service manual - revivebusinesssolutions.comrevivebusinesssolutions.com/whirl/manuals/whirlpool...
TRANSCRIPT
Service ManualModel: Sunrise WFS1073DD
Contents
1、 Technical data ------------------------------2
2、 Parts list -------------------------------------4
3、 Exploded Views ---------------------------6
5、 Failure/Alarm conditions-------------------9
6、 Wiring Diagrams --------------------------12
Fully Automatically Washing Machine
This documentation is only intended for qualified technicians who are aware of the respective safety regulations.
Date: Jan. 30 2011
- 1 -
4、 Tes + program ------------------------------8
7、 Electricel Diagram-------------------------13
8、 Program Chart-----------------------------15
- 2 -
Technical data Dimensions
Height 85 cm Width 60 cm Depth 60 cm
Weight
With packing 80 kg Without packing 75 kg
Main connection
Voltage 240 V Frequency 50 Hz Power consumption 2.3 kW Fuse rating 10 A
Drum
Volume 54 l Wash speed 40/54rpm Ramp speed 90rpm Speed spinning max. 1000 rpm
Pressostat for washing-machine
Level1Switching point 55 ± 5 mmWcReset 30 ± 5 mmWc
Overflow Switching point 300± 20 mmWc
Water column drum
Level1 Switching point 31 - 42 mm
Overflow Switching point 267 - 306 mm
Nominal current Contacts: 11-12 10mA 11-14 10mA 11-16 10mA Contactsystem: 11-12-14 jump contacts 11 - 16 slow action contacts
Door lock Lock time 3“ -6“ (20°C) Unlock time 60“ -90“ Nominal voltage 230 V Nominal current: contact:
3–5 10mA 4–5 16A
Heating element Kind of heating Tubular heating element
with NTC- Sensor Australia
Nominal voltage 240 V Nominal power 1900 W Heat conductor
resistance 30.3±5% Ω Resistanc NTC:
0°C 35.9 kΩ 30°C 9.8 kΩ 40°C 6.6 kΩ 50°C 4.6 kΩ 60°C 3.2 kΩ 70°C 2.3 kΩ 95°C 1.1 kΩ
Inlet valve Water temperature 60 °C Pressure range 0.2 - 10 bar Nominal voltage 220 - 240 V Frequency 50/60 Hz Nominal current 35 mANominal power 6 VANominal resistor( 20°C ) 3,82 ±10% kΩ Starting voltage:
(coil temperature 25 C°,0.2 to 10 bar):<160V (coil temperature 100C°,0.2 to 8 bar):<160V (coil temperature 100C°,0.2 to 10 bar):<170V
Flow tate:
0.3 to 1.0 bar 8L/min+15%-50% 1.0 to 1.5 bar 8L/min±8% 1.5 to 5.0 bar 8L/min±5%
5 to 10 bar 8L/min±8%
- 3 -
Technical data
Drain pump (synchronus)
Nominal voltage 220-240 (+6%-15%) V Nominal current 0.3 A Nominal consumption 34 WFrequency 50±3 HzResistor (coil) 160 ± 7% Ω Motor protection no Capacity (1.25m height) 14± 2 l/min
Electronic complete
Type C1 Nominal voltage 230 V Frequency 50 Hz Detergent Dispenser 3 Chamber Programmes 18 Speed 1000 rpm Cold fill yes Ambient temperature to 0~60 °C Storage temperature to –25°C ~85 °C
Motor Type HXG45B05.WH01
i = 1 : 15.9
- 4 -
WFS1073DD spare parts listCode Part No Description
10 4619 704 1081 painted cabinet bracket assm. 210 4619 704 2290 painted front panel 240 4619 704 2209 rear panel 250 4619 704 2310 control brace 300 4619 704 2178 table top WH 06 400 4619 710 2066 door hinge complete 610 4619 704 1066 top counterweight cpl. 611 4619 704 1096 bottom counterweight cpl. 810 461 971 07525 Damper cpl,531 862 461 971 03217 stopper for damper fix 1100 4619 710 8130 handle1300 4619 710 1570 plate door lock upper 1301 4619 710 2109 plate door lock lower 1400 4619 704 2891 door glass 1430 4619 704 1867 door frame 1440 4619 710 8136 door back support 1910 4619 710 8356 Bellow1911 4619 710 1647 steel wire,bellow&front panel 1912 4619 740 9167 steel wire,bellow&tub 2000 4619 704 1105 front tub asmbly 2010 4619 704 1045 rear tub pre_asmbly 2200 4619 704 1071 drum+shaft+cp 2710 4619 704 2305 Belt2720 4619 710 8888 Pulley2920 4619 704 3307 sealing of tub 3030 4619 704 2232 handle drawer WH 06
3210 W10384872 CONSOLE ASM, WFS1073DD
3310 4619 714 0028 knob
4000 W10282201 motor for 1000 electronic(with Tapped field)
4210 4619 704 2378 RFI for 600/800/1000 4300 4619 704 3598 Leili PumP for AUS 4510 4619 704 2388 heating element for AUS 4910 46197 102 2461 strain relief
5210 W10382913 CCU, PROGRAMMED, WFS1073DD
5730 4619 704 3590 double valve 5820 4619 704 1954 pressure switch 6300 4619710 1915 spring, door lock 6530 4619 704 2304 Ig program flow WH 06 8x 7010 4619 710 50522 inlet hose forAustralia(cold)
7110 46197041163 dispenser box, with hot inlet for China
- 5 -
7531 4619 710 1663 airtrap_assy
7540 4619 704 1813 Hose tub to pump
7810 4619 704 1043 Drain hose assembly
7870 4619 704 1812 hose dispenser to tub
9300 4619 704 1130 Suspension spring assy.
0020 46197502140 Adjustable foot
0260 46197042173 Hose value to disperser left cold
0270 46197042174 Hose value to dispenser right cold
4220 46197042389 Wire harness
6200 W10347553. VI bard.
6210 46197042392 Wire timer-VI
3040 46197048866 Logo badge WH
Testprogram
1. Switch the appliance ON
2. Close the door
For appliances withprogram selection
by knob
3. Select the “DRIN” cycle
4. Press push button Reset 4 times within 5 seconds
5. To go to next step, press push button Reset twice
Attention: Use the test program only without laundry!ICON - Phases
DigitsTempera-
ture
Description of the Program Flow Check to perform
<—> Icons arc switched on and off in a sequence from loft to right and
back
CO The door is locked. The CUC is performing the Selftest
CUC detects • F02, F05, F08, F12, F13, F14,
F15, F21, F23, F26
C1
Fill 8' hot valve (only if hot fill appliance)Fill 8' in prewash (PW) Fill 8' in mainwas-h <MW) Fill 8' in PW + MW (Softener) Fill by MW to wash level. Motor is reversing
Technician: • Check the valve activation • Check the dispensing into the
dispenser • Check the pressure switch
C2 The heating element is switched ON Motor is reversing
Technician: • Check heating element activation• Check if the motor is reversing CUC dctccts: • F05, F07, F27
C3 The drain pump is switched ON until thewash level = OFF ♦ 5' motor is reversing
Technician: • Chock drain pump activation • Check prossuro switch operation• Chock if the motor is rovorsing CUC detects: • F06, F07, F27, F03
C4 The motor is driven to maximum speed.
Drain pump is ON.
Technician: • Check if the motor is running at
max speed • Check drain pump activation CUC dctccts: • F28
C5 Motor is switched OFF. Door is unlocked
Technician: • Check if the door is unlocked CUC dctccts: • F13
Digits of "Rest time" are executing an animation, Digits of "Speed" are OFF
- 8 -
- 9 -
Failure/Alarm conditions
ErrorCode Alarm Code
Device/Failure Detected inStep/ Routine
Detection Indication/ Reaction
none Door unlockfailure
_WHTest stepMotorTest
Before restarting a cycle the door has to beunlocked. Means the transition from SELECTION to EXECUTION is possible only if the DoorLock_IN == OFF
Exception is if during ProgramEnd andRestart there was a mains interrupt detected.
All Actuators = OFFIt’s for Domino Low (C1)Timer,which indirect the failure status by phase control LED.
1 Water TapClosed Alarm
Subroutine_Fill() The LevelWash is not reached within a
defined time(EEPROM parameter).
opMode = Pause
2 Aquastopfailure
Function_ReadLevelOv f() WHTeststep AutoTest
the Aquastop switch was activated See _ErrorMode / FA
24 Overflowfailure
Function_ReadLevelOv f()WHTest stepAutoTest
The Overflow contact was activated 5times within a wash cycle
See _ErrorMode / F24The failure Code will be displayed while failure event occurs for the Models keeping LED display or LCD display
3 Drain filterAlarm
Subroutine_Drain()
The LevelWash_In is not switched OFF aftera predefined 4 minutes draining
opMode = Error
4 Heater failure( open heater circuit)
Subroutine_Wash( )
the temperature temperature < 40°C after 40min of heating
opMode = Error / F04
5 NTC failure(open circuit, short circuit)
PW,MW1,MW2_ReadNTC()_WHTest stepAutocheck
detects a value of the NTC out of the range opMode = Error / F05
- 1 0 -
6 No tachometer:signal
MotorManager_WHTest Step MotorTest
Normal cycleIf here are 10 occurences of no tacho feedback during the same wash phase. WH Test: only 2 trials
opMode = Error / F06
7 Motor triac SC
WHTeststep AutoTest
MotorManager
Normal cycle:If there the motorspeed is not controlled thenswitch OFF the motor and wait for the speed = 0 +10“At the second occurence in the same wash phase go to ERROR modeWH Test: only 1 trial
opMode = Error / F07
8 Heater failure _OpStart_OpFinish by_HeaterSafety
Failure detected in heater circuitsee subroutine _HeaterSafety
opMode = Error / F08
12 Heater failure _OpStart_OpFinish by_HeaterSafety
Failure detected in heater circuitsee subroutine _HeaterSafety
opMode = Error / F12
14 EEPROMfailure
Function_ReadEEPRO M
the CRC of the read page is not correctand the page is not a wash page
opMode = Error / F14
18 Foam /Oversuds detected
Subroutine_Spin()
counter_A == 0 or counter_B == 0 opMode = Error / Fod
- 11 -
Error Code Alarm Code
Device /Failure
Detected inStep /Routine
Detection Reaction
15 DrumUpfailure
_WHTeststepMotorTest
The DrumUp switch is not closed duringdrum rotationDetected only in _WHtest and_WHService procedure
opMode = Error / F15
23 PressureSwitch failure The Level Wash and the Level Heater
Safety are switched On in the same time (>10“) see subroutine _ReadLevelWash
opMode = Error / F23
26 Pump triacfailure( Diode Mode)
_ReadLevelOv f
_WHTeststep AutoTest
Pump Triac in Diode Mode or Driver PumpTriac defective
Detected when Door is locked in DELAY, PAUSE,EXECUTION; Not detected during cycle Drain
opMode = Error / F26
21 User Interfacefailure
_WHTeststep AutoTest
User Interface E1 is not detected opMode = Error / F21
13 Door LockTimeOut
_WHTeststep AutoTest
Managed during Test program opMode = Error / F13
27 Reversing relaybroken
_WHTeststepMotorTest
Managed during Test program opMode = Error / F27
25 Time Out UserIOTest
_WHTeststep UIOTest
User did not press all push buttons duringthe UserIOTest step of the Factory Test program
opMode = Error / F25
28 Tapped fieldfailure
_WHTeststepMotorTest
Motor is not able toactivate the tapped fieldrelay
opMode = Error / F28
** RESET the display by STOP/Cancel but not the flag.The digits are indicating the failure code without flashing. – The Dots are flashing alternatively with a period of 1 second
Electrical Diagram
Door Lock
on / off
VWIF
SMPS GND
12V
DP
Control Unit
M7 DP2DSS3 IF2
1 2 1 2 3
Vcc
1 2 1
J021 1
VW3
3 1
R T
Motor
PR2
43
Pressoswitch frontloader/toploader
PRS2
21
11
1614
12
8
VPW
31
VPW3
Valve Prewash
HE NTC
SET2 HE2
1 22 1
Vcc
7
Valve Main Wash
Drain Pump
DU3
3 1
Drum Up
Vcc
AQS2
3 1
Aquastop
Vcc
User Module E1
UI4
1
...
PN8 1 8
ϑ
User Module E2, E3
MX12
1
...
Legend
AQS aquastop switchDP drain pumpDSS door safety switchHE heating elementIF interference filterM motor drivePR pressostatSM switch, mainsV valve, doubleVW valve, main wash
- 14 -
-15 -
Wash Cycle of Cotton 30,40
detergent chamber
normal program flow +
large load of Load Detect.
only for medium loadof Load Detectiononly for small loadof Load Detection
ECO/extra care
EASY IRONING
PREWASH
w a t
e r
10 min10 min
37 min
22 min
75 min
pump(N1 + 30 sec)
door lock
more water,softer spinning
main washmain wash
Tsel-10 °C but 30 °C and 20 °C remain/+10 min
10 min
10 min
softer spinningmore water,softer spinning
morewater
e e p s d
rutarepmet
epoti
nos
level
max
`first 10s prewash then
main wash
10 min
6 min
first 10sprewash then
softenermain wash
18 min6 min
18 min
INTENSIVE RINSE
RINSE HOLDNo drain and spin
twice
Wash Phase prewash enzym phase main wash 1st rinse 3rd rinse spinning
2nd rinse (twice, if Intensive
Rinse selected, not used for small
and medium load of Load
Detection)
6 min10 min
6 min10 min
10 min18min
reversing period=16 sec10...14sec ON/6...2 sec OFF
40-54
N1
Tsel
40°C30°C
cool dow n (till 60°C, max. 45 sec) rinse hold
pre-extraction
peaks+final spin960rpm
ca. 14min
848rpm310 sec
848rpm310 sec
848rpm310 sec
-16 -
Wash Cycle of Cotton 95
detergent chamber
normal program flow +
large load of Load Detect.
only for medium loadof Load Detectiononly for small loadof Load Detection
ECO/extra care
EASY IRONING
PREWASH
w a t
e r
10 min17 min
28 min
28 min
38 min
pump(N1 + 30 sec)
door lock
more water,softer spinning
main washmain wash
Tsel-10 °C but 30 °C and 20 °C remain/+10 min
17 min
10 min
softer spinningmore water,softer spinning
morewater
e e p s d
rutarepmet
epoti
nos
level
max
`first 10s prewash then
main wash
17 min
6 min
first 10sprewash then
softenermain wash
18 min6 min
18 min
INTENSIVE RINSE
RINSE HOLDNo drain and spin
twice
Wash Phase prewash enzym phase main wash 1st rinse 3rd rinse spinning
2nd rinse (twice, if Intensive
Rinse selected, not used for small
and medium load of Load
Detection)
6 min10 min
6 min10 min
10 min18min
reversing period=16 sec10...14sec ON/6...2 sec OFF
608
rpm
280
sec40-54
N1
Tsel
40°C30°C
cool dow n (till 60°C, max. 45 sec) rinse hold
pre-extraction
peaks+final spin
960rpmca.
14min
400rpm280sec
848
rpm
280
sec
-17 -
Wash Cycle of Cotton 60
detergent chamber
normal program flow +
large load of Load Detect.
only for medium loadof Load Detectiononly for small loadof Load Detection
ECO/extra care
EASY IRONING
PREWASH
w a t
e r
18 min17 min
31 min
21 min
100 min
pump(N1 + 30 sec)
door lock
more water,softer spinning
main washmain wash
Tsel-10 °C but 30 °C and 20 °C remain/+10 min
17 min
18 min
softer spinningmore water,softer spinning
morewater
e e p s d
rutarepmet
epoti
nos
level
max
`first 10s prewash then
main wash
17 min
12 min
first 10sprewash then
softenermain wash
18 min12 min
18 min
INTENSIVE RINSE
RINSE HOLDNo drain and spin
twice
Wash Phase prewash enzym phase main wash 1st rinse 3rd rinse spinning
2nd rinse (twice, if Intensive
Rinse selected, not used for small
and medium load of Load
Detection)
12 min18 min
9 min18 min
10 min18min
reversing period=16 sec10...14sec ON/6...2 sec OFF
40-54
N1
Tsel
40°C30°C
cool dow n (till 60°C, max. 45 sec) rinse hold
pre-extraction
peaks+final spin
960rpm
ca. 14min
848rpm310sec
848rpm310sec
848rpm310sec
- 18 -
Wash Cycle of Synthetic
Wash Phase
detergent chamber
SYNTHETIC
RINSE HOLD
INTENSIVE RINSE
door lock
pump (N1+30 sec)
14 min
main wash
level
1st rinse
8 min8 min
main wash
spinning prewash enzym phase main wash 2nd rinse 3rd rinse
40 - 54 rpm
spee
d w
ater
te
mpe
ratu
re
N1
reversing period = 16 sec10...12 sec ON / 6...4 sec OFF 960
first 10 s prewash then main wash
first 10 s prewash then
softener
Tsel
40°C30°C
Opt
ion
40 min 5 min
No drain and spin
rpm220sec
960rpm220sec
prewash main wash
8 min
ECO
EASY IRONING
PREWASH
Tsel-10°C but 30 and 20°C remain/+10 min
more water, softer spinning
more water, softer spinning
more water
softer spinning
18 min 10 min
rinse holdcool dow n (till 45°C, max. 45 sec)
960 rpmpre-extraction
peaks+final spin 960rpm330sec
twice
-19 -
Wash Cycle of Delicate
Wash Phase
detergent chamber
DELICATE
RINSE HOLD
10 min
door lock
pump (N1+30 sec)
11 min
main wash
level
1st rinse
8 min3 min
main wash
spinning prewash enzym phase main wash 2nd rinse 3rd rinse
40 - 54 rpm
spee
d w
ater
te
mpe
ratu
re
N1
rinse hold
first 6 l prewash then main wash
first 10 s prewash then
softener
40°C30°C
Opt
ion
11 min 3 min
960 rpm reversing period = 16 sec
mainly 5 sec ON / 11 sec OFF
prewash main wash
3 min
PREWASH 18 min
0
pre-extraction
peaks+final spin
960rpm
330sec
No drain and spin
-20 -
Wash Cycle of Quick Wash
Wash Phase
detergent chamber
Express
RINSE HOLD
door lock
pump (N1+30 sec)
2 min
main wash
level
1st rinse
10 min4 min
main wash
spinningprewash enzym phase main wash 2nd rinse 3rd rinse
40 - 54 rpm
spee
dw
ater
tem
pera
ture
N1
reversing period = 16 sec10...14 sec ON / 6...2 sec OFF 400
rpm60sec
752rpm60sec
rinse hold
first 10 s prewash then main wash
first 10 s prewash then
softener
Tsel
40°C30°C
Opt
ion
10 min 3 min
No drain and spin
no cool dow n
pre-extracti
onpeaks+final spin960rpm
- 21 -
Wash Cycle of Daily Wash
Wash Phase
detergent chamber
Crono
RINSE HOLD
INTENSIVE RINSE
door lock
pump (N1+30 sec)
10 min
main wash
level
20 min
1st rinse
11 min7 min
main wash
spinning
7 min 6 min
prewash enzym phase main wash 2nd rinse 3rd rinse
40 - 54 rpm
spee
dw
ater
tem
pera
ture
N1
reversing period = 16 sec
752rpm120sec
848rpm
120sec
rinse hold
first 10 s prewash then main wash main wash first 10 s
prewash then softener
Tsel
40°C30°C
pre-extractionpeaks+
final spin 960rpm460sec
Opt
ion
twice
No drainand spin
10...14 sec ON / 6...2 sec OFF
-22 -
H S A W D N A H d n a L O O W f o s e l c y C h s a W
e s a h P h s a W
rebmahc tnegreted
L O O W
H S A W D N A H
hsaw niam neht hsawerp l 6 tsif
n i m 24
n i m 4 n i m 20
n i m 4
spee
d w
ater
te
mpe
ratu
re
k c o l r o o d
) c e s 0 3 + 1 N ( p m u p
g n i n n i p s e s n i r d r 3 e s n i r d n 2
hsaw niamhsaw niam
e s n i r t s 1 h s a w n i a m
l e v e l
nim 20
n i m 42
n i m 2
n i m 2 n i m 4
m p r 0 4
m p r 0 6 9
c e s 2 3 = d o i r e p g n i s r e v e r FFO s13 / NO s1 ylniam .looW
960
rpm
90sec
1 N
d l o h e s n i r
dloh esnir
m p r 4 5
for HANDWASH:
only 400rpm possible for Wool: 960 rpm possible
first 10 s prewash then
softener
T max: WOOL/ HW: 40°C SILK: 30°C
30°C 40°C
No drain and spin
HANDWASH 1s ON / 63s OFF