salt system quick-start guide - wordpress.com

Salt System Quick-Start Guide 1. Clean Tub & New or Clean Filter(s) Fill spa with fresh water. After full, jets must be on to circulate the water while adding chemicals to effectively distribute throughout entire tub. 3. Fill spa and circulate water with jets 10. Circulate water for 1 - 2 hours and retest Start with an empty, clean tub and new or clean ﬁlter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer system.) Allow water to circulate to equilibrate spa chemicals for an hour or two (or overnight) then retest; adjust if necessary. (800) 823-3638 Mon-Fri 6 AM - 5 PM PST Follow label instructions according to your spa’s capacity guidelines. 2. Install Salt Cell/Chlorine Generator Sal tron Install the Saltron Mini salt cell/chlorine generator per the manufacturer’s instructions. The cell should be inspected every 3 months for scaling deposit. If scale exists, the cell should be cleaned with diluted Acid Magic per manufacturer’s instructions. 9. Shock water with Oxy-Spa 7. Add Metal Free 6. Add natural clarifier Add 1 oz. of natural clariﬁer per 500 gallons of spa water, weekly. Add Metal Free stain/metal preventer per label instructions. 4. Add Premium Dead Sea Mineral Salts 5. Test water Slowly add 2 lbs of Premium Dead Sea Minerals per 100 gallons. Disperse over the surface and allow salt to dissolve for at least 20 minutes. Total Alkalinity (TA): 80 - 120 ppm pH: 7.2 - 7.6 Water Hardness: 150 - 300 ppm Chlorine: 3.0 - 4.0 ppm Test water for Alkalinity and pH with Chlorine 4-in-1 Test Strips; adjust if necessary using Alkalinity Increaser or pH Decrease. Check water with Hardness Test Strips, if under 150 ppm, add Increase Calcium. Salinity: 2,000 - 3,000 ppm C O A R S E G R A I N U N S C E N T E D D e a d S e a S a l t S A L T W O R K S 1 0 0 % P U R E B O K E K ™ D E A D S E A S A L T TE S T FOR S A L T MPS 3-in1 Test Strips Total Hardness MPS 3-in1 Test Strips Total Hardness 8. Add Dichlor/Stabilizer Add Dichlor Stabilizing granules to establish a chlorine reserve. At startup, add 2 tablespoons per 500 gallons. Pro Supplies Kit #KT1012 Add 1 tablespoon non-chlorine MPS Oxy-Spa per 250 gallons of spa water at startup. After each spa use, add 1 - 2 tablespoons Oxy-Spa.

Upload: others

Post on 21-Feb-2022

1 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: Salt System Quick-Start Guide - WordPress.com

Salt System Quick-Start Guide1. Clean Tub & New or Clean Filter(s)

Fill spa with fresh water. After full, jets must be on to circulate the water while adding chemicals to effectively distribute throughout entire tub.

3. Fill spa and circulate water with jets

10. Circulate water for 1 - 2 hours and retest

Start with an empty, clean tub and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer system.)

Allow water to circulate to equilibrate spa chemicals for an hour or two (or overnight) then retest; adjust if necessary.

(800) 823-3638Mon-Fri 6 AM - 5 PM PSTFollow label instructions according to your spa’s capacity guidelines.

2. Install Salt Cell/Chlorine GeneratorSaltronmini

Install the Saltron Mini salt cell/chlorine generator per the manufacturer’s instructions.The cell should be inspected every 3 months for scaling deposit. If scale exists, the cell should be cleaned with diluted Acid Magic per manufacturer’s instructions.

9. Shock water with Oxy-Spa

7. Add Metal Free

6. Add natural clarifier

Add 1 oz. of natural clarifier per 500 gallons of spa water, weekly.

Add Metal Free stain/metal preventer per label instructions.

4. Add Premium Dead Sea Mineral Salts

5. Test water

Slowly add 2 lbs of Premium Dead Sea Minerals per 100 gallons. Disperse over the surface and allow salt to dissolve for at least 20 minutes.

Total Alkalinity (TA): 80 - 120 ppm pH: 7.2 - 7.6 Water Hardness: 150 - 300 ppmChlorine: 3.0 - 4.0 ppm

Test water for Alkalinity and pH with Chlorine 4-in-1 Test Strips; adjust if necessary using Alkalinity Increaser or pH Decrease. Check water with Hardness Test Strips, if under 150 ppm, add Increase Calcium.

Salinity: 2,000 - 3,000 ppm

natural

COARSE GRAINUNSCENTED

Dead Sea Salt

SALTWORKS 100% PURE BOKEK™ DEAD SEA SALT

TESTFORSALT

FASTEASY

ACCURATE

MONOPERSULFATE (MPS)

TOTAL ALKALNITY

MPS3-in1

Test Strips