sony mhs-pm1 service manual ver 1.1 2009.06 rev-1 (9-852-668-12)
TRANSCRIPT
Revision HistoryRevision History
Sony EMCS Co.MHS-PM1
SERVICE MANUAL
LinkLink
Internal memoryON BOARD
Internal memoryON BOARD
SPECIFICATIONS DISASSEMBLY
SERVICE NOTE
REPAIR PARTS LIST
BLOCK DIAGRAM
Ver. 1.1 2009.06
2009F0500-1 © 2009.6
Published by Kohda TEC9-852-668-12
US ModelCanadian Model
AEP ModelUK Model
North European ModelE Model
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
MOBILE HD SNAP CAMERA
MHS-PM1
In case of the main board or main frame assy failure, contactyour local Sony Service Headquarter for the measures.
Photo: Silver
Revised-1Replacement of the previously issuedSERVICE MANUAL 9-852-668-11with this manual.
— 2 —MHS-PM1
SPECIFICATIONS
Camera
[System]Image device: 7.13 mm (1/2.5 type) CMOS
sensorTotal pixel number of camera:
Approx. 5 040 000 (2 592 × 1 944) pixelsEffective pixel number of camera:
Approx. 5 040 000 (2 592 × 1 944) pixels (still images), Approx. 2 074 000 pixels([1080 30P] movie)
Lens: F3.6f = 7.0 mm (9/32 inches)When converted to a 35 mm still cameraFor movies: 47 mm (1 7/8 inches) (16:9)For still images: 42 mm (1 11/16 inches) (4:3)
Exposure control: Automatic exposure, Scene Selection (4 modes)
File format:Still images: Exif Ver. 2.21 JPEG compliant, DCF compliantMovies: MPEG-4 compliant (.MP4)
Video codec type: MPEG-4 AVC/H.264 Main ProfileAudio codec type: AAC LC
Recording media: Internal Memory (approx. 12 MB), “Memory Stick PRO Duo” media
[Input and Output connectors]USB jack: mini B, Hi-Speed USB (USB 2.0
compliant)A/V OUT jack: Minijack, Video out, audio out (mono)
[LCD screen]LCD panel: 4.6 cm (1.8 type) TFT driveTotal number of dots: 230 400 (960 × 240) dots
[Power, general]Power: Rechargeable battery pack NP-BK1, 3.6 V
AC-LS5K AC Adaptor (sold separately),4.2 V
Power consumption: 2.0 W (when the movie image size is [720 30P])
Operating temperature: 0 to 40°C (32 to 104°F)Storage temperature: –20 to +60°C (–4 to +140°F)Dimensions: Approx. 23.5 × 103.3 × 55.3
(15/16 × 4 1/8 × 2 1/4 inches)(W/H/D, excluding protrusions)
Mass: Approx. 120 g (4.2 oz) (including NP-BK1 battery pack, etc.)
Microphone: Monaural
Speaker: MonauralExif Print: CompatiblePRINT Image Matching III: Compatible
BC-CSK/BC-CSKA battery chargerPower requirements: AC 100 V to 240 V,
50 Hz/60 Hz, 2.2 WOutput voltage: DC 4.2 V, 0.33 AOperating temperature: 0 to 40°C (32 to 104°F)Storage temperature: –20 to +60°C (–4 to+140°F)Dimensions: Approx. 62 × 24 × 91 mm (2 1/2 ×
31/32 × 3 5/8 inches) (W/H/D)Mass: Approx. 75 g (2.7 oz)
Rechargeable battery packNP-BK1Used battery: Lithium-ion batteryMaximum output voltage: DC 4.2 VMean output voltage: DC 3.6 VMaximum charge voltage: DC 4.2 VMaximum charge current: 1.4 ACapacity:typical: 3.4Wh (970mAh)minimum: 3.3Wh (930mAh)
Design and specifications are subject to changewithout notice.
— 3 —MHS-PM1
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.
2. Check the interboard wiring to ensure that no wires are“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.
5. Check the B+ voltage to see it is at the values specified.6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚Cduring repairing.
• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).
• Be careful not to apply force on the conductor when solderingor unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!
• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.Dispose of used batteries according to the instructions.
1-1EMHS-PM1
1. SERVICE NOTE
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note 1: When replacing the main frame assy, erase the data in internal memory of the board before replacement.Note 2: When replacing the main frame assy, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
Copies all images in the internal memory to “Memory Stick PRO Duo” media.
1 Insert “Memory Stick PRO Duo” media.
2 Select [Copy] with the multi-selector tilt to v/V/b/B, then tilt to B.
3 Select [OK] with v, then press the multi-selector.The message “All data in internal memory will be copied” appears.
4 Select [OK] with v, then press the multi-selector.Copying starts.
To cancel the copyingSelect [Cancel] in step 4, then press the multi-selector.
• Charge the battery sufficiently. Copying image files when the remaining battery amount is low can cause data transfer failure or damage the data due to battery exhaustion.
• You cannot copy individual images.• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick PRO Duo” media after copying, then execute the [Format] command in [Internal Memory Tool].
• When you copy the data in the internal memory to the “Memory Stick PRO Duo” media, a new folder is created. You cannot choose a specific folder on the “Memory Stick PRO Duo” media as the destination for the data to be copied.
• Even if you copy data, a (Sharemark) or a (Print order) mark is not copied.
Copy
This item appears only when “Memory Stick PRO Duo” media is not inserted in the camera.
Formats data stored in the internal memory.• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [Format] with the multi-selector tilt to v/V/b/B, then tilt to B.
2 Select [OK] with v, then press the multi-selector.The message “All data in internal memory will be erased” appears.
3 Select [OK] with v, then press the multi-selector.The format is completed.
To cancel the formattingSelect [Cancel] in step 3, then press the multi-selector.
Format
2-1MHS-PM1
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
1 STOPPER SCREW2 CLAW3 CABINET (REAR) ASSY4 KNOB BUTTON
1 STOPPER SCREW2 LCD SHEET METAL3 JOINT SCREW4 CLAW5 CABINET (FRONT) ASSY6 JACK COVER
1
1 4
3
1
2
2
(To page 2-2)
1 STOPPER SCREW2 KY PC BOARD CORNER CARD
1 STOPPER SCREW2 MAIN BOARD3 LCD BLOCK ASSY
1
1
3
3
5
4
1
1
1
2
1
1
2
3
2
6
2-2EMHS-PM1
1 BRUSH STOPPER SCREW2 BRUSH3 STOPPER SCREW4 LENS MODULE5 LENS RETAINER
1 STOPPER SCREW2 BEARING3 STOPPER SCREW4 HINGE5 LENS (FRONT) ASSY6 STOPPER SCREW7 LENS (REAR) COVER8 LENS STOPPER SCREW9 SHIELD CASE CUSHION0 LENS CONNECTION WIREqa LENS ASSY
1
1
2
3
4
2
3
4
5
6
7
qa
8
9
0
5
(From page 2-1)
3-1EMHS-PM1
3. BLOCK DIAGRAM
3-1. OVERALL BLOCK DIAGRAM
USB_D+USB_D-
CMOS_D[0..11]
CMOS_VDCMOS_HDCMOS_MCLKCMOS_PIXCLK
SHUT1SHUT2
NAND_WP
MS_D[0..3]
LCD_MCLK
MS_PWRMS_BSMS_CLK
MS_D[0..3]MS_INS#MS_BSMS_CLK
NAND_RENAND_ALENAND_CLE
NAND_IO[0..7]
NAND_WE
NAND_R/B
RAMODT
RAMLDQSRAMLDQS_N
RAMUDQS_NRAMUDQS
RAMLDMRAMUDMRAMCLKRAMCLK_NRAMCASRAMRASRAMWE_NRAMCLK_ENRAMA[0..12]RAMBA[0..2]
SHUT_1SHUT_2
+1.8VD
MS_INS#
MS_PWR+3.1VD_MS
+3.1VD_MS
MS_LED
MS_LED
VIDEO_IOBVIDEO_IORVIDEO_IOG
VIDEO_IOB
VIDEO_IORVIDEO_IOG
I2S_WSCLK_AUI2S_SOI2S_SII2S_CLK
I2S_WS
CLK_AU
I2S_SO
I2S_SI
I2S_CLK
LCD_VDLCD_HD
VD_OUT[0..5]
LCD_VDLCD_HD
VD_OUT[0..5]
VD_OUT[6..15]
VD_OUT[6..15]
SSIO_EN0
SSIO_SCLKSSIO_SDATA
SSIO_EN0
SSIO_SCLKSSIO_SDATA
SSIO_SCLKSSIO_SDATA
LCD_RST
LCD_RST
LCD_EN
LCD_EN
UART0_TXUART0_RX
UART0_TXUART0_RX
USB_D+USB_D-USB5V
USB5VC_DET
C_DET
K_POWER_DET
LED_POWER
LED_POWER
DC_DETBAT_XP0BAT_XP1BAT_LEVELBAT_STROBE
DC_DET
BAT_STROBE
BAT_LEVEL
BAT_THM
BAT_THM
K_TRASH
K_INETRNET
PHOTO_S2PHOTO_S1
K_WIDEK_TELE
K_MENU
K_TRASHK_INETRNET
PHOTO_S2PHOTO_S1K_WIDEK_TELE
K_MENU
K_POWER
VD_OUT10
LED_POWER
PWR_HOLD
PWR_HOLD
LCD_MCLK+1.2VD
+1.2VD
+3.1VD
+3.1VD
+3.1VD
+3.1VD
+3.1VD
+3.1VD
+3.1VD
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
DGND
K_POWER
RAMD[0..15]
BAT_XP0BAT_XP1
K_ADC
+3.3VS
+3.3VS
+3.3VS
LED-
LED+
VP
VP
+1.2VD
+1.8VD
+1.8VD
+2.8VD
+2.5VD
+2.5VD
ROTATE_FLIPROTATE_OPEN
ROTATE_FLIPROTATE_OPEN
Lineout_LLineout_R
ROTATE_OPEN
+2.5VD
+3.5V
+3.5V
LCD_BL_PWM
LCD_BL_PWM
+3.1V
+3.3VS
+3.1VD
DGND
DGND
VD_OUT10
+3.1VDDGND
JTAG_TDIJTAG_TMSJTAG_RSTJTAG_CLKJTAG_TDO
JTAG_TDIJTAG_TMSJTAG_RSTJTAG_CLKJTAG_TDO
K_ADC
+2.5VD
+2.5VD
IOGND
IOGND
VIDEO_SELECT
VIDEO_SELECT
PWR_CTRLSHUT1SHUT2
+3.1VD
CMOS_MCLK
CMOS_PWR
+3.1V
K_POWER_DET
+1.2VD+2.5VD
SSIO_EN1
SSIO_EN1
+3.1VD
+3.1V
NAND_WPNAND_CE
CMOS_RST#CMOS_TRIGCMOS_SCLKCMOS_SDATACMOS_STANDBY
C_VD
USB/TV JACK
Power
Li-Batt
CPU
Nand Flash Audio
MS Card
05_CMOS
05_CMOS
CMOS_PWRCMOS_D[0..11]
DGND
CMOS_PIXCLK
CMOS_SDATACMOS_SCLK
CMOS_RST#
CMOS_STANDBY
+2.8VD
SHUT_1SHUT_2CMOS_TRIG
+3.1V
+1.8VD
CMOS_MCLK
CMOS_HDCMOS_VD
+3.1VD
C_VD
07_MS CARD
07_MS CARD
MS_INS#
MS_LEDMS_BS
MS_D[0..3]DGND
MS_CLK
+3.1VD_MS
+3.1VD
03_DSP_3/3
03_DSP_3/3
DGND+3.3VS+1.2VD+2.5VD
+3.1VD
02_DSP_2/3
02_DSP_2/3
K_ADC
LCD_VDLCD_HD
DGND NAND_IO[0..7]
NAND_CLENAND_WE
NAND_ALE
CMOS_MCLK
CMOS_D[0..11]
NAND_CENAND_R/B
NAND_RE
BAT_LEVELC_DET
VIDEO_IORVIDEO_IOGVIDEO_IOB
CMOS_VDCMOS_HD
CMOS_PIXCLK
LCD_MCLK
+2.8VD
VD_OUT[0..5]
USB5V
USB_D+USB_D-
PHOTO_S2PHOTO_S1
MS_PWR
MS_CLKMS_BS
I2S_WS
I2S_CLKI2S_SII2S_SO
+1.2VD
MS_D[0..3]
CLK_AU
K_WIDE
BAT_THM
K_INETRNET
K_TELE
BAT_XP0BAT_XP1
+2.5VD
JTAG_TDOJTAG_CLKJTAG_RST
JTAG_TDIJTAG_TMS
+3.1VD
CMOS_PWR
K_POWER_DET
04_DDR
04_DDR
DGNDRAMODTRAMD[0..15]
RAMLDQSRAMLDQS_N
RAMUDQSRAMUDQS_N
RAMLDMRAMUDM
RAMCASRAMRASRAMWE_NRAMCLK_EN
RAMCLKRAMCLK_N
RAMA[0..12]RAMBA[0..2]+1.8VD
08_LCD
08_LCD
DGND
LCD_MCLK
SSIO_CLKSSIO_SDATA
LCD_VD
VD_OUT[0..5]VD_OUT[6..15]SSIO_EN0
VD_OUT10
LCD_RST
LCD_EN
LED+
LED-
LCD_HD
+3.1VD
01_DSP_1/3
01_DSP_1/3
DGND
RAMD[0..15]
PWR_HOLD
CMOS_RST#
RAMA[0..12]RAMBA[0..2]
RAMRASRAMCAS
RAMWE_NRAMCLK_EN
RAMODT
RAMLDQS
RAMUDQS
RAMLDQS_N
RAMUDQS_N
RAMLDMRAMUDMRAMCLK
RAMCLK_N
NAND_WP
UART0_TXUART0_RX
CMOS_SCLKCMOS_SDATA
SSIO_SCLKSSIO_SDATA
MS_LED
MS_INS#
K_TRASH
CMOS_TRIG
DC_DET
CMOS_STANDBY
VD_OUT[6..15]
SSIO_EN0
LCD_BL_PWM
SHUT1SHUT2
LCD_RST
LCD_EN
BAT_STROBE
LED_POWER
K_MENU
ROTATE_OPENROTATE_FLIP
+1.2VD
VIDEO_SELECT
+3.1VD
+1.8VD
C_VD
SSIO_EN1
09_SWITCH
09_SWITCH
DGND
+3.3VS
K_TRASH
K_POWER
LED_POWER
K_MENU
K_WIDE +2.5VD
K_INETRNET
K_TELE
PHOTO_S1PHOTO_S2
ROTATE_OPENROTATE_FLIP
K_ADC
+3.1VD
10_AUDIO
10_AUDIO
I2S_SO
I2S_SI
CLK_AUI2S_CLK
Lineout_L
I2S_WS
Lineout_R
DGND
+3.5V
SSIO_EN1
SSIO_SCLKSSIO_SDATA
06_NAND
06_NAND
DGND
NAND_RENAND_ALENAND_CLE
NAND_IO[0..7]
NAND_R/B
NAND_WE
NAND_WP
NAND_CE
+3.1VD
11_POWER PATCH
11_POWER PATCH
DGND
VPBAT_LEVEL
DC_DET
BAT_STROBE
BAT_XP0BAT_XP1
BAT_THM+2.5VD
IOGND
+3.1VD
12_POWER
12_POWER
VP
+3.3VS
+1.2VD
+1.8VD
LED-
LED+
MS_PWR
+2.5VD
LCD_BL_PWM
+3.1V
DGND
PWR_CTRLSHUT1
SHUT_1SHUT2
SHUT_2
+3.5V
+3.1VD_MS+3.1VD
13_IO
13_IO
USB_D+USB_D-UART0_TXUART0_RXVD_OUT10VIDEO_IOB
C_DET
VIDEO_IORVIDEO_IOG +3.3VS
DGND
USB5VPWR_HOLD
ROTATE_OPENK_POWER
Lineout_LLineout_R
JTAG_TDOJTAG_CLKJTAG_RST
JTAG_TDIJTAG_TMS
+2.5VD
IOGND
VIDEO_SELECTPWR_CTRL
+3.1VD
K_POWER_DET
+3.1V
4. REPAIR PARTS LIST
4-1MHS-PM1
(ENGLISH)NOTE:• -XX, -X mean standardized parts, so they may have some differences from
the original one.• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.• The mechanical parts with no reference number in the exploded views are not
supplied.• Due to standardization, replacements in the parts list may be different from
the parts specified in the components used on the set.
When indicating parts by reference number,please include the board name.
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
• Color Indication of Appearance PartsExample:(SILVER) : Cabinet’s Color(Silver) : Parts Color
• AbbreviationAR : Argentine modelAUS : Australian modelBR : Brazilian modelCH : Chinese modelCND : Canadian modelEE : East European modelHK : Hong Kong modelJ : Japanese modelJE : Tourist modelKR : Korea modelNE : North European model
4-2MHS-PM1
Ref. No. Part No. Description Ref. No. Part No. Description
1 X-2348-760-1 CABINET (FRONT) ASSY (S) (SILVER)1 X-2348-761-1 CABINET (FRONT) ASSY (D) (ORANGE)1 X-2348-762-1 CABINET (FRONT) ASSY (V) (VIOLET)2 X-2348-757-1 CABINET (REAR) ASSY (S) (SILVER)2 X-2348-758-1 CABINET (REAR) ASSY (D) (ORANGE)
2 X-2348-759-1 CABINET (REAR) ASSY (V) (VIOLET)3 4-141-576-01 BUTTON, KNOB (SILVER)3 4-141-576-11 BUTTON, KNOB (ORANGE)3 4-141-576-21 BUTTON, KNOB (VIOLET)4 4-141-560-01 SCREW, JOINT
5 4-141-559-01 SCREW, STOPPER6 4-141-561-01 LCD SHEET METAL7 4-141-574-01 COVER, JACK (SILVER)7 4-141-574-11 COVER, JACK (ORANGE)7 4-141-574-21 COVER, JACK (VIOLET)
8 4-141-573-01 LID, BT (SILVER)8 4-141-573-11 LID, BT (ORANGE)8 4-141-573-21 LID, BT (VIOLET)
4-1-1. OVERALL SECTION
ns: not supplied
4-1. EXPLODED VIEWS
2
7
6
4
4
4
4
5
5
5
58
1
3
Main Frame Section(See page 4-3)
5 5
ns(Note)
Note: In case of the main frame assy failure, contact yourlocal Sony service Headquarter for the measures.
4-3MHS-PM1
Ref. No. Part No. Description Ref. No. Part No. Description
51 A-1709-921-A LCD BLOCK ASSY52 4-141-559-01 SCREW, STOPPER
053 1-817-331-11 DC JACK 5P54 1-815-794-13 CONNECTOR (MULTIPLE)55 4-134-399-01 CONNECTOR, USB
56 X-2348-766-1 FRAME ASSY57 4-141-575-01 TERMINAL, BATTERY
58 4-141-562-01 BRUSH59 4-145-214-01 SCREW, BRUSH STOPPER60 A-1709-884-A CARD, KY PC BOARD CORNER
61 4-141-571-01 RETAINER, LENS (LOWER) (SILVER)61 4-141-571-11 RETAINER, LENS (LOWER) (ORANGE)61 4-141-571-21 RETAINER, LENS (LOWER) (VIOLET)
4-1-2. MAIN FRAME SECTION
ns: not supplied
5152
53
52
52
52
52
5455
56
57
58
ns
ns(Note)
59 60
61
Lens Module Section(See page 4-4)
Note: In case of the main board failure, contact your local Sonyservice Headquarter for the measures.
• Refer to page 4-1 for mark 0.
4-4MHS-PM1
4-1-3. LENS MODULE SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
101 X-2348-763-1 LENS (FRONT) ASSY (S) (SILVER)101 X-2348-764-1 LENS (FRONT) ASSY (D) (ORANGE)101 X-2348-765-1 LENS (FRONT) ASSY (V) (VIOLET)102 4-141-564-01 HINGE103 4-141-563-01 BEARING
104 4-141-559-01 SCREW, STOPPER
105 4-141-572-01 WIRE, LENS CONNECTION106 X-2348-777-1 CUSHION, SHIELD CASE107 4-141-583-01 SCREW, LENS STOPPER108 4-141-565-01 COVER, LENS (REAR) (SILVER)
108 4-141-565-11 COVER, LENS (REAR) (ORANGE)108 4-141-565-21 COVER, LENS (REAR) (VIOLET)
101
103
102104
104
105
104
106
107
108
ns(Note)
Note: In case of the lens assy failure, contact your local Sonyservice Headquarter for the measures.
4-5EMHS-PM1
Checking supplied accessories.4-2. ACCESSORIES
Battery Charger(BC-CSK/BC-CSKA)0 1-487-212-11 (US, CND)
Battery Charger(BC-CSK/BC-CSKA)0 1-487-212-21
(AEP, UK, NE, E)
Power Cord (Mains Lead)0 1-832-169-41 (UK)0 1-834-482-21 (AEP, NE, E)
Rechargeable Battery Pack(NP-BK1)
(Note)
A/V Connecting Cable1-823-156-61
USB Cable4-134-402-01
Hand Strap2-050-981-01
Component A/V Cable1-834-646-11
CD-ROM(PMB (Picture Motion Browser)including PMB Guide/Mobile HD Snap Camera Handbook (PDF))
4-140-975-01
Instruction Manual4-135-531-12 (ENGLISH) (US, CND, AEP, UK)4-135-531-21 (FRENCH) (CND, AEP)4-135-531-32 (SPANISH) (US, AEP, E)4-135-531-41 (DUTCH) (AEP)4-135-531-51 (PORTUGUESE) (AEP)4-135-531-61 (GREEK) (AEP)4-135-531-71 (GERMAN) (AEP)4-135-531-81 (ITALIAN) (AEP)4-135-531-91 (TURKISH) (AEP)4-140-060-11 (POLISH, CZECH, HUNGARIAN, SLOVAK)
(AEP)4-140-060-21 (SWEDISH, DANISH, FINNISH, ROMANIAN)
(AEP)4-140-060-31 (RUSSIAN, UKRAINIAN) (NE)
Mobile HD Snap Camera Handbook (PDF)
The CD-ROM supplied contains all of language version ofthe Mobile HD Snap Camera Handbook (PDF) for printing.・ The printed matter is not supplied. If required, please
order it with the part number below.
* 4-135-530-11 (ENGLISH)* 4-135-530-21 (FRENCH)* 4-135-530-31 (SPANISH)* 4-135-530-41 (DUTCH)* 4-135-530-51 (PORTUGUESE)* 4-135-530-61 (GREEK)* 4-135-530-71 (GERMAN)* 4-135-530-81 (ITALIAN)* 4-135-530-91 (TURKISH)* 4-140-058-11 (POLISH)* 4-140-058-21 (CZECH)* 4-140-058-31 (HUNGARIAN)* 4-140-058-41 (SLOVAK)* 4-140-058-51 (SWEDISH)* 4-140-058-61 (DANISH)* 4-140-058-71 (FINNISH)* 4-140-058-81 (ROMANIAN)* 4-140-058-91 (RUSSIAN)* 4-140-059-11 (UKRAINIAN)
Conversion 2P Adaptor0 1-569-008-12 (E)
Note: This item is supplied with the unit as an accessory, butis not prepared as a service part.
• Refer to page 4-1 for mark 0.
Ver. 1.1 2009.06The changed portions fromVer. 1.0 are shown in blue.
MHS-PM1
[Regarding Fuse]• MAIN BOARD
Ref. No.: F1MANUFACTURER: AEM, Inc.TYPE: F0402FA1500V024TRATING: 1.5A/24V
Revision History
Reverse
MHS-PM1
Ver.
1.0
1.1
Date
2009.02
2009.06
History
Official Release
Revised-1(A1 09-053)
Contents
—
• Addition of E Model• Revision of AccessoriesS.M. revised: Page 4-5
S.M. Rev.issued
—
Yes
985266812.pdf