speccatos proct maes intended use: the beacon …€¢ in addition, matrix can be specified with...

CERTIFICATIONS/LISTINGS

PRODUCT IMAGE(S)SPECIFICATIONS

Beacon Products • 2041 58th Avenue Circle East Bradenton, FL 34203 • Phone: 800-345-4928 Due to our continued efforts to improve our products, product specifications are subject to change without notice.© 2017 BEACON PRODUCTS, All Rights Reserved • For more information visit our website: www.beaconproducts.com • Printed in USA June 8, 2018 8:53 AM

Cat.#

Approvals

Job TypeMATRIXAReA/POST TOP

Intended Use:The Beacon Matrix luminaire is available in three configurations with a wide choice of different LED wattage configurations and optical distributions designed to replace HID lighting up to 1000W MH or HPS. Luminaires are suitable for wet locations.

Construction:• Manufactured with die cast aluminum.• Coated with a polyester finish that meets ASTM B117 corrosion test requirements and ASTM D522 cracking and loss of adhesion test requirements. • External hardware is corrosion resistant. • One piece optical cartridge system consisting of an LED engine, LED lamps, optics, gasket and stainless steel bezel.• Cartridge can be field replaced as a one piece optical system. • Silicone gasket ensures a weather-proof seal around each individual optic.

Electrical: • Luminaire accepts 100V through 277V, 50 Hz to 60 Hz (UNV), 347V, or 480V input. • Power factor is ≥ .90 at full load. • Dimming drivers are standard, but must contact factory to request wiring leads for purpose of external dimming controls.• Component-to-component wiring within the luminaire may carry no more than 80% of rated load and is certified by UL for use at 600VAC at 90°C or higher. • Fixture electrical compartment shall contain all LED driver components and optional push-button terminal block for AC power connections. • Optional 7-pin ANSI C136.41-2013 twist-lock photo control receptacle available. Compatible with ANSI C136.41 external wireless control devices.• Ambient operating temperature -40°C to 40°C• Surge protection - 20kA. ANSI/IEEE category C high

Controls/Options:• Available with an optional passive infrared (PIR) motion sensor capable of detecting motion 360° around the luminaire. When no motion is detected for the specified time, the motion response system reduces the wattage to factory preset level, reducing the light level accordingly. When motion is detected by the PIR sensor, the luminaire returns to full wattage and full light output. Please contact Beacon Products if project requirements vary from standard configuration. • Available with Energeni for optional set dimming, timed dimming with simple delay, or timed dimming based on time of night (see www.beaconproducts.com/products/energeni).

• In addition, Matrix can be specified with SiteSync™ wireless control system for reduction in energy and maintenance costs while optimizing light quality 24/7. For more details, see ordering information or visit: www.hubbelllighting.com/sitesync

Installation: • Mounting options for horizontal arm, vertical tenon or traditional arm mounting available. Mounting hardware included. • Adjustable knuckle is designed to slip fit a 2” tenon that is 2 3/8” OD by 4” in length.• Luminaire can adjust in 5˚ increments.

Finish: • IFS polyester powder-coat electrostatically

applied and thermocured. IFS finish consists of a five stage pretreatment regimen with a polymer primer sealer and top coated with a thermoset super TGIC polyester powder coat finish.

• The finish meets the AAMA 2604 performance specification which includes passing a 3000 hour salt spray test for corrosion resistance and resists cracking or loss of adhesion per ASTM D522 and resists surface impacts of up to 160 inch-pounds.

Certifications/Ratings:• DesignLights Consortium (DLC) qualified, consult DLC website for more details: http://www.designlights.org/QPL• Certified to UL 1598, UL 8750, and CSA C22.2 No. 250.0• IP65 optical assembly• IDA approved

Warranty:Five year limited warranty for more information visit: www.hubbelllighting.com/resources/warranty

DIMENSIONS

��

��

��

��

��

��

��

��

29.7

25.0

��

��

��

��

4.9

29.7 25.0

36.2

41.9

11.7

PRELIMINARY

Upswept ArmPost Top

Mast ArmKnuckle

Model Mount Weight lbs. Weight kgs. EPA, Sq. ft.

Area MAFARMPost-TopKnuckle, 0˚Knuckle, 30˚

73.580.089.586.0

33.436.440.739.1

1.71.72.51.73.8

IP65

Sensors, photocells and wireless controls should not be tilted above horizontal.

http://www.designlights.org/QPL


PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.hubbell-automation.com/products/sitesync/ or contact Hubbell Lighting tech support at (800) 345-4928.

SiteSync fixtures with Motion control (SWPM) require the mounting height of the fixture for selection of the lens.

Examples: MAA/96L-555/4K7/3/UNV/K/GT/SWP SiteSync only MAA/96L-555/4K7/3/UNV/K/GT/SWPM/40F SiteSync with Motion Control

ORDERING EXAMPLE: MAA/96L-555/5K7/2/UNV/ASQ/DBT/7PR-TL/BC

MA/A

SERIES

MA/A Matrix

VOLTAGE

UNV 120-277V

347 347V

480 480V

CCT/CRI7

5K7 5000K, 70 CRI

4K7 4000K, 70 CRI

3K7 3000K, 70 CRI

5K8 5000K, 80 CRI

4K8 4000K, 80 CRI

3K8 3000K, 80 CRI

5K9 5000K, 90 CRI

4K9 4000K, 90 CRI

3K9 3000K, 90 CRI

DISTRIBUTION

FR Type 1/Front Row

2 Type 2

3 Type 3

4 Type 4

5R Type 5 Rectangular

5QM Type 5 Square Med

5QW Type 5R Square Wide

ROTATION

Leave blank for no rotation

L1 Optic rotation left

R1 Optic rotation right

COLOR

DB Dark Bronze Textured

BL Black Textured

WH White Textured

PS Plat. Silver Smooth

GYS Light Gray Smooth

GT Graphite Textured

TT Titanium Textured

CC Custom Color

MOUNTING

ASQ Arm Square

A2 Arm mount for 2.4”-3.0” OD round pole




K8 Knuckle (5o adjustable fitter)

PT2 Post top of 2 3/8” tenon (3.5 bottom OD)

ENGINE

80L-260 260W, 33,000 lm

96L-315 315W, 40,000 lm

64L-325 325W, 37,000 lm

64L-370 370W, 40,000 lm

80L-405 405W, 45,000 lm

80L-465 465W, 50,000 lm

96L-490 490W, 55,000 lm

96L-555 555W 60,000 lm

CONTROL OPTIONS

7PR11 7-PIN Receptacle only

7PR-TL7 7 pin PCR w/ Twist Lock photo control

7PR-SC 7 pin PCR w/ shorting cap

2PF 2 power feed with 2 drivers

GENI2,3 Energeni

SCL/40F Low voltage sensor for 7PR-SC and wiSCAPE external control accessory

SCP/40F2,4,5 Programmable Line

Voltage sensor SWP

2,6SiteSync Pre-Commission

SWPM/40F2,6

SiteSync Pre-Commission w/Sensor

OPTIONS

BC Backlight Control

SF120 120V Fuse

SF277 277V Fuse

SF347 347V Fuse

DF208 208V Fuse

DF240 240V Fuse

DF480 480V Fuse

TB9 Terminal Block

BS Bird Spikes

Control Accessories

NXOFM-1R1D-UNV On-fixtre (7-pin), On / Off / Dim, Day-light sensor with HubbNET Radio and Bluetooth Radio, 120-480VAC

SWUSB* SiteSync interface software loaded on USB flash drive for use with owner supplied PC (Windows based only). Includes SiteSync license, software and USB radio bridge node.

SWTAB* Windows tablet and SiteSync interface software. Includes tablet with preloaded software, SiteSync license and USB radio bridge node.

SWBRG+ SiteSync USB radio bridge node only. Order if a replacement is required or if an extra bridge node is requested.

SCPREMOTE Order at least one per project location to program and control

SW7PR+ SiteSync 7 Pin on fixture module On/Off/Dim, Daylight Sensor 120-480VAC

WIR-RME-L10 wiSCAPE external control node

Accessories

MAA-BC Backlight Control accessory kit

Accessories and Services (Ordered Separately)

1 Not available with 5QM or 5QW distribution. 2 Not available with other sensor or wireless control options.3 Specify routine setting code (example GENI-04). See ENERGENI brochure and instructions for setting table options.4 Photocell included with sensor, additional photocontrol not recommended.5 Order at least one SCPREMOTE per project location to program and control the occupancy sensor6 Specify group and zone at time of order. See www.hubbell-automation.com/products/sitesync/ for more details. Order at leaset one SiteSync interface Accessory SWUSB or SWTAB. Each option contains SiteSync License, GUI, and Bridge Node7 7PR-TL shipped with shorting cap installed. Twist-lock photocell shipped with fixture. Installer must remove shorting cap and install photocell at time of installation.8 Limited to applications requiring 30˚ tilt or less. If higher angle tilt is required use flood version with glass cover9 Not available on K or PT2 mountings 10 Requires 7PR-SC photocell receptacle. Include SCL/40F if occupancy sensing is required11 Shorting cap, phot control, or wireless control provided by others

* When ordering SiteSync at least one of these two interface options must be ordered per project.

+ If needed, an additional Bridge Node can be ordered.

++ Available as a SiteSync retrofit solution for fixtures with an existing 7pin receptacle.

SiteSync 7-Pin Module• All of the SiteSync Features in a new form • Available as an accessory for new construction or retrofit

applications (with existing 7-Pin receptacle) • Available on all products that have a 7-Pin receptacle

SW7PR

Catalog Number Description HCS System

NXOFM-1R1D-UNV On-fixture Module (7-pin), On / Off / Dim, Daylight Sensor with HubbNET Radio and Bluetooth® Radio, 120-480VAC

NX Distributed Intelligence™

WIR-RME-L On-fixture Module (7-pin or 5-pin), On / Off / Dim, Daylight Sensor with wiSCAPE Radio, 110-480VAC

wiSCAPE™ Lighting Control

For additional information related to these accessories please visit www.hubbellcontrolsolutions.com. Options provided for use with integrated sensor, please view specification sheet ordering information table for details.

Hubbell Control Solutions - Accessories (sold separately)

Catalog Number DescriptionRPA Round Pole adapters are available for 2, 3, 4.5, 5, and 6 inch diameter round poles

RPA2-ARA3-XX1 Round Pole adapters for 2-1/2” – 3” diameter mounting surfaceRPA3-ARA3-XX1 Round Pole adapters for 3” – 3-3/4” diameter mounting surfaceRPA4-ARA3-XX1 Round Pole adapters for 3-7/8” – 4-1/2” diameter mounting surfaceRPA5-ARA3-XX1 Round Pole adapters for 5” – 6” diameter mounting surfaceRPA6-ARA3-XX1 Round Pole adapters for 6” diameter mounting surface

SETA2-XX1 Square pole tenon adapter (4 at 90 degrees) (2 3/8” OD tenon)RETA2-XX1 Round pole tenon adapter (4 at 90 degrees) (2 3/8” OD tenon), requires CL1S-RPA4-ACC-XX for each luminaireTETA2-XX1 Hexagonal pole tenon adapter (3 at 120 degrees) (2 3/8” OD tenon)

1 Replace XX with color choice, eg.: DB for Dark Bronze

MOUNTING OPTIONS & ACCESSORIES


MOUNTING ARM DIMENSIONS

PHOTOMETRICSType 2 Type 3 Type 4

Type 5QMType 5R

Type 5W

Type 5QW

Type FR

Type TC

Front Row Applications

Tennis Court Applications

PROJECTED LUMEN MAINTENANCEAMBIENT

TEMP. 0 25,000 50,000

1TM-21-11 60,000 100,000

Calculated L70(HOURS)

25°C / 77°F 1 0.95 0.90 0.89 0.81 >150,000

40°C / 104°F 0.99 0.93 0.88 0.86 0.78 >145,0001 Projected per IESNA TM-21-11Data references the extrapolated performance projections for the 700mA base model in a 25°C ambient, based on 10,000 hours of LED testing per IESNA LM-80-08.

# LED'sNumber of

Drivers

Drive Current

[milliamps]INPUT VOLTAGE

(V)Oper. Current

(AMPS)System

Power (W)

96

2 1800

120 4.7

559208 2.7240 2.3277 2.0347 1.6480 1.2

2 1600

120 4.1

496208 2.4240 2.1277 1.8347 1.4480 1.0

2 1050

120 2.6

316

208 1.5240 1.3277 1.1347 0.9480 0.7

80

2 1800

120 3.9

465

208 2.2240 1.9277 1.7347 1.3480 1.0

2 1600

120 3.4

405

208 1.9240 1.7277 1.5347 1.2480 0.8

1 1050

120 2.2

262

208 1.3240 1.1277 0.9347 0.8480 0.5

64

2 1800

120 3.1

370

208 1.8240 1.5277 1.3347 1.1480 0.8

2 1600

120 2.8

336

208 1.6240 1.4277 1.2347 1.0480 0.7

ELECTRICAL DATA

EPA Config. EPA

1 1.2

2 @ 90˚ 1.9

2 @ 180˚ 2.4

Config. EPA

3 @ 120˚ 3.0

3 @ 90˚ 3.1

4 @ 90˚ 3.8

LUMINAIRE AMBIENT TEMPERATURE FACTOR (LATF)AMBIENT TEMPERATURE LUMEN MULTIPLIER

0°C 32°F 1.0510°C 50°F 1.0220°C 68°F 1.0125°C 77°F 1.0030°C 86°F 0.9940°C 104°F 0.9850°C 122°F 0.96

MOUNTING ARM DIMENSIONS

3.50

1.75.875

.625

.875

.625

FULL ROUND2X R .312

1.692

3.505

1.75

MA arm incorporates hole pattern provisions for most major luminaire manufacturers providing retrofit solutions to existing poles. Two bolt patterns range from 1.75” to 5.25” are accommodated. Arms are acceptable for 90˚ configurations.

Utilize S2 hole pattern when ordering poles


5K(5000K nominal, 70 CRI)



# LED’S

DRIVE CURRENT

(MILLIAMPS)SYSTEM WATTS DISTRIBUTION TYPE LUMENS LPW1 B U G LUMENS LPW1 B U G LUMENS LPW1 B U G

64 1600 325

FR 42696 131 3 0 2 42711 131 3 0 2 39960 122 3 0 22 40433 124 4 0 4 40447 124 4 0 4 37842 116 3 0 43 40215 123 3 0 5 40229 123 3 0 5 37638 115 3 0 54 40446 124 3 0 5 40460 124 3 0 5 37855 116 3 0 5

5R 40993 126 5 0 5 41007 126 5 0 5 38367 117 5 0 55QM 41912 128 5 0 4 41926 128 5 0 4 39226 120 5 0 45QW 41013 126 5 0 4 41028 126 5 0 4 38386 118 5 0 4

64 1800 370

FR 46401 125 3 0 2 46417 125 3 0 2 43428 117 3 0 22 43942 119 4 0 5 43957 119 4 0 5 41126 111 4 0 53 43705 118 3 0 5 43720 118 3 0 5 40905 111 3 0 54 43956 119 3 0 5 43972 119 3 0 5 41140 111 3 0 5

5R 44551 120 5 0 5 44566 120 5 0 5 41696 113 5 0 55QM 45549 123 5 0 5 45565 123 5 0 5 42631 115 5 0 45QW 44573 120 5 0 5 44588 121 5 0 5 41717 113 5 0 5

80 1050 260

FR 37761 144 3 0 2 37761 144 3 0 2 35411 135 3 0 22 35760 136 3 0 4 35760 136 3 0 4 33534 128 3 0 43 35567 135 3 0 5 35567 135 3 0 5 33353 127 3 0 54 35772 136 3 0 5 35772 136 3 0 5 33545 128 3 0 5

5R 36255 138 5 0 5 36268 138 5 0 5 33998 130 5 0 55QM 37068 141 5 0 4 37068 141 5 0 4 34760 132 5 0 45QW 36273 138 5 0 4 36273 138 5 0 4 34015 130 5 0 4

80 1600 405

FR 53370 131 3 0 3 53388 131 3 0 3 49950 122 3 0 22 50541 124 4 0 5 50558 124 4 0 5 47303 116 4 0 53 50269 123 3 0 5 50286 123 3 0 5 47048 115 3 0 54 50558 124 3 0 5 50575 124 3 0 5 47319 116 3 0 5

5R 51241 126 5 0 5 51259 126 5 0 5 47958 117 5 0 55QM 52389 128 5 0 5 52408 128 5 0 5 49033 120 5 0 55QW 51267 126 5 0 5 51285 126 5 0 5 47982 118 5 0 5

80 1800 465

FR 58002 126 3 0 3 58022 125 3 0 3 54285 117 3 0 32 54927 119 4 0 5 54946 119 4 0 5 51408 111 4 0 53 54631 118 4 0 5 54650 118 4 0 5 51131 111 3 0 54 54946 119 3 0 5 54965 119 3 0 5 51425 111 3 0 5

5R 55688 121 5 0 5 55708 120 5 0 5 52120 113 5 0 55QM 56936 123 5 0 5 56956 123 5 0 5 53288 115 5 0 55QW 55716 121 5 0 5 55735 121 5 0 5 52146 113 5 0 5

96 1050 315

FR 45313 144 3 0 2 45313 144 3 0 2 42493 135 3 0 22 42911 136 4 0 5 42911 136 4 0 5 40240 128 4 0 43 42681 135 3 0 5 42681 135 3 0 5 40024 127 3 0 54 42926 136 3 0 5 42926 136 3 0 5 40254 128 3 0 5

5R 43506 138 5 0 5 43521 138 5 0 5 40798 129 5 0 55QM 44481 141 5 0 5 44481 141 5 0 5 41712 132 5 0 45QW 43528 138 5 0 5 43528 138 5 0 5 40818 129 5 0 4

96 1600 490

FR 64044 130 3 0 3 64066 130 3 0 3 59940 122 3 0 32 60649 123 4 0 5 60670 123 4 0 5 56763 115 4 0 53 60322 123 4 0 5 60343 123 4 0 5 56457 115 4 0 54 60669 123 3 0 5 60691 123 3 0 5 56782 115 3 0 5

5R 61490 125 5 0 5 61511 125 5 0 5 57550 117 5 0 55QM 62867 128 5 0 5 62889 128 5 0 5 58839 120 5 0 55QW 61520 125 5 0 5 61541 125 5 0 5 57578 117 5 0 5

96 1800 555

FR 69602 125 4 0 3 69626 125 4 0 3 65142 117 3 0 32 65912 118 4 0 5 65935 118 4 0 5 61689 110 4 0 53 65557 117 4 0 5 65580 117 4 0 5 61357 110 4 0 54 65935 118 4 0 5 65958 118 4 0 5 61710 110 3 0 5

5R 66826 119 5 0 5 66849 119 5 0 5 62544 112 5 0 55QM 68323 122 5 0 5 68347 122 5 0 5 63946 114 5 0 55QW 66859 119 5 0 5 66882 120 5 0 5 62575 112 5 0 5

PERFORMANCE DATA

1 Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown. Actual performance may differ as a result of end-user environment and application.2 315W and 395W 3000K versions are not DLC QPL listed. Reference highlighted cells in table.


PROJECTED LUMEN MAINTENANCEELECTRICAL DATA

PHOTOMETRICSType 2 Type 3 Type 4

Type 5QMType 5R

Type 5W

Type SQN

Type FR

Type TC

Front Row Applications

Tennis Court Applications

# OF LEDS

NUMBER OF

DRIVERS

DRIVE CURRENT

(mA)INPUT VOLTAGE

(V)SYSTEM POWER

(W)CURRENT(Amps)

96

2 1800

120

559

4.7208 2.7240 2.3277 2.0347 1.6480 1.2

2 1600

120

496

4.1208 2.4240 2.1277 1.8347 1.4480 1.0

2 1050

120

316

2.6208 1.5240 1.3277 1.1347 0.9480 0.7

80

2 1800

120

465

3.9208 2.2240 1.9277 1.7347 1.3480 1.0

2 1600

120

405

3.4208 1.9240 1.7277 1.5347 1.2480 0.8

1 1050

120

262

2.2208 1.3240 1.1277 0.9347 0.8480 0.5

64

2 1800

120

370

3.1208 1.8240 1.5277 1.3347 1.1480 0.8

2 1600

120

336

2.8208 1.6240 1.4277 1.2347 1.0480 0.7

AMBIENTTEMP. 0 25,000 50,000

1TM-21-11 60,000 100,000

Calculated L70(HOURS)

25°C / 77°F 1 0.95 0.90 0.89 0.81 >150,000

40°C / 104°F 0.99 0.93 0.88 0.86 0.78 >145,0001 Projected per IESNA TM-21-11Data references the extrapolated performance projections for the base model in a 25°C ambient, based on 10,000 hours of LED testing per IESNA LM-80-08.

AMBIENT TEMPERATURE LUMEN MULTIPLIER0°C 32°F 1.0510°C 50°F 1.0220°C 68°F 1.0125°C 77°F 1.0030°C 86°F 0.9940°C 104°F 0.9850°C 122°F 0.96

Use these factors to determine relative lumen output for average ambient temperatures from 0-40°C (32-104°F).

speccatos proct maes intended use: the beacon …€¢ in addition, matrix can be specified with...

Documents