyGrade
XXX
XXXX
X
XXX
XXXX
X
XX
X
X
CommercialGrade
XXX
XXXXXX
XXXXX
XXXX
XXXXX
XXX
XXX
Resilient
X
XX
XXXX
XXXX
XXXX
X
Photo-luminescent
XXX
XXXXXX
XXXXXXXXXXX
XXXXX
XXX
XXX
General Purpose
ConformableXXX
XXXX
X
XXX
XXXXX
XXXX
X
X
X
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 4 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid Tape (cont.)
Table II - Typical Properties of Anti-Slip Tape
Table IV - Friction GuideKinetic Coefficient of Friction
Shoe Sole Type
Non-Skid Material Type
Heavy-Duty Grade
Commercial Grade
Resilient
Photoluminescent
General Purpose Conformable
Leather
0.74
1.01
0.58
0.81
0.74
Wet Leather
1.37
1.55
0.84
1.35
1.37
Rubber
0.93
1.13
1.06
0.93
0.93
Wet Rubber
1.11
1.20
1.18
0.83
1.11
Table III - Chemical Resistance Guide
R - Recommended I - Intermittent ExposureNR - Not Recommended IC - Incidental Contat with immediate cleanup
Chemical
BLEACHMEKMINERAL SPIRITSGASOLINEDIESEL FUELTRICHLORETHYLENEWATER50% ANTIFREEZEIPA25% SULFURIC ACID1% SODIUM HYDROXIDEHYDRAULIC FLUIDDETERGENT
HeavyDuty
Grade
RNRRICR
NRRRRI
ICRR
General Purpose
Conformable
RNRRICR
NRRRRI
ICRR
CommercialGrade
RNRRICR
NRRRRI
ICRR
Resilient
RNRRICR
NRRRRI
ICRR
Photoluminescent
RNRRICR
NRRRRI
ICRR
Immediate24-Hour
PSTC-1 ModifiedPeel Adhesion
Property
ColorApplied Thickness
Minimum Surface Application Temperature
Maximum Service Temperature
Minimum Service Temperature
Grit Type
Heavy Duty Grade
Black0.35
80 oz/1 in.130 oz/1 in.
50ºF10ºC150ºF66ºC-20ºF-29ºC
Silicon Carbide
General PurposeConformable
Black0.35
80 oz/1 in.130 oz/1 in.
50ºF10ºC150ºF66ºC-20ºF-29ºC
Silicon Carbide
Photoluminescent
Photoluminescent0.25
80 oz/1 in.130 oz/1 in.
50ºF10ºC150ºF66ºC-20ºF-29ºC
Aluminum Oxide
Resilient
Black/Grey0.25
43 oz/1 in.53 oz/1 in.
50ºF10ºC150ºF66ºC-20ºF-29ºCN/A
Colors0.25
80 oz/1 in.130 oz/1 in.
50ºF10ºC150ºF66ºC-20ºF-29ºC
Aluminum Oxide
Black0.275
80 oz/1 in.130 oz/1 in.
50ºF10ºC150ºF66ºC-20ºF-29ºC
Silicon Carbide
Commercial Grade
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 5 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid Tape (cont.)
Table V - Surface Preparation Recommendations
Substrate Material
Bare MetalBare PlasticsBare Wood
Ceramic TileEpoxy-Coated Floor
Gel-Coated FiberglassMarble
Painted MetalPainted or Coated Smooth Concrete
Painted PlasticsQuarry Tile
Rough or Smooth Porous ConcreteTerrazzoVinyl Tile
Strip Floor Finish, Degrease, Wash and Rinse
XXXXXXXXXXX
Solvent Wipe*
XX
XX
X
X
Prime Coat Required***
X
XX
* A solvent-based or di-limonelene cleaner such as Lawson’s Bonafide or Quick Peel should be used.** A detergent or degreasing cleaner such as Lawson’s Keynote should be used*** A zinc phosphate primer such as Lawson’s Green Phosphate Primer should be used to treat bare wood or pourous substrates.
Surface Preparation Instructions
1. Remove chipped, cracked or peeled paint prior to application of Anti-Slip Tape.
2. Remove loose residue from surface.
3. Make sure surface is clean, dry, smooth, and above the minimum application temperature of 50°F (10°C). Repair or replace any broken or damaged surface.
4. Any floor sealer or finish (wax) should be removed prior to application. (Fig. 1)
5. Refer to the Surface Preparation Table (Table V) for recommendations of proper cleaning products to be used in surface preparation. (Fig. 2)
6. After surface has dried, mask area and prime surface if necessary. (Fig. 3)
Note: All porous and non-ferrous substrates need to be primed.
7. After primer has dried, follow the application instructions to ensure product has its best chances at a long service life.
Fig. 1
Fig. 3
Fig. 2
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 6 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid Tape (cont.)
Priming Instructions
1. Prime clean, dry surfaces with a high-quality zinc-oxide primer (like Lawson’s Green Phosphate Primer) especially when: a) bare and untreated concrete is present. b) coated, painted or porous concrete surfaces are excessively rough. c) other porous surfaces such as wood is the substrate.
2. Properly clean the surface using the methods found in the Surface Preparation Recommendations Table. (Ref. Table V)
3. Mask the area around location of tread. (Fig. 4) Maintain at least ½” from the edges of the substrate.
4. Apply primer using the spray can, or use a brush to apply a thin coat of primer where tread is to be placed. Note: if the surface is porous a second coat of primer may be necessary. (Fig. 5)
5. Allow primed area to dry thoroughly (no evidence of tackiness should be present) before applying tread material.
Application Instructions
1. Individual pieces should be spaced a minimum of ½” apart and a maximum of 2” apart. Maintain ½”spacing from edges of substrate.
2. Round the corners of any treads cut from a roll. This will prevent the corners from coming up during service. (Fig. 6)
3. Peel Protective liner back about 2” from one end and position piece on surface. (Fig. 7) IMPORTANT: Minimize touching adhesive with fingers.
4. Continue to remove liner. Press firmly in place as liner is removed.
5. For small pieces, peel liner off piece. Holding piece by its edges, curve it gently with adhesive side out. Align with the middle of the target surface and press down.
Fig. 4
Fig. 6
Fig. 5
Fig. 7
PRODUCT INFO REPORT
1.866.LAWSON4U 1.866.529.7664 www.lawsonproducts.com Contact engineering at [email protected]© Lawson Products, Inc.
Page 7 of 7PIRSF007 REV. 3/12
Automotive Chemicals Cutting Tools/Abrasives
Electrical Fasteners Fluid Power Safety/ Material Handling
Shop Supplies/Hand Tools
Welding
Safety Track® Anti-Skid Tape (cont.)
Application Instructions (cont.)
6. Tap the tread using a rubber mallet or soft faced hammer around the perimeter and center of tread. This will ensure good contact with the substrate. (Fig. 8)
Edge Sealing Instructions
1. Using a rubber mallet or soft faced hammer, tap the edges of the tread down to make sure the edges are properly adhered to the substrate.(Fig. 8)
2. Using a high quality, solvent based sealing compound such as Lawson’s Clearmaster, draw an 1/8” bead around the tread. IMPORTANT: Do not use RTV Silicone to seal the edges. RTV will not adhere properly and will come up during service. (Fig. 9)
3. Using a body filler spreader, or stiff card spread the sealant down feathering the edges flush with the substrate and tread. (Fig. 10)
4. Allow edge sealant to cure to tack free before allowing foot traffic to the area.
Maintenance Instructions
1. Keep free of dirt and other residue that might impair functionality.
2. Treads should be brushed or swept regularly.
3. Resilient tapes and treads should be mopped regularly.
Commonly Used Related Products
Keynote Heavy Duty Cleaner Mop Bonafide Solven Nitrile Disposable Gloves Tractitie Concrete Repair Compound Safety Glasses Clearmaster Sealant and Caulk Wypeall X80 Shop TowelsGreen Phosphate Primer Razor Edged ShearsOut-Strip Chemical Stripper Auto-Load Utility KnifeCaulk Gun Carbon Steel Scratch Brush2” Wide Masking Tape Power Drive Soft Face Hammer
Fig. 8
Fig. 10
Fig. 9