submittal transmittal alley 111 apartments project ... resource station/resources...1 0231 - 079100...

Detailed, Grouped by Each Number

Submittal Transmittal

Skanska USA Building Inc.Alley 111 Apartments Project # 4212049-000

Tel: Fax:

Date: 2/17/2015 Reference Number: 0491

Transmitted To: Transmitted By: Debbie LimJosh Clothier

Grund & Company Skanska USA Building Inc.1115 N. 97thSeattle, WA 98103-3311Tel: 206.522.0755Fax: 206.524.3749

929 109th Ave NEBellevue, WA 98004

Submittal Package No Description Due Date Package ActionQty

Approved as Noted2/9/2015Grund - Water Repellent Sample WAR, PD0231 - 079100 - 01

Transmitted For Delivered Via Tracking Number

EmailApproval

Notes Item ActionItems DescriptionQty

0002 Water Repellents - Product Literature

Approved as Noted1

0003 Water Repllenets - Warranty Draft

Approved as Noted1

Contact Name Copies NotesCompany NameCc:

Remarks

No exceptions taken.

Signature Signed Date

Prolog Manager Printed on: 2/17/2015 6west

-Submittal Transmittal

02/09/2015Due Date:

Detailed, Grouped by Each Number

Skanska USA Building Inc.Alley 111 Apartments Project # 4212049-000

Tel: Fax:

Date: 1/26/2015 Reference Number: 0457

Transmitted To: Transmitted By: Debbie LimKevin Reed

GGLO Skanska USA Building Inc.1301 First Avenue Suite 301Seattle, WA 98101Tel: (206) 467-5828

929 109th Ave NEBellevue, WA 98004

Submittal Package No Description Due Date Package ActionQty

2/9/2015Grund - Water Repellent Sample WAR, PD0231 - 079100 - 01

Transmitted For Delivered Via Tracking Number

EmailApproval

NotesItems DescriptionQty Spec Section Sub Sec.

0002 Water Repellents - Product Literature

1 071900 1.2.B.

0003 Water Repellents - Warranty Draft

1 079100 1.2D

Remarks

Signature Signed Date

Prolog Manager Printed on: 1/26/2015 6west Page 1

Debbie.Lim

Submittal Stamp

kevinr

Submittal

Protectosil® AQUA-TRETE® 20WATER REPELLENTProduct Data and Test Information

PRODUCT DESCRIPTIONA clear, penetrating,waterborne, breathable water repellent for use on concrete and masonry. Ready-to-use, low-VOC, si-lane emulsion. Reduces the ingress of water and waterborne contaminants that cause premature deterioration of the sub-strate. Penetrates the substrate and chemically bonds with sil-ica to form a permanent attachment of the water repellent molecule. ProtectosilAQUA-TRETE 20 water repellent is especially suited for application when solvent-borne products are not acceptable, as in states that have VOC regulations for AIM coatings. Protectosil AQUA-TRETE 20 meets all na-tional and state VOC regulations.

By preventing water and waterborne contaminants from en-tering the substrate, Protectosil AQUA-TRETE 20 reduces such problems as efflorescence, leaching, acid rain deteriora-tion, scaling, dirt buildup, staining, corrosion of reinforcing steel and mildew. Treated surfaces are fully breathable be-cause their natural moisture vapor transmission is not affect-ed. This will reduce problems that entrapped moisture can cause, including blushing of the sealer and freeze-thaw dam-age.

APPROPRIATE APPLICATIONSFor use on concrete to protect the reinforcing steel from cor-rosion due to the effects of water, deicing salts and other wa-terborne chemicals.

Protects precast concrete (including GFRC) from the damag-ing effects of acid rain and freeze-thaw cycles. Keeps concrete clean by reducing the amount of dirt and other pollutants that it may absorb.Some denser concrete masonry units (split-face, fluted or ground-face blocks) and pavers can also be protected from water absorption.

Other suitable substrates include brick masonry, sandstone, terra-cotta, hand molded bricks and some natural stones.

ADVANTAGESProtectosil AQUA-TRETE 20 is a silane/siloxane blend in a proprietary emulsion system. Unlike other silane or siloxane emulsion systems, Protectosil AQUA-TRETE 20 is ready touse and is suitable for concrete and brick masonry, without the need to blend oils, silicones, stearates or acrylatesinto the system. Protectosil AQUA-TRETE 20 is designedto provide a high level of repellency with penetration. Theactive components are unique because they chemically bondto the silica in the substrate and set up a hydrophobic layer ofprotection. By incorporating Protectosil AQUA-TRETE 20into your integrated design, you can earn vital Leadership inEnergy & Environmental Design (LEED) credits for both

new and existing construction projects.

The main benefits of the product are:• Non flammable• Excellent resistance to chloride ion ingress• Reduced efflorescence• Breathable system• Good penetration into substrate• No change in surface appearance• High resistance to alkali attack• Long service life• Substrates already treated with Protectosil AQUA- TRETE 20 can be painted over• Keeps substrates cleaner

LIMITATIONSNot intended for below-grade waterproofing. Will leavea residue on nonporous materials such as glass, metaland painted surfaces. Shrubbery and plant life should beprotected from overspray. Keep away from asphalt andbituminous materials.

Should not be applied if the surface temperature is below40°F (5°C) or above 100°F (40°C), if rain is expected within8 hours following application, or if high winds or otherconditions prevent proper application. If rain has precededthe application, the surface should be allowed to dry for atleast 24 hours.

TECHNICAL DATAProtectosil AQUA-TRETE 20 is an emulsioncomposed of alkyltrialkoxysilane resins in water. Color emulsion Active Substance silane/siloxane Active Content 20% Solvent water Flash Point > 200oF Density 8.3 lb/gal VOC 90 g/l

TEST DATAAASHTO T 259 “90-Day Salt Ponding”(150 ft2/gal coverage rate)0-0.5 inch depth 93% reduction0.5-1.0 inch depth 86% reduction

NCHRP #244 (@150 ft2/gal)Series II 80% reduction in water absorptionSeries II 84% reduction in chloride absorptionSeries IV 96% reduction in chloride absorption (continued)

Debbie.Lim

Callout

Degussa Building Systems has been replaced by Evonik. -DL1/26/15

For more information, MSDS and the most updated product information, and to find your local representative, go to www.protectosil.com

Protectosil®, AQUA-TRETE®= registered trademarks of Evonik IndustriesThis information and all technical and other advice are based on Evonik Corporation’s (“Evonik”) present knowledge and experience. However, Evonik as-sumes no liability for such information or advice, including the extent to which such information or advice may relate to third party intellectual property rights. Evonik reserves the right to make any changes to information or advice at any time, without prior or subsequent notice. EVONIK DISCLAIMS ALL REPRESENTATIONS AND WARRANTIES,WHETHER EXPRESS OR IMPLIED, AND SHALL HAVE NO LIABILITY FOR MERCHANT ABILITY OF THE PRODUCT OR ITS FITNESS FOR A PARTICULAR PURPOSE (EVEN IF EVONIK IS AWARE OF SUCH PURPOSE), OR OTHERWISE. EVONIK SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INDIRECT OR INCIDENTAL DAMAGES (INCLUDING LOSS OF PROFITS) OF ANY KIND. It is the customer’s sole responsibility and obligation to arrange for inspection and testing of all products by qualified experts. Reference to trade names used by other companies is neither a recommendation nor an endorsement of the corresponding product, and does not imply that similar products could not be used.

ASTM C 642 “Water Absorption of Concrete”24 hours 0.49%48 hours 0.68%

ASTM C 672 “Deicer Scaling”100 cycles — 0 rating(non-air-entrained Concrete)

ASTM D 1653 “Moisture Vapor Permeability of Organic Coatings”64 grams/ft2/24 hours, 93% breathability

INSTALLATIONConcrete must be allowed to cure for a minimum of 28 days.All repointing must be completed and allowed to cure for atleast 3 days. Concrete repair and replacement must becompleted prior to application of Protectosil AQUA- TRETE 20. Patching materials, caulking, sealing materialsand traffic paint must be fully cured before applyingProtectosil AQUA-TRETE 20.

All surfaces must be cleaned to remove all traces of dirt,dust, efflorescence, mold, salt, grease, oil, asphalt, laitance,curing compounds, paint, coatings and other foreignmaterials. Acceptable surface cleaning methods includeshotblasting, sandblasting, waterblasting and using chemicalcleaners. Check with your Protectosil representative to veri-fy that surface preparation is adequate.

Protectosil AQUA-TRETE 20 should be applied usinglow-pressure (15 to 25 psi) pumping equipment with a wetfan type spray nozzle. Alternate methods include usingeither a power roller with a 1” nap or a brush. Do not alteror dilute the material.

Do not apply to a wet or damp substrate. Immediately priorto using, mix or stir the material with a powered drum mixeror recirculating pump. A test patch should be applied to thesubstrate to verify coverage rate, application conditions anddesired results.

Substrate, air and product temperatures shall be between40°F and 100°F (5°C and 38°C) during application.Do not apply product if temperatures are expected to fallbelow 40°F (5°C) within 12 hours after application. Do notapply material if rain or other precipitation is expected with-in 8 hours.

On vertical surfaces, apply Protectosil AQUA-TRETE 20using a flooding application starting at the bottom and work-ing your way up, so the material runs down 6 to 8 inches be-low the spray pattern. For certain substrates, it may be nec-essary to apply a light fog coat to break the substrate’s surface tension before the flood coat. Coverage rates on ver-tical surfaces can vary and depend on the type of material to be treated. On horizontal surfaces, the liquid material should pond on the surface for at least 5 seconds before be-ing absorbed. For parking structures, consult the engineer’s

specification for their required application rate. For all oth-er projects you should consult your Protectosil representa-tive for the exact coverage rate on your particular project.

Protect glass, metal, plastic and other nonporous substratesfrom overspray. Protectosil AQUA-TRETE 20 will not etchglass but will leave a residue on nonporous surfaces.Protectosil AQUA-TRETE 20 should not darken or discolorthe substrate if used at the recommended coverage rates, butdue to variations in substrate porosity and environmentalconditions, applying a test patch is advised to verifycompatibility. For more detailed information on applyingProtectosil AQUA-TRETE 20, read “AQUA-TRETEWeatherproofing Application Instructions.”

Precautions: Protectosil AQUA-TRETE 20 productcontainers should be kept closed when not in use and shouldbe stored at temperatures between 35°F (2°C) and 100°F(40°C), away from rain and standing water. Protect productfrom freezing. Please read the material safety data sheet formore detailed information.

AVAILABILITYProtectosil AQUA-TRETE 20 is available in5- and 55-gallon drums. Shipped F.O.B. throughout the United States and Canada. Contact your local Protectosil representative or your regional manager for specific cost in-formation. You can obtain their contact information on our website, www.protectosil.com, or by calling us at 1 (800) 828-0919.

TECHNICAL SERVICETechnical service engineers and scientists are available toanswer questions about product performance, applicationmethods and compatibility with other building materials.You can speak to one of our engineers or scientists directly by calling our toll-free number, 1 (800) 828-0919, and se-lecting option 1.

MANUFACTUREREvonik Corporation299 Jefferson RoadParsippany, NJ 07054-06771 (800) [email protected]

PROTECTOSIL PRODUCTS ARE MANUFACTURED AT THE EVONIK CORPORATION THEODORE, ALABAMA, PLANT UNDER A QUALITY SYSTEM CERTIFIED TO ISO-9001 AND ISO-14001 REQUIREMENTS.

MATERIAL SAFETY DATA SHEET Protectosil® AQUA-TRETE® 20 Material no. Specification 150667 Order Number

Version 1.12 / US Revision date 04/12/2012 Print Date 03/27/2013 Page 1 / 7

MSDS-US (R11/011) / 4/12/2012 3:45

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING

Product information Trade name : Protectosil® AQUA-TRETE® 20 Company : Evonik Corporation USA

299 Jefferson Road Parsippany,NJ 07054-0677 USA

Telephone : 973-929-8000

Telefax : 973-929-8040

US: CHEMTREC EMERGENCY NUMBER

: 800-424-9300

CANADA: CANUTEC EMERGENCY NUMBER

: 613-996-6666

Product Regulatory Services : 973-929-8060

2. HAZARDS IDENTIFICATION *** EMERGENCY OVERVIEW ***

Form-liquid Color-white Odor-odorless May cause eye, skin and respiratory tract irritation.

POTENTIAL HEALTH EFFECTS

Eye contact Possibly irritating. Skin Contact Possibly irritating. Inhalation Possibly irritating. Ingestion The hazards of this material have not been fully investigated; ingestion may be hazardous. Chronic Health Hazard This product can hydrolyze to form a material posing additional health effects: Ethanol: ACGIH TLV: TWA 1000 ppm; OSHA PEL: TWA 1000 ppm. Liquid and high vapor concentrations cause eye irritation. Contact of liquid with skin causes drying, cracking, and irritation. Inhalation causes irritation of the respiratory tract. Repeated or prolonged exposure to



MSDS-US (R11/011) / 4/12/2012 3:45

high vapor concentrations may cause drowsiness. Excessive or repeated ingestion may cause central nervous system effects, liver effects and reproductive effects. However, ingestion is not an expected route of exposure. Ethanol has a low potential to cause allergic skin reactions; however, undocumented cases of human skin sensitization have been reported.

3. COMPOSITION/INFORMATION ON INGREDIENTS

Other information This material is classified as not hazardous under OSHA regulations.

4. FIRST AID MEASURES

Inhalation If inhaled, remove to fresh air. If breathing is difficult, give oxygen. If unconscious, evaluate the need for artificial respiration. Get immediate medical attention.

Skin contact Remove contaminated clothing/shoes. Flush skin with water. Follow by washing with soap and water. If symptoms develop or persist, obtain medical attention. Wash clothing before reuse.

Eye contact In case of contact, immediately flush eyes with plenty of water for at least 15 minutes or until all material has been removed. Obtain medical attention.

Ingestion Aspiration of material into the lungs may cause chemical pneumonitis (damage to lungs) which may be fatal. If swallowed, get medical attention immediately. Only induce vomiting if directed by a physician. Never give anything by mouth to an unconscious person.

5. FIRE-FIGHTING MEASURES

Flash point > 93.50 °C , > 200 °F Method: Tagliabue Closed Cup

Lower explosion limit not determined

Upper explosion limit not determined

Autoignition temperature not determined

Suitable extinguishing media Use water spray or fog, foam, dry chemical or CO2.

Special protective equipment for fire-fighters As in any fire, wear self-contained positive-pressure breathing apparatus, (MSHA/NIOSH approved or equivalent) and full protective gear.



MSDS-US (R11/011) / 4/12/2012 3:45

Further information Containers can build up pressure if exposed to heat (fire). Cool with water spray.

6. ACCIDENTAL RELEASE MEASURES

Personal precautions Wear personal protective equipment; see section 8.

Environmental precautions Obey relevant local, state, provincial and federal laws and regulations. Do not contaminate any lakes, streams, ponds, groundwater or soil.

Methods for cleaning up Absorb spill with inert material, then place in a chemical waste container.

7. HANDLING AND STORAGE

Handling

Safe handling advice Use with adequate ventilation.

Storage

Requirements for storage areas and containers Keep tightly closed in a dry and cool place.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

Engineering measures Ensure good ventilation during processing.

Personal protective equipment

Respiratory protection A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 or applicable federal/provincial requirements must be followed whenever workplace conditions warrant respirator use. NIOSH's "Respirator Decision Logic" may be useful in determining the suitability of various types of respirators.

Hand protection Use impermeable gloves.

Eye protection Use chemical splash goggles or face shield.

Skin and body protection A safety shower and eye wash fountain should be readily available. To identify additional Personal Protective Equipment (PPE) requirements, it is recommended that a hazard assessment in accordance with the OSHA PPE Standard (29CFR1910.132) be conducted before using this product.



MSDS-US (R11/011) / 4/12/2012 3:45

Hygiene measures Avoid contact with skin, eyes and clothing. Do not inhale vapors or aerosols. Do not eat, drink, or smoke when using the product. Remove contaminated or saturated clothing.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance

Form liquid Color white Odor odorless

Safety data

pH 7 (1 % solution)

Boiling point/range 100 °C

Flash point > 93.50 °C Method: Tagliabue Closed Cup

Autoignition temperature: not determined

Lower explosion limit not determined

Upper explosion limit not determined

Vapor pressure not determined

Water solubility miscible

Relative vapor density Heavier than air

Solvents and Volatiles Data % VOC (gm/l) 90

10. STABILITY AND REACTIVITY

Conditions to avoid Keep away from heat and sources of ignition.

Materials to avoid strong acids, Alkalies., strong bases, strong oxidants

Hazardous decomposition products Ethanol in case of hydrolysis

11. TOXICOLOGICAL INFORMATION

Product General Toxicity Information

No data is available on the product itself.



MSDS-US (R11/011) / 4/12/2012 3:45

12. ECOLOGICAL INFORMATION

General Ecological Information No ecotoxicological studies are available.

13. DISPOSAL CONSIDERATIONS

WASTE DISPOSAL

Advice on disposal Waste must be disposed of in accordance with local, state, provincial and federal laws and regulations. Empty containers must be handled with care due to product residue.

14. TRANSPORT INFORMATION

Transport/further information Not dangerous according to transport regulations.

15. REGULATORY INFORMATION

Information on ingredients / Non-hazardous components

This product contains the following non-hazardous components

Water CAS-No. 7732-18-5 Percent (Wt./ Wt.) NJTSR No.56705700001-6834P CAS-No. Trade Secret Percent (Wt./ Wt.)

US Federal Regulations

OSHA If listed below, chemical specific standards apply to the product or components:

• None listed

Clean Air Act Section (112)

If listed below, components present at or above the de minimus level are hazardous air pollutants:

• None listed CERCLA Reportable Quantities

If listed below, a reportable quantity (RQ) applies to the product based on the percent of the named component:

• None listed



MSDS-US (R11/011) / 4/12/2012 3:45

SARA Title III Section 311/312 Hazard Categories

The product meets the criteria only for the listed hazard classes:

• No SARA Hazards SARA Title III Section 313 Reportable Substances

If listed below, components are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:

• None listed

Toxic Substances Control Act (TSCA)

If listed below, non-proprietary substances are subject to export notification under Section 12 (b) of TSCA:

• None listed

State Regulations

The Listing requirements of the Right to Know (RTK) legislation varies by state. All information for NJ, PA, MA and other states can be derived from the listing of hazardous and non-hazardous components in section 2 and 15 of this MSDS.

California Proposition 65

A warning under the California Drinking Water Act is required only if listed below:

• None listed International Chemical Inventory Status

Unless otherwise noted, this product is in compliance with the inventory listing of the countries shown below. For information on listing for countries not shown, contact the Product Regulatory Services Department.

• Europe (EINECS/ELINCS) Listed/registered • USA (TSCA) Listed/registered • Canada (DSL) Not listed/Not registered • Australia (AICS) Not listed/Not registered • Japan (MITI) Not listed/Not registered • Korea (TCCL) Listed/registered • Philippines (PICCS) Listed/registered • China Not listed/Not registered • New Zealand Not listed/Not registered

16. OTHER INFORMATION

HMIS Ratings



MSDS-US (R11/011) / 4/12/2012 3:45

Health : 1 Flammability : 1 Physical Hazard : 0

NFPA Ratings

Health : 1 Flammability : 1 Reactivity : 0

Further information

Changes since the last version are highlighted in the margin. This version replaces all previous versions.

The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.

07 19 23 Water Repellents7

PRODUCT HIGHLIGHTS•Water repellency extends life of building•Treats lightweight block and CMU providing long-

lasting protection against moisture intrusion•VOC Compliant for EPA and most regional

jurisdictions•Excellent water bead so the substrate maintains

dry appearance during rainfall•Transparent and non-staining; does not alter

surface appearance•Breathablity allows interior moisture to escape

without damaging sealer•Easy to apply

HOW TO APPLySURfACe PRePARATIOn

1. Surfaces should be clean, dry, and free of alkali, efflorescence, sand, surface dust or dirt, oil, grease, chemical films, and other contaminants. Concrete surfaces should be fully cured.

2. Air, material, and surface temperatures should be 40° F (4° C) or higher during application and curing. Surfaces can be slightly damp prior to application, but for best results and maximum penetration of sealer, a dry surface is recommended. Do not apply sealer when temperatures are expected to fall below 40° F (4° C) within 4 hours of completed application.

3. Repoint any loose or disintegrated mortar and allow a minimum of 72 hours drying time before application. Install caulking and sealant before application, allowing a minimum of 6–12 hours curing time (or until set). Contact Technical Service for recommendations.

APPLICATIOn1. Test a small area of the surface (generally a 5

by 5 ft [1.5 by 1.5 m] section) before starting general application of any clear penetrating sealer to ensure desired performance results, aesthetics and coverage rates. Allow 2 weeks for the product to fully react before evaluating. Refer to Appendix HY-3: Test Area Application.

APPLICATIOnS• Vertical • Interior or exterior• Above grade

SUbSTRATeS• Concrete block Lightweight Integrally colored Split faced• Porous concrete surfaces

MasterProtect® H 185High-performance, breathable, water-based, patented silane/siloxane blended water-repellent sealer for lightweight blockFORMERLY EnVIROSEAL® PBT

DeSCRIPTIOn MasterProtect H 185 is a high-performance, water-based, clear, silane/siloxane sealer designed to provide long-term protection for the most challenging split-faced and lightweight block as well as standard CMU.

PACkAGInG– 5 gallon (19 L) pails– 54 gallon (205 L) drums

COLORMilky white; dries clear

yIeLD– Block (lightweight):

25–60 ft2/gal (0.6–1.5 m2/L)– Porous concrete:

60–150 ft2/gal (1.5–3.7 m2/L)

A test area is recommended to determine actual coverage rates. Coverage rates will vary greatly with the porosity of the substrate.

STORAGe Store in unopened containers in a clean, dry area between 35 and 110° F (2 and 43° C). Keep from freezing.

SHeLf LIfe 1 year when stored properly

VOC COnTenT Less than 118 g/L less water and exempt solvents.

Master Builders Solutions by BASF www.master-builders-solutions.basf.us

Technical Data Guide

Debbie.Lim

Callout

Per RFI 0430. -DL, 1/26/15

Technical DataCompositionMasterProtect H 185 is a water-based proprietary blend of silane and siloxane.

Test Data

Typical Properties

PROPERTY RESULTS TEST METHOD

PROPERTY VALUE

flash point, ° F (° C) > 212 (> 100) ASTM D 3278

Water repellency, % reduction > 95 ASTM C 140 in water absorption

Water permeance, % reduction, 99 ASTM E 514 leakage on block wall

Test results are averages obtained under laboratory conditions. Reasonable variations can be expected. Specific gravity, kg/L 1.0

Density, lb/gal 8.38

Penetration, in (mm), 1⁄16 – 1/4 average depth depending (1.5–6) upon substrate

yellowing none

efflorescence Highly resistant

Drying time for recoat, min 30 (if necessary)

Surface appearance after Unchanged application

Technical Data Guide MasterProtect® H 185

2. Mix material thoroughly before and during application.

3. Apply by low-pressure, non-atomizing spray.4. Apply a mist coat of MasterProtect H 185

immediately before application to help break surface tension and assist with maximum penetration.

5. Flood surfaces to saturation by applying from the bottom up, with a controlled 8–10" (20 cm) material rundown to ensure maximum penetration into substrate.

6. Extremely porous substrates may require 2 coats. Application of the second coat should proceed with a wet-on-wet application. Refer to Appendix HY-1: Sealing Lightweight Block.

DRyInG TIMeTypical drying time for MasterProtect H 185 is 4 hours at 70° F (21° C) and 50% relative humidity. Cooler temperatures or higher relative humidity can extend the drying time.

CLeAn UPClean equipment and tools with hot soapy water. Overspray can be cleaned immediately with hot soapy water. Dried residue can be cleaned with a mild citrus-based cleaner or very hot water, then scrubbed with a soft-bristle brush.

fOR beST PeRfORMAnCe• Keep material from freezing.• Do not dilute MasterProtect H 185.• Do not apply during inclement weather or when

inclement weather is anticipated within 2 hours.• To prevent damage to nearby shrubbery and

landscaping, cover or protect with drop cloth.• Variations in the texture and porosity of

the substrate will affect the coverage and performance of the product.

• Protect asphalt-based products such as roofing materials or plastic products from overspray

• MasterProtect H 185 will not inhibit water penetration through unsound or cracked surfaces or surfaces with defective flashing, caulking, or structural waterproofing.

•Make certain the most current versions of product data sheet and SDS are being used; visit master-builders-solutions.basf.us to verify the most current version.

•Proper application is the responsibility of the user. Field visits by BASF personnel are for the purpose of making technical recommendations only and are not for supervising or providing quality control on the jobsite.

HeALTH, SAfeTy AnD enVIROnMenTALRead, understand and follow all Safety Data Sheets and product label information for this product prior to use. The SDS can be obtained by visiting www.master-builders-solutions.basf.us, e-mailing your request to [email protected] or calling 1(800)433-9517. Use only as directed. for medical emergencies only, call ChemTrec® 1(800)424-9300.

LIMITeD WARRAnTy nOTICe BASF warrants this product to be free from manufacturing defects and to meet the technical properties on the current Technical Data Guide, if used as directed within shelf life. Satisfactory results depend not only on quality products but also upon many factors beyond our control. BASF MAKES nO OTHER WARRAnTY OR GUARAnTEE, EXPRESS OR IMPLIED, InCLUDInG WARRAnTIES OF MERCHAnTABILITY OR FITnESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ITS PRODUCTS. The sole and exclusive remedy of Purchaser for any claim concerning this product, including but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is the replacement of product or refund of the purchase price, at the sole option of BASF. Any claims concerning this product must be received in writing within one (1) year from the date of shipment and any claims not presented within that period are waived by Purchaser. BASF WILL nOT BE RESPOnSIBLE FOR AnY SPECIAL, InCIDEnTAL, COnSEQUEnTIAL (InCLUDInG LOST PROFITS) OR PUnITIVE DAMAGES OF AnY KInD.

Purchaser must determine the suitability of the products for the intended use and assumes all risks and liabilities in connection therewith. This information and all further technical advice are based on BASF’s present knowledge and experience. However, BASF assumes no liability for providing such information and advice including the extent to which such information and advice may relate to existing third party intellectual property rights, especially patent rights, nor shall any legal relationship be created by or arise from the provision of such information and advice. BASF reserves the right to make any changes according to technological progress or further developments. The Purchaser of the Product(s) must test the product(s) for suitability for the intended application and purpose before proceeding with a full application of the product(s). Performance of the product described herein should be verified by testing and carried out by qualified experts.

Master Builders Solutions by BASF www.master-builders-solutions.basf.us

Safety Data Sheet MasterProtect H 185 also ENVIROSEAL PBT Revision date : 2013/12/18 Page: 1/6Version: 4.0 (30605624/SDS_GEN_CA/EN)

1. Product and Company Identification

Company BASF Canada Inc. 100 Milverton Drive Mississauga, ON L5R 4H1, CANADA

24 Hour Emergency Response Information CANUTEC (reverse charges): (613) 996-6666 BASF HOTLINE: (800) 454-COPE (2673)

2. Hazards Identification

Emergency overview Contains a suspected reproductive toxin. Do not get in eyes, on skin, or on clothing. State of matter: liquid Colour: white Odour: product specific Potential health effects Acute toxicity: Ingestion may cause gastrointestinal disturbances. The product has not been tested. The statement has been derived from the properties of the individual components. Irritation / corrosion: May cause slight irritation to the eyes. May cause slight irritation to the skin. May cause slight irritation to the respiratory tract. The product has not been tested. The statement has been derived from substances/products of a similar structure or composition. Chronic toxicity: Carcinogenicity: The chemical structure does not suggest a specific alert for such an effect. Based on available Data, the classification criteria are not met. Repeated dose toxicity: No reliable data was available concerning repeated dose toxicity. Based on available Data, the classification criteria are not met. Reproductive toxicity: Contains a suspected reproductive toxin. Teratogenicity: The chemical structure does not suggest a specific alert for such an effect. Based on available Data, the classification criteria are not met.


Genotoxicity: The chemical structure does not suggest a specific alert for such an effect. Based on available Data, the classification criteria are not met. Signs and symptoms of overexposure: The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11. Potential environmental effects Aquatic toxicity: Based on available Data, the classification criteria are not met. There is a high probability that the product is not acutely harmful to aquatic organisms. Degradation / environmental fate: The polymer component of the product is poorly biodegradable. Bioaccumulation / bioconcentration: Discharge into the environment must be avoided.

3. Composition / Information on Ingredients

CAS Number Content (W/W) Hazardous ingredients 556-67-2 >= 3.0 - <= 7.0 % Cyclotetrasiloxane, octamethyl-

4. First-Aid Measures

General advice: First aid personnel should pay attention to their own safety. Immediately remove contaminated clothing. If inhaled: If difficulties occur after vapour/aerosol has been inhaled, remove to fresh air and seek medical attention. If on skin: After contact with skin, wash immediately with plenty of water and soap. Under no circumstances should organic solvent be used. If irritation develops, seek medical attention. If in eyes: Wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist. If swallowed: Rinse mouth immediately and then drink plenty of water, seek medical attention. Do not induce vomiting unless told to by a poison control center or doctor. Note to physician Treatment: Treat according to symptoms (decontamination, vital functions), no known

specific antidote.

5. Fire-Fighting Measures

Flash point: 93.34 °C (ASTM D3278) Flammability: not flammable Suitable extinguishing media: foam, water spray, dry powder, carbon dioxide


Unsuitable extinguishing media for safety reasons: water jet Protective equipment for fire-fighting: Wear a self-contained breathing apparatus. Further information: The degree of risk is governed by the burning substance and the fire conditions. If exposed to fire, keep containers cool by spraying with water. Collect contaminated extinguishing water separately, do not allow to reach sewage or effluent systems. Contaminated extinguishing water must be disposed of in accordance with official regulations.

6. Accidental release measures

Personal precautions: Do not breathe vapour/aerosol/spray mists. Wear eye/face protection. If exposed to high vapour concentration, leave area immediately. Use personal protective clothing. Handle in accordance with good building materials hygiene and safety practice. Environmental precautions: Contain contaminated water/firefighting water. Do not discharge into drains/surface waters/groundwater. Cleanup: For small amounts: Pick up with inert absorbent material (e.g. sand, earth etc.). Dispose of contaminated material as prescribed. For large amounts: Pump off product.

7. Handling and Storage

Handling

General advice: Avoid aerosol formation. Avoid inhalation of mists/vapours. Avoid skin contact. No special measures necessary provided product is used correctly.

Storage

General advice: Keep only in the original container in a cool, dry, well-ventilated place away from ignition sources, heat or flame. Protect from direct sunlight. Temperature tolerance Protect from temperatures below: 5 °C The packed product must be protected from temperatures below the indicated one.

8. Exposure Controls and Personal Protection

Personal protective equipment

Respiratory protection: Wear a NIOSH-certified (or equivalent) respirator as necessary. Hand protection: Wear chemical resistant protective gloves., Manufacturer's directions for use should be observed because of great diversity of types. Eye protection: Safety glasses with side-shields.


Body protection: Impermeable protective clothing General safety and hygiene measures: Do not inhale gases/vapours/aerosols. Avoid contact with the skin, eyes and clothing. Avoid exposure - obtain special instructions before use. Handle in accordance with good building materials hygiene and safety practice. Wearing of closed work clothing is recommended. When using, do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift. At the end of the shift the skin should be cleaned and skin-care agents applied. Gloves must be inspected regularly and prior to each use. Replace if necessary (e.g. pinhole leaks).

9. Physical and Chemical Properties

Form: liquid Odour: product specific Odour threshold: No data available. Colour: white pH value: approx. 4.6 ( 20 °C) Freezing point: No data available. Information on: Water Melting point: 0 °C ---------------------------------- Boiling point: Unspecified Information on: Water Boiling point: 100 °C ---------------------------------- Information on: Water Vapour pressure: 23.4 hPa ( 20 °C) Literature data. ---------------------------------- Density: approx. 1 g/cm3 ( 20 °C) Bulk density: not applicable Solubility in water: miscible Other Information: If necessary, information on other physical and chemical parameters is

indicated in this section.

10. Stability and Reactivity

Substances to avoid: strong acids, strong bases, strong oxidizing agents, strong reducing agents Hazardous reactions: The product is stable if stored and handled as prescribed/indicated. Decomposition products: No hazardous decomposition products if stored and handled as prescribed/indicated. Oxidizing properties: Based on its structural properties the product is not classified as oxidizing.

11. Toxicological information

Reproductive toxicity Information on: Cyclotetrasiloxane, octamethyl- The results of animal studies suggest a fertility impairing effect. ----------------------------------


Other Information: Based on our experience and the information available, no adverse health effects are expected if handled as recommended with suitable precautions for designated uses. The product has not been tested. The statements on toxicology have been derived from the properties of the individual components.

12. Ecological Information Degradability / Persistence Biological / Abiological Degradation Evaluation: Inherently biodegradable.

The insoluble fraction can be removed by mechanical means in suitable waste water treatment plants.

Other adverse effects: Ecological data are not available. Do not allow to enter soil, waterways or waste water channels.

13. Disposal considerations

Waste disposal of substance: Dispose of in accordance with national, state and local regulations. Residues should be disposed of in the same manner as the substance/product. Do not discharge into drains/surface waters/groundwater. Container disposal: Contaminated packaging should be emptied as far as possible; then it can be passed on for recycling after being thoroughly cleaned.

14. Transport Information

Land transport TDG

Not classified as a dangerous good under transport regulations

Sea transport IMDG


Air transport IATA/ICAO


15. Regulatory Information

Federal Regulations Registration status: Chemical DSL, CA released / listed


WHMIS classification: D2A: Materials Causing Other Toxic Effects - Very toxic

material

THIS PRODUCT HAS BEEN CLASSIFIED IN ACCORDANCE WITH THE HAZARD CRITERIA OF THE CPR AND THE MSDS CONTAINS ALL THE INFORMATION REQUIRED BY THE CPR.

16. Other Information

We support worldwide Responsible Care® initiatives. We value the health and safety of our employees, customers, suppliers and neighbors, and the protection of the environment. Our commitment to Responsible Care is integral to conducting our business and operating our facilities in a safe and environmentally responsible fashion, supporting our customers and suppliers in ensuring the safe and environmentally sound handling of our products, and minimizing the impact of our operations on society and the environment during production, storage, transport, use and disposal of our products.

SDS Prepared by: BASF NA Product Regulations [email protected] BASF HOTLINE (800) 454 – COPE (2673) SDS Prepared on: 2013/12/18 END OF DATA SHEET

January 21, 2015

MasterProtect® H 185 (formerly Enviroseal® PBT)

BASF CORPORATION

CONSTRUCTION SYSTEMS

Limited Warranty - Sample

Coverage :

Duration :

This is to certify that the above named product has been applied to the area described in the Project Site above.

This warranty makes no allowance for deviations or omissions from the information provided in the on-line

application. Any misrepresentation or fraudulent statement in the application for Limited Warranty renders the

5 Years

BASF Corporation (hereinafter BASF) Construction Systems, 889 Valley Park Drive, Shakopee, MN

55379, hereby warrants that, subject to the provisions hereof, the MasterProtect® H 185 (formerly

Enviroseal® PBT) (the “Product”) as manufactured satisfies the product performance criteria under

the terms specified in the current MasterProtect® H 185 (formerly Enviroseal® PBT) product data

sheet. The current product data sheet can be obtained at www.buildingsystems.basf.com. Any

claims brought against BASF relative to the referenced product and project shall constitute full

acceptance of all terms and conditions contained herein. The remedies of this warranty shall be

considered only when EACH of the following FIVE conditions exists: ( i) BASF must have been notified

of the unsatisfactory condition during the covered period following the date of application and this

notification to BASF shall be in writing within 30 days of the occurrence; (ii) BASF is afforded the

opportunity to inspect any such areas, at such time, as may be reasonably requested; (iii) The BASF

supplied product has been proven not to satisfy the published product performance criteria; (iv) This

product discrepancy must have directly contributed to the unsatisfactory condition in question; and (v)

Full payment has been received by BASF for the BASF materials supplied to the referenced project.

EXCLUSIONS:

This warranty does not apply, and BASF makes no warranty and disclaims all liability, where any

unsatisfactory condition resulting from misuse or abnormal use or conditions such as, but not limited

to: structural cracks or defects, faulty construction, design, non BASF materials, settlement or

expansion of the structure, accident, fire or other casualty, lack of suitable vapor barrier or excessive

wear. This warranty does not cover claims for color-fastness, appearance or offensive or unpleasant

odor; disintegration of the substrate; mechanical damage caused by individuals, tools, or other outside

agents; or any change in the appearance of the product from accumulated dirt or other contaminants .

This warranty does not apply, and BASF makes no warranty and disclaims all liability when an

unsatisfactory condition has occurred due to lack of adherence to all applicable care and maintenance

recommendations or cautions contained or referenced in the product data sheet. If the owner shall

make or permit, without prior written consent of BASF, repairs, alterations, or additions to the structure

which affect the product or change the use, function or purpose of the structure, this warranty shall

Material and Labor

Project Site

Name :

Address :

City :

State :

Applicator Name :

Purchaser Name :

Sample

Sample

Sample

Sample

Sample

Sample

Date of Application :

Page 1 of 2

become immediately null and void and of no further force and effect. BASF will respond promptly to

any written request for consent to repairs, alterations, or additions. Product performance properties

are limited to the material as supplied to the project.

REMEDIES:

The holder's sole and exclusive remedy and BASF's liability shall be limited to:

Providing MasterProtect® H 185 (formerly Enviroseal® PBT) in sufficient quantity and compensation

for the labor to replace solely those areas of the installed product proven to meet the terms of the

aforementioned warranty. A suitable replacement product may be employed at the sole discretion of

BASF. All other costs associated with the replacement of the product are the sole responsibility of the

holder. BASF's liability is limited to the original amount to install the BASF product supplied.

Holder and BASF specifically agree that any controversy or claim arising out of this warranty shall be

settled by arbitration in the state of Ohio, or in the state or province in which the project is located,

administered by the American Arbitration Association under its Commercial Arbitration Rules, and

judgment on any award rendered by the arbitrators may be entered in any court having jurisdiction

thereof.

If any part of this Warranty shall be determined to be invalid, then such portion shall be deemed

severed from this Warranty and the remaining terms, exclusions and limitations shall apply.

GENERAL LIMITATIONS

This information and all further technical advice are based on BASF's present knowledge and

experience. However, BASF assumes no liability for providing such information and advice including

the extent to which such information and advice may relate to existing third party intellectual property

rights, especially patent rights. In particular, BASF disclaims all CONDITIONS AND WARRANTIES,

WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A

PARTICULAR PURPOSE OR MERCHANTABILITY OR CLAIMS RELATED TO MOLD, MILDEW,

AND FUNGI OR ANY AIR QUALITY PROBLEMS. BASF SHALL NOT BE RESPONSIBLE FOR

CONSEQUENTIAL, INDIRECT OR INCIDENTAL DAMAGES (INCLUDING LOSS OF PROFITS) OF

ANY KIND. BASF does not warrant or guarantee the quality of labor used to prepare the surface and

to apply or install the products covered by this limited warranty. BASF reserves the right to make any

changes according to technological progress or further developments. It is the holder's responsibility

and obligation to carefully inspect and test any incoming goods. Performance of the product (s)

described herein should be verified by testing and carried out only by qualified experts. It is the sole

responsibility of the holder to carry out and arrange for any such testing. Reference to trade names

used by other companies is neither a recommendation, nor an endorsement of any product and does

not imply that similar products could not be used.

This warranty supersedes any other warranties, guarantees or representations, written or oral,

heretofore made with respect to the above referenced product or project.

Page 2 of 2

submittal transmittal alley 111 apartments project ... resource station/resources...1 0231 - 079100...

Documents