strength - es. i
TRANSCRIPT
Straight & folding sliding door system for heavy commercial interior & exterior applications up to 1000kg
Runners Series 250 is a top hung system which utilises the highest quality components. The smooth running hangers feature hardened steel tyres and precision stainless steel bearings for a lifetime of reliable service with the minimum of maintenance.
Runners Series 250 is designed for heavy duty commercial and agricultural applications such as warehousing, agricultural buildings, hangars etc. The comprehensive range of hangers and components offers a smooth gliding system for both straight sliding and folding configurations. Series 250 maximum panel weight capacity is 1000kg*.*capacity based on 2 x 500kg hangers per panel.
Strength
55mm ball bearing wheels with hardened steel tyre and stainless steel bearings.
series
Wheel Types
31t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
series
Track
Straight sliding components
Straight sliding systems for timber or metal doors
Brackets:Face fixing
Brackets:Soffit fixing
Hangers
Suspension Plates Guide channel Track Stops
Series 250 straight sliding systems are suitable for timber or metal doors with a maximum panel weight up to 1000kg when using two 500kg 4 wheel hangers per door. Capacity will be reduced accordingly if using lower capacity hangers from the Series 250 range. Components suitable for use with straight sliding systems are detailed below. Generally two hangers are used on each door panel. A third or fourth hanger can be used to increase door weight capacity. eg. using three 250-253 hangers would allow a door panel weighing up to 1500kg to be used.
When using upper track support brackets they should be fixed at a minimum of 600mm and a maximum of 1000mm spacing. Series 250 upper track is NOT pre-drilled and will require drilling for soffit fixing whether installing it with or without the use of soffit fixing brackets. Our Technical Team are available on 01280 822288 to help you with system configuration and hardware selection if required.
Track
Track stopHanger
Suspension plate
Bracket
Guide channel
Bottom guide
Typical panel configurations
Single track run
Double track run
TECHNICAL ADVICEConsult our Technical Team on 01280 822288 for help with hardware configuration and quantities.
See page 37 for full range details
series
series
250-250
250-81 250-265
250-259 250-259D 250-258
250-252 250-253 250-253B 250-262 250-263 250-1383
250-1298
250-257 50-1257
250-73
250-69 250-70 250-77 250-1271 250-268
Bottom Guides
32t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
Straight sliding application examples
Face Fixing
Soffit Fixing
Technical
250-259
250-250
250-250
250-253(252)
250-253B
55 min95 max
55
Ø24
Ø16
46 min55 max
250-257
250-255
250-255
250-259
160
25 min
With canopy (see page 43)
33t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
series
Bottom Guide Options A B
A. Screw mounted guide roller fixed to timber door with under guide channel recessed into floor.B. Screw mounted guide roller fixed to metal door with under guide channel recessed into floor.C. Bottom guide 250-77 used with angle steel, which can also act as a weather strip.D. T-section metal bar fitted to door underside and used with bottom guide 250-77E. Bottom guide 250-1271 fixed into floor using chemical resin. Door is then guided between wall and roller which allows it to be used with no under guide channel. Where guide channel is prone to fill with debris, this method is recommended.
Metal door
250-69(70)250-81
8
250-77Other bottom guide options available. See GUIDE ROLLER section on page 39
Metal door
Metal door
C D
30 min
5 max5 max
250-77
250-1271
Typical bottom guide configurations for sliding systems (suggestions only).
45 min
250-268250-81
E
min 5
Hole Ø20
Face Fixing
Polyester Resin (Product ref AFJ 350)
Technical
250-259
250-250
250-1383
55 min95 max
Ø18
27 max
250-255
34t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
Centre Folding SystemsSeries 250 end folding systems are suitable for timber or metal doors with a maximum panel weight up to1000kg when using two 500kg 4 wheel hangers per door. Capacity will be reduced accordingly if using lower capacity hangers from the Series 250 range. Components suitable for use with centre folding systems are detailed below. Our Technical Team are available on 01280 822288 to help you with system configuration and hardware selection if required.
Centre Folding door components series
Track
Bracket
Hanger
Rotating Suspension plate
Guide channel
Bottom guide
TECHNICAL ADVICEConsult our Technical Team on 01280 822288 for help with hardware configuration and quantities.
Track Brackets:Face fixing
Brackets:Soffit fixing
Hangers
Suspension Plates Guide channel
Track Stops
See page 23 for full range details
250-250
250-81
250-265
250-259
250-259D
250-258
250-252 250-253 250-253B 250-262 250-263 250-1383
250-1298
250-257 50-1257
250-73
250-69250-70
250-77 250-1271 250-268
Bottom Guides
Other typical centre folding panel configurationsAll panels equal width except jamb leaf which must be reduced as shown above.
Typical plan of 3 1/2 doors
Hinged at jamb
Hinged at jamb
Hinged at jamb
Access panel
Allow clearance for hinge knuckles when
using butt hinges
NOTE: The width of the door panel which is hinged to the frame (jamb) must be reduced by half the thickness of the door plus half the width of the remaining doors, plus the diameter of the hinge knuckle when using butt hinges.The example below is for a hinge with a 14mm knuckle. Dimension will vary depending on hinge choice.
Example using 1200mm wide x 80mm thick door.
1200mm ÷ 2 = 600mm; 80mm ÷ 2 = 40mm;
600mm + 40mm + 14mm
= 654mm reduction in width.
Technical
35t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
series
Bottom Guide Options
A BA. Screw mounted guide roller fixed to timber door with under guide channel recessed into floor. 250-1298 may also be used for door tinner than 40mm
B. Screw mounted guide roller fixed to metal doorMetal door
250-69(70)250-81
8
Other bottom guide options available. See GUIDE ROLLER section on page 30
Typical bottom guide configurations for folding systems (suggestions only).
End Folding
Technical
250-259
250-250
250-253
20 min
30 max
50
Ø24
46 min
250-257
250-259250-253
250-268250-81
With canopy (see page 43)
36t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
Tracks & Guides250-250
Galvanised steel upper trackLength Part No.
1 metre 250-250-12 metre 250-250-23 metre 250-250-34 metre 250-250-45 metre 250-250-5
250-81Under guide galvanised steel channel
29.2
25.8
35.2
Length Part No.
1 metre 250-81-12 metre 250-81-23 metre 250-81-34 metre 250-81-45 metre 250-81-5
Actual Size
57.5
67
Actual Size
3.0
Brackets
250-258 Ceiling fixing steel bracket for the upper track.
250-259 Wall fixing steel bracket for the upper track.
250-259D Twin track wall fixing steel bracket for the upper track. Maximum spacing adjustment 33mm
80
115
10
6768
6060
100
250-259D250-258 250-259Ø12.8
Ø12.8
8237
16.4
77
67
33 max
59
177
Track will require drilling to accept
M10 bolti
Track will require drilling to accept
M10 bolti
Upper track is available bent by special order to a specific radius.i
All steel track and guide channels are supplied in galvanised finish. Regular greasing is required to prevent premature wear from friction.i
37t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
series
Please note that when using upper track support brackets it is recommended that they should be fixed at 600mm - 1000mm spacing. i
Hanger wheel technical information
42.5
31.7521.0
55
series
Hangers/plates
250-252 | 220kg capacity
250-262 | 220kg capacity 250-263 | 380kg capacity
250-1383 | 280kg capacity
250-253B | 400kg capacity
250-253 | 500kg capacity
Adjustable steel hanger with M20 x 80mm pin and 55mm ball bearing wheels.
Adjustable steel hanger with M20 x 97mm rotating pin and 55mm ball bearing wheels.
Adjustable steel hanger with M20 x 97mm rotating pin and 55mm ball bearing wheels.
Adjustable steel hanger with M16 x 80mm pin and 55mm ball bearing wheels.
Adjustable steel hanger with M16 x 160mm pin and 55mm ball bearing wheels.
Adjustable steel hanger with M20 x 80mm pin and 55mm ball bearing wheels.
55mm ball bearing steel wheels.
55mm ball bearing steel wheels. 55mm ball bearing steel wheels.
55mm ball bearing steel wheels.
55mm ball bearing steel wheels.
55mm ball bearing steel wheels.
160
200 200
175
165
160
24080
97 97
80
80
160
250-252
250-262
250-257
250-263250-1383
250-253
250-253B220kg
220kg 380kg
280kg
500kg
400kg
250-257 Steel rotating suspension plate for M20 pin.Min. door thickness 46mm.For use with: 250-252; 250-253; 250-262; 250-263
50-1257 Steel rotating suspension plate for M16 pin. Min. door thickness 46mm.For use with: 250-253B; 250-1383
14014.5
45
50-1257
14014.5
45
38t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
Guide rollers/accessories
250-268
250-73 Steel side guide roller with rotating brass pin 25mm diameter.Minimum door thickness 40mm.
AFJ 350 Polyester Resin 300mlParticularly suitable for anchoring studs and bolts into hollow walls and masonry. Fits in a standard sealant gun.
250-69 Steel guide roller with rotating brass pin 25mm diameter.
250-70 Steel guide roller with rotating brass pin 25mm diameter.
250-77 Twin steel guide roller with rotating brass pin 25mm diameter.
250-1271 Guide roller M16 steel pin with 34mm steel roller.
250-268 Guide roller M12 steel pin with 25mm brass roller.
111
40
73
39 72
39 72
50 72
Gap8.0
93 84
50-1297
250-1298 Rotating brass pin 25mm diameter.
250-69 250-70
250-77
250-255
250-255 Door stop for the upper track.
250-1271
250-73
Quiesce
Architectural Folding Door Systemsfor Timber DoorsOverhead Runway Systems Sliding Door Kits
trakkitmultirail™
& SMARTSPRAY™
Other products available from Runners Sliding Systems
Ask for a brochure
39t. 01280 822288 f. 01280 813024 e. [email protected] w. www.runners-uk.com
series