sjtu1 chapter 10 sinusoidal steady-state analysis
TRANSCRIPT
SJTU 1
Chapter 10
Sinusoidal steady-state analysis
SJTU 2
Steps to analyze ac circuit
1. Transform the circuit to the phasor or frequency domain
2. Solve the problem using circuit techniques(nodal analysis, mesh analysis, superposition,etc)
3. Transform the resulting phasor to the time domain
SJTU 3
Nodal analysis
Fig. 8-28: An example node
SJTU 4
Mesh analysis
planar circuits: Circuits that can be drawn on a flat surface with no crossovers
Fig. 8-29: An example mesh
the sum of voltages around mesh A is
SJTU 5
EXAMPLE 8-21Use node analysis to find the current IX in Fig. 8-31.
Fig. 8-31
SOLUTION:
075VC :C Node
or
SJTU 6
SJTU 7
EXAMPLE 8-24 The circuit in Fig. 8-32 is an equivalent circuit of an ac induction motor. The current IS is called the stator current, IR the rotor current, and IM the magnetizing current. Use the mesh-current method to solve for the branch currents IS, IR and IM.
SJTU 8
SJTU 9
EXAMPLE 8-25
Use the mesh-current method to solve for output voltage V2 and input impedance ZIN of the circuit below.
SOLUTION:
SJTU 10
SJTU 11
Example
Frequency domain equivalent of the circuit
SJTU 12
Example
SJTU 13
Find Vo/Vi, Zi
See F page417
SJTU 14
Circuit Theorems with Phasors
PROPORTIONALITY
The proportionality property states that phasor output responses are proportional to the input phasor
where X is the input phasor, Y is the output phasor, and K is the proportionality constant.
SJTU 15
EXAMPLE 8-13
Use the unit output method to find the input impedance, current I1, output voltage VC, and current I3 of the circuit in Fig. 8-20 for Vs= 10 0°∠
SOLUTION:
1.Assume a unit output voltage . 2.By Ohm's law, . 3.By KVL, 4.By Ohm's law, 5.By KCL, 6.By KCL,
SJTU 16
Given K and ZIN, we can now calculate the required responses for an input
SJTU 17
Two cases:
1. With same frequency sources.
2. With different frequency sources
EXAMPLE 8-14
Use superposition to find the steady - state voltage vR (t) in Fig. 8 - 21 for R=20 , L1 = 2mH, L2 = 6mH, C = 20 F, V s1= 100cos 5000t V , and Vs2=120cos (5000t +30 )V.
SUPERPOSITION
SJTU 18
SOLUTION:
Fig. 8-22
SJTU 19
SJTU 20
EXAMPLE 8-15
Fig. 8-23
Use superposition to find the steady-state current i(t) in Fig. 8-23 for R=10k , L=200mH, vS1=24cos20000t V, and vS2=8cos(60000t+30 ° ).
SOLUTION: With source no. 2 off and no.1 on
SJTU 21
With source no.1 off and no.2 on
The two input sources operate at different frequencies, so that phasors responses I1 and I2 cannot be added to obtain the overall response. In this case the overall response is obtained by adding the corresponding time-domain functions.
SJTU 22
More examples
See F page403
SJTU 23
The thevenin and Norton circuits are equivalent to each other, so their circuit parameters are related as follows:
THEVENIN AND NORTON EQUIVALENT CIRCUITS
SJTU 24
Source transformation
SJTU 25
EXAMPLE 8-17
Both sources in Fig. 8-25(a) operate at a frequency of =5000 rad/s. Find the steady-state voltage vR(t) using source transformations.
SOLUTION:
+
SJTU 26
EXAMPLE 8-18 Use Thevenin's theorem to find the current Ix in the bridge circuit shown in Fig. 8-26.
Fig. 8-26
SJTU 27
SOLUTION:
SJTU 28
SJTU 29