size and performance summary glazing performance grille ......sliding window – triple-pane...
TRANSCRIPT
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-1
350 Series Sliding Window
Size and Performance Summary
Glazing Performance
Grille Profiles and Patterns
Size Tables
Design Data
Detailed Product Description
Cross Sections
The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are
subject to change without notice. Consult your local Pella representative for up-to-date product information.
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-2
350 Series Sliding Window
Sizes
Standard Sizes S
Special Sizes Available Built on 1/8" Increments O
Frames
Nail Fin Only O
Nail Fin with J-Channel O
4-1/2" Block S
3-1/4" Block Pocket Install / Replacement S
Double-Wall Flush Flange O
Integral 5/8" Flange O
Performance 1Standard Performance
Meets or Exceeds AAMA / WDMA RatingsLC-PG40
Hallmark Certified
Air Infiltration 2(cfm / ft2 of frame @ 1.57 psf wind pressure.)
0.06
Design Pressure 40 psf
Water Penetration Resistance 6.06 psf
Other Performance Criteria
Forced Entry Resistance (Minimum Security Grade) 3 10
Operating Force (lb) Initiate Motion / Maintain Motion (of Hallmark tested size and glazing) 4
50 / 35
S = Standard; O = Optional
(1) Published performance data is for single unit only. See Design Data pages in this section for specific product performance class and grade values. Performance with additional options may not
be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
(2) Published performance Data for air infiltration is determined by testing a minimum of four (4) products of NFRC model size. Testing is conducted in accordance with ASTM E283. Air infiltration
ratings for products will differ by size. The performance data does not apply to combination assemblies unless notes. Actual product performance may vary for a number of reasons including
installation and product care.
(3) The higher the level, the greater the product's ability to resist forced entry.
(4) Glazing configurations may result in higher operational forces.
(5) ASTM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration.
The presence of low-E or argon have negligible effect on sound attenuation characteristics.
Size and Performance Data
Sound Transmission Class / Outdoor-Indoor Transmission Class
Frame Size Tested 5
Glazing SystemSTC
RatingOITC
RatingOverall Glazing Thickness
Exterior Glass Thickness
Interior Glass Thickness
Third Pane Thickness
Sliding Window - Dual-Pane Insulating Glass
60" x 48" 11/16" 3 mm 3 mm — 28 22
60" x 48" 11/16" 3 mm 5 mm — 32 26
Sliding Window – Triple-Pane Insulating Glass
60" x 48" 1-1/4" 3 mm 3 mm 3 mm 29 23
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-3
350 Series Sliding Window
S = Standard; O = Optional
(1) Not available with triple-pane glazing.
(2) Contact your local Pella sales representative for current offering.
Glazing (insulating glass)
Glazing Type
Dual-pane insulating glass S
Triple-pane insulating glass O
Insulated Glass Options / Low-E Types
Advanced Low-E S
NaturalSun Low-E O
SunDefense™ Low-E 1 O
Gray Low-E 1 O
Bronze-tinted Advanced Low-E 1 O
Additional Glazing Options
Annealed glass S
Tempered glass O
Obscure glass 2 O
Noise reduction glass (STC 3 mm / 5 mm combination) 1 O
Gas Fi l l / High Alt i tude
Argon S
High altitude O
High altitude with argon 1 O
Sash
Foam Insulation O
Interior / Exterior color
White Interior/White Exterior S
Almond Interior/Almond Exterior O
White Interior/Brown Exterior O
White Interior/Fossil Exterior O
White Interior/Black Exterior O
White Interior/Brick Red Exterior O
White Interior/Hartford Green Exterior O
White Interior/Morning Sky Gray Exterior O
White Interior/Poplar White Exterior O
White Interior/Portobello Exterior O
White Interior/Tan Exterior O
Hardware
Color matched hardware S
Bright Brass, Satin Nickel or Oil-Rubbed Bronze O
Sash Locks
Standard Cam Lock S
Autolock O
Features and Options
Screens
Conventional black fiberglass screens - flat SInView™ screens O
Grilles
Gri l les-Between-the-Glass 3/4" Contour O1" Contour OGrille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided
O
Simulated-Divided-Light Gri l les 1 (without spacer)7/8" contour profile O
Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided
O
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-4
350 Series Sliding WindowG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 11/16" Dual-Pane with 3mm Glass N NC SC S CA11/16" Advanced Low-E IG PEL-N-192-00933-00001 3 3 Air 0.31 0.29 0.53 56
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00933-00002 0.31 0.26 0.47 56
with 7/8" Simulated Divided Light grilles PEL-N-192-00933-00003 0.31 0.26 0.47 56
11/16" Advanced Low-E IG PEL-N-192-00934-00001 3 3 Argon 0.27 0.28 0.53 59 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00934-00002 0.27 0.25 0.47 59 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00934-00003 0.27 0.25 0.47 59 N NC SC S
11/16" NaturalSun Low-E IG PEL-N-192-00913-00001 3 3 Air 0.32 0.52 0.60 55
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00913-00002 0.32 0.47 0.53 55
with 7/8" Simulated Divided Light grilles PEL-N-192-00913-00003 0.32 0.47 0.53 55
11/16" NaturalSun Low-E IG PEL-N-192-00914-00001 3 3 Argon 0.28 0.52 0.60 59 N 34 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00914-00002 0.28 0.47 0.53 59 N
with 7/8" Simulated Divided Light grilles PEL-N-192-00914-00003 0.28 0.47 0.53 59 N
11/16" SunDefense™ Low-E IG PEL-N-192-00947-00001 3 3 Air 0.31 0.21 0.49 56 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00947-00002 0.31 0.19 0.44 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00947-00003 0.31 0.19 0.44 56 S
11/16" SunDefense Low-E IG PEL-N-192-00948-00001 3 3 Argon 0.27 0.21 0.49 60 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00948-00002 0.27 0.19 0.44 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00948-00003 0.27 0.19 0.44 60 N NC SC S
Vent — with Foam Inserts11/16" Advanced Low-E IG PEL-N-192-00891-00001 3 3 Air 0.31 0.29 0.53 56
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00891-00002 0.31 0.26 0.47 56
with 7/8" Simulated Divided Light grilles PEL-N-192-00891-00003 0.31 0.26 0.47 56
11/16" Advanced Low-E IG PEL-N-192-00892-00001 3 3 Argon 0.27 0.28 0.53 59 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00892-00002 0.27 0.25 0.47 59 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00892-00003 0.27 0.25 0.47 59 N NC SC S
11/16" NaturalSun Low-E IG PEL-N-192-00871-00001 3 3 Air 0.31 0.52 0.60 55
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00871-00002 0.31 0.47 0.53 55
with 7/8" Simulated Divided Light grilles PEL-N-192-00871-00003 0.31 0.47 0.53 55
11/16" NaturalSun Low-E IG PEL-N-192-00872-00001 3 3 Argon 0.28 0.52 0.60 59 N 34 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00872-00002 0.28 0.47 0.53 59 N
with 7/8" Simulated Divided Light grilles PEL-N-192-00872-00003 0.28 0.47 0.53 59 N
11/16" SunDefense™ Low-E IG PEL-N-192-00905-00001 3 3 Air 0.30 0.21 0.49 56 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00905-00002 0.30 0.19 0.44 56 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00905-00003 0.30 0.19 0.44 56 NC SC S
11/16" SunDefense Low-E IG PEL-N-192-00906-00001 3 3 Argon 0.26 0.21 0.49 60 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00906-00002 0.26 0.19 0.44 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00906-00003 0.26 0.19 0.44 60 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-5
350 Series Sliding WindowG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 11/16" Dual-Pane with 3mm / 5mm Glass N NC SC S CA11/16" Advanced Low-E IG PEL-N-192-00935-00001 5 3 Air 0.33 0.28 0.53 54
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00967-00001 0.34 0.25 0.47 54 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00935-00002 0.33 0.25 0.47 54 S
11/16" Advanced Low-E IG PEL-N-192-00936-00001 5 3 Argon 0.28 0.28 0.53 58 NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00968-00001 0.30 0.25 0.47 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00936-00002 0.28 0.25 0.47 58 NC SC S
11/16" NaturalSun Low-E IG PEL-N-192-00915-00001 5 3 Air 0.33 0.50 0.60 54
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00963-00001 0.35 0.45 0.53 54
with 7/8" Simulated Divided Light grilles PEL-N-192-00915-00002 0.33 0.45 0.53 54
11/16" NaturalSun Low-E IG PEL-N-192-00916-00001 5 3 Argon 0.29 0.50 0.60 57 N
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00964-00001 0.31 0.45 0.53 57
with 7/8" Simulated Divided Light grilles PEL-N-192-00916-00002 0.29 0.45 0.53 57 N
11/16" SunDefense™ Low-E IG PEL-N-192-00949-00001 5 3 Air 0.32 0.22 0.49 54 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00971-00001 0.34 0.20 0.43 54 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00949-00002 0.32 0.20 0.43 54 S
11/16" SunDefense Low-E IG PEL-N-192-00950-00001 5 3 Argon 0.28 0.21 0.49 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00972-00001 0.29 0.19 0.43 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00950-00002 0.28 0.19 0.43 58 NC SC S
Vent — with Foam Inserts11/16" Advanced Low-E IG PEL-N-192-00893-00001 5 3 Air 0.32 0.28 0.53 54
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00957-00001 0.34 0.25 0.47 54 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00893-00002 0.32 0.25 0.47 54 S
11/16" Advanced Low-E IG PEL-N-192-00894-00001 5 3 Argon 0.28 0.28 0.53 58 NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00958-00001 0.29 0.25 0.47 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00894-00002 0.28 0.25 0.47 58 NC SC S
11/16" NaturalSun Low-E IG PEL-N-192-00873-00001 5 3 Air 0.33 0.50 0.60 54
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00953-00001 0.34 0.45 0.53 54
with 7/8" Simulated Divided Light grilles PEL-N-192-00873-00002 0.33 0.45 0.53 54
11/16" NaturalSun Low-E IG PEL-N-192-00874-00001 5 3 Argon 0.29 0.50 0.60 57 N
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00954-00001 0.30 0.45 0.53 57 N
with 7/8" Simulated Divided Light grilles PEL-N-192-00874-00002 0.29 0.45 0.53 57 N
11/16" SunDefense™ Low-E IG PEL-N-192-00907-00001 5 3 Air 0.32 0.22 0.49 54 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00961-00001 0.33 0.20 0.43 54 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00907-00002 0.32 0.20 0.43 54 S
11/16" SunDefense Low-E IG PEL-N-192-00908-00001 5 3 Argon 0.27 0.21 0.49 58 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00962-00001 0.29 0.19 0.43 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00908-00002 0.27 0.19 0.43 58 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-6
350 Series Sliding WindowG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 1" Dual-Pane with 5mm Glass N NC SC S CA1" Advanced Low-E IG PEL-N-192-00937-00001 5 5 Air 0.31 0.28 0.52 56
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00937-00002 0.31 0.25 0.46 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00937-00003 0.31 0.25 0.46 56 S
1" Advanced Low-E IG PEL-N-192-00938-00001 5 5 Argon 0.28 0.27 0.52 59 NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00938-00002 0.28 0.25 0.46 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00938-00003 0.28 0.25 0.46 59 NC SC S
1" NaturalSun Low-E IG PEL-N-192-00917-00001 5 5 Air 0.32 0.50 0.59 55
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00917-00002 0.32 0.45 0.52 55
with 7/8" Simulated Divided Light grilles PEL-N-192-00917-00003 0.32 0.45 0.52 55
1" NaturalSun Low-E IG PEL-N-192-00918-00001 5 5 Argon 0.29 0.50 0.59 59 N
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00918-00002 0.29 0.45 0.52 59 N
with 7/8" Simulated Divided Light grilles PEL-N-192-00918-00003 0.29 0.45 0.52 59 N
1" SunDefense™ Low-E IG PEL-N-192-00951-00001 5 5 Air 0.31 0.21 0.48 56 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00951-00002 0.31 0.19 0.43 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00951-00003 0.31 0.19 0.43 56 S
1" SunDefense Low-E IG PEL-N-192-00952-00001 5 5 Argon 0.28 0.21 0.48 60 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00952-00002 0.28 0.19 0.43 60 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00952-00003 0.28 0.19 0.43 60 NC SC S
Vent — with Foam Inserts1" Advanced Low-E IG PEL-N-192-00895-00001 5 5 Air 0.31 0.28 0.52 56
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00895-00002 0.31 0.25 0.46 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00895-00003 0.31 0.25 0.46 56 S
1" Advanced Low-E IG PEL-N-192-00896-00001 5 5 Argon 0.27 0.27 0.52 59 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00896-00002 0.27 0.25 0.46 59 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00896-00003 0.27 0.25 0.46 59 N NC SC S
1" NaturalSun Low-E IG PEL-N-192-00875-00001 5 5 Air 0.31 0.50 0.59 55
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00875-00002 0.31 0.45 0.52 55
with 7/8" Simulated Divided Light grilles PEL-N-192-00875-00003 0.31 0.45 0.52 55
1" NaturalSun Low-E IG PEL-N-192-00876-00001 5 5 Argon 0.28 0.50 0.59 59 N
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00876-00002 0.28 0.45 0.52 59 N
with 7/8" Simulated Divided Light grilles PEL-N-192-00876-00003 0.28 0.45 0.52 59 N
1" SunDefense™ Low-E IG PEL-N-192-00909-00001 5 5 Air 0.30 0.21 0.48 56 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00909-00002 0.30 0.19 0.43 56 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00909-00003 0.30 0.19 0.43 56 NC SC S
1" SunDefense Low-E IG PEL-N-192-00910-00001 5 5 Argon 0.27 0.21 0.48 60 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00910-00002 0.27 0.19 0.43 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00910-00003 0.27 0.19 0.43 60 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-7
350 Series Sliding WindowG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext
.
Mid
.
Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent - 1-1/4" Triple-Pane Insulating Glass N NC SC S CA1-1/4" Advanced Low-E Triple-pane IG PEL-N-192-00929-00001 3 3 3 Air 0.20 0.24 0.41 69 N NC SC S 28 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00929-00002 0.20 0.22 0.37 69 N NC SC S 27 CA
1-1/4" Advanced Low-E Triple-pane IG PEL-N-192-00930-00001 3 3 3 Argon 0.18 0.24 0.41 72 N NC SC S 31 CA with 3/4" or 1" grilles-between-the-glass PEL-N-192-00930-00002 0.18 0.22 0.37 72 N NC SC S 30 CA
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-192-00919-00001 3 3 3 Air 0.25 0.47 0.55 64 N 35 CA with 3/4" or 1" grilles-between-the-glass PEL-N-192-00919-00002 0.25 0.42 0.49 64 N
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-192-00920-00001 3 3 3 Argon 0.22 0.47 0.55 66 N 39 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00920-00002 0.22 0.42 0.49 66 N 36 CA
Vent — with Foam Inserts1-1/4" Advanced Low-E Triple-pane IG PEL-N-192-00887-00001 3 3 3 Air 0.20 0.24 0.41 69 N NC SC S 28 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00887-00002 0.20 0.22 0.37 69 N NC SC S 27 CA
1-1/4" Advanced Low-E Triple-pane IG PEL-N-192-00888-00001 3 3 3 Argon 0.17 0.24 0.41 72 N NC SC S 32 CA with 3/4" or 1" grilles-between-the-glass PEL-N-192-00888-00002 0.17 0.22 0.37 72 N NC SC S 31 CA
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-192-00877-00001 3 3 3 Air 0.24 0.47 0.55 64 N 37 CA with 3/4" or 1" grilles-between-the-glass PEL-N-192-00877-00002 0.24 0.42 0.49 64 N 34 CA
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-192-00878-00001 3 3 3 Argon 0.22 0.47 0.55 67 N 39 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00878-00002 0.22 0.42 0.49 67 N 36 CA
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-8
350 Series Sliding WindowG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 11/16" Dual-Pane Tinted Glass N NC SC S CA11/16" Bronze Advanced Low-E IG PEL-N-192-00939-00001 3 3 Air 0.31 0.28 0.39 56
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00939-00002 0.31 0.25 0.35 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00939-00003 0.31 0.25 0.35 56 S
11/16" Bronze Advanced Low-E IG PEL-N-192-00940-00001 3 3 Argon 0.27 0.28 0.39 59 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00940-00002 0.27 0.25 0.35 59 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00940-00003 0.27 0.25 0.35 59 N NC SC S
11/16" Gray Low-E IG PEL-N-192-00923-00001 3 3 Air 0.32 0.20 0.30 55 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00923-00002 0.32 0.18 0.27 55 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00923-00003 0.32 0.18 0.27 55 S
11/16" Gray Low-E IG PEL-N-192-00924-00001 3 3 Argon 0.28 0.19 0.30 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00924-00002 0.28 0.18 0.27 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00924-00003 0.28 0.18 0.27 59 NC SC S
Tinted Glazing — with Foam Inserts11/16" Bronze Advanced Low-E IG PEL-N-192-00897-00001 3 3 Air 0.31 0.28 0.39 56
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00897-00002 0.31 0.25 0.35 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00897-00003 0.31 0.25 0.35 56 S
11/16" Bronze Advanced Low-E IG PEL-N-192-00898-00001 3 3 Argon 0.27 0.28 0.39 60 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00898-00002 0.27 0.25 0.35 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00898-00003 0.27 0.25 0.35 60 N NC SC S
11/16" Gray Low-E IG PEL-N-192-00881-00001 3 3 Air 0.31 0.20 0.30 55 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00881-00002 0.31 0.18 0.27 55 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00881-00003 0.31 0.18 0.27 55 S
11/16" Gray Low-E IG PEL-N-192-00882-00001 3 3 Argon 0.27 0.19 0.30 59 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00882-00002 0.27 0.18 0.27 59 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00882-00003 0.27 0.18 0.27 59 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-9
350 Series Sliding WindowG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 1" Dual-Pane Tinted 5mm Glass N NC SC S CA1" Bronze Advanced Low-E IG PEL-N-192-00943-00001 5 5 Air 0.31 0.25 0.34 56 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00943-00002 0.31 0.23 0.30 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00943-00003 0.31 0.23 0.30 56 S
1" Bronze Advanced Low-E IG PEL-N-192-00944-00001 5 5 Argon 0.28 0.25 0.34 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00944-00002 0.28 0.22 0.30 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00944-00003 0.28 0.22 0.30 59 NC SC S
1" Gray Low-E IG PEL-N-192-00927-00001 5 5 Air 0.32 0.19 0.29 55 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00927-00002 0.32 0.17 0.26 55 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00927-00003 0.32 0.17 0.26 55 S
1" Gray Low-E IG PEL-N-192-00928-00001 5 5 Argon 0.29 0.19 0.29 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00928-00002 0.29 0.17 0.26 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00928-00003 0.29 0.17 0.26 59 NC SC S
Tinted Glazing — with Foam Inserts1" Bronze Advanced Low-E IG PEL-N-192-00901-00001 5 5 Air 0.31 0.25 0.34 56 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00901-00002 0.31 0.23 0.30 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00901-00003 0.31 0.23 0.30 56 S
1" Bronze Advanced Low-E IG PEL-N-192-00902-00001 5 5 Argon 0.27 0.25 0.34 60 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00902-00002 0.27 0.22 0.30 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00902-00003 0.27 0.22 0.30 60 N NC SC S
1" Gray Low-E IG PEL-N-192-00885-00001 5 5 Air 0.31 0.19 0.29 56 S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00885-00002 0.31 0.17 0.26 56 S
with 7/8" Simulated Divided Light grilles PEL-N-192-00885-00003 0.31 0.17 0.26 56 S
1" Gray Low-E IG PEL-N-192-00886-00001 5 5 Argon 0.28 0.19 0.29 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-192-00886-00002 0.28 0.17 0.26 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-192-00886-00003 0.28 0.17 0.26 59 NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-10
350 Series Sliding Window
Grilles-Between-the-Glass Simulated-Divided-Light Grilles
1"3/4"
1" Contour3/4" Contour1" Contour
1"
3/4" Contour
3/4"
Simulated Divided Light7/8"
7/8"
Prairie Lite Patterns
6-Lite Prairie 9-Lite Prairie
Other Available Patterns
Traditional Top Row
Custom — Equally Divided
For traditional patterns, see size tables.
Grilles
Prairie- Approximately 4" from edge of sash to center of bar.
- Minimum actual glass is 13".
Traditional- Specify number of lites.
- Grille Bars (Grilles) must be equally divided on visible glass.
- Minimum lite size = 6".
Top Row - Top Row dimension must be ≤1/2 actual glass.
Grille Profiles
Grille Patterns
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-11
350 Series Sliding Window
6-0/6-05-0/6-04-0/6-0
6-0/5-05-0/5-04-0/5-03-0/5-0
6-0/4-65-0/4-64-0/4-63-0/4-6
6-0/4-05-0/4-04-0/4-03-0/4-02-6/4-0
6-0/3-65-0/3-64-0/3-63-0/3-62-6/3-62-0/3-6
6-0/3-05-0/3-04-0/3-03-0/3-02-6/3-02-0/3-0
6-0/2-6 5-0/2-6 4-0/2-63-0/2-62-6/2-62-0/2-6
6-0/2-05-0/2-04-0/2-03-0/2-02-6/2-02-0/2-0
6-0/1-65-0/1-64-0/1-63-0/1-62-6/1-62-0/1-6
(1 207)(1 219)
(902)(914)
(749)(762)
(597)(610)
Vent-Fixed Units (XO)
(1 5
11) "
/ 21595'
0"
(1 5
24)
(1 3
59) "
/ 21534'
6"
(1 3
72)
(1 2
07) "
/ 21474'
0"
(1 2
19)
(1 0
54) "
/ 21413'
6"
(1 0
67)
(902
) "/ 21
353' 0
"
(914
)(7
49) "
/ 21292'
6"
(762
)(5
97) "
/ 21232'
0"
(610
)(4
45) "
/ 21171'
6"
(457
)
FrameOpening
(1 8
16) "
/ 21716'
0"
(1 8
29)
(1 816)
"/ 21716' 0"
(1 829)(1 511)
"/ 21595' 0"
(1 524)
"/ 21474' 0"
"/ 21353' 0"
"/ 21292' 6"
"/ 21232' 0"
E
E E
EE
E E
EE
E E
1E
1E
Not to scale.
XO units shown also available as OX
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
Size Tables - Vent-Fixed (XO)
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-12
350 Series Sliding Window
9-0/5-08-0/5-07-0/5-06-0/5-0
9-0/4-68-0/4-67-0/4-66-0/4-6
9-0/4-08-0/4-07-0/4-06-0/4-0
9-0/3-68-0/3-67-0/3-66-0/3-6
9-0/3-08-0/3-07-0/3-06-0/3-0
9-0/2-68-0/2-67-0/2-66-0/2-6
9-0/2-08-0/2-07-0/2-06-0/2-0
9-0/1-68-0/1-67-0/1-66-0/1-6
Vent-Fixed-Vent Units (XOX)
(1 5
11) "
/ 21595'
0"
(1 5
24)
(1 3
59) "
/ 21534'
6"
(1 3
72)
(1 2
07) "
/ 21474'
0"
(1 2
19)
(1 0
54) "
/ 21413'
6"
(1 0
67)
(902
) "/ 21
353' 0
"
(914
)(7
49) "
/ 21292'
6"
(762
)(5
97) "
/ 21232'
0"
(610
)
(2 731)
"/ 211079' 0"
(2 743)(2 426)
"/ 21958' 0"
(2 438)(2 121)
"/ 21837' 0"
(1 829)
(445
) "/ 21
171' 6
"
(457
)
(1 816)
"/ 21716' 0"
(1 829)
FrameOpening
E E E
EEE
E E
EE
E
E
E
E
1E
Not to scale.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
Size Tables - Vent-Fixed-Vent (XOX) Third Vent
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-13
350 Series Sliding Window
9-0/5-08-0/5-07-0/5-06-0/5-0
9-0/4-68-0/4-67-0/4-66-0/4-6
9-0/4-08-0/4-07-0/4-06-0/4-0
9-0/3-68-0/3-67-0/3-66-0/3-6
9-0/3-08-0/3-07-0/3-06-0/3-0
9-0/2-68-0/2-67-0/2-66-0/2-6
9-0/2-08-0/2-07-0/2-06-0/2-0
9-0/1-68-0/1-67-0/1-66-0/1-6
(1 5
11) "
/ 21595'
0"
(1 5
24)
(1 3
59) "
/ 21534'
6"
(1 3
72)
(1 2
07) "
/ 21474'
0"
(1 2
19)
(1 0
54) "
/ 21413'
6"
(1 0
67)
(902
) "/ 21
353' 0
"
(914
)(7
49) "
/ 21292'
6"
(762
)(5
97) "
/ 21232'
0"
(610
)(4
45) "
/ 21171'
6"
(457
)
FrameOpening
Vent-Fixed-Vent Units (XOX)
(2 731)
"/ 211079' 0"
(2 743)(2 426)
"/ 21958' 0"
(2 438)(2 121)
"/ 21837' 0"
(1 829)(1 816)
"/ 21716' 0"
(1 829)
E E
EE
E E
E1E
1E
Not to Scale
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
Size Tables - Vent-Fixed-Vent (XOX) Quarter Vent
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-14
350 Series Sliding Window
FL-H34
FL-H33
FL-H32
FL-24
FL-23
FL-22
FL-34
FL-33
FL-32
FL-D24
FL-D23
FL-D22
26
4"3 /
/" 4
1" 8/
5
"/ 8
3
"/ 8
3
"/ 8
3
"/
78" 8/
5
" 8/5
" 8/5
/ "41/ "41
"/7 8
"/ 83
"1/ 8
"1/ 8
4"3 // "41
4"3 /
"/ 21
"/ 21
5253
5253
3
36"37"
3637
2H3
252527
Call SizeMasonry
BuckFrame
Tip to Tip
4
49 49 505038 383737
32 26
"25 25
"26
"
D27473
74"73"
E
EE
Not to scale.
Size Tables - 5/8" Integral Flange Vent-Fixed (XO)
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-15
350 Series Sliding Window
FL-D34
FL-D33
FL-D32
FL-34
FL-33
FL-32
FL-D24
FL-D23
FL-D22
/" 4
1" 8/
5
"/ 8
3
"/ 8
3
"/ 8
3
"/
78" 8/
5
" 8/5
" 8/5
Call SizeMasonry
BuckFrame
Tip to Tip
4
49 49 505038 383737
32 26
"25 25
"26
"
"/ 83
"1/ 8
"8/5
D3107105105 "/ 83
106
4"3 /
/ "41
"/7 8
"/ 83
"1/ 8
"1/ 8
5253
5253
3 D27473
74"73"
E
E
FL-D34
FL-D33
FL-D32
FL-34
FL-33
FL-32
FL-D24
FL-D23
FL-D22
"/ 83
"1/ 8
"8/5
D3107105105 "/ 83
106
4"3 /
/ "41
"/7 8
"/ 83
"1/ 8
"1/ 8
5253
5253
3 D27473
74"73"
/" 4
1" 8/
5
"/ 8
3
"/ 8
3
"/ 8
3
"/
78" 8/
5
" 8/5
" 8/5
Call SizeMasonry
BuckFrame
Tip to Tip
4
49 49 505038 383737
32 26
"25 25
"26
"
1E
1E
Not to scale.
Size Tables - 5/8" Integral Flange Third Vent and Quarter Vent (XOX)
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-16
350 Series Sliding Window
Minimum Maximum
XO
or
OX
Un
its
21-1/2"W x 11-1/2"H(546 x 292)
76"W x 72"H(1 828 x 18 288)
XO
X u
nit
s
47-1/2"W x 11-1/2"H(1 207 x 292)
114"W x 72"H(2 896 x 18 288)
(1) Calculated based on standard hardware.
To convert areas to square meters (m2), multiply square feet by 0.0929
Key:
AGW = Actual Glass Width AGH = Actual Glass Height FW = Frame Width FH = Frame Height VGW = Visible Glass Width VGH = Visible Glass Height
Miscellaneous Formulas
Equal Vent (XO and OX)
Quarter Vent (XOX)
Third vent (XOX)
Actual Glass
AGW = (FW - 4.876 ) ÷ 2 AGW = (FW - 10.25 ) ÷ 4 AGW = (FW - 7.563 ) ÷ 3
AGH = FH - 5.312
Visible Glass
VGW = AGW - 1.112
VGH = AGH - 1.112
Clear Opening 1
COW = (FW - 9.874) ÷ 2 COW = (FW - 9.638) ÷ 4 COW = (FW - 15.375) ÷ 3
COH = FH - 4.063
General Notes:
XO/OX Units:Rough Opening = Frame Dimension + 1/2"
Maximum Frame Height ≤ Frame Width x 1.75
Bronze glass is limited to 22 Ft 2 (glass size).
If glass width / height ratio is > 5:1, then unit must be tempered.
XOX Units:Rough Opening = Frame Dimension + 1/2"
Sash split options are 1/4 width and 1/3 width of frame
1/4 Vent XOX Units: Max frame height ≤ frame width X 0.875
1/3 Vent XOX Units: Max frame height ≤ frame width X 1.167)
Bronze glass is limited to 22 Ft 2 (glass size).
If glass width / height ratio is > 5:1, then unit must be tempered.
Special Sizes and Dimensions
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-17
350 Series Sliding Window
1-WIDE OX, XO UNITS — EQUAL SASH
Unit
Eg
ress Frame Clear Opening Visible
Glass Ft 2
Standard Glass Thickness (mm) Standard
Performance Class & Grade 1Width
(Inches)Height (Inches)
Width (Inches)
Height (Inches)
Ft 2 Annealed Tempered
2-0/1-6 23-1/2 17-1/2 6-13/16 13-7/16 0.6 1.3 2.5 3 LC402-0/2-0 23-1/2 23-1/2 6-13/16 19-7/16 0.9 1.9 2.5 3 LC402-0/2-6 23-1/2 29-1/2 6-13/16 25-7/16 1.2 2.6 2.5 3 LC402-0/3-0 23-1/2 35-1/2 6-13/16 31-7/16 1.4 3.3 2.5 3 LC402-0/3-6 23-1/2 41-1/2 6-13/16 37-7/16 1.7 4.0 2.5 3 LC402-6/1-6 29-1/2 17-1/2 9-13/16 13-7/16 0.9 1.7 2.5 3 LC402-6/2-0 29-1/2 23-1/2 9-13/16 19-7/16 1.3 2.7 2.5 3 LC402-6/2-6 29-1/2 29-1/2 9-13/16 25-7/16 1.7 3.6 2.5 3 LC402-6/3-0 29-1/2 35-1/2 9-13/16 31-7/16 2.1 4.5 2.5 3 LC402-6/3-6 29-1/2 41-1/2 9-13/16 37-7/16 2.5 5.4 2.5 3 LC402-6/4-0 29-1/2 47-1/2 9-13/16 43-7/16 2.9 6.4 2.5 3 LC403-0/1-6 35-1/2 17-1/2 12-13/16 13-7/16 1.1 2.2 2.5 3 LC403-0/2-0 35-1/2 23-1/2 12-13/16 19-7/16 1.7 3.4 2.5 3 LC403-0/2-6 35-1/2 29-1/2 12-13/16 25-7/16 2.2 4.5 2.5 3 LC403-0/3-0 35-1/2 35-1/2 12-13/16 31-7/16 2.7 5.7 2.5 3 LC403-0/3-6 35-1/2 41-1/2 12-13/16 37-7/16 3.3 6.9 2.5 3 LC403-0/4-0 35-1/2 47-1/2 12-13/16 43-7/16 3.8 8.1 2.5 3 LC403-0/4-6 35-1/2 53-1/2 12-13/16 49-7/16 4.3 9.3 2.5 3 LC403-0/5-0 35-1/2 59-1/2 12-13/16 55-7/16 4.9 10.5 2.5 3 LC404-0/1-6 47-1/2 17-1/2 18-13/16 13-7/16 1.7 3.1 2.5 3 LC404-0/2-0 47-1/2 23-1/2 18-13/16 19-7/16 2.5 4.8 2.5 3 LC404-0/2-6 47-1/2 29-1/2 18-13/16 25-7/16 3.3 6.5 2.5 3 LC404-0/3-0 47-1/2 35-1/2 18-13/16 31-7/16 4.1 8.1 2.5 3 LC404-0/3-6 47-1/2 41-1/2 18-13/16 37-7/16 4.8 9.8 2.5 3 LC404-0/4-0 47-1/2 47-1/2 18-13/16 43-7/16 5.6 11.5 2.5 3 LC404-0/4-6 47-1/2 53-1/2 18-13/16 49-7/16 6.4 13.2 2.5 3 LC404-0/5-0 47-1/2 59-1/2 18-13/16 55-7/16 7.2 14.9 3 3 LC404-0/6-0 47-1/2 71-1/2 18-13/16 67-7/16 8.8 18.2 2.5 3 LC405-0/1-6 59-1/2 17-1/2 24-13/16 13-7/16 2.3 4.0 2.5 3 LC405-0/2-0 59-1/2 23-1/2 24-13/16 19-7/16 3.3 6.2 2.5 3 LC405-0/2-6 59-1/2 29-1/2 24-13/16 25-7/16 4.3 8.4 2.5 3 LC405-0/3-0 E1 59-1/2 35-1/2 24-13/16 31-7/16 5.4 10.6 2.5 3 LC405-0/3-6 E 59-1/2 41-1/2 24-13/16 37-7/16 6.4 12.8 2.5 3 LC405-0/4-0 E 59-1/2 47-1/2 24-13/16 43-7/16 7.4 14.9 2.5 3 LC405-0/4-6 E 59-1/2 53-1/2 24-13/16 49-7/16 8.5 17.1 2.5 3 LC405-0/5-0 E 59-1/2 59-1/2 24-13/16 55-7/16 9.5 19.3 3 3 LC405-0/6-0 E 59-1/2 71-1/2 24-13/16 67-7/16 11.6 23.7 3 3 LC406-0/1-6 71-1/2 17-1/2 30-13/16 13-7/16 2.8 4.9 2.5 3 LC406-0/2-0 71-1/2 23-1/2 30-13/16 19-7/16 4.1 7.6 2.5 3 LC406-0/2-6 E1 71-1/2 29-1/2 30-13/16 25-7/16 5.4 10.3 2.5 3 LC406-0/3-0 E 71-1/2 35-1/2 30-13/16 31-7/16 6.7 13.0 2.5 3 LC406-0/3-6 E 71-1/2 41-1/2 30-13/16 37-7/16 8.0 15.7 2.5 3 LC406-0/4-0 E 71-1/2 47-1/2 30-13/16 43-7/16 9.2 18.4 2.5 3 LC406-0/4-6 E 71-1/2 53-1/2 30-13/16 49-7/16 10.5 21.0 3 3 LC406-0/5-0 E 71-1/2 59-1/2 30-13/16 55-7/16 11.8 23.7 3 3 LC406-0/6-0 E 71-1/2 71-1/2 30-13/16 67-7/16 14.4 29.1 3 3 LC40
(1) Maximum performance when glazed with the appropriate glass thickness.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2. To convert areas to square meters (m²), multiply square feet by 0.0929.
Design Data - Equal Sash (OX, XO)
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-18
350 Series Sliding Window
XOX SLIDING WINDOW — THIRD VENT
Unit
Eg
ress Frame Clear Opening Visible
Glass Ft 2
Standard Glass Thickness (mm) Standard
Performance Class & Grade 1Width
(Inches)Height (Inches)
Width (Inches)
Height (Inches)
Ft 2 Annealed Tempered
6-0/1-6 71-1/2 17-1/2 18-11/16 13-7/16 1.7 4.7 2.5 3 LC306-0/2-0 71-1/2 23-1/2 18-11/16 19-7/16 2.5 7.2 2.5 3 LC306-0/2-6 71-1/2 29-1/2 18-11/16 25-7/16 3.3 9.8 2.5 3 LC306-0/3-0 71-1/2 35-1/2 18-11/16 31-7/16 4.0 12.3 2.5 3 LC306-0/3-6 71-1/2 41-1/2 18-11/16 37-7/16 4.8 14.9 2.5 3 LC306-0/4-0 71-1/2 47-1/2 18-11/16 43-7/16 5.6 17.4 2.5 3 LC306-0/4-6 71-1/2 53-1/2 18-11/16 49-7/16 6.4 20.0 2.5 3 LC256-0/5-0 71-1/2 59-1/2 18-11/16 55-7/16 7.1 22.5 2.5 3 LC257-0/1-6 83-1/2 17-1/2 22-11/16 13-7/16 2.1 5.6 2.5 3 LC307-0/2-0 83-1/2 23-1/2 22-11/16 19-7/16 3.0 8.7 2.5 3 LC307-0/2-6 83-1/2 29-1/2 22-11/16 25-7/16 4.0 11.7 2.5 3 LC307-0/3-0 83-1/2 35-1/2 22-11/16 31-7/16 4.9 14.8 2.5 3 LC307-0/3-6 E 83-1/2 41-1/2 22-11/16 37-7/16 5.9 17.8 2.5 3 LC307-0/4-0 E 83-1/2 47-1/2 22-11/16 43-7/16 6.8 20.9 2.5 3 LC307-0/4-6 E 83-1/2 53-1/2 22-11/16 49-7/16 7.7 23.9 2.5 3 LC257-0/5-0 E 83-1/2 59-1/2 22-11/16 55-7/16 8.7 27.0 3 3 LC258-0/1-6 95-1/2 17-1/2 26-11/16 13-7/16 2.4 6.5 2.5 3 LC308-0/2-0 95-1/2 23-1/2 26-11/16 19-7/16 3.6 10.1 2.5 3 LC308-0/2-6 95-1/2 29-1/2 26-11/16 25-7/16 4.7 13.6 2.5 3 LC308-0/3-0 E 95-1/2 35-1/2 26-11/16 31-7/16 5.8 17.2 2.5 3 LC308-0/3-6 E 95-1/2 41-1/2 26-11/16 37-7/16 6.9 20.7 2.5 3 LC308-0/4-0 E 95-1/2 47-1/2 26-11/16 43-7/16 8.0 24.3 2.5 3 LC308-0/4-6 E 95-1/2 53-1/2 26-11/16 49-7/16 9.1 27.8 2.5 3 LC258-0/5-0 E 95-1/2 59-1/2 26-11/16 55-7/16 10.2 31.4 3 3 LC259-0/1-6 107-1/2 17-1/2 30-11/16 13-7/16 2.8 7.5 2.5 3 LC309-0/2-0 107-1/2 23-1/2 30-11/16 19-7/16 4.1 11.5 2.5 3 LC309-0/2-6 E1 107-1/2 29-1/2 30-11/16 25-7/16 5.4 15.6 2.5 3 LC309-0/3-0 E 107-1/2 35-1/2 30-11/16 31-7/16 6.7 19.6 2.5 3 LC309-0/3-6 E 107-1/2 41-1/2 30-11/16 37-7/16 7.9 23.7 2.5 3 LC309-0/4-0 E 107-1/2 47-1/2 30-11/16 43-7/16 9.2 27.7 2.5 3 LC309-0/4-6 E 107-1/2 53-1/2 30-11/16 49-7/16 10.5 31.8 3 3 LC259-0/5-0 E 107-1/2 59-1/2 30-11/16 55-7/16 11.8 35.8 3 3 LC25
(1) Maximum performance when glazed with the appropriate glass thickness.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2. To convert areas to square meters (m²), multiply square feet by 0.0929.
Design Data - Vent-Fixed-Vent (XOX) Third Vent
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-19
350 Series Sliding Window
XOX SLIDING WINDOW — QUARTER VENT
Unit
Eg
ress Frame Clear Opening Visible
Glass Ft 2
Standard Glass Thickness (mm) Standard
Performance Class & Grade 1Width
(Inches)Height (Inches)
Width (Inches)
Height (Inches)
Ft 2 Annealed Tempered
6-0/1-6 71-1/2 17-1/2 15-7/16 13-7/16 1.4 4.7 2.5 3 LC306-0/2-0 71-1/2 23-1/2 15-7/16 19-7/16 2.0 7.2 2.5 3 LC306-0/2-6 71-1/2 29-1/2 15-7/16 25-7/16 2.7 9.8 2.5 3 LC306-0/3-0 71-1/2 35-1/2 15-7/16 31-7/16 3.3 12.3 2.5 3 LC306-0/3-6 71-1/2 41-1/2 15-7/16 37-7/16 4.0 14.9 2.5 3 LC306-0/4-0 71-1/2 47-1/2 15-7/16 43-7/16 4.6 17.4 2.5 3 LC306-0/4-6 71-1/2 53-1/2 15-7/16 49-7/16 5.3 20.0 3 3 LC256-0/5-0 71-1/2 59-1/2 15-7/16 55-7/16 5.9 22.5 3 3 LC257-0/1-6 83-1/2 17-1/2 18-7/16 13-7/16 1.7 5.6 2.5 3 LC307-0/2-0 83-1/2 23-1/2 18-7/16 19-7/16 2.4 8.7 2.5 3 LC307-0/2-6 83-1/2 29-1/2 18-7/16 25-7/16 3.2 11.7 2.5 3 LC307-0/3-0 83-1/2 35-1/2 18-7/16 31-7/16 4.0 14.8 2.5 3 LC307-0/3-6 83-1/2 41-1/2 18-7/16 37-7/16 4.7 17.8 2.5 3 LC307-0/4-0 83-1/2 47-1/2 18-7/16 43-7/16 5.5 20.9 3 3 LC307-0/4-6 83-1/2 53-1/2 18-7/16 49-7/16 6.3 23.9 3 3 LC257-0/5-0 83-1/2 59-1/2 18-7/16 55-7/16 7.1 27.0 3 3 LC258-0/1-6 95-1/2 17-1/2 21-7/16 13-7/16 2.0 6.5 2.5 3 LC308-0/2-0 95-1/2 23-1/2 21-7/16 19-7/16 2.8 10.1 2.5 3 LC308-0/2-6 95-1/2 29-1/2 21-7/16 25-7/16 3.7 13.6 2.5 3 LC308-0/3-0 95-1/2 35-1/2 21-7/16 31-7/16 4.6 17.2 2.5 3 LC308-0/3-6 E1 95-1/2 41-1/2 21-7/16 37-7/16 5.5 20.7 3 3 LC308-0/4-0 E 95-1/2 47-1/2 21-7/16 43-7/16 6.4 24.3 3 3 LC308-0/4-6 E 95-1/2 53-1/2 21-7/16 49-7/16 7.3 27.8 3 3 LC258-0/5-0 E 95-1/2 59-1/2 21-7/16 55-7/16 8.2 31.4 3 3 LC259-0/1-6 107-1/2 17-1/2 24-7/16 13-7/16 2.2 7.5 2.5 3 LC259-0/2-0 107-1/2 23-1/2 24-7/16 19-7/16 3.3 11.5 2.5 3 LC259-0/2-6 107-1/2 29-1/2 24-7/16 25-7/16 4.3 15.6 3 3 LC259-0/3-0 E1 107-1/2 35-1/2 24-7/16 31-7/16 5.3 19.6 3 3 LC259-0/3-6 E 107-1/2 41-1/2 24-7/16 37-7/16 6.3 23.7 3 3 LC259-0/4-0 E 107-1/2 47-1/2 24-7/16 43-7/16 7.3 27.7 3 3 LC259-0/4-6 E 107-1/2 53-1/2 24-7/16 49-7/16 8.3 31.8 3 5 LC259-0/5-0 E 107-1/2 59-1/2 24-7/16 55-7/16 9.4 35.8 3 5 LC25
(1) Maximum performance when glazed with the appropriate glass thickness.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2. To convert areas to square meters (m²), multiply square feet by 0.0929.
Design Data - Vent-Fixed-Vent (XOX) Quarter Vent
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-20
350 Series Sliding Window
XO/OX Vent Units
Unit
Eg
ress Frame Clear Opening Visible
Glass Ft 2
Frame Area Ft 2
Standard Performance
Class & Grade 1Width (Inches)
Height (Inches)
Width (Inches)
Height (Inches)
Ft 2
FL-H32 25-1/2 25 7-13/16 21 1.1 3.2 4.4 LC40FL-H33 25-1/2 37-3/8 7-13/16 33-5/16 1.8 5.0 6.6 LC40FL-H34 25-1/2 49-5/8 7-13/16 45-1/2 2.4 6.8 8.8 LC40FL-22 36 25 13-1/16 21 1.8 4.7 6.3 LC40FL-23 36 37-3/8 13-1/16 33-5/16 3.0 7.4 9.3 LC40FL-24 36 49-5/8 13-1/16 45-1/2 4.1 10.2 12.4 LC40FL-32 52-1/8 25 21-1/16 21 3.0 7.0 9.0 LC40FL-33 52-1/8 37-3/8 21-1/16 33-5/16 4.8 11.2 13.5 LC40FL-34 E 52-1/8 49-5/8 21-1/16 45-1/2 6.6 15.3 18.0 LC40
FL-D22 73 25 31-1/2 21 4.5 10.1 12.7 LC40FL-D23 E 73 37-3/8 31-1/2 33-5/16 7.2 16.0 18.9 LC40FL-D24 E 73 49-5/8 31-1/2 45-1/2 9.9 21.9 25.2 LC40
(1) Maximum performance when glazed with the appropriate glass thickness.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2. E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2. To convert areas to square meters (m²), multiply square feet by 0.0929.
Design Data - 5/8" Integral Flange
XOX 1/4 Vent Units
Unit
Eg
ress Frame Clear Opening Visible
Glass Ft 2
Frame Area Ft 2
Standard Performance
Class & Grade 1Width (Inches)
Height (Inches)
Width (Inches)
Height (Inches)
Ft 2
FL-32 52-1/8 25 10-9/16 21 1.5 7.0 9.0 LC30FL-33 52-1/8 37-3/8 10-9/16 33-5/16 2.4 11.2 13.5 LC30FL-34 52-1/8 49-5/8 10-9/16 45-1/2 3.3 15.3 18.0 LC30
FL-D22 73 25 15-13/16 21 2.3 10.1 12.7 LC25FL-D23 73 37-3/8 15-13/16 33-5/16 3.6 16.0 18.9 LC25FL-D24 73 49-5/8 15-13/16 45-1/2 5.0 21.9 25.2 LC25FL-D32 105-3/8 25 23-7/8 21 3.4 14.8 18.3 LC25FL-D33 E1 105-3/8 37-3/8 23-7/8 33-5/16 5.5 23.6 27.3 LC25FL-D34 E1 105-3/8 49-5/8 23-7/8 45-1/2 7.5 32.2 36.3 LC25
XOX 1/3 Vent Units
Unit
Eg
ress Frame Clear Opening Visible
Glass Ft 2
Frame Area Ft 2
Standard Performance
Class & Grade 1Width (Inches)
Height (Inches)
Width (Inches)
Height (Inches)
Ft 2
FL-32 52-1/8 25 12-1/4 21 1.7 7.0 9.0 LC30FL-33 52-1/8 37-3/8 12-1/4 33-5/16 2.8 11.2 13.5 LC30FL-34 52-1/8 49-5/8 12-1/4 45-1/2 3.8 15.3 18.0 LC30
FL-D22 73 25 19-3/16 21 2.7 10.1 12.7 LC25FL-D23 73 37-3/8 19-3/16 33-5/16 4.4 16.0 18.9 LC25FL-D24 73 49-5/8 19-3/16 45-1/2 6.0 21.9 25.2 LC25FL-D32 105-3/8 25 30 21 4.3 14.8 18.3 LC25FL-D33 E 105-3/8 37-3/8 30 33-5/16 6.9 23.6 27.3 LC25FL-D34 E 105-3/8 49-5/8 30 45-1/2 9.4 32.2 36.3 LC25
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-21
350 Series Sliding Window
(1) Dual-Pane IG High Altitude glazings are available with or without Argon. Triple-Pane IG High Altitude glazings are only available without Argon.
(2) Obscure glass not available with Bronze Advanced Low-E IG.
(3) Almond grilles only available on almond units. Almond units with grilles will have an almond grille color.
Frame • Overall frame depth: 4-1/2" on all frame types except the 3-1/4" Block
Pocket Replacement frame. The 3-1/4" Block Pocket Replacement frame has an overall frame depth of 4-7/8".
• Frame members are mitered and heat fused to provide a fully welded corner assembly with SmoothSeam™ virtually invisible interior corner welds. Sill is fitted with weeps.
• Frame: [1-7/16" setback nail fin for 3-1/16" wall depth] [Block frame for 4-1/2" wall depth] [Block frame for 3-1/4" Block Pocket Replacement install] [Flush flange for 4-1/16" wall depth] [Integral flange for 3-7/8" wall depth].
• Interior and exterior frame surfaces are extruded rigid uPVC.
Sash• Sash members are extruded, rigid uPVC [with optional foam insulation].• Sash members are mitered and heat-fused to provide a fully welded corner
assembly with SmoothSeam™ virtually invisible interior corner welds.• Includes an integral extruded sash slide.• Contains sealed insulating glass.
Weatherstripping• Sash is weatherstripped around the sash perimeter with a fin-type, pile
weatherstripping.
Glazing System• Quality float glass complying with ASTM C 1036.• Exterior face-glazed sealed insulating glass. • Dual-Pane insulating glass [[annealed] [tempered]] [Advanced
Low-E coated [with Argon]] [NaturalSun Low-E coated [with Argon]] [SunDefense™ Low-E coated [with Argon]] [Bronze, Advanced Low-E coated [with Argon]] [Gray Low-E coated [with Argon]] [Obscure 2] [High Altitude 1].
- or -• Triple-Pane insulating glass [[annealed] [tempered]] [Advanced Low-E
coated with Argon] [NaturalSun Low-E coated with Argon] [Obscure 2] [High Altitude 1].
Interior / Exterior• Window frame and sash members are [[White] [Almond] with integral color
extruded throughout the profiles] [[Brown] [Black] [Brick Red] [Hartford Green] [Morning Sky Gray] [Poplar White] [Portobello] [Tan] [Fossil] exterior, consisting of a solar reflective coating exceeding AAMA 613 test requirements, with White integral color extruded throughout the profiles on the interior].
• All exposed PVC surfaces are smooth, glossy and uniform in appearance.
Hardware • Locks are factory-installed, zinc die cast, self-aligning, [cam action lock]
[autolock] located on the checkrail.• Two sash locks are installed on units with 29-1/2" or greater frame height.• Vents are equipped with two nylon roller housings containing two nylon
rollers each.• Hardware finish is [White] [Almond] [Bright Brass] [Satin Nickel]
[Oil-Rubbed Bronze].
Screens• Set in aluminum frame and fitted to exterior of window.• Screen frame finish is baked enamel, color to match exterior• Screens for window with frame height ≤ 51-1/2" have one plunger per
side, screens for windows with frame height > 51-1/2" have two plungers per side. Screens for windows with frame width > 39" or frame height > 53-1/2" have a screen spreader bar. Supplied complete with all necessary hardware.
• Conventional Black Fiberglass � Black vinyl coated 18/16 mesh fiberglass screen cloth complying with
ASTM D 3656 and SMA 1201.- or -
• InView™ Screens � Black vinyl coated 18/18 mesh fiberglass screen cloth complying with
SMA 1201.
Optional ProductsGrilles • Grilles-Between-the-Glass
� Insulating glass contains [3/4"] [1"] contoured profile aluminum grilles permanently installed between two panes of glass.
� Patterns are [Traditional] [9-Lite Prairie] [Top Row] [Custom–Equally Divided].
� Interior grille color matches interior frame. � Exterior grille color [3/4" Grille is [White] [Almond 3] [Brown] [Black]
[Brick Red] [Hartford Green] [Morning Sky Gray] [Poplar White] [Portobello] [Tan] [Fossil]] [1" Grille is [White] [Almond 3] [Brown]].
� Available on units glazed with dual-pane and triple-pane insulated glass.
• Simulated-Divided-Light grilles without spacer � 7/8" Grilles permanently bonded to the interior and exterior of glass. � Patterns are [Traditional] [6-Lite Prairie] [9-Lite Prairie] [Top Row]
[Custom–Equally Divided]. � Grilles match color of interior and exterior frame. � Available only on units glazed with dual-pane insulated glass.
Hardware • Optional limited opening hardware available for vent units in [White]
[Almond] extruded vinyl to match the unit; nominal 3-3/4" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
Detailed Product Description
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-22
350 Series Sliding Window
XS
OH
OS
I
XH
VJFJ
VENT JAMBVJFJ FIXED JAMB INTERLOCKERI
VENT SILLXS
VENT HEADXH
FIXED SILLOS
FIXED HEADOH
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - Optional Foam Insulation
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-23
350 Series Sliding Window
GLAZING OPTIONS
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[47]
1 7/
8"[3
5]1
3/8"
[16]5/8"
[98]3 7/8"
[11]7/16"
[103]4 1/16"
[49]
1 15
/16"
[114]4 1/2"
[49]
1 15
/16"
[114]4 1/2"
PANE IG1 1/4" TRIPLE
1" IG
[49]
1 15
/16"
[16]
5/8"
5/8" INTEGRAL FLANGEBLOCK FRAME with
REPLACEMENTPOCKET
[83]3 1/4"
[49]
1 15
/16"
FLUSH FLANGEDOUBLE WALL
[49]
1 15
/16"
[57]
2 1/
4"
with J-CHANNELNAIL FIN
[19]
3/4"
[49]
1 15
/16"
[44]
1 3/
4"
[37]1 7/16"
[78]3 1/16"
NAIL FINSTANDARD
[44]
1 3/
4"
[49]
1 15
/16"
[37]1 7/16"
[78]3 1/16"
[49]
1 15
/16"
[114]4 1/2"
BLOCK FRAMESTANDARD
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - Frame Types
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-24
350 Series Sliding Window
[82]
3 1/
4"[8
2]3
3/16
"
[114
]4
1/2"
[44]1 3/4"
[37]
1 7/
16"
[47]1 7/8"
[32]1 1/4"
[48]1 7/8"
[47]
1 13
/16"
[62]
2 7/
16"
[59]
2 5/
16"
[46]1 13/16"
[34]1 3/8"
[49]1 15/16"
[52]2"
FRAME WIDTH
[44]1 3/4"
[78]
3 1/
16"
[44]
1 3/
4"
[37]1 7/16"
[51]2"
[44]
1 3/
4"
[44]
1 3/
4"
[44]
1 3/
4"
[82]
3 3/
16"
[47]1 13/16"
6 9/16"4 9/16"
[38]1 1/2"
Optional Factory Applied Wood Jamb Extensions
[89]3 1/2"
[16]
5/8"
[49]
1 15
/16"
[37]1 7/16"
[78]3 1/16"
FRAM
E H
EIG
HT
[49]
1 15
/16"
[114]4 1/2"
[167]6 9/16"
[116]4 9/16"
[78]3 1/16"
FRAM
E H
EIG
HT
[82]
3 1/
4" [49]
1 15
/16"
[114]4 1/2" OAW
XS
OH
OS
I
XH
VJFJ
VENT JAMBVJFJ FIXED JAMB INTERLOCKERI
VENT SILLXSFIXED SILLOS
FIXED HEADOH VENT HEADXH
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - OX / XO
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-25
350 Series Sliding Window
[32]
1 1/
4"[4
8]1
7/8"
[32]
1 1/
4"[4
8]1
7/8"
[48]
1 7/
8"
[114
]4
1/2"
[44]1 3/4"
[44]1 3/4"
[37]
1 7/
16"
[84]3 5/16"
[47]1 7/8"
[32]1 1/4"
[48]1 7/8"
[47]
1 13
/16"
[62]
2 7/
16"
FRAME WIDTH
[78]
3 1/
16"
[47]
1 13
/16"
[34]1 3/8"
[49]1 15/16"
[46]1 13/16"
[46]1 13/16"
[49]1 15/16"
[34]1 3/8"
[44]
1 3/
4"
[37]1 7/16"
[51]2"
[44]
1 3/
4"
[44]
1 3/
4"
[44]
1 3/
4"
[82]
3 3/
16"
[47]1 13/16"
6 9/16"4 9/16"
[38]1 1/2"
Optional Factory Applied Wood Jamb Extensions
[89]3 1/2"
[16]
5/8"
[49]
1 15
/16"
[33]
1 5/
16"
[37]1 7/16"
[78]3 1/16"
FRAM
E H
EIG
HT
[49]
1 15
/16"
[114]4 1/2"
[167]6 9/16"
[116]4 9/16"
[78]3 1/16"
FRAM
E H
EIG
HT
[82]
3 1/
4" [49]
1 15
/16"
[114]4 1/2" OAW
OS
VJI
XHOH
VJ
XS
VENT JAMBVJVENT JAMBVJ INTERLOCKERIINTERLOCKERI
VENT SILLXSFIXED SILLOS
FIXED HEADOH VENT HEADXH
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - OXO
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-SW-26
350 Series Sliding Window
[123
]4
13/1
6"
[40]
1 9/
16"
[14]9/16"
[37]1 7/16"
[47]1 7/8"
[32]1 1/4"
[48]1 7/8"
[47]
1 13
/16"
[62]
2 7/
16"
[59]
2 5/
16"
FRAME WIDTH
[34]1 3/8"
[49]1 15/16"
[46]1 13/16"[52]
2"
[83]
3 1/
4"
[82]
3 1/
4"[8
2]3
3/16
"
FRAM
E H
EIG
HT
[43]
1 11
/16"
[82]
3 3/
16"
[47]1 13/16"
[49]
1 15
/16"
[49]
1 15
/16"
FRAM
E H
EIG
HT
[82]
3 3/
16" [4
9]1
15/1
6"
[83]3 1/4"
[40]1 9/16"
[43]
1 11
/16"
[83]3 1/4"
[40]1 9/16"
[123]4 13/16"
[83]3 1/4"
[49]
1 15
/16"
[123]4 13/16"
[83]3 1/4"
XS
OH
OS
I
XH
VJFJ
VENT HEADXH
VENT JAMBVJFJ FIXED JAMB INTERLOCKERI
VENT SILLXSFIXED SILLOS
FIXED HEADOH
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - Block Pocket Replacement Frame, OX / XO