services for the wastewater reclamation project's phase i
TRANSCRIPT
Delivered By:Tiffany Hilborn
Business Developmenttiffany@ctesouth. com
619) 453-1393
CTE South, Inc. 14538 Meridian Parkway, Suite A
Riverside, CA 92518
Proposal for Soils and Materials TestingServices for the Wastewater Reclamation
Project' s Phase I, Package C and D CollectionSystem Construction
Table of ContentsPart 1 – Insurance Requirements .................................................................................................................. 2
Part 2 – Professional Services Agreement Comments .................................................................................. 6
Part 3 – Exhibit “A” Soils and Materials Testing Davis Bacon Prevailing Wage Fee Schedule ...................... 8
Part 4 – Statement of Offer and Signature ................................................................................................... 14
Hi-Desert Water District – Proposal # R180292
Part 1 – Insurance Requirements
Hi-Desert Water District – Proposal # R180293
Hi-Desert Water District – Proposal # R180294
Hi-Desert Water District – Proposal # R180295
Hi-Desert Water District – Proposal # R180296
Part 2 – Professional Services Agreement Comments
Hi-Desert Water District – Proposal # R180297
CTE South, Inc. has no exceptions to this proposal.
Hi-Desert Water District – Proposal # R180298
Part 3 – Exhibit “A” Soils and Materials Testing Davis Bacon PrevailingWage Fee Schedule
Hi-Desert Water District – Proposal # R180299
Hi-Desert Water District – Proposal # R1802910
We are fully capable of providing all of the proposed services from our facilities in Riverside, andEscondido, California. While considering our proposal please keep in mind that no additionalcharges for travel or mileage will be added.
All applicable services will be performed pursuant to current prevailing wage rates under theCalifornia Labor Code. Please note that all inspector and technician rates may increase everyJuly 1, commensurate with the State of California annual increase and with District approval.
PROFESSIONAL ENGINEERING STAFF
Senior Engineer / Geologist / Architect
Licensed Land Surveyor
Project Engineer / Geologist
Environmental Consultant / Registered Environmental Assessor
Staff Engineer / Geologist / Architect
One-Man Survey Crew & Equipment
Two-Man Survey Crew & Equipment
Three-Man Survey Crew & Equipment
Survey Technician
QSP Services
INSPECTION SERVICES & QUALITY CONTROL
Concrete Technician ( ACI)
Pile Driving Inspector / Deep Foundation Inspector
Mechanical / Electrical / Plumbing Inspector
Roofing / Waterproofing Inspector
Roofing / Waterproofing Consultant
Inspector of Record / DSA / OSHPD Inspector
Quality Control Representative
Submittal Reviewer
QC Plan Preparation
NON-DESTRUCTIVE TESTING SERVICES
Non-Destructive Testing Inspector ( Ultrasonic, magnetic particle, dye penetrate)
Metallic Surface Coatings (Paint or Itumescescent Fireproofing)
Radiographic ( low power portable and laboratory available)
SPECIAL SERVICES
Vertical Coring / Sawing Operator & Equipment (Horizontal extra)
Floor Flatness Testing
Reinforcing Steel Location
Anchor Pull Tests - up to 30 tons
Batch Plant Inspector
Procedure Qualification per AWS, ASME or Military Standards
SUPPORT SERVICES
Certificate of Completion
Draftsman
Express Mail (FEDEX/UPS) (minimum)
Facsimile (each page)
File Search, re-issue of report, copies ( minimum)
Pickup/Delivery ( 50 mile radius of CTE office)
Certified Payroll (per hour)
Sample Pick-up
Sample Pick-up (Large)
Schedule of Fees and Services
110
100
100
QUOTE
Senior Soil Technician $ 95
Principal Engineer / Geologist
CAD Technician
Soil Technician
230
95
85
90
1
40
250
Wage Rate
130
100
90
295
95
95
QUOTE
100
85
QUOTE
85
150
130
110
180
100
95
100
90
Prevailing
80
50
65
45 / Trip
65 / Trip
Registered Special Inspector (Concrete, Masonry, Welding, Pre-Stress, Fireproofing)$ 95
QUOTE
200
QUOTE
QUOTE
90
Hi-Desert Water District – Proposal # R1802911
Other
Method Used
CTM 312
UBC 18- 2
CTM 216
CTM 216
CTM 301
CTM 643
CTM 217
AGGREGATES
CTM 227
CTM 205
CTM 229
CTM 229
CTM 211
Price ASTM
Designation
D422
per Specimen
Laboratory - Schedule of Fees and Services
Test Procedure
Consolidations - Per Point $ 200 D2435
Direct Shear Test $ 195 to $245 D3080
Expansion Index $ 150 D4829
Hydrometer ( Particle Size Analysis) $ 180
D1557 / D698
Laboratory Compaction Test - 4" or 6" Mold Requiring Rock Correction
SOILS
California Bearing Ratio (CBR)$ 360 D1883
Cement Treated Base, Laboratory Design - Soil Cement, Each Set $ 530 D558 / D1633
Cement Treated Base, Laboratory Compaction ( Moisture Density- Each Curve) $ 275 D558
Cement Treated Base, Sample Fabrication & Compression- Per Point $ 85 D558 / D1633
Chloride Content of Soil $ 70 ---
Laboratory Compaction Test - 4" Mold (Moisture Density- Each Curve) $ 175 D1557 / D698
Laboratory Compaction Test - 6" Mold (Moisture Density-Each Curve) $ 190
225 D1557 / D4718
Moisture Content $ 25 D2216
Moisture & Density $ 40 D2937
No. 200 Sieve Wash $ 60 D1140
Plasticity Index / Liquid Limit/Atterburg Limits $ 120 D4318
Permeability Test - Constant Head
Fine Grained Soil $ 210 D5084
Granular Soil $ 350 D2434
R - Value (Minimum 3 pts.)$ 240 D2844
Resistivity and pH of Soil $ 150 D4972
Sand Equivalent $ 100 D2419
Shrinkage Limit $ 90 D427
Soil Classification w/ Atterburg & Gradation $ 245 D2487
Sulfate Content of Soil $ 80 ---
Organic Content (Organic Burn)$ 65 D2974
Aggregate Conformance Testing for State of California Projects $ 220 ---
Includes: Sieve Analysis, Specific Gravity, No. 200 Wash, Organic Impurities, Unit Weight)
Clay Lumps and Friable Particles $ 90 C142
Cleanness Value $ 80 ---
Crushed Particles, Percent $ 120 ---
Durability Index, Coarse Aggregate $ 110 D3744
Durability Index, Fine Aggregate $ 100 D3744
Los Angeles Rattler $ 160 C131 or C535
Organic Impurities in Sand $ 50 C40
Sieve Analysis (Gradation), Coarse Aggregate $ 60 C136
Sieve Analysis (Gradation), Fine & Coarse Aggregate ( Including 200 Wash)$ 80 C136
Unit Weight per Cubic Foot, Voids in Aggregate $ 60 C29
Specific Gravity & Absorption, Fine Aggregate $ 70 C128
Specific Gravity & Absorption, Coarse Aggregate $ 60 C127
Sodium Sulfate Soundness ( Per Size Fraction)$ 70 C88
Hi-Desert Water District – Proposal # R1802912
Other
Method Used
ASPHALT CONCRETE
CTM 382
CTM 382
CTM 304, 308, 366
CTM 308
CONCRETE
MASONRY
Compression Test, Brick ---
UBC 21- 17
UBC 21- 17
Compression Test, CMU Block (Full Size or Coupon)---
UBC 21-18
UBC 21-16
UBC 21- 6
Linear Shrinkage ---
CBC Title 24
80
Compression Tests, Mortar, 2x4" cylinder
Modulus of Rupture, Brick
25
50
Absorption Test, Brick
60AbsorptionTest, CMU Block
50
C495$50UnitWeight, Lightweight Concrete Fill
Compression Tests, Grout
C67
C6740
Compression Tests, 6x12" Cylinder $ 20 C39
C78
C42 / C1604
C42 / C1604
C495
100
C39 / C780
C1019$25
50
C67
C67
C1314
C1314
C140 / C90
C426
D6307
Trial Batch, Includes Mix Design, Aggregate Testing & Six Compression Tests
Shear Test, Core (Excludes Sample Preparation)
Saturation Co-Efficient ( Includes Absorption) Brick
C67$25Moistureas Received, Brick
100
In-Place Shear Test (per test)
Efflorescence, Block & Brick
C90$400ConformancePackage
30
Compression Tests, High Strength Grout/ Mortar Cube ( 2x2")
C140 / C90$50
C109
20
C-90 / C67
110
C157 (Mod)
95CompressionTest, Composite Prism (Half Size 8 x 16 x 8")
45
Compression Test, Composite Prism (Full Size 8 x 16 x 16")
Modulus of Elasticity, Static C469
200DryingShrinkage (3 Specimens-28 Days)
QUOTE
750
C496$90SplittingStrength Test - Concrete Cylinders
85
QUOTEConcreteMix Design
80ConcreteFlexural Test, 6x6x18" Flex Beam
Concrete Mix Design (Hourly by Engineer)
Compression Tests, Lightweight Concrete Fill
60CompressionTests, Core - Shotcrete/Concrete/Gunite ( Includes Sample Preparation)
175CompressionTests, Cores - Shotcrete/Gunite Panels, ( 3 Cut Cores per Panel)
C39$18CompressionTests, 4X8" Cylinder
Hveem Stability & Unit Weight $ 160 D1560 / D1561
Asphalt Mix Design QUOTE Marshall & Hveem
Asphalt Mix Design Review $ 150 ---
Unit Weight Compacted Sample or Core ( Bulk Specific Gravity)$ 60 D2726
Laboratory - Schedule of Fees and Services
Test ProcedurePrice ASTM
per Specimen Designation
Marshall Stability, Flow & Unit Weight ( Three Specimens)$ 160 D6926 / D6927
Maximum Theoretical Unit Weight (Rice Specific Gravity)$ 150 D2041
Tensile Strength Ratio (TSR)$ 500 D4867
Extraction, % Asphalt (Including Gradation of Extracted Aggregate)$ 150 D6307 / D5444
Extraction, % Asphalt $ 70
Hi-Desert Water District – Proposal # R1802913
OtherMethod Used
STEEL ( 7/8" Dia.) (1" - 1 ¼")
145 $ 230 ---
60 $ 60 ---
60 $ 90 ---
50 $ 80 ---
35 $ 60 ---
Mechanically Spliced Reinforcing Steel ---
Oven Dry Method UBC 7-6
Asbestos Evaluation ( per ply)---
Asphalt Softening Point ---
Roofing Material Analysis, With Surfacing ---
Roofing Material Analysis, Without Surfacing ---
Roofing Tile, Absorption ( set of 5)---
Roofing Tile, Strength Test (set of 5)---
American Welding Society ( AWS D1.1)---
Limited Thickness Plate (per position)---
Unlimited Thickness Plate ( per position)---
Pipe (per position)---
American Welding Society ( AWS D1. 4)---
Bar Sizes #3 through #9 (each)---
Bar Sizes #10 through #11 (each)---
Bar Sizes #14 through #18 (each)---
American Society of Mechanical Engineers ( ASME)---
Plate or Pipe Procedure Qualification ( each)---
Plate or Pipe Welder Qualification (each)---
American Welding Society (AWS D1.3)---
Light Gauge Metal (includes butt and plug weld)---
Procedure Qualification per AWS, ASME or Military Standards ---
Fillet Weld Test (Break and Etch Test)---
Fillet Weld Test Plates ---
Ultrasonic Testing of Weld Coupons ---
Witness time, If Required --- 100 ---
Reinforcing Steel, Bend Test - No. 14 Bars
Structural Steel, Tensile Test - Up to 200, 000 lbs.
Reinforcing Steel, Bend Test - No. 11 Bars & Smaller
Welded Specimens, Tensile Testing - Mechanically Spliced Bar
40
35
30
32
80
30
60 ---
75
230
250
ASTM
A615 / A706
Laboratory - Schedule of Fees and Services
F606 / A325 / A490
150
High Strength Bolt, Nut - Proof Load
Reinforcing Steel, Tensile Test - No. 11 Bars & Smaller
Reinforcing Steel, Tensile Test - No. 14 Bars & Larger ( To Min. Requirement Only)
High Strength Bolt, DSA Conformance ( Bolt=Wedge Tensile, Proof Load= Nut & Bolt)
A 370
80WeldedSpecimens, Tensile Test - No. 18 Bars ( To Min. Require. Only)
WELDING CERTIFICATION
150
ROOFING
80
D 3617$225
D 2829
per Specimen
35 A615 / A706
100
QUOTE
200
550
550
230
230
180
A615 / A706
F606 / A325 / A490
F606 / A563
50
60
150
200
50
450
180 ---
E 605
50
A615 / A706
Welded Specimens, Tensile Test - No. 11 Bars & Smaller
Mechanical Tests, Hardness Test, Rockwell ( Includes Nut, Bolt, & Washer)
Welded Specimens, Tensile Test - No. 14 Bars
Structural Steel, Bend Test.
Structural Steel, Pipe Flattening Test
High Strength Bolt, Bolt - Proof Load
50
High Strength Bolt, Bolt - Wedge Tensile Strength
High Strength Bolt, Bolt - Axial Tensile Strength
145
Spray Applied Fireproofing Density Tests
Prestressed Steel, Tensile Test, Strand ( 7 wire)
Designation
E18
F606 / A325 / A490
F606 / A325 / A490
Test ProcedurePrice
Hi-Desert Water District – Proposal # R1802914
Part 4 – Statement of Offer and Signature
Hi-Desert Water District – Proposal # R1802915
This proposal, as validated below, is a firm offer for a period of 90 -days upon submission to the Hi-DesertWater District.
Sincerely,
CTE, SOUTH, INC. State DIR - 2017 SB 845 Registration # 1000006124
Vince J. Patula, PG, CEG #2057 Tiffany HilbornSenior Engineering Geologist / Branch Manager Business Developmentvince@ctesouth. com tiffany@ctesouth. com
619) 453-1393
Hi-Desert Water District – Proposal # R1802916
Hi-Desert Water District – Proposal # R1802917