

2

About This cument:

This document is intended to regulate the site installation documents at each step of a microwave project

specify the quantity and format of output documents at each phase and provide guide lines on the integrity

and specification of output documents.



3

Table of Contents

Link Budget.......................................................................................................................... 4

Board Plan ........................................................................................................................... 5

Media Plan .......................................................................................................................... 5

SW Commissioning ............................................................................................................. 6

HW Installation Pictures ................................................................................................... 08

MW Installation Check list ................................................................................................ 11

Confirmation Check List …………………………………………………………………………………………..….15

1- Link Budget

Designed RSL: -39.24(dBm) Tx Power: 20.0(dBm)

Achieved RSL: -41.2(dBm) Tx Frequency:15047.0/ 14557.0(MHz)



4

S-KHI-0078 S-KHI-0390

Elevation (m) 63.67 46.31 Latitude 24 55 39.10 N 24 56 32.30 N

Longitude 067 07 50.40 E 067 11 57.30 E True azimuth (°) 76.69 256.72 Vertical angle (°) -0.16 0.12

Antenna model A15D12HS A15D12HS Antenna height (m) 25.00 25.00 Antenna gain (dBi) 42.60 42.60

Circ. branching loss (dB) 3.60 3.60

Frequency (MHz) 15000.00 Polarization Vertical

Path length (km) 7.12

Free space loss (dB) 133.04 Atmospheric absorption loss (dB) 0.20 Field margin (dB) 1.00

Net path loss (dB) 56.24 56.24

Radio model 15G_HP_128Q_28M_159M 15G_HP_128Q_28M_159M TX power (watts) 0.10 0.10 TX power (dBm) 20.00 20.00

EIRP (dBm) 59.00 59.00 Emission designator 28M0D7W 28M0D7W

TX Channels 24B28H 15047.0000H 24B28L 14557.0000H 24B28H 15047.0000V 24B28L 14557.0000V

RX threshold criteria BER 10-6 BER 10-6 RX threshold level (dBm) -70.00 -70.00

RX signal (dBm) -39.24 -39.24 Thermal fade margin (dB) 33.76 33.76 XPD fade margin - multipath (dB) 29.07 29.07 Flat fade margin - multipath (dB) 27.80 27.80

Geoclimatic factor 1.53E-03 Path inclination (mr) 2.44

Fade occurrence factor (Po) 6.49E-03 Average annual temperature (°C) 26.00

Worst month - multipath (%) 99.99892 99.99892 (sec) 28.35 28.35

Annual - multipath (%) 99.99960 99.99960 (sec) 127.58 127.58

(% - sec) 99.99919 - 255.16

Rain region ITU Region K 0.01% rain rate (mm/hr) 42.00

XPD fade margin - rain (dB) 41.10 41.10 Flat fade margin - rain (dB) 33.03

Rain rate (mm/hr) 128.25 Rain attenuation (dB) 33.03 Annual rain (%-sec) 99.99964 - 112.06

Annual multipath + rain (%-sec) 99.99884 - 367.22

Tue, Jun 04 2013 S-KHI-0078-S-KHI-0390.pl4 Reliability Method - ITU-R P.530-12 Ran - ITU-R P530-7



5

2- Board Plan

Site ID: 0078

PIU-

10FAN-

11

7 CSH 8

5—IFX2->0390-V 6—IFX2->0390-H

PIU-

9

3—IFX2->0390-V 4—IFX2->0390-H

1- 2—SL1D

3- Media Plan

Route

Site ID Rout Site-1 Rout Site-2 Rout Site-3 Warid Tie

E1

4. SW Commissioning pictures

After completion of Hardware installation and Software commissioning following pictures will be required.

1. Software Commissioning (Pictures).

Main Window

(Select NE from NE Explorer >> Click Slot Layout

from main Window)

TX Frequency

(Select ODU from NE Explorer >> Click ODU

Interface>> Radio Frequency Attribute)



6

IF Attributes

(Select IF1A from NE Explorer >> Click IF

Attribute>> Radio Working Mode)

TX Power & RSL

(Select ODU from NE Explorer >> Click ODU

Interface>> Power Attribute)

N/A

Node Name & Node ID



7

(Select NE from NE Explorer >> Expend NE Configuration >> Click NE Attribute)

Cross Connections

(Please capture after expanding cross connections)

Protection (If applicable)

(Select NE from NE Explorer >>ExpendNE Configuration >> Click Cross connect Configuration)

N/A



8

5. MW Installation pictures

Antenna Fixing

(Must Cover antenna assembly while capturing)

ODU Fixing and waterproof

(Must cover both IF Connectors in case of 1+0)

ODU Grounding

(Show Grounding termination)

IF Cable grounding

(Show IF End)



9

IF Cable Grounding

(Show Bus Bar end)

IF Cable Grounding

(If Bus Bar installed)



10

MW Rack& DDF& DCDB

(Cover all Three in one frame) IF cableloop

(Near to ODU)



11

Cable Routing on Vertical Ladder

(Identify Recently Installed cable) IDU Grounding

(Cover termination end)

Near to tower brases use the mounting bracket bolts

in revarce path Use Of the labels for DC power breakers



12

DDF

(Identify Recently Installed cable with proper

labeling)

DCDB

(Cover your Cable connection at Breaker in right

sequence)

N/A N/A



13

Grounding cable should be routed & printed labeled Power cable should be routed & printed labeled

IF connector of ODU should be waterproofed and

face downward.

Mention the Faceing ID at both end



14

6- Microwave Installation Check List

Site Supervisor Name: Adnan Cell Number:03003672767

Signature: ____________________________ Date:_________26-09-2013___________________

mation

e ID (A) 0078 Site ID (B) 0390 Subcon Symbia

MW Design Detail Checklist

nk Type (PDH/SDH) PDH

Indoor Installations OK Not OK Remarks

19 inch Rack Installation N/A

ability of 19" Rack mounting and alignment as per drawing. N/A

oper Leveling and Drilling works N/A

oper tightening of all nuts and bolts and No nuts and bolts missing N/A

ounding Bus Bar Mounting & DCDB installation. N/A

IDU Check List



15

mly installed (Best suitable place) OK

ftware Check (using WEB LCT) OK

L Check & Snapshots (using WEB LCT) OK

tenuation Values & TX Power Check & Snapshots as per Link Budget OK

eck Far end Visibility (NMS) OK

oper IF Cable Connector & tightness OK

cuit Breakers of proper rating installed OK

Grounding

oper thimbles used at Grounding Bus Bar OK

rge Arrestors properly installed & grounded (If applicable) N/A

st OK Not OK Remarks

U properly grounded OK

'' rack properly grounded N/A

DF properly grounded N/A

Cable Laying/ Labeling

cables properly cut, laced and terminated OK

oper Routing of IF Cables, PCM Cables and Power Cables OK

Cables and Power Cables laid separately OK

Us properly labeled OK

e Tags used at IDU end for labeling OK

B and Circuit Breakers labeled OK

/ PCM/ Power Cables labeled OK

beling of E1 terminations done on DDFs N/A

utdoor Installations



16

Antenna/Mounting Works OK NOK Remarks

crowave Dish and Mounting Bracket installed properly OK

tra IF cable should be twisted to 2 or 3 circles near ODU/Antenna OK

oper weather proof taping at ODU/ Antenna side OK

tenna Water drain hole detaches rubber cap and drain hole must be at bottom OK

tenna height as per the link budget OK

Nuts and Bolts properly tightened OK

W Antenna Side Support properly mounted OK

tenna Pole Fixed Properly OK

tenna Bracket Fixed in Pole Properly OK

nnectors properly made and securely tightened OK

stec properly sealed N/A

Grounding OK NOK Remarks

oper thimbles used OK

DU properly grounded with scratched paint tower OK

Cables grounded with all outdoor bus bars available OK

ot more than one grounding termination on a single point on bus bars OK

Cable Laying/ Labeling

oper Routing of IF Cables OK

uminum tags used for labeling at ODU side for IF Cables N/A

grounding wires/ cables in downward direction from ODU/ IF Cables on tower OK

cables properly tied on tower OK

aveguide/IF cable termination (antenna to ODU/equipment side) OK

beling for each PCM cable and for each E1 N/A



17

Tests Performed

witch over function success N/A

/ Rx Mute function success OK

oopback success OK

ear-End loop back success OK

r-End loop back success OK

OW function success N/A

arm Generation and Reporting success OK

op visible on NMS OK

hours BERT Test N/A

tching of all E1s checked N/A

Items to be attached with Pre-PAT document OK NOK Remarks

Hours BERT Test Report N/A

nk Performance Report OK

ommissioning Documents OK

stallation Pictures (Indoor/Outdoor) OK

L & Configuration Snapshots (tx power, attenuation etc.) OK

ard Inventory Information OK

0- House Keeping

e properly cleaned OK



18

quipment Serial #

IDU ODU HYBRID DISHite A

ite B

REMARKS

TP done

7. Confirmation Check List

Item Description Yes No Remarks

Combine PR Received (BTS+MW) NO

Site RFI checked and confirmed to Project Team for

equipment delivery, NO

DN received before equipment delivery, Yes



19

Combine Equipment received at site (BTS+MW), YES

Link Budget, Board plan & Media plan was shared before

team movement, YES

Missing Equipment reported timely YES

site compeletion report 0078

Documents