sbc9302 procedure
DESCRIPTION
SBC9302 ProcedureTRANSCRIPT
-
OVERVIEW.!Basic of ARM9 Controller.
Important Steps.
Linux installation.
SPJ tools installation i.e. workspace
installation.
How to operate board of ARM9
Controller.
-
STEPS.!Features of ARM9 i.e.SBC_9302.
Installation of Linux_Mandriva.
Installation of MINICOM Terminal
& TFTP server.
Ethernet Setup.
Workspace Installation
TFTP Setting & Bash profile Setting.
-
FEATURES!
ARM9 ControllerEP9302 32Bit.
Cirrus Logic Controller EP9302 &
Speed_ @200 Mhz.
Ethernet Support 10 to 100Mbps.
USB Device & USB Host.
-
FEATURES!
RAM Memory SDRAM_32MB.
Flash Memory_16MB.
Serial Port Support:-
RS232,RS485/RS422
Memory Card Interface.
-
FEATURES!
Channel:-
1. 16 bit ADC Channel.
2. PWM Channel.
SD Card Interface.
104 PC Expansion Bus.
-
LINUX
INSTALLATION!
Space For Installation :- 40 GB to
80 GB
Partition :-
1. Root (/):- 16 GB to 25 GB.
2. Swap:- 4 GB to 8 GB.
3. Home:- Remaining space.
-
LINUX
INSTALLATION!
Graphical User Interface:-
1. KDE(K Desktop
Environment).
Installation Packages.
MBR(Memory Boot Reader).
-
MINICOM
TERMINAL!
-
Double Click on "Install & Remove Software
1.Firstly Go to start
-
This window will appeared.
-
1.Here Find minicom & install it i.e. click on Apply button..2.All process Given below,3.Important Notes:- In Mandriva_2010 Minicom must be installed externly,Only these procedure is available in Mandriva_2007 .4.So in Mandriva_2010 It must be install external
-
Such window will appeared & Then say Yes
1.When above process gets completed then our Minicom will installed successfully.
-
EXTERNAL COPY PROCESS!
Firstly copy binary file of minicom from CD sbc9302_tools in Home of Linux operating system which is on Desktop.
Then open konsole terminal . Then give command su & press enter also need of root
password. After root login give command cd /home/maahi(user name)/ &
press enter. Then give command ls & press enter "for ensure that we are
in home folder . Then give command cp minicom /usr/bin/ & press enter Our minicom binary file will be copied at its destination.
-
TFTP
SERVER.!
-
Double Click on "Install & Remove Software
-
This window will appeared.
-
This Window will appeared. Then Find TFTP
tftp
select All "here.
-
Find TFTP & select last two option.
-
Such window will appeared & Then say Yes
When bellows process gets completed then our TFTP server will install successfully.
-
MAKE!
-
Also find make & select Make Say "apply
-
Such window will appeared & Then say Yes
-
GCC(GNU Code
Compiler.)!
-
Find gcc & Select it
-
Say Apply
-
Such window will appeared & say Apply
-
After Installation .Click on Quit button.
-
Select Security Option & above option will appeared!
-
click on Set up your personal firewall icon.
-
Select Everything (no firewall) icon & say OK.
-
Right click here & select Network configuration above window will appeared.
-
Select Wired(Ethernet) & say Next.
-
Such window will appeared Select eth0& then say "Next
-
Such window will appeared Then select "Manual configuration& then say "Next
-
Such window will appeared then Give require IP address You can give any & fill all these thing given here . say "Next
-
Such window will appeared Select last two option then say "Next
-
Such window will appeared Select Yes& then say "Next
-
1.Firstle open console terminal as shown below.2.Then give command su -3.Then give our root password. 4.All process shown below,
-
1.After that just give command shown as below i.e. cd /home/maahi(user name)/Desktop/cd_image(folder name)/
Then press "enter2.Now we are in our folder where we have copy on Desktop.
-
Here we can ensure that we are in destination folder by giving command ls as shown below.i.e.It show file which is in our folder.
-
1.Here for workspace installation we required to run any file from,a.gui_install.dh. b.install.sh. c.user_install.sh. d.install_original.sh.
2.Here I am running file user_install.sh by giving command sh user_install.sh such as shown below.3.Aftre giving command press enter.
-
1.Such window will appear, here enter our user name & press enter.
-
1.After giving our user name ,give our path where sbc9302tools are copied i.e.on Desktop.2.Then press enter. & press y For installing our workspace again press enter.3.All process shown below,
-
1.When our workspace is installed at home then it shows message given below,
2.Our workspace will be installed at home as sbc9302
-
1.Firstly open console terminal.2.Give command su press enter & give our root password then press enter.3.After give command vim /etc/xinetd.d/tftp/ & press enter.4.All process given below,
-
1.Such window will appear.2.For insert word press shift+i.2.Then set path such as -c s /home /maahi(user name)/maahi/tftpboot/ & press esc key.3.Finaly press :wq & press enter. Our path will be set .((:wq ) is saving command).
-
1.Firstly open folder which is on Desktop as sbc9302.2.Open Pdf file i.e. user manual_9302.3.Then find path & select these path i.e. Copy these path as shown below,
-
1.Firstly open home & go to view< Select show hidden file.2.Double click on bash_profile i.e.open bash_profile
-
1.Here set path which is copied from sbc9302 tools user manual . From desktop. 2. Path is shown below,
Paste path here
-
1.Open console terminal ,then give command su press enter.2.Give our root password & press enter.3.Give command minicom s & press enter.4. All process shown below,
-
1.Such window will appear.2.Then select serial port setup& press enter.3.All process shown below.
-
1.Such window will appear, here make all setting like picture such as given below,2.When we press letter i.e. A to G we can edit these setting.3.We need only change in serial Device,Boud rate, Hardware flow control.
-
1.After making of all setting save these setting permantly select save setup as dfl & press enter.2.After that select "exit & press enter.3.Our minicom will be initialize.
-
1.Such window will appear .2.Here we can connect our SBC9302 Project board.